1 /* 2 natsemi.c: A U-Boot driver for the NatSemi DP8381x series. 3 Author: Mark A. Rakes (mark_rakes@vivato.net) 4 5 Adapted from an Etherboot driver written by: 6 7 Copyright (C) 2001 Entity Cyber, Inc. 8 9 This development of this Etherboot driver was funded by 10 11 Sicom Systems: http://www.sicompos.com/ 12 13 Author: Marty Connor (mdc@thinguin.org) 14 Adapted from a Linux driver which was written by Donald Becker 15 16 This software may be used and distributed according to the terms 17 of the GNU Public License (GPL), incorporated herein by reference. 18 19 Original Copyright Notice: 20 21 Written/copyright 1999-2001 by Donald Becker. 22 23 This software may be used and distributed according to the terms of 24 the GNU General Public License (GPL), incorporated herein by reference. 25 Drivers based on or derived from this code fall under the GPL and must 26 retain the authorship, copyright and license notice. This file is not 27 a complete program and may only be used when the entire operating 28 system is licensed under the GPL. License for under other terms may be 29 available. Contact the original author for details. 30 31 The original author may be reached as becker@scyld.com, or at 32 Scyld Computing Corporation 33 410 Severn Ave., Suite 210 34 Annapolis MD 21403 35 36 Support information and updates available at 37 http://www.scyld.com/network/netsemi.html 38 39 References: 40 http://www.scyld.com/expert/100mbps.html 41 http://www.scyld.com/expert/NWay.html 42 Datasheet is available from: 43 http://www.national.com/pf/DP/DP83815.html 44 */ 45 46 /* Revision History 47 * October 2002 mar 1.0 48 * Initial U-Boot Release. Tested with Netgear FA311 board 49 * and dp83815 chipset on custom board 50 */ 51 52 /* Includes */ 53 #include <common.h> 54 #include <malloc.h> 55 #include <net.h> 56 #include <netdev.h> 57 #include <asm/io.h> 58 #include <pci.h> 59 60 /* defines */ 61 #define EEPROM_SIZE 0xb /*12 16-bit chunks, or 24 bytes*/ 62 63 #define DSIZE 0x00000FFF 64 #define ETH_ALEN 6 65 #define CRC_SIZE 4 66 #define TOUT_LOOP 500000 67 #define TX_BUF_SIZE 1536 68 #define RX_BUF_SIZE 1536 69 #define NUM_RX_DESC 4 /* Number of Rx descriptor registers. */ 70 71 /* Offsets to the device registers. 72 Unlike software-only systems, device drivers interact with complex hardware. 73 It's not useful to define symbolic names for every register bit in the 74 device. */ 75 enum register_offsets { 76 ChipCmd = 0x00, 77 ChipConfig = 0x04, 78 EECtrl = 0x08, 79 IntrMask = 0x14, 80 IntrEnable = 0x18, 81 TxRingPtr = 0x20, 82 TxConfig = 0x24, 83 RxRingPtr = 0x30, 84 RxConfig = 0x34, 85 ClkRun = 0x3C, 86 RxFilterAddr = 0x48, 87 RxFilterData = 0x4C, 88 SiliconRev = 0x58, 89 PCIPM = 0x44, 90 BasicControl = 0x80, 91 BasicStatus = 0x84, 92 /* These are from the spec, around page 78... on a separate table. */ 93 PGSEL = 0xCC, 94 PMDCSR = 0xE4, 95 TSTDAT = 0xFC, 96 DSPCFG = 0xF4, 97 SDCFG = 0x8C 98 }; 99 100 /* Bit in ChipCmd. */ 101 enum ChipCmdBits { 102 ChipReset = 0x100, 103 RxReset = 0x20, 104 TxReset = 0x10, 105 RxOff = 0x08, 106 RxOn = 0x04, 107 TxOff = 0x02, 108 TxOn = 0x01 109 }; 110 111 enum ChipConfigBits { 112 LinkSts = 0x80000000, 113 HundSpeed = 0x40000000, 