1 /* 2 * Driver for Marvell NETA network card for Armada XP and Armada 370 SoCs. 3 * 4 * U-Boot version: 5 * Copyright (C) 2014-2015 Stefan Roese <sr@denx.de> 6 * 7 * Based on the Linux version which is: 8 * Copyright (C) 2012 Marvell 9 * 10 * Rami Rosen <rosenr@marvell.com> 11 * Thomas Petazzoni <thomas.petazzoni@free-electrons.com> 12 * 13 * SPDX-License-Identifier: GPL-2.0 14 */ 15 16 #include <common.h> 17 #include <dm.h> 18 #include <net.h> 19 #include <netdev.h> 20 #include <config.h> 21 #include <malloc.h> 22 #include <asm/io.h> 23 #include <linux/errno.h> 24 #include <phy.h> 25 #include <miiphy.h> 26 #include <watchdog.h> 27 #include <asm/arch/cpu.h> 28 #include <asm/arch/soc.h> 29 #include <linux/compat.h> 30 #include <linux/mbus.h> 31 32 DECLARE_GLOBAL_DATA_PTR; 33 34 #if !defined(CONFIG_PHYLIB) 35 # error Marvell mvneta requires PHYLIB 36 #endif 37 38 /* Some linux -> U-Boot compatibility stuff */ 39 #define netdev_err(dev, fmt, args...) \ 40 printf(fmt, ##args) 41 #define netdev_warn(dev, fmt, args...) \ 42 printf(fmt, ##args) 43 #define netdev_info(dev, fmt, args...) \ 44 printf(fmt, ##args) 45 46 #define CONFIG_NR_CPUS 1 47 #define ETH_HLEN 14 /* Total octets in header */ 48 49 /* 2(HW hdr) 14(MAC hdr) 4(CRC) 32(extra for cache prefetch) */ 50 #define WRAP (2 + ETH_HLEN + 4 + 32) 51 #define MTU 1500 52 #define RX_BUFFER_SIZE (ALIGN(MTU + WRAP, ARCH_DMA_MINALIGN)) 53 54 #define MVNETA_SMI_TIMEOUT 10000 55 56 /* Registers */ 57 #define MVNETA_RXQ_CONFIG_REG(q) (0x1400 + ((q) << 2)) 58 #define MVNETA_RXQ_HW_BUF_ALLOC BIT(1) 59 #define MVNETA_RXQ_PKT_OFFSET_ALL_MASK (0xf << 8) 60 #define MVNETA_RXQ_PKT_OFFSET_MASK(offs) ((offs) << 8) 61 #define MVNETA_RXQ_THRESHOLD_REG(q) (0x14c0 + ((q) << 2)) 62 #define MVNETA_RXQ_NON_OCCUPIED(v) ((v) << 16) 63 #define MVNETA_RXQ_BASE_ADDR_REG(q) (0x1480 + ((q) << 2)) 64 #define MVNETA_RXQ_SIZE_REG(q) (0x14a0 + ((q) << 2)) 65 #define MVNETA_RXQ_BUF_SIZE_SHIFT 19 66 #define MVNETA_RXQ_BUF_SIZE_MASK (0x1fff << 19) 67 #define MVNETA_RXQ_STATUS_REG(q) (0x14e0 + ((q) << 2)) 68 #define MVNETA_RXQ_OCCUPIED_ALL_MASK 0x3fff 69 #define MVNETA_RXQ_STATUS_UPDATE_REG(q) (0x1500 + ((q) << 2)) 70 #define MVNETA_RXQ_ADD_NON_OCCUPIED_SHIFT 16 71 #define MVNETA_RXQ_ADD_NON_OCCUPIED_MAX 255 72 #define MVNETA_PORT_RX_RESET 0x1cc0 73 #define MVNETA_PORT_RX_DMA_RESET BIT(0) 74 #define MVNETA_PHY_ADDR 0x2000 75 #define MVNETA_PHY_ADDR_MASK 0x1f 76 #define MVNETA_SMI 0x2004 77 #define MVNETA_PHY_REG_MASK 0x1f 78 /* SMI register fields */ 79 #define MVNETA_SMI_DATA_OFFS 0 /* Data */ 80 #define MVNETA_SMI_DATA_MASK (0xffff << MVNETA_SMI_DATA_OFFS) 81 #define MVNETA_SMI_DEV_ADDR_OFFS 16 /* PHY device address */ 82 #define MVNETA_SMI_REG_ADDR_OFFS 21 /* PHY device reg addr*/ 83 #define MVNETA_SMI_OPCODE_OFFS 26 /* Write/Read opcode */ 84 #define MVNETA_SMI_OPCODE_READ (1 << MVNETA_SMI_OPCODE_OFFS) 85 #define MVNETA_SMI_READ_VALID (1 << 27) /* Read Valid */ 86 #define MVNETA_SMI_BUSY (1 << 28) /* Busy */ 87 #define MVNETA_MBUS_RETRY 0x2010 88 #define MVNETA_UNIT_INTR_CAUSE 0x2080 89 #define MVNETA_UNIT_CONTROL 0x20B0 90 #define MVNETA_PHY_POLLING_ENABLE BIT(1) 91 #define MVNETA_WIN_BASE(w) (0x2200 + ((w) << 3)) 92 #define MVNETA_WIN_SIZE(w) (0x2204 + ((w) << 3)) 93 #define MVNETA_WIN_REMAP(w) (0x2280 + ((w) << 2)) 94 #define MVNETA_WIN_SIZE_MASK (0xffff0000) 95 #define MVNETA_BASE_ADDR_ENABLE 0x2290 96 #define MVNETA_BASE_ADDR_ENABLE_BIT 0x1 97 #define MVNETA_PORT_ACCESS_PROTECT 0x2294 98 #define MVNETA_PORT_ACCESS_PROTECT_WIN0_RW 0x3 99 #define MVNETA_PORT_CONFIG 0x2400 100 #define MVNETA_UNI_PROMISC_MODE BIT(0) 101 #define MVNETA_DEF_RXQ(q) ((q) << 1) 102 #define MVNETA_DEF_RXQ_ARP(q) ((q) << 4) 103 #define MVNETA_TX_UNSET_ERR_SUM BIT(12) 104 #define MVNETA_DEF_RXQ_TCP(q) ((q) << 16) 105 #define MVNETA_DEF_RXQ_UDP(q) ((q) << 19) 106 #define MVNETA_DEF_RXQ_BPDU(q) ((q) << 22) 107 #define MVNETA_RX_CSUM_WITH_PSEUDO_HDR BIT(25) 108 #define MVNETA_PORT_CONFIG_DEFL_VALUE(q) (MVNETA_DEF_RXQ(q) | \ 109 MVNETA_DEF_RXQ_ARP(q) | \ 110 MVNETA_DEF_RXQ_TCP(q) | \ 111 MVNETA_DEF_RXQ_UDP(q) | \ 112 MVNETA_DEF_RXQ_BPDU(q) | \ 113 MVNETA_TX_UNSET_ERR_SUM | \ 114 MVNETA_RX_CSUM_WITH_PSEUDO_HDR) 115 #define MVNETA_PORT_CONFIG_EXTEND 0x2404 116 #define MVNETA_MAC_ADDR_LOW 0x2414 117 #define MVNETA_MAC_ADDR_HIGH 0x2418 118 #define MVNETA_SDMA_CONFIG 0x241c 119 #define MVNETA_SDMA_BRST_SIZE_16 4 120 #define MVNETA_RX_BRST_SZ_MASK(burst) ((burst) << 1) 121 #define MVNETA_RX_NO_DATA_SWAP BIT(4) 122 #define MVNETA_TX_NO_DATA_SWAP BIT(5) 123 #define MVNETA_DESC_SWAP BIT(6) 124 #define MVNETA_TX_BRST_SZ_MASK(burst) ((burst) << 22) 125 #define MVNETA_PORT_STATUS 0x2444 126 #define MVNETA_TX_IN_PRGRS BIT(1) 127 #define MVNETA_TX_FIFO_EMPTY BIT(8) 128 #define MVNETA_RX_MIN_FRAME_SIZE 0x247c 129 #define MVNETA_SERDES_CFG 0x24A0 130 #define MVNETA_SGMII_SERDES_PROTO 0x0cc7 131 #define MVNETA_QSGMII_SERDES_PROTO 0x0667 132 #define MVNETA_TYPE_PRIO 0x24bc 133 #define MVNETA_FORCE_UNI BIT(21) 134 #define MVNETA_TXQ_CMD_1 0x24e4 135 #define MVNETA_TXQ_CMD 0x2448 136 #define MVNETA_TXQ_DISABLE_SHIFT 8 137 #define MVNETA_TXQ_ENABLE_MASK 0x000000ff 138 #define MVNETA_ACC_MODE 0x2500 139 #define MVNETA_CPU_MAP(cpu) (0x2540 + ((cpu) << 2)) 140 #define MVNETA_CPU_RXQ_ACCESS_ALL_MASK 0x000000ff 141 #define MVNETA_CPU_TXQ_ACCESS_ALL_MASK 0x0000ff00 142 #define MVNETA_RXQ_TIME_COAL_REG(q) (0x2580 + ((q) << 2)) 143 144 /* Exception Interrupt Port/Queue Cause register */ 145 146 #define MVNETA_INTR_NEW_CAUSE 0x25a0 147 #define MVNETA_INTR_NEW_MASK 0x25a4 148 149 /* bits 0..7 = TXQ SENT, one bit per queue. 150 * bits 8..15 = RXQ OCCUP, one bit per queue. 151 * bits 16..23 = RXQ FREE, one bit per queue. 152 * bit 29 = OLD_REG_SUM, see old reg ? 