1 /************************************************************************** 2 Intel Pro 1000 for ppcboot/das-u-boot 3 Drivers are port from Intel's Linux driver e1000-4.3.15 4 and from Etherboot pro 1000 driver by mrakes at vivato dot net 5 tested on both gig copper and gig fiber boards 6 ***************************************************************************/ 7 /******************************************************************************* 8 9 10 Copyright(c) 1999 - 2002 Intel Corporation. All rights reserved. 11 12 * SPDX-License-Identifier: GPL-2.0+ 13 14 Contact Information: 15 Linux NICS <linux.nics@intel.com> 16 Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 17 18 *******************************************************************************/ 19 /* 20 * Copyright (C) Archway Digital Solutions. 21 * 22 * written by Chrsitopher Li <cli at arcyway dot com> or <chrisl at gnuchina dot org> 23 * 2/9/2002 24 * 25 * Copyright (C) Linux Networx. 26 * Massive upgrade to work with the new intel gigabit NICs. 27 * <ebiederman at lnxi dot com> 28 * 29 * Copyright 2011 Freescale Semiconductor, Inc. 30 */ 31 32 #include <common.h> 33 #include <dm.h> 34 #include <errno.h> 35 #include <memalign.h> 36 #include <pci.h> 37 #include "e1000.h" 38 39 #define TOUT_LOOP 100000 40 41 #ifdef CONFIG_DM_ETH 42 #define virt_to_bus(devno, v) dm_pci_virt_to_mem(devno, (void *) (v)) 43 #define bus_to_phys(devno, a) dm_pci_mem_to_phys(devno, a) 44 #else 45 #define virt_to_bus(devno, v) pci_virt_to_mem(devno, (void *) (v)) 46 #define bus_to_phys(devno, a) pci_mem_to_phys(devno, a) 47 #endif 48 49 #define E1000_DEFAULT_PCI_PBA 0x00000030 50 #define E1000_DEFAULT_PCIE_PBA 0x000a0026 51 52 /* NIC specific static variables go here */ 53 54 /* Intel i210 needs the DMA descriptor rings aligned to 128b */ 55 #define E1000_BUFFER_ALIGN 128 56 57 /* 58 * TODO(sjg@chromium.org): Even with driver model we share these buffers. 59 * Concurrent receiving on multiple active Ethernet devices will not work. 60 * Normally U-Boot does not support this anyway. To fix it in this driver, 61 * move these buffers and the tx/rx pointers to struct e1000_hw. 62 */ 63 DEFINE_ALIGN_BUFFER(struct e1000_tx_desc, tx_base, 16, E1000_BUFFER_ALIGN); 64 DEFINE_ALIGN_BUFFER(struct e1000_rx_desc, rx_base, 16, E1000_BUFFER_ALIGN); 65 DEFINE_ALIGN_BUFFER(unsigned char, packet, 4096, E1000_BUFFER_ALIGN); 66 67 static int tx_tail; 68 static int rx_tail, rx_last; 69 #ifdef CONFIG_DM_ETH 70 static int num_cards; /* Number of E1000 devices seen so far */ 71 #endif 72 73 static struct pci_device_id e1000_supported[] = { 74 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82542) }, 75 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82543GC_FIBER) }, 76 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82543GC_COPPER) }, 77 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82544EI_COPPER) }, 78 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82544EI_FIBER) }, 79 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82544GC_COPPER) }, 80 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82544GC_LOM) }, 81 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82540EM) }, 82 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82545EM_COPPER) }, 83 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82545GM_COPPER) }, 84 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82546EB_COPPER) }, 85 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82545EM_FIBER) }, 86 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82546EB_FIBER) }, 87 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82546GB_COPPER) }, 88 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82540EM_LOM) }, 89 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82541ER) }, 90 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82541GI_LF) }, 91 /* E1000 PCIe card */ 92 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_COPPER) }, 93 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_FIBER) }, 94 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_SERDES) }, 95 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_QUAD_COPPER) }, 96 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571PT_QUAD_COPPER) }, 97 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_QUAD_FIBER) }, 98 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_QUAD_COPPER_LOWPROFILE) }, 99 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_SERDES_DUAL) }, 100 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_SERDES_QUAD) }, 101 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82572EI_COPPER) }, 102 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82572EI_FIBER) }, 103 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82572EI_SERDES) }, 104 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82572EI) }, 105 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82573E) }, 106 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82573E_IAMT) }, 107 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82573L) }, 108 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82574L) }, 109 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82546GB_QUAD_COPPER_KSP3) }, 110 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80003ES2LAN_COPPER_DPT) }, 111 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80003ES2LAN_SERDES_DPT) }, 112 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80003ES2LAN_COPPER_SPT) }, 113 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80003ES2LAN_SERDES_SPT) }, 114 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_I210_UNPROGRAMMED) }, 115 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_I211_UNPROGRAMMED) }, 116 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_I210_COPPER) }, 117 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_I211_COPPER) }, 118 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_I210_COPPER_FLASHLESS) }, 119 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_I210_SERDES) }, 120 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_I210_SERDES_FLASHLESS) }, 121 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_I210_1000BASEKX) }, 122 123 {} 124 }; 125 126 /* Function forward declarations */ 127 static int e1000_setup_link(struct e1000_hw *hw); 128 static int e1000_setup_fiber_link(struct e1000_hw *hw); 129 static int e1000_setup_copper_link(struct e1000_hw *hw); 130 static int e1000_phy_setup_autoneg(struct e1000_hw *hw); 131 static void e1000_config_collision_dist(struct e1000_hw *hw); 132 static int e1000_config_mac_to_phy(struct e1000_hw *hw); 133 static int e1000_config_fc_after_link_up(struct e1000_hw *hw); 134 static int e1000_check_for_link(struct e1000_hw *hw); 135 static int e1000_wait_autoneg(struct e1000_hw *hw); 136 static int e1000_get_speed_and_duplex(struct e1000_hw *hw, uint16_t * speed, 137 uint16_t * duplex); 138 static int e1000_read_phy_reg(struct e1000_hw *hw, uint32_t reg_addr, 139 uint16_t * phy_data); 140 static int e1000_write_phy_reg(struct e1000_hw *hw, uint32_t reg_addr, 141 uint16_t phy_data); 142 static int32_t e1000_phy_hw_reset(struct e1000_hw *hw); 143 static int e1000_phy_reset(struct e1000_hw *hw); 144 static int e1000_detect_gig_phy(struct e1000_hw *hw); 145 static void e1000_set_media_type(struct e1000_hw *hw); 146 147 static int32_t e1000_swfw_sync_acquire(struct e1000_hw *hw, uint16_t mask); 148 static void e1000_swfw_sync_release(struct e1000_hw *hw, uint16_t mask); 149 static int32_t e1000_check_phy_reset_block(struct e1000_hw *hw); 150 151 #ifndef CONFIG_E1000_NO_NVM 152 static void e1000_put_hw_eeprom_semaphore(struct e1000_hw *hw); 153 static int32_t e1000_get_hw_eeprom_semaphore(struct e1000_hw *hw); 154 static int32_t e1000_read_eeprom(struct e1000_hw *hw, uint16_t offset, 155 uint16_t words, 156 uint16_t *data); 157 /****************************************************************************** 158 * Raises the EEPROM's clock input. 159 * 160 * hw - Struct containing variables accessed by shared code 161 * eecd - EECD's current value 162 *****************************************************************************/ 163 void e1000_raise_ee_clk(struct e1000_hw *hw, uint32_t * eecd) 164 { 165 /* Raise the clock input to the EEPROM (by setting the SK bit), and then 166 * wait 50 microseconds. 167 */ 168 *eecd = *eecd | E1000_EECD_SK; 169 E1000_WRITE_REG(hw, EECD, *eecd); 170 E1000_WRITE_FLUSH(hw); 171 udelay(50); 172 } 173 174 /****************************************************************************** 175 * Lowers the EEPROM's clock input. 176 * 177 * hw - Struct containing variables accessed by shared code 178 * eecd - EECD's current value 179 *****************************************************************************/ 180 void e1000_lower_ee_clk(struct e1000_hw *hw, uint32_t * eecd) 181 { 182 /* Lower the clock input to the EEPROM (by clearing the SK bit), and then 183 * wait 50 microseconds. 