114 FullDuplex = 0x20000000, 115 TenPolarity = 0x10000000, 116 AnegDone = 0x08000000, 117 AnegEnBothBoth = 0x0000E000, 118 AnegDis100Full = 0x0000C000, 119 AnegEn100Both = 0x0000A000, 120 AnegDis100Half = 0x00008000, 121 AnegEnBothHalf = 0x00006000, 122 AnegDis10Full = 0x00004000, 123 AnegEn10Both = 0x00002000, 124 DuplexMask = 0x00008000, 125 SpeedMask = 0x00004000, 126 AnegMask = 0x00002000, 127 AnegDis10Half = 0x00000000, 128 ExtPhy = 0x00001000, 129 PhyRst = 0x00000400, 130 PhyDis = 0x00000200, 131 BootRomDisable = 0x00000004, 132 BEMode = 0x00000001, 133 }; 134 135 enum TxConfig_bits { 136 TxDrthMask = 0x3f, 137 TxFlthMask = 0x3f00, 138 TxMxdmaMask = 0x700000, 139 TxMxdma_512 = 0x0, 140 TxMxdma_4 = 0x100000, 141 TxMxdma_8 = 0x200000, 142 TxMxdma_16 = 0x300000, 143 TxMxdma_32 = 0x400000, 144 TxMxdma_64 = 0x500000, 145 TxMxdma_128 = 0x600000, 146 TxMxdma_256 = 0x700000, 147 TxCollRetry = 0x800000, 148 TxAutoPad = 0x10000000, 149 TxMacLoop = 0x20000000, 150 TxHeartIgn = 0x40000000, 151 TxCarrierIgn = 0x80000000 152 }; 153 154 enum RxConfig_bits { 155 RxDrthMask = 0x3e, 156 RxMxdmaMask = 0x700000, 157 RxMxdma_512 = 0x0, 158 RxMxdma_4 = 0x100000, 159 RxMxdma_8 = 0x200000, 160 RxMxdma_16 = 0x300000, 161 RxMxdma_32 = 0x400000, 162 RxMxdma_64 = 0x500000, 163 RxMxdma_128 = 0x600000, 164 RxMxdma_256 = 0x700000, 165 RxAcceptLong = 0x8000000, 166 RxAcceptTx = 0x10000000, 167 RxAcceptRunt = 0x40000000, 168 RxAcceptErr = 0x80000000 169 }; 170 171 /* Bits in the RxMode register. */ 172 enum rx_mode_bits { 173 AcceptErr = 0x20, 174 AcceptRunt = 0x10, 175 AcceptBroadcast = 0xC0000000, 176 AcceptMulticast = 0x00200000, 177 AcceptAllMulticast = 0x20000000, 178 AcceptAllPhys = 0x10000000, 179 AcceptMyPhys = 0x08000000 180 }; 181 182 typedef struct _BufferDesc { 183 u32 link; 184 vu_long cmdsts; 185 u32 bufptr; 186 u32 software_use; 187 } BufferDesc; 188 189 /* Bits in network_desc.status */ 190 enum desc_status_bits { 191 DescOwn = 0x80000000, DescMore = 0x40000000, DescIntr = 0x20000000, 192 DescNoCRC = 0x10000000, DescPktOK = 0x08000000, 193 DescSizeMask = 0xfff, 194 195 DescTxAbort = 0x04000000, DescTxFIFO = 0x02000000, 196 DescTxCarrier = 0x01000000, DescTxDefer = 0x00800000, 197 DescTxExcDefer = 0x00400000, DescTxOOWCol = 0x00200000, 198 DescTxExcColl = 0x00100000, DescTxCollCount = 0x000f0000, 199 200 DescRxAbort = 0x04000000, DescRxOver = 0x02000000, 201 DescRxDest = 0x01800000, DescRxLong = 0x00400000, 202 DescRxRunt = 0x00200000, DescRxInvalid = 0x00100000, 203 DescRxCRC = 0x00080000, DescRxAlign = 0x00040000, 204 DescRxLoop = 0x00020000, DesRxColl = 0x00010000, 205 }; 206 207 /* Globals */ 208 #ifdef NATSEMI_DEBUG 209 static int natsemi_debug = 0; /* 1 verbose debugging, 0 normal */ 210 #endif 211 static u32 SavedClkRun; 212 static unsigned int cur_rx; 213 static unsigned int advertising; 214 static unsigned int rx_config; 215 static unsigned int tx_config; 216 217 /* Note: transmit and receive buffers and descriptors must be 218 longword aligned */ 219 static BufferDesc txd __attribute__ ((aligned(4))); 220 static BufferDesc rxd[NUM_RX_DESC] __attribute__ ((aligned(4))); 221 222 static unsigned char txb[TX_BUF_SIZE] __attribute__ ((aligned(4))); 223 