xref: /openbmc/u-boot/drivers/power/Kconfig (revision e1cc60c0)
1menu "Power"
2
3source "drivers/power/domain/Kconfig"
4
5source "drivers/power/pmic/Kconfig"
6
7source "drivers/power/regulator/Kconfig"
8
9choice
10	prompt "Select Sunxi PMIC Variant"
11	depends on ARCH_SUNXI
12	default AXP209_POWER if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
13	default AXP221_POWER if MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUN8I_R40
14	default AXP818_POWER if MACH_SUN8I_A83T
15	default SUNXI_NO_PMIC if MACH_SUNXI_H3_H5 || MACH_SUN50I
16
17config SUNXI_NO_PMIC
18	bool "board without a pmic"
19	---help---
20	Select this for boards which do not use a PMIC.
21
22config AXP152_POWER
23	bool "axp152 pmic support"
24	depends on MACH_SUN5I
25	select CMD_POWEROFF
26	---help---
27	Select this to enable support for the axp152 pmic found on most
28	A10s boards.
29
30config AXP209_POWER
31	bool "axp209 pmic support"
32	depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
33	select CMD_POWEROFF
34	---help---
35	Select this to enable support for the axp209 pmic found on most
36	A10, A13 and A20 boards.
37
38config AXP221_POWER
39	bool "axp221 / axp223 pmic support"
40	depends on MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUN8I_R40
41	select CMD_POWEROFF
42	---help---
43	Select this to enable support for the axp221/axp223 pmic found on most
44	A23 and A31 boards.
45
46config AXP809_POWER
47	bool "axp809 pmic support"
48	depends on MACH_SUN9I
49	select CMD_POWEROFF
50	---help---
51	Say y here to enable support for the axp809 pmic found on A80 boards.
52
53config AXP818_POWER
54	bool "axp818 pmic support"
55	depends on MACH_SUN8I_A83T
56	select CMD_POWEROFF
57	---help---
58	Say y here to enable support for the axp818 pmic found on
59	A83T dev board.
60
61config SY8106A_POWER
62	bool "SY8106A pmic support"
63	depends on MACH_SUNXI_H3_H5
64	---help---
65	Select this to enable support for the SY8106A pmic found on some
66	H3 boards.
67
68endchoice
69
70config AXP_DCDC1_VOLT
71	int "axp pmic dcdc1 voltage"
72	depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
73	default 3300 if AXP818_POWER || MACH_SUN8I_R40
74	default 3000 if MACH_SUN6I || MACH_SUN8I || MACH_SUN9I
75	---help---
76	Set the voltage (mV) to program the axp pmic dcdc1 at, set to 0 to
77	disable dcdc1. On A23 / A31 / A33 (axp221) boards dcdc1 is used for
78	generic 3.3V IO voltage for external devices like the lcd-panal and
79	sdcard interfaces, etc. On most boards dcdc1 is undervolted to 3.0V to
80	save battery. On A31 devices dcdc1 is also used for VCC-IO. On A83T
81	dcdc1 is used for VCC-IO, nand, usb0, sd , etc. On A80 dcdc1 normally
82	powers some of the pingroups, NAND/eMMC, SD/MMC, and USB OTG.
83
84config AXP_DCDC2_VOLT
85	int "axp pmic dcdc2 voltage"
86	depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
87	default 900 if AXP818_POWER
88	default 1400 if AXP152_POWER || AXP209_POWER
89	default 1200 if MACH_SUN6I
90	default 1100 if MACH_SUN8I
91	default 0 if MACH_SUN9I
92	---help---
93	Set the voltage (mV) to program the axp pmic dcdc2 at, set to 0 to
94	disable dcdc2.
95	On A10(s) / A13 / A20 boards dcdc2 is VDD-CPU and should be 1.4V.
96	On A31 boards dcdc2 is used for VDD-GPU and should be 1.2V.
97	On A23/A33 boards dcdc2 is used for VDD-SYS and should be 1.1V.
98	On A80 boards dcdc2 powers the GPU and can be left off.
99	On A83T boards dcdc2 is used for VDD-CPUA(cluster 0) and should be 0.9V.
100	On R40 boards dcdc2 is VDD-CPU and should be 1.1V
101
102config AXP_DCDC3_VOLT
103	int "axp pmic dcdc3 voltage"
104	depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
105	default 900 if AXP809_POWER || AXP818_POWER
106	default 1500 if AXP152_POWER
107	default 1250 if AXP209_POWER
108	default 1100 if MACH_SUN8I_R40
109	default 1200 if MACH_SUN6I || MACH_SUN8I
110	---help---
111	Set the voltage (mV) to program the axp pmic dcdc3 at, set to 0 to
112	disable dcdc3.
