1 /* 2 * Copyright (C) 2011 Michal Simek <monstr@monstr.eu> 3 * Copyright (C) 2011 PetaLogix 4 * Copyright (C) 2010 Xilinx, Inc. All rights reserved. 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #include <config.h> 10 #include <common.h> 11 #include <net.h> 12 #include <malloc.h> 13 #include <asm/io.h> 14 #include <phy.h> 15 #include <miiphy.h> 16 17 #if !defined(CONFIG_PHYLIB) 18 # error AXI_ETHERNET requires PHYLIB 19 #endif 20 21 /* Link setup */ 22 #define XAE_EMMC_LINKSPEED_MASK 0xC0000000 /* Link speed */ 23 #define XAE_EMMC_LINKSPD_10 0x00000000 /* Link Speed mask for 10 Mbit */ 24 #define XAE_EMMC_LINKSPD_100 0x40000000 /* Link Speed mask for 100 Mbit */ 25 #define XAE_EMMC_LINKSPD_1000 0x80000000 /* Link Speed mask for 1000 Mbit */ 26 27 /* Interrupt Status/Enable/Mask Registers bit definitions */ 28 #define XAE_INT_RXRJECT_MASK 0x00000008 /* Rx frame rejected */ 29 #define XAE_INT_MGTRDY_MASK 0x00000080 /* MGT clock Lock */ 30 31 /* Receive Configuration Word 1 (RCW1) Register bit definitions */ 32 #define XAE_RCW1_RX_MASK 0x10000000 /* Receiver enable */ 33 34 /* Transmitter Configuration (TC) Register bit definitions */ 35 #define XAE_TC_TX_MASK 0x10000000 /* Transmitter enable */ 36 37 #define XAE_UAW1_UNICASTADDR_MASK 0x0000FFFF 38 39 /* MDIO Management Configuration (MC) Register bit definitions */ 40 #define XAE_MDIO_MC_MDIOEN_MASK 0x00000040 /* MII management enable*/ 41 42 /* MDIO Management Control Register (MCR) Register bit definitions */ 43 #define XAE_MDIO_MCR_PHYAD_MASK 0x1F000000 /* Phy Address Mask */ 44 #define XAE_MDIO_MCR_PHYAD_SHIFT 24 /* Phy Address Shift */ 45 #define XAE_MDIO_MCR_REGAD_MASK 0x001F0000 /* Reg Address Mask */ 46 #define XAE_MDIO_MCR_REGAD_SHIFT 16 /* Reg Address Shift */ 47 #define XAE_MDIO_MCR_OP_READ_MASK 0x00008000 /* Op Code Read Mask */ 48 #define XAE_MDIO_MCR_OP_WRITE_MASK 0x00004000 /* Op Code Write Mask */ 49 #define XAE_MDIO_MCR_INITIATE_MASK 0x00000800 /* Ready Mask */ 50 #define XAE_MDIO_MCR_READY_MASK 0x00000080 /* Ready Mask */ 51 52 #define XAE_MDIO_DIV_DFT 29 /* Default MDIO clock divisor */ 53 54 /* DMA macros */ 55 /* Bitmasks of XAXIDMA_CR_OFFSET register */ 56 #define XAXIDMA_CR_RUNSTOP_MASK 0x00000001 /* Start/stop DMA channel */ 57 #define XAXIDMA_CR_RESET_MASK 0x00000004 /* Reset DMA engine */ 58 59 /* Bitmasks of XAXIDMA_SR_OFFSET register */ 60 #define XAXIDMA_HALTED_MASK 0x00000001 /* DMA channel halted */ 61 62 /* Bitmask for interrupts */ 63 #define XAXIDMA_IRQ_IOC_MASK 0x00001000 /* Completion intr */ 64 #define XAXIDMA_IRQ_DELAY_MASK 0x00002000 /* Delay interrupt */ 65 #define XAXIDMA_IRQ_ALL_MASK 0x00007000 /* All interrupts */ 66 67 /* Bitmasks of XAXIDMA_BD_CTRL_OFFSET register */ 68 #define XAXIDMA_BD_CTRL_TXSOF_MASK 0x08000000 /* First tx packet */ 69 #define XAXIDMA_BD_CTRL_TXEOF_MASK 0x04000000 /* Last tx packet */ 70 71 #define DMAALIGN 128 72 73 static u8 rxframe[PKTSIZE_ALIGN] __attribute((aligned(DMAALIGN))); 74 75 /* Reflect dma offsets */ 76 struct axidma_reg { 77 u32 control; /* DMACR */ 78 u32 status; /* DMASR */ 79 u32 current; /* CURDESC */ 80 u32 reserved; 81 u32 tail; /* TAILDESC */ 82 }; 83 84 /* Private driver structures */ 85 