153 * bit 30 = TX_ERR_SUM, one bit for 4 ports 154 * bit 31 = MISC_SUM, one bit for 4 ports 155 */ 156 #define MVNETA_TX_INTR_MASK(nr_txqs) (((1 << nr_txqs) - 1) << 0) 157 #define MVNETA_TX_INTR_MASK_ALL (0xff << 0) 158 #define MVNETA_RX_INTR_MASK(nr_rxqs) (((1 << nr_rxqs) - 1) << 8) 159 #define MVNETA_RX_INTR_MASK_ALL (0xff << 8) 160 161 #define MVNETA_INTR_OLD_CAUSE 0x25a8 162 #define MVNETA_INTR_OLD_MASK 0x25ac 163 164 /* Data Path Port/Queue Cause Register */ 165 #define MVNETA_INTR_MISC_CAUSE 0x25b0 166 #define MVNETA_INTR_MISC_MASK 0x25b4 167 #define MVNETA_INTR_ENABLE 0x25b8 168 169 #define MVNETA_RXQ_CMD 0x2680 170 #define MVNETA_RXQ_DISABLE_SHIFT 8 171 #define MVNETA_RXQ_ENABLE_MASK 0x000000ff 172 #define MVETH_TXQ_TOKEN_COUNT_REG(q) (0x2700 + ((q) << 4)) 173 #define MVETH_TXQ_TOKEN_CFG_REG(q) (0x2704 + ((q) << 4)) 174 #define MVNETA_GMAC_CTRL_0 0x2c00 175 #define MVNETA_GMAC_MAX_RX_SIZE_SHIFT 2 176 #define MVNETA_GMAC_MAX_RX_SIZE_MASK 0x7ffc 177 #define MVNETA_GMAC0_PORT_ENABLE BIT(0) 178 #define MVNETA_GMAC_CTRL_2 0x2c08 179 #define MVNETA_GMAC2_PCS_ENABLE BIT(3) 180 #define MVNETA_GMAC2_PORT_RGMII BIT(4) 181 #define MVNETA_GMAC2_PORT_RESET BIT(6) 182 #define MVNETA_GMAC_STATUS 0x2c10 183 #define MVNETA_GMAC_LINK_UP BIT(0) 184 #define MVNETA_GMAC_SPEED_1000 BIT(1) 185 #define MVNETA_GMAC_SPEED_100 BIT(2) 186 #define MVNETA_GMAC_FULL_DUPLEX BIT(3) 187 #define MVNETA_GMAC_RX_FLOW_CTRL_ENABLE BIT(4) 188 #define MVNETA_GMAC_TX_FLOW_CTRL_ENABLE BIT(5) 189 #define MVNETA_GMAC_RX_FLOW_CTRL_ACTIVE BIT(6) 190 #define MVNETA_GMAC_TX_FLOW_CTRL_ACTIVE BIT(7) 191 #define MVNETA_GMAC_AUTONEG_CONFIG 0x2c0c 192 #define MVNETA_GMAC_FORCE_LINK_DOWN BIT(0) 193 #define MVNETA_GMAC_FORCE_LINK_PASS BIT(1) 194 #define MVNETA_GMAC_CONFIG_MII_SPEED BIT(5) 195 #define MVNETA_GMAC_CONFIG_GMII_SPEED BIT(6) 196 #define MVNETA_GMAC_AN_SPEED_EN BIT(7) 197 #define MVNETA_GMAC_CONFIG_FULL_DUPLEX BIT(12) 198 #define MVNETA_GMAC_AN_DUPLEX_EN BIT(13) 199 #define MVNETA_MIB_COUNTERS_BASE 0x3080 200 #define MVNETA_MIB_LATE_COLLISION 0x7c 201 #define MVNETA_DA_FILT_SPEC_MCAST 0x3400 202 #define MVNETA_DA_FILT_OTH_MCAST 0x3500 203 #define MVNETA_DA_FILT_UCAST_BASE 0x3600 204 #define MVNETA_TXQ_BASE_ADDR_REG(q) (0x3c00 + ((q) << 2)) 205 #define MVNETA_TXQ_SIZE_REG(q) (0x3c20 + ((q) << 2)) 206 #define MVNETA_TXQ_SENT_THRESH_ALL_MASK 0x3fff0000 207 #define MVNETA_TXQ_SENT_THRESH_MASK(coal) ((coal) << 16) 208 #define MVNETA_TXQ_UPDATE_REG(q) (0x3c60 + ((q) << 2)) 209 #define MVNETA_TXQ_DEC_SENT_SHIFT 16 210 #define MVNETA_TXQ_STATUS_REG(q) (0x3c40 + ((q) << 2)) 211 #define MVNETA_TXQ_SENT_DESC_SHIFT 16 212 #define MVNETA_TXQ_SENT_DESC_MASK 0x3fff0000 213 #define MVNETA_PORT_TX_RESET 0x3cf0 214 #define MVNETA_PORT_TX_DMA_RESET BIT(0) 215 #define MVNETA_TX_MTU 0x3e0c 216 #define MVNETA_TX_TOKEN_SIZE 0x3e14 217 #define MVNETA_TX_TOKEN_SIZE_MAX 0xffffffff 218 #define MVNETA_TXQ_TOKEN_SIZE_REG(q) (0x3e40 + ((q) << 2)) 219 #define MVNETA_TXQ_TOKEN_SIZE_MAX 0x7fffffff 220 221 /* Descriptor ring Macros */ 222 #define MVNETA_QUEUE_NEXT_DESC(q, index) \ 223 (((index) < (q)->last_desc) ? ((index) + 1) : 0) 224 225 /* Various constants */ 226 227 /* Coalescing */ 228 #define MVNETA_TXDONE_COAL_PKTS 16 229 #define MVNETA_RX_COAL_PKTS 32 230 #define MVNETA_RX_COAL_USEC 100 231 232 /* The two bytes Marvell header. Either contains a special value used 233 * by Marvell switches when a specific hardware mode is enabled (not 234 * supported by this driver) or is filled automatically by zeroes on 235 * the RX side. Those two bytes being at the front of the Ethernet 236 * header, they allow to have the IP header aligned on a 4 bytes 237 * boundary automatically: the hardware skips those two bytes on its 238 * own. 239 */ 240 #define MVNETA_MH_SIZE 2 241 242 #define MVNETA_VLAN_TAG_LEN 4 243 244 #define MVNETA_CPU_D_CACHE_LINE_SIZE 32 245 #define MVNETA_TX_CSUM_MAX_SIZE 9800 246 #define MVNETA_ACC_MODE_EXT 1 247 248 /* Timeout constants */ 249 #define MVNETA_TX_DISABLE_TIMEOUT_MSEC 1000 250 #define MVNETA_RX_DISABLE_TIMEOUT_MSEC 1000 251 #define MVNETA_TX_FIFO_EMPTY_TIMEOUT 10000 252 253 #define MVNETA_TX_MTU_MAX 0x3ffff 254 255 /* Max number of Rx descriptors */ 256 #define MVNETA_MAX_RXD 16 257 258 /* Max number of Tx descriptors */ 259 #define MVNETA_MAX_TXD 16 260 261 /* descriptor aligned size */ 262 #define MVNETA_DESC_ALIGNED_SIZE 32 263 264 struct mvneta_port { 265 void __iomem *base; 266 struct mvneta_rx_queue *rxqs; 267 struct mvneta_tx_queue *txqs; 268 269 u8 mcast_count[256]; 270 u16 tx_ring_size; 271 u16 rx_ring_size; 272 273 phy_interface_t phy_interface; 274 unsigned int link; 275 unsigned int duplex; 276 unsigned int speed; 277 278 int init; 279 int phyaddr; 280 struct phy_device *phydev; 281 struct mii_dev *bus; 282 }; 283 284 /* The mvneta_tx_desc and mvneta_rx_desc structures describe the 285 * layout of the transmit and reception DMA descriptors, and their 286 * layout is therefore defined by the hardware design 287 */ 288 289 #define MVNETA_TX_L3_OFF_SHIFT 0 290 #define MVNETA_TX_IP_HLEN_SHIFT 8 291 #define MVNETA_TX_L4_UDP BIT(16) 292 #define MVNETA_TX_L3_IP6 BIT(17) 293 #define MVNETA_TXD_IP_CSUM BIT(18) 294 #define MVNETA_TXD_Z_PAD BIT(19) 295 #define MVNETA_TXD_L_DESC BIT(20) 296 #define MVNETA_TXD_F_DESC BIT(21) 297 #define MVNETA_TXD_FLZ_DESC (MVNETA_TXD_Z_PAD | \ 298 MVNETA_TXD_L_DESC | \ 299 MVNETA_TXD_F_DESC) 300 #define MVNETA_TX_L4_CSUM_FULL BIT(30) 301 #define MVNETA_TX_L4_CSUM_NOT BIT(31) 302 303 #define MVNETA_RXD_ERR_CRC 0x0 304 #define MVNETA_RXD_ERR_SUMMARY BIT(16) 305 #define MVNETA_RXD_ERR_OVERRUN BIT(17) 306 #define MVNETA_RXD_ERR_LEN BIT(18) 307 #define MVNETA_RXD_ERR_RESOURCE (BIT(17) | BIT(18)) 308 #define MVNETA_RXD_ERR_CODE_MASK (BIT(17) | BIT(18)) 309 #define MVNETA_RXD_L3_IP4 BIT(25) 310 #define MVNETA_RXD_FIRST_LAST_DESC (BIT(26) | BIT(27)) 311 #define MVNETA_RXD_L4_CSUM_OK BIT(30) 312 313 struct mvneta_tx_desc { 314 u32 command; /* Options used by HW for packet transmitting.*/ 315 u16 reserverd1; /* csum_l4 (for future use) */ 316 u16 data_size; /* Data size of transmitted packet in bytes */ 317 u32 buf_phys_addr; /* Physical addr of transmitted buffer */ 318 u32 reserved2; /* hw_cmd - (for future use, PMT) */ 319 u32 reserved3[4]; /* Reserved - (for future use) */ 320 }; 321 322 struct mvneta_rx_desc { 323 u32 status; /* Info about received packet */ 324 u16 reserved1; /* pnc_info - (for future use, PnC) */ 325 u16 data_size; /* Size of received packet in bytes */ 326 327 u32 buf_phys_addr; /* Physical address of the buffer */ 328 u32 reserved2; /* pnc_flow_id (for future use, PnC) */ 329 330 u32 buf_cookie; /* cookie for access to RX buffer in rx path */ 331 u16 reserved3; /* prefetch_cmd, for future use */ 332 u16 reserved4; /* csum_l4 - (for future use, PnC) */ 333 334 u32 reserved5; /* pnc_extra PnC (for future use, PnC) */ 335 u32 reserved6; /* hw_cmd (for future use, PnC and HWF) */ 336 }; 337 338 struct mvneta_tx_queue { 339 /* Number of this TX queue, in the range 0-7 */ 340 u8 id; 341 342 /* Number of TX DMA descriptors in the descriptor ring */ 343 int size; 344 345 /* Index of last TX DMA descriptor that was inserted */ 346 int txq_put_index; 347 348 /* Index of the TX DMA descriptor to be cleaned up */ 349 int txq_get_index; 350 351 /* Virtual address of the TX DMA descriptors array */ 352 struct