xref: /openbmc/u-boot/drivers/net/zynq_gem.c (revision f77d4410)
1 // SPDX-License-Identifier: GPL-2.0+
2 /*
3  * (C) Copyright 2011 Michal Simek
4  *
5  * Michal SIMEK <monstr@monstr.eu>
6  *
7  * Based on Xilinx gmac driver:
8  * (C) Copyright 2011 Xilinx
9  */
10 
11 #include <clk.h>
12 #include <common.h>
13 #include <dm.h>
14 #include <net.h>
15 #include <netdev.h>
16 #include <config.h>
17 #include <console.h>
18 #include <malloc.h>
19 #include <asm/io.h>
20 #include <phy.h>
21 #include <miiphy.h>
22 #include <wait_bit.h>
23 #include <watchdog.h>
24 #include <asm/system.h>
25 #include <asm/arch/hardware.h>
26 #include <asm/arch/sys_proto.h>
27 #include <linux/errno.h>
28 
29 DECLARE_GLOBAL_DATA_PTR;
30 
31 /* Bit/mask specification */
32 #define ZYNQ_GEM_PHYMNTNC_OP_MASK	0x40020000 /* operation mask bits */
33 #define ZYNQ_GEM_PHYMNTNC_OP_R_MASK	0x20000000 /* read operation */
34 #define ZYNQ_GEM_PHYMNTNC_OP_W_MASK	0x10000000 /* write operation */
35 #define ZYNQ_GEM_PHYMNTNC_PHYAD_SHIFT_MASK	23 /* Shift bits for PHYAD */
36 #define ZYNQ_GEM_PHYMNTNC_PHREG_SHIFT_MASK	18 /* Shift bits for PHREG */
37 
38 #define ZYNQ_GEM_RXBUF_EOF_MASK		0x00008000 /* End of frame. */
39 #define ZYNQ_GEM_RXBUF_SOF_MASK		0x00004000 /* Start of frame. */
40 #define ZYNQ_GEM_RXBUF_LEN_MASK		0x00003FFF /* Mask for length field */
41 
42 #define ZYNQ_GEM_RXBUF_WRAP_MASK	0x00000002 /* Wrap bit, last BD */
43 #define ZYNQ_GEM_RXBUF_NEW_MASK		0x00000001 /* Used bit.. */
44 #define ZYNQ_GEM_RXBUF_ADD_MASK		0xFFFFFFFC /* Mask for address */
45 
46 /* Wrap bit, last descriptor */
47 #define ZYNQ_GEM_TXBUF_WRAP_MASK	0x40000000
48 #define ZYNQ_GEM_TXBUF_LAST_MASK	0x00008000 /* Last buffer */
49 #define ZYNQ_GEM_TXBUF_USED_MASK	0x80000000 /* Used by Hw */
50 
51 #define ZYNQ_GEM_NWCTRL_TXEN_MASK	0x00000008 /* Enable transmit */
52 #define ZYNQ_GEM_NWCTRL_RXEN_MASK	0x00000004 /* Enable receive */
53 #define ZYNQ_GEM_NWCTRL_MDEN_MASK	0x00000010 /* Enable MDIO port */
54 #define ZYNQ_GEM_NWCTRL_STARTTX_MASK	0x00000200 /* Start tx (tx_go) */
55 
56 #define ZYNQ_GEM_NWCFG_SPEED100		0x00000001 /* 100 Mbps operation */
57 #define ZYNQ_GEM_NWCFG_SPEED1000	0x00000400 /* 1Gbps operation */
58 #define ZYNQ_GEM_NWCFG_FDEN		0x00000002 /* Full Duplex mode */
59 #define ZYNQ_GEM_NWCFG_FSREM		0x00020000 /* FCS removal */
60 #define ZYNQ_GEM_NWCFG_SGMII_ENBL	0x08000000 /* SGMII Enable */
61 #define ZYNQ_GEM_NWCFG_PCS_SEL		0x00000800 /* PCS select */
62 #ifdef CONFIG_ARM64
63 #define ZYNQ_GEM_NWCFG_MDCCLKDIV	0x00100000 /* Div pclk by 64, max 160MHz */
64 #else
65 #define ZYNQ_GEM_NWCFG_MDCCLKDIV	0x000c0000 /* Div pclk by 48, max 120MHz */
66 #endif
67 
68 #ifdef CONFIG_ARM64
69 # define ZYNQ_GEM_DBUS_WIDTH	(1 << 21) /* 64 bit bus */
70 #else
71 # define ZYNQ_GEM_DBUS_WIDTH	(0 << 21) /* 32 bit bus */
72 #endif
73 
74 #define ZYNQ_GEM_NWCFG_INIT		(ZYNQ_GEM_DBUS_WIDTH | \
75 					ZYNQ_GEM_NWCFG_FDEN | \
76 					ZYNQ_GEM_NWCFG_FSREM | \
77 					ZYNQ_GEM_NWCFG_MDCCLKDIV)
78 