184 */ 185 *eecd = *eecd & ~E1000_EECD_SK; 186 E1000_WRITE_REG(hw, EECD, *eecd); 187 E1000_WRITE_FLUSH(hw); 188 udelay(50); 189 } 190 191 /****************************************************************************** 192 * Shift data bits out to the EEPROM. 193 * 194 * hw - Struct containing variables accessed by shared code 195 * data - data to send to the EEPROM 196 * count - number of bits to shift out 197 *****************************************************************************/ 198 static void 199 e1000_shift_out_ee_bits(struct e1000_hw *hw, uint16_t data, uint16_t count) 200 { 201 uint32_t eecd; 202 uint32_t mask; 203 204 /* We need to shift "count" bits out to the EEPROM. So, value in the 205 * "data" parameter will be shifted out to the EEPROM one bit at a time. 206 * In order to do this, "data" must be broken down into bits. 207 */ 208 mask = 0x01 << (count - 1); 209 eecd = E1000_READ_REG(hw, EECD); 210 eecd &= ~(E1000_EECD_DO | E1000_EECD_DI); 211 do { 212 /* A "1" is shifted out to the EEPROM by setting bit "DI" to a "1", 213 * and then raising and then lowering the clock (the SK bit controls 214 * the clock input to the EEPROM). A "0" is shifted out to the EEPROM 215 * by setting "DI" to "0" and then raising and then lowering the clock. 216 */ 217 eecd &= ~E1000_EECD_DI; 218 219 if (data & mask) 220 eecd |= E1000_EECD_DI; 221 222 E1000_WRITE_REG(hw, EECD, eecd); 223 E1000_WRITE_FLUSH(hw); 224 225 udelay(50); 226 227 e1000_raise_ee_clk(hw, &eecd); 228 e1000_lower_ee_clk(hw, &eecd); 229 230 mask = mask >> 1; 231 232 } while (mask); 233 234 /* We leave the "DI" bit set to "0" when we leave this routine. */ 235 eecd &= ~E1000_EECD_DI; 236 E1000_WRITE_REG(hw, EECD, eecd); 237 } 238 239 /****************************************************************************** 240 * Shift data bits in from the EEPROM 241 * 242 * hw - Struct containing variables accessed by shared code 243 *****************************************************************************/ 244 static uint16_t 245 e1000_shift_in_ee_bits(struct e1000_hw *hw, uint16_t count) 246 { 247 uint32_t eecd; 248 uint32_t i; 249 uint16_t data; 250 251 /* In order to read a register from the EEPROM, we need to shift 'count' 252 * bits in from the EEPROM. Bits are "shifted in" by raising the clock 253 * input to the EEPROM (setting the SK bit), and then reading the 254 * value of the "DO" bit. During this "shifting in" process the 255 * "DI" bit should always be clear. 256 */ 257 258 eecd = E1000_READ_REG(hw, EECD); 259 260 eecd &= ~(E1000_EECD_DO | E1000_EECD_DI); 261 data = 0; 262 263 for (i = 0; i < count; i++) { 264 data = data << 1; 265 e1000_raise_ee_clk(hw, &eecd); 266 267 eecd = E1000_READ_REG(hw, EECD); 268 269 eecd &= ~(E1000_EECD_DI); 270 if (eecd & E1000_EECD_DO) 271 data |= 1; 272 273 e1000_lower_ee_clk(hw, &eecd); 274 } 275 276 return data; 277 } 278 279 /****************************************************************************** 280 * Returns EEPROM to a "standby" state 281 * 282 * hw - Struct containing variables accessed by shared code 283 *****************************************************************************/ 284 void e1000_standby_eeprom(struct e1000_hw *hw) 285 { 286 struct e1000_eeprom_info *eeprom = &hw->eeprom; 287 uint32_t eecd; 288 289 eecd = E1000_READ_REG(hw, EECD); 290 291 if (eeprom->type == e1000_eeprom_microwire) { 292 eecd &= ~(E1000_EECD_CS | E1000_EECD_SK); 293 E1000_WRITE_REG(hw, EECD, eecd); 294 E1000_WRITE_FLUSH(hw); 295 udelay(eeprom->delay_usec); 296 297 /* Clock high */ 298 eecd |= E1000_EECD_SK; 299 E1000_WRITE_REG(hw, EECD, eecd); 300 E1000_WRITE_FLUSH(hw); 301 udelay(eeprom->delay_usec); 302 303 /* Select EEPROM */ 304 eecd |= E1000_EECD_CS; 305 E1000_WRITE_REG(hw, EECD, eecd); 306 E1000_WRITE_FLUSH(hw); 307 udelay(eeprom->delay_usec); 308 309 /* Clock low */ 310 eecd &= ~E1000_EECD_SK; 311 E1000_WRITE_REG(hw, EECD, eecd); 312 E1000_WRITE_FLUSH(hw); 313 udelay(eeprom->delay_usec); 314 } else if (eeprom->type == e1000_eeprom_spi) { 315 /* Toggle CS to flush commands */ 316 eecd |= E1000_EECD_CS; 317 E1000_WRITE_REG(hw, EECD, eecd); 318 E1000_WRITE_FLUSH(hw); 319 udelay(eeprom->delay_usec); 320 eecd &= ~E1000_EECD_CS; 321 E1000_WRITE_REG(hw, EECD, eecd); 322 E1000_WRITE_FLUSH(hw); 323 udelay(eeprom->delay_usec); 324 } 325 } 326 327 /*************************************************************************** 328 * Description: Determines if the onboard NVM is FLASH or EEPROM. 329 * 330 * hw - Struct containing variables accessed by shared code 331 ****************************************************************************/ 332 static bool e1000_is_onboard_nvm_eeprom(struct e1000_hw *hw) 333 { 334 uint32_t eecd = 0; 335 336 DEBUGFUNC(); 337 338 if (hw->mac_type == e1000_ich8lan) 339 return false; 340 341 if (hw->mac_type == e1000_82573 || hw->mac_type == e1000_82574) { 342 eecd = E1000_READ_REG(hw, EECD); 343 344 /* Isolate bits 15 & 16 */ 345 eecd = ((eecd >> 15) & 0x03); 346 347 /* If both bits are set, device is Flash type */ 348 if (eecd == 0x03) 349 return false; 350 } 351 return true; 352 } 353 354 /****************************************************************************** 355 * Prepares EEPROM for access 356 * 357 * hw - Struct containing variables accessed by shared code 358 * 359 * Lowers EEPROM clock. Clears input pin. Sets the chip select pin. This 360 * function should be called before issuing a command to the EEPROM. 361 *****************************************************************************/ 362 int32_t e1000_acquire_eeprom(struct e1000_hw *hw) 363 { 364 struct e1000_eeprom_info *eeprom = &hw->eeprom; 365 uint32_t eecd, i = 0; 366 367 DEBUGFUNC(); 368 369 if (e1000_swfw_sync_acquire(hw, E1000_SWFW_EEP_SM)) 370 return -E1000_ERR_SWFW_SYNC; 371 eecd = E1000_READ_REG(hw, EECD); 372 373 if (hw->mac_type != e1000_82573 && hw->mac_type != e1000_82574) { 374 /* Request EEPROM Access */ 375 if (hw->mac_type > e1000_82544) { 376 eecd |= E1000_EECD_REQ; 377 E1000_WRITE_REG(hw, EECD, eecd); 378 eecd = E1000_READ_REG(hw, EECD); 379 while ((!(eecd & E1000_EECD_GNT)) && 380 (i < E1000_EEPROM_GRANT_ATTEMPTS)) { 381 i++; 382 udelay(5); 383 eecd = E1000_READ_REG(hw, EECD); 384 } 385 if (!(eecd & E1000_EECD_GNT)) { 386 eecd &= ~E1000_EECD_REQ; 387 E1000_WRITE_REG(hw, EECD, eecd); 388 DEBUGOUT("Could not acquire EEPROM grant\n"); 389 return -E1000_ERR_EEPROM; 390 } 391 } 392 } 393 394 /* Setup EEPROM for Read/Write */ 395 396 if (eeprom->type == e1000_eeprom_microwire) { 397 /* Clear SK and DI */ 398 eecd &= ~(E1000_EECD_DI | E1000_EECD_SK); 399 E1000_WRITE_REG(hw, EECD, eecd); 400 401 /* Set CS */ 402 eecd |= E1000_EECD_CS; 403 E1000_WRITE_REG(hw, EECD, eecd); 404 } else if (eeprom->type == e1000_eeprom_spi) { 405 /* Clear SK and CS */ 406 eecd &= ~(E1000_EECD_CS | E1000_EECD_SK); 407 E1000_WRITE_REG(hw, EECD, eecd); 408 udelay(1); 409 } 410 411 return E1000_SUCCESS; 412 } 413 414 /****************************************************************************** 415 * Sets up eeprom variables in the hw struct. Must be called after mac_type 416 * is configured. Additionally, if this is ICH8, the flash controller GbE 417 * registers must be mapped, or this will crash. 418 * 419 * hw - Struct containing variables accessed by shared code 420 *****************************************************************************/ 421 static int32_t e1000_init_eeprom_params(struct e1000_hw *hw) 422 { 423 struct e1000_eeprom_info *eeprom = &hw->eeprom; 424 uint32_t eecd; 425 int32_t ret_val = E1000_SUCCESS; 426 uint16_t eeprom_size; 427 428 if (hw->mac_type == e1000_igb) 429 eecd = E1000_READ_REG(hw, I210_EECD); 430 else 431 eecd = E1000_READ_REG(hw, EECD); 432 433 DEBUGFUNC(); 434 435 switch (hw->mac_type) { 436 case e1000_82542_rev2_0: 437 case e1000_82542_rev2_1: 438 case e1000_82543: 439 case e1000_82544: 440 eeprom->type = e1000_eeprom_microwire; 441 eeprom->word_size = 64; 442 eeprom->opcode_bits = 3; 443 eeprom->address_bits = 6; 444 eeprom->delay_usec = 50; 445 eeprom->use_eerd = false; 446 eeprom->use_eewr = false; 447 break; 448 case e1000_82540: 449 case e1000_82545: 450 case e1000_82545_rev_3: 451 case e1000_82546: 452 case e1000_82546_rev_3: 453 eeprom->type = e1000_eeprom_microwire; 454 eeprom->opcode_bits = 3; 455 eeprom->delay_usec = 50; 456 if (eecd & E1000_EECD_SIZE) { 457 eeprom->word_size = 256; 458 eeprom->address_bits = 8; 459 } else { 460 eeprom->word_size = 64; 461 eeprom->address_bits = 6; 462 } 463 eeprom->use_eerd = false; 464 eeprom->use_eewr = false; 465 break; 466 case e1000_82541: 467 case e1000_82541_rev_2: 468 case e1000_82547: 469 case e1000_82547_rev_2: 470 if (eecd & E1000_EECD_TYPE) { 471 eeprom->type = e1000_eeprom_spi; 472 eeprom->opcode_bits = 8; 473 eeprom->delay_usec = 1; 474 if (eecd & E1000_EECD_ADDR_BITS) { 475 eeprom->page_size = 32; 476 eeprom->address_bits = 16; 477 } else { 478 eeprom->page_size = 8; 479 eeprom->address_bits = 8; 480 } 481 } else { 482 eeprom->type = e1000_eeprom_microwire; 483 eeprom->opcode_bits = 3; 484 eeprom->delay_usec = 50; 485 if (eecd & E1000_EECD_ADDR_BITS) { 486 eeprom->word_size = 256; 487 eeprom->address_bits = 8; 488 } else { 489 eeprom->word_size = 64; 490 eeprom->address_bits = 6; 491 } 492 } 493 eeprom->use_eerd = false; 494 eeprom->use_eewr = false; 495 break; 496 case e1000_82571: 497 case e1000_82572: 498 eeprom->type = e1000_eeprom_spi; 499 eeprom->opcode_bits = 8; 500 eeprom->delay_usec = 1; 501 if (eecd & E1000_EECD_ADDR_BITS) { 502 eeprom->page_size = 32; 503 eeprom->address_bits = 16; 504 } else { 505 eeprom->page_size = 8; 506 eeprom->address_bits = 8; 507 } 508 eeprom->use_eerd = false; 509 eeprom->use_eewr = false; 510 break; 511 case e1000_82573: 512 case e1000_82574: 513 eeprom->type = e1000_eeprom_spi; 514 eeprom->opcode_bits = 8; 515 eeprom->delay_usec = 1; 516 if (eecd & E1000_EECD_ADDR_BITS) { 517 eeprom->page_size = 32; 518 eeprom->address_bits = 16; 519 } else { 520 eeprom->page_size = 8; 521 eeprom->address_bits = 8; 522 } 523 if (e1000_is_onboard_nvm_eeprom(hw) == false) { 524 eeprom->use_eerd = true; 525 eeprom->use_eewr = true; 526 527 eeprom->type = e1000_eeprom_flash; 528 eeprom->word_size = 2048; 529 530 /* Ensure that the Autonomous FLASH update bit is cleared due to 531 * Flash update issue on parts which use a FLASH for NVM. */ 532 eecd &= ~E1000_EECD_AUPDEN; 533 E1000_WRITE_REG(hw, EECD, eecd); 534 } 535 break; 536 case e1000_80003es2lan: 537 eeprom->type = e1000_eeprom_spi; 538 eeprom->opcode_bits = 8; 539 eeprom->delay_usec = 1; 540 if (eecd & E1000_EECD_ADDR_BITS) { 541 eeprom->page_size = 32; 542 eeprom->address_bits = 16; 543 } else { 544 eeprom->page_size = 8; 545 eeprom->address_bits = 8; 546 } 547 eeprom->use_eerd = true; 548 eeprom->use_eewr = false; 549 break; 550 case e1000_igb: 551 /* i210 has 4k of iNVM mapped as EEPROM */ 552 eeprom->type = e1000_eeprom_invm; 553 eeprom->opcode_bits = 8; 554 eeprom->delay_usec = 1; 555 eeprom->page_size = 32; 556 eeprom->address_bits = 16; 557 eeprom->use_eerd = true; 558 eeprom->use_eewr = false; 559 break; 560 default: 561 break; 562 } 563 564 if (eeprom->type == e1000_eeprom_spi || 565 eeprom->type == e1000_eeprom_invm) { 566 /* eeprom_size will be an enum [0..8] that maps 567 * to eeprom sizes 128B to 568 * 32KB (incremented by powers of 2). 569 */ 570 if (hw->mac_type <= e1000_82547_rev_2) { 571 /* Set to default value for initial eeprom read. */ 572 eeprom->word_size = 64; 573 ret_val = e1000_read_eeprom(hw, EEPROM_CFG, 1, 574 &eeprom_size); 575 if (ret_val) 576 return ret_val; 577 eeprom_size = (eeprom_size & EEPROM_SIZE_MASK) 578 >> EEPROM_SIZE_SHIFT; 579 /* 256B eeprom size was not supported in earlier 580 * hardware, so we bump eeprom_size up one to 581 * ensure that "1" (which maps to 256B) is never 582 * the result used in the shifting logic below. */ 583 if (eeprom_size) 584 eeprom_size++; 585 } else { 586 eeprom_size = (uint16_t)((eecd & 587 E1000_EECD_SIZE_EX_MASK) >> 588 E1000_EECD_SIZE_EX_SHIFT); 589 } 590 591 eeprom->word_size = 1 << (eeprom_size + EEPROM_WORD_SIZE_SHIFT); 592 } 593 return ret_val; 594 } 595 596 /****************************************************************************** 597 * Polls the status bit (bit 1) of the EERD to determine when the read is done. 598 * 599 * hw - Struct containing variables accessed by shared code 600 *****************************************************************************/ 601 static int32_t 602 e1000_poll_eerd_eewr_done(struct e1000_hw *hw, int eerd) 603 { 604 uint32_t attempts = 100000; 605 uint32_t i, reg = 0; 606 int32_t done = E1000_ERR_EEPROM; 607 608 for (i = 0; i < attempts; i++) { 609 if (eerd == E1000_EEPROM_POLL_READ) { 610 if (hw->mac_type == e1000_igb) 611 reg = E1000_READ_REG(hw, I210_EERD); 612 else 613 reg = E1000_READ_REG(hw, EERD); 614 } else { 615 if (hw->mac_type == e1000_igb) 616 reg = E1000_READ_REG(hw, I210_EEWR); 617 else 618 reg = E1000_READ_REG(hw, EEWR); 619 } 620 621 if (reg & E1000_EEPROM_RW_REG_DONE) { 622 done = E1000_SUCCESS; 623 break; 624 } 625 udelay(5); 626 } 627 628 return done; 629 } 630 631 /****************************************************************************** 632 * Reads a 16 bit word from the EEPROM using the EERD register. 633 * 634 * hw - Struct containing variables accessed by shared code 635 * offset - offset of word in the EEPROM to read 636 * data - word read from the EEPROM 637 * words - number of words to read 638 *****************************************************************************/ 639 static int32_t 640 e1000_read_eeprom_eerd(struct e1000_hw *hw, 641 uint16_t offset, 642 uint16_t words, 643 uint16_t *data) 644 { 645 uint32_t i, eerd = 0; 646 int32_t error = 0; 647 648 for (i = 0; i < words; i++) { 649 eerd = ((offset+i) << E1000_EEPROM_RW_ADDR_SHIFT) + 650 E1000_EEPROM_RW_REG_START; 651 652 if (hw->mac_type == e1000_igb) 653 E1000_WRITE_REG(hw, I210_EERD, eerd); 654 else 655 E1000_WRITE_REG(hw, EERD, eerd); 656 657 error = e1000_poll_eerd_eewr_done(hw, E1000_EEPROM_POLL_READ); 658 659 if (error) 660 break; 661 662 if (hw->mac_type == e1000_igb) { 663 data[i] = (E1000_READ_REG(hw, I210_EERD) >> 664 E1000_EEPROM_RW_REG_DATA); 665 } else { 666 data[i] = (E1000_READ_REG(hw, EERD) >> 667 E1000_EEPROM_RW_REG_DATA); 668 } 669 670 } 671 672 return error; 673 } 674 675 void e1000_release_eeprom(struct e1000_hw *hw) 676 { 677 uint32_t eecd; 678 679 DEBUGFUNC(); 680 681 eecd = E1000_READ_REG(hw, EECD); 682 683 if (hw->eeprom.type == e1000_eeprom_spi) { 684 eecd |= E1000_EECD_CS; /* Pull CS high */ 685 eecd &= ~E1000_EECD_SK; /* Lower SCK */ 686 687 E1000_WRITE_REG(hw, EECD, eecd); 688 689 udelay(hw->eeprom.delay_usec); 690 } else if (hw->eeprom.type == e1000_eeprom_microwire) { 691 /* cleanup eeprom */ 692 693 /* CS on Microwire is active-high */ 694 eecd &= ~(E1000_EECD_CS | E1000_EECD_DI); 695 696 E1000_WRITE_REG(hw, EECD, eecd); 697 698 /* Rising edge of clock */ 699 eecd |= E1000_EECD_SK; 700 E1000_WRITE_REG(hw, EECD, eecd); 701 E1000_WRITE_FLUSH(hw); 702 udelay(hw->eeprom.delay_usec); 703 704 /* Falling edge of clock */ 705 eecd &= ~E1000_EECD_SK; 706 E1000_WRITE_REG(hw, EECD, eecd); 707 E1000_WRITE_FLUSH(hw); 708 udelay(hw->eeprom.delay_usec); 709 } 710 711 /* Stop requesting EEPROM access */ 712 if (hw->mac_type > e1000_82544) { 713 eecd &= ~E1000_EECD_REQ; 714 E1000_WRITE_REG(hw, EECD, eecd); 715 } 716 717 e1000_swfw_sync_release(hw, E1000_SWFW_EEP_SM); 718 } 719 720 /****************************************************************************** 721 * Reads a 16 bit word from the EEPROM. 722 * 723 * hw - Struct containing variables accessed by shared code 724 *****************************************************************************/ 725 static int32_t 726 e1000_spi_eeprom_ready(struct e1000_hw *hw) 727 { 728 uint16_t retry_count = 0; 729 uint8_t spi_stat_reg; 730 731 DEBUGFUNC(); 732 733 /* Read "Status Register" repeatedly until the LSB is cleared. The 734 * EEPROM will signal that the command has been completed by clearing 735 * bit 0 of the internal status register. If it's not cleared within 736 * 5 milliseconds, then error out. 737 */ 738 retry_count = 0; 739 do { 740 e1000_shift_out_ee_bits(hw, EEPROM_RDSR_OPCODE_SPI, 741 hw->eeprom.opcode_bits); 742 spi_stat_reg = (uint8_t)e1000_shift_in_ee_bits(hw, 8); 743 if (!(spi_stat_reg & EEPROM_STATUS_RDY_SPI)) 744 break; 745 746 udelay(5); 747 retry_count += 5; 748 749 e1000_standby_eeprom(hw); 750 } while (retry_count < EEPROM_MAX_RETRY_SPI); 751 752 /* ATMEL SPI write time could vary from 0-20mSec on 3.3V devices (and 753 * only 0-5mSec on 5V devices) 754 */ 755 if (retry_count >= EEPROM_MAX_RETRY_SPI) { 756 DEBUGOUT("SPI EEPROM Status error\n"); 757 return -E1000_ERR_EEPROM; 758 } 759 760 return E1000_SUCCESS; 761 } 762 763 /****************************************************************************** 764 * Reads a 16 bit word from the EEPROM. 765 * 766 * hw - Struct containing variables accessed by shared code 767 * offset - offset of word in the EEPROM to read 768 * data - word read from the EEPROM 769 *****************************************************************************/ 770 static int32_t 771 e1000_read_eeprom(struct e1000_hw *hw, uint16_t offset, 772 uint16_t words, uint16_t *data) 773 { 774 struct e1000_eeprom_info *eeprom = &hw->eeprom; 775 uint32_t i = 0; 776 777 DEBUGFUNC(); 778 779 /* If eeprom is not yet detected, do so now */ 780 if (eeprom->word_size == 0) 781 e1000_init_eeprom_params(hw); 782 783 /* A check for invalid values: offset too large, too many words, 784 * and not enough words. 