1 /* 2 natsemi.c: A U-Boot driver for the NatSemi DP8381x series. 3 Author: Mark A. Rakes (mark_rakes@vivato.net) 4 5 Adapted from an Etherboot driver written by: 6 7 Copyright (C) 2001 Entity Cyber, Inc. 8 9 This development of this Etherboot driver was funded by 10 11 Sicom Systems: http://www.sicompos.com/ 12 13 Author: Marty Connor (mdc@thinguin.org) 14 Adapted from a Linux driver which was written by Donald Becker 15 16 This software may be used and distributed according to the terms 17 of the GNU Public License (GPL), incorporated herein by reference. 18 19 Original Copyright Notice: 20 21 Written/copyright 1999-2001 by Donald Becker. 22 23 This software may be used and distributed according to the terms of 24 the GNU General Public License (GPL), incorporated herein by reference. 25 Drivers based on or derived from this code fall under the GPL and must 26 retain the authorship, copyright and license notice. This file is not 27 a complete program and may only be used when the entire operating 28 system is licensed under the GPL. License for under other terms may be 29 available. Contact the original author for details. 30 31 The original author may be reached as becker@scyld.com, or at 32 Scyld Computing Corporation 33 410 Severn Ave., Suite 210 34 Annapolis MD 21403 35 36 Support information and updates available at 37 http://www.scyld.com/network/netsemi.html 38 39 References: 40 http://www.scyld.com/expert/100mbps.html 41 http://www.scyld.com/expert/NWay.html 42 Datasheet is available from: 43 http://www.national.com/pf/DP/DP83815.html 44 */ 45 46 /* Revision History 47 * October 2002 mar 1.0 48 * Initial U-Boot Release. Tested with Netgear FA311 board 49 * and dp83815 chipset on custom board 50 */ 51 52 /* Includes */ 53 #include <common.h> 54 #include <malloc.h> 55 #include <net.h> 56 #include <netdev.h> 57 #include <asm/io.h> 58 #include <pci.h> 59 60 /* defines */ 61 #define EEPROM_SIZE 0xb /*12 16-bit chunks, or 24 bytes*/ 62 63 #define DSIZE 0x00000FFF 64 #define ETH_ALEN 6 65 #define CRC_SIZE 4 66 #define TOUT_LOOP 500000 67 #define TX_BUF_SIZE 1536 68 #define RX_BUF_SIZE 1536 69 #define NUM_RX_DESC 4 /* Number of Rx descriptor registers. */ 70 71 /* Offsets to the device registers. 72 Unlike software-only systems, device drivers interact with complex hardware. 73 It's not useful to define symbolic names for every register bit in the 74 device. */ 75 enum register_offsets { 76 ChipCmd = 0x00, 77 ChipConfig = 0x04, 78 EECtrl = 0x08, 79 IntrMask = 0x14, 80 IntrEnable = 0x18, 81 TxRingPtr = 0x20, 82 TxConfig = 0x24, 83 RxRingPtr = 0x30, 84 RxConfig = 0x34, 85 ClkRun = 0x3C, 86 RxFilterAddr = 0x48, 87 RxFilterData = 0x4C, 88 SiliconRev = 0x58, 89 PCIPM = 0x44, 90 BasicControl = 0x80, 91 BasicStatus = 0x84, 92 /* These are from the spec, around page 78... on a separate table. */ 93 PGSEL = 0xCC, 94 PMDCSR = 0xE4, 95 TSTDAT = 0xFC, 96 DSPCFG = 0xF4, 97 SDCFG = 0x8C 98 }; 99 100 /* Bit in ChipCmd. */ 101 enum ChipCmdBits { 102 ChipReset = 0x100, 103 RxReset = 0x20, 104 TxReset = 0x10, 105 RxOff = 0x08, 106 RxOn = 0x04, 107 TxOff = 0x02, 108 TxOn = 0x01 109 }; 110 111 enum ChipConfigBits { 112 LinkSts = 0x80000000, 113 HundSpeed = 0x40000000, 