mvneta_tx_desc *descs; 353 354 /* DMA address of the TX DMA descriptors array */ 355 dma_addr_t descs_phys; 356 357 /* Index of the last TX DMA descriptor */ 358 int last_desc; 359 360 /* Index of the next TX DMA descriptor to process */ 361 int next_desc_to_proc; 362 }; 363 364 struct mvneta_rx_queue { 365 /* rx queue number, in the range 0-7 */ 366 u8 id; 367 368 /* num of rx descriptors in the rx descriptor ring */ 369 int size; 370 371 /* Virtual address of the RX DMA descriptors array */ 372 struct mvneta_rx_desc *descs; 373 374 /* DMA address of the RX DMA descriptors array */ 375 dma_addr_t descs_phys; 376 377 /* Index of the last RX DMA descriptor */ 378 int last_desc; 379 380 /* Index of the next RX DMA descriptor to process */ 381 int next_desc_to_proc; 382 }; 383 384 /* U-Boot doesn't use the queues, so set the number to 1 */ 385 static int rxq_number = 1; 386 static int txq_number = 1; 387 static int rxq_def; 388 389 struct buffer_location { 390 struct mvneta_tx_desc *tx_descs; 391 struct mvneta_rx_desc *rx_descs; 392 u32 rx_buffers; 393 }; 394 395 /* 396 * All 4 interfaces use the same global buffer, since only one interface 397 * can be enabled at once 398 */ 399 static struct buffer_location buffer_loc; 400 401 /* 402 * Page table entries are set to 1MB, or multiples of 1MB 403 * (not < 1MB). driver uses less bd's so use 1MB bdspace. 404 */ 405 #define BD_SPACE (1 << 20) 406 407 /* Utility/helper methods */ 408 409 /* Write helper method */ 410 static void mvreg_write(struct mvneta_port *pp, u32 offset, u32 data) 411 { 412 writel(data, pp->base + offset); 413 } 414 415 /* Read helper method */ 416 static u32 mvreg_read(struct mvneta_port *pp, u32 offset) 417 { 418 return readl(pp->base + offset); 419 } 420 421 /* Clear all MIB counters */ 422 static void mvneta_mib_counters_clear(struct mvneta_port *pp) 423 { 424 int i; 425 426 /* Perform dummy reads from MIB counters */ 427 for (i = 0; i < MVNETA_MIB_LATE_COLLISION; i += 4) 428 mvreg_read(pp, (MVNETA_MIB_COUNTERS_BASE + i)); 429 } 430 431 /* Rx descriptors helper methods */ 432 433 /* Checks whether the RX descriptor having this status is both the first 434 * and the last descriptor for the RX packet. Each RX packet is currently 435 * received through a single RX descriptor, so not having each RX 436 * descriptor with its first and last bits set is an error 437 */ 438 static int mvneta_rxq_desc_is_first_last(u32 status) 439 { 440 return (status & MVNETA_RXD_FIRST_LAST_DESC) == 441 MVNETA_RXD_FIRST_LAST_DESC; 442 } 443 444 /* Add number of descriptors ready to receive new packets */ 445 static void mvneta_rxq_non_occup_desc_add(struct mvneta_port *pp, 446 struct mvneta_rx_queue *rxq, 447 int ndescs) 448 { 449 /* Only MVNETA_RXQ_ADD_NON_OCCUPIED_MAX (255) descriptors can 450 * be added at once 451 */ 452 while (ndescs > MVNETA_RXQ_ADD_NON_OCCUPIED_MAX) { 453 mvreg_write(pp, MVNETA_RXQ_STATUS_UPDATE_REG(rxq->id), 454 (MVNETA_RXQ_ADD_NON_OCCUPIED_MAX << 455 MVNETA_RXQ_ADD_NON_OCCUPIED_SHIFT)); 456 ndescs -= MVNETA_RXQ_ADD_NON_OCCUPIED_MAX; 457 } 458 459 mvreg_write(pp, MVNETA_RXQ_STATUS_UPDATE_REG(rxq->id), 460 (ndescs << MVNETA_RXQ_ADD_NON_OCCUPIED_SHIFT)); 461 } 462 463 /* Get number of RX descriptors occupied by received packets */ 464 static int mvneta_rxq_busy_desc_num_get(struct mvneta_port *pp, 465 struct mvneta_rx_queue *rxq) 466 { 467 u32 val; 468 469 val = mvreg_read(pp, MVNETA_RXQ_STATUS_REG(rxq->id)); 470 return val & MVNETA_RXQ_OCCUPIED_ALL_MASK; 471 } 472 473 /* Update num of rx desc called upon return from rx path or 474 * from mvneta_rxq_drop_pkts(). 475 */ 476 static void mvneta_rxq_desc_num_update(struct mvneta_port *pp, 477 struct mvneta_rx_queue *rxq, 478 int rx_done, int rx_filled) 479 { 480 u32 val; 481 482 if ((rx_done <= 0xff) && (rx_filled <= 0xff)) { 483 val = rx_done | 484 (rx_filled << MVNETA_RXQ_ADD_NON_OCCUPIED_SHIFT); 485 mvreg_write(pp, MVNETA_RXQ_STATUS_UPDATE_REG(rxq->id), val); 486 return; 487 } 488 489 /* Only 255 descriptors can be added at once */ 490 while ((rx_done > 0) || (rx_filled > 0)) { 491 if (rx_done <= 0xff) { 492 val = rx_done; 493 rx_done = 0; 494 } else { 495 val = 0xff; 496 rx_done -= 0xff; 497 } 498 if (rx_filled <= 0xff) { 499 val |= rx_filled << MVNETA_RXQ_ADD_NON_OCCUPIED_SHIFT; 500 rx_filled = 0; 501 } else { 502 val |= 0xff << MVNETA_RXQ_ADD_NON_OCCUPIED_SHIFT; 503 rx_filled -= 0xff; 504 } 505 mvreg_write(pp, MVNETA_RXQ_STATUS_UPDATE_REG(rxq->id), val); 506 } 507 } 508 509 /* Get pointer to next RX descriptor to be processed by SW */ 510 static struct mvneta_rx_desc * 511 mvneta_rxq_next_desc_get(struct mvneta_rx_queue *rxq) 512 { 513 int rx_desc = rxq->next_desc_to_proc; 514 515 rxq->next_desc_to_proc = MVNETA_QUEUE_NEXT_DESC(rxq, rx_desc); 516 return rxq->descs + rx_desc; 517 } 518 519 /* Tx descriptors helper methods */ 520 521 /* Update HW with number of TX descriptors to be sent */ 522 static void mvneta_txq_pend_desc_add(struct mvneta_port *pp, 523 struct mvneta_tx_queue *txq, 524 int pend_desc) 525 { 526 u32 val; 527 528 /* Only 255 descriptors can be added at once ; Assume caller 529 * process TX desriptors in quanta less than 256 530 */ 531 val = pend_desc; 532 mvreg_write(pp, MVNETA_TXQ_UPDATE_REG(txq->id), val); 533 } 534 535 /* Get pointer to next TX descriptor to be processed (send) by HW */ 536 static struct mvneta_tx_desc * 537 mvneta_txq_next_desc_get(struct mvneta_tx_queue *txq) 538 { 539 int tx_desc = txq->next_desc_to_proc; 540 541 txq->next_desc_to_proc = MVNETA_QUEUE_NEXT_DESC(txq, tx_desc); 542 return txq->descs + tx_desc; 543 } 544 545 /* Set rxq buf size */ 546 static void mvneta_rxq_buf_size_set(struct mvneta_port *pp, 547 struct mvneta_rx_queue *rxq, 548 int buf_size) 549 { 550 u32 val; 551 552 val = mvreg_read(pp, MVNETA_RXQ_SIZE_REG(rxq->id)); 553 554 val &= ~MVNETA_RXQ_BUF_SIZE_MASK; 555 val |= ((buf_size >> 3) << MVNETA_RXQ_BUF_SIZE_SHIFT); 556 557 mvreg_write(pp, MVNETA_RXQ_SIZE_REG(rxq->id), val); 558 } 559 560 /* Start the Ethernet port RX and TX activity */ 561 static void mvneta_port_up(struct mvneta_port *pp) 562 { 563 int queue; 564 u32 q_map; 565 566 /* Enable all initialized TXs. */ 567 mvneta_mib_counters_clear(pp); 568 q_map = 0; 569 for (queue = 0; queue < txq_number; queue++) { 570 struct mvneta_tx_queue *txq = &pp->txqs[queue]; 571 if (txq->descs != NULL) 572 q_map |= (1 << queue); 573 } 574 mvreg_write(pp, MVNETA_TXQ_CMD, q_map); 575 576 /* Enable all initialized RXQs. */ 577 q_map = 0; 578 for (queue = 0; queue < rxq_number; queue++) { 579 struct