785 */ 786 if ((offset >= eeprom->word_size) || 787 (words > eeprom->word_size - offset) || 788 (words == 0)) { 789 DEBUGOUT("\"words\" parameter out of bounds." 790 "Words = %d, size = %d\n", offset, eeprom->word_size); 791 return -E1000_ERR_EEPROM; 792 } 793 794 /* EEPROM's that don't use EERD to read require us to bit-bang the SPI 795 * directly. In this case, we need to acquire the EEPROM so that 796 * FW or other port software does not interrupt. 797 */ 798 if (e1000_is_onboard_nvm_eeprom(hw) == true && 799 hw->eeprom.use_eerd == false) { 800 801 /* Prepare the EEPROM for bit-bang reading */ 802 if (e1000_acquire_eeprom(hw) != E1000_SUCCESS) 803 return -E1000_ERR_EEPROM; 804 } 805 806 /* Eerd register EEPROM access requires no eeprom aquire/release */ 807 if (eeprom->use_eerd == true) 808 return e1000_read_eeprom_eerd(hw, offset, words, data); 809 810 /* Set up the SPI or Microwire EEPROM for bit-bang reading. We have 811 * acquired the EEPROM at this point, so any returns should relase it */ 812 if (eeprom->type == e1000_eeprom_spi) { 813 uint16_t word_in; 814 uint8_t read_opcode = EEPROM_READ_OPCODE_SPI; 815 816 if (e1000_spi_eeprom_ready(hw)) { 817 e1000_release_eeprom(hw); 818 return -E1000_ERR_EEPROM; 819 } 820 821 e1000_standby_eeprom(hw); 822 823 /* Some SPI eeproms use the 8th address bit embedded in 824 * the opcode */ 825 if ((eeprom->address_bits == 8) && (offset >= 128)) 826 read_opcode |= EEPROM_A8_OPCODE_SPI; 827 828 /* Send the READ command (opcode + addr) */ 829 e1000_shift_out_ee_bits(hw, read_opcode, eeprom->opcode_bits); 830 e1000_shift_out_ee_bits(hw, (uint16_t)(offset*2), 831 eeprom->address_bits); 832 833 /* Read the data. The address of the eeprom internally 834 * increments with each byte (spi) being read, saving on the 835 * overhead of eeprom setup and tear-down. The address 836 * counter will roll over if reading beyond the size of 837 * the eeprom, thus allowing the entire memory to be read 838 * starting from any offset. */ 839 for (i = 0; i < words; i++) { 840 word_in = e1000_shift_in_ee_bits(hw, 16); 841 data[i] = (word_in >> 8) | (word_in << 8); 842 } 843 } else if (eeprom->type == e1000_eeprom_microwire) { 844 for (i = 0; i < words; i++) { 845 /* Send the READ command (opcode + addr) */ 846 e1000_shift_out_ee_bits(hw, 847 EEPROM_READ_OPCODE_MICROWIRE, 848 eeprom->opcode_bits); 849 e1000_shift_out_ee_bits(hw, (uint16_t)(offset + i), 850 eeprom->address_bits); 851 852 /* Read the data. For microwire, each word requires 853 * the overhead of eeprom setup and tear-down. */ 854 data[i] = e1000_shift_in_ee_bits(hw, 16); 855 e1000_standby_eeprom(hw); 856 } 857 } 858 859 /* End this read operation */ 860 e1000_release_eeprom(hw); 861 862 return E1000_SUCCESS; 863 } 864 865 #ifndef CONFIG_DM_ETH 866 /****************************************************************************** 867 * e1000_write_eeprom_srwr - Write to Shadow Ram using EEWR 868 * @hw: pointer to the HW structure 869 * @offset: offset within the Shadow Ram to be written to 870 * @words: number of words to write 871 * @data: 16 bit word(s) to be written to the Shadow Ram 872 * 873 * Writes data to Shadow Ram at offset using EEWR register. 874 * 875 * If e1000_update_eeprom_checksum_i210 is not called after this function, the 876 * Shadow Ram will most likely contain an invalid checksum. 877 *****************************************************************************/ 878 static int32_t e1000_write_eeprom_srwr(struct e1000_hw *hw, uint16_t offset, 879 uint16_t words, uint16_t *data) 880 { 881 struct e1000_eeprom_info *eeprom = &hw->eeprom; 882 uint32_t i, k, eewr = 0; 883 uint32_t attempts = 100000; 884 int32_t ret_val = 0; 885 886 /* A check for invalid values: offset too large, too many words, 887 * too many words for the offset, and not enough words. 888 */ 889 if ((offset >= eeprom->word_size) || 890 (words > (eeprom->word_size - offset)) || (words == 0)) { 891 DEBUGOUT("nvm parameter(s) out of bounds\n"); 892 ret_val = -E1000_ERR_EEPROM; 893 goto out; 894 } 895 896 for (i = 0; i < words; i++) { 897 eewr = ((offset + i) << E1000_EEPROM_RW_ADDR_SHIFT) 898 | (data[i] << E1000_EEPROM_RW_REG_DATA) | 899 E1000_EEPROM_RW_REG_START; 900 901 E1000_WRITE_REG(hw, I210_EEWR, eewr); 902 903 for (k = 0; k < attempts; k++) { 904 if (E1000_EEPROM_RW_REG_DONE & 905 E1000_READ_REG(hw, I210_EEWR)) { 906 ret_val = 0; 907 break; 908 } 909 udelay(5); 910 } 911 912 if (ret_val) { 913 DEBUGOUT("Shadow RAM write EEWR timed out\n"); 914 break; 915 } 916 } 917 918 out: 919 return ret_val; 920 } 921 922 /****************************************************************************** 923 * e1000_pool_flash_update_done_i210 - Pool FLUDONE status. 924 * @hw: pointer to the HW structure 925 * 926 *****************************************************************************/ 927 static int32_t e1000_pool_flash_update_done_i210(struct e1000_hw *hw) 928 { 929 int32_t ret_val = -E1000_ERR_EEPROM; 930 uint32_t i, reg; 931 932 for (i = 0; i < E1000_FLUDONE_ATTEMPTS; i++) { 933 reg = E1000_READ_REG(hw, EECD); 934 if (reg & E1000_EECD_FLUDONE_I210) { 935 ret_val = 0; 936 break; 937 } 938 udelay(5); 939 } 940 941 return ret_val; 942 } 943 944 /****************************************************************************** 945 * e1000_update_flash_i210 - Commit EEPROM to the flash 946 * @hw: pointer to the HW structure 947 * 948 *****************************************************************************/ 949 static int32_t e1000_update_flash_i210(struct e1000_hw *hw) 950 { 951 int32_t ret_val = 0; 952 uint32_t flup; 953 954 ret_val = e1000_pool_flash_update_done_i210(hw); 955 if (ret_val == -E1000_ERR_EEPROM) { 956 DEBUGOUT("Flash update time out\n"); 957 goto out; 958 } 959 960 flup = E1000_READ_REG(hw, EECD) | E1000_EECD_FLUPD_I210; 961 E1000_WRITE_REG(hw, EECD, flup); 962 963 ret_val = e1000_pool_flash_update_done_i210(hw); 964 if (ret_val) 965 DEBUGOUT("Flash update time out\n"); 966 else 967 DEBUGOUT("Flash update complete\n"); 968 969 out: 970 return ret_val; 971 } 972 973 /****************************************************************************** 974 * e1000_update_eeprom_checksum_i210 - Update EEPROM checksum 975 * @hw: pointer to the HW structure 976 * 977 * Updates the EEPROM checksum by reading/adding each word of the EEPROM 978 * up to the checksum. Then calculates the EEPROM checksum and writes the 979 * value to the EEPROM. Next commit EEPROM data onto the Flash. 980 *****************************************************************************/ 981 static int32_t e1000_update_eeprom_checksum_i210(struct e1000_hw *hw) 982 { 983 int32_t ret_val = 0; 984 uint16_t checksum = 0; 985 uint16_t i, nvm_data; 986 987 /* Read the first word from the EEPROM. If this times out or fails, do 988 * not continue or we could be in for a very long wait while every 989 * EEPROM read fails 990 */ 991 ret_val = e1000_read_eeprom_eerd(hw, 0, 1, &nvm_data); 992 if (ret_val) { 993 DEBUGOUT("EEPROM read failed\n"); 994 goto out; 995 } 996 997 if (!(e1000_get_hw_eeprom_semaphore(hw))) { 998 /* Do not use hw->nvm.ops.write, hw->nvm.ops.read 999 * because we do not want to take the synchronization 1000 * semaphores twice here. 1001 */ 1002 1003 for (i = 0; i < EEPROM_CHECKSUM_REG; i++) { 1004 ret_val = e1000_read_eeprom_eerd(hw, i, 1, &nvm_data); 1005 if (ret_val) { 1006 e1000_put_hw_eeprom_semaphore(hw); 1007 DEBUGOUT("EEPROM Read Error while updating checksum.\n"); 1008 goto out; 1009 } 1010 checksum += nvm_data; 1011 } 1012 checksum = (uint16_t)EEPROM_SUM - checksum; 1013 ret_val = e1000_write_eeprom_srwr(hw, EEPROM_CHECKSUM_REG, 1, 1014 &checksum); 1015 if (ret_val) { 1016 e1000_put_hw_eeprom_semaphore(hw); 1017 DEBUGOUT("EEPROM Write Error while updating checksum.\n"); 1018 goto out; 1019 } 1020 1021 e1000_put_hw_eeprom_semaphore(hw); 1022 1023 ret_val = e1000_update_flash_i210(hw); 1024 } else { 1025 ret_val = -E1000_ERR_SWFW_SYNC; 1026 } 1027 1028 out: 1029 return ret_val; 1030 } 1031 #endif 1032 1033 /****************************************************************************** 1034 * Verifies that the EEPROM has a valid checksum 1035 * 1036 * hw - Struct containing variables accessed by shared code 1037 * 1038 * Reads the first 64 16 bit words of the EEPROM and sums the values read. 1039 * If the the sum of the 64 16 bit words is 0xBABA, the EEPROM's checksum is 1040 * valid. 1041 *****************************************************************************/ 1042 static int e1000_validate_eeprom_checksum(struct e1000_hw *hw) 1043 { 1044 uint16_t i, checksum, checksum_reg, *buf; 1045 1046 DEBUGFUNC(); 1047 1048 /* Allocate a temporary buffer */ 1049 buf = malloc(sizeof(buf[0]) * (EEPROM_CHECKSUM_REG + 1)); 1050 if (!buf) { 1051 E1000_ERR(hw, "Unable to allocate EEPROM buffer!