xref: /openbmc/u-boot/drivers/power/Kconfig (revision 37523917)
1menu "Power"
2
3source "drivers/power/pmic/Kconfig"
4
5source "drivers/power/regulator/Kconfig"
6
7choice
8	prompt "Select Sunxi PMIC Variant"
9	depends on ARCH_SUNXI
10	default AXP209_POWER if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
11	default AXP221_POWER if MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33
12	default AXP818_POWER if MACH_SUN8I_A83T
13	default SUNXI_NO_PMIC if MACH_SUN8I_H3 || MACH_SUN50I
14
15config SUNXI_NO_PMIC
16	boolean "board without a pmic"
17	---help---
18	Select this for boards which do not use a PMIC.
19
20config AXP152_POWER
21	boolean "axp152 pmic support"
22	depends on MACH_SUN5I
23	select CMD_POWEROFF
24	---help---
25	Select this to enable support for the axp152 pmic found on most
26	A10s boards.
27
28config AXP209_POWER
29	boolean "axp209 pmic support"
30	depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
31	select CMD_POWEROFF
32	---help---
33	Select this to enable support for the axp209 pmic found on most
34	A10, A13 and A20 boards.
35
36config AXP221_POWER
37	boolean "axp221 / axp223 pmic support"
38	depends on MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33
39	select CMD_POWEROFF
40	---help---
41	Select this to enable support for the axp221/axp223 pmic found on most
42	A23 and A31 boards.
43
44config AXP809_POWER
45	boolean "axp809 pmic support"
46	depends on MACH_SUN9I
47	select CMD_POWEROFF
48	---help---
49	Say y here to enable support for the axp809 pmic found on A80 boards.
50
51config AXP818_POWER
52	boolean "axp818 pmic support"
53	depends on MACH_SUN8I_A83T
54	select CMD_POWEROFF
55	---help---
56	Say y here to enable support for the axp818 pmic found on
57	A83T dev board.
58
59config SY8106A_POWER
60	boolean "SY8106A pmic support"
61	depends on MACH_SUN8I_H3
62	---help---
63	Select this to enable support for the SY8106A pmic found on some
64	H3 boards.
65
66endchoice
67
68config AXP_DCDC1_VOLT
69	int "axp pmic dcdc1 voltage"
70	depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
71	default 3300 if AXP818_POWER
72	default 3000 if MACH_SUN6I || MACH_SUN8I || MACH_SUN9I
73	---help---
74	Set the voltage (mV) to program the axp pmic dcdc1 at, set to 0 to
75	disable dcdc1. On A23 / A31 / A33 (axp221) boards dcdc1 is used for
76	generic 3.3V IO voltage for external devices like the lcd-panal and
77	sdcard interfaces, etc. On most boards dcdc1 is undervolted to 3.0V to
78	save battery. On A31 devices dcdc1 is also used for VCC-IO. On A83T
79	dcdc1 is used for VCC-IO, nand, usb0, sd , etc. On A80 dcdc1 normally
80	powers some of the pingroups, NAND/eMMC, SD/MMC, and USB OTG.
81
82config AXP_DCDC2_VOLT
83	int "axp pmic dcdc2 voltage"
84	depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
85	default 900 if AXP818_POWER
86	default 1400 if AXP152_POWER || AXP209_POWER
87	default 1200 if MACH_SUN6I
88	default 1100 if MACH_SUN8I
89	default 0 if MACH_SUN9I
90	---help---
91	Set the voltage (mV) to program the axp pmic dcdc2 at, set to 0 to
92	disable dcdc2.
93	On A10(s) / A13 / A20 boards dcdc2 is VDD-CPU and should be 1.4V.
94	On A31 boards dcdc2 is used for VDD-GPU and should be 1.2V.
95	On A23/A33 boards dcdc2 is used for VDD-SYS and should be 1.1V.
96	On A80 boards dcdc2 powers the GPU and can be left off.
97	On A83T boards dcdc2 is used for VDD-CPUA(cluster 0) and should be 0.9V.
98
99config AXP_DCDC3_VOLT
100	int "axp pmic dcdc3 voltage"
101	depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
102	default 900 if AXP809_POWER || AXP818_POWER
103	default 1500 if AXP152_POWER
104	default 1250 if AXP209_POWER
105	default 1200 if MACH_SUN6I || MACH_SUN8I
106	---help---
107	Set the voltage (mV) to program the axp pmic dcdc3 at, set to 0 to
108	disable dcdc3.
