1 2config BITBANGMII 3 bool "Bit-banged ethernet MII management channel support" 4 5config MV88E6352_SWITCH 6 bool "Marvell 88E6352 switch support" 7 8menuconfig PHYLIB 9 bool "Ethernet PHY (physical media interface) support" 10 depends on NET 11 help 12 Enable Ethernet PHY (physical media interface) support. 13 14if PHYLIB 15 16config PHY_ADDR_ENABLE 17 bool "Limit phy address" 18 default y if ARCH_SUNXI 19 help 20 Select this if you want to control which phy address is used 21 22if PHY_ADDR_ENABLE 23config PHY_ADDR 24 int "PHY address" 25 default 1 if ARCH_SUNXI 26 default 0 27 help 28 The address of PHY on MII bus. Usually in range of 0 to 31. 29endif 30 31config B53_SWITCH 32 bool "Broadcom BCM53xx (RoboSwitch) Ethernet switch PHY support." 33 help 34 Enable support for Broadcom BCM53xx (RoboSwitch) Ethernet switches. 35 This currently supports BCM53125 and similar models. 36 37if B53_SWITCH 38 39config B53_CPU_PORT 40 int "CPU port" 41 default 8 42 43config B53_PHY_PORTS 44 hex "Bitmask of PHY ports" 45 46endif # B53_SWITCH 47 48config MV88E61XX_SWITCH 49 bool "Marvel MV88E61xx Ethernet switch PHY support." 50 51if MV88E61XX_SWITCH 52 53config MV88E61XX_CPU_PORT 54 int "CPU Port" 55 56config MV88E61XX_PHY_PORTS 57 hex "Bitmask of PHY Ports" 58 59config MV88E61XX_FIXED_PORTS 60 hex "Bitmask of PHYless serdes Ports" 61 62endif # MV88E61XX_SWITCH 63 64config PHYLIB_10G 65 bool "Generic 10G PHY support" 66 67menuconfig PHY_AQUANTIA 68 bool "Aquantia Ethernet PHYs support" 69 select PHY_GIGE 70 select PHYLIB_10G 71 72config PHY_AQUANTIA_UPLOAD_FW 73 bool "Aquantia firmware loading support" 74 default n 75 depends on PHY_AQUANTIA 76 help 77 Aquantia PHYs use firmware which can be either loaded automatically 78 from storage directly attached to the phy or loaded by the boot loader 79 via MDIO commands. The firmware is loaded from a file, specified by 80 the PHY_AQUANTIA_FW_PART and PHY_AQUANTIA_FW_NAME options. 81 82config PHY_AQUANTIA_FW_PART 83 string "Aquantia firmware partition" 84 depends on PHY_AQUANTIA_UPLOAD_FW 85 help 86 Partition containing the firmware file. 87 88config PHY_AQUANTIA_FW_NAME 89 string "Aquantia firmware filename" 90 depends on PHY_AQUANTIA_UPLOAD_FW 91 help 92 Firmware filename. 93 94config PHY_ATHEROS 95 bool "Atheros Ethernet PHYs support" 96 97config PHY_BROADCOM 98 bool "Broadcom Ethernet PHYs support" 99 100config PHY_CORTINA 101 bool "Cortina Ethernet PHYs support" 102 103config PHY_DAVICOM 104 bool "Davicom Ethernet PHYs support" 105 106config PHY_ET1011C 107 bool "LSI TruePHY ET1011C support" 108 109config PHY_LXT 110 bool "LXT971 Ethernet PHY support" 111 112config PHY_MARVELL 113 bool "Marvell Ethernet PHYs support" 114 115config PHY_MESON_GXL 116 bool "Amlogic Meson GXL Internal PHY support" 117 118config PHY_MICREL 119 bool "Micrel Ethernet PHYs support" 120 help 121 Enable support for the GbE PHYs manufactured by Micrel (now 122 a part of Microchip). This includes drivers for the KSZ804, 123 KSZ8031, KSZ8051, KSZ8081, KSZ8895, KSZ886x, KSZ8721 124 either/or KSZ9021 (see the "Micrel KSZ9021 family support" 125 config option for details), and KSZ9031 (if configured). 