struct axidma_priv { 86 struct axidma_reg *dmatx; 87 struct axidma_reg *dmarx; 88 int phyaddr; 89 90 struct phy_device *phydev; 91 struct mii_dev *bus; 92 }; 93 94 /* BD descriptors */ 95 struct axidma_bd { 96 u32 next; /* Next descriptor pointer */ 97 u32 reserved1; 98 u32 phys; /* Buffer address */ 99 u32 reserved2; 100 u32 reserved3; 101 u32 reserved4; 102 u32 cntrl; /* Control */ 103 u32 status; /* Status */ 104 u32 app0; 105 u32 app1; /* TX start << 16 | insert */ 106 u32 app2; /* TX csum seed */ 107 u32 app3; 108 u32 app4; 109 u32 sw_id_offset; 110 u32 reserved5; 111 u32 reserved6; 112 }; 113 114 /* Static BDs - driver uses only one BD */ 115 static struct axidma_bd tx_bd __attribute((aligned(DMAALIGN))); 116 static struct axidma_bd rx_bd __attribute((aligned(DMAALIGN))); 117 118 struct axi_regs { 119 u32 reserved[3]; 120 u32 is; /* 0xC: Interrupt status */ 121 u32 reserved2; 122 u32 ie; /* 0x14: Interrupt enable */ 123 u32 reserved3[251]; 124 u32 rcw1; /* 0x404: Rx Configuration Word 1 */ 125 u32 tc; /* 0x408: Tx Configuration */ 126 u32 reserved4; 127 u32 emmc; /* 0x410: EMAC mode configuration */ 128 u32 reserved5[59]; 129 u32 mdio_mc; /* 0x500: MII Management Config */ 130 u32 mdio_mcr; /* 0x504: MII Management Control */ 131 u32 mdio_mwd; /* 0x508: MII Management Write Data */ 132 u32 mdio_mrd; /* 0x50C: MII Management Read Data */ 133 u32 reserved6[124]; 134 u32 uaw0; /* 0x700: Unicast address word 0 */ 135 u32 uaw1; /* 0x704: Unicast address word 1 */ 136 }; 137 138 /* Use MII register 1 (MII status register) to detect PHY */ 139 #define PHY_DETECT_REG 1 140 141 /* 142 * Mask used to verify certain PHY features (or register contents) 143 * in the register above: 144 * 0x1000: 10Mbps full duplex support 145 * 0x0800: 10Mbps half duplex support 146 * 0x0008: Auto-negotiation support 147 */ 148 #define PHY_DETECT_MASK 0x1808 149 150 static inline int mdio_wait(struct eth_device *dev) 151 { 152 struct axi_regs *regs = (struct axi_regs *)dev->iobase; 153 u32 timeout = 200; 154 155 /* Wait till MDIO interface is ready to accept a new transaction. */ 156 while (timeout && (!(in_be32(®s->mdio_mcr) 157 & XAE_MDIO_MCR_READY_MASK))) { 158 timeout--; 159 udelay(1); 160 } 161 if (!timeout) { 162 printf("%s: Timeout\n", __func__); 163 return 1; 164 } 165 return 0; 166 } 167 168 static u32 phyread(struct eth_device *dev, u32 phyaddress, u32 registernum, 169 u16 *val) 170 { 171 struct axi_regs *regs = (struct axi_regs *)dev->iobase; 172 u32 mdioctrlreg = 0; 173 174 if (mdio_wait(dev)) 175 return 1; 176 177 mdioctrlreg = ((phyaddress << XAE_MDIO_MCR_PHYAD_SHIFT) & 178 XAE_MDIO_MCR_PHYAD_MASK) | 179 ((registernum << XAE_MDIO_MCR_REGAD_SHIFT) 180 & XAE_MDIO_MCR_REGAD_MASK) | 181 XAE_MDIO_MCR_INITIATE_MASK | 182 XAE_MDIO_MCR_OP_READ_MASK; 183 184 out_be32(®s->mdio_mcr, mdioctrlreg); 185 186 if (mdio_wait(dev)) 187 return 1; 188 189 /* Read data */ 190 *val = in_be32(®s->mdio_mrd); 191 return 0; 192 } 193 194 static u32 phywrite(struct eth_device *dev, u32 phyaddress, u32 registernum, 195 u32 data) 196 { 197 struct axi_regs *regs = (struct axi_regs *)dev->iobase; 198 u32 mdioctrlreg = 0; 199 200 if (mdio_wait(dev)) 201 return 1; 202 203 mdioctrlreg = ((phyaddress << XAE_MDIO_MCR_PHYAD_SHIFT) & 204 XAE_MDIO_MCR_PHYAD_MASK) | 205 ((registernum << XAE_MDIO_MCR_REGAD_SHIFT) 206 & XAE_MDIO_MCR_REGAD_MASK) | 207 XAE_MDIO_MCR_INITIATE_MASK | 208 XAE_MDIO_MCR_OP_WRITE_MASK; 209 210 /* Write data */ 211 out_be32(®s->mdio_mwd, data); 212 213 out_be32(®s->mdio_mcr, mdioctrlreg); 214 215 if (mdio_wait(dev)) 216 return 1; 217 218 return 0; 219 } 220 221 /* Setting axi emac and phy to proper setting */ 222 static int setup_phy(struct eth_device *dev) 223 { 224 u16 phyreg; 225 u32 i, speed, emmc_reg, ret; 226 struct axidma_priv *priv = dev->priv; 227 struct axi_regs *regs = (struct axi_regs *)dev->iobase; 228 struct phy_device *phydev; 229 230 u32 supported = SUPPORTED_10baseT_Half | 231 SUPPORTED_10baseT_Full | 232 SUPPORTED_100baseT_Half | 233 SUPPORTED_100baseT_Full | 234 SUPPORTED_1000baseT_Half | 235 SUPPORTED_1000baseT_Full; 236 237 if (priv->phyaddr == -1) { 238 /* Detect the PHY address */ 239 for (i = 31; i >= 0; i--) { 240 ret = phyread(dev, i, PHY_DETECT_REG, &phyreg); 241 if (!ret && (phyreg != 0xFFFF) && 242 ((phyreg & PHY_DETECT_MASK) == PHY_DETECT_MASK)) { 243 /* Found a valid PHY address */ 244 priv->phyaddr = i; 245 debug("axiemac: Found valid phy address, %x\n", 246 phyreg); 247 break; 248 } 249 } 250 } 251 252 /* Interface - look at tsec */ 253 phydev = phy_connect(priv->bus, priv->phyaddr, dev, 0); 254 255 phydev->supported &= supported; 256 phydev->advertising = phydev->supported; 257 priv->phydev = phydev; 258 phy_config(phydev); 259 if (phy_startup(phydev)) { 260 printf("axiemac: could not initialize PHY %s\n", 261 phydev->dev->name); 262 return 0; 263 } 264 if (!phydev->link) { 265 printf("%s: No link.\n", phydev->dev->name); 266 return 0; 267 } 268 269 switch (phydev->speed) { 270 case 1000: 271 speed = XAE_EMMC_LINKSPD_1000; 272 break; 273 case 100: 274 speed = XAE_EMMC_LINKSPD_100; 275 break; 276 case 10: 277 speed = XAE_EMMC_LINKSPD_10; 278 break; 279 default: 280 return 0; 281 } 282 283 /* Setup the emac for the phy speed */ 284 emmc_reg = in_be32(®s->emmc); 285 emmc_reg &= ~XAE_EMMC_LINKSPEED_MASK; 286 emmc_reg |= speed; 287 288 /* Write new speed setting out to Axi Ethernet */ 289 out_be32(®s->emmc, emmc_reg); 290 291 /* 292 * Setting the operating speed of the MAC needs a delay. There 293 * doesn't seem to be register to poll, so please consider this 294 * during your application design. 295 */ 296 udelay(1); 297 298 return 1; 299 } 300 301 /* STOP DMA transfers */ 302 static void axiemac_halt(struct eth_device *dev) 303 { 304 struct axidma_priv *priv = dev->priv; 305 u32 temp; 306 307 /* Stop the hardware */ 308 temp = in_be32(&priv->dmatx->control); 309 temp &= ~XAXIDMA_CR_RUNSTOP_MASK; 310 out_be32(&priv->dmatx->control, temp); 311 312 temp = in_be32(&priv->dmarx->control); 313 temp &= ~XAXIDMA_CR_RUNSTOP_MASK; 314 out_be32(&priv->dmarx->control, temp); 315 316 debug("axiemac: Halted\n"); 317 } 318 319 static int axi_ethernet_init(struct eth_device *dev) 320 { 321 struct axi_regs *regs = (struct axi_regs *)dev->iobase; 322 u32 timeout = 200; 323 324 /* 325 * Check the status of the MgtRdy bit in the interrupt status 326 * registers. This must be done to allow the MGT clock to become stable 327 * for the Sgmii and 1000BaseX PHY interfaces. No other register reads 328 * will be valid until this bit is valid. 