xref: /openbmc/u-boot/drivers/net/zynq_gem.c (revision 4101f687)
1 /*
2  * (C) Copyright 2011 Michal Simek
3  *
4  * Michal SIMEK <monstr@monstr.eu>
5  *
6  * Based on Xilinx gmac driver:
7  * (C) Copyright 2011 Xilinx
8  *
9  * SPDX-License-Identifier:	GPL-2.0+
10  */
11 
12 #include <common.h>
13 #include <dm.h>
14 #include <net.h>
15 #include <netdev.h>
16 #include <config.h>
17 #include <console.h>
18 #include <malloc.h>
19 #include <asm/io.h>
20 #include <phy.h>
21 #include <miiphy.h>
22 #include <wait_bit.h>
23 #include <watchdog.h>
24 #include <asm/system.h>
25 #include <asm/arch/hardware.h>
26 #include <asm/arch/sys_proto.h>
27 #include <asm-generic/errno.h>
28 
29 DECLARE_GLOBAL_DATA_PTR;
30 
31 /* Bit/mask specification */
32 #define ZYNQ_GEM_PHYMNTNC_OP_MASK	0x40020000 /* operation mask bits */
33 #define ZYNQ_GEM_PHYMNTNC_OP_R_MASK	0x20000000 /* read operation */
34 #define ZYNQ_GEM_PHYMNTNC_OP_W_MASK	0x10000000 /* write operation */
35 #define ZYNQ_GEM_PHYMNTNC_PHYAD_SHIFT_MASK	23 /* Shift bits for PHYAD */
36 #define ZYNQ_GEM_PHYMNTNC_PHREG_SHIFT_MASK	18 /* Shift bits for PHREG */
37 
38 #define ZYNQ_GEM_RXBUF_EOF_MASK		0x00008000 /* End of frame. */
39 #define ZYNQ_GEM_RXBUF_SOF_MASK		0x00004000 /* Start of frame. */
40 #define ZYNQ_GEM_RXBUF_LEN_MASK		0x00003FFF /* Mask for length field */
41 
42 #define ZYNQ_GEM_RXBUF_WRAP_MASK	0x00000002 /* Wrap bit, last BD */
43 #define ZYNQ_GEM_RXBUF_NEW_MASK		0x00000001 /* Used bit.. */
44 #define ZYNQ_GEM_RXBUF_ADD_MASK		0xFFFFFFFC /* Mask for address */
45 
46 /* Wrap bit, last descriptor */
47 #define ZYNQ_GEM_TXBUF_WRAP_MASK	0x40000000
48 #define ZYNQ_GEM_TXBUF_LAST_MASK	0x00008000 /* Last buffer */
49 #define ZYNQ_GEM_TXBUF_USED_MASK	0x80000000 /* Used by Hw */
50 
51 #define ZYNQ_GEM_NWCTRL_TXEN_MASK	0x00000008 /* Enable transmit */
52 #define ZYNQ_GEM_NWCTRL_RXEN_MASK	0x00000004 /* Enable receive */
53 #define ZYNQ_GEM_NWCTRL_MDEN_MASK	0x00000010 /* Enable MDIO port */
54 #define ZYNQ_GEM_NWCTRL_STARTTX_MASK	0x00000200 /* Start tx (tx_go) */
55 
56 #define ZYNQ_GEM_NWCFG_SPEED100		0x000000001 /* 100 Mbps operation */
57 #define ZYNQ_GEM_NWCFG_SPEED1000	0x000000400 /* 1Gbps operation */
58 #define ZYNQ_GEM_NWCFG_FDEN		0x000000002 /* Full Duplex mode */
59 #define ZYNQ_GEM_NWCFG_FSREM		0x000020000 /* FCS removal */
60 #ifdef CONFIG_ARM64
61 #define ZYNQ_GEM_NWCFG_MDCCLKDIV	0x000100000 /* Div pclk by 64, max 160MHz */
62 #else
63 #define ZYNQ_GEM_NWCFG_MDCCLKDIV	0x0000c0000 /* Div pclk by 48, max 120MHz */
64 #endif
65 
66 #ifdef CONFIG_ARM64
67 # define ZYNQ_GEM_DBUS_WIDTH	(1 << 21) /* 64 bit bus */
68 #else
69 # define ZYNQ_GEM_DBUS_WIDTH	(0 << 21) /* 32 bit bus */
70 #endif
71 
72 #define ZYNQ_GEM_NWCFG_INIT		(ZYNQ_GEM_DBUS_WIDTH | \
73 					ZYNQ_GEM_NWCFG_FDEN | \
74 					ZYNQ_GEM_NWCFG_FSREM | \
75 					ZYNQ_GEM_NWCFG_MDCCLKDIV)
76 
