1 /* 2 * (C) Copyright 2009 3 * Marvell Semiconductor <www.marvell.com> 4 * Written-by: Prafulla Wadaskar <prafulla@marvell.com> 5 * 6 * (C) Copyright 2003 7 * Ingo Assmus <ingo.assmus@keymile.com> 8 * 9 * based on - Driver for MV64360X ethernet ports 10 * Copyright (C) 2002 rabeeh@galileo.co.il 11 * 12 * SPDX-License-Identifier: GPL-2.0+ 13 */ 14 15 #include <common.h> 16 #include <net.h> 17 #include <malloc.h> 18 #include <miiphy.h> 19 #include <asm/io.h> 20 #include <asm/errno.h> 21 #include <asm/types.h> 22 #include <asm/system.h> 23 #include <asm/byteorder.h> 24 #include <asm/arch/cpu.h> 25 26 #if defined(CONFIG_KIRKWOOD) 27 #include <asm/arch/kirkwood.h> 28 #elif defined(CONFIG_ORION5X) 29 #include <asm/arch/orion5x.h> 30 #elif defined(CONFIG_DOVE) 31 #include <asm/arch/dove.h> 32 #endif 33 34 #include "mvgbe.h" 35 36 DECLARE_GLOBAL_DATA_PTR; 37 38 #define MV_PHY_ADR_REQUEST 0xee 39 #define MVGBE_SMI_REG (((struct mvgbe_registers *)MVGBE0_BASE)->smi) 40 41 #if defined(CONFIG_PHYLIB) || defined(CONFIG_MII) || defined(CONFIG_CMD_MII) 42 /* 43 * smi_reg_read - miiphy_read callback function. 44 * 45 * Returns 16bit phy register value, or 0xffff on error 46 */ 47 static int smi_reg_read(const char *devname, u8 phy_adr, u8 reg_ofs, u16 * data) 48 { 49 struct eth_device *dev = eth_get_dev_by_name(devname); 50 struct mvgbe_device *dmvgbe = to_mvgbe(dev); 51 struct mvgbe_registers *regs = dmvgbe->regs; 52 u32 smi_reg; 53 u32 timeout; 54 55 /* Phyadr read request */ 56 if (phy_adr == MV_PHY_ADR_REQUEST && 57 reg_ofs == MV_PHY_ADR_REQUEST) { 58 /* */ 59 *data = (u16) (MVGBE_REG_RD(regs->phyadr) & PHYADR_MASK); 60 return 0; 61 } 62 /* check parameters */ 63 if (phy_adr > PHYADR_MASK) { 64 printf("Err..(%s) Invalid PHY address %d\n", 65 __FUNCTION__, phy_adr); 66 return -EFAULT; 67 } 68 if (reg_ofs > PHYREG_MASK) { 69 printf("Err..(%s) Invalid register offset %d\n", 70 __FUNCTION__, reg_ofs); 71 return -EFAULT; 72 } 73 74 timeout = MVGBE_PHY_SMI_TIMEOUT; 75 /* wait till the SMI is not busy */ 76 do { 77 /* read smi register */ 78 smi_reg = MVGBE_REG_RD(MVGBE_SMI_REG); 79 if (timeout-- == 0) { 80 printf("Err..(%s) SMI busy timeout\n", __FUNCTION__); 81 return -EFAULT; 82 } 83 } while (smi_reg & MVGBE_PHY_SMI_BUSY_MASK); 84 85 /* fill the phy address and regiser offset and read opcode */ 86 smi_reg = (phy_adr << MVGBE_PHY_SMI_DEV_ADDR_OFFS) 87 | (reg_ofs << MVGBE_SMI_REG_ADDR_OFFS) 88 | MVGBE_PHY_SMI_OPCODE_READ; 89 90 /* write the smi register */ 91 MVGBE_REG_WR(MVGBE_SMI_REG, smi_reg); 92 93 /*wait till read value is ready */ 94 timeout = MVGBE_PHY_SMI_TIMEOUT; 95 96 do { 97 /* read smi register */ 98 smi_reg = MVGBE_REG_RD(MVGBE_SMI_REG); 99 if (timeout-- == 0) { 100 printf("Err..(%s) SMI read ready timeout\n", 101 __FUNCTION__); 102 return -EFAULT; 103 } 104 } while (!