\n"); 1052 return -E1000_ERR_EEPROM; 1053 } 1054 1055 /* Read the EEPROM */ 1056 if (e1000_read_eeprom(hw, 0, EEPROM_CHECKSUM_REG + 1, buf) < 0) { 1057 E1000_ERR(hw, "Unable to read EEPROM!\n"); 1058 return -E1000_ERR_EEPROM; 1059 } 1060 1061 /* Compute the checksum */ 1062 checksum = 0; 1063 for (i = 0; i < EEPROM_CHECKSUM_REG; i++) 1064 checksum += buf[i]; 1065 checksum = ((uint16_t)EEPROM_SUM) - checksum; 1066 checksum_reg = buf[i]; 1067 1068 /* Verify it! */ 1069 if (checksum == checksum_reg) 1070 return 0; 1071 1072 /* Hrm, verification failed, print an error */ 1073 E1000_ERR(hw, "EEPROM checksum is incorrect!\n"); 1074 E1000_ERR(hw, " ...register was 0x%04hx, calculated 0x%04hx\n", 1075 checksum_reg, checksum); 1076 1077 return -E1000_ERR_EEPROM; 1078 } 1079 #endif /* CONFIG_E1000_NO_NVM */ 1080 1081 /***************************************************************************** 1082 * Set PHY to class A mode 1083 * Assumes the following operations will follow to enable the new class mode. 1084 * 1. Do a PHY soft reset 1085 * 2. Restart auto-negotiation or force link. 1086 * 1087 * hw - Struct containing variables accessed by shared code 1088 ****************************************************************************/ 1089 static int32_t 1090 e1000_set_phy_mode(struct e1000_hw *hw) 1091 { 1092 #ifndef CONFIG_E1000_NO_NVM 1093 int32_t ret_val; 1094 uint16_t eeprom_data; 1095 1096 DEBUGFUNC(); 1097 1098 if ((hw->mac_type == e1000_82545_rev_3) && 1099 (hw->media_type == e1000_media_type_copper)) { 1100 ret_val = e1000_read_eeprom(hw, EEPROM_PHY_CLASS_WORD, 1101 1, &eeprom_data); 1102 if (ret_val) 1103 return ret_val; 1104 1105 if ((eeprom_data != EEPROM_RESERVED_WORD) && 1106 (eeprom_data & EEPROM_PHY_CLASS_A)) { 1107 ret_val = e1000_write_phy_reg(hw, 1108 M88E1000_PHY_PAGE_SELECT, 0x000B); 1109 if (ret_val) 1110 return ret_val; 1111 ret_val = e1000_write_phy_reg(hw, 1112 M88E1000_PHY_GEN_CONTROL, 0x8104); 1113 if (ret_val) 1114 return ret_val; 1115 1116 hw->phy_reset_disable = false; 1117 } 1118 } 1119 #endif 1120 return E1000_SUCCESS; 1121 } 1122 1123 #ifndef CONFIG_E1000_NO_NVM 1124 /*************************************************************************** 1125 * 1126 * Obtaining software semaphore bit (SMBI) before resetting PHY. 1127 * 1128 * hw: Struct containing variables accessed by shared code 1129 * 1130 * returns: - E1000_ERR_RESET if fail to obtain semaphore. 1131 * E1000_SUCCESS at any other case. 1132 * 1133 ***************************************************************************/ 1134 static int32_t 1135 e1000_get_software_semaphore(struct e1000_hw *hw) 1136 { 1137 int32_t timeout = hw->eeprom.word_size + 1; 1138 uint32_t swsm; 1139 1140 DEBUGFUNC(); 1141 1142 if (hw->mac_type != e1000_80003es2lan && hw->mac_type != e1000_igb) 1143 return E1000_SUCCESS; 1144 1145 while (timeout) { 1146 swsm = E1000_READ_REG(hw, SWSM); 1147 /* If SMBI bit cleared, it is now set and we hold 1148 * the semaphore */ 1149 if (!(swsm & E1000_SWSM_SMBI)) 1150 break; 1151 mdelay(1); 1152 timeout--; 1153 } 1154 1155 if (!timeout) { 1156 DEBUGOUT("Driver can't access device - SMBI bit is set.\n"); 1157 return -E1000_ERR_RESET; 1158 } 1159 1160 return E1000_SUCCESS; 1161 } 1162 #endif 1163 1164 /*************************************************************************** 1165 * This function clears HW semaphore bits. 1166 * 1167 * hw: Struct containing variables accessed by shared code 1168 * 1169 * returns: - None. 1170 * 1171 ***************************************************************************/ 1172 static void 1173 e1000_put_hw_eeprom_semaphore(struct e1000_hw *hw) 1174 { 1175 #ifndef CONFIG_E1000_NO_NVM 1176 uint32_t swsm; 1177 1178 DEBUGFUNC(); 1179 1180 if (!hw->eeprom_semaphore_present) 1181 return; 1182 1183 swsm = E1000_READ_REG(hw, SWSM); 1184 if (hw->mac_type == e1000_80003es2lan || hw->mac_type == e1000_igb) { 1185 /* Release both semaphores. */ 1186 swsm &= ~(E1000_SWSM_SMBI | E1000_SWSM_SWESMBI); 1187 } else 1188 swsm &= ~(E1000_SWSM_SWESMBI); 1189 E1000_WRITE_REG(hw, SWSM, swsm); 1190 #endif 1191 } 1192 1193 /*************************************************************************** 1194 * 1195 * Using the combination of SMBI and SWESMBI semaphore bits when resetting 1196 * adapter or Eeprom access. 1197 * 1198 * hw: Struct containing variables accessed by shared code 1199 * 1200 * returns: - E1000_ERR_EEPROM if fail to access EEPROM. 1201 * E1000_SUCCESS at any other case. 1202 * 1203 ***************************************************************************/ 1204 static int32_t 1205 e1000_get_hw_eeprom_semaphore(struct e1000_hw *hw) 1206 { 1207 #ifndef CONFIG_E1000_NO_NVM 1208 int32_t timeout; 1209 uint32_t swsm; 1210 1211 DEBUGFUNC(); 1212 1213 if (!hw->eeprom_semaphore_present) 1214 return E1000_SUCCESS; 1215 1216 if (hw->mac_type == e1000_80003es2lan || hw->mac_type == e1000_igb) { 1217 /* Get the SW semaphore. */ 1218 if (e1000_get_software_semaphore(hw) != E1000_SUCCESS) 1219 return -E1000_ERR_EEPROM; 1220 } 1221 1222 /* Get the FW semaphore. */ 1223 timeout = hw->eeprom.word_size + 1; 1224 while (timeout) { 1225 swsm = E1000_READ_REG(hw, SWSM); 1226 swsm |= E1000_SWSM_SWESMBI; 1227 E1000_WRITE_REG(hw, SWSM, swsm); 1228 /* if we managed to set the bit we got the semaphore. */ 1229 swsm = E1000_READ_REG(hw, SWSM); 1230 if (swsm & E1000_SWSM_SWESMBI) 1231 break; 1232 1233 udelay(50); 1234 timeout--; 1235 } 1236 1237 if (!timeout) { 1238 /* Release semaphores */ 1239 e1000_put_hw_eeprom_semaphore(hw); 1240 DEBUGOUT("Driver can't access the Eeprom - " 1241 "SWESMBI bit is set.\n"); 1242 return -E1000_ERR_EEPROM; 1243 } 1244 #endif 1245 return E1000_SUCCESS; 1246 } 1247 1248 /* Take ownership of the PHY */ 1249 static int32_t 1250 e1000_swfw_sync_acquire(struct e1000_hw *hw, uint16_t mask) 1251 { 1252 uint32_t swfw_sync = 0; 1253 uint32_t swmask = mask; 1254 uint32_t fwmask = mask << 16; 1255 int32_t timeout = 200; 1256 1257 DEBUGFUNC(); 1258 while (timeout) { 1259 if (e1000_get_hw_eeprom_semaphore(hw)) 1260 return -E1000_ERR_SWFW_SYNC; 1261 1262 swfw_sync = E1000_READ_REG(hw, SW_FW_SYNC); 1263 if (!(swfw_sync & (fwmask | swmask))) 1264 break; 1265 1266 /* firmware currently using resource (fwmask) */ 1267 /* or other software thread currently using resource (swmask) */ 1268 e1000_put_hw_eeprom_semaphore(hw); 1269 mdelay(5); 1270 timeout--; 1271 } 1272 1273 if (!timeout) { 1274 DEBUGOUT("Driver can't access resource, SW_FW_SYNC timeout.\n"); 1275 return -E1000_ERR_SWFW_SYNC; 1276 } 1277 1278 swfw_sync |= swmask; 1279 E1000_WRITE_REG(hw, SW_FW_SYNC, swfw_sync); 1280 1281 e1000_put_hw_eeprom_semaphore(hw); 1282 return E1000_SUCCESS; 1283 } 1284 1285 static void e1000_swfw_sync_release(struct e1000_hw *hw, uint16_t mask) 1286 { 1287 uint32_t swfw_sync = 0; 1288 1289 DEBUGFUNC(); 1290 while (e1000_get_hw_eeprom_semaphore(hw)) 1291 ; /* Empty */ 1292 1293 swfw_sync = E1000_READ_REG(hw, SW_FW_SYNC); 1294 swfw_sync &= ~mask; 1295 E1000_WRITE_REG(hw, SW_FW_SYNC, swfw_sync); 1296 1297 e1000_put_hw_eeprom_semaphore(hw); 1298 } 1299 1300 static bool e1000_is_second_port(struct e1000_hw *hw) 1301 { 1302 switch (hw->mac_type) { 1303 case e1000_80003es2lan: 1304 case e1000_82546: 1305 case e1000_82571: 1306 if (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1) 1307 return true; 1308 /* Fallthrough */ 1309 default: 1310 return false; 1311 } 1312 } 1313 1314 #ifndef CONFIG_E1000_NO_NVM 1315 /****************************************************************************** 1316 * Reads the adapter's MAC address from the EEPROM 1317 * 1318 * hw - Struct containing variables accessed by shared code 1319 * enetaddr - buffering where the MAC address will be stored 1320 *****************************************************************************/ 1321 static int e1000_read_mac_addr_from_eeprom(struct e1000_hw *hw, 1322 unsigned char enetaddr[6]) 1323 { 1324 uint16_t offset; 1325 uint16_t eeprom_data; 1326 int i; 1327 1328 for (i = 0; i < NODE_ADDRESS_SIZE; i += 2) { 1329 offset = i >> 1; 1330 if (e1000_read_eeprom(hw, offset, 1, &eeprom_data) < 0) { 1331 DEBUGOUT("EEPROM Read Error\n"); 1332 return -E1000_ERR_EEPROM; 1333 } 1334 enetaddr[i] = eeprom_data & 0xff; 1335 enetaddr[i + 1] = (eeprom_data >> 8) & 0xff; 1336 } 1337 1338 return 0; 1339 } 1340 1341 /****************************************************************************** 1342 * Reads the adapter's MAC address from the RAL/RAH registers 1343 * 1344 * hw - Struct containing variables accessed by shared code 1345 * enetaddr - buffering where the MAC address will be stored 1346 *****************************************************************************/ 1347 static int e1000_read_mac_addr_from_regs(struct