113	On A10(s) / A13 / A20 boards with an axp209 dcdc3 is VDD-INT-DLL and
114	should be 1.25V.
115	On A10s boards with an axp152 dcdc3 is VCC-DRAM and should be 1.5V.
116	On A23 / A31 / A33 boards dcdc3 is VDD-CPU and should be 1.2V.
117	On A80 boards dcdc3 is used for VDD-CPUA(cluster 0) and should be 0.9V.
118	On A83T boards dcdc3 is used for VDD-CPUB(cluster 1) and should be 0.9V.
119	On R40 boards dcdc3 is VDD-SYS and VDD-GPU and should be 1.1V.
120
121config AXP_DCDC4_VOLT
122	int "axp pmic dcdc4 voltage"
123	depends on AXP152_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
124	default 1250 if AXP152_POWER
125	default 1200 if MACH_SUN6I
126	default 0 if MACH_SUN8I
127	default 900 if MACH_SUN9I
128	---help---
129	Set the voltage (mV) to program the axp pmic dcdc4 at, set to 0 to
130	disable dcdc4.
131	On A10s boards with an axp152 dcdc4 is VDD-INT-DLL and should be 1.25V.
132	On A31 boards dcdc4 is used for VDD-SYS and should be 1.2V.
133	On A23 / A33 boards dcdc4 is unused and should be disabled.
134	On A80 boards dcdc4 powers VDD-SYS, HDMI, USB OTG and should be 0.9V.
135	On A83T boards dcdc4 is used for VDD-GPU.
136
137config AXP_DCDC5_VOLT
138	int "axp pmic dcdc5 voltage"
139	depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
140	default 1500 if MACH_SUN6I || MACH_SUN8I || MACH_SUN9I
141	---help---
142	Set the voltage (mV) to program the axp pmic dcdc5 at, set to 0 to
143	disable dcdc5.
144	On A23 / A31 / A33 / A80 / A83T / R40 boards dcdc5 is VCC-DRAM and
145	should be 1.5V, 1.35V if DDR3L is used.
146
147config AXP_ALDO1_VOLT
148	int "axp pmic (a)ldo1 voltage"
149	depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
150	default 0 if MACH_SUN6I || MACH_SUN8I_R40
151	default 1800 if MACH_SUN8I_A83T
152	default 3000 if MACH_SUN8I || MACH_SUN9I
153	---help---
154	Set the voltage (mV) to program the axp pmic aldo1 at, set to 0 to
155	disable aldo1.
156	On A31 boards aldo1 is often used to power the wifi module.
157	On A23 / A33 boards aldo1 is used for VCC-IO and should be 3.0V.
158	On A80 boards aldo1 powers the USB hosts and should be 3.0V.
159	On A83T / H8 boards aldo1 is used for MIPI CSI, DSI, HDMI, EFUSE, and
160	should be 1.8V.
161
162config AXP_ALDO2_VOLT
163	int "axp pmic (a)ldo2 voltage"
164	depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
165	default 3000 if AXP152_POWER || AXP209_POWER
166	default 0 if MACH_SUN6I || MACH_SUN9I
167	default 1800 if MACH_SUN8I_A83T
168	default 2500 if MACH_SUN8I
169	---help---
170	Set the voltage (mV) to program the axp pmic aldo2 at, set to 0 to
171	disable aldo2.
172	On A10(s) / A13 / A20 boards aldo2 is AVCC and should be 3.0V.
173	On A31 boards aldo2 is typically unused and should be disabled.
174	On A31 boards aldo2 may be used for LPDDR2 then it should be 1.8V.
175	On A23 / A33 boards aldo2 is used for VDD-DLL and should be 2.5V.
176	On A80 boards aldo2 powers PB pingroup and camera IO and can be left off.
177	On A83T / H8 boards aldo2 powers VDD-DLL, VCC18-PLL, CPVDD, VDD18-ADC,
178	LPDDR2, and the codec. It should be 1.8V.
179
180config AXP_ALDO3_VOLT
181	int "axp pmic (a)ldo3 voltage"
182	depends on AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
183	default 0 if AXP209_POWER || MACH_SUN9I
184	default 3000 if MACH_SUN6I || MACH_SUN8I
185	---help---
186	Set the voltage (mV) to program the axp pmic aldo3 at, set to 0 to
187	disable aldo3.
188	On A10(s) / A13 / A20 boards aldo3 should be 2.8V.
189	On A23 / A31 / A33 / R40 boards aldo3 is VCC-PLL and AVCC and should
190	be 3.0V.
191	On A80 boards aldo3 is normally not used.
192	On A83T / H8 boards aldo3 is AVCC, VCC-PL, and VCC-LED, and should be
193	3.0V.