329 * The bit is always a 1 for all other PHY interfaces. 330 */ 331 while (timeout && (!(in_be32(®s->is) & XAE_INT_MGTRDY_MASK))) { 332 timeout--; 333 udelay(1); 334 } 335 if (!timeout) { 336 printf("%s: Timeout\n", __func__); 337 return 1; 338 } 339 340 /* Stop the device and reset HW */ 341 /* Disable interrupts */ 342 out_be32(®s->ie, 0); 343 344 /* Disable the receiver */ 345 out_be32(®s->rcw1, in_be32(®s->rcw1) & ~XAE_RCW1_RX_MASK); 346 347 /* 348 * Stopping the receiver in mid-packet causes a dropped packet 349 * indication from HW. Clear it. 350 */ 351 /* Set the interrupt status register to clear the interrupt */ 352 out_be32(®s->is, XAE_INT_RXRJECT_MASK); 353 354 /* Setup HW */ 355 /* Set default MDIO divisor */ 356 out_be32(®s->mdio_mc, XAE_MDIO_DIV_DFT | XAE_MDIO_MC_MDIOEN_MASK); 357 358 debug("axiemac: InitHw done\n"); 359 return 0; 360 } 361 362 static int axiemac_setup_mac(struct eth_device *dev) 363 { 364 struct axi_regs *regs = (struct axi_regs *)dev->iobase; 365 366 /* Set the MAC address */ 367 int val = ((dev->enetaddr[3] << 24) | (dev->enetaddr[2] << 16) | 368 (dev->enetaddr[1] << 8) | (dev->enetaddr[0])); 369 out_be32(®s->uaw0, val); 370 371 val = (dev->enetaddr[5] << 8) | dev->enetaddr[4] ; 372 val |= in_be32(®s->uaw1) & ~XAE_UAW1_UNICASTADDR_MASK; 373 out_be32(®s->uaw1, val); 374 return 0; 375 } 376 377 /* Reset DMA engine */ 378 static void axi_dma_init(struct eth_device *dev) 379 { 380 struct axidma_priv *priv = dev->priv; 381 u32 timeout = 500; 382 383 /* Reset the engine so the hardware starts from a known state */ 384 out_be32(&priv->dmatx->control, XAXIDMA_CR_RESET_MASK); 385 out_be32(&priv->dmarx->control, XAXIDMA_CR_RESET_MASK); 386 387 /* At the initialization time, hardware should finish reset quickly */ 388 while (timeout--) { 389 /* Check transmit/receive channel */ 390 /* Reset is done when the reset bit is low */ 391 if (!(in_be32(&priv->dmatx->control) | 392 in_be32(&priv->dmarx->control)) 393 & XAXIDMA_CR_RESET_MASK) { 394 break; 395 } 396 } 397 if (!timeout) 398 printf("%s: Timeout\n", __func__); 399 } 400 401 static int axiemac_init(struct eth_device *dev, bd_t * bis) 402 { 403 struct axidma_priv *priv = dev->priv; 404 struct axi_regs *regs = (struct axi_regs *)dev->iobase; 405 u32 temp; 406 407 debug("axiemac: Init started\n"); 408 /* 409 * Initialize AXIDMA engine. AXIDMA engine must be initialized before 410 * AxiEthernet. During AXIDMA engine initialization, AXIDMA hardware is 411 * reset, and since AXIDMA reset line is connected to AxiEthernet, this 412 * would ensure a reset of AxiEthernet. 413 */ 414 axi_dma_init(dev); 415 416 /* Initialize AxiEthernet hardware. */ 417 if (axi_ethernet_init(dev)) 418 return -1; 419 420 /* Disable all RX interrupts before RxBD space setup */ 421 temp = in_be32(&priv->dmarx->control); 422 temp &= ~XAXIDMA_IRQ_ALL_MASK; 423 out_be32(&priv->dmarx->control, temp); 424 425 /* Start DMA RX channel. Now it's ready to receive data.