79 #define ZYNQ_GEM_NWSR_MDIOIDLE_MASK	0x00000004 /* PHY management idle */
80 
81 #define ZYNQ_GEM_DMACR_BLENGTH		0x00000004 /* INCR4 AHB bursts */
82 /* Use full configured addressable space (8 Kb) */
83 #define ZYNQ_GEM_DMACR_RXSIZE		0x00000300
84 /* Use full configured addressable space (4 Kb) */
85 #define ZYNQ_GEM_DMACR_TXSIZE		0x00000400
86 /* Set with binary 00011000 to use 1536 byte(1*max length frame/buffer) */
87 #define ZYNQ_GEM_DMACR_RXBUF		0x00180000
88 
89 #define ZYNQ_GEM_DMACR_INIT		(ZYNQ_GEM_DMACR_BLENGTH | \
90 					ZYNQ_GEM_DMACR_RXSIZE | \
91 					ZYNQ_GEM_DMACR_TXSIZE | \
92 					ZYNQ_GEM_DMACR_RXBUF)
93 
94 #define ZYNQ_GEM_TSR_DONE		0x00000020 /* Tx done mask */
95 
96 #define ZYNQ_GEM_PCS_CTL_ANEG_ENBL	0x1000
97 
98 /* Use MII register 1 (MII status register) to detect PHY */
99 #define PHY_DETECT_REG  1
100 
101 /* Mask used to verify certain PHY features (or register contents)
102  * in the register above:
103  *  0x1000: 10Mbps full duplex support
104  *  0x0800: 10Mbps half duplex support
105  *  0x0008: Auto-negotiation support
106  */
107 #define PHY_DETECT_MASK 0x1808
108 
109 /* TX BD status masks */
110 #define ZYNQ_GEM_TXBUF_FRMLEN_MASK	0x000007ff
111 #define ZYNQ_GEM_TXBUF_EXHAUSTED	0x08000000
112 #define ZYNQ_GEM_TXBUF_UNDERRUN		0x10000000
113 
114 /* Clock frequencies for different speeds */
115 #define ZYNQ_GEM_FREQUENCY_10	2500000UL
116 #define ZYNQ_GEM_FREQUENCY_100	25000000UL
117 #define ZYNQ_GEM_FREQUENCY_1000	125000000UL
118 
119 /* Device registers */
120 struct zynq_gem_regs {
121 	u32 nwctrl; /* 0x0 - Network Control reg */
122 	u32 nwcfg; /* 0x4 - Network Config reg */
123 	u32 nwsr; /* 0x8 - Network Status reg */
124 	u32 reserved1;
125 	u32 dmacr; /* 0x10 - DMA Control reg */
126 	u32 txsr; /* 0x14 - TX Status reg */
127 	u32 rxqbase; /* 0x18 - RX Q Base address reg */
128 	u32 txqbase; /* 0x1c - TX Q Base address reg */
129 	u32 rxsr; /* 0x20 - RX Status reg */
130 	u32 reserved2[2];
131 	u32 idr; /* 0x2c - Interrupt Disable reg */
132 	u32 reserved3;
133 	u32 phymntnc; /* 0x34 - Phy Maintaince reg */
134 	u32 reserved4[18];
135 	u32 hashl; /* 0x80 - Hash Low address reg */
136 	u32 hashh; /* 0x84 - Hash High address reg */
137 #define LADDR_LOW	0
138 #define LADDR_HIGH	1
139 	u32 laddr[4][LADDR_HIGH + 1]; /* 0x8c - Specific1 addr low/high reg */
140 	u32 match[4]; /* 0xa8 - Type ID1 Match reg */
141 	u32 reserved6[18];
142 #define STAT_SIZE	44
143 	u32 stat[STAT_SIZE]; /* 0x100 - Octects transmitted Low reg */
144 	u32 reserved9[20];
145 	u32 pcscntrl;
146 	u32 reserved7[143];
147 	u32 transmit_q1_ptr; /* 0x440 - Transmit priority queue 1 */
148 	u32 reserved8[15];
149 	u32 receive_q1_ptr; /* 0x480 - Receive priority queue 1 */
150 };
151 
152 /* BD descriptors */
153 struct emac_bd {
154 	u32 addr; /* Next descriptor pointer */
155 	u32 status;
156 };
157 
158 #define RX_BUF 32
159 /* Page table entries are set to 1MB, or multiples of 1MB
160  * (not < 1MB). driver uses less bd's so use 1MB bdspace.