77 #define ZYNQ_GEM_NWSR_MDIOIDLE_MASK	0x00000004 /* PHY management idle */
78 
79 #define ZYNQ_GEM_DMACR_BLENGTH		0x00000004 /* INCR4 AHB bursts */
80 /* Use full configured addressable space (8 Kb) */
81 #define ZYNQ_GEM_DMACR_RXSIZE		0x00000300
82 /* Use full configured addressable space (4 Kb) */
83 #define ZYNQ_GEM_DMACR_TXSIZE		0x00000400
84 /* Set with binary 00011000 to use 1536 byte(1*max length frame/buffer) */
85 #define ZYNQ_GEM_DMACR_RXBUF		0x00180000
86 
87 #define ZYNQ_GEM_DMACR_INIT		(ZYNQ_GEM_DMACR_BLENGTH | \
88 					ZYNQ_GEM_DMACR_RXSIZE | \
89 					ZYNQ_GEM_DMACR_TXSIZE | \
90 					ZYNQ_GEM_DMACR_RXBUF)
91 
92 #define ZYNQ_GEM_TSR_DONE		0x00000020 /* Tx done mask */
93 
94 /* Use MII register 1 (MII status register) to detect PHY */
95 #define PHY_DETECT_REG  1
96 
97 /* Mask used to verify certain PHY features (or register contents)
98  * in the register above:
99  *  0x1000: 10Mbps full duplex support
100  *  0x0800: 10Mbps half duplex support
101  *  0x0008: Auto-negotiation support
102  */
103 #define PHY_DETECT_MASK 0x1808
104 
105 /* TX BD status masks */
106 #define ZYNQ_GEM_TXBUF_FRMLEN_MASK	0x000007ff
107 #define ZYNQ_GEM_TXBUF_EXHAUSTED	0x08000000
108 #define ZYNQ_GEM_TXBUF_UNDERRUN		0x10000000
109 
110 /* Clock frequencies for different speeds */
111 #define ZYNQ_GEM_FREQUENCY_10	2500000UL
112 #define ZYNQ_GEM_FREQUENCY_100	25000000UL
113 #define ZYNQ_GEM_FREQUENCY_1000	125000000UL
114 
115 /* Device registers */
116 struct zynq_gem_regs {
117 	u32 nwctrl; /* 0x0 - Network Control reg */
118 	u32 nwcfg; /* 0x4 - Network Config reg */
119 	u32 nwsr; /* 0x8 - Network Status reg */
120 	u32 reserved1;
121 	u32 dmacr; /* 0x10 - DMA Control reg */
122 	u32 txsr; /* 0x14 - TX Status reg */
123 	u32 rxqbase; /* 0x18 - RX Q Base address reg */
124 	u32 txqbase; /* 0x1c - TX Q Base address reg */
125 	u32 rxsr; /* 0x20 - RX Status reg */
126 	u32 reserved2[2];
127 	u32 idr; /* 0x2c - Interrupt Disable reg */
128 	u32 reserved3;
129 	u32 phymntnc; /* 0x34 - Phy Maintaince reg */
130 	u32 reserved4[18];
131 	u32 hashl; /* 0x80 - Hash Low address reg */
132 	u32 hashh; /* 0x84 - Hash High address reg */
133 #define LADDR_LOW	0
134 #define LADDR_HIGH	1
135 	u32 laddr[4][LADDR_HIGH + 1]; /* 0x8c - Specific1 addr low/high reg */
136 	u32 match[4]; /* 0xa8 - Type ID1 Match reg */
137 	u32 reserved6[18];
138 #define STAT_SIZE	44
139 	u32 stat[STAT_SIZE]; /* 0x100 - Octects transmitted Low reg */
140 	u32 reserved7[164];
141 	u32 transmit_q1_ptr; /* 0x440 - Transmit priority queue 1 */
142 	u32 reserved8[15];
143 	u32 receive_q1_ptr; /* 0x480 - Receive priority queue 1 */
144 };
145 
146 /* BD descriptors */
147 struct emac_bd {
148 	u32 addr; /* Next descriptor pointer */
149 	u32 status;
150 };
151 
152 #define RX_BUF 32
153 /* Page table entries are set to 1MB, or multiples of 1MB
154  * (not < 1MB). driver uses less bd's so use 1MB bdspace.
