xref: /openbmc/u-boot/drivers/power/Kconfig (revision d9e268ed)
1menu "Power"
2
3source "drivers/power/domain/Kconfig"
4
5source "drivers/power/pmic/Kconfig"
6
7source "drivers/power/regulator/Kconfig"
8
9choice
10	prompt "Select Sunxi PMIC Variant"
11	depends on ARCH_SUNXI
12	default AXP209_POWER if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
13	default AXP221_POWER if MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33
14	default AXP818_POWER if MACH_SUN8I_A83T
15	default SUNXI_NO_PMIC if MACH_SUN8I_H3 || MACH_SUN50I
16
17config SUNXI_NO_PMIC
18	bool "board without a pmic"
19	---help---
20	Select this for boards which do not use a PMIC.
21
22config AXP152_POWER
23	bool "axp152 pmic support"
24	depends on MACH_SUN5I
25	select CMD_POWEROFF
26	---help---
27	Select this to enable support for the axp152 pmic found on most
28	A10s boards.
29
30config AXP209_POWER
31	bool "axp209 pmic support"
32	depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
33	select CMD_POWEROFF
34	---help---
35	Select this to enable support for the axp209 pmic found on most
36	A10, A13 and A20 boards.
37
38config AXP221_POWER
39	bool "axp221 / axp223 pmic support"
40	depends on MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33
41	select CMD_POWEROFF
42	---help---
43	Select this to enable support for the axp221/axp223 pmic found on most
44	A23 and A31 boards.
45
46config AXP809_POWER
47	bool "axp809 pmic support"
48	depends on MACH_SUN9I
49	select CMD_POWEROFF
50	---help---
51	Say y here to enable support for the axp809 pmic found on A80 boards.
52
53config AXP818_POWER
54	bool "axp818 pmic support"
55	depends on MACH_SUN8I_A83T
56	select CMD_POWEROFF
57	---help---
58	Say y here to enable support for the axp818 pmic found on
59	A83T dev board.
60
61config SY8106A_POWER
62	bool "SY8106A pmic support"
63	depends on MACH_SUN8I_H3
64	---help---
65	Select this to enable support for the SY8106A pmic found on some
66	H3 boards.
67
68endchoice
69
70config AXP_DCDC1_VOLT
71	int "axp pmic dcdc1 voltage"
72	depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
73	default 3300 if AXP818_POWER
74	default 3000 if MACH_SUN6I || MACH_SUN8I || MACH_SUN9I
75	---help---
76	Set the voltage (mV) to program the axp pmic dcdc1 at, set to 0 to
77	disable dcdc1. On A23 / A31 / A33 (axp221) boards dcdc1 is used for
78	generic 3.3V IO voltage for external devices like the lcd-panal and
79	sdcard interfaces, etc. On most boards dcdc1 is undervolted to 3.0V to
80	save battery. On A31 devices dcdc1 is also used for VCC-IO. On A83T
81	dcdc1 is used for VCC-IO, nand, usb0, sd , etc. On A80 dcdc1 normally
82	powers some of the pingroups, NAND/eMMC, SD/MMC, and USB OTG.
83
84config AXP_DCDC2_VOLT
85	int "axp pmic dcdc2 voltage"
86	depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
87	default 900 if AXP818_POWER
88	default 1400 if AXP152_POWER || AXP209_POWER
89	default 1200 if MACH_SUN6I
90	default 1100 if MACH_SUN8I
91	default 0 if MACH_SUN9I
92	---help---
93	Set the voltage (mV) to program the axp pmic dcdc2 at, set to 0 to
94	disable dcdc2.
95	On A10(s) / A13 / A20 boards dcdc2 is VDD-CPU and should be 1.4V.
96	On A31 boards dcdc2 is used for VDD-GPU and should be 1.2V.
97	On A23/A33 boards dcdc2 is used for VDD-SYS and should be 1.1V.
98	On A80 boards dcdc2 powers the GPU and can be left off.
99	On A83T boards dcdc2 is used for VDD-CPUA(cluster 0) and should be 0.9V.
100
101config AXP_DCDC3_VOLT
102	int "axp pmic dcdc3 voltage"
103	depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
104	default 900 if AXP809_POWER || AXP818_POWER
105	default 1500 if AXP152_POWER
106	default 1250 if AXP209_POWER
107	default 1200 if MACH_SUN6I || MACH_SUN8I
108	---help---
109	Set the voltage (mV) to program the axp pmic dcdc3 at, set to 0 to
110	disable dcdc3.