109	On A10(s) / A13 / A20 boards with an axp209 dcdc3 is VDD-INT-DLL and
110	should be 1.25V.
111	On A10s boards with an axp152 dcdc3 is VCC-DRAM and should be 1.5V.
112	On A23 / A31 / A33 boards dcdc3 is VDD-CPU and should be 1.2V.
113	On A80 boards dcdc3 is used for VDD-CPUA(cluster 0) and should be 0.9V.
114	On A83T boards dcdc3 is used for VDD-CPUB(cluster 1) and should be 0.9V.
115
116config AXP_DCDC4_VOLT
117	int "axp pmic dcdc4 voltage"
118	depends on AXP152_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
119	default 1250 if AXP152_POWER
120	default 1200 if MACH_SUN6I
121	default 0 if MACH_SUN8I
122	default 900 if MACH_SUN9I
123	---help---
124	Set the voltage (mV) to program the axp pmic dcdc4 at, set to 0 to
125	disable dcdc4.
126	On A10s boards with an axp152 dcdc4 is VDD-INT-DLL and should be 1.25V.
127	On A31 boards dcdc4 is used for VDD-SYS and should be 1.2V.
128	On A23 / A33 boards dcdc4 is unused and should be disabled.
129	On A80 boards dcdc4 powers VDD-SYS, HDMI, USB OTG and should be 0.9V.
130	On A83T boards dcdc4 is used for VDD-GPU.
131
132config AXP_DCDC5_VOLT
133	int "axp pmic dcdc5 voltage"
134	depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
135	default 1500 if MACH_SUN6I || MACH_SUN8I || MACH_SUN9I
136	---help---
137	Set the voltage (mV) to program the axp pmic dcdc5 at, set to 0 to
138	disable dcdc5.
139	On A23 / A31 / A33 / A80 / A83T boards dcdc5 is VCC-DRAM and
140	should be 1.5V, 1.35V if DDR3L is used.
141
142config AXP_ALDO1_VOLT
143	int "axp pmic (a)ldo1 voltage"
144	depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
145	default 0 if MACH_SUN6I
146	default 1800 if MACH_SUN8I_A83T
147	default 3000 if MACH_SUN8I || MACH_SUN9I
148	---help---
149	Set the voltage (mV) to program the axp pmic aldo1 at, set to 0 to
150	disable aldo1.
151	On A31 boards aldo1 is often used to power the wifi module.
152	On A23 / A33 boards aldo1 is used for VCC-IO and should be 3.0V.
153	On A80 boards aldo1 powers the USB hosts and should be 3.0V.
154	On A83T / H8 boards aldo1 is used for MIPI CSI, DSI, HDMI, EFUSE, and
155	should be 1.8V.
156
157config AXP_ALDO2_VOLT
158	int "axp pmic (a)ldo2 voltage"
159	depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
160	default 3000 if AXP152_POWER || AXP209_POWER
161	default 0 if MACH_SUN6I || MACH_SUN9I
162	default 1800 if MACH_SUN8I_A83T
163	default 2500 if MACH_SUN8I
164	---help---
165	Set the voltage (mV) to program the axp pmic aldo2 at, set to 0 to
166	disable aldo2.
167	On A10(s) / A13 / A20 boards aldo2 is AVCC and should be 3.0V.
168	On A31 boards aldo2 is typically unused and should be disabled.
169	On A31 boards aldo2 may be used for LPDDR2 then it should be 1.8V.
170	On A23 / A33 boards aldo2 is used for VDD-DLL and should be 2.5V.
171	On A80 boards aldo2 powers PB pingroup and camera IO and can be left off.
172	On A83T / H8 boards aldo2 powers VDD-DLL, VCC18-PLL, CPVDD, VDD18-ADC,
173	LPDDR2, and the codec. It should be 1.8V.
174
175config AXP_ALDO3_VOLT
176	int "axp pmic (a)ldo3 voltage"
177	depends on AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
178	default 0 if AXP209_POWER || MACH_SUN9I
179	default 3000 if MACH_SUN6I || MACH_SUN8I
180	---help---
181	Set the voltage (mV) to program the axp pmic aldo3 at, set to 0 to
182	disable aldo3.
183	On A10(s) / A13 / A20 boards aldo3 should be 2.8V.
184	On A23 / A31 / A33 boards aldo3 is VCC-PLL and AVCC and should be 3.0V.
185	On A80 boards aldo3 is normally not used.
186	On A83T / H8 boards aldo3 is AVCC, VCC-PL, and VCC-LED, and should be
187	3.0V.