static unsigned char rxb[NUM_RX_DESC * RX_BUF_SIZE] 224 __attribute__ ((aligned(4))); 225 226 /* Function Prototypes */ 227 #if 0 228 static void write_eeprom(struct eth_device *dev, long addr, int location, 229 short value); 230 #endif 231 static int read_eeprom(struct eth_device *dev, long addr, int location); 232 static int mdio_read(struct eth_device *dev, int phy_id, int location); 233 static int natsemi_init(struct eth_device *dev, bd_t * bis); 234 static void natsemi_reset(struct eth_device *dev); 235 static void natsemi_init_rxfilter(struct eth_device *dev); 236 static void natsemi_init_txd(struct eth_device *dev); 237 static void natsemi_init_rxd(struct eth_device *dev); 238 static void natsemi_set_rx_mode(struct eth_device *dev); 239 static void natsemi_check_duplex(struct eth_device *dev); 240 static int natsemi_send(struct eth_device *dev, volatile void *packet, 241 int length); 242 static int natsemi_poll(struct eth_device *dev); 243 static void natsemi_disable(struct eth_device *dev); 244 245 static struct pci_device_id supported[] = { 246 {PCI_VENDOR_ID_NS, PCI_DEVICE_ID_NS_83815}, 247 {} 248 }; 249 250 #define bus_to_phys(a) pci_mem_to_phys((pci_dev_t)dev->priv, a) 251 #define phys_to_bus(a) pci_phys_to_mem((pci_dev_t)dev->priv, a) 252 253 static inline int 254 INW(struct eth_device *dev, u_long addr) 255 { 256 return le16_to_cpu(*(vu_short *) (addr + dev->iobase)); 257 } 258 259 static int 260 INL(struct eth_device *dev, u_long addr) 261 { 262 return le32_to_cpu(*(vu_long *) (addr + dev->iobase)); 263 } 264 265 static inline void 266 OUTW(struct eth_device *dev, int command, u_long addr) 267 { 268 *(vu_short *) ((addr + dev->iobase)) = cpu_to_le16(command); 269 } 270 271 static inline void 272 OUTL(struct eth_device *dev, int command, u_long addr) 273 { 274 *(vu_long *) ((addr + dev->iobase)) = cpu_to_le32(command); 275 } 276 277 /* 278 * Function: natsemi_initialize 279 * 280 * Description: Retrieves the MAC address of the card, and sets up some 281 * globals required by other routines, and initializes the NIC, making it 282 * ready to send and receive packets. 283 * 284 * Side effects: 285 * leaves the natsemi initialized, and ready to receive packets. 286 * 287 * Returns: struct eth_device *: pointer to NIC data structure 288 */ 289 290 int 291 natsemi_initialize(bd_t * bis) 292 { 293 pci_dev_t devno; 294 int card_number = 0; 295 struct eth_device *dev; 296 u32 iobase, status, chip_config; 297 int i, idx = 0; 298 int prev_eedata; 299 u32 tmp; 300 301 while (1) { 302 /* Find PCI device(s) */ 303 if ((devno = pci_find_devices(supported, idx++)) < 0) { 304 break; 305 } 306 307 pci_read_config_dword(devno, PCI_BASE_ADDRESS_0, &iobase); 308 iobase &= ~0x3; /* bit 1: unused and bit 0: I/O Space Indicator */ 309 310 pci_write_config_dword(devno, PCI_COMMAND, 311 PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER); 312 313 /* Check if I/O accesses and Bus Mastering are enabled. */ 314 pci_read_config_dword(devno, PCI_COMMAND, &status); 315 if (!(status & PCI_COMMAND_MEMORY)) { 316 printf("Error: Can not enable MEM access.\n"); 317 continue; 318 } else if (!(status & PCI_COMMAND_MASTER)) { 319 printf("Error: Can not enable Bus Mastering.