1 /* 2 * Marvell PHY drivers 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 * 6 * Copyright 2010-2011 Freescale Semiconductor, Inc. 7 * author Andy Fleming 8 */ 9 #include <config.h> 10 #include <common.h> 11 #include <errno.h> 12 #include <phy.h> 13 14 #define PHY_AUTONEGOTIATE_TIMEOUT 5000 15 16 #define MII_MARVELL_PHY_PAGE 22 17 18 /* 88E1011 PHY Status Register */ 19 #define MIIM_88E1xxx_PHY_STATUS 0x11 20 #define MIIM_88E1xxx_PHYSTAT_SPEED 0xc000 21 #define MIIM_88E1xxx_PHYSTAT_GBIT 0x8000 22 #define MIIM_88E1xxx_PHYSTAT_100 0x4000 23 #define MIIM_88E1xxx_PHYSTAT_DUPLEX 0x2000 24 #define MIIM_88E1xxx_PHYSTAT_SPDDONE 0x0800 25 #define MIIM_88E1xxx_PHYSTAT_LINK 0x0400 26 27 #define MIIM_88E1xxx_PHY_SCR 0x10 28 #define MIIM_88E1xxx_PHY_MDI_X_AUTO 0x0060 29 30 /* 88E1111 PHY LED Control Register */ 31 #define MIIM_88E1111_PHY_LED_CONTROL 24 32 #define MIIM_88E1111_PHY_LED_DIRECT 0x4100 33 #define MIIM_88E1111_PHY_LED_COMBINE 0x411C 34 35 /* 88E1111 Extended PHY Specific Control Register */ 36 #define MIIM_88E1111_PHY_EXT_CR 0x14 37 #define MIIM_88E1111_RX_DELAY 0x80 38 #define MIIM_88E1111_TX_DELAY 0x2 39 40 /* 88E1111 Extended PHY Specific Status Register */ 41 #define MIIM_88E1111_PHY_EXT_SR 0x1b 42 #define MIIM_88E1111_HWCFG_MODE_MASK 0xf 43 #define MIIM_88E1111_HWCFG_MODE_COPPER_RGMII 0xb 44 #define MIIM_88E1111_HWCFG_MODE_FIBER_RGMII 0x3 45 #define MIIM_88E1111_HWCFG_MODE_SGMII_NO_CLK 0x4 46 #define MIIM_88E1111_HWCFG_MODE_COPPER_RTBI 0x9 47 #define MIIM_88E1111_HWCFG_FIBER_COPPER_AUTO 0x8000 48 #define MIIM_88E1111_HWCFG_FIBER_COPPER_RES 0x2000 49 50 #define MIIM_88E1111_COPPER 0 51 #define MIIM_88E1111_FIBER 1 52 53 /* 88E1118 PHY defines */ 54 #define MIIM_88E1118_PHY_PAGE 22 55 #define MIIM_88E1118_PHY_LED_PAGE 3 56 57 /* 88E1121 PHY LED Control Register */ 58 #define MIIM_88E1121_PHY_LED_CTRL 16 59 #define MIIM_88E1121_PHY_LED_PAGE 3 60 #define MIIM_88E1121_PHY_LED_DEF 0x0030 61 62 /* 88E1121 PHY IRQ Enable/Status Register */ 63 #define MIIM_88E1121_PHY_IRQ_EN 18 64 #define MIIM_88E1121_PHY_IRQ_STATUS 19 65 66 #define MIIM_88E1121_PHY_PAGE 22 67 68 /* 88E1145 Extended PHY Specific Control Register */ 69 #define MIIM_88E1145_PHY_EXT_CR 20 70 #define MIIM_M88E1145_RGMII_RX_DELAY 0x0080 71 #define MIIM_M88E1145_RGMII_TX_DELAY 0x0002 72 73 #define MIIM_88E1145_PHY_LED_CONTROL 24 74 #define MIIM_88E1145_PHY_LED_DIRECT 0x4100 75 76 #define MIIM_88E1145_PHY_PAGE 29 77 #define MIIM_88E1145_PHY_CAL_OV 30 78 79 #define MIIM_88E1149_PHY_PAGE 29 80 81 /* 88E1310 PHY defines */ 82 #define MIIM_88E1310_PHY_LED_CTRL 16 83 #define MIIM_88E1310_PHY_IRQ_EN 18 84 #define MIIM_88E1310_PHY_RGMII_CTRL 21 85 #define MIIM_88E1310_PHY_PAGE 22 86 87 /* 88E151x PHY defines */ 88 /* Page 2 registers */ 89 #define MIIM_88E151x_PHY_MSCR 21 90 #define MIIM_88E151x_RGMII_RX_DELAY BIT(5) 91 #define MIIM_88E151x_RGMII_TX_DELAY BIT(4) 92 #define MIIM_88E151x_RGMII_RXTX_DELAY (BIT(5) | BIT(4)) 93 /* Page 3 registers */ 94 #define MIIM_88E151x_LED_FUNC_CTRL 16 95 #define MIIM_88E151x_LED_FLD_SZ 4 96 #define MIIM_88E151x_LED0_OFFS (0 * MIIM_88E151x_LED_FLD_SZ) 97 #define MIIM_88E151x_LED1_OFFS (1 * MIIM_88E151x_LED_FLD_SZ) 98 #define MIIM_88E151x_LED0_ACT 3 99 #define MIIM_88E151x_LED1_100_1000_LINK 6 100 #define MIIM_88E151x_LED_TIMER_CTRL 18 101 #define MIIM_88E151x_INT_EN_OFFS 7 102 /* Page 18 registers */ 103 #define MIIM_88E151x_GENERAL_CTRL 20 104 #define MIIM_88E151x_MODE_SGMII 1 105 #define MIIM_88E151x_RESET_OFFS 15 106 107 /* Marvell 88E1011S */ 108 static int m88e1011s_config(struct phy_device *phydev) 109 { 110 /* Reset and configure the PHY */ 111 phy_write(phydev, MDIO_DEVAD_NONE, MII_BMCR, BMCR_RESET); 112 113 phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x1f); 114 phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x200c); 115 phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5); 116 phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0); 117 phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100); 118 119 phy_write(phydev, MDIO_DEVAD_NONE, MII_BMCR, BMCR_RESET); 120 121 genphy_config_aneg(phydev); 122 123 return 0; 124 } 125 126 /* Parse the 88E1011's status register for speed and duplex 127 * information 128 */ 129 static int m88e1xxx_parse_status(struct phy_device *phydev) 130 { 131 unsigned int speed; 132 unsigned int mii_reg; 133 134 mii_reg = phy_read(phydev, MDIO_DEVAD_NONE, MIIM_88E1xxx_PHY_STATUS); 135 136 if ((mii_reg & MIIM_88E1xxx_PHYSTAT_LINK) && 137 !(mii_reg & MIIM_88E1xxx_PHYSTAT_SPDDONE)) { 138 int i = 0; 139 140 puts("Waiting for PHY realtime link"); 141 while (!(mii_reg & MIIM_88E1xxx_PHYSTAT_SPDDONE)) { 142 /* Timeout reached ? */ 143 if (i > PHY_AUTONEGOTIATE_TIMEOUT) { 144 puts(" TIMEOUT !\n"); 145 phydev->link = 0; 146 return -ETIMEDOUT; 147 } 148 149 if ((i++ % 1000) == 0) 150 putc('.'); 151 udelay(1000); 152 mii_reg = phy_read(phydev, MDIO_DEVAD_NONE, 153 MIIM_88E1xxx_PHY_STATUS); 154 } 155 puts(" done\n"); 156 udelay(500000); /* another 500 ms (results in faster booting) */ 157 } else { 158 if (mii_reg & MIIM_88E1xxx_PHYSTAT_LINK) 159 phydev->link = 1; 160 else 161 phydev->link = 0; 162 } 163 164 if (mii_reg & MIIM_88E1xxx_PHYSTAT_DUPLEX) 165 phydev->duplex = DUPLEX_FULL; 166 else 167 phydev->duplex = DUPLEX_HALF; 168 169 speed = mii_reg & MIIM_88E1xxx_PHYSTAT_SPEED; 170 171 switch (speed) { 172 case MIIM_88E1xxx_PHYSTAT_GBIT: 173 phydev->speed = SPEED_1000; 174 break; 175 case MIIM_88E1xxx_PHYSTAT_100: 176 phydev->speed = SPEED_100; 177 break; 178 default: 179 phydev->speed = SPEED_10; 180 break; 181 } 182 183 return 0; 184 } 185 186 static int m88e1011s_startup(struct phy_device *phydev) 187 { 188 int