*/ 426 out_be32(&priv->dmarx->current, (u32)&rx_bd); 427 428 /* Setup the BD. */ 429 memset(&rx_bd, 0, sizeof(rx_bd)); 430 rx_bd.next = (u32)&rx_bd; 431 rx_bd.phys = (u32)&rxframe; 432 rx_bd.cntrl = sizeof(rxframe); 433 /* Flush the last BD so DMA core could see the updates */ 434 flush_cache((u32)&rx_bd, sizeof(rx_bd)); 435 436 /* It is necessary to flush rxframe because if you don't do it 437 * then cache can contain uninitialized data */ 438 flush_cache((u32)&rxframe, sizeof(rxframe)); 439 440 /* Start the hardware */ 441 temp = in_be32(&priv->dmarx->control); 442 temp |= XAXIDMA_CR_RUNSTOP_MASK; 443 out_be32(&priv->dmarx->control, temp); 444 445 /* Rx BD is ready - start */ 446 out_be32(&priv->dmarx->tail, (u32)&rx_bd); 447 448 /* Enable TX */ 449 out_be32(®s->tc, XAE_TC_TX_MASK); 450 /* Enable RX */ 451 out_be32(®s->rcw1, XAE_RCW1_RX_MASK); 452 453 /* PHY setup */ 454 if (!setup_phy(dev)) { 455 axiemac_halt(dev); 456 return -1; 457 } 458 459 debug("axiemac: Init complete\n"); 460 return 0; 461 } 462 463 static int axiemac_send(struct eth_device *dev, void *ptr, int len) 464 { 465 struct axidma_priv *priv = dev->priv; 466 u32 timeout; 467 468 if (len > PKTSIZE_ALIGN) 469 len = PKTSIZE_ALIGN; 470 471 /* Flush packet to main memory to be trasfered by DMA */ 472 flush_cache((u32)ptr, len); 473 474 /* Setup Tx BD */ 475 memset(&tx_bd, 0, sizeof(tx_bd)); 476 /* At the end of the ring, link the last BD back to the top */ 477 tx_bd.next = (u32)&tx_bd; 478 tx_bd.phys = (u32)ptr; 479 /* Save len */ 480 tx_bd.cntrl = len | XAXIDMA_BD_CTRL_TXSOF_MASK | 481 XAXIDMA_BD_CTRL_TXEOF_MASK; 482 483 /* Flush the last BD so DMA core could see the updates */ 484 flush_cache((u32)&tx_bd, sizeof(tx_bd)); 485 486 if (in_be32(&priv->dmatx->status) & XAXIDMA_HALTED_MASK) { 487 u32 temp; 488 out_be32(&priv->dmatx->current, (u32)&tx_bd); 489 /* Start the hardware */ 490 temp = in_be32(&priv->dmatx->control); 491 temp |= XAXIDMA_CR_RUNSTOP_MASK; 492 out_be32(&priv->dmatx->control, temp); 493 } 494 495 /* Start transfer */ 496 out_be32(&priv->dmatx->tail, (u32)&tx_bd); 497 498 /* Wait for transmission to complete */ 499 debug("axiemac: Waiting for tx to be done\n"); 500 timeout = 200; 501 while (timeout && (!in_be32(&priv->dmatx->status) & 502 (XAXIDMA_IRQ_DELAY_MASK | XAXIDMA_IRQ_IOC_MASK))) { 503 timeout--; 504 udelay(1); 505 } 506 if (!timeout) { 507 printf("%s: Timeout\n", __func__); 508 return 1; 509 } 510 511 debug("axiemac: Sending complete\n"); 512 return 0; 513 } 514 515 static int isrxready(struct eth_device *dev) 516 { 517 u32 status; 518 struct axidma_priv *priv = dev->priv; 519 520 /* Read pending interrupts */ 521 status = in_be32(&priv->dmarx->status); 522 523 /* Acknowledge pending interrupts */ 524 out_be32(&priv->dmarx->status, status & XAXIDMA_IRQ_ALL_MASK); 525 526 /* 527 * If Reception done interrupt is asserted, call RX call back function 528 * to handle the processed BDs and then raise the according flag. 529 */ 530 if ((status & (XAXIDMA_IRQ_DELAY_MASK | XAXIDMA_IRQ_IOC_MASK))) 531 return 1; 532 533 return 0; 534 } 535 536 static int axiemac_recv(struct eth_device *dev) 537 { 538 u32 length; 539 struct axidma_priv *priv = dev->priv; 540 u32 temp; 541 542 /* Wait for an incoming packet */ 543 if (!isrxready(dev)) 544 