e1000_hw *hw, 1348 unsigned char enetaddr[6]) 1349 { 1350 uint16_t offset, tmp; 1351 uint32_t reg_data = 0; 1352 int i; 1353 1354 if (hw->mac_type != e1000_igb) 1355 return -E1000_ERR_MAC_TYPE; 1356 1357 for (i = 0; i < NODE_ADDRESS_SIZE; i += 2) { 1358 offset = i >> 1; 1359 1360 if (offset == 0) 1361 reg_data = E1000_READ_REG_ARRAY(hw, RA, 0); 1362 else if (offset == 1) 1363 reg_data >>= 16; 1364 else if (offset == 2) 1365 reg_data = E1000_READ_REG_ARRAY(hw, RA, 1); 1366 tmp = reg_data & 0xffff; 1367 1368 enetaddr[i] = tmp & 0xff; 1369 enetaddr[i + 1] = (tmp >> 8) & 0xff; 1370 } 1371 1372 return 0; 1373 } 1374 1375 /****************************************************************************** 1376 * Reads the adapter's MAC address from the EEPROM and inverts the LSB for the 1377 * second function of dual function devices 1378 * 1379 * hw - Struct containing variables accessed by shared code 1380 * enetaddr - buffering where the MAC address will be stored 1381 *****************************************************************************/ 1382 static int e1000_read_mac_addr(struct e1000_hw *hw, unsigned char enetaddr[6]) 1383 { 1384 int ret_val; 1385 1386 if (hw->mac_type == e1000_igb) { 1387 /* i210 preloads MAC address into RAL/RAH registers */ 1388 ret_val = e1000_read_mac_addr_from_regs(hw, enetaddr); 1389 } else { 1390 ret_val = e1000_read_mac_addr_from_eeprom(hw, enetaddr); 1391 } 1392 if (ret_val) 1393 return ret_val; 1394 1395 /* Invert the last bit if this is the second device */ 1396 if (e1000_is_second_port(hw)) 1397 enetaddr[5] ^= 1; 1398 1399 return 0; 1400 } 1401 #endif 1402 1403 /****************************************************************************** 1404 * Initializes receive address filters. 1405 * 1406 * hw - Struct containing variables accessed by shared code 1407 * 1408 * Places the MAC address in receive address register 0 and clears the rest 1409 * of the receive addresss registers. Clears the multicast table. Assumes 1410 * the receiver is in reset when the routine is called. 1411 *****************************************************************************/ 1412 static void 1413 e1000_init_rx_addrs(struct e1000_hw *hw, unsigned char enetaddr[6]) 1414 { 1415 uint32_t i; 1416 uint32_t addr_low; 1417 uint32_t addr_high; 1418 1419 DEBUGFUNC(); 1420 1421 /* Setup the receive address. */ 1422 DEBUGOUT("Programming MAC Address into RAR[0]\n"); 1423 addr_low = (enetaddr[0] | 1424 (enetaddr[1] << 8) | 1425 (enetaddr[2] << 16) | (enetaddr[3] << 24)); 1426 1427 addr_high = (enetaddr[4] | (enetaddr[5] << 8) | E1000_RAH_AV); 1428 1429 E1000_WRITE_REG_ARRAY(hw, RA, 0, addr_low); 1430 E1000_WRITE_REG_ARRAY(hw, RA, 1, addr_high); 1431 1432 /* Zero out the other 15 receive addresses. */ 1433 DEBUGOUT("Clearing RAR[1-15]\n"); 1434 for (i = 1; i < E1000_RAR_ENTRIES; i++) { 1435 E1000_WRITE_REG_ARRAY(hw, RA, (i << 1), 0); 1436 E1000_WRITE_REG_ARRAY(hw, RA, ((i << 1) + 1), 0); 1437 } 1438 } 1439 1440 /****************************************************************************** 1441 * Clears the VLAN filer table 1442 * 1443 * hw - Struct containing variables accessed by shared code 1444 *****************************************************************************/ 1445 static void 1446 e1000_clear_vfta(struct e1000_hw *hw) 1447 { 1448 uint32_t offset; 1449 1450 for (offset = 0; offset < E1000_VLAN_FILTER_TBL_SIZE; offset++) 1451 E1000_WRITE_REG_ARRAY(hw, VFTA, offset, 0); 1452 } 1453 1454 /****************************************************************************** 1455 * Set the mac type member in the hw struct. 1456 * 1457 * hw - Struct containing variables accessed by shared code 1458 *****************************************************************************/ 1459 int32_t 1460 e1000_set_mac_type(struct e1000_hw *hw) 1461 { 1462 DEBUGFUNC(); 1463 1464 switch (hw->device_id) { 1465 case E1000_DEV_ID_82542: 1466 switch (hw->revision_id) { 1467 case E1000_82542_2_0_REV_ID: 1468 hw->mac_type = e1000_82542_rev2_0; 1469 break; 1470 case E1000_82542_2_1_REV_ID: 1471 hw->mac_type = e1000_82542_rev2_1; 1472 break; 1473 default: 1474 /* Invalid 82542 revision ID */ 1475 return -E1000_ERR_MAC_TYPE; 1476 } 1477 break; 1478 case E1000_DEV_ID_82543GC_FIBER: 1479 case E1000_DEV_ID_82543GC_COPPER: 1480 hw->mac_type = e1000_82543; 1481 break; 1482 case E1000_DEV_ID_82544EI_COPPER: 1483 case E1000_DEV_ID_82544EI_FIBER: 1484 case E1000_DEV_ID_82544GC_COPPER: 1485 case E1000_DEV_ID_82544GC_LOM: 1486 hw->mac_type = e1000_82544; 1487 break; 1488 case E1000_DEV_ID_82540EM: 1489 case E1000_DEV_ID_82540EM_LOM: 1490 case E1000_DEV_ID_82540EP: 1491 case E1000_DEV_ID_82540EP_LOM: 1492 case E1000_DEV_ID_82540EP_LP: 1493 hw->mac_type = e1000_82540; 1494 break; 1495 case E1000_DEV_ID_82545EM_COPPER: 1496 case E1000_DEV_ID_82545EM_FIBER: 1497 hw->mac_type = e1000_82545; 1498 break; 1499 case E1000_DEV_ID_82545GM_COPPER: 1500 case E1000_DEV_ID_82545GM_FIBER: 1501 case E1000_DEV_ID_82545GM_SERDES: 1502 hw->mac_type = e1000_82545_rev_3; 1503 break; 1504 case E1000_DEV_ID_82546EB_COPPER: 1505 case E1000_DEV_ID_82546EB_FIBER: 1506 case E1000_DEV_ID_82546EB_QUAD_COPPER: 1507 hw->mac_type = e1000_82546; 1508 break; 1509 case E1000_DEV_ID_82546GB_COPPER: 1510 case E1000_DEV_ID_82546GB_FIBER: 1511 case E1000_DEV_ID_82546GB_SERDES: 1512 case E1000_DEV_ID_82546GB_PCIE: 1513 case E1000_DEV_ID_82546GB_QUAD_COPPER: 1514 case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3: 1515 hw->mac_type = e1000_82546_rev_3; 1516 break; 1517 case E1000_DEV_ID_82541EI: 1518 case E1000_DEV_ID_82541EI_MOBILE: 1519 case E1000_DEV_ID_82541ER_LOM: 1520 hw->mac_type = e1000_82541; 1521 break; 1522 case E1000_DEV_ID_82541ER: 1523 case E1000_DEV_ID_82541GI: 1524 case E1000_DEV_ID_82541GI_LF: 1525 case E1000_DEV_ID_82541GI_MOBILE: 1526 hw->mac_type = e1000_82541_rev_2; 1527 break; 1528 case E1000_DEV_ID_82547EI: 1529 case E1000_DEV_ID_82547EI_MOBILE: 1530 hw->mac_type = e1000_82547; 1531 break; 1532 case E1000_DEV_ID_82547GI: 1533 hw->mac_type = e1000_82547_rev_2; 1534 break; 1535 case E1000_DEV_ID_82571EB_COPPER: 1536 case E1000_DEV_ID_82571EB_FIBER: 1537 case E1000_DEV_ID_82571EB_SERDES: 1538 case E1000_DEV_ID_82571EB_SERDES_DUAL: 1539 case E1000_DEV_ID_82571EB_SERDES_QUAD: 1540 case E1000_DEV_ID_82571EB_QUAD_COPPER: 1541 case E1000_DEV_ID_82571PT_QUAD_COPPER: 1542 case E1000_DEV_ID_82571EB_QUAD_FIBER: 1543 case E1000_DEV_ID_82571EB_QUAD_COPPER_LOWPROFILE: 1544 hw->mac_type = e1000_82571; 1545 break; 1546 case E1000_DEV_ID_82572EI_COPPER: 1547 case E1000_DEV_ID_82572EI_FIBER: 1548 case E1000_DEV_ID_82572EI_SERDES: 1549 case E1000_DEV_ID_82572EI: 1550 hw->mac_type = e1000_82572; 1551 break; 1552 case E1000_DEV_ID_82573E: 1553 case E1000_DEV_ID_82573E_IAMT: 1554 case E1000_DEV_ID_82573L: 1555 hw->mac_type = e1000_82573; 1556 break; 1557 case E1000_DEV_ID_82574L: 1558 hw->mac_type = e1000_82574; 1559 break; 1560 case E1000_DEV_ID_80003ES2LAN_COPPER_SPT: 1561 case E1000_DEV_ID_80003ES2LAN_SERDES_SPT: 1562 case E1000_DEV_ID_80003ES2LAN_COPPER_DPT: 1563 case E1000_DEV_ID_80003ES2LAN_SERDES_DPT: 1564 hw->mac_type = e1000_80003es2lan; 1565 break; 1566 case E1000_DEV_ID_ICH8_IGP_M_AMT: 1567 case E1000_DEV_ID_ICH8_IGP_AMT: 1568 case E1000_DEV_ID_ICH8_IGP_C: 1569 case E1000_DEV_ID_ICH8_IFE: 1570 case E1000_DEV_ID_ICH8_IFE_GT: 1571 case E1000_DEV_ID_ICH8_IFE_G: 1572 case E1000_DEV_ID_ICH8_IGP_M: 1573 hw->mac_type = e1000_ich8lan; 1574 break; 1575 case PCI_DEVICE_ID_INTEL_I210_UNPROGRAMMED: 1576 case PCI_DEVICE_ID_INTEL_I211_UNPROGRAMMED: 1577 case PCI_DEVICE_ID_INTEL_I210_COPPER: 1578 case PCI_DEVICE_ID_INTEL_I211_COPPER: 1579 case PCI_DEVICE_ID_INTEL_I210_COPPER_FLASHLESS: 1580 case PCI_DEVICE_ID_INTEL_I210_SERDES: 1581 case PCI_DEVICE_ID_INTEL_I210_SERDES_FLASHLESS: 1582 case PCI_DEVICE_ID_INTEL_I210_1000BASEKX: 1583 hw->mac_type = e1000_igb; 1584 break; 1585 default: 1586 /* Should never have loaded on this device */ 1587 return -E1000_ERR_MAC_TYPE; 1588 } 1589 return E1000_SUCCESS; 1590 } 1591 1592 /****************************************************************************** 1593 * Reset the transmit and receive units; mask and clear all interrupts. 