114 FullDuplex = 0x20000000, 115 TenPolarity = 0x10000000, 116 AnegDone = 0x08000000, 117 AnegEnBothBoth = 0x0000E000, 118 AnegDis100Full = 0x0000C000, 119 AnegEn100Both = 0x0000A000, 120 AnegDis100Half = 0x00008000, 121 AnegEnBothHalf = 0x00006000, 122 AnegDis10Full = 0x00004000, 123 AnegEn10Both = 0x00002000, 124 DuplexMask = 0x00008000, 125 SpeedMask = 0x00004000, 126 AnegMask = 0x00002000, 127 AnegDis10Half = 0x00000000, 128 ExtPhy = 0x00001000, 129 PhyRst = 0x00000400, 130 PhyDis = 0x00000200, 131 BootRomDisable = 0x00000004, 132 BEMode = 0x00000001, 133 }; 134 135 enum TxConfig_bits { 136 TxDrthMask = 0x3f, 137 TxFlthMask = 0x3f00, 138 TxMxdmaMask = 0x700000, 139 TxMxdma_512 = 0x0, 140 TxMxdma_4 = 0x100000, 141 TxMxdma_8 = 0x200000, 142 TxMxdma_16 = 0x300000, 143 TxMxdma_32 = 0x400000, 144 TxMxdma_64 = 0x500000, 145 TxMxdma_128 = 0x600000, 146 TxMxdma_256 = 0x700000, 147 TxCollRetry = 0x800000, 148 TxAutoPad = 0x10000000, 149 TxMacLoop = 0x20000000, 150 TxHeartIgn = 0x40000000, 151 TxCarrierIgn = 0x80000000 152 }; 153 154 enum RxConfig_bits { 155 RxDrthMask = 0x3e, 156 RxMxdmaMask = 0x700000, 157 RxMxdma_512 = 0x0, 158 RxMxdma_4 = 0x100000, 159 RxMxdma_8 = 0x200000, 160 RxMxdma_16 = 0x300000, 161 RxMxdma_32 = 0x400000, 162 RxMxdma_64 = 0x500000, 163 RxMxdma_128 = 0x600000, 164 RxMxdma_256 = 0x700000, 165 RxAcceptLong = 0x8000000, 166 RxAcceptTx = 0x10000000, 167 RxAcceptRunt = 0x40000000, 168 RxAcceptErr = 0x80000000 169 }; 170 171 /* Bits in the RxMode register. */ 172 enum rx_mode_bits { 173 AcceptErr = 0x20, 174 AcceptRunt = 0x10, 175 AcceptBroadcast = 0xC0000000, 176 AcceptMulticast = 0x00200000, 177 AcceptAllMulticast = 0x20000000, 178 AcceptAllPhys = 0x10000000, 179 AcceptMyPhys = 0x08000000 180 }; 181 182 typedef struct _BufferDesc { 183 u32 link; 184 vu_long cmdsts; 185 u32 bufptr; 186 u32 software_use; 187 } BufferDesc; 188 189 /* Bits in network_desc.status */ 190 enum desc_status_bits { 191 DescOwn = 0x80000000, DescMore = 0x40000000, DescIntr = 0x20000000, 192 DescNoCRC = 0x10000000, DescPktOK = 0x08000000, 193 DescSizeMask = 0xfff, 194 195 DescTxAbort = 0x04000000, DescTxFIFO = 0x02000000, 196 DescTxCarrier = 0x01000000, DescTxDefer = 0x00800000, 197 DescTxExcDefer = 0x00400000, DescTxOOWCol = 0x00200000, 198 DescTxExcColl = 0x00100000, DescTxCollCount = 0x000f0000, 199 200 DescRxAbort = 0x04000000, DescRxOver = 0x02000000, 201 DescRxDest = 0x01800000, DescRxLong = 0x00400000, 202 DescRxRunt = 0x00200000, DescRxInvalid = 0x00100000, 203 DescRxCRC = 0x00080000, DescRxAlign = 0x00040000, 204 DescRxLoop = 0x00020000, DesRxColl = 0x00010000, 205 }; 206 207 /* Globals */ 208 #ifdef NATSEMI_DEBUG 209 static int natsemi_debug = 0; /* 1 verbose debugging, 0 normal */ 210 #endif 211 static u32 SavedClkRun; 212 static unsigned int cur_rx; 213 static unsigned int advertising; 214 static unsigned int rx_config; 215 static unsigned int tx_config; 216 217 /* Note: transmit and receive buffers and descriptors must be 218 longword aligned */ 219 static BufferDesc txd __attribute__ ((aligned(4))); 220 static BufferDesc rxd[NUM_RX_DESC] __attribute__ ((aligned(4))); 221 222 static unsigned char txb[TX_BUF_SIZE] __attribute__ ((aligned(4))); 223 