(smi_reg & MVGBE_PHY_SMI_READ_VALID_MASK)); 105 106 /* Wait for the data to update in the SMI register */ 107 for (timeout = 0; timeout < MVGBE_PHY_SMI_TIMEOUT; timeout++) 108 ; 109 110 *data = (u16) (MVGBE_REG_RD(MVGBE_SMI_REG) & MVGBE_PHY_SMI_DATA_MASK); 111 112 debug("%s:(adr %d, off %d) value= %04x\n", __FUNCTION__, phy_adr, 113 reg_ofs, *data); 114 115 return 0; 116 } 117 118 /* 119 * smi_reg_write - imiiphy_write callback function. 120 * 121 * Returns 0 if write succeed, -EINVAL on bad parameters 122 * -ETIME on timeout 123 */ 124 static int smi_reg_write(const char *devname, u8 phy_adr, u8 reg_ofs, u16 data) 125 { 126 struct eth_device *dev = eth_get_dev_by_name(devname); 127 struct mvgbe_device *dmvgbe = to_mvgbe(dev); 128 struct mvgbe_registers *regs = dmvgbe->regs; 129 u32 smi_reg; 130 u32 timeout; 131 132 /* Phyadr write request*/ 133 if (phy_adr == MV_PHY_ADR_REQUEST && 134 reg_ofs == MV_PHY_ADR_REQUEST) { 135 MVGBE_REG_WR(regs->phyadr, data); 136 return 0; 137 } 138 139 /* check parameters */ 140 if (phy_adr > PHYADR_MASK) { 141 printf("Err..(%s) Invalid phy address\n", __FUNCTION__); 142 return -EINVAL; 143 } 144 if (reg_ofs > PHYREG_MASK) { 145 printf("Err..(%s) Invalid register offset\n", __FUNCTION__); 146 return -EINVAL; 147 } 148 149 /* wait till the SMI is not busy */ 150 timeout = MVGBE_PHY_SMI_TIMEOUT; 151 do { 152 /* read smi register */ 153 smi_reg = MVGBE_REG_RD(MVGBE_SMI_REG); 154 if (timeout-- == 0) { 155 printf("Err..(%s) SMI busy timeout\n", __FUNCTION__); 156 return -ETIME; 157 } 158 } while (smi_reg & MVGBE_PHY_SMI_BUSY_MASK); 159 160 /* fill the phy addr and reg offset and write opcode and data */ 161 smi_reg = (data << MVGBE_PHY_SMI_DATA_OFFS); 162 smi_reg |= (phy_adr << MVGBE_PHY_SMI_DEV_ADDR_OFFS) 163 | (reg_ofs << MVGBE_SMI_REG_ADDR_OFFS); 164 smi_reg &= ~MVGBE_PHY_SMI_OPCODE_READ; 165 166 /* write the smi register */ 167 MVGBE_REG_WR(MVGBE_SMI_REG, smi_reg); 168 169 return 0; 170 } 171 #endif 172 173 #if defined(CONFIG_PHYLIB) 174 int mvgbe_phy_read(struct mii_dev *bus, int phy_addr, int dev_addr, 175 int reg_addr) 176 { 177 u16 data; 178 int ret; 179 ret = smi_reg_read(bus->name, phy_addr, reg_addr, &data); 180 if (ret) 181 return ret; 182 return data; 183 } 184 185 int mvgbe_phy_write(struct mii_dev *bus, int phy_addr, int dev_addr, 186 int reg_addr, u16 data) 187 { 188 return smi_reg_write(bus->name, phy_addr, reg_addr, data); 189 } 190 #endif 191 192 /* Stop and checks all queues */ 193 static void stop_queue(u32 * qreg) 194 { 195 u32 reg_data; 196 197 reg_data = readl(qreg); 198 199 if (reg_data & 0xFF) { 200 /* Issue stop command for active channels only */ 201 writel((reg_data << 8), qreg); 202 203 /* Wait for all queue activity to terminate. */ 204 do { 205 /* 206 * Check port cause register that all queues 207 * are stopped 208 */ 209 reg_data = readl(qreg); 210 } 211 while (reg_data & 0xFF); 212 } 213 } 214 215 /* 216 * set_access_control - Config address decode parameters for Ethernet unit 217 * 218 * This function configures the address decode parameters for the Gigabit 219 * Ethernet Controller according the given parameters struct. 