155  */
156 #define BD_SPACE	0x100000
157 /* BD separation space */
158 #define BD_SEPRN_SPACE	(RX_BUF * sizeof(struct emac_bd))
159 
160 /* Setup the first free TX descriptor */
161 #define TX_FREE_DESC	2
162 
163 /* Initialized, rxbd_current, rx_first_buf must be 0 after init */
164 struct zynq_gem_priv {
165 	struct emac_bd *tx_bd;
166 	struct emac_bd *rx_bd;
167 	char *rxbuffers;
168 	u32 rxbd_current;
169 	u32 rx_first_buf;
170 	int phyaddr;
171 	u32 emio;
172 	int init;
173 	struct zynq_gem_regs *iobase;
174 	phy_interface_t interface;
175 	struct phy_device *phydev;
176 	struct mii_dev *bus;
177 };
178 
179 static inline int mdio_wait(struct zynq_gem_regs *regs)
180 {
181 	u32 timeout = 20000;
182 
183 	/* Wait till MDIO interface is ready to accept a new transaction. */
184 	while (--timeout) {
185 		if (readl(&regs->nwsr) & ZYNQ_GEM_NWSR_MDIOIDLE_MASK)
186 			break;
187 		WATCHDOG_RESET();
188 	}
189 
190 	if (!timeout) {
191 		printf("%s: Timeout\n", __func__);
192 		return 1;
193 	}
194 
195 	return 0;
196 }
197 
198 static u32 phy_setup_op(struct zynq_gem_priv *priv, u32 phy_addr, u32 regnum,
199 			u32 op, u16 *data)
200 {
201 	u32 mgtcr;
202 	struct zynq_gem_regs *regs = priv->iobase;
203 
204 	if (mdio_wait(regs))
205 		return 1;
206 
207 	/* Construct mgtcr mask for the operation */
208 	mgtcr = ZYNQ_GEM_PHYMNTNC_OP_MASK | op |
209 		(phy_addr << ZYNQ_GEM_PHYMNTNC_PHYAD_SHIFT_MASK) |
210 		(regnum << ZYNQ_GEM_PHYMNTNC_PHREG_SHIFT_MASK) | *data;
211 
212 	/* Write mgtcr and wait for completion */
213 	writel(mgtcr, &regs->phymntnc);
214 
215 	if (mdio_wait(regs))
216 		return 1;
217 
218 	if (op == ZYNQ_GEM_PHYMNTNC_OP_R_MASK)
219 		*data = readl(&regs->phymntnc);
220 
221 	return 0;
222 }
223 
224 static u32 phyread(struct zynq_gem_priv *priv, u32 phy_addr,
225 		   u32 regnum, u16 *val)
226 {
227 	u32 ret;
228 
229 	ret = phy_setup_op(priv, phy_addr, regnum,
230 			   ZYNQ_GEM_PHYMNTNC_OP_R_MASK, val);
231 
232 	if (!ret)
233 		debug("%s: phy_addr %d, regnum 0x%x, val 0x%x\n", __func__,
234 		      phy_addr, regnum, *val);
235 
236 	return ret;
237 }
238 
239 static u32 phywrite(struct zynq_gem_priv *priv, u32 phy_addr,
240 		    u32 regnum, u16 data)
241 {
242 	debug("%s: phy_addr %d, regnum 0x%x, data 0x%x\n", __func__, phy_addr,
243 	      regnum, data);
244 
245 	return phy_setup_op(priv, phy_addr, regnum,
246 			    ZYNQ_GEM_PHYMNTNC_OP_W_MASK, &data);
247 }
248 
249 static int phy_detection(struct udevice *dev)
250 {
251 	int i;
252 	u16 phyreg;
253 	struct zynq_gem_priv *priv = dev->priv;
254 
255 	if (priv->phyaddr != -1) {
256 		phyread(priv, priv->phyaddr, PHY_DETECT_REG, &phyreg);
257 		if ((phyreg != 0xFFFF) &&