\n"); 320 continue; 321 } 322 323 dev = (struct eth_device *) malloc(sizeof *dev); 324 if (!dev) { 325 printf("natsemi: Can not allocate memory\n"); 326 break; 327 } 328 memset(dev, 0, sizeof(*dev)); 329 330 sprintf(dev->name, "dp83815#%d", card_number); 331 dev->iobase = bus_to_phys(iobase); 332 #ifdef NATSEMI_DEBUG 333 printf("natsemi: NatSemi ns8381[56] @ %#x\n", dev->iobase); 334 #endif 335 dev->priv = (void *) devno; 336 dev->init = natsemi_init; 337 dev->halt = natsemi_disable; 338 dev->send = natsemi_send; 339 dev->recv = natsemi_poll; 340 341 eth_register(dev); 342 343 card_number++; 344 345 /* Set the latency timer for value. */ 346 pci_write_config_byte(devno, PCI_LATENCY_TIMER, 0x20); 347 348 udelay(10 * 1000); 349 350 /* natsemi has a non-standard PM control register 351 * in PCI config space. Some boards apparently need 352 * to be brought to D0 in this manner. */ 353 pci_read_config_dword(devno, PCIPM, &tmp); 354 if (tmp & (0x03 | 0x100)) { 355 /* D0 state, disable PME assertion */ 356 u32 newtmp = tmp & ~(0x03 | 0x100); 357 pci_write_config_dword(devno, PCIPM, newtmp); 358 } 359 360 printf("natsemi: EEPROM contents:\n"); 361 for (i = 0; i <= EEPROM_SIZE; i++) { 362 short eedata = read_eeprom(dev, EECtrl, i); 363 printf(" %04hx", eedata); 364 } 365 printf("\n"); 366 367 /* get MAC address */ 368 prev_eedata = read_eeprom(dev, EECtrl, 6); 369 for (i = 0; i < 3; i++) { 370 int eedata = read_eeprom(dev, EECtrl, i + 7); 371 dev->enetaddr[i*2] = (eedata << 1) + (prev_eedata >> 15); 372 dev->enetaddr[i*2+1] = eedata >> 7; 373 prev_eedata = eedata; 374 } 375 376 /* Reset the chip to erase any previous misconfiguration. */ 377 OUTL(dev, ChipReset, ChipCmd); 378 379 advertising = mdio_read(dev, 1, 4); 380 chip_config = INL(dev, ChipConfig); 381 #ifdef NATSEMI_DEBUG 382 printf("%s: Transceiver status %#08X advertising %#08X\n", 383 dev->name, (int) INL(dev, BasicStatus), advertising); 384 printf("%s: Transceiver default autoneg. %s 10%s %s duplex.\n", 385 dev->name, chip_config & AnegMask ? "enabled, advertise" : 386 "disabled, force", chip_config & SpeedMask ? "0" : "", 387 chip_config & DuplexMask ? "full" : "half"); 388 #endif 389 chip_config |= AnegEnBothBoth; 390 #ifdef NATSEMI_DEBUG 391 printf("%s: changed to autoneg. %s 10%s %s duplex.\n", 392 dev->name, chip_config & AnegMask ? "enabled, advertise" : 393 "disabled, force", chip_config & SpeedMask ? "0" : "", 394 chip_config & DuplexMask ? "full" : "half"); 395 #endif 396 /*write new autoneg bits, reset phy*/ 397 OUTL(dev, (chip_config | PhyRst), ChipConfig); 398 /*un-reset phy*/ 399 OUTL(dev, chip_config, ChipConfig); 400 401 /* Disable PME: 402 * The PME bit is initialized from the EEPROM contents. 403 * PCI cards probably have PME disabled, but motherboard 404 * implementations may have PME set to enable WakeOnLan. 405 * With PME set the chip will scan incoming packets but 406 * nothing will be written to memory. */ 407 SavedClkRun = INL(dev, ClkRun); 408 OUTL(dev, SavedClkRun & ~0x100, ClkRun); 409 } 410 return card_number; 411 } 412 413 /* Read the EEPROM and MII Management Data I/O (MDIO) interfaces. 414 The EEPROM code is for common 93c06/46 EEPROMs w/ 6bit addresses. */ 415 416 /* Delay between EEPROM clock transitions. 