161  */
162 #define BD_SPACE	0x100000
163 /* BD separation space */
164 #define BD_SEPRN_SPACE	(RX_BUF * sizeof(struct emac_bd))
165 
166 /* Setup the first free TX descriptor */
167 #define TX_FREE_DESC	2
168 
169 /* Initialized, rxbd_current, rx_first_buf must be 0 after init */
170 struct zynq_gem_priv {
171 	struct emac_bd *tx_bd;
172 	struct emac_bd *rx_bd;
173 	char *rxbuffers;
174 	u32 rxbd_current;
175 	u32 rx_first_buf;
176 	int phyaddr;
177 	int init;
178 	struct zynq_gem_regs *iobase;
179 	phy_interface_t interface;
180 	struct phy_device *phydev;
181 	ofnode phy_of_node;
182 	struct mii_dev *bus;
183 	struct clk clk;
184 	u32 max_speed;
185 	bool int_pcs;
186 };
187 
188 static int phy_setup_op(struct zynq_gem_priv *priv, u32 phy_addr, u32 regnum,
189 			u32 op, u16 *data)
190 {
191 	u32 mgtcr;
192 	struct zynq_gem_regs *regs = priv->iobase;
193 	int err;
194 
195 	err = wait_for_bit_le32(&regs->nwsr, ZYNQ_GEM_NWSR_MDIOIDLE_MASK,
196 				true, 20000, false);
197 	if (err)
198 		return err;
199 
200 	/* Construct mgtcr mask for the operation */
201 	mgtcr = ZYNQ_GEM_PHYMNTNC_OP_MASK | op |
202 		(phy_addr << ZYNQ_GEM_PHYMNTNC_PHYAD_SHIFT_MASK) |
203 		(regnum << ZYNQ_GEM_PHYMNTNC_PHREG_SHIFT_MASK) | *data;
204 
205 	/* Write mgtcr and wait for completion */
206 	writel(mgtcr, &regs->phymntnc);
207 
208 	err = wait_for_bit_le32(&regs->nwsr, ZYNQ_GEM_NWSR_MDIOIDLE_MASK,
209 				true, 20000, false);
210 	if (err)
211 		return err;
212 
213 	if (op == ZYNQ_GEM_PHYMNTNC_OP_R_MASK)
214 		*data = readl(&regs->phymntnc);
215 
216 	return 0;
217 }
218 
219 static int phyread(struct zynq_gem_priv *priv, u32 phy_addr,
220 		   u32 regnum, u16 *val)
221 {
222 	int ret;
223 
224 	ret = phy_setup_op(priv, phy_addr, regnum,
225 			   ZYNQ_GEM_PHYMNTNC_OP_R_MASK, val);
226 
227 	if (!ret)
228 		debug("%s: phy_addr %d, regnum 0x%x, val 0x%x\n", __func__,
229 		      phy_addr, regnum, *val);
230 
231 	return ret;
232 }
233 
234 static int phywrite(struct zynq_gem_priv *priv, u32 phy_addr,
235 		    u32 regnum, u16 data)
236 {
237 	debug("%s: phy_addr %d, regnum 0x%x, data 0x%x\n", __func__, phy_addr,
238 	      regnum, data);
239 
240 	return phy_setup_op(priv, phy_addr, regnum,
241 			    ZYNQ_GEM_PHYMNTNC_OP_W_MASK, &data);
242 }
243 
244 static int phy_detection(struct udevice *dev)
245 {
246 	int i;
247 	u16 phyreg = 0;
248 	struct zynq_gem_priv *priv = dev->priv;
249 
250 	if (priv->phyaddr != -1) {
251 		phyread(priv, priv->phyaddr, PHY_DETECT_REG, &phyreg);
252 		if ((phyreg != 0xFFFF) &&
253 		    ((phyreg & PHY_DETECT_MASK) == PHY_DETECT_MASK)) {
254 			/* Found a valid PHY address */
255 			debug("Default phy address %d is valid\n",