220 * 221 * @regs Register struct pointer. 222 * @param Address decode parameter struct. 223 */ 224 static void set_access_control(struct mvgbe_registers *regs, 225 struct mvgbe_winparam *param) 226 { 227 u32 access_prot_reg; 228 229 /* Set access control register */ 230 access_prot_reg = MVGBE_REG_RD(regs->epap); 231 /* clear window permission */ 232 access_prot_reg &= (~(3 << (param->win * 2))); 233 access_prot_reg |= (param->access_ctrl << (param->win * 2)); 234 MVGBE_REG_WR(regs->epap, access_prot_reg); 235 236 /* Set window Size reg (SR) */ 237 MVGBE_REG_WR(regs->barsz[param->win].size, 238 (((param->size / 0x10000) - 1) << 16)); 239 240 /* Set window Base address reg (BA) */ 241 MVGBE_REG_WR(regs->barsz[param->win].bar, 242 (param->target | param->attrib | param->base_addr)); 243 /* High address remap reg (HARR) */ 244 if (param->win < 4) 245 MVGBE_REG_WR(regs->ha_remap[param->win], param->high_addr); 246 247 /* Base address enable reg (BARER) */ 248 if (param->enable == 1) 249 MVGBE_REG_BITS_RESET(regs->bare, (1 << param->win)); 250 else 251 MVGBE_REG_BITS_SET(regs->bare, (1 << param->win)); 252 } 253 254 static void set_dram_access(struct mvgbe_registers *regs) 255 { 256 struct mvgbe_winparam win_param; 257 int i; 258 259 for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) { 260 /* Set access parameters for DRAM bank i */ 261 win_param.win = i; /* Use Ethernet window i */ 262 /* Window target - DDR */ 263 win_param.target = MVGBE_TARGET_DRAM; 264 /* Enable full access */ 265 win_param.access_ctrl = EWIN_ACCESS_FULL; 266 win_param.high_addr = 0; 267 /* Get bank base and size */ 268 win_param.base_addr = gd->bd->bi_dram[i].start; 269 win_param.size = gd->bd->bi_dram[i].size; 270 if (win_param.size == 0) 271 win_param.enable = 0; 272 else 273 win_param.enable = 1; /* Enable the access */ 274 275 /* Enable DRAM bank */ 276 switch (i) { 277 case 0: 278 win_param.attrib = EBAR_DRAM_CS0; 279 break; 280 case 1: 281 win_param.attrib = EBAR_DRAM_CS1; 282 break; 283 case 2: 284 win_param.attrib = EBAR_DRAM_CS2; 285 break; 286 case 3: 287 win_param.attrib = EBAR_DRAM_CS3; 288 break; 289 default: 290 /* invalid bank, disable access */ 291 win_param.enable = 0; 292 win_param.attrib = 0; 293 break; 294 } 295 /* Set the access control for address window(EPAPR) RD/WR */ 296 set_access_control(regs, &win_param); 297 } 298 } 299 300 /* 301 * port_init_mac_tables - Clear all entrance in the UC, SMC and OMC tables 302 * 303 * Go through all the DA filter tables (Unicast, Special Multicast & Other 304 * Multicast) and set each entry to 0. 