417 No extra delay is needed with 33MHz PCI, but future 66MHz 418 access may need a delay. */ 419 #define eeprom_delay(ee_addr) INL(dev, ee_addr) 420 421 enum EEPROM_Ctrl_Bits { 422 EE_ShiftClk = 0x04, 423 EE_DataIn = 0x01, 424 EE_ChipSelect = 0x08, 425 EE_DataOut = 0x02 426 }; 427 428 #define EE_Write0 (EE_ChipSelect) 429 #define EE_Write1 (EE_ChipSelect | EE_DataIn) 430 /* The EEPROM commands include the alway-set leading bit. */ 431 enum EEPROM_Cmds { 432 EE_WrEnCmd = (4 << 6), EE_WriteCmd = (5 << 6), 433 EE_ReadCmd = (6 << 6), EE_EraseCmd = (7 << 6), 434 }; 435 436 #if 0 437 static void 438 write_eeprom(struct eth_device *dev, long addr, int location, short value) 439 { 440 int i; 441 int ee_addr = (typeof(ee_addr))addr; 442 short wren_cmd = EE_WrEnCmd | 0x30; /*wren is 100 + 11XXXX*/ 443 short write_cmd = location | EE_WriteCmd; 444 445 #ifdef NATSEMI_DEBUG 446 printf("write_eeprom: %08x, %04hx, %04hx\n", 447 dev->iobase + ee_addr, write_cmd, value); 448 #endif 449 /* Shift the write enable command bits out. */ 450 for (i = 9; i >= 0; i--) { 451 short cmdval = (wren_cmd & (1 << i)) ? EE_Write1 : EE_Write0; 452 OUTL(dev, cmdval, ee_addr); 453 eeprom_delay(ee_addr); 454 OUTL(dev, cmdval | EE_ShiftClk, ee_addr); 455 eeprom_delay(ee_addr); 456 } 457 458 OUTL(dev, 0, ee_addr); /*bring chip select low*/ 459 OUTL(dev, EE_ShiftClk, ee_addr); 460 eeprom_delay(ee_addr); 461 462 /* Shift the write command bits out. */ 463 for (i = 9; i >= 0; i--) { 464 short cmdval = (write_cmd & (1 << i)) ? EE_Write1 : EE_Write0; 465 OUTL(dev, cmdval, ee_addr); 466 eeprom_delay(ee_addr); 467 OUTL(dev, cmdval | EE_ShiftClk, ee_addr); 468 eeprom_delay(ee_addr); 469 } 470 471 for (i = 0; i < 16; i++) { 472 short cmdval = (value & (1 << i)) ? EE_Write1 : EE_Write0; 473 OUTL(dev, cmdval, ee_addr); 474 eeprom_delay(ee_addr); 475 OUTL(dev, cmdval | EE_ShiftClk, ee_addr); 476 eeprom_delay(ee_addr); 477 } 478 479 OUTL(dev, 0, ee_addr); /*bring chip select low*/ 480 OUTL(dev, EE_ShiftClk, ee_addr); 481 for (i = 0; i < 200000; i++) { 482 OUTL(dev, EE_Write0, ee_addr); /*poll for done*/ 483 if (INL(dev, ee_addr) & EE_DataOut) { 484 break; /*finished*/ 485 } 486 } 487 eeprom_delay(ee_addr); 488 489 /* Terminate the EEPROM access. */ 490 OUTL(dev, EE_Write0, ee_addr); 491 OUTL(dev, 0, ee_addr); 492 return; 493 } 494 #endif 495 496 static int 497 read_eeprom(struct eth_device *dev, long addr, int location) 498 { 499 int i; 500 int retval = 0; 501 int ee_addr = (typeof(ee_addr))addr; 502 int read_cmd = location | EE_ReadCmd; 503 504 OUTL(dev, EE_Write0, ee_addr); 505 506 /* Shift the read command bits out. */ 507 for (i = 10; i >= 0; i--) { 508 short dataval = (read_cmd & (1 << i)) ? EE_Write1 : EE_Write0; 509 OUTL(dev, dataval, ee_addr); 510 eeprom_delay(ee_addr); 511 OUTL(dev, dataval | EE_ShiftClk, ee_addr); 512 eeprom_delay(ee_addr); 513 } 514 OUTL(dev, EE_ChipSelect, ee_addr); 515 eeprom_delay(ee_addr); 516 517 for (i = 0; i < 16; i++) { 518 OUTL(dev, EE_ChipSelect | EE_ShiftClk, ee_addr); 519 eeprom_delay(ee_addr); 520 retval |= (INL(dev, ee_addr) & EE_DataOut) ? 