1 /* 2 natsemi.c: A U-Boot driver for the NatSemi DP8381x series. 3 Author: Mark A. Rakes (mark_rakes@vivato.net) 4 5 Adapted from an Etherboot driver written by: 6 7 Copyright (C) 2001 Entity Cyber, Inc. 8 9 This development of this Etherboot driver was funded by 10 11 Sicom Systems: http://www.sicompos.com/ 12 13 Author: Marty Connor (mdc@thinguin.org) 14 Adapted from a Linux driver which was written by Donald Becker 15 16 This software may be used and distributed according to the terms 17 of the GNU Public License (GPL), incorporated herein by reference. 18 19 Original Copyright Notice: 20 21 Written/copyright 1999-2001 by Donald Becker. 22 23 This software may be used and distributed according to the terms of 24 the GNU General Public License (GPL), incorporated herein by reference. 25 Drivers based on or derived from this code fall under the GPL and must 26 retain the authorship, copyright and license notice. This file is not 27 a complete program and may only be used when the entire operating 28 system is licensed under the GPL. License for under other terms may be 29 available. Contact the original author for details. 30 31 The original author may be reached as becker@scyld.com, or at 32 Scyld Computing Corporation 33 410 Severn Ave., Suite 210 34 Annapolis MD 21403 35 36 Support information and updates available at 37 http://www.scyld.com/network/netsemi.html 38 39 References: 40 http://www.scyld.com/expert/100mbps.html 41 http://www.scyld.com/expert/NWay.html 42 Datasheet is available from: 43 http://www.national.com/pf/DP/DP83815.html 44 */ 45 46 /* Revision History 47 * October 2002 mar 1.0 48 * Initial U-Boot Release. Tested with Netgear FA311 board 49 * and dp83815 chipset on custom board 50 */ 51 52 /* Includes */ 53 #include <common.h> 54 #include <malloc.h> 55 #include <net.h> 56 #include <netdev.h> 57 #include <asm/io.h> 58 #include <pci.h> 59 60 /* defines */ 61 #define EEPROM_SIZE 0xb /*12 16-bit chunks, or 24 bytes*/ 62 63 #define DSIZE 0x00000FFF 64 #define ETH_ALEN 6 65 #define CRC_SIZE 4 66 #define TOUT_LOOP 500000 67 #define TX_BUF_SIZE 1536 68 #define RX_BUF_SIZE 1536 69 #define NUM_RX_DESC 4 /* Number of Rx descriptor registers. */ 70 71 /* Offsets to the device registers. 72 Unlike software-only systems, device drivers interact with complex hardware. 73 It's not useful to define symbolic names for every register bit in the 74 device. */ 75 enum register_offsets { 76 ChipCmd = 0x00, 77 ChipConfig = 0x04, 78 EECtrl = 0x08, 79 IntrMask = 0x14, 80 IntrEnable = 0x18, 81 TxRingPtr = 0x20, 82 TxConfig = 0x24, 83 RxRingPtr = 0x30, 84 RxConfig = 0x34, 85 ClkRun = 0x3C, 86 RxFilterAddr = 0x48, 87 RxFilterData = 0x4C, 88 SiliconRev = 0x58, 89 PCIPM = 0x44, 90 BasicControl = 0x80, 91 BasicStatus = 0x84, 92 /* These are from the spec, around page 78... on a separate table. */ 93 PGSEL = 0xCC, 94 PMDCSR = 0xE4, 95 TSTDAT = 0xFC, 96 DSPCFG = 0xF4, 97 SDCFG = 0x8C 98 }; 99 100 /* Bit in ChipCmd. */ 101 enum ChipCmdBits { 102 ChipReset = 0x100, 103 RxReset = 0x20, 104 TxReset = 0x10, 105 RxOff = 0x08, 106 RxOn = 0x04, 107 TxOff = 0x02, 108 TxOn = 0x01 109 }; 110 111 enum ChipConfigBits { 112 LinkSts = 0x80000000, 113 HundSpeed = 0x40000000, 114 FullDuplex = 0x20000000, 115 TenPolarity = 0x10000000, 116 AnegDone = 0x08000000, 117 AnegEnBothBoth = 0x0000E000, 118 AnegDis100Full = 0x0000C000, 119 AnegEn100Both = 0x0000A000, 120 AnegDis100Half = 0x00008000, 121 AnegEnBothHalf = 0x00006000, 122 AnegDis10Full = 0x00004000, 123 AnegEn10Both = 0x00002000, 124 DuplexMask = 0x00008000, 125 SpeedMask = 0x00004000, 126 AnegMask = 0x00002000, 127 AnegDis10Half = 0x00000000, 128 ExtPhy = 0x00001000, 129 PhyRst = 0x00000400, 130 PhyDis = 0x00000200, 131 BootRomDisable = 0x00000004, 132 BEMode = 0x00000001, 133 }; 134 135 enum TxConfig_bits { 136 TxDrthMask = 0x3f, 137 TxFlthMask = 0x3f00, 138 TxMxdmaMask = 0x700000, 139 TxMxdma_512 = 0x0, 140 TxMxdma_4 = 0x100000, 141 TxMxdma_8 = 0x200000, 142 TxMxdma_16 = 0x300000, 143 TxMxdma_32 = 0x400000, 144 TxMxdma_64 = 0x500000, 145 TxMxdma_128 = 0x600000, 146 TxMxdma_256 = 0x700000, 147 TxCollRetry = 0x800000, 148 TxAutoPad = 0x10000000, 149 TxMacLoop = 0x20000000, 150 TxHeartIgn = 0x40000000, 151 TxCarrierIgn = 0x80000000 152 }; 153 154 enum RxConfig_bits { 155 RxDrthMask = 0x3e, 156 RxMxdmaMask = 0x700000, 157 RxMxdma_512 = 0x0, 158 RxMxdma_4 = 0x100000, 159 RxMxdma_8 = 0x200000, 160 RxMxdma_16 = 0x300000, 161 RxMxdma_32 = 0x400000, 162 RxMxdma_64 = 0x500000, 163 RxMxdma_128 = 0x600000, 164 RxMxdma_256 = 0x700000, 165 RxAcceptLong = 0x8000000, 166 RxAcceptTx = 0x10000000, 167 RxAcceptRunt = 0x40000000, 168 RxAcceptErr = 0x80000000 169 }; 170 171 /* Bits in the RxMode register. */ 172 enum rx_mode_bits { 173 AcceptErr = 0x20, 174 AcceptRunt = 0x10, 175 AcceptBroadcast = 0xC0000000, 176 AcceptMulticast = 0x00200000, 177 AcceptAllMulticast = 0x20000000, 178 AcceptAllPhys = 0x10000000, 179 AcceptMyPhys = 0x08000000 180 }; 181 182 typedef struct _BufferDesc { 183 u32 link; 184 vu_long cmdsts; 185 u32 bufptr; 186 u32 software_use; 187 } BufferDesc; 188 189 /* Bits in network_desc.status */ 190 enum desc_status_bits { 191 DescOwn = 0x80000000, DescMore = 0x40000000, DescIntr = 0x20000000, 192 DescNoCRC = 0x10000000, DescPktOK = 0x08000000, 193 DescSizeMask = 0xfff, 194 195 DescTxAbort = 0x04000000, DescTxFIFO = 0x02000000, 196 DescTxCarrier = 0x01000000, DescTxDefer = 0x00800000, 197 DescTxExcDefer = 0x00400000, DescTxOOWCol = 0x00200000, 198 DescTxExcColl = 0x00100000, DescTxCollCount = 0x000f0000, 199 200 DescRxAbort = 0x04000000, DescRxOver = 0x02000000, 201 DescRxDest = 0x01800000, DescRxLong = 0x00400000, 202 DescRxRunt = 0x00200000, DescRxInvalid = 0x00100000, 203 DescRxCRC = 0x00080000, DescRxAlign = 0x00040000, 204 DescRxLoop = 0x00020000, DesRxColl = 0x00010000, 205 }; 206 207 /* Globals */ 208 #ifdef NATSEMI_DEBUG 209 static int natsemi_debug = 0; /* 1 verbose debugging, 0 normal */ 210 #endif 211 static u32 SavedClkRun; 212 static unsigned int cur_rx; 213 static unsigned int advertising; 214 static unsigned int rx_config; 215 static unsigned int tx_config; 216 217 /* Note: transmit and receive buffers and descriptors must be 218 longword aligned */ 219 static BufferDesc txd __attribute__ ((aligned(4))); 220 static BufferDesc rxd[NUM_RX_DESC] __attribute__ ((aligned(4))); 221 222 static unsigned char txb[TX_BUF_SIZE] __attribute__ ((aligned(4))); 223 static unsigned char rxb[NUM_RX_DESC * RX_BUF_SIZE] 224 __attribute__ ((aligned(4))); 225 226 /* Function Prototypes */ 227 #if 0 228 static void write_eeprom(struct eth_device *dev, long addr, int location, 229 short value); 230 #endif 231 static int read_eeprom(struct eth_device *dev, long addr, int location); 232 static int mdio_read(struct eth_device *dev, int phy_id, int location); 233 static int natsemi_init(struct eth_device *dev, bd_t * bis); 234 static void natsemi_reset(struct eth_device *dev); 235 static void natsemi_init_rxfilter(struct eth_device *dev); 236 static void natsemi_init_txd(struct eth_device *dev); 237 static void natsemi_init_rxd(struct eth_device *dev); 238 static void natsemi_set_rx_mode(struct eth_device *dev); 239 static void natsemi_check_duplex(struct eth_device *dev); 240 static int natsemi_send(struct eth_device *dev, volatile void *packet, 241 int length); 242 static int natsemi_poll(struct eth_device *dev); 243 static void natsemi_disable(struct eth_device *dev); 244 245 static struct pci_device_id supported[] = { 246 {PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_83815}, 247 {} 248 }; 249 250 #define bus_to_phys(a) pci_mem_to_phys((pci_dev_t)dev->priv, a) 251 #define phys_to_bus(a) pci_phys_to_mem((pci_dev_t)dev->priv, a) 252 253 static inline int 254 INW(struct eth_device *dev, u_long addr) 255 { 256 return le16_to_cpu(*(vu_short *) (addr + dev->iobase)); 257 } 258 259 static int 260 INL(struct eth_device *dev, u_long addr) 261 { 262 return le32_to_cpu(*(vu_long *) (addr + dev->iobase)); 263 } 264 265 static inline void 266 OUTW(struct eth_device *dev, int command, u_long addr) 267 { 268 *(vu_short *) ((addr + dev->iobase)) = cpu_to_le16(command); 269 } 270 271 static inline void 272 OUTL(struct eth_device *dev, int command, u_long addr) 273 { 274 *(vu_long *) ((addr + dev->iobase)) = cpu_to_le32(command); 275 } 276 277 /* 278 * Function: natsemi_initialize 279 * 280 * Description: Retrieves the MAC address of the card, and sets up some 281 * globals required by other routines, and initializes the NIC, making it 282 * ready to send and receive packets. 283 * 284 * Side effects: 285 * leaves the natsemi initialized, and ready to recieve packets. 286 * 287 * Returns: struct eth_device *: pointer to NIC data structure 288 */ 289 290 int 291 natsemi_initialize(bd_t * bis) 292 { 293 pci_dev_t devno; 294 int card_number = 0; 295 struct eth_device *dev; 296 u32 iobase, status, chip_config; 297 int i, idx = 0; 298 int prev_eedata; 299 u32 tmp; 300 301 while (1) { 302 /* Find PCI device(s) */ 303 if ((devno = pci_find_devices(supported, idx++)) < 0) { 304 break; 305 } 306 307 pci_read_config_dword(devno, PCI_BASE_ADDRESS_0, &iobase); 308 iobase &= ~0x3; /* bit 1: unused and bit 0: I/O Space Indicator */ 309 310 pci_write_config_dword(devno, PCI_COMMAND, 311 PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER); 312 313 /* Check if I/O accesses and Bus Mastering are enabled. */ 314 pci_read_config_dword(devno, PCI_COMMAND, &status); 315 if (!(status & PCI_COMMAND_MEMORY)) { 316 printf("Error: Can not enable MEM access.\n"); 317 continue; 318 } else if (!