static unsigned char rxb[NUM_RX_DESC * RX_BUF_SIZE] 224 __attribute__ ((aligned(4))); 225 226 /* Function Prototypes */ 227 #if 0 228 static void write_eeprom(struct eth_device *dev, long addr, int location, 229 short value); 230 #endif 231 static int read_eeprom(struct eth_device *dev, long addr, int location); 232 static int mdio_read(struct eth_device *dev, int phy_id, int location); 233 static int natsemi_init(struct eth_device *dev, bd_t * bis); 234 static void natsemi_reset(struct eth_device *dev); 235 static void natsemi_init_rxfilter(struct eth_device *dev); 236 static void natsemi_init_txd(struct eth_device *dev); 237 static void natsemi_init_rxd(struct eth_device *dev); 238 static void natsemi_set_rx_mode(struct eth_device *dev); 239 static void natsemi_check_duplex(struct eth_device *dev); 240 static int natsemi_send(struct eth_device *dev, void *packet, int length); 241 static int natsemi_poll(struct eth_device *dev); 242 static void natsemi_disable(struct eth_device *dev); 243 244 static struct pci_device_id supported[] = { 245 {PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_83815}, 246 {} 247 }; 248 249 #define bus_to_phys(a) pci_mem_to_phys((pci_dev_t)dev->priv, a) 250 #define phys_to_bus(a) pci_phys_to_mem((pci_dev_t)dev->priv, a) 251 252 static inline int 253 INW(struct eth_device *dev, u_long addr) 254 { 255 return le16_to_cpu(*(vu_short *) (addr + dev->iobase)); 256 } 257 258 static int 259 INL(struct eth_device *dev, u_long addr) 260 { 261 return le32_to_cpu(*(vu_long *) (addr + dev->iobase)); 262 } 263 264 static inline void 265 OUTW(struct eth_device *dev, int command, u_long addr) 266 { 267 *(vu_short *) ((addr + dev->iobase)) = cpu_to_le16(command); 268 } 269 270 static inline void 271 OUTL(struct eth_device *dev, int command, u_long addr) 272 { 273 *(vu_long *) ((addr + dev->iobase)) = cpu_to_le32(command); 274 } 275 276 /* 277 * Function: natsemi_initialize 278 * 279 * Description: Retrieves the MAC address of the card, and sets up some 280 * globals required by other routines, and initializes the NIC, making it 281 * ready to send and receive packets. 282 * 283 * Side effects: 284 * leaves the natsemi initialized, and ready to receive packets. 285 * 286 * Returns: struct eth_device *: pointer to NIC data structure 287 */ 288 289 int 290 natsemi_initialize(bd_t * bis) 291 { 292 pci_dev_t devno; 293 int card_number = 0; 294 struct eth_device *dev; 295 u32 iobase, status, chip_config; 296 int i, idx = 0; 297 int prev_eedata; 298 u32 tmp; 299 300 while (1) { 301 /* Find PCI device(s) */ 302 if ((devno = pci_find_devices(supported, idx++)) < 0) { 303 break; 304 } 305 306 pci_read_config_dword(devno, PCI_BASE_ADDRESS_0, &iobase); 307 iobase &= ~0x3; /* bit 1: unused and bit 0: I/O Space Indicator */ 308 309 pci_write_config_dword(devno, PCI_COMMAND, 310 PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER); 311 312 /* Check if I/O accesses and Bus Mastering are enabled. */ 313 pci_read_config_dword(devno, PCI_COMMAND, &status); 314 if (!(status & PCI_COMMAND_MEMORY)) { 315 printf("Error: Can not enable MEM access.\n"); 316 continue; 317 } else if (!(status & PCI_COMMAND_MASTER)) { 318 printf("Error: Can not enable Bus Mastering.