305 */ 306 static void port_init_mac_tables(struct mvgbe_registers *regs) 307 { 308 int table_index; 309 310 /* Clear DA filter unicast table (Ex_dFUT) */ 311 for (table_index = 0; table_index < 4; ++table_index) 312 MVGBE_REG_WR(regs->dfut[table_index], 0); 313 314 for (table_index = 0; table_index < 64; ++table_index) { 315 /* Clear DA filter special multicast table (Ex_dFSMT) */ 316 MVGBE_REG_WR(regs->dfsmt[table_index], 0); 317 /* Clear DA filter other multicast table (Ex_dFOMT) */ 318 MVGBE_REG_WR(regs->dfomt[table_index], 0); 319 } 320 } 321 322 /* 323 * port_uc_addr - This function Set the port unicast address table 324 * 325 * This function locates the proper entry in the Unicast table for the 326 * specified MAC nibble and sets its properties according to function 327 * parameters. 328 * This function add/removes MAC addresses from the port unicast address 329 * table. 330 * 331 * @uc_nibble Unicast MAC Address last nibble. 332 * @option 0 = Add, 1 = remove address. 333 * 334 * RETURN: 1 if output succeeded. 0 if option parameter is invalid. 335 */ 336 static int port_uc_addr(struct mvgbe_registers *regs, u8 uc_nibble, 337 int option) 338 { 339 u32 unicast_reg; 340 u32 tbl_offset; 341 u32 reg_offset; 342 343 /* Locate the Unicast table entry */ 344 uc_nibble = (0xf & uc_nibble); 345 /* Register offset from unicast table base */ 346 tbl_offset = (uc_nibble / 4); 347 /* Entry offset within the above register */ 348 reg_offset = uc_nibble % 4; 349 350 switch (option) { 351 case REJECT_MAC_ADDR: 352 /* 353 * Clear accepts frame bit at specified unicast 354 * DA table entry 355 */ 356 unicast_reg = MVGBE_REG_RD(regs->dfut[tbl_offset]); 357 unicast_reg &= (0xFF << (8 * reg_offset)); 358 MVGBE_REG_WR(regs->dfut[tbl_offset], unicast_reg); 359 break; 360 case ACCEPT_MAC_ADDR: 361 /* Set accepts frame bit at unicast DA filter table entry */ 362 unicast_reg = MVGBE_REG_RD(regs->dfut[tbl_offset]); 363 unicast_reg &= (0xFF << (8 * reg_offset)); 364 unicast_reg |= ((0x01 | (RXUQ << 1)) << (8 * reg_offset)); 365 MVGBE_REG_WR(regs->dfut[tbl_offset], unicast_reg); 366 break; 367 default: 368 return 0; 369 } 370 return 1; 371 } 372 373 /* 374 * port_uc_addr_set - This function Set the port Unicast address. 375 */ 376 static void port_uc_addr_set(struct mvgbe_registers *regs, u8 * p_addr) 377 { 378 u32 mac_h; 379 u32 mac_l; 380 381 mac_l = (p_addr[4] << 8) | (p_addr[5]); 382 mac_h = (p_addr[0] << 24) | (p_addr[1] << 16) | (p_addr[2] << 8) | 383 (p_addr[3] << 0); 384 385 MVGBE_REG_WR(regs->macal, mac_l); 386 MVGBE_REG_WR(regs->macah, mac_h); 387 388 /* Accept frames of this address */ 389 port_uc_addr(regs, p_addr[5], ACCEPT_MAC_ADDR); 390 } 391 392 /* 393 * mvgbe_init_rx_desc_ring - Curve a Rx chain desc list and buffer in memory. 