xref: /openbmc/u-boot/drivers/net/pcnet.c (revision 93322749)
1 /*
2  * (C) Copyright 2002 Wolfgang Grandegger, wg@denx.de.
3  *
4  * This driver for AMD PCnet network controllers is derived from the
5  * Linux driver pcnet32.c written 1996-1999 by Thomas Bogendoerfer.
6  *
7  * SPDX-License-Identifier:	GPL-2.0+
8  */
9 
10 #include <common.h>
11 #include <malloc.h>
12 #include <net.h>
13 #include <netdev.h>
14 #include <asm/io.h>
15 #include <pci.h>
16 
17 #define	PCNET_DEBUG_LEVEL	0	/* 0=off, 1=init, 2=rx/tx */
18 
19 #define PCNET_DEBUG1(fmt,args...)	\
20 	debug_cond(PCNET_DEBUG_LEVEL > 0, fmt ,##args)
21 #define PCNET_DEBUG2(fmt,args...)	\
22 	debug_cond(PCNET_DEBUG_LEVEL > 1, fmt ,##args)
23 
24 #if !defined(CONF_PCNET_79C973) && defined(CONF_PCNET_79C975)
25 #error "Macro for PCnet chip version is not defined!"
26 #endif
27 
28 /*
29  * Set the number of Tx and Rx buffers, using Log_2(# buffers).
30  * Reasonable default values are 4 Tx buffers, and 16 Rx buffers.
31  * That translates to 2 (4 == 2^^2) and 4 (16 == 2^^4).
32  */
33 #define PCNET_LOG_TX_BUFFERS	0
34 #define PCNET_LOG_RX_BUFFERS	2
35 
36 #define TX_RING_SIZE		(1 << (PCNET_LOG_TX_BUFFERS))
37 #define TX_RING_LEN_BITS	((PCNET_LOG_TX_BUFFERS) << 12)
38 
39 #define RX_RING_SIZE		(1 << (PCNET_LOG_RX_BUFFERS))
40 #define RX_RING_LEN_BITS	((PCNET_LOG_RX_BUFFERS) << 4)
41 
42 #define PKT_BUF_SZ		1544
43 
44 /* The PCNET Rx and Tx ring descriptors. */
45 struct pcnet_rx_head {
46 	u32 base;
47 	s16 buf_length;
48 	s16 status;
49 	u32 msg_length;
50 	u32 reserved;
51 };
52 
53 struct pcnet_tx_head {
54 	u32 base;
55 	s16 length;
56 	s16 status;
57 	u32 misc;
58 	u32 reserved;
59 };
60 
61 /* The PCNET 32-Bit initialization block, described in databook. */
62 struct pcnet_init_block {
63 	u16 mode;
64 	u16 tlen_rlen;
65 	u8 phys_addr[6];
66 	u16 reserved;
67 	u32 filter[2];
68 	/* Receive and transmit ring base, along with extra bits. */
69 	u32 rx_ring;
70 	u32 tx_ring;
71 	u32 reserved2;
72 };
73 
74 struct pcnet_uncached_priv {
75 	struct pcnet_rx_head rx_ring[RX_RING_SIZE];
76 	struct pcnet_tx_head tx_ring[TX_RING_SIZE];
77 	struct pcnet_init_block init_block;
78 };
79 
80 typedef struct pcnet_priv {
81 	struct pcnet_uncached_priv *uc;
82 	/* Receive Buffer space */
83 	unsigned char (*rx_buf)[RX_RING_SIZE][PKT_BUF_SZ + 4];
84 	int cur_rx;
85 	int cur_tx;
86 } pcnet_priv_t;
87 
88 static pcnet_priv_t *lp;
89 
90 /* Offsets from base I/O address for WIO mode */
91 #define PCNET_RDP		0x10
92 #define PCNET_RAP		0x12
93 #define PCNET_RESET		0x14
94 #define PCNET_BDP		0x16
95 
96 static u16 pcnet_read_csr(struct eth_device *dev, int index)
97 {
98 	outw(index, dev->iobase + PCNET_RAP);
99 	return inw(dev->iobase + PCNET_RDP);
100 }
101 
102 static void pcnet_write_csr(struct eth_device *dev, int index, u16 val)
103 {
104 	outw(index, dev->iobase + PCNET_RAP);
105 	outw(val, dev->iobase + PCNET_RDP);
106 }
107 