(status & PCI_COMMAND_MASTER)) { 319 printf("Error: Can not enable Bus Mastering.\n"); 320 continue; 321 } 322 323 dev = (struct eth_device *) malloc(sizeof *dev); 324 325 sprintf(dev->name, "dp83815#%d", card_number); 326 dev->iobase = bus_to_phys(iobase); 327 #ifdef NATSEMI_DEBUG 328 printf("natsemi: NatSemi ns8381[56] @ %#x\n", dev->iobase); 329 #endif 330 dev->priv = (void *) devno; 331 dev->init = natsemi_init; 332 dev->halt = natsemi_disable; 333 dev->send = natsemi_send; 334 dev->recv = natsemi_poll; 335 336 eth_register(dev); 337 338 card_number++; 339 340 /* Set the latency timer for value. */ 341 pci_write_config_byte(devno, PCI_LATENCY_TIMER, 0x20); 342 343 udelay(10 * 1000); 344 345 /* natsemi has a non-standard PM control register 346 * in PCI config space. Some boards apparently need 347 * to be brought to D0 in this manner. */ 348 pci_read_config_dword(devno, PCIPM, &tmp); 349 if (tmp & (0x03 | 0x100)) { 350 /* D0 state, disable PME assertion */ 351 u32 newtmp = tmp & ~(0x03 | 0x100); 352 pci_write_config_dword(devno, PCIPM, newtmp); 353 } 354 355 printf("natsemi: EEPROM contents:\n"); 356 for (i = 0; i <= EEPROM_SIZE; i++) { 357 short eedata = read_eeprom(dev, EECtrl, i); 358 printf(" %04hx", eedata); 359 } 360 printf("\n"); 361 362 /* get MAC address */ 363 prev_eedata = read_eeprom(dev, EECtrl, 6); 364 for (i = 0; i < 3; i++) { 365 int eedata = read_eeprom(dev, EECtrl, i + 7); 366 dev->enetaddr[i*2] = (eedata << 1) + (prev_eedata >> 15); 367 dev->enetaddr[i*2+1] = eedata >> 7; 368 prev_eedata = eedata; 369 } 370 371 /* Reset the chip to erase any previous misconfiguration. */ 372 OUTL(dev, ChipReset, ChipCmd); 373 374 advertising = mdio_read(dev, 1, 4); 375 chip_config = INL(dev, ChipConfig); 376 #ifdef NATSEMI_DEBUG 377 printf("%s: Transceiver status %#08X advertising %#08X\n", 378 dev->name, (int) INL(dev, BasicStatus), advertising); 379 printf("%s: Transceiver default autoneg. %s 10%s %s duplex.\n", 380 dev->name, chip_config & AnegMask ? "enabled, advertise" : 381 "disabled, force", chip_config & SpeedMask ? "0" : "", 382 chip_config & DuplexMask ? "full" : "half"); 383 #endif 384 chip_config |= AnegEnBothBoth; 385 #ifdef NATSEMI_DEBUG 386 printf("%s: changed to autoneg. %s 10%s %s duplex.\n", 387 dev->name, chip_config & AnegMask ? "enabled, advertise" : 388 "disabled, force", chip_config & SpeedMask ? "0" : "", 389 chip_config & DuplexMask ? "full" : "half"); 390 #endif 391 /*write new autoneg bits, reset phy*/ 392 OUTL(dev, (chip_config | PhyRst), ChipConfig); 393 /*un-reset phy*/ 394 OUTL(dev, chip_config, ChipConfig); 395 396 /* Disable PME: 397 * The PME bit is initialized from the EEPROM contents. 398 * PCI cards probably have PME disabled, but motherboard 399 * implementations may have PME set to enable WakeOnLan. 400 * With PME set the chip will scan incoming packets but 401 * nothing will be written to memory. */ 402 SavedClkRun = INL(dev, ClkRun); 403 OUTL(dev, SavedClkRun & ~0x100, ClkRun); 404 } 405 return card_number; 406 } 407 408 /* Read the EEPROM and MII Management Data I/O (MDIO) interfaces. 409 The EEPROM code is for common 93c06/46 EEPROMs w/ 6bit addresses. */ 410 411 /* Delay between EEPROM clock transitions. 