1594 * 1595 * hw - Struct containing variables accessed by shared code 1596 *****************************************************************************/ 1597 void 1598 e1000_reset_hw(struct e1000_hw *hw) 1599 { 1600 uint32_t ctrl; 1601 uint32_t ctrl_ext; 1602 uint32_t manc; 1603 uint32_t pba = 0; 1604 uint32_t reg; 1605 1606 DEBUGFUNC(); 1607 1608 /* get the correct pba value for both PCI and PCIe*/ 1609 if (hw->mac_type < e1000_82571) 1610 pba = E1000_DEFAULT_PCI_PBA; 1611 else 1612 pba = E1000_DEFAULT_PCIE_PBA; 1613 1614 /* For 82542 (rev 2.0), disable MWI before issuing a device reset */ 1615 if (hw->mac_type == e1000_82542_rev2_0) { 1616 DEBUGOUT("Disabling MWI on 82542 rev 2.0\n"); 1617 #ifdef CONFIG_DM_ETH 1618 dm_pci_write_config16(hw->pdev, PCI_COMMAND, 1619 hw->pci_cmd_word & ~PCI_COMMAND_INVALIDATE); 1620 #else 1621 pci_write_config_word(hw->pdev, PCI_COMMAND, 1622 hw->pci_cmd_word & ~PCI_COMMAND_INVALIDATE); 1623 #endif 1624 } 1625 1626 /* Clear interrupt mask to stop board from generating interrupts */ 1627 DEBUGOUT("Masking off all interrupts\n"); 1628 if (hw->mac_type == e1000_igb) 1629 E1000_WRITE_REG(hw, I210_IAM, 0); 1630 E1000_WRITE_REG(hw, IMC, 0xffffffff); 1631 1632 /* Disable the Transmit and Receive units. Then delay to allow 1633 * any pending transactions to complete before we hit the MAC with 1634 * the global reset. 1635 */ 1636 E1000_WRITE_REG(hw, RCTL, 0); 1637 E1000_WRITE_REG(hw, TCTL, E1000_TCTL_PSP); 1638 E1000_WRITE_FLUSH(hw); 1639 1640 /* The tbi_compatibility_on Flag must be cleared when Rctl is cleared. */ 1641 hw->tbi_compatibility_on = false; 1642 1643 /* Delay to allow any outstanding PCI transactions to complete before 1644 * resetting the device 1645 */ 1646 mdelay(10); 1647 1648 /* Issue a global reset to the MAC. This will reset the chip's 1649 * transmit, receive, DMA, and link units. It will not effect 1650 * the current PCI configuration. The global reset bit is self- 1651 * clearing, and should clear within a microsecond. 1652 */ 1653 DEBUGOUT("Issuing a global reset to MAC\n"); 1654 ctrl = E1000_READ_REG(hw, CTRL); 1655 1656 E1000_WRITE_REG(hw, CTRL, (ctrl | E1000_CTRL_RST)); 1657 1658 /* Force a reload from the EEPROM if necessary */ 1659 if (hw->mac_type == e1000_igb) { 1660 mdelay(20); 1661 reg = E1000_READ_REG(hw, STATUS); 1662 if (reg & E1000_STATUS_PF_RST_DONE) 1663 DEBUGOUT("PF OK\n"); 1664 reg = E1000_READ_REG(hw, I210_EECD); 1665 if (reg & E1000_EECD_AUTO_RD) 1666 DEBUGOUT("EEC OK\n"); 1667 } else if (hw->mac_type < e1000_82540) { 1668 /* Wait for reset to complete */ 1669 udelay(10); 1670 ctrl_ext = E1000_READ_REG(hw, CTRL_EXT); 1671 ctrl_ext |= E1000_CTRL_EXT_EE_RST; 1672 E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext); 1673 E1000_WRITE_FLUSH(hw); 1674 /* Wait for EEPROM reload */ 1675 mdelay(2); 1676 } else { 1677 /* Wait for EEPROM reload (it happens automatically) */ 1678 mdelay(4); 1679 /* Dissable HW ARPs on ASF enabled adapters */ 1680 manc = E1000_READ_REG(hw, MANC); 1681 manc &= ~(E1000_MANC_ARP_EN); 1682 E1000_WRITE_REG(hw, MANC, manc); 1683 } 1684 1685 /* Clear interrupt mask to stop board from generating interrupts */ 1686 DEBUGOUT("Masking off all interrupts\n"); 1687 if (hw->mac_type == e1000_igb) 1688 E1000_WRITE_REG(hw, I210_IAM, 0); 1689 E1000_WRITE_REG(hw, IMC, 0xffffffff); 1690 1691 /* Clear any pending interrupt events. */ 1692 E1000_READ_REG(hw, ICR); 1693 1694 /* If MWI was previously enabled, reenable it. */ 1695 if (hw->mac_type == e1000_82542_rev2_0) { 1696 #ifdef CONFIG_DM_ETH 1697 dm_pci_write_config16(hw->pdev, PCI_COMMAND, hw->pci_cmd_word); 1698 #else 1699 pci_write_config_word(hw->pdev, PCI_COMMAND, hw->pci_cmd_word); 1700 #endif 1701 } 1702 if (hw->mac_type != e1000_igb) 1703 E1000_WRITE_REG(hw, PBA, pba); 1704 } 1705 1706 /****************************************************************************** 1707 * 1708 * Initialize a number of hardware-dependent bits 1709 * 1710 * hw: Struct containing variables accessed by shared code 1711 * 1712 * This function contains hardware limitation workarounds for PCI-E adapters 1713 * 1714 *****************************************************************************/ 1715 static void 1716 e1000_initialize_hardware_bits(struct e1000_hw *hw) 1717 { 1718 if ((hw->mac_type >= e1000_82571) && 1719 (!hw->initialize_hw_bits_disable)) { 1720 /* Settings common to all PCI-express silicon */ 1721 uint32_t reg_ctrl, reg_ctrl_ext; 1722 uint32_t reg_tarc0, reg_tarc1; 1723 uint32_t reg_tctl; 1724 uint32_t reg_txdctl, reg_txdctl1; 1725 1726 /* link autonegotiation/sync workarounds */ 1727 reg_tarc0 = E1000_READ_REG(hw, TARC0); 1728 reg_tarc0 &= ~((1 << 30)|(1 << 29)|(1 << 28)|(1 << 27)); 1729 1730 /* Enable not-done TX descriptor counting */ 1731 reg_txdctl = E1000_READ_REG(hw, TXDCTL); 1732 reg_txdctl |= E1000_TXDCTL_COUNT_DESC; 1733 E1000_WRITE_REG(hw, TXDCTL, reg_txdctl); 1734 1735 reg_txdctl1 = E1000_READ_REG(hw, TXDCTL1); 1736 reg_txdctl1 |= E1000_TXDCTL_COUNT_DESC; 1737 E1000_WRITE_REG(hw, TXDCTL1, reg_txdctl1); 1738 1739 1740 switch (hw->mac_type) { 1741 case e1000_igb: /* IGB is cool */ 1742 return; 1743 case e1000_82571: 1744 case e1000_82572: 1745 /* Clear PHY TX compatible mode bits */ 1746 reg_tarc1 = E1000_READ_REG(hw, TARC1); 1747 reg_tarc1 &= ~((1 << 30)|(1 << 29)); 1748 1749 /* link autonegotiation/sync workarounds */ 1750 reg_tarc0 |= ((1 << 26)|(1 << 25)|(1 << 24)|(1 << 23)); 1751 1752 /* TX ring control fixes */ 1753 reg_tarc1 |= ((1 << 26)|(1 << 25)|(1 << 24)); 1754 1755 /* Multiple read bit is reversed polarity */ 1756 reg_tctl = E1000_READ_REG(hw, TCTL); 1757 if (reg_tctl & E1000_TCTL_MULR) 1758 reg_tarc1 &= ~(1 << 28); 1759 else 1760 reg_tarc1 |= (1 << 28); 1761 1762 E1000_WRITE_REG(hw, TARC1, reg_tarc1); 1763 break; 1764 case e1000_82573: 1765 case e1000_82574: 1766 reg_ctrl_ext = E1000_READ_REG(hw, CTRL_EXT); 1767 reg_ctrl_ext &= ~(1 << 23); 1768 reg_ctrl_ext |= (1 << 22); 1769 1770 /* TX byte count fix */ 1771 reg_ctrl = E1000_READ_REG(hw, CTRL); 1772 reg_ctrl &= ~(1 << 29); 1773 1774 E1000_WRITE_REG(hw, CTRL_EXT, reg_ctrl_ext); 1775 E1000_WRITE_REG(hw, CTRL, reg_ctrl); 1776 break; 1777 case e1000_80003es2lan: 1778 /* improve small packet performace for fiber/serdes */ 1779 if ((hw->media_type == e1000_media_type_fiber) 1780 || (hw->media_type == 1781 e1000_media_type_internal_serdes)) { 1782 reg_tarc0 &= ~(1 << 20); 1783 } 1784 1785 /* Multiple read bit is reversed polarity */ 1786 reg_tctl = E1000_READ_REG(hw, TCTL); 1787 reg_tarc1 = E1000_READ_REG(hw, TARC1); 1788 if (reg_tctl & E1000_TCTL_MULR) 1789 reg_tarc1 &= ~(1 << 28); 1790 else 1791 reg_tarc1 |= (1 << 28); 1792 1793 E1000_WRITE_REG(hw, TARC1, reg_tarc1); 1794 break; 1795 case e1000_ich8lan: 1796 /* Reduce concurrent DMA requests to 3 from 4 */ 1797 if ((hw->revision_id < 3) || 1798 ((hw->device_id != E1000_DEV_ID_ICH8_IGP_M_AMT) && 1799 (hw->device_id != E1000_DEV_ID_ICH8_IGP_M))) 1800 reg_tarc0 |= ((1 << 29)|(1 << 28)); 1801 1802 reg_ctrl_ext = E1000_READ_REG(hw, CTRL_EXT); 1803 reg_ctrl_ext |= (1 << 22); 1804 E1000_WRITE_REG(hw, CTRL_EXT, reg_ctrl_ext); 1805 1806 /* workaround TX hang with TSO=on */ 1807 reg_tarc0 |= ((1 << 27)|(1 << 26)|(1 << 24)|(1 << 23)); 1808 1809 /* Multiple read bit is reversed polarity */ 1810 reg_tctl = E1000_READ_REG(hw, TCTL); 1811 reg_tarc1 = E1000_READ_REG(hw, TARC1); 1812 if (reg_tctl & E1000_TCTL_MULR) 1813 reg_tarc1 &= ~(1 << 28); 1814 else 1815 reg_tarc1 |= (1 << 28); 1816 1817 /* workaround TX hang with TSO=on */ 1818 reg_tarc1 |= ((1 << 30)|(1 << 26)|(1 << 24)); 1819 1820 E1000_WRITE_REG(hw, TARC1, reg_tarc1); 1821 break; 1822 default: 1823 break; 1824 } 1825 1826 E1000_WRITE_REG(hw, TARC0, reg_tarc0); 1827 } 1828 } 1829 1830 /****************************************************************************** 1831 * Performs basic configuration of the adapter. 1832 * 1833 * hw - Struct containing variables accessed by shared code 1834 * 1835 * Assumes that the controller has previously been reset and is in a 1836 * post-reset uninitialized state. Initializes the receive address registers, 1837 * multicast table, and VLAN filter table. Calls routines to setup link 1838 * configuration and flow control settings. Clears all on-chip counters. Leaves 1839 * the transmit and receive units disabled and uninitialized. 1840 *****************************************************************************/ 1841 static int 1842 e1000_init_hw(struct e1000_hw *hw, unsigned char enetaddr[6]) 1843 { 1844 uint32_t ctrl; 1845 uint32_t i; 1846 int32_t ret_val; 1847 uint16_t pcix_cmd_word; 1848 uint16_t pcix_stat_hi_word; 1849 uint16_t cmd_mmrbc; 1850 uint16_t stat_mmrbc; 1851 uint32_t mta_size; 1852 uint32_t reg_data; 1853 uint32_t ctrl_ext; 1854 DEBUGFUNC(); 1855 /* force full DMA clock frequency for 10/100 on ICH8 A0-B0 */ 1856 if ((hw->mac_type == e1000_ich8lan) && 1857 ((hw->revision_id < 3) || 1858 ((hw->device_id != E1000_DEV_ID_ICH8_IGP_M_AMT) && 1859 (hw->device_id != E1000_DEV_ID_ICH8_IGP_M)))) { 1860 reg_data = E1000_READ_REG(hw, STATUS); 1861 reg_data &= ~0x80000000; 1862 E1000_WRITE_REG(hw, STATUS, reg_data); 1863 } 1864 /* Do not need initialize Identification LED */ 1865 1866 /* Set the media type and TBI compatibility */ 1867 e1000_set_media_type(hw); 1868 1869 /* Must be called after e1000_set_media_type 1870 * because media_type is used */ 1871 e1000_initialize_hardware_bits(hw); 1872 1873 /* Disabling VLAN filtering. */ 1874 DEBUGOUT("Initializing the IEEE VLAN\n"); 1875 /* VET hardcoded to standard value and VFTA removed in ICH8 LAN */ 1876 if (hw->mac_type != e1000_ich8lan) { 1877 if (hw->mac_type < e1000_82545_rev_3) 1878 E1000_WRITE_REG(hw, VET, 0); 1879 e1000_clear_vfta(hw); 1880 } 1881 1882 /* For 82542 (rev 2.0), disable MWI and put the receiver into reset */ 1883 if (hw->mac_type == e1000_82542_rev2_0) { 1884 DEBUGOUT("Disabling MWI on 82542 rev 2.0\n"); 1885 #ifdef CONFIG_DM_ETH 1886 dm_pci_write_config16(hw->pdev, PCI_COMMAND, 1887 hw-> 1888 pci_cmd_word & ~PCI_COMMAND_INVALIDATE); 1889 #else 1890 pci_write_config_word(hw->pdev, PCI_COMMAND, 1891 hw-> 1892 pci_cmd_word & ~PCI_COMMAND_INVALIDATE); 1893 #endif 1894 E1000_WRITE_REG(hw, RCTL, E1000_RCTL_RST); 1895 E1000_WRITE_FLUSH(hw); 1896 mdelay(5); 1897 } 1898 1899 /* Setup the receive address. This involves initializing all of the Receive 1900 * Address Registers (RARs 0 - 15). 