mvneta_rx_queue *rxq = &pp->rxqs[queue]; 580 if (rxq->descs != NULL) 581 q_map |= (1 << queue); 582 } 583 mvreg_write(pp, MVNETA_RXQ_CMD, q_map); 584 } 585 586 /* Stop the Ethernet port activity */ 587 static void mvneta_port_down(struct mvneta_port *pp) 588 { 589 u32 val; 590 int count; 591 592 /* Stop Rx port activity. Check port Rx activity. */ 593 val = mvreg_read(pp, MVNETA_RXQ_CMD) & MVNETA_RXQ_ENABLE_MASK; 594 595 /* Issue stop command for active channels only */ 596 if (val != 0) 597 mvreg_write(pp, MVNETA_RXQ_CMD, 598 val << MVNETA_RXQ_DISABLE_SHIFT); 599 600 /* Wait for all Rx activity to terminate. */ 601 count = 0; 602 do { 603 if (count++ >= MVNETA_RX_DISABLE_TIMEOUT_MSEC) { 604 netdev_warn(pp->dev, 605 "TIMEOUT for RX stopped ! rx_queue_cmd: 0x08%x\n", 606 val); 607 break; 608 } 609 mdelay(1); 610 611 val = mvreg_read(pp, MVNETA_RXQ_CMD); 612 } while (val & 0xff); 613 614 /* Stop Tx port activity. Check port Tx activity. Issue stop 615 * command for active channels only 616 */ 617 val = (mvreg_read(pp, MVNETA_TXQ_CMD)) & MVNETA_TXQ_ENABLE_MASK; 618 619 if (val != 0) 620 mvreg_write(pp, MVNETA_TXQ_CMD, 621 (val << MVNETA_TXQ_DISABLE_SHIFT)); 622 623 /* Wait for all Tx activity to terminate. */ 624 count = 0; 625 do { 626 if (count++ >= MVNETA_TX_DISABLE_TIMEOUT_MSEC) { 627 netdev_warn(pp->dev, 628 "TIMEOUT for TX stopped status=0x%08x\n", 629 val); 630 break; 631 } 632 mdelay(1); 633 634 /* Check TX Command reg that all Txqs are stopped */ 635 val = mvreg_read(pp, MVNETA_TXQ_CMD); 636 637 } while (val & 0xff); 638 639 /* Double check to verify that TX FIFO is empty */ 640 count = 0; 641 do { 642 if (count++ >= MVNETA_TX_FIFO_EMPTY_TIMEOUT) { 643 netdev_warn(pp->dev, 644 "TX FIFO empty timeout status=0x08%x\n", 645 val); 646 break; 647 } 648 mdelay(1); 649 650 val = mvreg_read(pp, MVNETA_PORT_STATUS); 651 } while (!(val & MVNETA_TX_FIFO_EMPTY) && 652 (val & MVNETA_TX_IN_PRGRS)); 653 654 udelay(200); 655 } 656 657 /* Enable the port by setting the port enable bit of the MAC control register */ 658 static void mvneta_port_enable(struct mvneta_port *pp) 659 { 660 u32 val; 661 662 /* Enable port */ 663 val = mvreg_read(pp, MVNETA_GMAC_CTRL_0); 664 val |= MVNETA_GMAC0_PORT_ENABLE; 665 mvreg_write(pp, MVNETA_GMAC_CTRL_0, val); 666 } 667 668 /* Disable the port and wait for about 200 usec before retuning */ 669 static void mvneta_port_disable(struct mvneta_port *pp) 670 { 671 u32 val; 672 673 /* Reset the Enable bit in the Serial Control Register */ 674 val = mvreg_read(pp, MVNETA_GMAC_CTRL_0); 675 val &= ~MVNETA_GMAC0_PORT_ENABLE; 676 mvreg_write(pp, MVNETA_GMAC_CTRL_0, val); 677 678 udelay(200); 679 } 680 681 /* Multicast tables methods */ 682 683 /* Set all entries in Unicast MAC Table; queue==-1 means reject all */ 684 static void mvneta_set_ucast_table(struct mvneta_port *pp, int queue) 685 { 686 int offset; 687 u32 val; 688 689 if (queue == -1) { 690 val = 0; 691 } else { 692 val = 0x1 | (queue << 1); 693 val |= (val << 24) | (val << 16) | (val << 8); 694 } 695 696 for (offset = 0; offset <= 0xc; offset += 4) 697 mvreg_write(pp, MVNETA_DA_FILT_UCAST_BASE + offset, val); 698 } 699 700 /* Set all entries in Special Multicast MAC Table; queue==-1 means reject all */ 701 static void mvneta_set_special_mcast_table(struct mvneta_port *pp, int queue) 702 { 703 int offset; 704 u32 val; 705 706 if (queue == -1) { 707 val = 0; 708 } else { 709 val = 0x1 | (queue << 1); 710 val |= (val << 24) | (val << 16) | (val << 8); 711 } 712 713 for (offset = 0; offset <= 0xfc; offset += 4) 714 mvreg_write(pp, MVNETA_DA_FILT_SPEC_MCAST + offset, val); 715 } 716 717 /* Set all entries in Other Multicast MAC Table. queue==-1 means reject all */ 718 static void mvneta_set_other_mcast_table(struct mvneta_port *pp, int queue) 719 { 720 int offset; 721 u32 val; 722 723 if (queue == -1) { 724 memset(pp->mcast_count, 0, sizeof(pp->mcast_count)); 725 val = 0; 726 } else { 727 memset(pp->mcast_count, 1, sizeof(pp->mcast_count)); 728 val = 0x1 | (queue << 1); 729 val |= (val << 24) | (val << 16) | (val << 8); 730 } 731 732 for (offset = 0; offset <= 0xfc; offset += 4) 733 mvreg_write(pp, MVNETA_DA_FILT_OTH_MCAST + offset, val); 734 } 735 736 /* This method sets defaults to the NETA port: 737 * Clears interrupt Cause and Mask registers. 738 * Clears all MAC tables. 739 * Sets defaults to all registers. 740 * Resets RX and TX descriptor rings. 741 * Resets PHY. 742 * This method can be called after mvneta_port_down() to return the port 743 * settings to defaults. 744 */ 745 static void mvneta_defaults_set(struct mvneta_port *pp) 746 { 747 int cpu; 748 int queue; 749 u32 val; 750 751 /* Clear all Cause registers */ 752 mvreg_write(pp, MVNETA_INTR_NEW_CAUSE, 0); 753 mvreg_write(pp, MVNETA_INTR_OLD_CAUSE, 0); 754 mvreg_write(pp, MVNETA_INTR_MISC_CAUSE, 0); 755 756 /* Mask all interrupts */ 757 mvreg_write(pp, MVNETA_INTR_NEW_MASK, 0); 758 mvreg_write(pp, MVNETA_INTR_OLD_MASK, 0); 759 mvreg_write(pp, MVNETA_INTR_MISC_MASK, 0); 760 mvreg_write(pp, MVNETA_INTR_ENABLE, 0); 761 762 /* Enable MBUS Retry bit16 */ 763 mvreg_write(pp, MVNETA_MBUS_RETRY, 0x20); 764 765 /* Set CPU queue access map - all CPUs have access to all RX 766 * queues and to all TX queues 767 */ 768 for (cpu = 0; cpu < CONFIG_NR_CPUS; cpu++) 769 mvreg_write(pp, MVNETA_CPU_MAP(cpu), 770 (MVNETA_CPU_RXQ_ACCESS_ALL_MASK | 771 MVNETA_CPU_TXQ_ACCESS_ALL_MASK)); 772 773 /* Reset RX and TX DMAs */ 774 mvreg_write(pp, MVNETA_PORT_RX_RESET, MVNETA_PORT_RX_DMA_RESET); 775 mvreg_write(pp, MVNETA_PORT_TX_RESET, MVNETA_PORT_TX_DMA_RESET); 776 777 /* Disable Legacy WRR, Disable EJP, Release from reset */ 778 mvreg_write(pp, MVNETA_TXQ_CMD_1, 0); 779 for (queue = 0; queue < txq_number; queue++) { 780 mvreg_write(pp, MVETH_TXQ_TOKEN_COUNT_REG(queue), 0); 781 mvreg_write(pp, MVETH_TXQ_TOKEN_CFG_REG(queue), 0); 782 } 783 784 mvreg_write(pp, MVNETA_PORT_TX_RESET, 0); 785 mvreg_write(pp, MVNETA_PORT_RX_RESET, 0); 786 787 /* Set Port Acceleration Mode */ 788 val = MVNETA_ACC_MODE_EXT; 789 mvreg_write(pp, MVNETA_ACC_MODE, val); 790 791 /* Update val of portCfg register accordingly with all RxQueue types */ 792 val = MVNETA_PORT_CONFIG_DEFL_VALUE(rxq_def); 793 mvreg_write(pp, MVNETA_PORT_CONFIG, val); 794 795 val = 0; 796 mvreg_write(pp, MVNETA_PORT_CONFIG_EXTEND, val); 797 mvreg_write(pp, MVNETA_RX_MIN_FRAME_SIZE, 64); 798 799 /* Build PORT_SDMA_CONFIG_REG */ 800 val = 0; 801 802 /* Default burst size */ 803 val |= MVNETA_TX_BRST_SZ_MASK(MVNETA_SDMA_BRST_SIZE_16); 804 val |= MVNETA_RX_BRST_SZ_MASK(MVNETA_SDMA_BRST_SIZE_16); 