394 */ 395 static void mvgbe_init_rx_desc_ring(struct mvgbe_device *dmvgbe) 396 { 397 struct mvgbe_rxdesc *p_rx_desc; 398 int i; 399 400 /* initialize the Rx descriptors ring */ 401 p_rx_desc = dmvgbe->p_rxdesc; 402 for (i = 0; i < RINGSZ; i++) { 403 p_rx_desc->cmd_sts = 404 MVGBE_BUFFER_OWNED_BY_DMA | MVGBE_RX_EN_INTERRUPT; 405 p_rx_desc->buf_size = PKTSIZE_ALIGN; 406 p_rx_desc->byte_cnt = 0; 407 p_rx_desc->buf_ptr = dmvgbe->p_rxbuf + i * PKTSIZE_ALIGN; 408 if (i == (RINGSZ - 1)) 409 p_rx_desc->nxtdesc_p = dmvgbe->p_rxdesc; 410 else { 411 p_rx_desc->nxtdesc_p = (struct mvgbe_rxdesc *) 412 ((u32) p_rx_desc + MV_RXQ_DESC_ALIGNED_SIZE); 413 p_rx_desc = p_rx_desc->nxtdesc_p; 414 } 415 } 416 dmvgbe->p_rxdesc_curr = dmvgbe->p_rxdesc; 417 } 418 419 static int mvgbe_init(struct eth_device *dev) 420 { 421 struct mvgbe_device *dmvgbe = to_mvgbe(dev); 422 struct mvgbe_registers *regs = dmvgbe->regs; 423 #if (defined (CONFIG_MII) || defined (CONFIG_CMD_MII)) \ 424 && defined (CONFIG_SYS_FAULT_ECHO_LINK_DOWN) 425 int i; 426 #endif 427 /* setup RX rings */ 428 mvgbe_init_rx_desc_ring(dmvgbe); 429 430 /* Clear the ethernet port interrupts */ 431 MVGBE_REG_WR(regs->ic, 0); 432 MVGBE_REG_WR(regs->ice, 0); 433 /* Unmask RX buffer and TX end interrupt */ 434 MVGBE_REG_WR(regs->pim, INT_CAUSE_UNMASK_ALL); 435 /* Unmask phy and link status changes interrupts */ 436 MVGBE_REG_WR(regs->peim, INT_CAUSE_UNMASK_ALL_EXT); 437 438 set_dram_access(regs); 439 port_init_mac_tables(regs); 440 port_uc_addr_set(regs, dmvgbe->dev.enetaddr); 441 442 /* Assign port configuration and command. */ 443 MVGBE_REG_WR(regs->pxc, PRT_CFG_VAL); 444 MVGBE_REG_WR(regs->pxcx, PORT_CFG_EXTEND_VALUE); 445 MVGBE_REG_WR(regs->psc0, PORT_SERIAL_CONTROL_VALUE); 446 447 /* Assign port SDMA configuration */ 448 MVGBE_REG_WR(regs->sdc, PORT_SDMA_CFG_VALUE); 449 MVGBE_REG_WR(regs->tqx[0].qxttbc, QTKNBKT_DEF_VAL); 450 MVGBE_REG_WR(regs->tqx[0].tqxtbc, 451 (QMTBS_DEF_VAL << 16) | QTKNRT_DEF_VAL); 452 /* Turn off the port/RXUQ bandwidth limitation */ 453 MVGBE_REG_WR(regs->pmtu, 0); 454 455 /* Set maximum receive buffer to 9700 bytes */ 456 MVGBE_REG_WR(regs->psc0, MVGBE_MAX_RX_PACKET_9700BYTE 457 | (MVGBE_REG_RD(regs->psc0) & MRU_MASK)); 458 459 /* Enable port initially */ 460 MVGBE_REG_BITS_SET(regs->psc0, MVGBE_SERIAL_PORT_EN); 461 462 /* 463 * Set ethernet MTU for leaky bucket mechanism to 0 - this will 464 * disable the leaky bucket mechanism . 