\n"); 319 continue; 320 } 321 322 dev = (struct eth_device *) malloc(sizeof *dev); 323 if (!dev) { 324 printf("natsemi: Can not allocate memory\n"); 325 break; 326 } 327 memset(dev, 0, sizeof(*dev)); 328 329 sprintf(dev->name, "dp83815#%d", card_number); 330 dev->iobase = bus_to_phys(iobase); 331 #ifdef NATSEMI_DEBUG 332 printf("natsemi: NatSemi ns8381[56] @ %#x\n", dev->iobase); 333 #endif 334 dev->priv = (void *) devno; 335 dev->init = natsemi_init; 336 dev->halt = natsemi_disable; 337 dev->send = natsemi_send; 338 dev->recv = natsemi_poll; 339 340 eth_register(dev); 341 342 card_number++; 343 344 /* Set the latency timer for value. */ 345 pci_write_config_byte(devno, PCI_LATENCY_TIMER, 0x20); 346 347 udelay(10 * 1000); 348 349 /* natsemi has a non-standard PM control register 350 * in PCI config space. Some boards apparently need 351 * to be brought to D0 in this manner. */ 352 pci_read_config_dword(devno, PCIPM, &tmp); 353 if (tmp & (0x03 | 0x100)) { 354 /* D0 state, disable PME assertion */ 355 u32 newtmp = tmp & ~(0x03 | 0x100); 356 pci_write_config_dword(devno, PCIPM, newtmp); 357 } 358 359 printf("natsemi: EEPROM contents:\n"); 360 for (i = 0; i <= EEPROM_SIZE; i++) { 361 short eedata = read_eeprom(dev, EECtrl, i); 362 printf(" %04hx", eedata); 363 } 364 printf("\n"); 365 366 /* get MAC address */ 367 prev_eedata = read_eeprom(dev, EECtrl, 6); 368 for (i = 0; i < 3; i++) { 369 int eedata = read_eeprom(dev, EECtrl, i + 7); 370 dev->enetaddr[i*2] = (eedata << 1) + (prev_eedata >> 15); 371 dev->enetaddr[i*2+1] = eedata >> 7; 372 prev_eedata = eedata; 373 } 374 375 /* Reset the chip to erase any previous misconfiguration. */ 376 OUTL(dev, ChipReset, ChipCmd); 377 378 advertising = mdio_read(dev, 1, 4); 379 chip_config = INL(dev, ChipConfig); 380 #ifdef NATSEMI_DEBUG 381 printf("%s: Transceiver status %#08X advertising %#08X\n", 382 dev->name, (int) INL(dev, BasicStatus), advertising); 383 printf("%s: Transceiver default autoneg. %s 10%s %s duplex.\n", 384 dev->name, chip_config & AnegMask ? "enabled, advertise" : 385 "disabled, force", chip_config & SpeedMask ? "0" : "", 386 chip_config & DuplexMask ? "full" : "half"); 387 #endif 388 chip_config |= AnegEnBothBoth; 389 #ifdef NATSEMI_DEBUG 390 printf("%s: changed to autoneg. %s 10%s %s duplex.\n", 391 dev->name, chip_config & AnegMask ? "enabled, advertise" : 392 "disabled, force", chip_config & SpeedMask ? "0" : "", 393 chip_config & DuplexMask ? "full" : "half"); 394 #endif 395 /*write new autoneg bits, reset phy*/ 396 OUTL(dev, (chip_config | PhyRst), ChipConfig); 397 /*un-reset phy*/ 398 OUTL(dev, chip_config, ChipConfig); 399 400 /* Disable PME: 401 * The PME bit is initialized from the EEPROM contents. 402 * PCI cards probably have PME disabled, but motherboard 403 * implementations may have PME set to enable WakeOnLan. 404 * With PME set the chip will scan incoming packets but 405 * nothing will be written to memory. */ 406 SavedClkRun = INL(dev, ClkRun); 407 OUTL(dev, SavedClkRun & ~0x100, ClkRun); 408 } 409 return card_number; 410 } 411 412 /* Read the EEPROM and MII Management Data I/O (MDIO) interfaces. 413 The EEPROM code is for common 93c06/46 EEPROMs w/ 6bit addresses. */ 414 415 /* Delay between EEPROM clock transitions. 