412 No extra delay is needed with 33MHz PCI, but future 66MHz 413 access may need a delay. */ 414 #define eeprom_delay(ee_addr) INL(dev, ee_addr) 415 416 enum EEPROM_Ctrl_Bits { 417 EE_ShiftClk = 0x04, 418 EE_DataIn = 0x01, 419 EE_ChipSelect = 0x08, 420 EE_DataOut = 0x02 421 }; 422 423 #define EE_Write0 (EE_ChipSelect) 424 #define EE_Write1 (EE_ChipSelect | EE_DataIn) 425 /* The EEPROM commands include the alway-set leading bit. */ 426 enum EEPROM_Cmds { 427 EE_WrEnCmd = (4 << 6), EE_WriteCmd = (5 << 6), 428 EE_ReadCmd = (6 << 6), EE_EraseCmd = (7 << 6), 429 }; 430 431 #if 0 432 static void 433 write_eeprom(struct eth_device *dev, long addr, int location, short value) 434 { 435 int i; 436 int ee_addr = (typeof(ee_addr))addr; 437 short wren_cmd = EE_WrEnCmd | 0x30; /*wren is 100 + 11XXXX*/ 438 short write_cmd = location | EE_WriteCmd; 439 440 #ifdef NATSEMI_DEBUG 441 printf("write_eeprom: %08x, %04hx, %04hx\n", 442 dev->iobase + ee_addr, write_cmd, value); 443 #endif 444 /* Shift the write enable command bits out. */ 445 for (i = 9; i >= 0; i--) { 446 short cmdval = (wren_cmd & (1 << i)) ? EE_Write1 : EE_Write0; 447 OUTL(dev, cmdval, ee_addr); 448 eeprom_delay(ee_addr); 449 OUTL(dev, cmdval | EE_ShiftClk, ee_addr); 450 eeprom_delay(ee_addr); 451 } 452 453 OUTL(dev, 0, ee_addr); /*bring chip select low*/ 454 OUTL(dev, EE_ShiftClk, ee_addr); 455 eeprom_delay(ee_addr); 456 457 /* Shift the write command bits out. */ 458 for (i = 9; i >= 0; i--) { 459 short cmdval = (write_cmd & (1 << i)) ? EE_Write1 : EE_Write0; 460 OUTL(dev, cmdval, ee_addr); 461 eeprom_delay(ee_addr); 462 OUTL(dev, cmdval | EE_ShiftClk, ee_addr); 463 eeprom_delay(ee_addr); 464 } 465 466 for (i = 0; i < 16; i++) { 467 short cmdval = (value & (1 << i)) ? EE_Write1 : EE_Write0; 468 OUTL(dev, cmdval, ee_addr); 469 eeprom_delay(ee_addr); 470 OUTL(dev, cmdval | EE_ShiftClk, ee_addr); 471 eeprom_delay(ee_addr); 472 } 473 474 OUTL(dev, 0, ee_addr); /*bring chip select low*/ 475 OUTL(dev, EE_ShiftClk, ee_addr); 476 for (i = 0; i < 200000; i++) { 477 OUTL(dev, EE_Write0, ee_addr); /*poll for done*/ 478 if (INL(dev, ee_addr) & EE_DataOut) { 479 break; /*finished*/ 480 } 481 } 482 eeprom_delay(ee_addr); 483 484 /* Terminate the EEPROM access. */ 485 OUTL(dev, EE_Write0, ee_addr); 486 OUTL(dev, 0, ee_addr); 487 return; 488 } 489 #endif 490 491 static int 492 read_eeprom(struct eth_device *dev, long addr, int location) 493 { 494 int i; 495 int retval = 0; 496 int ee_addr = (typeof(ee_addr))addr; 497 int read_cmd = location | EE_ReadCmd; 498 499 OUTL(dev, EE_Write0, ee_addr); 500 501 /* Shift the read command bits out. */ 502 for (i = 10; i >= 0; i--) { 503 short dataval = (read_cmd & (1 << i)) ? EE_Write1 : EE_Write0; 504 OUTL(dev, dataval, ee_addr); 505 eeprom_delay(ee_addr); 506 OUTL(dev, dataval | EE_ShiftClk, ee_addr); 507 eeprom_delay(ee_addr); 508 } 509 OUTL(dev, EE_ChipSelect, ee_addr); 510 eeprom_delay(ee_addr); 511 512 for (i = 0; i < 16; i++) { 513 OUTL(dev, EE_ChipSelect | EE_ShiftClk, ee_addr); 514 eeprom_delay(ee_addr); 515 retval |= (INL(dev, ee_addr) & EE_DataOut) ? 