108 static u16 pcnet_read_bcr(struct eth_device *dev, int index)
109 {
110 	outw(index, dev->iobase + PCNET_RAP);
111 	return inw(dev->iobase + PCNET_BDP);
112 }
113 
114 static void pcnet_write_bcr(struct eth_device *dev, int index, u16 val)
115 {
116 	outw(index, dev->iobase + PCNET_RAP);
117 	outw(val, dev->iobase + PCNET_BDP);
118 }
119 
120 static void pcnet_reset(struct eth_device *dev)
121 {
122 	inw(dev->iobase + PCNET_RESET);
123 }
124 
125 static int pcnet_check(struct eth_device *dev)
126 {
127 	outw(88, dev->iobase + PCNET_RAP);
128 	return inw(dev->iobase + PCNET_RAP) == 88;
129 }
130 
131 static int pcnet_init (struct eth_device *dev, bd_t * bis);
132 static int pcnet_send(struct eth_device *dev, void *packet, int length);
133 static int pcnet_recv (struct eth_device *dev);
134 static void pcnet_halt (struct eth_device *dev);
135 static int pcnet_probe (struct eth_device *dev, bd_t * bis, int dev_num);
136 
137 #define PCI_TO_MEM(d, a) pci_virt_to_mem((pci_dev_t)d->priv, (a))
138 #define PCI_TO_MEM_LE(d,a) (u32)(cpu_to_le32(PCI_TO_MEM(d,a)))
139 
140 static struct pci_device_id supported[] = {
141 	{PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_LANCE},
142 	{}
143 };
144 
145 
146 int pcnet_initialize(bd_t *bis)
147 {
148 	pci_dev_t devbusfn;
149 	struct eth_device *dev;
150 	u16 command, status;
151 	int dev_nr = 0;
152 
153 	PCNET_DEBUG1("\npcnet_initialize...\n");
154 
155 	for (dev_nr = 0;; dev_nr++) {
156 
157 		/*
158 		 * Find the PCnet PCI device(s).
159 		 */
160 		devbusfn = pci_find_devices(supported, dev_nr);
161 		if (devbusfn < 0)
162 			break;
163 
164 		/*
165 		 * Allocate and pre-fill the device structure.
166 		 */
167 		dev = (struct eth_device *)malloc(sizeof(*dev));
168 		if (!dev) {
169 			printf("pcnet: Can not allocate memory\n");
170 			break;
171 		}
172 		memset(dev, 0, sizeof(*dev));
173 		dev->priv = (void *)devbusfn;
174 		sprintf(dev->name, "pcnet#%d", dev_nr);
175 
176 		/*
177 		 * Setup the PCI device.
178 		 */
179 		pci_read_config_dword(devbusfn, PCI_BASE_ADDRESS_0,
180 				      (unsigned int *)&dev->iobase);
181 		dev->iobase = pci_io_to_phys(devbusfn, dev->iobase);
182 		dev->iobase &= ~0xf;
183 
184 		PCNET_DEBUG1("%s: devbusfn=0x%x iobase=0x%x: ",
185 			     dev->name, devbusfn, dev->iobase);
186 
187 		command = PCI_COMMAND_IO | PCI_COMMAND_MASTER;
188 		pci_write_config_word(devbusfn, PCI_COMMAND, command);
189 		pci_read_config_word(devbusfn, PCI_COMMAND, &status);
190 		if ((status & command) != command) {
191 			printf("%s: Couldn't enable IO access or Bus Mastering\n",
192 			       dev->name);
193 			free(dev);
194 			continue;
195 		}
196 
197 		pci_write_config_byte(devbusfn, PCI_LATENCY_TIMER, 0x40);
198 
199 		/*
200 		 * Probe the PCnet chip.
201 		 */
202 		if (pcnet_probe(dev, bis, dev_nr) < 0) {
203 			free(dev);
204 			continue;
205 		}
206 
207 		/*
208 		 * Setup device structure and register the driver.