416 No extra delay is needed with 33MHz PCI, but future 66MHz 417 access may need a delay. */ 418 #define eeprom_delay(ee_addr) INL(dev, ee_addr) 419 420 enum EEPROM_Ctrl_Bits { 421 EE_ShiftClk = 0x04, 422 EE_DataIn = 0x01, 423 EE_ChipSelect = 0x08, 424 EE_DataOut = 0x02 425 }; 426 427 #define EE_Write0 (EE_ChipSelect) 428 #define EE_Write1 (EE_ChipSelect | EE_DataIn) 429 /* The EEPROM commands include the alway-set leading bit. */ 430 enum EEPROM_Cmds { 431 EE_WrEnCmd = (4 << 6), EE_WriteCmd = (5 << 6), 432 EE_ReadCmd = (6 << 6), EE_EraseCmd = (7 << 6), 433 }; 434 435 #if 0 436 static void 437 write_eeprom(struct eth_device *dev, long addr, int location, short value) 438 { 439 int i; 440 int ee_addr = (typeof(ee_addr))addr; 441 short wren_cmd = EE_WrEnCmd | 0x30; /*wren is 100 + 11XXXX*/ 442 short write_cmd = location | EE_WriteCmd; 443 444 #ifdef NATSEMI_DEBUG 445 printf("write_eeprom: %08x, %04hx, %04hx\n", 446 dev->iobase + ee_addr, write_cmd, value); 447 #endif 448 /* Shift the write enable command bits out. */ 449 for (i = 9; i >= 0; i--) { 450 short cmdval = (wren_cmd & (1 << i)) ? EE_Write1 : EE_Write0; 451 OUTL(dev, cmdval, ee_addr); 452 eeprom_delay(ee_addr); 453 OUTL(dev, cmdval | EE_ShiftClk, ee_addr); 454 eeprom_delay(ee_addr); 455 } 456 457 OUTL(dev, 0, ee_addr); /*bring chip select low*/ 458 OUTL(dev, EE_ShiftClk, ee_addr); 459 eeprom_delay(ee_addr); 460 461 /* Shift the write command bits out. */ 462 for (i = 9; i >= 0; i--) { 463 short cmdval = (write_cmd & (1 << i)) ? EE_Write1 : EE_Write0; 464 OUTL(dev, cmdval, ee_addr); 465 eeprom_delay(ee_addr); 466 OUTL(dev, cmdval | EE_ShiftClk, ee_addr); 467 eeprom_delay(ee_addr); 468 } 469 470 for (i = 0; i < 16; i++) { 471 short cmdval = (value & (1 << i)) ? EE_Write1 : EE_Write0; 472 OUTL(dev, cmdval, ee_addr); 473 eeprom_delay(ee_addr); 474 OUTL(dev, cmdval | EE_ShiftClk, ee_addr); 475 eeprom_delay(ee_addr); 476 } 477 478 OUTL(dev, 0, ee_addr); /*bring chip select low*/ 479 OUTL(dev, EE_ShiftClk, ee_addr); 480 for (i = 0; i < 200000; i++) { 481 OUTL(dev, EE_Write0, ee_addr); /*poll for done*/ 482 if (INL(dev, ee_addr) & EE_DataOut) { 483 break; /*finished*/ 484 } 485 } 486 eeprom_delay(ee_addr); 487 488 /* Terminate the EEPROM access. */ 489 OUTL(dev, EE_Write0, ee_addr); 490 OUTL(dev, 0, ee_addr); 491 return; 492 } 493 #endif 494 495 static int 496 read_eeprom(struct eth_device *dev, long addr, int location) 497 { 498 int i; 499 int retval = 0; 500 int ee_addr = (typeof(ee_addr))addr; 501 int read_cmd = location | EE_ReadCmd; 502 503 OUTL(dev, EE_Write0, ee_addr); 504 505 /* Shift the read command bits out. */ 506 for (i = 10; i >= 0; i--) { 507 short dataval = (read_cmd & (1 << i)) ? EE_Write1 : EE_Write0; 508 OUTL(dev, dataval, ee_addr); 509 eeprom_delay(ee_addr); 510 OUTL(dev, dataval | EE_ShiftClk, ee_addr); 511 eeprom_delay(ee_addr); 512 } 513 OUTL(dev, EE_ChipSelect, ee_addr); 514 eeprom_delay(ee_addr); 515 516 for (i = 0; i < 16; i++) { 517 OUTL(dev, EE_ChipSelect | EE_ShiftClk, ee_addr); 518 eeprom_delay(ee_addr); 519 retval |= (INL(dev, ee_addr) & EE_DataOut) ? 