805 val |= MVNETA_RX_NO_DATA_SWAP | MVNETA_TX_NO_DATA_SWAP; 806 807 /* Assign port SDMA configuration */ 808 mvreg_write(pp, MVNETA_SDMA_CONFIG, val); 809 810 /* Enable PHY polling in hardware for U-Boot */ 811 val = mvreg_read(pp, MVNETA_UNIT_CONTROL); 812 val |= MVNETA_PHY_POLLING_ENABLE; 813 mvreg_write(pp, MVNETA_UNIT_CONTROL, val); 814 815 mvneta_set_ucast_table(pp, -1); 816 mvneta_set_special_mcast_table(pp, -1); 817 mvneta_set_other_mcast_table(pp, -1); 818 } 819 820 /* Set unicast address */ 821 static void mvneta_set_ucast_addr(struct mvneta_port *pp, u8 last_nibble, 822 int queue) 823 { 824 unsigned int unicast_reg; 825 unsigned int tbl_offset; 826 unsigned int reg_offset; 827 828 /* Locate the Unicast table entry */ 829 last_nibble = (0xf & last_nibble); 830 831 /* offset from unicast tbl base */ 832 tbl_offset = (last_nibble / 4) * 4; 833 834 /* offset within the above reg */ 835 reg_offset = last_nibble % 4; 836 837 unicast_reg = mvreg_read(pp, (MVNETA_DA_FILT_UCAST_BASE + tbl_offset)); 838 839 if (queue == -1) { 840 /* Clear accepts frame bit at specified unicast DA tbl entry */ 841 unicast_reg &= ~(0xff << (8 * reg_offset)); 842 } else { 843 unicast_reg &= ~(0xff << (8 * reg_offset)); 844 unicast_reg |= ((0x01 | (queue << 1)) << (8 * reg_offset)); 845 } 846 847 mvreg_write(pp, (MVNETA_DA_FILT_UCAST_BASE + tbl_offset), unicast_reg); 848 } 849 850 /* Set mac address */ 851 static void mvneta_mac_addr_set(struct mvneta_port *pp, unsigned char *addr, 852 int queue) 853 { 854 unsigned int mac_h; 855 unsigned int mac_l; 856 857 if (queue != -1) { 858 mac_l = (addr[4] << 8) | (addr[5]); 859 mac_h = (addr[0] << 24) | (addr[1] << 16) | 860 (addr[2] << 8) | (addr[3] << 0); 861 862 mvreg_write(pp, MVNETA_MAC_ADDR_LOW, mac_l); 863 mvreg_write(pp, MVNETA_MAC_ADDR_HIGH, mac_h); 864 } 865 866 /* Accept frames of this address */ 867 mvneta_set_ucast_addr(pp, addr[5], queue); 868 } 869 870 /* Handle rx descriptor fill by setting buf_cookie and buf_phys_addr */ 871 static void mvneta_rx_desc_fill(struct mvneta_rx_desc *rx_desc, 872 u32 phys_addr, u32 cookie) 873 { 874 rx_desc->buf_cookie = cookie; 875 rx_desc->buf_phys_addr = phys_addr; 876 } 877 878 /* Decrement sent descriptors counter */ 879 static void mvneta_txq_sent_desc_dec(struct mvneta_port *pp, 880 struct mvneta_tx_queue *txq, 881 int sent_desc) 882 { 883 u32 val; 884 885 /* Only 255 TX descriptors can be updated at once */ 886 while (sent_desc > 0xff) { 887 val = 0xff << MVNETA_TXQ_DEC_SENT_SHIFT; 888 mvreg_write(pp, MVNETA_TXQ_UPDATE_REG(txq->id), val); 889 sent_desc = sent_desc - 0xff; 890 } 891 892 val = sent_desc << MVNETA_TXQ_DEC_SENT_SHIFT; 893 mvreg_write(pp, MVNETA_TXQ_UPDATE_REG(txq->id), val); 894 } 895 896 /* Get number of TX descriptors already sent by HW */ 897 static int mvneta_txq_sent_desc_num_get(struct mvneta_port *pp, 898 struct mvneta_tx_queue *txq) 899 { 900 u32 val; 901 int sent_desc; 902 903 val = mvreg_read(pp, MVNETA_TXQ_STATUS_REG(txq->id)); 904 sent_desc = (val & MVNETA_TXQ_SENT_DESC_MASK) >> 905 MVNETA_TXQ_SENT_DESC_SHIFT; 906 907 return sent_desc; 908 } 909 910 /* Display more error info */ 911 static void mvneta_rx_error(struct mvneta_port *pp, 912 struct mvneta_rx_desc *rx_desc) 913 { 914 u32 status = rx_desc->status; 915 916 if (!mvneta_rxq_desc_is_first_last(status)) { 917 netdev_err(pp->dev, 918 "bad rx status %08x (buffer oversize), size=%d\n", 919 status, rx_desc->data_size); 920 return; 921 } 922 923 switch (status & MVNETA_RXD_ERR_CODE_MASK) { 924 case MVNETA_RXD_ERR_CRC: 925 netdev_err(pp->dev, "bad rx status %08x (crc error), size=%d\n", 926 status, rx_desc->data_size); 927 break; 928 case MVNETA_RXD_ERR_OVERRUN: 929 netdev_err(pp->dev, "bad rx status %08x (overrun error), size=%d\n", 930 status, rx_desc->data_size); 931 break; 932 case MVNETA_RXD_ERR_LEN: 933 netdev_err(pp->dev, "bad rx status %08x (max frame length error), size=%d\n", 934 status, rx_desc->data_size); 935 break; 936 case MVNETA_RXD_ERR_RESOURCE: 937 netdev_err(pp->dev, "bad rx status %08x (resource error), size=%d\n", 938 status, rx_desc->data_size); 939 break; 940 } 941 } 942 943 static struct mvneta_rx_queue *mvneta_rxq_handle_get(struct mvneta_port *pp, 944 int rxq) 945 { 946 return &pp->rxqs[rxq]; 947 } 948 949 950 /* Drop packets received by the RXQ and free buffers */ 951 static void mvneta_rxq_drop_pkts(struct mvneta_port *pp, 952 struct mvneta_rx_queue *rxq) 953 { 954 int rx_done; 955 956 rx_done = mvneta_rxq_busy_desc_num_get(pp, rxq); 957 if (rx_done) 958 mvneta_rxq_desc_num_update(pp, rxq, rx_done, rx_done); 959 } 960 961 /* Handle rxq fill: allocates rxq skbs; called when initializing a port */ 962 static int mvneta_rxq_fill(struct mvneta_port *pp, struct mvneta_rx_queue *rxq, 963 int num) 964 { 965 int i; 966 967 for (i = 0; i < num; i++) { 968 u32 addr; 969 970 /* U-Boot special: Fill in the rx buffer addresses */ 971 addr = buffer_loc.rx_buffers + (i * RX_BUFFER_SIZE); 972 mvneta_rx_desc_fill(rxq->descs + i, addr, addr); 973 } 974 975 /* Add this number of RX descriptors as non occupied (ready to 976 * get packets) 977 */ 978 mvneta_rxq_non_occup_desc_add(pp, rxq, i); 979 980 return 0; 981 } 982 983 /* Rx/Tx queue initialization/cleanup methods */ 984 985 /* Create a specified RX queue */ 986 static int mvneta_rxq_init(struct mvneta_port *pp, 987 struct mvneta_rx_queue *rxq) 988 989 { 990 rxq->size = pp->rx_ring_size; 991 992 /* Allocate memory for RX descriptors */ 993 rxq->descs_phys = (dma_addr_t)rxq->descs; 994 if (rxq->descs == NULL) 995 return -ENOMEM; 996 997 rxq->last_desc = rxq->size - 1; 998 999 /* Set Rx descriptors queue starting address */ 1000 mvreg_write(pp, MVNETA_RXQ_BASE_ADDR_REG(rxq->id), rxq->descs_phys); 1001 mvreg_write(pp, MVNETA_RXQ_SIZE_REG(rxq->id), rxq->size); 1002 1003 /* Fill RXQ with buffers from RX pool */ 1004 mvneta_rxq_buf_size_set(pp, rxq, RX_BUFFER_SIZE); 1005 mvneta_rxq_fill(pp, rxq, rxq->size); 1006 1007 return 0; 1008 } 1009 1010 /* Cleanup Rx queue */ 1011 static void mvneta_rxq_deinit(struct mvneta_port *pp, 1012 struct mvneta_rx_queue *rxq) 1013 { 1014 mvneta_rxq_drop_pkts(pp, rxq); 1015 1016 rxq->descs = NULL; 1017 rxq->last_desc = 0; 1018 rxq->next_desc_to_proc = 0; 1019 rxq->descs_phys = 0; 1020 } 1021 1022 /* Create and initialize a tx queue */ 1023 static int mvneta_txq_init(struct mvneta_port *pp, 1024 struct mvneta_tx_queue *txq) 1025 { 1026 txq->size = pp->tx_ring_size; 1027 1028 /* Allocate memory for TX descriptors */ 1029 txq->descs_phys = (dma_addr_t)txq->descs; 