1menu "Power" 2 3source "drivers/power/pmic/Kconfig" 4 5source "drivers/power/regulator/Kconfig" 6 7choice 8 prompt "Select Sunxi PMIC Variant" 9 depends on ARCH_SUNXI 10 default AXP209_POWER if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I 11 default AXP221_POWER if MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33 12 default AXP818_POWER if MACH_SUN8I_A83T 13 default SUNXI_NO_PMIC if MACH_SUN8I_H3 || MACH_SUN50I 14 15config SUNXI_NO_PMIC 16 boolean "board without a pmic" 17 ---help--- 18 Select this for boards which do not use a PMIC. 19 20config AXP152_POWER 21 boolean "axp152 pmic support" 22 depends on MACH_SUN5I 23 select CMD_POWEROFF 24 ---help--- 25 Select this to enable support for the axp152 pmic found on most 26 A10s boards. 27 28config AXP209_POWER 29 boolean "axp209 pmic support" 30 depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I 31 select CMD_POWEROFF 32 ---help--- 33 Select this to enable support for the axp209 pmic found on most 34 A10, A13 and A20 boards. 35 36config AXP221_POWER 37 boolean "axp221 / axp223 pmic support" 38 depends on MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33 39 select CMD_POWEROFF 40 ---help--- 41 Select this to enable support for the axp221/axp223 pmic found on most 42 A23 and A31 boards. 43 44config AXP809_POWER 45 boolean "axp809 pmic support" 46 depends on MACH_SUN9I 47 select CMD_POWEROFF 48 ---help--- 49 Say y here to enable support for the axp809 pmic found on A80 boards. 50 51config AXP818_POWER 52 boolean "axp818 pmic support" 53 depends on MACH_SUN8I_A83T 54 select CMD_POWEROFF 55 ---help--- 56 Say y here to enable support for the axp818 pmic found on 57 A83T dev board. 58 59config SY8106A_POWER 60 boolean "SY8106A pmic support" 61 depends on MACH_SUN8I_H3 62 ---help--- 63 Select this to enable support for the SY8106A pmic found on some 64 H3 boards. 65 66endchoice 67 68config AXP_DCDC1_VOLT 69 int "axp pmic dcdc1 voltage" 70 depends on AXP221_POWER || AXP809_POWER || AXP818_POWER 71 default 3300 if AXP818_POWER 72 default 3000 if MACH_SUN6I || MACH_SUN8I || MACH_SUN9I 73 ---help--- 74 Set the voltage (mV) to program the axp pmic dcdc1 at, set to 0 to 75 disable dcdc1. On A23 / A31 / A33 (axp221) boards dcdc1 is used for 76 generic 3.3V IO voltage for external devices like the lcd-panal and 77 sdcard interfaces, etc. On most boards dcdc1 is undervolted to 3.0V to 78 save battery. On A31 devices dcdc1 is also used for VCC-IO. On A83T 79 dcdc1 is used for VCC-IO, nand, usb0, sd , etc. On A80 dcdc1 normally 80 powers some of the pingroups, NAND/eMMC, SD/MMC, and USB OTG. 81 82config AXP_DCDC2_VOLT 83 int "axp pmic dcdc2 voltage" 84 depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER 85 default 900 if AXP818_POWER 86 default 1400 if AXP152_POWER || AXP209_POWER 87 default 1200 if MACH_SUN6I 88 default 1100 if MACH_SUN8I 89 default 0 if MACH_SUN9I 90 ---help--- 91 Set the voltage (mV) to program the axp pmic dcdc2 at, set to 0 to 92 disable dcdc2. 93 On A10(s) / A13 / A20 boards dcdc2 is VDD-CPU and should be 1.4V. 94 On A31 boards dcdc2 is used for VDD-GPU and should be 1.2V. 95 On A23/A33 boards dcdc2 is used for VDD-SYS and should be 1.1V. 96 On A80 boards dcdc2 powers the GPU and can be left off. 97 On A83T boards dcdc2 is used for VDD-CPUA(cluster 0) and should be 0.9V. 98 99config AXP_DCDC3_VOLT 100 int "axp pmic dcdc3 voltage" 101 depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER 102 default 900 if AXP809_POWER || AXP818_POWER 103 default 1500 if AXP152_POWER 104 default 1250 if AXP209_POWER 105 default 1200 if MACH_SUN6I || MACH_SUN8I 106 ---help--- 107 Set the voltage (mV) to program the axp pmic dcdc3 at, set to 0 to 108 disable dcdc3. 