ret; 189 190 ret = genphy_update_link(phydev); 191 if (ret) 192 return ret; 193 194 return m88e1xxx_parse_status(phydev); 195 } 196 197 /* Marvell 88E1111S */ 198 static int m88e1111s_config(struct phy_device *phydev) 199 { 200 int reg; 201 202 if (phy_interface_is_rgmii(phydev)) { 203 reg = phy_read(phydev, 204 MDIO_DEVAD_NONE, MIIM_88E1111_PHY_EXT_CR); 205 if ((phydev->interface == PHY_INTERFACE_MODE_RGMII) || 206 (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID)) { 207 reg |= (MIIM_88E1111_RX_DELAY | MIIM_88E1111_TX_DELAY); 208 } else if (phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID) { 209 reg &= ~MIIM_88E1111_TX_DELAY; 210 reg |= MIIM_88E1111_RX_DELAY; 211 } else if (phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID) { 212 reg &= ~MIIM_88E1111_RX_DELAY; 213 reg |= MIIM_88E1111_TX_DELAY; 214 } 215 216 phy_write(phydev, 217 MDIO_DEVAD_NONE, MIIM_88E1111_PHY_EXT_CR, reg); 218 219 reg = phy_read(phydev, 220 MDIO_DEVAD_NONE, MIIM_88E1111_PHY_EXT_SR); 221 222 reg &= ~(MIIM_88E1111_HWCFG_MODE_MASK); 223 224 if (reg & MIIM_88E1111_HWCFG_FIBER_COPPER_RES) 225 reg |= MIIM_88E1111_HWCFG_MODE_FIBER_RGMII; 226 else 227 reg |= MIIM_88E1111_HWCFG_MODE_COPPER_RGMII; 228 229 phy_write(phydev, 230 MDIO_DEVAD_NONE, MIIM_88E1111_PHY_EXT_SR, reg); 231 } 232 233 if (phydev->interface == PHY_INTERFACE_MODE_SGMII) { 234 reg = phy_read(phydev, 235 MDIO_DEVAD_NONE, MIIM_88E1111_PHY_EXT_SR); 236 237 reg &= ~(MIIM_88E1111_HWCFG_MODE_MASK); 238 reg |= MIIM_88E1111_HWCFG_MODE_SGMII_NO_CLK; 239 reg |= MIIM_88E1111_HWCFG_FIBER_COPPER_AUTO; 240 241 phy_write(phydev, MDIO_DEVAD_NONE, 242 MIIM_88E1111_PHY_EXT_SR, reg); 243 } 244 245 if (phydev->interface == PHY_INTERFACE_MODE_RTBI) { 246 reg = phy_read(phydev, 247 MDIO_DEVAD_NONE, MIIM_88E1111_PHY_EXT_CR); 248 reg |= (MIIM_88E1111_RX_DELAY | MIIM_88E1111_TX_DELAY); 249 phy_write(phydev, 250 MDIO_DEVAD_NONE, MIIM_88E1111_PHY_EXT_CR, reg); 251 252 reg = phy_read(phydev, MDIO_DEVAD_NONE, 253 MIIM_88E1111_PHY_EXT_SR); 254 reg &= ~(MIIM_88E1111_HWCFG_MODE_MASK | 255 MIIM_88E1111_HWCFG_FIBER_COPPER_RES); 256 reg |= 0x7 | MIIM_88E1111_HWCFG_FIBER_COPPER_AUTO; 257 phy_write(phydev, MDIO_DEVAD_NONE, 258 MIIM_88E1111_PHY_EXT_SR, reg); 259 260 /* soft reset */ 261 phy_reset(phydev); 262 263 reg = phy_read(phydev, MDIO_DEVAD_NONE, 264 MIIM_88E1111_PHY_EXT_SR); 265 reg &= ~(MIIM_88E1111_HWCFG_MODE_MASK | 266 MIIM_88E1111_HWCFG_FIBER_COPPER_RES); 267 reg |= MIIM_88E1111_HWCFG_MODE_COPPER_RTBI | 268 MIIM_88E1111_HWCFG_FIBER_COPPER_AUTO; 269 phy_write(phydev, MDIO_DEVAD_NONE, 270 MIIM_88E1111_PHY_EXT_SR, reg); 271 } 272 273 /* soft reset */ 274 phy_reset(phydev); 275 276 genphy_config_aneg(phydev); 277 genphy_restart_aneg(phydev); 278 279 return 0; 280 } 281 282 /** 283 * m88e1518_phy_writebits - write bits to a register 284 */ 285 void