1030 if (txq->descs == NULL) 1031 return -ENOMEM; 1032 1033 txq->last_desc = txq->size - 1; 1034 1035 /* Set maximum bandwidth for enabled TXQs */ 1036 mvreg_write(pp, MVETH_TXQ_TOKEN_CFG_REG(txq->id), 0x03ffffff); 1037 mvreg_write(pp, MVETH_TXQ_TOKEN_COUNT_REG(txq->id), 0x3fffffff); 1038 1039 /* Set Tx descriptors queue starting address */ 1040 mvreg_write(pp, MVNETA_TXQ_BASE_ADDR_REG(txq->id), txq->descs_phys); 1041 mvreg_write(pp, MVNETA_TXQ_SIZE_REG(txq->id), txq->size); 1042 1043 return 0; 1044 } 1045 1046 /* Free allocated resources when mvneta_txq_init() fails to allocate memory*/ 1047 static void mvneta_txq_deinit(struct mvneta_port *pp, 1048 struct mvneta_tx_queue *txq) 1049 { 1050 txq->descs = NULL; 1051 txq->last_desc = 0; 1052 txq->next_desc_to_proc = 0; 1053 txq->descs_phys = 0; 1054 1055 /* Set minimum bandwidth for disabled TXQs */ 1056 mvreg_write(pp, MVETH_TXQ_TOKEN_CFG_REG(txq->id), 0); 1057 mvreg_write(pp, MVETH_TXQ_TOKEN_COUNT_REG(txq->id), 0); 1058 1059 /* Set Tx descriptors queue starting address and size */ 1060 mvreg_write(pp, MVNETA_TXQ_BASE_ADDR_REG(txq->id), 0); 1061 mvreg_write(pp, MVNETA_TXQ_SIZE_REG(txq->id), 0); 1062 } 1063 1064 /* Cleanup all Tx queues */ 1065 static void mvneta_cleanup_txqs(struct mvneta_port *pp) 1066 { 1067 int queue; 1068 1069 for (queue = 0; queue < txq_number; queue++) 1070 mvneta_txq_deinit(pp, &pp->txqs[queue]); 1071 } 1072 1073 /* Cleanup all Rx queues */ 1074 static void mvneta_cleanup_rxqs(struct mvneta_port *pp) 1075 { 1076 int queue; 1077 1078 for (queue = 0; queue < rxq_number; queue++) 1079 mvneta_rxq_deinit(pp, &pp->rxqs[queue]); 1080 } 1081 1082 1083 /* Init all Rx queues */ 1084 static int mvneta_setup_rxqs(struct mvneta_port *pp) 1085 { 1086 int queue; 1087 1088 for (queue = 0; queue < rxq_number; queue++) { 1089 int err = mvneta_rxq_init(pp, &pp->rxqs[queue]); 1090 if (err) { 1091 netdev_err(pp->dev, "%s: can't create rxq=%d\n", 1092 __func__, queue); 1093 mvneta_cleanup_rxqs(pp); 1094 return err; 1095 } 1096 } 1097 1098 return 0; 1099 } 1100 1101 /* Init all tx queues */ 1102 static int mvneta_setup_txqs(struct mvneta_port *pp) 1103 { 1104 int queue; 1105 1106 for (queue = 0; queue < txq_number; queue++) { 1107 int err = mvneta_txq_init(pp, &pp->txqs[queue]); 1108 if (err) { 1109 netdev_err(pp->dev, "%s: can't create txq=%d\n", 1110 __func__, queue); 1111 mvneta_cleanup_txqs(pp); 1112 return err; 1113 } 1114 } 1115 1116 return 0; 1117 } 1118 1119 static void mvneta_start_dev(struct mvneta_port *pp) 1120 { 1121 /* start the Rx/Tx activity */ 1122 mvneta_port_enable(pp); 1123 } 1124 1125 static void mvneta_adjust_link(struct udevice *dev) 1126 { 1127 struct mvneta_port *pp = dev_get_priv(dev); 1128 struct phy_device *phydev = pp->phydev; 1129 int status_change = 0; 1130 1131 if (phydev->link) { 1132 if ((pp->speed != phydev->speed) || 1133 (pp->duplex != phydev->duplex)) { 1134 u32 val; 1135 1136 val = mvreg_read(pp, MVNETA_GMAC_AUTONEG_CONFIG); 1137 val &= ~(MVNETA_GMAC_CONFIG_MII_SPEED | 1138 MVNETA_GMAC_CONFIG_GMII_SPEED | 1139 MVNETA_GMAC_CONFIG_FULL_DUPLEX | 1140 MVNETA_GMAC_AN_SPEED_EN | 1141 MVNETA_GMAC_AN_DUPLEX_EN); 1142 1143 if (phydev->duplex) 1144 val |= MVNETA_GMAC_CONFIG_FULL_DUPLEX; 1145 1146 if (phydev->speed == SPEED_1000) 1147 val |= MVNETA_GMAC_CONFIG_GMII_SPEED; 1148 else 1149 val |= MVNETA_GMAC_CONFIG_MII_SPEED; 1150 1151 mvreg_write(pp, MVNETA_GMAC_AUTONEG_CONFIG, val); 1152 1153 pp->duplex = phydev->duplex; 1154 pp->speed = phydev->speed; 1155 } 1156 } 1157 1158 if (phydev->link != pp->link) { 1159 if (!phydev->link) { 1160 pp->duplex = -1; 1161 pp->speed = 0; 1162 } 1163 1164 pp->link = phydev->link; 1165 status_change = 1; 1166 } 1167 1168 if (status_change) { 1169 if (phydev->link) { 1170 u32 val = mvreg_read(pp, MVNETA_GMAC_AUTONEG_CONFIG); 1171 val |= (MVNETA_GMAC_FORCE_LINK_PASS | 1172 MVNETA_GMAC_FORCE_LINK_DOWN); 1173 mvreg_write(pp, MVNETA_GMAC_AUTONEG_CONFIG, val); 1174 mvneta_port_up(pp); 1175 } else { 1176 mvneta_port_down(pp); 1177 } 1178 } 1179 } 1180 1181 static int mvneta_open(struct udevice *dev) 1182 { 1183 struct mvneta_port *pp = dev_get_priv(dev); 1184 int ret; 1185 1186 ret = mvneta_setup_rxqs(pp); 1187 if (ret) 1188 return ret; 1189 1190 ret = mvneta_setup_txqs(pp); 1191 if (ret) 1192 return ret; 1193 1194 mvneta_adjust_link(dev); 1195 1196 mvneta_start_dev(pp); 1197 1198 return 0; 1199 } 1200 1201 /* Initialize hw */ 1202 static int mvneta_init2(struct mvneta_port *pp) 1203 { 1204 int queue; 1205 1206 /* Disable port */ 1207 mvneta_port_disable(pp); 1208 1209 /* Set port default values */ 1210 mvneta_defaults_set(pp); 1211 1212 pp->txqs = kzalloc(txq_number * sizeof(struct mvneta_tx_queue), 1213 GFP_KERNEL); 1214 if (!pp->txqs) 1215 return -ENOMEM; 1216 1217 /* U-Boot special: use preallocated area */ 1218 pp->txqs[0].descs = buffer_loc.tx_descs; 1219 1220 /* Initialize TX descriptor rings */ 1221 for (queue = 0; queue < txq_number; queue++) { 1222 struct mvneta_tx_queue *txq = &pp->txqs[queue]; 1223 txq->id = queue; 1224 txq->size = pp->tx_ring_size; 1225 } 1226 1227 pp->rxqs = kzalloc(rxq_number * sizeof(struct mvneta_rx_queue), 1228 GFP_KERNEL); 1229 if (!pp->rxqs) { 1230 kfree(pp->txqs); 1231 return -ENOMEM; 1232 } 1233 1234 /* U-Boot special: use preallocated area */ 1235 pp->rxqs[0].descs = buffer_loc.rx_descs; 1236 1237 /* Create Rx descriptor rings */ 1238 for (queue = 0; queue < rxq_number; queue++) { 1239 struct mvneta_rx_queue *rxq = &pp->rxqs[queue]; 1240 rxq->id = queue; 1241 rxq->size = pp->rx_ring_size; 1242 } 1243 1244 return 0; 1245 } 1246 1247 /* platform glue : initialize decoding windows */ 1248 1249 /* 1250 * Not like A380, in Armada3700, there are two layers of decode windows for GBE: 1251 * First layer is: GbE Address window that resides inside the GBE unit, 1252 * Second layer is: Fabric address window which is located in the NIC400 1253 * (South Fabric). 