126 127if PHY_MICREL 128 129config PHY_MICREL_KSZ9021 130 bool 131 select PHY_GIGE 132 select PHY_MICREL_KSZ90X1 133 134config PHY_MICREL_KSZ9031 135 bool 136 select PHY_GIGE 137 select PHY_MICREL_KSZ90X1 138 139config PHY_MICREL_KSZ90X1 140 bool "Micrel KSZ90x1 family support" 141 select PHY_GIGE 142 help 143 Enable support for the Micrel KSZ9021 and KSZ9031 GbE PHYs. If 144 enabled, the extended register read/write for KSZ90x1 PHYs 145 is supported through the 'mdio' command and any RGMII signal 146 delays configured in the device tree will be applied to the 147 PHY during initialization. 148 149 This should not be enabled at the same time with PHY_MICREL_KSZ8XXX 150 as the KSZ9021 and KS8721 share the same ID. 151 152config PHY_MICREL_KSZ8XXX 153 bool "Micrel KSZ8xxx family support" 154 default y if !PHY_MICREL_KSZ90X1 155 help 156 Enable support for the 8000 series GbE PHYs manufactured by Micrel 157 (now a part of Microchip). This includes drivers for the KSZ804, 158 KSZ8031, KSZ8051, KSZ8081, KSZ8895, KSZ886x, and KSZ8721. 159 160 This should not be enabled at the same time with PHY_MICREL_KSZ90X1 161 as the KSZ9021 and KS8721 share the same ID. 162 163endif # PHY_MICREL 164 165config PHY_MSCC 166 bool "Microsemi Corp Ethernet PHYs support" 167 168config PHY_NATSEMI 169 bool "National Semiconductor Ethernet PHYs support" 170 171config PHY_REALTEK 172 bool "Realtek Ethernet PHYs support" 173 174config RTL8211E_PINE64_GIGABIT_FIX 175 bool "Fix gigabit throughput on some Pine64+ models" 176 depends on PHY_REALTEK 177 help 178 Configure the Realtek RTL8211E found on some Pine64+ models differently to 179 fix throughput on Gigabit links, turning off all internal delays in the 180 process. The settings that this touches are not documented in the CONFREG 181 section of the RTL8211E datasheet, but come from Realtek by way of the 182 Pine64 engineering team. 183 184config RTL8211X_PHY_FORCE_MASTER 185 bool "Ethernet PHY RTL8211x: force 1000BASE-T master mode" 186 depends on PHY_REALTEK 187 help 188 Force master mode for 1000BASE-T on RTl8211x PHYs (except for RTL8211F). 189 This can work around link stability and data corruption issues on gigabit 190 links which can occur in slave mode on certain PHYs, e.g. on the 191 RTL8211C(L). 192 193 Please note that two directly connected devices (i.e. via crossover cable) 194 will not be able to establish a link between each other if they both force 195 master mode. Multiple devices forcing master mode when connected by a 196 network switch do not pose a problem as the switch configures its affected 197 ports into slave mode. 198 199 This option only affects gigabit links. If you must establish a direct 200 connection between two devices which both force master mode, try forcing 201 the link speed to 100MBit/s. 202 203 If unsure, say N. 204 205config PHY_SMSC 206 bool "Microchip(SMSC) Ethernet PHYs support" 207 208config PHY_TERANETICS 209 bool "Teranetics Ethernet PHYs support" 210 211config PHY_TI 212 bool "Texas Instruments Ethernet PHYs support" 213 214config PHY_VITESSE 215 bool "Vitesse Ethernet PHYs support" 216 217config PHY_XILINX 218 bool "Xilinx Ethernet PHYs support" 219 220config PHY_FIXED 221 bool "Fixed-Link PHY" 222 depends on DM_ETH 223 help 224 Fixed PHY is used for having a 'fixed-link' to another MAC with a direct 225 connection (MII, RGMII, ...). 226 There is nothing like autoneogation and so 227 on, the link is always up with fixed speed and fixed duplex-setting. 228 More information: doc/device-tree-bindings/net/fixed-link.txt 229 230config PHY_NCSI 231 bool "NC-SI based PHY" 232 depends on DM_ETH 233 234endif #PHYLIB 235