258 		    ((phyreg & PHY_DETECT_MASK) == PHY_DETECT_MASK)) {
259 			/* Found a valid PHY address */
260 			debug("Default phy address %d is valid\n",
261 			      priv->phyaddr);
262 			return 0;
263 		} else {
264 			debug("PHY address is not setup correctly %d\n",
265 			      priv->phyaddr);
266 			priv->phyaddr = -1;
267 		}
268 	}
269 
270 	debug("detecting phy address\n");
271 	if (priv->phyaddr == -1) {
272 		/* detect the PHY address */
273 		for (i = 31; i >= 0; i--) {
274 			phyread(priv, i, PHY_DETECT_REG, &phyreg);
275 			if ((phyreg != 0xFFFF) &&
276 			    ((phyreg & PHY_DETECT_MASK) == PHY_DETECT_MASK)) {
277 				/* Found a valid PHY address */
278 				priv->phyaddr = i;
279 				debug("Found valid phy address, %d\n", i);
280 				return 0;
281 			}
282 		}
283 	}
284 	printf("PHY is not detected\n");
285 	return -1;
286 }
287 
288 static int zynq_gem_setup_mac(struct udevice *dev)
289 {
290 	u32 i, macaddrlow, macaddrhigh;
291 	struct eth_pdata *pdata = dev_get_platdata(dev);
292 	struct zynq_gem_priv *priv = dev_get_priv(dev);
293 	struct zynq_gem_regs *regs = priv->iobase;
294 
295 	/* Set the MAC bits [31:0] in BOT */
296 	macaddrlow = pdata->enetaddr[0];
297 	macaddrlow |= pdata->enetaddr[1] << 8;
298 	macaddrlow |= pdata->enetaddr[2] << 16;
299 	macaddrlow |= pdata->enetaddr[3] << 24;
300 
301 	/* Set MAC bits [47:32] in TOP */
302 	macaddrhigh = pdata->enetaddr[4];
303 	macaddrhigh |= pdata->enetaddr[5] << 8;
304 
305 	for (i = 0; i < 4; i++) {
306 		writel(0, &regs->laddr[i][LADDR_LOW]);
307 		writel(0, &regs->laddr[i][LADDR_HIGH]);
308 		/* Do not use MATCHx register */
309 		writel(0, &regs->match[i]);
310 	}
311 
312 	writel(macaddrlow, &regs->laddr[0][LADDR_LOW]);
313 	writel(macaddrhigh, &regs->laddr[0][LADDR_HIGH]);
314 
315 	return 0;
316 }
317 
318 static int zynq_phy_init(struct udevice *dev)
319 {
320 	int ret;
321 	struct zynq_gem_priv *priv = dev_get_priv(dev);
322 	struct zynq_gem_regs *regs = priv->iobase;
323 	const u32 supported = SUPPORTED_10baseT_Half |
324 			SUPPORTED_10baseT_Full |
325 			SUPPORTED_100baseT_Half |
326 			SUPPORTED_100baseT_Full |
327 			SUPPORTED_1000baseT_Half |
328 			SUPPORTED_1000baseT_Full;
329 
330 	/* Enable only MDIO bus */
331 	writel(ZYNQ_GEM_NWCTRL_MDEN_MASK, &regs->nwctrl);
332 
333 	ret = phy_detection(dev);
334 	if (ret) {
335 		printf("GEM PHY init failed\n");
336 		return ret;
337 	}
338 
339 	priv->phydev = phy_connect(priv->bus, priv->phyaddr, dev,
340 				   priv->interface);
341 	if (!priv->phydev)
342 		return -ENODEV;
343 
344 	priv->phydev->supported = supported | ADVERTISED_Pause |
345 				  ADVERTISED_Asym_Pause;