1254 * To simplify the address decode configuration for Armada3700, we bypass the 1255 * first layer of GBE decode window by setting the first window to 4GB. 1256 */ 1257 static void mvneta_bypass_mbus_windows(struct mvneta_port *pp) 1258 { 1259 /* 1260 * Set window size to 4GB, to bypass GBE address decode, leave the 1261 * work to MBUS decode window 1262 */ 1263 mvreg_write(pp, MVNETA_WIN_SIZE(0), MVNETA_WIN_SIZE_MASK); 1264 1265 /* Enable GBE address decode window 0 by set bit 0 to 0 */ 1266 clrbits_le32(pp->base + MVNETA_BASE_ADDR_ENABLE, 1267 MVNETA_BASE_ADDR_ENABLE_BIT); 1268 1269 /* Set GBE address decode window 0 to full Access (read or write) */ 1270 setbits_le32(pp->base + MVNETA_PORT_ACCESS_PROTECT, 1271 MVNETA_PORT_ACCESS_PROTECT_WIN0_RW); 1272 } 1273 1274 static void mvneta_conf_mbus_windows(struct mvneta_port *pp) 1275 { 1276 const struct mbus_dram_target_info *dram; 1277 u32 win_enable; 1278 u32 win_protect; 1279 int i; 1280 1281 dram = mvebu_mbus_dram_info(); 1282 for (i = 0; i < 6; i++) { 1283 mvreg_write(pp, MVNETA_WIN_BASE(i), 0); 1284 mvreg_write(pp, MVNETA_WIN_SIZE(i), 0); 1285 1286 if (i < 4) 1287 mvreg_write(pp, MVNETA_WIN_REMAP(i), 0); 1288 } 1289 1290 win_enable = 0x3f; 1291 win_protect = 0; 1292 1293 for (i = 0; i < dram->num_cs; i++) { 1294 const struct mbus_dram_window *cs = dram->cs + i; 1295 mvreg_write(pp, MVNETA_WIN_BASE(i), (cs->base & 0xffff0000) | 1296 (cs->mbus_attr << 8) | dram->mbus_dram_target_id); 1297 1298 mvreg_write(pp, MVNETA_WIN_SIZE(i), 1299 (cs->size - 1) & 0xffff0000); 1300 1301 win_enable &= ~(1 << i); 1302 win_protect |= 3 << (2 * i); 1303 } 1304 1305 mvreg_write(pp, MVNETA_BASE_ADDR_ENABLE, win_enable); 1306 } 1307 1308 /* Power up the port */ 1309 static int mvneta_port_power_up(struct mvneta_port *pp, int phy_mode) 1310 { 1311 u32 ctrl; 1312 1313 /* MAC Cause register should be cleared */ 1314 mvreg_write(pp, MVNETA_UNIT_INTR_CAUSE, 0); 1315 1316 ctrl = mvreg_read(pp, MVNETA_GMAC_CTRL_2); 1317 1318 /* Even though it might look weird, when we're configured in 1319 * SGMII or QSGMII mode, the RGMII bit needs to be set. 1320 */ 1321 switch (phy_mode) { 1322 case PHY_INTERFACE_MODE_QSGMII: 1323 mvreg_write(pp, MVNETA_SERDES_CFG, MVNETA_QSGMII_SERDES_PROTO); 1324 ctrl |= MVNETA_GMAC2_PCS_ENABLE | MVNETA_GMAC2_PORT_RGMII; 1325 break; 1326 case PHY_INTERFACE_MODE_SGMII: 1327 mvreg_write(pp, MVNETA_SERDES_CFG, MVNETA_SGMII_SERDES_PROTO); 1328 ctrl |= MVNETA_GMAC2_PCS_ENABLE | MVNETA_GMAC2_PORT_RGMII; 1329 break; 1330 case PHY_INTERFACE_MODE_RGMII: 1331 case PHY_INTERFACE_MODE_RGMII_ID: 1332 ctrl |= MVNETA_GMAC2_PORT_RGMII; 1333 break; 1334 default: 1335 return -EINVAL; 1336 } 1337 1338 /* Cancel Port Reset */ 1339 ctrl &= ~MVNETA_GMAC2_PORT_RESET; 1340 mvreg_write(pp, MVNETA_GMAC_CTRL_2, ctrl); 1341 1342 while ((mvreg_read(pp, MVNETA_GMAC_CTRL_2) & 1343 MVNETA_GMAC2_PORT_RESET) != 0) 1344 continue; 1345 1346 return 0; 1347 } 1348 1349 /* Device initialization routine */ 1350 static int mvneta_init(struct udevice *dev) 1351 { 1352 struct eth_pdata *pdata = dev_get_platdata(dev); 1353 struct mvneta_port *pp = dev_get_priv(dev); 1354 int err; 1355 1356 pp->tx_ring_size = MVNETA_MAX_TXD; 1357 pp->rx_ring_size = MVNETA_MAX_RXD; 1358 1359 err = mvneta_init2(pp); 1360 if (err < 0) { 1361 dev_err(&pdev->dev, "can't init eth hal\n"); 1362 return err; 1363 } 1364 1365 mvneta_mac_addr_set(pp, pdata->enetaddr, rxq_def); 1366 1367 err = mvneta_port_power_up(pp, pp->phy_interface); 1368 if (err < 0) { 1369 dev_err(&pdev->dev, "can't power up port\n"); 1370 return err; 1371 } 1372 1373 /* Call open() now as it needs to be done before runing send() */ 1374 mvneta_open(dev); 1375 1376 return 0; 1377 } 1378 1379 /* U-Boot only functions follow here */ 1380 1381 /* SMI / MDIO functions */ 1382 1383 static int smi_wait_ready(struct mvneta_port *pp) 1384 { 1385 u32 timeout = MVNETA_SMI_TIMEOUT; 1386 u32 smi_reg; 1387 1388 /* wait till the SMI is not busy */ 1389 do { 1390 /* read smi register */ 1391 smi_reg = mvreg_read(pp, MVNETA_SMI); 1392 if (timeout-- == 0) { 1393 printf("Error: SMI busy timeout\n"); 1394 return -EFAULT; 1395 } 1396 } while (smi_reg & MVNETA_SMI_BUSY); 1397 1398 return 0; 1399 } 1400 1401 /* 1402 * mvneta_mdio_read - miiphy_read callback function. 1403 * 1404 * Returns 16bit phy register value, or 0xffff on error 1405 */ 1406 static int mvneta_mdio_read(struct mii_dev *bus, int addr, int devad, int reg) 1407 { 1408 struct mvneta_port *pp = bus->priv; 1409 u32 smi_reg; 1410 u32 timeout; 1411 1412 /* check parameters */ 1413 if (addr > MVNETA_PHY_ADDR_MASK) { 1414 printf("Error: Invalid PHY address %d\n", addr); 1415 return -EFAULT; 1416 } 1417 1418 if (reg > MVNETA_PHY_REG_MASK) { 1419 printf("Err: Invalid register offset %d\n", reg); 1420 return -EFAULT; 1421 } 1422 1423 /* wait till the SMI is not busy */ 1424 if (smi_wait_ready(pp) < 0) 1425 return -EFAULT; 1426 1427 /* fill the phy address and regiser offset and read opcode */ 1428 smi_reg = (addr << MVNETA_SMI_DEV_ADDR_OFFS) 1429 | (reg << MVNETA_SMI_REG_ADDR_OFFS) 1430 | MVNETA_SMI_OPCODE_READ; 1431 1432 /* write the smi register */ 1433 mvreg_write(pp, MVNETA_SMI, smi_reg); 1434 1435 /* wait till read value is ready */ 1436 timeout = MVNETA_SMI_TIMEOUT; 1437 1438 do { 1439 /* read smi register */ 1440 smi_reg = mvreg_read(pp, MVNETA_SMI); 1441 if (timeout-- == 0) { 1442 printf("Err: SMI read ready timeout\n"); 1443 return -EFAULT; 1444 } 1445 } while (!(smi_reg & MVNETA_SMI_READ_VALID)); 1446 1447 /* Wait for the data to update in the SMI register */ 1448 for (timeout = 0; timeout < MVNETA_SMI_TIMEOUT; timeout++) 1449 ; 1450 1451 return mvreg_read(pp, MVNETA_SMI) & MVNETA_SMI_DATA_MASK; 1452 } 1453 1454 /* 1455 * mvneta_mdio_write - miiphy_write callback function. 1456 * 1457 * Returns 0 if write succeed, -EINVAL on bad parameters 1458 * -ETIME on timeout 1459 */ 1460 static int mvneta_mdio_write(struct mii_dev *bus, int addr, int devad, int reg, 1461 u16 value) 1462 { 1463 struct mvneta_port *pp = bus->priv; 1464 u32 smi_reg; 1465 1466 /* check parameters */ 1467 if (addr > MVNETA_PHY_ADDR_MASK) { 1468 printf("Error: Invalid PHY address %d\n", addr); 1469 return -EFAULT; 1470 } 1471 1472 if (reg > MVNETA_PHY_REG_MASK) { 1473 printf("Err: Invalid register offset %d\n", reg); 1474 return -EFAULT; 1475 } 1476 1477 /* wait till the SMI is not busy */ 1478 if (smi_wait_ready(pp) < 0) 1479 return -EFAULT; 1480 1481 /* fill the phy addr and reg offset and write opcode and data */ 1482 smi_reg = value << MVNETA_SMI_DATA_OFFS; 1483 smi_reg |= (addr << MVNETA_SMI_DEV_ADDR_OFFS) 1484 | (reg << MVNETA_SMI_REG_ADDR_OFFS); 1485 smi_reg &= ~MVNETA_SMI_OPCODE_READ; 1486 1487 /* write the smi register */ 1488 mvreg_write(pp, MVNETA_SMI, smi_reg); 1489 1490 return 0; 1491 } 1492 1493 static int mvneta_start(struct udevice *dev) 1494 { 1495 struct mvneta_port *pp = dev_get_priv(dev); 1496 struct phy_device *phydev; 1497 1498 mvneta_port_power_up(pp, pp->phy_interface); 1499 1500 if (!pp->init || pp->link == 0) { 1501 /* Set phy address of the port */ 1502 mvreg_write(pp, MVNETA_PHY_ADDR, pp->phyaddr); 1503 phydev = phy_connect(pp->bus, pp->phyaddr, dev, 1504 pp->phy_interface); 1505 1506 pp->phydev = phydev; 1507 phy_config(phydev); 1508 phy_startup(phydev); 1509 if (!phydev->link) { 1510 printf("%s: No link.