1 << i : 0; 520 OUTL(dev, EE_ChipSelect, ee_addr); 521 eeprom_delay(ee_addr); 522 } 523 524 /* Terminate the EEPROM access. */ 525 OUTL(dev, EE_Write0, ee_addr); 526 OUTL(dev, 0, ee_addr); 527 #ifdef NATSEMI_DEBUG 528 if (natsemi_debug) 529 printf("read_eeprom: %08x, %08x, retval %08x\n", 530 dev->iobase + ee_addr, read_cmd, retval); 531 #endif 532 return retval; 533 } 534 535 /* MII transceiver control section. 536 The 83815 series has an internal transceiver, and we present the 537 management registers as if they were MII connected. */ 538 539 static int 540 mdio_read(struct eth_device *dev, int phy_id, int location) 541 { 542 if (phy_id == 1 && location < 32) 543 return INL(dev, BasicControl+(location<<2))&0xffff; 544 else 545 return 0xffff; 546 } 547 548 /* Function: natsemi_init 549 * 550 * Description: resets the ethernet controller chip and configures 551 * registers and data structures required for sending and receiving packets. 552 * 553 * Arguments: struct eth_device *dev: NIC data structure 554 * 555 * returns: int. 556 */ 557 558 static int 559 natsemi_init(struct eth_device *dev, bd_t * bis) 560 { 561 562 natsemi_reset(dev); 563 564 /* Disable PME: 565 * The PME bit is initialized from the EEPROM contents. 566 * PCI cards probably have PME disabled, but motherboard 567 * implementations may have PME set to enable WakeOnLan. 568 * With PME set the chip will scan incoming packets but 569 * nothing will be written to memory. */ 570 OUTL(dev, SavedClkRun & ~0x100, ClkRun); 571 572 natsemi_init_rxfilter(dev); 573 natsemi_init_txd(dev); 574 natsemi_init_rxd(dev); 575 576 /* Configure the PCI bus bursts and FIFO thresholds. */ 577 tx_config = TxAutoPad | TxCollRetry | TxMxdma_256 | (0x1002); 578 rx_config = RxMxdma_256 | 0x20; 579 580 #ifdef NATSEMI_DEBUG 581 printf("%s: Setting TxConfig Register %#08X\n", dev->name, tx_config); 582 printf("%s: Setting RxConfig Register %#08X\n", dev->name, rx_config); 583 #endif 584 OUTL(dev, tx_config, TxConfig); 585 OUTL(dev, rx_config, RxConfig); 586 587 natsemi_check_duplex(dev); 588 natsemi_set_rx_mode(dev); 589 590 OUTL(dev, (RxOn | TxOn), ChipCmd); 591 return 1; 592 } 593 594 /* 595 * Function: natsemi_reset 596 * 597 * Description: soft resets the controller chip 598 * 599 * Arguments: struct eth_device *dev: NIC data structure 600 * 601 * Returns: void. 602 */ 603 static void 604 natsemi_reset(struct eth_device *dev) 605 { 606 OUTL(dev, ChipReset, ChipCmd); 607 608 /* On page 78 of the spec, they recommend some settings for "optimum 609 performance" to be done in sequence. These settings optimize some 610 of the 100Mbit autodetection circuitry. Also, we only want to do 611 this for rev C of the chip. */ 612 if (INL(dev, SiliconRev) == 0x302) { 613 OUTW(dev, 0x0001, PGSEL); 614 OUTW(dev, 0x189C, PMDCSR); 615 OUTW(dev, 0x0000, TSTDAT); 616 OUTW(dev, 0x5040, DSPCFG); 617 OUTW(dev, 0x008C, SDCFG); 618 } 619 /* Disable interrupts using the mask. */ 620 OUTL(dev, 0, IntrMask); 621 OUTL(dev, 0, IntrEnable); 622 } 623 624 /* Function: natsemi_init_rxfilter 625 * 626 * Description: sets receive filter address to our MAC address 627 * 628 * Arguments: struct eth_device *dev: NIC data structure 629 * 630 * returns: void. 631 */ 632 633 static void 634 natsemi_init_rxfilter(struct