111	On A10(s) / A13 / A20 boards with an axp209 dcdc3 is VDD-INT-DLL and
112	should be 1.25V.
113	On A10s boards with an axp152 dcdc3 is VCC-DRAM and should be 1.5V.
114	On A23 / A31 / A33 boards dcdc3 is VDD-CPU and should be 1.2V.
115	On A80 boards dcdc3 is used for VDD-CPUA(cluster 0) and should be 0.9V.
116	On A83T boards dcdc3 is used for VDD-CPUB(cluster 1) and should be 0.9V.
117
118config AXP_DCDC4_VOLT
119	int "axp pmic dcdc4 voltage"
120	depends on AXP152_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
121	default 1250 if AXP152_POWER
122	default 1200 if MACH_SUN6I
123	default 0 if MACH_SUN8I
124	default 900 if MACH_SUN9I
125	---help---
126	Set the voltage (mV) to program the axp pmic dcdc4 at, set to 0 to
127	disable dcdc4.
128	On A10s boards with an axp152 dcdc4 is VDD-INT-DLL and should be 1.25V.
129	On A31 boards dcdc4 is used for VDD-SYS and should be 1.2V.
130	On A23 / A33 boards dcdc4 is unused and should be disabled.
131	On A80 boards dcdc4 powers VDD-SYS, HDMI, USB OTG and should be 0.9V.
132	On A83T boards dcdc4 is used for VDD-GPU.
133
134config AXP_DCDC5_VOLT
135	int "axp pmic dcdc5 voltage"
136	depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
137	default 1500 if MACH_SUN6I || MACH_SUN8I || MACH_SUN9I
138	---help---
139	Set the voltage (mV) to program the axp pmic dcdc5 at, set to 0 to
140	disable dcdc5.
141	On A23 / A31 / A33 / A80 / A83T boards dcdc5 is VCC-DRAM and
142	should be 1.5V, 1.35V if DDR3L is used.
143
144config AXP_ALDO1_VOLT
145	int "axp pmic (a)ldo1 voltage"
146	depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
147	default 0 if MACH_SUN6I
148	default 1800 if MACH_SUN8I_A83T
149	default 3000 if MACH_SUN8I || MACH_SUN9I
150	---help---
151	Set the voltage (mV) to program the axp pmic aldo1 at, set to 0 to
152	disable aldo1.
153	On A31 boards aldo1 is often used to power the wifi module.
154	On A23 / A33 boards aldo1 is used for VCC-IO and should be 3.0V.
155	On A80 boards aldo1 powers the USB hosts and should be 3.0V.
156	On A83T / H8 boards aldo1 is used for MIPI CSI, DSI, HDMI, EFUSE, and
157	should be 1.8V.
158
159config AXP_ALDO2_VOLT
160	int "axp pmic (a)ldo2 voltage"
161	depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
162	default 3000 if AXP152_POWER || AXP209_POWER
163	default 0 if MACH_SUN6I || MACH_SUN9I
164	default 1800 if MACH_SUN8I_A83T
165	default 2500 if MACH_SUN8I
166	---help---
167	Set the voltage (mV) to program the axp pmic aldo2 at, set to 0 to
168	disable aldo2.
169	On A10(s) / A13 / A20 boards aldo2 is AVCC and should be 3.0V.
170	On A31 boards aldo2 is typically unused and should be disabled.
171	On A31 boards aldo2 may be used for LPDDR2 then it should be 1.8V.
172	On A23 / A33 boards aldo2 is used for VDD-DLL and should be 2.5V.
173	On A80 boards aldo2 powers PB pingroup and camera IO and can be left off.
174	On A83T / H8 boards aldo2 powers VDD-DLL, VCC18-PLL, CPVDD, VDD18-ADC,
175	LPDDR2, and the codec. It should be 1.8V.
176
177config AXP_ALDO3_VOLT
178	int "axp pmic (a)ldo3 voltage"
179	depends on AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
180	default 0 if AXP209_POWER || MACH_SUN9I
181	default 3000 if MACH_SUN6I || MACH_SUN8I
182	---help---
183	Set the voltage (mV) to program the axp pmic aldo3 at, set to 0 to
184	disable aldo3.
185	On A10(s) / A13 / A20 boards aldo3 should be 2.8V.
186	On A23 / A31 / A33 boards aldo3 is VCC-PLL and AVCC and should be 3.0V.
187	On A80 boards aldo3 is normally not used.
188	On A83T / H8 boards aldo3 is AVCC, VCC-PL, and VCC-LED, and should be
189	3.0V.