1 << i : 0; 521 OUTL(dev, EE_ChipSelect, ee_addr); 522 eeprom_delay(ee_addr); 523 } 524 525 /* Terminate the EEPROM access. */ 526 OUTL(dev, EE_Write0, ee_addr); 527 OUTL(dev, 0, ee_addr); 528 #ifdef NATSEMI_DEBUG 529 if (natsemi_debug) 530 printf("read_eeprom: %08x, %08x, retval %08x\n", 531 dev->iobase + ee_addr, read_cmd, retval); 532 #endif 533 return retval; 534 } 535 536 /* MII transceiver control section. 537 The 83815 series has an internal transceiver, and we present the 538 management registers as if they were MII connected. */ 539 540 static int 541 mdio_read(struct eth_device *dev, int phy_id, int location) 542 { 543 if (phy_id == 1 && location < 32) 544 return INL(dev, BasicControl+(location<<2))&0xffff; 545 else 546 return 0xffff; 547 } 548 549 /* Function: natsemi_init 550 * 551 * Description: resets the ethernet controller chip and configures 552 * registers and data structures required for sending and receiving packets. 553 * 554 * Arguments: struct eth_device *dev: NIC data structure 555 * 556 * returns: int. 557 */ 558 559 static int 560 natsemi_init(struct eth_device *dev, bd_t * bis) 561 { 562 563 natsemi_reset(dev); 564 565 /* Disable PME: 566 * The PME bit is initialized from the EEPROM contents. 567 * PCI cards probably have PME disabled, but motherboard 568 * implementations may have PME set to enable WakeOnLan. 569 * With PME set the chip will scan incoming packets but 570 * nothing will be written to memory. */ 571 OUTL(dev, SavedClkRun & ~0x100, ClkRun); 572 573 natsemi_init_rxfilter(dev); 574 natsemi_init_txd(dev); 575 natsemi_init_rxd(dev); 576 577 /* Configure the PCI bus bursts and FIFO thresholds. */ 578 tx_config = TxAutoPad | TxCollRetry | TxMxdma_256 | (0x1002); 579 rx_config = RxMxdma_256 | 0x20; 580 581 #ifdef NATSEMI_DEBUG 582 printf("%s: Setting TxConfig Register %#08X\n", dev->name, tx_config); 583 printf("%s: Setting RxConfig Register %#08X\n", dev->name, rx_config); 584 #endif 585 OUTL(dev, tx_config, TxConfig); 586 OUTL(dev, rx_config, RxConfig); 587 588 natsemi_check_duplex(dev); 589 natsemi_set_rx_mode(dev); 590 591 OUTL(dev, (RxOn | TxOn), ChipCmd); 592 return 1; 593 } 594 595 /* 596 * Function: natsemi_reset 597 * 598 * Description: soft resets the controller chip 599 * 600 * Arguments: struct eth_device *dev: NIC data structure 601 * 602 * Returns: void. 603 */ 604 static void 605 natsemi_reset(struct eth_device *dev) 606 { 607 OUTL(dev, ChipReset, ChipCmd); 608 609 /* On page 78 of the spec, they recommend some settings for "optimum 610 performance" to be done in sequence. These settings optimize some 611 of the 100Mbit autodetection circuitry. Also, we only want to do 612 this for rev C of the chip. */ 613 if (INL(dev, SiliconRev) == 0x302) { 614 OUTW(dev, 0x0001, PGSEL); 615 OUTW(dev, 0x189C, PMDCSR); 616 OUTW(dev, 0x0000, TSTDAT); 617 OUTW(dev, 0x5040, DSPCFG); 618 OUTW(dev, 0x008C, SDCFG); 619 } 620 /* Disable interrupts using the mask. */ 621 OUTL(dev, 0, IntrMask); 622 OUTL(dev, 0, IntrEnable); 623 } 624 625 /* Function: natsemi_init_rxfilter 626 * 627 * Description: sets receive filter address to our MAC address 628 * 629 * Arguments: struct eth_device *dev: NIC data structure 630 * 631 * returns: void. 632 */ 633 634 static void 635 natsemi_init_rxfilter(struct