256 			      priv->phyaddr);
257 			return 0;
258 		} else {
259 			debug("PHY address is not setup correctly %d\n",
260 			      priv->phyaddr);
261 			priv->phyaddr = -1;
262 		}
263 	}
264 
265 	debug("detecting phy address\n");
266 	if (priv->phyaddr == -1) {
267 		/* detect the PHY address */
268 		for (i = 31; i >= 0; i--) {
269 			phyread(priv, i, PHY_DETECT_REG, &phyreg);
270 			if ((phyreg != 0xFFFF) &&
271 			    ((phyreg & PHY_DETECT_MASK) == PHY_DETECT_MASK)) {
272 				/* Found a valid PHY address */
273 				priv->phyaddr = i;
274 				debug("Found valid phy address, %d\n", i);
275 				return 0;
276 			}
277 		}
278 	}
279 	printf("PHY is not detected\n");
280 	return -1;
281 }
282 
283 static int zynq_gem_setup_mac(struct udevice *dev)
284 {
285 	u32 i, macaddrlow, macaddrhigh;
286 	struct eth_pdata *pdata = dev_get_platdata(dev);
287 	struct zynq_gem_priv *priv = dev_get_priv(dev);
288 	struct zynq_gem_regs *regs = priv->iobase;
289 
290 	/* Set the MAC bits [31:0] in BOT */
291 	macaddrlow = pdata->enetaddr[0];
292 	macaddrlow |= pdata->enetaddr[1] << 8;
293 	macaddrlow |= pdata->enetaddr[2] << 16;
294 	macaddrlow |= pdata->enetaddr[3] << 24;
295 
296 	/* Set MAC bits [47:32] in TOP */
297 	macaddrhigh = pdata->enetaddr[4];
298 	macaddrhigh |= pdata->enetaddr[5] << 8;
299 
300 	for (i = 0; i < 4; i++) {
301 		writel(0, &regs->laddr[i][LADDR_LOW]);
302 		writel(0, &regs->laddr[i][LADDR_HIGH]);
303 		/* Do not use MATCHx register */
304 		writel(0, &regs->match[i]);
305 	}
306 
307 	writel(macaddrlow, &regs->laddr[0][LADDR_LOW]);
308 	writel(macaddrhigh, &regs->laddr[0][LADDR_HIGH]);
309 
310 	return 0;
311 }
312 
313 static int zynq_phy_init(struct udevice *dev)
314 {
315 	int ret;
316 	struct zynq_gem_priv *priv = dev_get_priv(dev);
317 	struct zynq_gem_regs *regs = priv->iobase;
318 	const u32 supported = SUPPORTED_10baseT_Half |
319 			SUPPORTED_10baseT_Full |
320 			SUPPORTED_100baseT_Half |
321 			SUPPORTED_100baseT_Full |
322 			SUPPORTED_1000baseT_Half |
323 			SUPPORTED_1000baseT_Full;
324 
325 	/* Enable only MDIO bus */
326 	writel(ZYNQ_GEM_NWCTRL_MDEN_MASK, &regs->nwctrl);
327 
328 	if ((priv->interface != PHY_INTERFACE_MODE_SGMII) &&
329 	    (priv->interface != PHY_INTERFACE_MODE_GMII)) {
330 		ret = phy_detection(dev);
331 		if (ret) {
332 			printf("GEM PHY init failed\n");
333 			return ret;
334 		}
335 	}
336 
337 	priv->phydev = phy_connect(priv->bus, priv->phyaddr, dev,
338 				   priv->interface);
339 	if (!priv->phydev)
340 		return -ENODEV;
341 
342 	priv->phydev->supported &= supported | ADVERTISED_Pause |
343 				  ADVERTISED_Asym_Pause;
344 	if (priv->max_speed) {
345 		ret = phy_set_supported(priv->phydev, priv->max_speed);