109 On A10(s) / A13 / A20 boards with an axp209 dcdc3 is VDD-INT-DLL and 110 should be 1.25V. 111 On A10s boards with an axp152 dcdc3 is VCC-DRAM and should be 1.5V. 112 On A23 / A31 / A33 boards dcdc3 is VDD-CPU and should be 1.2V. 113 On A80 boards dcdc3 is used for VDD-CPUA(cluster 0) and should be 0.9V. 114 On A83T boards dcdc3 is used for VDD-CPUB(cluster 1) and should be 0.9V. 115 116config AXP_DCDC4_VOLT 117 int "axp pmic dcdc4 voltage" 118 depends on AXP152_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER 119 default 1250 if AXP152_POWER 120 default 1200 if MACH_SUN6I 121 default 0 if MACH_SUN8I 122 default 900 if MACH_SUN9I 123 ---help--- 124 Set the voltage (mV) to program the axp pmic dcdc4 at, set to 0 to 125 disable dcdc4. 126 On A10s boards with an axp152 dcdc4 is VDD-INT-DLL and should be 1.25V. 127 On A31 boards dcdc4 is used for VDD-SYS and should be 1.2V. 128 On A23 / A33 boards dcdc4 is unused and should be disabled. 129 On A80 boards dcdc4 powers VDD-SYS, HDMI, USB OTG and should be 0.9V. 130 On A83T boards dcdc4 is used for VDD-GPU. 131 132config AXP_DCDC5_VOLT 133 int "axp pmic dcdc5 voltage" 134 depends on AXP221_POWER || AXP809_POWER || AXP818_POWER 135 default 1500 if MACH_SUN6I || MACH_SUN8I || MACH_SUN9I 136 ---help--- 137 Set the voltage (mV) to program the axp pmic dcdc5 at, set to 0 to 138 disable dcdc5. 139 On A23 / A31 / A33 / A80 / A83T boards dcdc5 is VCC-DRAM and 140 should be 1.5V, 1.35V if DDR3L is used. 141 142config AXP_ALDO1_VOLT 143 int "axp pmic (a)ldo1 voltage" 144 depends on AXP221_POWER || AXP809_POWER || AXP818_POWER 145 default 0 if MACH_SUN6I 146 default 1800 if MACH_SUN8I_A83T 147 default 3000 if MACH_SUN8I || MACH_SUN9I 148 ---help--- 149 Set the voltage (mV) to program the axp pmic aldo1 at, set to 0 to 150 disable aldo1. 151 On A31 boards aldo1 is often used to power the wifi module. 152 On A23 / A33 boards aldo1 is used for VCC-IO and should be 3.0V. 153 On A80 boards aldo1 powers the USB hosts and should be 3.0V. 154 On A83T / H8 boards aldo1 is used for MIPI CSI, DSI, HDMI, EFUSE, and 155 should be 1.8V. 156 157config AXP_ALDO2_VOLT 158 int "axp pmic (a)ldo2 voltage" 159 depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER 160 default 3000 if AXP152_POWER || AXP209_POWER 161 default 0 if MACH_SUN6I || MACH_SUN9I 162 default 1800 if MACH_SUN8I_A83T 163 default 2500 if MACH_SUN8I 164 ---help--- 165 Set the voltage (mV) to program the axp pmic aldo2 at, set to 0 to 166 disable aldo2. 167 On A10(s) / A13 / A20 boards aldo2 is AVCC and should be 3.0V. 168 On A31 boards aldo2 is typically unused and should be disabled. 169 On A31 boards aldo2 may be used for LPDDR2 then it should be 1.8V. 170 On A23 / A33 boards aldo2 is used for VDD-DLL and should be 2.5V. 171 On A80 boards aldo2 powers PB pingroup and camera IO and can be left off. 172 On A83T / H8 boards aldo2 powers VDD-DLL, VCC18-PLL, CPVDD, VDD18-ADC, 173 LPDDR2, and the codec. It should be 1.8V. 174 175config AXP_ALDO3_VOLT 176 int "axp pmic (a)ldo3 voltage" 177 depends on AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER 178 default 0 if AXP209_POWER || MACH_SUN9I 179 default 3000 if MACH_SUN6I || MACH_SUN8I 180 ---help--- 181 Set the voltage (mV) to program the axp pmic aldo3 at, set to 0 to 182 disable aldo3. 183 On A10(s) / A13 / A20 boards aldo3 should be 2.8V. 184 On A23 / A31 / A33 boards aldo3 is VCC-PLL and AVCC and should be 3.0V. 185 On A80 boards aldo3 is normally not used. 186 On A83T / H8 boards aldo3 is AVCC, VCC-PL, and VCC-LED, and should be 187 3.0V. 188 189config AXP_ALDO4_VOLT 190 int "axp pmic (a)ldo4 voltage" 191 depends on AXP209_POWER 192 default 0 if AXP209_POWER 193 ---help--- 194 Set the voltage (mV) to program the axp pmic aldo4 at, set to 0 to 195 disable aldo4. 