eth_device *dev) 635 { 636 int i; 637 638 for (i = 0; i < ETH_ALEN; i += 2) { 639 OUTL(dev, i, RxFilterAddr); 640 OUTW(dev, dev->enetaddr[i] + (dev->enetaddr[i + 1] << 8), 641 RxFilterData); 642 } 643 } 644 645 /* 646 * Function: natsemi_init_txd 647 * 648 * Description: initializes the Tx descriptor 649 * 650 * Arguments: struct eth_device *dev: NIC data structure 651 * 652 * returns: void. 653 */ 654 655 static void 656 natsemi_init_txd(struct eth_device *dev) 657 { 658 txd.link = (u32) 0; 659 txd.cmdsts = (u32) 0; 660 txd.bufptr = (u32) & txb[0]; 661 662 /* load Transmit Descriptor Register */ 663 OUTL(dev, (u32) & txd, TxRingPtr); 664 #ifdef NATSEMI_DEBUG 665 printf("natsemi_init_txd: TX descriptor reg loaded with: %#08X\n", 666 INL(dev, TxRingPtr)); 667 #endif 668 } 669 670 /* Function: natsemi_init_rxd 671 * 672 * Description: initializes the Rx descriptor ring 673 * 674 * Arguments: struct eth_device *dev: NIC data structure 675 * 676 * Returns: void. 677 */ 678 679 static void 680 natsemi_init_rxd(struct eth_device *dev) 681 { 682 int i; 683 684 cur_rx = 0; 685 686 /* init RX descriptor */ 687 for (i = 0; i < NUM_RX_DESC; i++) { 688 rxd[i].link = 689 cpu_to_le32((i + 1 < 690 NUM_RX_DESC) ? (u32) & rxd[i + 691 1] : (u32) & 692 rxd[0]); 693 rxd[i].cmdsts = cpu_to_le32((u32) RX_BUF_SIZE); 694 rxd[i].bufptr = cpu_to_le32((u32) & rxb[i * RX_BUF_SIZE]); 695 #ifdef NATSEMI_DEBUG 696 printf 697 ("natsemi_init_rxd: rxd[%d]=%p link=%X cmdsts=%lX bufptr=%X\n", 698 i, &rxd[i], le32_to_cpu(rxd[i].link), 699 rxd[i].cmdsts, rxd[i].bufptr); 700 #endif 701 } 702 703 /* load Receive Descriptor Register */ 704 OUTL(dev, (u32) & rxd[0], RxRingPtr); 705 706 #ifdef NATSEMI_DEBUG 707 printf("natsemi_init_rxd: RX descriptor register loaded with: %X\n", 708 INL(dev, RxRingPtr)); 709 #endif 710 } 711 712 /* Function: natsemi_set_rx_mode 713 * 714 * Description: 715 * sets the receive mode to accept all broadcast packets and packets 716 * with our MAC address, and reject all multicast packets. 717 * 718 * Arguments: struct eth_device *dev: NIC data structure 719 * 720 * Returns: void. 721 */ 722 723 static void 724 natsemi_set_rx_mode(struct eth_device *dev) 725 { 726 u32 rx_mode = AcceptBroadcast | AcceptMyPhys; 727 728 OUTL(dev, rx_mode, RxFilterAddr); 729 } 730 731 static void 732 natsemi_check_duplex(struct eth_device *dev) 733 { 734 int duplex = INL(dev, ChipConfig) & FullDuplex ? 1 : 0; 735 736 #ifdef NATSEMI_DEBUG 737 printf("%s: Setting %s-duplex based on negotiated link" 738 " capability.\n", dev->name, duplex ? "full" : "half"); 739 #endif 740 if (duplex) { 741 rx_config |= RxAcceptTx; 742 tx_config |= (TxCarrierIgn | TxHeartIgn); 743 } else { 744 rx_config &= ~RxAcceptTx; 745 tx_config &= ~(TxCarrierIgn | TxHeartIgn); 746 } 747 OUTL(dev, tx_config, TxConfig); 748 OUTL(dev, rx_config, RxConfig); 749 } 750 751 /* Function: natsemi_send 752 * 753 * Description: transmits a packet and waits for completion or timeout. 