1 << i : 0; 516 OUTL(dev, EE_ChipSelect, ee_addr); 517 eeprom_delay(ee_addr); 518 } 519 520 /* Terminate the EEPROM access. */ 521 OUTL(dev, EE_Write0, ee_addr); 522 OUTL(dev, 0, ee_addr); 523 #ifdef NATSEMI_DEBUG 524 if (natsemi_debug) 525 printf("read_eeprom: %08x, %08x, retval %08x\n", 526 dev->iobase + ee_addr, read_cmd, retval); 527 #endif 528 return retval; 529 } 530 531 /* MII transceiver control section. 532 The 83815 series has an internal transceiver, and we present the 533 management registers as if they were MII connected. */ 534 535 static int 536 mdio_read(struct eth_device *dev, int phy_id, int location) 537 { 538 if (phy_id == 1 && location < 32) 539 return INL(dev, BasicControl+(location<<2))&0xffff; 540 else 541 return 0xffff; 542 } 543 544 /* Function: natsemi_init 545 * 546 * Description: resets the ethernet controller chip and configures 547 * registers and data structures required for sending and receiving packets. 548 * 549 * Arguments: struct eth_device *dev: NIC data structure 550 * 551 * returns: int. 552 */ 553 554 static int 555 natsemi_init(struct eth_device *dev, bd_t * bis) 556 { 557 558 natsemi_reset(dev); 559 560 /* Disable PME: 561 * The PME bit is initialized from the EEPROM contents. 562 * PCI cards probably have PME disabled, but motherboard 563 * implementations may have PME set to enable WakeOnLan. 564 * With PME set the chip will scan incoming packets but 565 * nothing will be written to memory. */ 566 OUTL(dev, SavedClkRun & ~0x100, ClkRun); 567 568 natsemi_init_rxfilter(dev); 569 natsemi_init_txd(dev); 570 natsemi_init_rxd(dev); 571 572 /* Configure the PCI bus bursts and FIFO thresholds. */ 573 tx_config = TxAutoPad | TxCollRetry | TxMxdma_256 | (0x1002); 574 rx_config = RxMxdma_256 | 0x20; 575 576 #ifdef NATSEMI_DEBUG 577 printf("%s: Setting TxConfig Register %#08X\n", dev->name, tx_config); 578 printf("%s: Setting RxConfig Register %#08X\n", dev->name, rx_config); 579 #endif 580 OUTL(dev, tx_config, TxConfig); 581 OUTL(dev, rx_config, RxConfig); 582 583 natsemi_check_duplex(dev); 584 natsemi_set_rx_mode(dev); 585 586 OUTL(dev, (RxOn | TxOn), ChipCmd); 587 return 1; 588 } 589 590 /* 591 * Function: natsemi_reset 592 * 593 * Description: soft resets the controller chip 594 * 595 * Arguments: struct eth_device *dev: NIC data structure 596 * 597 * Returns: void. 598 */ 599 static void 600 natsemi_reset(struct eth_device *dev) 601 { 602 OUTL(dev, ChipReset, ChipCmd); 603 604 /* On page 78 of the spec, they recommend some settings for "optimum 605 performance" to be done in sequence. These settings optimize some 606 of the 100Mbit autodetection circuitry. Also, we only want to do 607 this for rev C of the chip. */ 608 if (INL(dev, SiliconRev) == 0x302) { 609 OUTW(dev, 0x0001, PGSEL); 610 OUTW(dev, 0x189C, PMDCSR); 611 OUTW(dev, 0x0000, TSTDAT); 612 OUTW(dev, 0x5040, DSPCFG); 613 OUTW(dev, 0x008C, SDCFG); 614 } 615 /* Disable interrupts using the mask. */ 616 OUTL(dev, 0, IntrMask); 617 OUTL(dev, 0, IntrEnable); 618 } 619 620 /* Function: natsemi_init_rxfilter 621 * 622 * Description: sets receive filter address to our MAC address 623 * 624 * Arguments: struct eth_device *dev: NIC data structure 625 * 626 * returns: void. 627 */ 628 629 static void 630 natsemi_init_rxfilter(struct eth_device *dev) 631 { 632 int i; 633 634 for (i = 0; i < ETH_ALEN; i += 2) { 635 OUTL(dev, i, RxFilterAddr); 636 OUTW(dev, dev->enetaddr[i] + (dev->enetaddr[i + 1] << 8), 637 RxFilterData); 638 } 639 } 640 641 /* 642 * Function: natsemi_init_txd 643 * 644 * Description: initializes the Tx descriptor 645 * 646 * Arguments: struct eth_device *dev: NIC data structure 647 * 648 * returns: void. 649 */ 650 651 static void 652 natsemi_init_txd(struct eth_device *dev) 653 { 654 txd.link = (u32) 0; 655 txd.cmdsts = (u32) 0; 656 txd.bufptr = (u32) & txb[0]; 657 658 /* load Transmit Descriptor Register */ 659 OUTL(dev, (u32) & txd, TxRingPtr); 660 #ifdef NATSEMI_DEBUG 661 printf("natsemi_init_txd: TX descriptor reg loaded with: %#08X\n", 662 INL(dev, TxRingPtr)); 663 #endif 664 } 665 666 /* Function: natsemi_init_rxd 667 * 668 * Description: initializes the Rx descriptor ring 669 * 670 * Arguments: struct eth_device *dev: NIC data structure 671 * 672 * Returns: void. 673 */ 674 675 static void 676 natsemi_init_rxd(struct eth_device *dev) 677 { 678 int i; 679 680 cur_rx = 0; 681 682 /* init RX descriptor */ 683 for (i = 0; i < NUM_RX_DESC; i++) { 684 rxd[i].link = 685 cpu_to_le32((i + 1 < 686 NUM_RX_DESC) ? (u32) & rxd[i + 687 1] : (u32) & 688 rxd[0]); 689 rxd[i].cmdsts = cpu_to_le32((u32) RX_BUF_SIZE); 690 rxd[i].bufptr = cpu_to_le32((u32) & rxb[i * RX_BUF_SIZE]); 691 #ifdef NATSEMI_DEBUG 692 printf 693 ("natsemi_init_rxd: rxd[%d]=%p link=%X cmdsts=%lX bufptr=%X\n", 694 i, &rxd[i], le32_to_cpu(rxd[i].link), 695 rxd[i].cmdsts, rxd[i].bufptr); 696 #endif 697 } 698 699 /* load Receive Descriptor Register */ 700 OUTL(dev, (u32) & rxd[0], RxRingPtr); 701 702 #ifdef NATSEMI_DEBUG 703 printf("natsemi_init_rxd: RX descriptor register loaded with: %X\n", 704 INL(dev, RxRingPtr)); 705 #endif 706 } 707 708 /* Function: natsemi_set_rx_mode 709 * 710 * Description: 711 * sets the receive mode to accept all broadcast packets and packets 712 * with our MAC address, and reject all multicast packets. 713 * 714 * Arguments: struct eth_device *dev: NIC data structure 715 * 716 * Returns: void. 717 */ 718 719 static void 720 natsemi_set_rx_mode(struct eth_device *dev) 721 { 722 u32 rx_mode = AcceptBroadcast | AcceptMyPhys; 723 724 OUTL(dev, rx_mode, RxFilterAddr); 725 } 726 727 static void 728 natsemi_check_duplex(struct eth_device *dev) 729 { 730 int duplex = INL(dev, ChipConfig) & FullDuplex ? 1 : 0; 731 732 #ifdef NATSEMI_DEBUG 733 printf("%s: Setting %s-duplex based on negotiated link" 734 " capability.\n", dev->name, duplex ? "full" : "half"); 735 #endif 736 if (duplex) { 737 rx_config |= RxAcceptTx; 738 tx_config |= (TxCarrierIgn | TxHeartIgn); 739 } else { 740 rx_config &= ~RxAcceptTx; 741 tx_config &= ~(TxCarrierIgn | TxHeartIgn); 742 } 743 OUTL(dev, tx_config, TxConfig); 744 OUTL(dev, rx_config, RxConfig); 745 } 746 747 /* Function: natsemi_send 748 * 749 * Description: transmits a packet and waits for completion or timeout. 