346 		if (ret)
347 			return ret;
348 	}
349 
350 	priv->phydev->advertising = priv->phydev->supported;
351 	priv->phydev->node = priv->phy_of_node;
352 
353 	return phy_config(priv->phydev);
354 }
355 
356 static int zynq_gem_init(struct udevice *dev)
357 {
358 	u32 i, nwconfig;
359 	int ret;
360 	unsigned long clk_rate = 0;
361 	struct zynq_gem_priv *priv = dev_get_priv(dev);
362 	struct zynq_gem_regs *regs = priv->iobase;
363 	struct emac_bd *dummy_tx_bd = &priv->tx_bd[TX_FREE_DESC];
364 	struct emac_bd *dummy_rx_bd = &priv->tx_bd[TX_FREE_DESC + 2];
365 
366 	if (!priv->init) {
367 		/* Disable all interrupts */
368 		writel(0xFFFFFFFF, &regs->idr);
369 
370 		/* Disable the receiver & transmitter */
371 		writel(0, &regs->nwctrl);
372 		writel(0, &regs->txsr);
373 		writel(0, &regs->rxsr);
374 		writel(0, &regs->phymntnc);
375 
376 		/* Clear the Hash registers for the mac address
377 		 * pointed by AddressPtr
378 		 */
379 		writel(0x0, &regs->hashl);
380 		/* Write bits [63:32] in TOP */
381 		writel(0x0, &regs->hashh);
382 
383 		/* Clear all counters */
384 		for (i = 0; i < STAT_SIZE; i++)
385 			readl(&regs->stat[i]);
386 
387 		/* Setup RxBD space */
388 		memset(priv->rx_bd, 0, RX_BUF * sizeof(struct emac_bd));
389 
390 		for (i = 0; i < RX_BUF; i++) {
391 			priv->rx_bd[i].status = 0xF0000000;
392 			priv->rx_bd[i].addr =
393 					((ulong)(priv->rxbuffers) +
394 							(i * PKTSIZE_ALIGN));
395 		}
396 		/* WRAP bit to last BD */
397 		priv->rx_bd[--i].addr |= ZYNQ_GEM_RXBUF_WRAP_MASK;
398 		/* Write RxBDs to IP */
399 		writel((ulong)priv->rx_bd, &regs->rxqbase);
400 
401 		/* Setup for DMA Configuration register */
402 		writel(ZYNQ_GEM_DMACR_INIT, &regs->dmacr);
403 
404 		/* Setup for Network Control register, MDIO, Rx and Tx enable */
405 		setbits_le32(&regs->nwctrl, ZYNQ_GEM_NWCTRL_MDEN_MASK);
406 
407 		/* Disable the second priority queue */
408 		dummy_tx_bd->addr = 0;
409 		dummy_tx_bd->status = ZYNQ_GEM_TXBUF_WRAP_MASK |
410 				ZYNQ_GEM_TXBUF_LAST_MASK|
411 				ZYNQ_GEM_TXBUF_USED_MASK;
412 
413 		dummy_rx_bd->addr = ZYNQ_GEM_RXBUF_WRAP_MASK |
414 				ZYNQ_GEM_RXBUF_NEW_MASK;
415 		dummy_rx_bd->status = 0;
416 
417 		writel((ulong)dummy_tx_bd, &regs->transmit_q1_ptr);
418 		writel((ulong)dummy_rx_bd, &regs->receive_q1_ptr);
419 
420 		priv->init++;
421 	}
422 
423 	ret = phy_startup(priv->phydev);
424 	if (ret)
425 		return ret;
426 
427 	if (!priv->phydev->link) {
428 		printf("%s: No link.\n", priv->phydev->dev->name);
429 		return -1;
430 	}
431 
432 	nwconfig = ZYNQ_GEM_NWCFG_INIT;
433 
434 	/*
435 	 * Set SGMII enable PCS selection only if internal PCS/PMA
436 	 * core is used and interface is SGMII.