\n", phydev->dev->name); 1511 return -1; 1512 } 1513 1514 /* Full init on first call */ 1515 mvneta_init(dev); 1516 pp->init = 1; 1517 } else { 1518 /* Upon all following calls, this is enough */ 1519 mvneta_port_up(pp); 1520 mvneta_port_enable(pp); 1521 } 1522 1523 return 0; 1524 } 1525 1526 static int mvneta_send(struct udevice *dev, void *packet, int length) 1527 { 1528 struct mvneta_port *pp = dev_get_priv(dev); 1529 struct mvneta_tx_queue *txq = &pp->txqs[0]; 1530 struct mvneta_tx_desc *tx_desc; 1531 int sent_desc; 1532 u32 timeout = 0; 1533 1534 /* Get a descriptor for the first part of the packet */ 1535 tx_desc = mvneta_txq_next_desc_get(txq); 1536 1537 tx_desc->buf_phys_addr = (u32)(uintptr_t)packet; 1538 tx_desc->data_size = length; 1539 flush_dcache_range((ulong)packet, 1540 (ulong)packet + ALIGN(length, PKTALIGN)); 1541 1542 /* First and Last descriptor */ 1543 tx_desc->command = MVNETA_TX_L4_CSUM_NOT | MVNETA_TXD_FLZ_DESC; 1544 mvneta_txq_pend_desc_add(pp, txq, 1); 1545 1546 /* Wait for packet to be sent (queue might help with speed here) */ 1547 sent_desc = mvneta_txq_sent_desc_num_get(pp, txq); 1548 while (!sent_desc) { 1549 if (timeout++ > 10000) { 1550 printf("timeout: packet not sent\n"); 1551 return -1; 1552 } 1553 sent_desc = mvneta_txq_sent_desc_num_get(pp, txq); 1554 } 1555 1556 /* txDone has increased - hw sent packet */ 1557 mvneta_txq_sent_desc_dec(pp, txq, sent_desc); 1558 1559 return 0; 1560 } 1561 1562 static int mvneta_recv(struct udevice *dev, int flags, uchar **packetp) 1563 { 1564 struct mvneta_port *pp = dev_get_priv(dev); 1565 int rx_done; 1566 struct mvneta_rx_queue *rxq; 1567 int rx_bytes = 0; 1568 1569 /* get rx queue */ 1570 rxq = mvneta_rxq_handle_get(pp, rxq_def); 1571 rx_done = mvneta_rxq_busy_desc_num_get(pp, rxq); 1572 1573 if (rx_done) { 1574 struct mvneta_rx_desc *rx_desc; 1575 unsigned char *data; 1576 u32 rx_status; 1577 1578 /* 1579 * No cache invalidation needed here, since the desc's are 1580 * located in a uncached memory region 1581 */ 1582 rx_desc = mvneta_rxq_next_desc_get(rxq); 1583 1584 rx_status = rx_desc->status; 1585 if (!mvneta_rxq_desc_is_first_last(rx_status) || 1586 (rx_status & MVNETA_RXD_ERR_SUMMARY)) { 1587 mvneta_rx_error(pp, rx_desc); 1588 /* leave the descriptor untouched */ 1589 return -EIO; 1590 } 1591 1592 /* 2 bytes for marvell header. 4 bytes for crc */ 1593 rx_bytes = rx_desc->data_size - 6; 1594 1595 /* give packet to stack - skip on first 2 bytes */ 1596 data = (u8 *)(uintptr_t)rx_desc->buf_cookie + 2; 1597 /* 1598 * No cache invalidation needed here, since the rx_buffer's are 1599 * located in a uncached memory region 1600 */ 1601 *packetp = data; 1602 1603 mvneta_rxq_desc_num_update(pp, rxq, rx_done, rx_done); 1604 } 1605 1606 return rx_bytes; 1607 } 1608 1609 static int mvneta_probe(struct udevice *dev) 1610 { 1611 struct eth_pdata *pdata = dev_get_platdata(dev); 1612 struct mvneta_port *pp = dev_get_priv(dev); 1613 void *blob = (void *)gd->fdt_blob; 1614 int node = dev->of_offset; 1615 struct mii_dev *bus; 1616 unsigned long addr; 1617 void *bd_space; 1618 1619 /* 1620 * Allocate buffer area for descs and rx_buffers. This is only 1621 * done once for all interfaces. As only one interface can 1622 * be active. Make this area DMA save by disabling the D-cache 1623 */ 1624 if (!buffer_loc.tx_descs) { 1625 /* Align buffer area for descs and rx_buffers to 1MiB */ 1626 bd_space = memalign(1 << MMU_SECTION_SHIFT, BD_SPACE); 1627 mmu_set_region_dcache_behaviour((phys_addr_t)bd_space, BD_SPACE, 1628 DCACHE_OFF); 1629 buffer_loc.tx_descs = (struct mvneta_tx_desc *)bd_space; 1630 buffer_loc.rx_descs = (struct mvneta_rx_desc *) 1631 ((phys_addr_t)bd_space + 1632 MVNETA_MAX_TXD * sizeof(struct mvneta_tx_desc)); 1633 buffer_loc.rx_buffers = (phys_addr_t) 1634 (bd_space + 1635 MVNETA_MAX_TXD * sizeof(struct mvneta_tx_desc) + 1636 MVNETA_MAX_RXD * sizeof(struct mvneta_rx_desc)); 1637 } 1638 1639 pp->base = (void __iomem *)pdata->iobase; 1640 1641 /* Configure MBUS address windows */ 1642 if (of_device_is_compatible(dev, "marvell,armada-3700-neta")) 1643 mvneta_bypass_mbus_windows(pp); 1644 else 1645 mvneta_conf_mbus_windows(pp); 1646 1647 /* PHY interface is already decoded in mvneta_ofdata_to_platdata() */ 1648 pp->phy_interface = pdata->phy_interface; 1649 1650 /* Now read phyaddr from DT */ 1651 addr = fdtdec_get_int(blob, node, "phy", 0); 1652 addr = fdt_node_offset_by_phandle(blob, addr); 1653 pp->phyaddr = fdtdec_get_int(blob, addr, "reg", 0); 1654 1655 bus = mdio_alloc(); 1656 if (!bus) { 1657 printf("Failed to allocate MDIO bus\n"); 1658 return -ENOMEM; 1659 } 1660 1661 bus->read = mvneta_mdio_read; 1662 bus->write = mvneta_mdio_write; 1663 snprintf(bus->name, sizeof(bus->name), dev->name); 1664 bus->priv = (void *)pp; 1665 pp->bus = bus; 1666 1667 return mdio_register(bus); 1668 } 1669 1670 static void mvneta_stop(struct udevice *dev) 1671 { 1672 struct mvneta_port *pp = dev_get_priv(dev); 1673 1674 mvneta_port_down(pp); 1675 mvneta_port_disable(pp); 1676 } 1677 1678 static const struct eth_ops mvneta_ops = { 1679 .start = mvneta_start, 1680 .send = mvneta_send, 1681 .recv = mvneta_recv, 1682 .stop = mvneta_stop, 1683 }; 1684 1685 static int mvneta_ofdata_to_platdata(struct udevice *dev) 1686 { 1687 struct eth_pdata *pdata = dev_get_platdata(dev); 1688 const char *phy_mode; 1689 1690 pdata->iobase = dev_get_addr(dev); 1691 1692 /* Get phy-mode / phy_interface from DT */ 1693 pdata->phy_interface = -1; 1694 phy_mode = fdt_getprop(gd->fdt_blob, dev->of_offset, "phy-mode", NULL); 1695 if (phy_mode) 1696 pdata->phy_interface = phy_get_interface_by_name(phy_mode); 1697 if (pdata->phy_interface == -1) { 1698 debug("%s: Invalid PHY interface '%s'\n", __func__, phy_mode); 1699 return -EINVAL; 1700 } 1701 1702 return 0; 1703 } 1704 1705 static const struct udevice_id mvneta_ids[] = { 1706 { .compatible = "marvell,armada-370-neta" }, 1707 { .compatible = "marvell,armada-xp-neta" }, 1708 { .compatible = "marvell,armada-3700-neta" }, 1709 { } 1710 }; 1711 1712 U_BOOT_DRIVER(mvneta) = { 1713 .name = "mvneta", 1714 .id = UCLASS_ETH, 1715 .of_match = mvneta_ids, 1716 .ofdata_to_platdata = mvneta_ofdata_to_platdata, 1717 .probe = mvneta_probe, 1718 .ops = &mvneta_ops, 1719 .priv_auto_alloc_size = sizeof(struct mvneta_port), 1720 .platdata_auto_alloc_size = sizeof(struct eth_pdata), 1721 }; 1722