209 		 */
210 		dev->init = pcnet_init;
211 		dev->halt = pcnet_halt;
212 		dev->send = pcnet_send;
213 		dev->recv = pcnet_recv;
214 
215 		eth_register(dev);
216 	}
217 
218 	udelay(10 * 1000);
219 
220 	return dev_nr;
221 }
222 
223 static int pcnet_probe(struct eth_device *dev, bd_t *bis, int dev_nr)
224 {
225 	int chip_version;
226 	char *chipname;
227 
228 #ifdef PCNET_HAS_PROM
229 	int i;
230 #endif
231 
232 	/* Reset the PCnet controller */
233 	pcnet_reset(dev);
234 
235 	/* Check if register access is working */
236 	if (pcnet_read_csr(dev, 0) != 4 || !pcnet_check(dev)) {
237 		printf("%s: CSR register access check failed\n", dev->name);
238 		return -1;
239 	}
240 
241 	/* Identify the chip */
242 	chip_version =
243 		pcnet_read_csr(dev, 88) | (pcnet_read_csr(dev, 89) << 16);
244 	if ((chip_version & 0xfff) != 0x003)
245 		return -1;
246 	chip_version = (chip_version >> 12) & 0xffff;
247 	switch (chip_version) {
248 	case 0x2621:
249 		chipname = "PCnet/PCI II 79C970A";	/* PCI */
250 		break;
251 #ifdef CONFIG_PCNET_79C973
252 	case 0x2625:
253 		chipname = "PCnet/FAST III 79C973";	/* PCI */
254 		break;
255 #endif
256 #ifdef CONFIG_PCNET_79C975
257 	case 0x2627:
258 		chipname = "PCnet/FAST III 79C975";	/* PCI */
259 		break;
260 #endif
261 	default:
262 		printf("%s: PCnet version %#x not supported\n",
263 		       dev->name, chip_version);
264 		return -1;
265 	}
266 
267 	PCNET_DEBUG1("AMD %s\n", chipname);
268 
269 #ifdef PCNET_HAS_PROM
270 	/*
271 	 * In most chips, after a chip reset, the ethernet address is read from
272 	 * the station address PROM at the base address and programmed into the
273 	 * "Physical Address Registers" CSR12-14.
274 	 */
275 	for (i = 0; i < 3; i++) {
276 		unsigned int val;
277 
278 		val = pcnet_read_csr(dev, i + 12) & 0x0ffff;
279 		/* There may be endianness issues here. */
280 		dev->enetaddr[2 * i] = val & 0x0ff;
281 		dev->enetaddr[2 * i + 1] = (val >> 8) & 0x0ff;
282 	}
283 #endif /* PCNET_HAS_PROM */
284 
285 	return 0;
286 }
287 
288 static int pcnet_init(struct eth_device *dev, bd_t *bis)
289 {
290 	struct pcnet_uncached_priv *uc;
291 	int i, val;
292 	u32 addr;
293 
294 	PCNET_DEBUG1("%s: pcnet_init...\n", dev->name);
295 
296 	/* Switch pcnet to 32bit mode */
297 	pcnet_write_bcr(dev, 20, 2);
298 
299 	/* Set/reset autoselect bit */
300 	val = pcnet_read_bcr(dev, 2) & ~2;
301 	val |= 2;
302 	pcnet_write_bcr(dev, 2, val);
303 
304 	/* Enable auto negotiate, setup, disable fd */
305 	val = pcnet_read_bcr(dev, 32) & ~0x98;
306 	val |= 0x20;
307 	pcnet_write_bcr(dev, 32, val);
308 
309 	/*
310 	 * Enable NOUFLO on supported controllers, with the transmit
311 	 * start point set to the full packet. This will cause entire
312 	 * packets to be buffered by the ethernet controller before
313 	 * transmission, eliminating underflows which are common on
314 	 * slower devices. Controllers which do not support NOUFLO will
315 	 * simply be left with a larger transmit FIFO threshold.
316 	 */
317 	val = pcnet_read_bcr(dev, 18);
318 	val |= 1 << 11;
319 	pcnet_write_bcr(dev, 18, val);
320 	val = pcnet_read_csr(dev, 80);
321 	val |= 0x3 << 10;
322 	pcnet_write_csr(dev, 80, val);
323 
324 	/*
325 	 * We only maintain one structure because the drivers will never
326 	 * be used concurrently. In 32bit mode the RX and TX ring entries
327 	 * must be aligned on 16-byte boundaries.