194
195config AXP_ALDO4_VOLT
196	int "axp pmic (a)ldo4 voltage"
197	depends on AXP209_POWER
198	default 0 if AXP209_POWER
199	---help---
200	Set the voltage (mV) to program the axp pmic aldo4 at, set to 0 to
201	disable aldo4.
202	On A10(s) / A13 / A20 boards aldo4 should be 2.8V.
203
204config AXP_DLDO1_VOLT
205	int "axp pmic dldo1 voltage"
206	depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
207	default 0
208	---help---
209	Set the voltage (mV) to program the axp pmic dldo1 at, set to 0 to
210	disable dldo1. On sun6i (A31) boards with ethernet dldo1 is often used
211	to power the ethernet phy. On A23, A33 and A80 boards this is often
212	used to power the wifi.
213
214config AXP_DLDO2_VOLT
215	int "axp pmic dldo2 voltage"
216	depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
217	default 3000 if MACH_SUN9I
218	default 0
219	---help---
220	Set the voltage (mV) to program the axp pmic dldo2 at, set to 0 to
221	disable dldo2.
222	On A80 boards dldo2 normally powers the PL pins and should be 3.0V.
223
224config AXP_DLDO3_VOLT
225	int "axp pmic dldo3 voltage"
226	depends on AXP221_POWER || AXP818_POWER
227	default 0
228	---help---
229	Set the voltage (mV) to program the axp pmic dldo3 at, set to 0 to
230	disable dldo3.
231
232config AXP_DLDO4_VOLT
233	int "axp pmic dldo4 voltage"
234	depends on AXP221_POWER || AXP818_POWER
235	default 0
236	---help---
237	Set the voltage (mV) to program the axp pmic dldo4 at, set to 0 to
238	disable dldo4.
239
240config AXP_ELDO1_VOLT
241	int "axp pmic eldo1 voltage"
242	depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
243	default 0
244	---help---
245	Set the voltage (mV) to program the axp pmic eldo1 at, set to 0 to
246	disable eldo1.
247
248config AXP_ELDO2_VOLT
249	int "axp pmic eldo2 voltage"
250	depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
251	default 0
252	---help---
253	Set the voltage (mV) to program the axp pmic eldo2 at, set to 0 to
254	disable eldo2.
255
256config AXP_ELDO3_VOLT
257	int "axp pmic eldo3 voltage"
258	depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
259	default 3000 if MACH_SUN9I
260	default 0
261	---help---
262	Set the voltage (mV) to program the axp pmic eldo3 at, set to 0 to
263	disable eldo3. On some A31(s) tablets it might be used to supply
264	1.2V for the SSD2828 chip (converter of parallel LCD interface
265	into MIPI DSI).
266	On A80 boards it powers the PM pingroup and should be 3.0V.
267
268config AXP_FLDO1_VOLT
269	int "axp pmic fldo1 voltage"
270	depends on AXP818_POWER
271	default 0 if MACH_SUN8I_A83T
272	---help---
273	Set the voltage (mV) to program the axp pmic fldo1 at, set to 0 to
274	disable fldo1.
275	On A83T / H8 boards fldo1 is VCC-HSIC and should be 1.2V if HSIC is
276	used.
277
278config AXP_FLDO2_VOLT
279	int "axp pmic fldo2 voltage"
280	depends on AXP818_POWER
281	default 900 if MACH_SUN8I_A83T
282	---help---
283	Set the voltage (mV) to program the axp pmic fldo2 at, set to 0 to
284	disable fldo2.
285	On A83T / H8 boards fldo2 is VCC-CPUS and should be 0.9V.
286
287config AXP_FLDO3_VOLT
288	int "axp pmic fldo3 voltage"
289	depends on AXP818_POWER
290	default 0
291	---help---
292	Set the voltage (mV) to program the axp pmic fldo3 at, set to 0 to
293	disable fldo3.
294
295config AXP_SW_ON
296	bool "axp pmic sw on"
297	depends on AXP809_POWER || AXP818_POWER
298	default n
299	---help---
300	Enable to turn on axp pmic sw.
301
302config SY8106A_VOUT1_VOLT
303	int "SY8106A pmic VOUT1 voltage"
304	depends on SY8106A_POWER
305	default 1200
306	---help---
307	Set the voltage (mV) to program the SY8106A pmic VOUT1. This
308	is typically used to power the VDD-CPU and should be 1200mV.
309	Values can range from 680mV till 1950mV.
310
311config TWL4030_POWER
312	depends on OMAP34XX
313	bool "Enable driver for TI TWL4030 power management chip"
314	imply CMD_POWEROFF
315	---help---
316	The TWL4030 in a combination audio CODEC/power management with
317	GPIO and it is commonly used with the OMAP3 family of processors
318
319endmenu
320