437 	 */
438 	if (priv->interface == PHY_INTERFACE_MODE_SGMII &&
439 	    priv->int_pcs) {
440 		nwconfig |= ZYNQ_GEM_NWCFG_SGMII_ENBL |
441 			    ZYNQ_GEM_NWCFG_PCS_SEL;
442 #ifdef CONFIG_ARM64
443 		writel(readl(&regs->pcscntrl) | ZYNQ_GEM_PCS_CTL_ANEG_ENBL,
444 		       &regs->pcscntrl);
445 #endif
446 	}
447 
448 	switch (priv->phydev->speed) {
449 	case SPEED_1000:
450 		writel(nwconfig | ZYNQ_GEM_NWCFG_SPEED1000,
451 		       &regs->nwcfg);
452 		clk_rate = ZYNQ_GEM_FREQUENCY_1000;
453 		break;
454 	case SPEED_100:
455 		writel(nwconfig | ZYNQ_GEM_NWCFG_SPEED100,
456 		       &regs->nwcfg);
457 		clk_rate = ZYNQ_GEM_FREQUENCY_100;
458 		break;
459 	case SPEED_10:
460 		clk_rate = ZYNQ_GEM_FREQUENCY_10;
461 		break;
462 	}
463 
464 	ret = clk_set_rate(&priv->clk, clk_rate);
465 	if (IS_ERR_VALUE(ret) && ret != (unsigned long)-ENOSYS) {
466 		dev_err(dev, "failed to set tx clock rate\n");
467 		return ret;
468 	}
469 
470 	ret = clk_enable(&priv->clk);
471 	if (ret && ret != -ENOSYS) {
472 		dev_err(dev, "failed to enable tx clock\n");
473 		return ret;
474 	}
475 
476 	setbits_le32(&regs->nwctrl, ZYNQ_GEM_NWCTRL_RXEN_MASK |
477 					ZYNQ_GEM_NWCTRL_TXEN_MASK);
478 
479 	return 0;
480 }
481 
482 static int zynq_gem_send(struct udevice *dev, void *ptr, int len)
483 {
484 	u32 addr, size;
485 	struct zynq_gem_priv *priv = dev_get_priv(dev);
486 	struct zynq_gem_regs *regs = priv->iobase;
487 	struct emac_bd *current_bd = &priv->tx_bd[1];
488 
489 	/* Setup Tx BD */
490 	memset(priv->tx_bd, 0, sizeof(struct emac_bd));
491 
492 	priv->tx_bd->addr = (ulong)ptr;
493 	priv->tx_bd->status = (len & ZYNQ_GEM_TXBUF_FRMLEN_MASK) |
494 			       ZYNQ_GEM_TXBUF_LAST_MASK;
495 	/* Dummy descriptor to mark it as the last in descriptor chain */
496 	current_bd->addr = 0x0;
497 	current_bd->status = ZYNQ_GEM_TXBUF_WRAP_MASK |
498 			     ZYNQ_GEM_TXBUF_LAST_MASK|
499 			     ZYNQ_GEM_TXBUF_USED_MASK;
500 
501 	/* setup BD */
502 	writel((ulong)priv->tx_bd, &regs->txqbase);
503 
504 	addr = (ulong) ptr;
505 	addr &= ~(ARCH_DMA_MINALIGN - 1);
506 	size = roundup(len, ARCH_DMA_MINALIGN);
507 	flush_dcache_range(addr, addr + size);
508 
509 	addr = (ulong)priv->rxbuffers;
510 	addr &= ~(ARCH_DMA_MINALIGN - 1);
511 	size = roundup((RX_BUF * PKTSIZE_ALIGN), ARCH_DMA_MINALIGN);
512 	flush_dcache_range(addr, addr + size);
513 	barrier();
514 
515 	/* Start transmit */
516 	setbits_le32(&regs->nwctrl, ZYNQ_GEM_NWCTRL_STARTTX_MASK);
517 
518 	/* Read TX BD status */
519 	if (priv->tx_bd->status & ZYNQ_GEM_TXBUF_EXHAUSTED)
520 		printf("TX buffers exhausted in mid frame\n");
521 
522 	return wait_for_bit_le32(&regs->txsr, ZYNQ_GEM_TSR_DONE,
523 				 true, 20000, true);
524 }
525 
526 /* Do not check frame_recd flag in rx_status register 0x20 - just poll BD */
527 static int zynq_gem_recv(struct udevice *dev, int flags, uchar **packetp)
528 {
529 	int frame_len;
530 	u32 addr;
531 	struct zynq_gem_priv *priv = dev_get_priv(dev);
532 	struct emac_bd *current_bd = &priv->rx_bd[priv->rxbd_current];
533 
534 	if (!(current_bd->addr & ZYNQ_GEM_RXBUF_NEW_MASK))
535 		return -1;
536 
537 	if (!(current_bd->status &