754 * 755 * Returns: void. */ 756 static int natsemi_send(struct eth_device *dev, void *packet, int length) 757 { 758 u32 i, status = 0; 759 u32 tx_status = 0; 760 u32 *tx_ptr = &tx_status; 761 vu_long *res = (vu_long *)tx_ptr; 762 763 /* Stop the transmitter */ 764 OUTL(dev, TxOff, ChipCmd); 765 766 #ifdef NATSEMI_DEBUG 767 if (natsemi_debug) 768 printf("natsemi_send: sending %d bytes\n", (int) length); 769 #endif 770 771 /* set the transmit buffer descriptor and enable Transmit State Machine */ 772 txd.link = cpu_to_le32(0); 773 txd.bufptr = cpu_to_le32(phys_to_bus((u32) packet)); 774 txd.cmdsts = cpu_to_le32(DescOwn | length); 775 776 /* load Transmit Descriptor Register */ 777 OUTL(dev, phys_to_bus((u32) & txd), TxRingPtr); 778 #ifdef NATSEMI_DEBUG 779 if (natsemi_debug) 780 printf("natsemi_send: TX descriptor register loaded with: %#08X\n", 781 INL(dev, TxRingPtr)); 782 #endif 783 /* restart the transmitter */ 784 OUTL(dev, TxOn, ChipCmd); 785 786 for (i = 0; 787 (*res = le32_to_cpu(txd.cmdsts)) & DescOwn; 788 i++) { 789 if (i >= TOUT_LOOP) { 790 printf 791 ("%s: tx error buffer not ready: txd.cmdsts == %#X\n", 792 dev->name, tx_status); 793 goto Done; 794 } 795 } 796 797 if (!(tx_status & DescPktOK)) { 798 printf("natsemi_send: Transmit error, Tx status %X.\n", 799 tx_status); 800 goto Done; 801 } 802 803 status = 1; 804 Done: 805 return status; 806 } 807 808 /* Function: natsemi_poll 809 * 810 * Description: checks for a received packet and returns it if found. 811 * 812 * Arguments: struct eth_device *dev: NIC data structure 813 * 814 * Returns: 1 if packet was received. 815 * 0 if no packet was received. 816 * 817 * Side effects: 818 * Returns (copies) the packet to the array dev->packet. 819 * Returns the length of the packet. 820 */ 821 822 static int 823 natsemi_poll(struct eth_device *dev) 824 { 825 int retstat = 0; 826 int length = 0; 827 u32 rx_status = le32_to_cpu(rxd[cur_rx].cmdsts); 828 829 if (!(rx_status & (u32) DescOwn)) 830 return retstat; 831 #ifdef NATSEMI_DEBUG 832 if (natsemi_debug) 833 printf("natsemi_poll: got a packet: cur_rx:%d, status:%X\n", 834 cur_rx, rx_status); 835 #endif 836 length = (rx_status & DSIZE) - CRC_SIZE; 837 838 if ((rx_status & (DescMore | DescPktOK | DescRxLong)) != DescPktOK) { 839 printf 840 ("natsemi_poll: Corrupted packet received, buffer status = %X\n", 841 rx_status); 842 retstat = 0; 843 } else { /* give packet to higher level routine */ 844 net_process_received_packet((rxb + cur_rx * RX_BUF_SIZE), 845 length); 846 retstat = 1; 847 } 848 849 /* return the descriptor and buffer to receive ring */ 850 rxd[cur_rx].cmdsts = cpu_to_le32(RX_BUF_SIZE); 851 rxd[cur_rx].bufptr = cpu_to_le32((u32) & rxb[cur_rx * RX_BUF_SIZE]); 852 853 if (++cur_rx == NUM_RX_DESC) 854 cur_rx = 0; 855 856 /* re-enable the potentially idle receive state machine */ 857 OUTL(dev, RxOn, ChipCmd); 858 859 return retstat; 860 } 861 862 /* Function: natsemi_disable 863 * 864 * Description: Turns off interrupts and stops Tx and Rx engines 865 * 866 * Arguments: struct eth_device *dev: NIC data structure 867 * 868 * Returns: void. 869 */ 870 871 static void 872 natsemi_disable(struct eth_device *dev) 873 { 874 /* Disable interrupts using the mask. */ 875 OUTL(dev, 0, IntrMask); 876 OUTL(dev, 0, IntrEnable); 877 878 /* Stop the chip's Tx and Rx processes. */ 879 OUTL(dev, RxOff | TxOff, ChipCmd); 880 881 /* Restore PME enable bit */ 882 OUTL(dev, SavedClkRun, ClkRun); 883 } 884