328 	 */
329 	if (lp == NULL) {
330 		addr = (u32)malloc(sizeof(pcnet_priv_t) + 0x10);
331 		addr = (addr + 0xf) & ~0xf;
332 		lp = (pcnet_priv_t *)addr;
333 
334 		addr = (u32)memalign(ARCH_DMA_MINALIGN, sizeof(*lp->uc));
335 		flush_dcache_range(addr, addr + sizeof(*lp->uc));
336 		addr = UNCACHED_SDRAM(addr);
337 		lp->uc = (struct pcnet_uncached_priv *)addr;
338 
339 		addr = (u32)memalign(ARCH_DMA_MINALIGN, sizeof(*lp->rx_buf));
340 		flush_dcache_range(addr, addr + sizeof(*lp->rx_buf));
341 		lp->rx_buf = (void *)addr;
342 	}
343 
344 	uc = lp->uc;
345 
346 	uc->init_block.mode = cpu_to_le16(0x0000);
347 	uc->init_block.filter[0] = 0x00000000;
348 	uc->init_block.filter[1] = 0x00000000;
349 
350 	/*
351 	 * Initialize the Rx ring.
352 	 */
353 	lp->cur_rx = 0;
354 	for (i = 0; i < RX_RING_SIZE; i++) {
355 		uc->rx_ring[i].base = PCI_TO_MEM_LE(dev, (*lp->rx_buf)[i]);
356 		uc->rx_ring[i].buf_length = cpu_to_le16(-PKT_BUF_SZ);
357 		uc->rx_ring[i].status = cpu_to_le16(0x8000);
358 		PCNET_DEBUG1
359 			("Rx%d: base=0x%x buf_length=0x%hx status=0x%hx\n", i,
360 			 uc->rx_ring[i].base, uc->rx_ring[i].buf_length,
361 			 uc->rx_ring[i].status);
362 	}
363 
364 	/*
365 	 * Initialize the Tx ring. The Tx buffer address is filled in as
366 	 * needed, but we do need to clear the upper ownership bit.
367 	 */
368 	lp->cur_tx = 0;
369 	for (i = 0; i < TX_RING_SIZE; i++) {
370 		uc->tx_ring[i].base = 0;
371 		uc->tx_ring[i].status = 0;
372 	}
373 
374 	/*
375 	 * Setup Init Block.
376 	 */
377 	PCNET_DEBUG1("Init block at 0x%p: MAC", &lp->uc->init_block);
378 
379 	for (i = 0; i < 6; i++) {
380 		lp->uc->init_block.phys_addr[i] = dev->enetaddr[i];
381 		PCNET_DEBUG1(" %02x", lp->uc->init_block.phys_addr[i]);
382 	}
383 
384 	uc->init_block.tlen_rlen = cpu_to_le16(TX_RING_LEN_BITS |
385 					       RX_RING_LEN_BITS);
386 	uc->init_block.rx_ring = PCI_TO_MEM_LE(dev, uc->rx_ring);
387 	uc->init_block.tx_ring = PCI_TO_MEM_LE(dev, uc->tx_ring);
388 
389 	PCNET_DEBUG1("\ntlen_rlen=0x%x rx_ring=0x%x tx_ring=0x%x\n",
390 		     uc->init_block.tlen_rlen,
391 		     uc->init_block.rx_ring, uc->init_block.tx_ring);
392 
393 	/*
394 	 * Tell the controller where the Init Block is located.
395 	 */
396 	barrier();
397 	addr = PCI_TO_MEM(dev, &lp->uc->init_block);
398 	pcnet_write_csr(dev, 1, addr & 0xffff);
399 	pcnet_write_csr(dev, 2, (addr >> 16) & 0xffff);
400 
401 	pcnet_write_csr(dev, 4, 0x0915);
402 	pcnet_write_csr(dev, 0, 0x0001);	/* start */
403 
404 	/* Wait for Init Done bit */
405 	for (i = 10000; i > 0; i--) {
406 		if (pcnet_read_csr(dev, 0) & 0x0100)
407 			break;
408 		udelay(10);
409 	}
410 	if (i <= 0) {
411 		printf("%s: TIMEOUT: controller init failed\n", dev->name);
412 		pcnet_reset(dev);
413 		return -1;
414 	}
415 
416 	/*
417 	 * Finally start network controller operation.