538 			(ZYNQ_GEM_RXBUF_SOF_MASK | ZYNQ_GEM_RXBUF_EOF_MASK))) {
539 		printf("GEM: SOF or EOF not set for last buffer received!\n");
540 		return -1;
541 	}
542 
543 	frame_len = current_bd->status & ZYNQ_GEM_RXBUF_LEN_MASK;
544 	if (!frame_len) {
545 		printf("%s: Zero size packet?\n", __func__);
546 		return -1;
547 	}
548 
549 	addr = current_bd->addr & ZYNQ_GEM_RXBUF_ADD_MASK;
550 	addr &= ~(ARCH_DMA_MINALIGN - 1);
551 	*packetp = (uchar *)(uintptr_t)addr;
552 
553 	return frame_len;
554 }
555 
556 static int zynq_gem_free_pkt(struct udevice *dev, uchar *packet, int length)
557 {
558 	struct zynq_gem_priv *priv = dev_get_priv(dev);
559 	struct emac_bd *current_bd = &priv->rx_bd[priv->rxbd_current];
560 	struct emac_bd *first_bd;
561 
562 	if (current_bd->status & ZYNQ_GEM_RXBUF_SOF_MASK) {
563 		priv->rx_first_buf = priv->rxbd_current;
564 	} else {
565 		current_bd->addr &= ~ZYNQ_GEM_RXBUF_NEW_MASK;
566 		current_bd->status = 0xF0000000; /* FIXME */
567 	}
568 
569 	if (current_bd->status & ZYNQ_GEM_RXBUF_EOF_MASK) {
570 		first_bd = &priv->rx_bd[priv->rx_first_buf];
571 		first_bd->addr &= ~ZYNQ_GEM_RXBUF_NEW_MASK;
572 		first_bd->status = 0xF0000000;
573 	}
574 
575 	if ((++priv->rxbd_current) >= RX_BUF)
576 		priv->rxbd_current = 0;
577 
578 	return 0;
579 }
580 
581 static void zynq_gem_halt(struct udevice *dev)
582 {
583 	struct zynq_gem_priv *priv = dev_get_priv(dev);
584 	struct zynq_gem_regs *regs = priv->iobase;
585 
586 	clrsetbits_le32(&regs->nwctrl, ZYNQ_GEM_NWCTRL_RXEN_MASK |
587 						ZYNQ_GEM_NWCTRL_TXEN_MASK, 0);
588 }
589 
590 __weak int zynq_board_read_rom_ethaddr(unsigned char *ethaddr)
591 {
592 	return -ENOSYS;
593 }
594 
595 static int zynq_gem_read_rom_mac(struct udevice *dev)
596 {
597 	struct eth_pdata *pdata = dev_get_platdata(dev);
598 
599 	if (!pdata)
600 		return -ENOSYS;
601 
602 	return zynq_board_read_rom_ethaddr(pdata->enetaddr);
603 }
604 
605 static int zynq_gem_miiphy_read(struct mii_dev *bus, int addr,
606 				int devad, int reg)
607 {
608 	struct zynq_gem_priv *priv = bus->priv;
609 	int ret;
610 	u16 val = 0;
611 
612 	ret = phyread(priv, addr, reg, &val);
613 	debug("%s 0x%x, 0x%x, 0x%x, 0x%x\n", __func__, addr, reg, val, ret);
614 	return val;
615 }
616 
617 static int zynq_gem_miiphy_write(struct mii_dev *bus, int addr, int devad,
618 				 int reg, u16 value)
619 {
620 	struct zynq_gem_priv *priv = bus->priv;
621 
622 	debug("%s 0x%x, 0x%x, 0x%x\n", __func__, addr, reg, value);
623 	return phywrite(priv, addr, reg, value);
624 }
625 
626 static int zynq_gem_probe(struct udevice *dev)
627 {
628 	void *bd_space;
629 	struct zynq_gem_priv *priv = dev_get_priv(dev);
630 	int ret;
631 
632 	/* Align rxbuffers to ARCH_DMA_MINALIGN */
633 	priv->rxbuffers = memalign(ARCH_DMA_MINALIGN, RX_BUF * PKTSIZE_ALIGN);
634 	if (!priv->rxbuffers)
635 		return -ENOMEM;
636 
637 	memset(priv->rxbuffers, 0, RX_BUF * PKTSIZE_ALIGN);
638 
639 	/* Align bd_space to MMU_SECTION_SHIFT */
640 	bd_space = memalign(1 << MMU_SECTION_SHIFT, BD_SPACE);
641 	if (!bd_space)
642 		return -ENOMEM;
643 
644 	mmu_set_region_dcache_behaviour((phys_addr_t)bd_space,
645 					BD_SPACE, DCACHE_OFF);
646 