196 On A10(s) / A13 / A20 boards aldo4 should be 2.8V. 197 198config AXP_DLDO1_VOLT 199 int "axp pmic dldo1 voltage" 200 depends on AXP221_POWER || AXP809_POWER || AXP818_POWER 201 default 0 202 ---help--- 203 Set the voltage (mV) to program the axp pmic dldo1 at, set to 0 to 204 disable dldo1. On sun6i (A31) boards with ethernet dldo1 is often used 205 to power the ethernet phy. On A23, A33 and A80 boards this is often 206 used to power the wifi. 207 208config AXP_DLDO2_VOLT 209 int "axp pmic dldo2 voltage" 210 depends on AXP221_POWER || AXP809_POWER || AXP818_POWER 211 default 3000 if MACH_SUN9I 212 default 0 213 ---help--- 214 Set the voltage (mV) to program the axp pmic dldo2 at, set to 0 to 215 disable dldo2. 216 On A80 boards dldo2 normally powers the PL pins and should be 3.0V. 217 218config AXP_DLDO3_VOLT 219 int "axp pmic dldo3 voltage" 220 depends on AXP221_POWER || AXP818_POWER 221 default 0 222 ---help--- 223 Set the voltage (mV) to program the axp pmic dldo3 at, set to 0 to 224 disable dldo3. 225 226config AXP_DLDO4_VOLT 227 int "axp pmic dldo4 voltage" 228 depends on AXP221_POWER || AXP818_POWER 229 default 0 230 ---help--- 231 Set the voltage (mV) to program the axp pmic dldo4 at, set to 0 to 232 disable dldo4. 233 234config AXP_ELDO1_VOLT 235 int "axp pmic eldo1 voltage" 236 depends on AXP221_POWER || AXP809_POWER || AXP818_POWER 237 default 0 238 ---help--- 239 Set the voltage (mV) to program the axp pmic eldo1 at, set to 0 to 240 disable eldo1. 241 242config AXP_ELDO2_VOLT 243 int "axp pmic eldo2 voltage" 244 depends on AXP221_POWER || AXP809_POWER || AXP818_POWER 245 default 0 246 ---help--- 247 Set the voltage (mV) to program the axp pmic eldo2 at, set to 0 to 248 disable eldo2. 249 250config AXP_ELDO3_VOLT 251 int "axp pmic eldo3 voltage" 252 depends on AXP221_POWER || AXP809_POWER || AXP818_POWER 253 default 3000 if MACH_SUN9I 254 default 0 255 ---help--- 256 Set the voltage (mV) to program the axp pmic eldo3 at, set to 0 to 257 disable eldo3. On some A31(s) tablets it might be used to supply 258 1.2V for the SSD2828 chip (converter of parallel LCD interface 259 into MIPI DSI). 260 On A80 boards it powers the PM pingroup and should be 3.0V. 261 262config AXP_FLDO1_VOLT 263 int "axp pmic fldo1 voltage" 264 depends on AXP818_POWER 265 default 0 if MACH_SUN8I_A83T 266 ---help--- 267 Set the voltage (mV) to program the axp pmic fldo1 at, set to 0 to 268 disable fldo1. 269 On A83T / H8 boards fldo1 is VCC-HSIC and should be 1.2V if HSIC is 270 used. 271 272config AXP_FLDO2_VOLT 273 int "axp pmic fldo2 voltage" 274 depends on AXP818_POWER 275 default 900 if MACH_SUN8I_A83T 276 ---help--- 277 Set the voltage (mV) to program the axp pmic fldo2 at, set to 0 to 278 disable fldo2. 279 On A83T / H8 boards fldo2 is VCC-CPUS and should be 0.9V. 280 281config AXP_FLDO3_VOLT 282 int "axp pmic fldo3 voltage" 283 depends on AXP818_POWER 284 default 0 285 ---help--- 286 Set the voltage (mV) to program the axp pmic fldo3 at, set to 0 to 287 disable fldo3. 288 289config AXP_SW_ON 290 bool "axp pmic sw on" 291 depends on AXP809_POWER || AXP818_POWER 292 default n 293 ---help--- 294 Enable to turn on axp pmic sw. 295 296config SY8106A_VOUT1_VOLT 297 int "SY8106A pmic VOUT1 voltage" 298 depends on SY8106A_POWER 299 default 1200 300 ---help--- 301 Set the voltage (mV) to program the SY8106A pmic VOUT1. This 302 is typically used to power the VDD-CPU and should be 1200mV. 303 Values can range from 680mV till 1950mV. 304 305endmenu 306