346 	priv->phydev->advertising = priv->phydev->supported;
347 	phy_config(priv->phydev);
348 
349 	return 0;
350 }
351 
352 static int zynq_gem_init(struct udevice *dev)
353 {
354 	u32 i;
355 	unsigned long clk_rate = 0;
356 	struct zynq_gem_priv *priv = dev_get_priv(dev);
357 	struct zynq_gem_regs *regs = priv->iobase;
358 	struct emac_bd *dummy_tx_bd = &priv->tx_bd[TX_FREE_DESC];
359 	struct emac_bd *dummy_rx_bd = &priv->tx_bd[TX_FREE_DESC + 2];
360 
361 	if (!priv->init) {
362 		/* Disable all interrupts */
363 		writel(0xFFFFFFFF, &regs->idr);
364 
365 		/* Disable the receiver & transmitter */
366 		writel(0, &regs->nwctrl);
367 		writel(0, &regs->txsr);
368 		writel(0, &regs->rxsr);
369 		writel(0, &regs->phymntnc);
370 
371 		/* Clear the Hash registers for the mac address
372 		 * pointed by AddressPtr
373 		 */
374 		writel(0x0, &regs->hashl);
375 		/* Write bits [63:32] in TOP */
376 		writel(0x0, &regs->hashh);
377 
378 		/* Clear all counters */
379 		for (i = 0; i < STAT_SIZE; i++)
380 			readl(&regs->stat[i]);
381 
382 		/* Setup RxBD space */
383 		memset(priv->rx_bd, 0, RX_BUF * sizeof(struct emac_bd));
384 
385 		for (i = 0; i < RX_BUF; i++) {
386 			priv->rx_bd[i].status = 0xF0000000;
387 			priv->rx_bd[i].addr =
388 					((ulong)(priv->rxbuffers) +
389 							(i * PKTSIZE_ALIGN));
390 		}
391 		/* WRAP bit to last BD */
392 		priv->rx_bd[--i].addr |= ZYNQ_GEM_RXBUF_WRAP_MASK;
393 		/* Write RxBDs to IP */
394 		writel((ulong)priv->rx_bd, &regs->rxqbase);
395 
396 		/* Setup for DMA Configuration register */
397 		writel(ZYNQ_GEM_DMACR_INIT, &regs->dmacr);
398 
399 		/* Setup for Network Control register, MDIO, Rx and Tx enable */
400 		setbits_le32(&regs->nwctrl, ZYNQ_GEM_NWCTRL_MDEN_MASK);
401 
402 		/* Disable the second priority queue */
403 		dummy_tx_bd->addr = 0;
404 		dummy_tx_bd->status = ZYNQ_GEM_TXBUF_WRAP_MASK |
405 				ZYNQ_GEM_TXBUF_LAST_MASK|
406 				ZYNQ_GEM_TXBUF_USED_MASK;
407 
408 		dummy_rx_bd->addr = ZYNQ_GEM_RXBUF_WRAP_MASK |
409 				ZYNQ_GEM_RXBUF_NEW_MASK;
410 		dummy_rx_bd->status = 0;
411 		flush_dcache_range((ulong)&dummy_tx_bd, (ulong)&dummy_tx_bd +
412 				   sizeof(dummy_tx_bd));
413 		flush_dcache_range((ulong)&dummy_rx_bd, (ulong)&dummy_rx_bd +
414 				   sizeof(dummy_rx_bd));
415 
416 		writel((ulong)dummy_tx_bd, &regs->transmit_q1_ptr);
417 		writel((ulong)dummy_rx_bd, &regs->receive_q1_ptr);
418 
419 		priv->init++;
420 	}
421 
422 	phy_startup(priv->phydev);
423 
424 	if (!priv->phydev->link) {
425 		printf("%s: No link.\n", priv->phydev->dev->name);
426 		return -1;
427 	}
428 
429 	switch (priv->phydev->speed) {
430 	case SPEED_1000:
431 		writel(ZYNQ_GEM_NWCFG_INIT | ZYNQ_GEM_NWCFG_SPEED1000,