465 */ 466 MVGBE_REG_WR(regs->pmtu, 0); 467 468 /* Assignment of Rx CRDB of given RXUQ */ 469 MVGBE_REG_WR(regs->rxcdp[RXUQ], (u32) dmvgbe->p_rxdesc_curr); 470 /* ensure previous write is done before enabling Rx DMA */ 471 isb(); 472 /* Enable port Rx. */ 473 MVGBE_REG_WR(regs->rqc, (1 << RXUQ)); 474 475 #if (defined(CONFIG_MII) || defined(CONFIG_CMD_MII)) && \ 476 !defined(CONFIG_PHYLIB) && \ 477 defined(CONFIG_SYS_FAULT_ECHO_LINK_DOWN) 478 /* Wait up to 5s for the link status */ 479 for (i = 0; i < 5; i++) { 480 u16 phyadr; 481 482 miiphy_read(dev->name, MV_PHY_ADR_REQUEST, 483 MV_PHY_ADR_REQUEST, &phyadr); 484 /* Return if we get link up */ 485 if (miiphy_link(dev->name, phyadr)) 486 return 0; 487 udelay(1000000); 488 } 489 490 printf("No link on %s\n", dev->name); 491 return -1; 492 #endif 493 return 0; 494 } 495 496 static int mvgbe_halt(struct eth_device *dev) 497 { 498 struct mvgbe_device *dmvgbe = to_mvgbe(dev); 499 struct mvgbe_registers *regs = dmvgbe->regs; 500 501 /* Disable all gigE address decoder */ 502 MVGBE_REG_WR(regs->bare, 0x3f); 503 504 stop_queue(®s->tqc); 505 stop_queue(®s->rqc); 506 507 /* Disable port */ 508 MVGBE_REG_BITS_RESET(regs->psc0, MVGBE_SERIAL_PORT_EN); 509 /* Set port is not reset */ 510 MVGBE_REG_BITS_RESET(regs->psc1, 1 << 4); 511 #ifdef CONFIG_SYS_MII_MODE 512 /* Set MMI interface up */ 513 MVGBE_REG_BITS_RESET(regs->psc1, 1 << 3); 514 #endif 515 /* Disable & mask ethernet port interrupts */ 516 MVGBE_REG_WR(regs->ic, 0); 517 MVGBE_REG_WR(regs->ice, 0); 518 MVGBE_REG_WR(regs->pim, 0); 519 MVGBE_REG_WR(regs->peim, 0); 520 521 return 0; 522 } 523 524 static int mvgbe_write_hwaddr(struct eth_device *dev) 525 { 526 struct mvgbe_device *dmvgbe = to_mvgbe(dev); 527 struct mvgbe_registers *regs = dmvgbe->regs; 528 529 /* Programs net device MAC address after initialization */ 530 port_uc_addr_set(regs, dmvgbe->dev.enetaddr); 531 return 0; 532 } 533 534 static int mvgbe_send(struct eth_device *dev, void *dataptr, int datasize) 535 { 536 struct mvgbe_device *dmvgbe = to_mvgbe(dev); 537 struct mvgbe_registers *regs = dmvgbe->regs; 538 struct mvgbe_txdesc *p_txdesc = dmvgbe->p_txdesc; 539 void *p = (void *)dataptr; 540 u32 cmd_sts; 541 u32 txuq0_reg_addr; 542 543 /* Copy buffer if it's misaligned */ 544 if ((u32) dataptr & 0x07) { 545 if (datasize > PKTSIZE_ALIGN) { 546 printf("Non-aligned data too large (%d)\n", 547 datasize); 548 return -1; 549 } 550 551 memcpy(dmvgbe->p_aligned_txbuf, p, datasize); 552 p = dmvgbe->p_aligned_txbuf; 553 } 554 555 p_txdesc->cmd_sts = MVGBE_ZERO_PADDING | MVGBE_GEN_CRC; 556 p_txdesc->cmd_sts |= MVGBE_TX_FIRST_DESC | MVGBE_TX_LAST_DESC; 557 p_txdesc->cmd_sts |= MVGBE_BUFFER_OWNED_BY_DMA; 558 p_txdesc->cmd_sts |= MVGBE_TX_EN_INTERRUPT; 559 p_txdesc->buf_ptr = (u8 *) p; 560 p_txdesc->byte_cnt = datasize; 561 562 /* Set this tc desc as zeroth TXUQ */ 563 txuq0_reg_addr = (u32)®s->tcqdp[TXUQ]; 564 writel((u32) p_txdesc, txuq0_reg_addr); 565 566 /* ensure tx desc writes above are performed before we start Tx DMA */ 567 isb(); 568 569 /* Apply send command using zeroth TXUQ */ 570 MVGBE_REG_WR(regs->tqc, (1 << TXUQ)); 571 572 /* 573 * wait for packet xmit completion 574 */ 575 cmd_sts = readl(&p_txdesc->cmd_sts); 576 while (cmd_sts & MVGBE_BUFFER_OWNED_BY_DMA) { 577 /* return fail if error is detected */ 578 if ((cmd_sts & (MVGBE_ERROR_SUMMARY | MVGBE_TX_LAST_FRAME)) == 579 (MVGBE_ERROR_SUMMARY | MVGBE_TX_LAST_FRAME) && 580 cmd_sts & (MVGBE_UR_ERROR | MVGBE_RL_ERROR)) { 581 printf("Err..