188
189config AXP_ALDO4_VOLT
190	int "axp pmic (a)ldo4 voltage"
191	depends on AXP209_POWER
192	default 0 if AXP209_POWER
193	---help---
194	Set the voltage (mV) to program the axp pmic aldo4 at, set to 0 to
195	disable aldo4.
196	On A10(s) / A13 / A20 boards aldo4 should be 2.8V.
197
198config AXP_DLDO1_VOLT
199	int "axp pmic dldo1 voltage"
200	depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
201	default 0
202	---help---
203	Set the voltage (mV) to program the axp pmic dldo1 at, set to 0 to
204	disable dldo1. On sun6i (A31) boards with ethernet dldo1 is often used
205	to power the ethernet phy. On A23, A33 and A80 boards this is often
206	used to power the wifi.
207
208config AXP_DLDO2_VOLT
209	int "axp pmic dldo2 voltage"
210	depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
211	default 3000 if MACH_SUN9I
212	default 0
213	---help---
214	Set the voltage (mV) to program the axp pmic dldo2 at, set to 0 to
215	disable dldo2.
216	On A80 boards dldo2 normally powers the PL pins and should be 3.0V.
217
218config AXP_DLDO3_VOLT
219	int "axp pmic dldo3 voltage"
220	depends on AXP221_POWER || AXP818_POWER
221	default 0
222	---help---
223	Set the voltage (mV) to program the axp pmic dldo3 at, set to 0 to
224	disable dldo3.
225
226config AXP_DLDO4_VOLT
227	int "axp pmic dldo4 voltage"
228	depends on AXP221_POWER || AXP818_POWER
229	default 0
230	---help---
231	Set the voltage (mV) to program the axp pmic dldo4 at, set to 0 to
232	disable dldo4.
233
234config AXP_ELDO1_VOLT
235	int "axp pmic eldo1 voltage"
236	depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
237	default 0
238	---help---
239	Set the voltage (mV) to program the axp pmic eldo1 at, set to 0 to
240	disable eldo1.
241
242config AXP_ELDO2_VOLT
243	int "axp pmic eldo2 voltage"
244	depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
245	default 0
246	---help---
247	Set the voltage (mV) to program the axp pmic eldo2 at, set to 0 to
248	disable eldo2.
249
250config AXP_ELDO3_VOLT
251	int "axp pmic eldo3 voltage"
252	depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
253	default 3000 if MACH_SUN9I
254	default 0
255	---help---
256	Set the voltage (mV) to program the axp pmic eldo3 at, set to 0 to
257	disable eldo3. On some A31(s) tablets it might be used to supply
258	1.2V for the SSD2828 chip (converter of parallel LCD interface
259	into MIPI DSI).
260	On A80 boards it powers the PM pingroup and should be 3.0V.
261
262config AXP_FLDO1_VOLT
263	int "axp pmic fldo1 voltage"
264	depends on AXP818_POWER
265	default 0 if MACH_SUN8I_A83T
266	---help---
267	Set the voltage (mV) to program the axp pmic fldo1 at, set to 0 to
268	disable fldo1.
269	On A83T / H8 boards fldo1 is VCC-HSIC and should be 1.2V if HSIC is
270	used.
271
272config AXP_FLDO2_VOLT
273	int "axp pmic fldo2 voltage"
274	depends on AXP818_POWER
275	default 900 if MACH_SUN8I_A83T
276	---help---
277	Set the voltage (mV) to program the axp pmic fldo2 at, set to 0 to
278	disable fldo2.
279	On A83T / H8 boards fldo2 is VCC-CPUS and should be 0.9V.
280
281config AXP_FLDO3_VOLT
282	int "axp pmic fldo3 voltage"
283	depends on AXP818_POWER
284	default 0
285	---help---
286	Set the voltage (mV) to program the axp pmic fldo3 at, set to 0 to
287	disable fldo3.
288
289config AXP_SW_ON
290	bool "axp pmic sw on"
291	depends on AXP809_POWER || AXP818_POWER
292	default n
293	---help---
294	Enable to turn on axp pmic sw.
295
296config SY8106A_VOUT1_VOLT
297	int "SY8106A pmic VOUT1 voltage"
298	depends on SY8106A_POWER
299	default 1200
300	---help---
301	Set the voltage (mV) to program the SY8106A pmic VOUT1. This
302	is typically used to power the VDD-CPU and should be 1200mV.
303	Values can range from 680mV till 1950mV.
304
305endmenu
306