750 * 751 * Returns: void. */ 752 static int 753 natsemi_send(struct eth_device *dev, volatile void *packet, int length) 754 { 755 u32 i, status = 0; 756 u32 tx_status = 0; 757 u32 *tx_ptr = &tx_status; 758 vu_long *res = (vu_long *)tx_ptr; 759 760 /* Stop the transmitter */ 761 OUTL(dev, TxOff, ChipCmd); 762 763 #ifdef NATSEMI_DEBUG 764 if (natsemi_debug) 765 printf("natsemi_send: sending %d bytes\n", (int) length); 766 #endif 767 768 /* set the transmit buffer descriptor and enable Transmit State Machine */ 769 txd.link = cpu_to_le32(0); 770 txd.bufptr = cpu_to_le32(phys_to_bus((u32) packet)); 771 txd.cmdsts = cpu_to_le32(DescOwn | length); 772 773 /* load Transmit Descriptor Register */ 774 OUTL(dev, phys_to_bus((u32) & txd), TxRingPtr); 775 #ifdef NATSEMI_DEBUG 776 if (natsemi_debug) 777 printf("natsemi_send: TX descriptor register loaded with: %#08X\n", 778 INL(dev, TxRingPtr)); 779 #endif 780 /* restart the transmitter */ 781 OUTL(dev, TxOn, ChipCmd); 782 783 for (i = 0; 784 (*res = le32_to_cpu(txd.cmdsts)) & DescOwn; 785 i++) { 786 if (i >= TOUT_LOOP) { 787 printf 788 ("%s: tx error buffer not ready: txd.cmdsts == %#X\n", 789 dev->name, tx_status); 790 goto Done; 791 } 792 } 793 794 if (!(tx_status & DescPktOK)) { 795 printf("natsemi_send: Transmit error, Tx status %X.\n", 796 tx_status); 797 goto Done; 798 } 799 800 status = 1; 801 Done: 802 return status; 803 } 804 805 /* Function: natsemi_poll 806 * 807 * Description: checks for a received packet and returns it if found. 808 * 809 * Arguments: struct eth_device *dev: NIC data structure 810 * 811 * Returns: 1 if packet was received. 812 * 0 if no packet was received. 813 * 814 * Side effects: 815 * Returns (copies) the packet to the array dev->packet. 816 * Returns the length of the packet. 817 */ 818 819 static int 820 natsemi_poll(struct eth_device *dev) 821 { 822 int retstat = 0; 823 int length = 0; 824 u32 rx_status = le32_to_cpu(rxd[cur_rx].cmdsts); 825 826 if (!(rx_status & (u32) DescOwn)) 827 return retstat; 828 #ifdef NATSEMI_DEBUG 829 if (natsemi_debug) 830 printf("natsemi_poll: got a packet: cur_rx:%d, status:%X\n", 831 cur_rx, rx_status); 832 #endif 833 length = (rx_status & DSIZE) - CRC_SIZE; 834 835 if ((rx_status & (DescMore | DescPktOK | DescRxLong)) != DescPktOK) { 836 printf 837 ("natsemi_poll: Corrupted packet received, buffer status = %X\n", 838 rx_status); 839 retstat = 0; 840 } else { /* give packet to higher level routine */ 841 NetReceive((rxb + cur_rx * RX_BUF_SIZE), length); 842 retstat = 1; 843 } 844 845 /* return the descriptor and buffer to receive ring */ 846 rxd[cur_rx].cmdsts = cpu_to_le32(RX_BUF_SIZE); 847 rxd[cur_rx].bufptr = cpu_to_le32((u32) & rxb[cur_rx * RX_BUF_SIZE]); 848 849 if (++cur_rx == NUM_RX_DESC) 850 cur_rx = 0; 851 852 /* re-enable the potentially idle receive state machine */ 853 OUTL(dev, RxOn, ChipCmd); 854 855 return retstat; 856 } 857 858 /* Function: natsemi_disable 859 * 860 * Description: Turns off interrupts and stops Tx and Rx engines 861 * 862 * Arguments: struct eth_device *dev: NIC data structure 863 * 864 * Returns: void. 865 */ 866 867 static void 868 natsemi_disable(struct eth_device *dev) 869 { 870 /* Disable interrupts using the mask. */ 871 OUTL(dev, 0, IntrMask); 872 OUTL(dev, 0, IntrEnable); 873 874 /* Stop the chip's Tx and Rx processes. */ 875 OUTL(dev, RxOff | TxOff, ChipCmd); 876 877 /* Restore PME enable bit */ 878 OUTL(dev, SavedClkRun, ClkRun); 879 } 880