(%s) in xmit packet\n", __FUNCTION__); 582 return -1; 583 } 584 cmd_sts = readl(&p_txdesc->cmd_sts); 585 }; 586 return 0; 587 } 588 589 static int mvgbe_recv(struct eth_device *dev) 590 { 591 struct mvgbe_device *dmvgbe = to_mvgbe(dev); 592 struct mvgbe_rxdesc *p_rxdesc_curr = dmvgbe->p_rxdesc_curr; 593 u32 cmd_sts; 594 u32 timeout = 0; 595 u32 rxdesc_curr_addr; 596 597 /* wait untill rx packet available or timeout */ 598 do { 599 if (timeout < MVGBE_PHY_SMI_TIMEOUT) 600 timeout++; 601 else { 602 debug("%s time out...\n", __FUNCTION__); 603 return -1; 604 } 605 } while (readl(&p_rxdesc_curr->cmd_sts) & MVGBE_BUFFER_OWNED_BY_DMA); 606 607 if (p_rxdesc_curr->byte_cnt != 0) { 608 debug("%s: Received %d byte Packet @ 0x%x (cmd_sts= %08x)\n", 609 __FUNCTION__, (u32) p_rxdesc_curr->byte_cnt, 610 (u32) p_rxdesc_curr->buf_ptr, 611 (u32) p_rxdesc_curr->cmd_sts); 612 } 613 614 /* 615 * In case received a packet without first/last bits on 616 * OR the error summary bit is on, 617 * the packets needs to be dropeed. 618 */ 619 cmd_sts = readl(&p_rxdesc_curr->cmd_sts); 620 621 if ((cmd_sts & 622 (MVGBE_RX_FIRST_DESC | MVGBE_RX_LAST_DESC)) 623 != (MVGBE_RX_FIRST_DESC | MVGBE_RX_LAST_DESC)) { 624 625 printf("Err..(%s) Dropping packet spread on" 626 " multiple descriptors\n", __FUNCTION__); 627 628 } else if (cmd_sts & MVGBE_ERROR_SUMMARY) { 629 630 printf("Err..(%s) Dropping packet with errors\n", 631 __FUNCTION__); 632 633 } else { 634 /* !!! call higher layer processing */ 635 debug("%s: Sending Received packet to" 636 " upper layer (NetReceive)\n", __FUNCTION__); 637 638 /* let the upper layer handle the packet */ 639 NetReceive((p_rxdesc_curr->buf_ptr + RX_BUF_OFFSET), 640 (int)(p_rxdesc_curr->byte_cnt - RX_BUF_OFFSET)); 641 } 642 /* 643 * free these descriptors and point next in the ring 644 */ 645 p_rxdesc_curr->cmd_sts = 646 MVGBE_BUFFER_OWNED_BY_DMA | MVGBE_RX_EN_INTERRUPT; 647 p_rxdesc_curr->buf_size = PKTSIZE_ALIGN; 648 p_rxdesc_curr->byte_cnt = 0; 649 650 rxdesc_curr_addr = (u32)&dmvgbe->p_rxdesc_curr; 651 writel((unsigned)p_rxdesc_curr->nxtdesc_p, rxdesc_curr_addr); 652 653 return 0; 654 } 655 656 #if defined(CONFIG_PHYLIB) 657 int mvgbe_phylib_init(struct eth_device *dev, int phyid) 658 { 659 struct mii_dev *bus; 660 struct phy_device *phydev; 661 int ret; 662 663 bus = mdio_alloc(); 664 if (!bus) { 665 printf("mdio_alloc failed\n"); 666 return -ENOMEM; 667 } 668 bus->read = mvgbe_phy_read; 669 bus->write = mvgbe_phy_write; 670 sprintf(bus->name, dev->name); 671 672 