m88e1518_phy_writebits(struct phy_device *phydev, 286 u8 reg_num, u16 offset, u16 len, u16 data) 287 { 288 u16 reg, mask; 289 290 if ((len + offset) >= 16) 291 mask = 0 - (1 << offset); 292 else 293 mask = (1 << (len + offset)) - (1 << offset); 294 295 reg = phy_read(phydev, MDIO_DEVAD_NONE, reg_num); 296 297 reg &= ~mask; 298 reg |= data << offset; 299 300 phy_write(phydev, MDIO_DEVAD_NONE, reg_num, reg); 301 } 302 303 static int m88e1518_config(struct phy_device *phydev) 304 { 305 u16 reg; 306 307 /* 308 * As per Marvell Release Notes - Alaska 88E1510/88E1518/88E1512 309 * /88E1514 Rev A0, Errata Section 3.1 310 */ 311 312 /* EEE initialization */ 313 phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1118_PHY_PAGE, 0x00ff); 314 phy_write(phydev, MDIO_DEVAD_NONE, 17, 0x214B); 315 phy_write(phydev, MDIO_DEVAD_NONE, 16, 0x2144); 316 phy_write(phydev, MDIO_DEVAD_NONE, 17, 0x0C28); 317 phy_write(phydev, MDIO_DEVAD_NONE, 16, 0x2146); 318 phy_write(phydev, MDIO_DEVAD_NONE, 17, 0xB233); 319 phy_write(phydev, MDIO_DEVAD_NONE, 16, 0x214D); 320 phy_write(phydev, MDIO_DEVAD_NONE, 17, 0xCC0C); 321 phy_write(phydev, MDIO_DEVAD_NONE, 16, 0x2159); 322 phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1118_PHY_PAGE, 0x0000); 323 324 /* SGMII-to-Copper mode initialization */ 325 if (phydev->interface == PHY_INTERFACE_MODE_SGMII) { 326 /* Select page 18 */ 327 phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1118_PHY_PAGE, 18); 328 329 /* In reg 20, write MODE[2:0] = 0x1 (SGMII to Copper) */ 330 m88e1518_phy_writebits(phydev, MIIM_88E151x_GENERAL_CTRL, 331 0, 3, MIIM_88E151x_MODE_SGMII); 332 333 /* PHY reset is necessary after changing MODE[2:0] */ 334 m88e1518_phy_writebits(phydev, MIIM_88E151x_GENERAL_CTRL, 335 MIIM_88E151x_RESET_OFFS, 1, 1); 336 337 /* Reset page selection */ 338 phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1118_PHY_PAGE, 0); 339 340 udelay(100); 341 } 342 343 if (phydev->interface == PHY_INTERFACE_MODE_SGMII) { 344 reg = phy_read(phydev, MDIO_DEVAD_NONE, 345 MIIM_88E1111_PHY_EXT_SR); 346 347 reg &= ~(MIIM_88E1111_HWCFG_MODE_MASK); 348 reg |= MIIM_88E1111_HWCFG_MODE_SGMII_NO_CLK; 349 reg |= MIIM_88E1111_HWCFG_FIBER_COPPER_AUTO; 350 351 phy_write(phydev, MDIO_DEVAD_NONE, 352 MIIM_88E1111_PHY_EXT_SR, reg); 353 } 354 355 if (phy_interface_is_rgmii(phydev)) { 356 phy_write(phydev, MDIO_DEVAD_NONE, MII_MARVELL_PHY_PAGE, 2); 357 358 reg = phy_read(phydev, MDIO_DEVAD_NONE, MIIM_88E151x_PHY_MSCR); 359 reg &= ~MIIM_88E151x_RGMII_RXTX_DELAY; 360 if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID) 361 reg |= MIIM_88E151x_RGMII_RXTX_DELAY; 362 else if (phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID) 363 reg |= MIIM_88E151x_RGMII_RX_DELAY; 364 else if (phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID) 365 reg |= MIIM_88E151x_RGMII_TX_DELAY; 366 phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E151x_PHY_MSCR, reg); 367 368 phy_write(phydev, MDIO_DEVAD_NONE, MII_MARVELL_PHY_PAGE, 0); 369 } 370 371 /* soft reset */ 372 phy_reset(phydev); 373 374 genphy_config_aneg(phydev); 375 genphy_restart_aneg(phydev); 376 377 return 0; 378 } 379 380 /* Marvell 88E1510 */ 381 static int m88e1510_config(struct phy_device *phydev) 382 { 383 /* Select page 3 */ 384 phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1118_PHY_PAGE, 385 MIIM_88E1118_PHY_LED_PAGE); 386 387 /* Enable INTn output on LED[2] */ 388 m88e1518_phy_writebits(phydev, MIIM_88E151x_LED_TIMER_CTRL, 389 MIIM_88E151x_INT_EN_OFFS, 1, 1); 390 391 /* Configure LEDs */ 392 /* LED[0]:0011 (ACT) */ 393 m88e1518_phy_writebits(phydev, MIIM_88E151x_LED_FUNC_CTRL, 394 MIIM_88E151x_LED0_OFFS, MIIM_88E151x_LED_FLD_SZ, 395 MIIM_88E151x_LED0_ACT); 396 /* LED[1]:0110 (LINK 100/1000 Mbps) */ 397 m88e1518_phy_writebits(phydev, MIIM_88E151x_LED_FUNC_CTRL, 398 MIIM_88E151x_LED1_OFFS, MIIM_88E151x_LED_FLD_SZ, 399 MIIM_88E151x_LED1_100_1000_LINK); 400 401 /* Reset page selection */ 402 phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1118_PHY_PAGE, 0); 403 404 return m88e1518_config(phydev); 405 } 406 407 /* Marvell 88E1118 */ 408 static int m88e1118_config(struct phy_device *phydev) 409 { 410 /* Change Page Number */ 411 phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1118_PHY_PAGE, 0x0002); 412 /* Delay RGMII TX and RX */ 413 phy_write(phydev, MDIO_DEVAD_NONE, 0x15, 0x1070); 414 /* Change Page Number */ 415 phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1118_PHY_PAGE, 0x0003); 416 /* Adjust LED control */ 417 phy_write(phydev, MDIO_DEVAD_NONE, 0x10, 0x021e); 418 /* Change Page Number */ 419 phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1118_PHY_PAGE, 0x0000); 420 421 return genphy_config_aneg(phydev); 422 } 423 424 static int m88e1118_startup(struct phy_device *phydev) 425 { 426 int ret; 427 428 /* Change Page Number */ 429 phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1118_PHY_PAGE, 0x0000); 430 431 ret = genphy_update_link(phydev); 432 if (ret) 433 return ret; 434 435 return m88e1xxx_parse_status(phydev); 436 } 437 438 /* Marvell 88E1121R */ 439 static int m88e1121_config(struct phy_device *phydev) 440 { 441 int pg; 442 443 /* Configure the PHY */ 444 genphy_config_aneg(phydev); 445 446 /* Switch the page to access the led register */ 447 pg = phy_read(phydev, MDIO_DEVAD_NONE, MIIM_88E1121_PHY_PAGE); 448 phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1121_PHY_PAGE, 449 MIIM_88E1121_PHY_LED_PAGE); 450 /* Configure leds */ 451 phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1121_PHY_LED_CTRL, 452 MIIM_88E1121_PHY_LED_DEF); 453 /* Restore the page pointer */ 454 phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1121_PHY_PAGE, pg); 