432 		       &regs->nwcfg);
433 		clk_rate = ZYNQ_GEM_FREQUENCY_1000;
434 		break;
435 	case SPEED_100:
436 		writel(ZYNQ_GEM_NWCFG_INIT | ZYNQ_GEM_NWCFG_SPEED100,
437 		       &regs->nwcfg);
438 		clk_rate = ZYNQ_GEM_FREQUENCY_100;
439 		break;
440 	case SPEED_10:
441 		clk_rate = ZYNQ_GEM_FREQUENCY_10;
442 		break;
443 	}
444 
445 	/* Change the rclk and clk only not using EMIO interface */
446 	if (!priv->emio)
447 		zynq_slcr_gem_clk_setup((ulong)priv->iobase !=
448 					ZYNQ_GEM_BASEADDR0, clk_rate);
449 
450 	setbits_le32(&regs->nwctrl, ZYNQ_GEM_NWCTRL_RXEN_MASK |
451 					ZYNQ_GEM_NWCTRL_TXEN_MASK);
452 
453 	return 0;
454 }
455 
456 static int zynq_gem_send(struct udevice *dev, void *ptr, int len)
457 {
458 	u32 addr, size;
459 	struct zynq_gem_priv *priv = dev_get_priv(dev);
460 	struct zynq_gem_regs *regs = priv->iobase;
461 	struct emac_bd *current_bd = &priv->tx_bd[1];
462 
463 	/* Setup Tx BD */
464 	memset(priv->tx_bd, 0, sizeof(struct emac_bd));
465 
466 	priv->tx_bd->addr = (ulong)ptr;
467 	priv->tx_bd->status = (len & ZYNQ_GEM_TXBUF_FRMLEN_MASK) |
468 			       ZYNQ_GEM_TXBUF_LAST_MASK;
469 	/* Dummy descriptor to mark it as the last in descriptor chain */
470 	current_bd->addr = 0x0;
471 	current_bd->status = ZYNQ_GEM_TXBUF_WRAP_MASK |
472 			     ZYNQ_GEM_TXBUF_LAST_MASK|
473 			     ZYNQ_GEM_TXBUF_USED_MASK;
474 
475 	/* setup BD */
476 	writel((ulong)priv->tx_bd, &regs->txqbase);
477 
478 	addr = (ulong) ptr;
479 	addr &= ~(ARCH_DMA_MINALIGN - 1);
480 	size = roundup(len, ARCH_DMA_MINALIGN);
481 	flush_dcache_range(addr, addr + size);
482 
483 	addr = (ulong)priv->rxbuffers;
484 	addr &= ~(ARCH_DMA_MINALIGN - 1);
485 	size = roundup((RX_BUF * PKTSIZE_ALIGN), ARCH_DMA_MINALIGN);
486 	flush_dcache_range(addr, addr + size);
487 	barrier();
488 
489 	/* Start transmit */
490 	setbits_le32(&regs->nwctrl, ZYNQ_GEM_NWCTRL_STARTTX_MASK);
491 
492 	/* Read TX BD status */
493 	if (priv->tx_bd->status & ZYNQ_GEM_TXBUF_EXHAUSTED)
494 		printf("TX buffers exhausted in mid frame\n");
495 
496 	return wait_for_bit(__func__, &regs->txsr, ZYNQ_GEM_TSR_DONE,
497 			    true, 20000, true);
498 }
499 
500 /* Do not check frame_recd flag in rx_status register 0x20 - just poll BD */
501 static int zynq_gem_recv(struct udevice *dev, int flags, uchar **packetp)
502 {
503 	int frame_len;
504 	u32 addr;
505 	struct zynq_gem_priv *priv = dev_get_priv(dev);
506 	struct emac_bd *current_bd = &priv->rx_bd[priv->rxbd_current];
507 
508 	if (!(current_bd->addr & ZYNQ_GEM_RXBUF_NEW_MASK))
509 		return -1;
510 
511 	if (!(current_bd->status &
512 			(ZYNQ_GEM_RXBUF_SOF_MASK | ZYNQ_GEM_RXBUF_EOF_MASK))) {