ret = mdio_register(bus); 673 if (ret) { 674 printf("mdio_register failed\n"); 675 free(bus); 676 return -ENOMEM; 677 } 678 679 /* Set phy address of the port */ 680 mvgbe_phy_write(bus, MV_PHY_ADR_REQUEST, 0, MV_PHY_ADR_REQUEST, phyid); 681 682 phydev = phy_connect(bus, phyid, dev, PHY_INTERFACE_MODE_RGMII); 683 if (!phydev) { 684 printf("phy_connect failed\n"); 685 return -ENODEV; 686 } 687 688 phy_config(phydev); 689 phy_startup(phydev); 690 691 return 0; 692 } 693 #endif 694 695 int mvgbe_initialize(bd_t *bis) 696 { 697 struct mvgbe_device *dmvgbe; 698 struct eth_device *dev; 699 int devnum; 700 u8 used_ports[MAX_MVGBE_DEVS] = CONFIG_MVGBE_PORTS; 701 702 for (devnum = 0; devnum < MAX_MVGBE_DEVS; devnum++) { 703 /*skip if port is configured not to use */ 704 if (used_ports[devnum] == 0) 705 continue; 706 707 dmvgbe = malloc(sizeof(struct mvgbe_device)); 708 709 if (!dmvgbe) 710 goto error1; 711 712 memset(dmvgbe, 0, sizeof(struct mvgbe_device)); 713 714 dmvgbe->p_rxdesc = 715 (struct mvgbe_rxdesc *)memalign(PKTALIGN, 716 MV_RXQ_DESC_ALIGNED_SIZE*RINGSZ + 1); 717 718 if (!dmvgbe->p_rxdesc) 719 goto error2; 720 721 dmvgbe->p_rxbuf = (u8 *) memalign(PKTALIGN, 722 RINGSZ*PKTSIZE_ALIGN + 1); 723 724 if (!dmvgbe->p_rxbuf) 725 goto error3; 726 727 dmvgbe->p_aligned_txbuf = memalign(8, PKTSIZE_ALIGN); 728 729 if (!dmvgbe->p_aligned_txbuf) 730 goto error4; 731 732 dmvgbe->p_txdesc = (struct mvgbe_txdesc *) memalign( 733 PKTALIGN, sizeof(struct mvgbe_txdesc) + 1); 734 735 if (!dmvgbe->p_txdesc) { 736 free(dmvgbe->p_aligned_txbuf); 737 error4: 738 free(dmvgbe->p_rxbuf); 739 error3: 740 free(dmvgbe->p_rxdesc); 741 error2: 742 free(dmvgbe); 743 error1: 744 printf("Err.. %s Failed to allocate memory\n", 745 __FUNCTION__); 746 return -1; 747 } 748 749 dev = &dmvgbe->dev; 750 751 /* must be less than sizeof(dev->name) */ 752 sprintf(dev->name, "egiga%d", devnum); 753 754 switch (devnum) { 755 case 0: 756 dmvgbe->regs = (void *)MVGBE0_BASE; 757 break; 758 #if defined(MVGBE1_BASE) 759 case 1: 760 dmvgbe->regs = (void *)MVGBE1_BASE; 761 break; 762 #endif 763 default: /* this should never happen */ 764 printf("Err..(%s) Invalid device number %d\n", 765 __FUNCTION__, devnum); 766 return -1; 767 } 768 769 dev->init = (void *)mvgbe_init; 770 dev->halt = (void *)mvgbe_halt; 771 dev->send = (void *)mvgbe_send; 772 dev->recv = (void *)mvgbe_recv; 773 dev->write_hwaddr = (void *)mvgbe_write_hwaddr; 774 775 eth_register(dev); 776 777 #if defined(CONFIG_PHYLIB) 778 mvgbe_phylib_init(dev, PHY_BASE_ADR + devnum); 779 #elif defined(CONFIG_MII) || defined(CONFIG_CMD_MII) 780 miiphy_register(dev->name, smi_reg_read, smi_reg_write); 781 /* Set phy address of the port */ 782 miiphy_write(dev->name, MV_PHY_ADR_REQUEST, 783 MV_PHY_ADR_REQUEST, PHY_BASE_ADR + devnum); 784 #endif 785 } 786 return 0; 787 } 788