return 0; 545 546 debug("axiemac: RX data ready\n"); 547 548 /* Disable IRQ for a moment till packet is handled */ 549 temp = in_be32(&priv->dmarx->control); 550 temp &= ~XAXIDMA_IRQ_ALL_MASK; 551 out_be32(&priv->dmarx->control, temp); 552 553 length = rx_bd.app4 & 0xFFFF; /* max length mask */ 554 #ifdef DEBUG 555 print_buffer(&rxframe, &rxframe[0], 1, length, 16); 556 #endif 557 /* Pass the received frame up for processing */ 558 if (length) 559 NetReceive(rxframe, length); 560 561 #ifdef DEBUG 562 /* It is useful to clear buffer to be sure that it is consistent */ 563 memset(rxframe, 0, sizeof(rxframe)); 564 #endif 565 /* Setup RxBD */ 566 /* Clear the whole buffer and setup it again - all flags are cleared */ 567 memset(&rx_bd, 0, sizeof(rx_bd)); 568 rx_bd.next = (u32)&rx_bd; 569 rx_bd.phys = (u32)&rxframe; 570 rx_bd.cntrl = sizeof(rxframe); 571 572 /* Write bd to HW */ 573 flush_cache((u32)&rx_bd, sizeof(rx_bd)); 574 575 /* It is necessary to flush rxframe because if you don't do it 576 * then cache will contain previous packet */ 577 flush_cache((u32)&rxframe, sizeof(rxframe)); 578 579 /* Rx BD is ready - start again */ 580 out_be32(&priv->dmarx->tail, (u32)&rx_bd); 581 582 debug("axiemac: RX completed, framelength = %d\n", length); 583 584 return length; 585 } 586 587 static int axiemac_miiphy_read(const char *devname, uchar addr, 588 uchar reg, ushort *val) 589 { 590 struct eth_device *dev = eth_get_dev(); 591 u32 ret; 592 593 ret = phyread(dev, addr, reg, val); 594 debug("axiemac: Read MII 0x%x, 0x%x, 0x%x\n", addr, reg, *val); 595 return ret; 596 } 597 598 static int axiemac_miiphy_write(const char *devname, uchar addr, 599 uchar reg, ushort val) 600 { 601 struct eth_device *dev = eth_get_dev(); 602 603 debug("axiemac: Write MII 0x%x, 0x%x, 0x%x\n", addr, reg, val); 604 return phywrite(dev, addr, reg, val); 605 } 606 607 static int axiemac_bus_reset(struct mii_dev *bus) 608 { 609 debug("axiemac: Bus reset\n"); 610 return 0; 611 } 612 613 int xilinx_axiemac_initialize(bd_t *bis, unsigned long base_addr, 614 unsigned long dma_addr) 615 { 616 struct eth_device *dev; 617 struct axidma_priv *priv; 618 619 dev = calloc(1, sizeof(struct eth_device)); 620 if (dev == NULL) 621 return -1; 622 623 dev->priv = calloc(1, sizeof(struct axidma_priv)); 624 if (dev->priv == NULL) { 625 free(dev); 626 return -1; 627 } 628 priv = dev->priv; 629 630 sprintf(dev->name, "aximac.%lx", base_addr); 631 632 dev->iobase = base_addr; 633 priv->dmatx = (struct axidma_reg *)dma_addr; 634 /* RX channel offset is 0x30 */ 635 priv->dmarx = (struct axidma_reg *)(dma_addr + 0x30); 636 dev->init = axiemac_init; 637 dev->halt = axiemac_halt; 638 dev->send = axiemac_send; 639 dev->recv = axiemac_recv; 640 dev->write_hwaddr = axiemac_setup_mac; 641 642 #ifdef CONFIG_PHY_ADDR 643 priv->phyaddr = CONFIG_PHY_ADDR; 644 #else 645 priv->phyaddr = -1; 646 #endif 647 648 eth_register(dev); 649 650 #if defined(CONFIG_MII) || defined(CONFIG_CMD_MII) || defined(CONFIG_PHYLIB) 651 miiphy_register(dev->name, axiemac_miiphy_read, axiemac_miiphy_write); 652 priv->bus = miiphy_get_dev_by_name(dev->name); 653 priv->bus->reset = axiemac_bus_reset; 654 #endif 655 return 1; 656 } 657