647 	/* Initialize the bd spaces for tx and rx bd's */
648 	priv->tx_bd = (struct emac_bd *)bd_space;
649 	priv->rx_bd = (struct emac_bd *)((ulong)bd_space + BD_SEPRN_SPACE);
650 
651 	ret = clk_get_by_name(dev, "tx_clk", &priv->clk);
652 	if (ret < 0) {
653 		dev_err(dev, "failed to get clock\n");
654 		return -EINVAL;
655 	}
656 
657 	priv->bus = mdio_alloc();
658 	priv->bus->read = zynq_gem_miiphy_read;
659 	priv->bus->write = zynq_gem_miiphy_write;
660 	priv->bus->priv = priv;
661 
662 	ret = mdio_register_seq(priv->bus, dev->seq);
663 	if (ret)
664 		return ret;
665 
666 	return zynq_phy_init(dev);
667 }
668 
669 static int zynq_gem_remove(struct udevice *dev)
670 {
671 	struct zynq_gem_priv *priv = dev_get_priv(dev);
672 
673 	free(priv->phydev);
674 	mdio_unregister(priv->bus);
675 	mdio_free(priv->bus);
676 
677 	return 0;
678 }
679 
680 static const struct eth_ops zynq_gem_ops = {
681 	.start			= zynq_gem_init,
682 	.send			= zynq_gem_send,
683 	.recv			= zynq_gem_recv,
684 	.free_pkt		= zynq_gem_free_pkt,
685 	.stop			= zynq_gem_halt,
686 	.write_hwaddr		= zynq_gem_setup_mac,
687 	.read_rom_hwaddr	= zynq_gem_read_rom_mac,
688 };
689 
690 static int zynq_gem_ofdata_to_platdata(struct udevice *dev)
691 {
692 	struct eth_pdata *pdata = dev_get_platdata(dev);
693 	struct zynq_gem_priv *priv = dev_get_priv(dev);
694 	struct ofnode_phandle_args phandle_args;
695 	const char *phy_mode;
696 
697 	pdata->iobase = (phys_addr_t)dev_read_addr(dev);
698 	priv->iobase = (struct zynq_gem_regs *)pdata->iobase;
699 	/* Hardcode for now */
700 	priv->phyaddr = -1;
701 
702 	if (!dev_read_phandle_with_args(dev, "phy-handle", NULL, 0, 0,
703 					&phandle_args)) {
704 		debug("phy-handle does exist %s\n", dev->name);
705 		priv->phyaddr = ofnode_read_u32_default(phandle_args.node,
706 							"reg", -1);
707 		priv->phy_of_node = phandle_args.node;
708 		priv->max_speed = ofnode_read_u32_default(phandle_args.node,
709 							  "max-speed",
710 							  SPEED_1000);
711 	}
712 
713 	phy_mode = dev_read_prop(dev, "phy-mode", NULL);
714 	if (phy_mode)
715 		pdata->phy_interface = phy_get_interface_by_name(phy_mode);
716 	if (pdata->phy_interface == -1) {
717 		debug("%s: Invalid PHY interface '%s'\n", __func__, phy_mode);
718 		return -EINVAL;
719 	}
720 	priv->interface = pdata->phy_interface;
721 
722 	priv->int_pcs = dev_read_bool(dev, "is-internal-pcspma");
723 
724 	printf("ZYNQ GEM: %lx, phyaddr %x, interface %s\n", (ulong)priv->iobase,
725 	       priv->phyaddr, phy_string_for_interface(priv->interface));
726 
727 	return 0;
728 }
729 
730 static const struct udevice_id zynq_gem_ids[] = {
731 	{ .compatible = "cdns,zynqmp-gem" },
732 	{ .compatible = "cdns,zynq-gem" },
733 	{ .compatible = "cdns,gem" },
734 	{ }
735 };
736 
737 U_BOOT_DRIVER(zynq_gem) = {
738 	.name	= "zynq_gem",
739 	.id	= UCLASS_ETH,
740 	.of_match = zynq_gem_ids,
741 	.ofdata_to_platdata = zynq_gem_ofdata_to_platdata,
742 	.probe	= zynq_gem_probe,
743 	.remove	= zynq_gem_remove,
744 	.ops	= &zynq_gem_ops,
745 	.priv_auto_alloc_size = sizeof(struct zynq_gem_priv),
746 	.platdata_auto_alloc_size = sizeof(struct eth_pdata),
747 };
748