513 		printf("GEM: SOF or EOF not set for last buffer received!\n");
514 		return -1;
515 	}
516 
517 	frame_len = current_bd->status & ZYNQ_GEM_RXBUF_LEN_MASK;
518 	if (!frame_len) {
519 		printf("%s: Zero size packet?\n", __func__);
520 		return -1;
521 	}
522 
523 	addr = current_bd->addr & ZYNQ_GEM_RXBUF_ADD_MASK;
524 	addr &= ~(ARCH_DMA_MINALIGN - 1);
525 	*packetp = (uchar *)(uintptr_t)addr;
526 
527 	return frame_len;
528 }
529 
530 static int zynq_gem_free_pkt(struct udevice *dev, uchar *packet, int length)
531 {
532 	struct zynq_gem_priv *priv = dev_get_priv(dev);
533 	struct emac_bd *current_bd = &priv->rx_bd[priv->rxbd_current];
534 	struct emac_bd *first_bd;
535 
536 	if (current_bd->status & ZYNQ_GEM_RXBUF_SOF_MASK) {
537 		priv->rx_first_buf = priv->rxbd_current;
538 	} else {
539 		current_bd->addr &= ~ZYNQ_GEM_RXBUF_NEW_MASK;
540 		current_bd->status = 0xF0000000; /* FIXME */
541 	}
542 
543 	if (current_bd->status & ZYNQ_GEM_RXBUF_EOF_MASK) {
544 		first_bd = &priv->rx_bd[priv->rx_first_buf];
545 		first_bd->addr &= ~ZYNQ_GEM_RXBUF_NEW_MASK;
546 		first_bd->status = 0xF0000000;
547 	}
548 
549 	if ((++priv->rxbd_current) >= RX_BUF)
550 		priv->rxbd_current = 0;
551 
552 	return 0;
553 }
554 
555 static void zynq_gem_halt(struct udevice *dev)
556 {
557 	struct zynq_gem_priv *priv = dev_get_priv(dev);
558 	struct zynq_gem_regs *regs = priv->iobase;
559 
560 	clrsetbits_le32(&regs->nwctrl, ZYNQ_GEM_NWCTRL_RXEN_MASK |
561 						ZYNQ_GEM_NWCTRL_TXEN_MASK, 0);
562 }
563 
564 static int zynq_gem_miiphy_read(struct mii_dev *bus, int addr,
565 				int devad, int reg)
566 {
567 	struct zynq_gem_priv *priv = bus->priv;
568 	int ret;
569 	u16 val;
570 
571 	ret = phyread(priv, addr, reg, &val);
572 	debug("%s 0x%x, 0x%x, 0x%x, 0x%x\n", __func__, addr, reg, val, ret);
573 	return val;
574 }
575 
576 static int zynq_gem_miiphy_write(struct mii_dev *bus, int addr, int devad,
577 				 int reg, u16 value)
578 {
579 	struct zynq_gem_priv *priv = bus->priv;
580 
581 	debug("%s 0x%x, 0x%x, 0x%x\n", __func__, addr, reg, value);
582 	return phywrite(priv, addr, reg, value);
583 }
584 
585 static int zynq_gem_probe(struct udevice *dev)
586 {
587 	void *bd_space;
588 	struct zynq_gem_priv *priv = dev_get_priv(dev);
589 	int ret;
590 
591 	/* Align rxbuffers to ARCH_DMA_MINALIGN */
592 	priv->rxbuffers = memalign(ARCH_DMA_MINALIGN, RX_BUF * PKTSIZE_ALIGN);
593 	memset(priv->rxbuffers, 0, RX_BUF * PKTSIZE_ALIGN);
594 
595 	/* Align bd_space to MMU_SECTION_SHIFT */
596 	bd_space = memalign(1 << MMU_SECTION_SHIFT, BD_SPACE);
597 	mmu_set_region_dcache_behaviour((phys_addr_t)bd_space,
598 					BD_SPACE, DCACHE_OFF);
599 
600 	/* Initialize the bd spaces for tx and rx bd's */