190
191config AXP_ALDO4_VOLT
192	int "axp pmic (a)ldo4 voltage"
193	depends on AXP209_POWER
194	default 0 if AXP209_POWER
195	---help---
196	Set the voltage (mV) to program the axp pmic aldo4 at, set to 0 to
197	disable aldo4.
198	On A10(s) / A13 / A20 boards aldo4 should be 2.8V.
199
200config AXP_DLDO1_VOLT
201	int "axp pmic dldo1 voltage"
202	depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
203	default 0
204	---help---
205	Set the voltage (mV) to program the axp pmic dldo1 at, set to 0 to
206	disable dldo1. On sun6i (A31) boards with ethernet dldo1 is often used
207	to power the ethernet phy. On A23, A33 and A80 boards this is often
208	used to power the wifi.
209
210config AXP_DLDO2_VOLT
211	int "axp pmic dldo2 voltage"
212	depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
213	default 3000 if MACH_SUN9I
214	default 0
215	---help---
216	Set the voltage (mV) to program the axp pmic dldo2 at, set to 0 to
217	disable dldo2.
218	On A80 boards dldo2 normally powers the PL pins and should be 3.0V.
219
220config AXP_DLDO3_VOLT
221	int "axp pmic dldo3 voltage"
222	depends on AXP221_POWER || AXP818_POWER
223	default 0
224	---help---
225	Set the voltage (mV) to program the axp pmic dldo3 at, set to 0 to
226	disable dldo3.
227
228config AXP_DLDO4_VOLT
229	int "axp pmic dldo4 voltage"
230	depends on AXP221_POWER || AXP818_POWER
231	default 0
232	---help---
233	Set the voltage (mV) to program the axp pmic dldo4 at, set to 0 to
234	disable dldo4.
235
236config AXP_ELDO1_VOLT
237	int "axp pmic eldo1 voltage"
238	depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
239	default 0
240	---help---
241	Set the voltage (mV) to program the axp pmic eldo1 at, set to 0 to
242	disable eldo1.
243
244config AXP_ELDO2_VOLT
245	int "axp pmic eldo2 voltage"
246	depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
247	default 0
248	---help---
249	Set the voltage (mV) to program the axp pmic eldo2 at, set to 0 to
250	disable eldo2.
251
252config AXP_ELDO3_VOLT
253	int "axp pmic eldo3 voltage"
254	depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
255	default 3000 if MACH_SUN9I
256	default 0
257	---help---
258	Set the voltage (mV) to program the axp pmic eldo3 at, set to 0 to
259	disable eldo3. On some A31(s) tablets it might be used to supply
260	1.2V for the SSD2828 chip (converter of parallel LCD interface
261	into MIPI DSI).
262	On A80 boards it powers the PM pingroup and should be 3.0V.
263
264config AXP_FLDO1_VOLT
265	int "axp pmic fldo1 voltage"
266	depends on AXP818_POWER
267	default 0 if MACH_SUN8I_A83T
268	---help---
269	Set the voltage (mV) to program the axp pmic fldo1 at, set to 0 to
270	disable fldo1.
271	On A83T / H8 boards fldo1 is VCC-HSIC and should be 1.2V if HSIC is
272	used.
273
274config AXP_FLDO2_VOLT
275	int "axp pmic fldo2 voltage"
276	depends on AXP818_POWER
277	default 900 if MACH_SUN8I_A83T
278	---help---
279	Set the voltage (mV) to program the axp pmic fldo2 at, set to 0 to
280	disable fldo2.
281	On A83T / H8 boards fldo2 is VCC-CPUS and should be 0.9V.
282
283config AXP_FLDO3_VOLT
284	int "axp pmic fldo3 voltage"
285	depends on AXP818_POWER
286	default 0
287	---help---
288	Set the voltage (mV) to program the axp pmic fldo3 at, set to 0 to
289	disable fldo3.
290
291config AXP_SW_ON
292	bool "axp pmic sw on"
293	depends on AXP809_POWER || AXP818_POWER
294	default n
295	---help---
296	Enable to turn on axp pmic sw.
297
298config SY8106A_VOUT1_VOLT
299	int "SY8106A pmic VOUT1 voltage"
300	depends on SY8106A_POWER
301	default 1200
302	---help---
303	Set the voltage (mV) to program the SY8106A pmic VOUT1. This
304	is typically used to power the VDD-CPU and should be 1200mV.
305	Values can range from 680mV till 1950mV.
306
307endmenu
308