418 	 */
419 	pcnet_write_csr(dev, 0, 0x0002);
420 
421 	return 0;
422 }
423 
424 static int pcnet_send(struct eth_device *dev, void *packet, int pkt_len)
425 {
426 	int i, status;
427 	struct pcnet_tx_head *entry = &lp->uc->tx_ring[lp->cur_tx];
428 
429 	PCNET_DEBUG2("Tx%d: %d bytes from 0x%p ", lp->cur_tx, pkt_len,
430 		     packet);
431 
432 	flush_dcache_range((unsigned long)packet,
433 			   (unsigned long)packet + pkt_len);
434 
435 	/* Wait for completion by testing the OWN bit */
436 	for (i = 1000; i > 0; i--) {
437 		status = readw(&entry->status);
438 		if ((status & 0x8000) == 0)
439 			break;
440 		udelay(100);
441 		PCNET_DEBUG2(".");
442 	}
443 	if (i <= 0) {
444 		printf("%s: TIMEOUT: Tx%d failed (status = 0x%x)\n",
445 		       dev->name, lp->cur_tx, status);
446 		pkt_len = 0;
447 		goto failure;
448 	}
449 
450 	/*
451 	 * Setup Tx ring. Caution: the write order is important here,
452 	 * set the status with the "ownership" bits last.
453 	 */
454 	writew(-pkt_len, &entry->length);
455 	writel(0, &entry->misc);
456 	writel(PCI_TO_MEM(dev, packet), &entry->base);
457 	writew(0x8300, &entry->status);
458 
459 	/* Trigger an immediate send poll. */
460 	pcnet_write_csr(dev, 0, 0x0008);
461 
462       failure:
463 	if (++lp->cur_tx >= TX_RING_SIZE)
464 		lp->cur_tx = 0;
465 
466 	PCNET_DEBUG2("done\n");
467 	return pkt_len;
468 }
469 
470 static int pcnet_recv (struct eth_device *dev)
471 {
472 	struct pcnet_rx_head *entry;
473 	unsigned char *buf;
474 	int pkt_len = 0;
475 	u16 status, err_status;
476 
477 	while (1) {
478 		entry = &lp->uc->rx_ring[lp->cur_rx];
479 		/*
480 		 * If we own the next entry, it's a new packet. Send it up.
481 		 */
482 		status = readw(&entry->status);
483 		if ((status & 0x8000) != 0)
484 			break;
485 		err_status = status >> 8;
486 
487 		if (err_status != 0x03) {	/* There was an error. */
488 			printf("%s: Rx%d", dev->name, lp->cur_rx);
489 			PCNET_DEBUG1(" (status=0x%x)", err_status);
490 			if (err_status & 0x20)
491 				printf(" Frame");
492 			if (err_status & 0x10)
493 				printf(" Overflow");
494 			if (err_status & 0x08)
495 				printf(" CRC");
496 			if (err_status & 0x04)
497 				printf(" Fifo");
498 			printf(" Error\n");
499 			status &= 0x03ff;
500 
501 		} else {
502 			pkt_len = (readl(&entry->msg_length) & 0xfff) - 4;
503 			if (pkt_len < 60) {
504 				printf("%s: Rx%d: invalid packet length %d\n",
505 				       dev->name, lp->cur_rx, pkt_len);
506 			} else {
507 				buf = (*lp->rx_buf)[lp->cur_rx];
508 				invalidate_dcache_range((unsigned long)buf,
509 					(unsigned long)buf + pkt_len);
510 				NetReceive(buf, pkt_len);
511 				PCNET_DEBUG2("Rx%d: %d bytes from 0x%p\n",
512 					     lp->cur_rx, pkt_len, buf);
513 			}
514 		}
515 
516 		status |= 0x8000;
517 		writew(status, &entry->status);
518 
519 		if (++lp->cur_rx >= RX_RING_SIZE)
520 			lp->cur_rx = 0;
521 	}
522 	return pkt_len;
523 }
524 
525 static void pcnet_halt(struct eth_device *dev)
526 {
527 	int i;
528 
529 	PCNET_DEBUG1("%s: pcnet_halt...\n", dev->name);
530 
531 	/* Reset the PCnet controller */
532 	pcnet_reset(dev);
533 
534 	/* Wait for Stop bit */
535 	for (i = 1000; i > 0; i--) {
536 		if (pcnet_read_csr(dev, 0) & 0x4)
537 			break;
538 		udelay(10);
539 	}
540 	if (i <= 0)
541 		printf("%s: TIMEOUT: controller reset failed\n", dev->name);
542 }
543