601 	priv->tx_bd = (struct emac_bd *)bd_space;
602 	priv->rx_bd = (struct emac_bd *)((ulong)bd_space + BD_SEPRN_SPACE);
603 
604 	priv->bus = mdio_alloc();
605 	priv->bus->read = zynq_gem_miiphy_read;
606 	priv->bus->write = zynq_gem_miiphy_write;
607 	priv->bus->priv = priv;
608 	strcpy(priv->bus->name, "gem");
609 
610 	ret = mdio_register(priv->bus);
611 	if (ret)
612 		return ret;
613 
614 	zynq_phy_init(dev);
615 
616 	return 0;
617 }
618 
619 static int zynq_gem_remove(struct udevice *dev)
620 {
621 	struct zynq_gem_priv *priv = dev_get_priv(dev);
622 
623 	free(priv->phydev);
624 	mdio_unregister(priv->bus);
625 	mdio_free(priv->bus);
626 
627 	return 0;
628 }
629 
630 static const struct eth_ops zynq_gem_ops = {
631 	.start			= zynq_gem_init,
632 	.send			= zynq_gem_send,
633 	.recv			= zynq_gem_recv,
634 	.free_pkt		= zynq_gem_free_pkt,
635 	.stop			= zynq_gem_halt,
636 	.write_hwaddr		= zynq_gem_setup_mac,
637 };
638 
639 static int zynq_gem_ofdata_to_platdata(struct udevice *dev)
640 {
641 	struct eth_pdata *pdata = dev_get_platdata(dev);
642 	struct zynq_gem_priv *priv = dev_get_priv(dev);
643 	int offset = 0;
644 	const char *phy_mode;
645 
646 	pdata->iobase = (phys_addr_t)dev_get_addr(dev);
647 	priv->iobase = (struct zynq_gem_regs *)pdata->iobase;
648 	/* Hardcode for now */
649 	priv->emio = 0;
650 	priv->phyaddr = -1;
651 
652 	offset = fdtdec_lookup_phandle(gd->fdt_blob, dev->of_offset,
653 				       "phy-handle");
654 	if (offset > 0)
655 		priv->phyaddr = fdtdec_get_int(gd->fdt_blob, offset, "reg", -1);
656 
657 	phy_mode = fdt_getprop(gd->fdt_blob, dev->of_offset, "phy-mode", NULL);
658 	if (phy_mode)
659 		pdata->phy_interface = phy_get_interface_by_name(phy_mode);
660 	if (pdata->phy_interface == -1) {
661 		debug("%s: Invalid PHY interface '%s'\n", __func__, phy_mode);
662 		return -EINVAL;
663 	}
664 	priv->interface = pdata->phy_interface;
665 
666 	printf("ZYNQ GEM: %lx, phyaddr %d, interface %s\n", (ulong)priv->iobase,
667 	       priv->phyaddr, phy_string_for_interface(priv->interface));
668 
669 	return 0;
670 }
671 
672 static const struct udevice_id zynq_gem_ids[] = {
673 	{ .compatible = "cdns,zynqmp-gem" },
674 	{ .compatible = "cdns,zynq-gem" },
675 	{ .compatible = "cdns,gem" },
676 	{ }
677 };
678 
679 U_BOOT_DRIVER(zynq_gem) = {
680 	.name	= "zynq_gem",
681 	.id	= UCLASS_ETH,
682 	.of_match = zynq_gem_ids,
683 	.ofdata_to_platdata = zynq_gem_ofdata_to_platdata,
684 	.probe	= zynq_gem_probe,
685 	.remove	= zynq_gem_remove,
686 	.ops	= &zynq_gem_ops,
687 	.priv_auto_alloc_size = sizeof(struct zynq_gem_priv),
688 	.platdata_auto_alloc_size = sizeof(struct eth_pdata),
689 };
690