455 456 /* Disable IRQs and de-assert interrupt */ 457 phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1121_PHY_IRQ_EN, 0); 458 phy_read(phydev, MDIO_DEVAD_NONE, MIIM_88E1121_PHY_IRQ_STATUS); 459 460 return 0; 461 } 462 463 /* Marvell 88E1145 */ 464 static int m88e1145_config(struct phy_device *phydev) 465 { 466 int reg; 467 468 /* Errata E0, E1 */ 469 phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1145_PHY_PAGE, 0x001b); 470 phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1145_PHY_CAL_OV, 0x418f); 471 phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1145_PHY_PAGE, 0x0016); 472 phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1145_PHY_CAL_OV, 0xa2da); 473 474 phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1xxx_PHY_SCR, 475 MIIM_88E1xxx_PHY_MDI_X_AUTO); 476 477 reg = phy_read(phydev, MDIO_DEVAD_NONE, MIIM_88E1145_PHY_EXT_CR); 478 if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID) 479 reg |= MIIM_M88E1145_RGMII_RX_DELAY | 480 MIIM_M88E1145_RGMII_TX_DELAY; 481 phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1145_PHY_EXT_CR, reg); 482 483 genphy_config_aneg(phydev); 484 485 /* soft reset */ 486 reg = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMCR); 487 reg |= BMCR_RESET; 488 phy_write(phydev, MDIO_DEVAD_NONE, MII_BMCR, reg); 489 490 return 0; 491 } 492 493 static int m88e1145_startup(struct phy_device *phydev) 494 { 495 int ret; 496 497 ret = genphy_update_link(phydev); 498 if (ret) 499 return ret; 500 501 phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1145_PHY_LED_CONTROL, 502 MIIM_88E1145_PHY_LED_DIRECT); 503 return m88e1xxx_parse_status(phydev); 504 } 505 506 /* Marvell 88E1149S */ 507 static int m88e1149_config(struct phy_device *phydev) 508 { 509 phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1149_PHY_PAGE, 0x1f); 510 phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x200c); 511 phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1149_PHY_PAGE, 0x5); 512 phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x0); 513 phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100); 514 515 genphy_config_aneg(phydev); 516 517 phy_reset(phydev); 518 519 return 0; 520 } 521 522 /* Marvell 88E1310 */ 523 static int m88e1310_config(struct phy_device *phydev) 524 { 525 u16 reg; 526 527 /* LED link and activity */ 528 phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1310_PHY_PAGE, 0x0003); 529 reg = phy_read(phydev, MDIO_DEVAD_NONE, MIIM_88E1310_PHY_LED_CTRL); 530 reg = (reg & ~0xf) | 0x1; 531 phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1310_PHY_LED_CTRL, reg); 532 533 /* Set LED2/INT to INT mode, low active */ 534 phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1310_PHY_PAGE, 0x0003); 535 reg = phy_read(phydev, MDIO_DEVAD_NONE, MIIM_88E1310_PHY_IRQ_EN); 536 reg = (reg & 0x77ff) | 0x0880; 537 phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1310_PHY_IRQ_EN, reg); 538 539 /* Set RGMII delay */ 540 phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1310_PHY_PAGE, 0x0002); 541 reg = phy_read(phydev, MDIO_DEVAD_NONE, MIIM_88E1310_PHY_RGMII_CTRL); 542 reg |= 0x0030; 543 phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1310_PHY_RGMII_CTRL, reg); 544 545 /* Ensure to return to page 0 */ 546 phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1310_PHY_PAGE, 0x0000); 547 548 return genphy_config_aneg(phydev); 549 } 550 551 static int m88e1680_config(struct phy_device *phydev) 552 { 553 /* 554 * As per Marvell Release Notes - Alaska V 88E1680 Rev A2 555 * Errata Section 4.1 556 */ 557 u16 reg; 558 int res; 559 560 /* Matrix LED mode (not neede if single LED mode is used */ 561 phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1118_PHY_PAGE, 0x0004); 562 reg = phy_read(phydev, MDIO_DEVAD_NONE, 27); 563 reg |= (1 << 5); 564 phy_write(phydev, MDIO_DEVAD_NONE, 27, reg); 565 566 /* QSGMII TX amplitude change */ 567 phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1118_PHY_PAGE, 0x00fd); 568 phy_write(phydev, MDIO_DEVAD_NONE, 8, 0x0b53); 569 phy_write(phydev, MDIO_DEVAD_NONE, 7, 0x200d); 570 phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1118_PHY_PAGE, 0x0000); 571 572 /* EEE initialization */ 573 phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1118_PHY_PAGE, 0x00ff); 574 phy_write(phydev, MDIO_DEVAD_NONE, 17, 0xb030); 575 phy_write(phydev, MDIO_DEVAD_NONE, 16, 0x215c); 576 phy_write(phydev, MDIO_DEVAD_NONE, 22, 0x00fc); 577 phy_write(phydev, MDIO_DEVAD_NONE, 24, 0x888c); 578 phy_write(phydev, MDIO_DEVAD_NONE, 25, 0x888c); 579 phy_write(phydev, MDIO_DEVAD_NONE, MIIM_88E1118_PHY_PAGE, 0x0000); 580 phy_write(phydev, MDIO_DEVAD_NONE, 0, 0x9140); 581 582 res = genphy_config_aneg(phydev); 583 if (res < 0) 584 return res; 585 586 /* soft reset */ 587 reg = phy_read(phydev, MDIO_DEVAD_NONE, MII_BMCR); 588 reg |= BMCR_RESET; 589 phy_write(phydev, MDIO_DEVAD_NONE, MII_BMCR, reg); 590 591 return 0; 592 } 593 594 static struct phy_driver M88E1011S_driver = { 595 .name = "Marvell 88E1011S", 596 .uid = 0x1410c60, 597 .mask = 0xffffff0, 598 .features = PHY_GBIT_FEATURES, 599 .config = &m88e1011s_config, 600 .startup = &m88e1011s_startup, 601 .shutdown = &genphy_shutdown, 602 }; 603 604 static struct phy_driver M88E1111S_driver = { 605 .name = "Marvell 88E1111S", 606 .uid = 0x1410cc0, 607 .mask = 0xffffff0, 608 .features = PHY_GBIT_FEATURES, 609 .config = &m88e1111s_config, 610 .startup = &m88e1011s_startup, 611 .shutdown = &genphy_shutdown, 612 }; 613 614 static struct phy_driver M88E1118_driver = { 615 .name = "Marvell 88E1118", 616 .uid = 0x1410e10, 617 .mask = 0xffffff0, 618 .features = PHY_GBIT_FEATURES, 619 .config = &m88e1118_config, 620 .startup = &m88e1118_startup, 621 .shutdown = &genphy_shutdown, 622 }; 623 624 static struct phy_driver M88E1118R_driver = { 625 .name = "Marvell 88E1118R", 626 .uid = 0x1410e40, 627 .mask = 0xffffff0, 628 .features = PHY_GBIT_FEATURES, 629 .config = &m88e1118_config, 630 .startup = &m88e1118_startup, 631 .shutdown = &genphy_shutdown, 632 }; 633 634 static struct phy_driver M88E1121R_driver = { 635 .name = "Marvell 88E1121R", 636 .uid = 0x1410cb0, 637 .mask = 0xffffff0, 638 .features = PHY_GBIT_FEATURES, 639 .config = &m88e1121_config, 640 .startup = &genphy_startup, 641 .shutdown = &genphy_shutdown, 642 }; 643 644 static struct phy_driver M88E1145_driver = { 645 .name = "Marvell 88E1145", 646 .uid = 0x1410cd0, 647 .mask = 0xffffff0, 648 .features = PHY_GBIT_FEATURES, 649 .config = &m88e1145_config, 650 .startup = &m88e1145_startup, 651 .shutdown = &genphy_shutdown, 652 }; 653 654 static struct phy_driver M88E1149S_driver = { 655 .name = "Marvell 88E1149S", 656 .uid = 0x1410ca0, 657 .mask = 0xffffff0, 658 .features = PHY_GBIT_FEATURES, 659 .config = &m88e1149_config, 660 .startup = &m88e1011s_startup, 661 .shutdown = &genphy_shutdown, 662 }; 663 664 static struct phy_driver M88E1510_driver = { 665 .name = "Marvell 88E1510", 666 .uid = 0x1410dd0, 667 .mask = 0xfffffff, 668 .features = PHY_GBIT_FEATURES, 669 .config = &m88e1510_config, 670 .startup = &m88e1011s_startup, 671 .shutdown = &genphy_shutdown, 672 }; 673 674 /* 675 * This supports: 676 * 88E1518, uid 0x1410dd1 677 * 88E1512, uid 0x1410dd4 678 */ 679 static struct phy_driver M88E1518_driver = { 680 .name = "Marvell 88E1518", 681 .uid = 0x1410dd0, 682 .mask = 0xffffffa, 683 .features = PHY_GBIT_FEATURES, 684 .config = &m88e1518_config, 685 .startup = &m88e1011s_startup, 686 .shutdown = &genphy_shutdown, 687 }; 688 689 static struct phy_driver M88E1310_driver = { 690 .name = "Marvell 88E1310", 691 .uid = 0x01410e90, 692 .mask = 0xffffff0, 693 .features = PHY_GBIT_FEATURES, 694 .config = &m88e1310_config, 695 .startup = &m88e1011s_startup, 696 .shutdown = &genphy_shutdown, 697 }; 698 699 static struct phy_driver M88E1680_driver = { 700 .name = "Marvell 88E1680", 701 .uid = 0x1410ed0, 702 .mask = 0xffffff0, 703 .features = PHY_GBIT_FEATURES, 704 .config = &m88e1680_config, 705 .startup = &genphy_startup, 706 .shutdown = &genphy_shutdown, 707 }; 708 709 int phy_marvell_init(void) 710 { 711 phy_register(&M88E1310_driver); 712 phy_register(&M88E1149S_driver); 713 phy_register(&M88E1145_driver); 714 phy_register(&M88E1121R_driver); 715 phy_register(&M88E1118_driver); 716 phy_register(&M88E1118R_driver); 717 phy_register(&M88E1111S_driver); 718 phy_register(&M88E1011S_driver); 719 phy_register(&M88E1510_driver); 720 phy_register(&M88E1518_driver); 721 phy_register(&M88E1680_driver); 722 723 return 0; 724 } 725