eth_device *dev) 636 { 637 int i; 638 639 for (i = 0; i < ETH_ALEN; i += 2) { 640 OUTL(dev, i, RxFilterAddr); 641 OUTW(dev, dev->enetaddr[i] + (dev->enetaddr[i + 1] << 8), 642 RxFilterData); 643 } 644 } 645 646 /* 647 * Function: natsemi_init_txd 648 * 649 * Description: initializes the Tx descriptor 650 * 651 * Arguments: struct eth_device *dev: NIC data structure 652 * 653 * returns: void. 654 */ 655 656 static void 657 natsemi_init_txd(struct eth_device *dev) 658 { 659 txd.link = (u32) 0; 660 txd.cmdsts = (u32) 0; 661 txd.bufptr = (u32) & txb[0]; 662 663 /* load Transmit Descriptor Register */ 664 OUTL(dev, (u32) & txd, TxRingPtr); 665 #ifdef NATSEMI_DEBUG 666 printf("natsemi_init_txd: TX descriptor reg loaded with: %#08X\n", 667 INL(dev, TxRingPtr)); 668 #endif 669 } 670 671 /* Function: natsemi_init_rxd 672 * 673 * Description: initializes the Rx descriptor ring 674 * 675 * Arguments: struct eth_device *dev: NIC data structure 676 * 677 * Returns: void. 678 */ 679 680 static void 681 natsemi_init_rxd(struct eth_device *dev) 682 { 683 int i; 684 685 cur_rx = 0; 686 687 /* init RX descriptor */ 688 for (i = 0; i < NUM_RX_DESC; i++) { 689 rxd[i].link = 690 cpu_to_le32((i + 1 < 691 NUM_RX_DESC) ? (u32) & rxd[i + 692 1] : (u32) & 693 rxd[0]); 694 rxd[i].cmdsts = cpu_to_le32((u32) RX_BUF_SIZE); 695 rxd[i].bufptr = cpu_to_le32((u32) & rxb[i * RX_BUF_SIZE]); 696 #ifdef NATSEMI_DEBUG 697 printf 698 ("natsemi_init_rxd: rxd[%d]=%p link=%X cmdsts=%lX bufptr=%X\n", 699 i, &rxd[i], le32_to_cpu(rxd[i].link), 700 rxd[i].cmdsts, rxd[i].bufptr); 701 #endif 702 } 703 704 /* load Receive Descriptor Register */ 705 OUTL(dev, (u32) & rxd[0], RxRingPtr); 706 707 #ifdef NATSEMI_DEBUG 708 printf("natsemi_init_rxd: RX descriptor register loaded with: %X\n", 709 INL(dev, RxRingPtr)); 710 #endif 711 } 712 713 /* Function: natsemi_set_rx_mode 714 * 715 * Description: 716 * sets the receive mode to accept all broadcast packets and packets 717 * with our MAC address, and reject all multicast packets. 718 * 719 * Arguments: struct eth_device *dev: NIC data structure 720 * 721 * Returns: void. 722 */ 723 724 static void 725 natsemi_set_rx_mode(struct eth_device *dev) 726 { 727 u32 rx_mode = AcceptBroadcast | AcceptMyPhys; 728 729 OUTL(dev, rx_mode, RxFilterAddr); 730 } 731 732 static void 733 natsemi_check_duplex(struct eth_device *dev) 734 { 735 int duplex = INL(dev, ChipConfig) & FullDuplex ? 1 : 0; 736 737 #ifdef NATSEMI_DEBUG 738 printf("%s: Setting %s-duplex based on negotiated link" 739 " capability.\n", dev->name, duplex ? "full" : "half"); 740 #endif 741 if (duplex) { 742 rx_config |= RxAcceptTx; 743 tx_config |= (TxCarrierIgn | TxHeartIgn); 744 } else { 745 rx_config &= ~RxAcceptTx; 746 tx_config &= ~(TxCarrierIgn | TxHeartIgn); 747 } 748 OUTL(dev, tx_config, TxConfig); 749 OUTL(dev, rx_config, RxConfig); 750 } 751 752 /* Function: natsemi_send 753 * 754 * Description: transmits a packet and waits for completion or timeout. 755 * 756 * Returns: void. */ 757 static int 758 natsemi_send(struct eth_device *dev, volatile void *packet, int length) 759 { 760 u32 i, status = 0; 761 u32 tx_status = 0; 762 u32 *tx_ptr = &tx_status; 763 vu_long *res = (vu_long *)tx_ptr; 764 765 /* Stop the transmitter */ 766 OUTL(dev, TxOff, ChipCmd); 767 768 #ifdef NATSEMI_DEBUG 769 if (natsemi_debug) 770 printf("natsemi_send: sending %d bytes\n", (int) length); 771 #endif 772 773 /* set the transmit buffer descriptor and enable Transmit State Machine */ 774 txd.link = cpu_to_le32(0); 775 txd.bufptr = cpu_to_le32(phys_to_bus((u32) packet)); 776 txd.cmdsts = cpu_to_le32(DescOwn | length); 777 778 /* load Transmit Descriptor Register */ 779 OUTL(dev, phys_to_bus((u32) & txd), TxRingPtr); 780 #ifdef NATSEMI_DEBUG 781 if (natsemi_debug) 782 printf("natsemi_send: TX descriptor register loaded with: %#08X\n", 783 INL(dev, TxRingPtr)); 784 #endif 785 /* restart the transmitter */ 786 OUTL(dev, TxOn, ChipCmd); 787 788 for (i = 0; 789 (*res = le32_to_cpu(txd.cmdsts)) & DescOwn; 790 i++) { 791 if (i >= TOUT_LOOP) { 792 printf 793 ("%s: tx error buffer not ready: txd.cmdsts == %#X\n", 794 dev->name, tx_status); 795 goto Done; 796 } 797 } 798 799 if (!(tx_status & DescPktOK)) { 800 printf("natsemi_send: Transmit error, Tx status %X.\n", 801 tx_status); 802 goto Done; 803 } 804 805 status = 1; 806 Done: 807 return status; 808 } 809 810 /* Function: natsemi_poll 811 * 812 * Description: checks for a received packet and returns it if found. 813 * 814 * Arguments: struct eth_device *dev: NIC data structure 815 * 816 * Returns: 1 if packet was received. 817 * 0 if no packet was received. 818 * 819 * Side effects: 820 * Returns (copies) the packet to the array dev->packet. 821 * Returns the length of the packet. 822 */ 823 824 static int 825 natsemi_poll(struct eth_device *dev) 826 { 827 int retstat = 0; 828 int length = 0; 829 u32 rx_status = le32_to_cpu(rxd[cur_rx].cmdsts); 830 831 if (!(rx_status & (u32) DescOwn)) 832 return retstat; 833 #ifdef NATSEMI_DEBUG 834 if (natsemi_debug) 835 printf("natsemi_poll: got a packet: cur_rx:%d, status:%X\n", 836 cur_rx, rx_status); 837 #endif 838 length = (rx_status & DSIZE) - CRC_SIZE; 839 840 if ((rx_status & (DescMore | DescPktOK | DescRxLong)) != DescPktOK) { 841 printf 842 ("natsemi_poll: Corrupted packet received, buffer status = %X\n", 843 rx_status); 844 retstat = 0; 845 } else { /* give packet to higher level routine */ 846 NetReceive((rxb + cur_rx * RX_BUF_SIZE), length); 847 retstat = 1; 848 } 849 850 /* return the descriptor and buffer to receive ring */ 851 rxd[cur_rx].cmdsts = cpu_to_le32(RX_BUF_SIZE); 852 rxd[cur_rx].bufptr = cpu_to_le32((u32) & rxb[cur_rx * RX_BUF_SIZE]); 853 854 if (++cur_rx == NUM_RX_DESC) 855 cur_rx = 0; 856 857 /* re-enable the potentially idle receive state machine */ 858 OUTL(dev, RxOn, ChipCmd); 859 860 return retstat; 861 } 862 863 /* Function: natsemi_disable 864 * 865 * Description: Turns off interrupts and stops Tx and Rx engines 866 * 867 * Arguments: struct eth_device *dev: NIC data structure 868 * 869 * Returns: void. 870 */ 871 872 static void 873 natsemi_disable(struct eth_device *dev) 874 { 875 /* Disable interrupts using the mask. */ 876 OUTL(dev, 0, IntrMask); 877 OUTL(dev, 0, IntrEnable); 878 879 /* Stop the chip's Tx and Rx processes. */ 880 OUTL(dev, RxOff | TxOff, ChipCmd); 881 882 /* Restore PME enable bit */ 883 OUTL(dev, SavedClkRun, ClkRun); 884 } 885