1901 */ 1902 e1000_init_rx_addrs(hw, enetaddr); 1903 1904 /* For 82542 (rev 2.0), take the receiver out of reset and enable MWI */ 1905 if (hw->mac_type == e1000_82542_rev2_0) { 1906 E1000_WRITE_REG(hw, RCTL, 0); 1907 E1000_WRITE_FLUSH(hw); 1908 mdelay(1); 1909 #ifdef CONFIG_DM_ETH 1910 dm_pci_write_config16(hw->pdev, PCI_COMMAND, hw->pci_cmd_word); 1911 #else 1912 pci_write_config_word(hw->pdev, PCI_COMMAND, hw->pci_cmd_word); 1913 #endif 1914 } 1915 1916 /* Zero out the Multicast HASH table */ 1917 DEBUGOUT("Zeroing the MTA\n"); 1918 mta_size = E1000_MC_TBL_SIZE; 1919 if (hw->mac_type == e1000_ich8lan) 1920 mta_size = E1000_MC_TBL_SIZE_ICH8LAN; 1921 for (i = 0; i < mta_size; i++) { 1922 E1000_WRITE_REG_ARRAY(hw, MTA, i, 0); 1923 /* use write flush to prevent Memory Write Block (MWB) from 1924 * occuring when accessing our register space */ 1925 E1000_WRITE_FLUSH(hw); 1926 } 1927 1928 switch (hw->mac_type) { 1929 case e1000_82545_rev_3: 1930 case e1000_82546_rev_3: 1931 case e1000_igb: 1932 break; 1933 default: 1934 /* Workaround for PCI-X problem when BIOS sets MMRBC incorrectly. */ 1935 if (hw->bus_type == e1000_bus_type_pcix) { 1936 #ifdef CONFIG_DM_ETH 1937 dm_pci_read_config16(hw->pdev, PCIX_COMMAND_REGISTER, 1938 &pcix_cmd_word); 1939 dm_pci_read_config16(hw->pdev, PCIX_STATUS_REGISTER_HI, 1940 &pcix_stat_hi_word); 1941 #else 1942 pci_read_config_word(hw->pdev, PCIX_COMMAND_REGISTER, 1943 &pcix_cmd_word); 1944 pci_read_config_word(hw->pdev, PCIX_STATUS_REGISTER_HI, 1945 &pcix_stat_hi_word); 1946 #endif 1947 cmd_mmrbc = 1948 (pcix_cmd_word & PCIX_COMMAND_MMRBC_MASK) >> 1949 PCIX_COMMAND_MMRBC_SHIFT; 1950 stat_mmrbc = 1951 (pcix_stat_hi_word & PCIX_STATUS_HI_MMRBC_MASK) >> 1952 PCIX_STATUS_HI_MMRBC_SHIFT; 1953 if (stat_mmrbc == PCIX_STATUS_HI_MMRBC_4K) 1954 stat_mmrbc = PCIX_STATUS_HI_MMRBC_2K; 1955 if (cmd_mmrbc > stat_mmrbc) { 1956 pcix_cmd_word &= ~PCIX_COMMAND_MMRBC_MASK; 1957 pcix_cmd_word |= stat_mmrbc << PCIX_COMMAND_MMRBC_SHIFT; 1958 #ifdef CONFIG_DM_ETH 1959 dm_pci_write_config16(hw->pdev, PCIX_COMMAND_REGISTER, 1960 pcix_cmd_word); 1961 #else 1962 pci_write_config_word(hw->pdev, PCIX_COMMAND_REGISTER, 1963 pcix_cmd_word); 1964 #endif 1965 } 1966 } 1967 break; 1968 } 1969 1970 /* More time needed for PHY to initialize */ 1971 if (hw->mac_type == e1000_ich8lan) 1972 mdelay(15); 1973 if (hw->mac_type == e1000_igb) 1974 mdelay(15); 1975 1976 /* Call a subroutine to configure the link and setup flow control. */ 1977 ret_val = e1000_setup_link(hw); 1978 1979 /* Set the transmit descriptor write-back policy */ 1980 if (hw->mac_type > e1000_82544) { 1981 ctrl = E1000_READ_REG(hw, TXDCTL); 1982 ctrl = 1983 (ctrl & ~E1000_TXDCTL_WTHRESH) | 1984 E1000_TXDCTL_FULL_TX_DESC_WB; 1985 E1000_WRITE_REG(hw, TXDCTL, ctrl); 1986 } 1987 1988 /* Set the receive descriptor write back policy */ 1989 if (hw->mac_type >= e1000_82571) { 1990 ctrl = E1000_READ_REG(hw, RXDCTL); 1991 ctrl = 1992 (ctrl & ~E1000_RXDCTL_WTHRESH) | 1993 E1000_RXDCTL_FULL_RX_DESC_WB; 1994 E1000_WRITE_REG(hw, RXDCTL, ctrl); 1995 } 1996 1997 switch (hw->mac_type) { 1998 default: 1999 break; 2000 case e1000_80003es2lan: 2001 /* Enable retransmit on late collisions */ 2002 reg_data = E1000_READ_REG(hw, TCTL); 2003 reg_data |= E1000_TCTL_RTLC; 2004 E1000_WRITE_REG(hw, TCTL, reg_data); 2005 2006 /* Configure Gigabit Carry Extend Padding */ 2007 reg_data = E1000_READ_REG(hw, TCTL_EXT); 2008 reg_data &= ~E1000_TCTL_EXT_GCEX_MASK; 2009 reg_data |= DEFAULT_80003ES2LAN_TCTL_EXT_GCEX; 2010 E1000_WRITE_REG(hw, TCTL_EXT, reg_data); 2011 2012 /* Configure Transmit Inter-Packet Gap */ 2013 reg_data = E1000_READ_REG(hw, TIPG); 2014 reg_data &= ~E1000_TIPG_IPGT_MASK; 2015 reg_data |= DEFAULT_80003ES2LAN_TIPG_IPGT_1000; 2016 E1000_WRITE_REG(hw, TIPG, reg_data); 2017 2018 reg_data = E1000_READ_REG_ARRAY(hw, FFLT, 0x0001); 2019 reg_data &= ~0x00100000; 2020 E1000_WRITE_REG_ARRAY(hw, FFLT, 0x0001, reg_data); 2021 /* Fall through */ 2022 case e1000_82571: 2023 case e1000_82572: 2024 case e1000_ich8lan: 2025 ctrl = E1000_READ_REG(hw, TXDCTL1); 2026 ctrl = (ctrl & ~E1000_TXDCTL_WTHRESH) 2027 | E1000_TXDCTL_FULL_TX_DESC_WB; 2028 E1000_WRITE_REG(hw, TXDCTL1, ctrl); 2029 break; 2030 case e1000_82573: 2031 case e1000_82574: 2032 reg_data = E1000_READ_REG(hw, GCR); 2033 reg_data |= E1000_GCR_L1_ACT_WITHOUT_L0S_RX; 2034 E1000_WRITE_REG(hw, GCR, reg_data); 2035 case e1000_igb: 2036 break; 2037 } 2038 2039 if (hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER || 2040 hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3) { 2041 ctrl_ext = E1000_READ_REG(hw, CTRL_EXT); 2042 /* Relaxed ordering must be disabled to avoid a parity 2043 * error crash in a PCI slot. */ 2044 ctrl_ext |= E1000_CTRL_EXT_RO_DIS; 2045 E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext); 2046 } 2047 2048 return ret_val; 2049 } 2050 2051 /****************************************************************************** 2052 * Configures flow control and link settings. 2053 * 2054 * hw - Struct containing variables accessed by shared code 2055 * 2056 * Determines which flow control settings to use. Calls the apropriate media- 2057 * specific link configuration function. Configures the flow control settings. 2058 * Assuming the adapter has a valid link partner, a valid link should be 2059 * established. Assumes the hardware has previously been reset and the 2060 * transmitter and receiver are not enabled. 2061 *****************************************************************************/ 2062 static int 2063 e1000_setup_link(struct e1000_hw *hw) 2064 { 2065 int32_t ret_val; 2066 #ifndef CONFIG_E1000_NO_NVM 2067 uint32_t ctrl_ext; 2068 uint16_t eeprom_data; 2069 #endif 2070 2071 DEBUGFUNC(); 2072 2073 /* In the case of the phy reset being blocked, we already have a link. 2074 * We do not have to set it up again. */ 2075 if (e1000_check_phy_reset_block(hw)) 2076 return E1000_SUCCESS; 2077 2078 #ifndef CONFIG_E1000_NO_NVM 2079 /* Read and store word 0x0F of the EEPROM. This word contains bits 2080 * that determine the hardware's default PAUSE (flow control) mode, 2081 * a bit that determines whether the HW defaults to enabling or 2082 * disabling auto-negotiation, and the direction of the 2083 * SW defined pins. If there is no SW over-ride of the flow 2084 * control setting, then the variable hw->fc will 2085 * be initialized based on a value in the EEPROM. 2086 */ 2087 if (e1000_read_eeprom(hw, EEPROM_INIT_CONTROL2_REG, 1, 2088 &eeprom_data) < 0) { 2089 DEBUGOUT("EEPROM Read Error\n"); 2090 return -E1000_ERR_EEPROM; 2091 } 2092 #endif 2093 if (hw->fc == e1000_fc_default) { 2094 switch (hw->mac_type) { 2095 case e1000_ich8lan: 2096 case e1000_82573: 2097 case e1000_82574: 2098 case e1000_igb: 2099 hw->fc = e1000_fc_full; 2100 break; 2101 default: 2102 #ifndef CONFIG_E1000_NO_NVM 2103 ret_val = e1000_read_eeprom(hw, 2104 EEPROM_INIT_CONTROL2_REG, 1, &eeprom_data); 2105 if (ret_val) { 2106 DEBUGOUT("EEPROM Read Error\n"); 2107 return -E1000_ERR_EEPROM; 2108 } 2109 if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) == 0) 2110 hw->fc = e1000_fc_none; 2111 else if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) == 2112 EEPROM_WORD0F_ASM_DIR) 2113 hw->fc = e1000_fc_tx_pause; 2114 else 2115 #endif 2116 hw->fc = e1000_fc_full; 2117 break; 2118 } 2119 } 2120 2121 /* We want to save off the original Flow Control configuration just 2122 * in case we get disconnected and then reconnected into a different 2123 * hub or switch with different Flow Control capabilities. 2124 */ 2125 if (hw->mac_type == e1000_82542_rev2_0) 2126 hw->fc &= (~e1000_fc_tx_pause); 2127 2128 if ((hw->mac_type < e1000_82543) && (hw->report_tx_early == 1)) 2129 hw->fc &= (~e1000_fc_rx_pause); 2130 2131 hw->original_fc = hw->fc; 2132 2133 DEBUGOUT("After fix-ups FlowControl is now = %x\n", hw->fc); 2134 2135 #ifndef CONFIG_E1000_NO_NVM 2136 /* Take the 4 bits from EEPROM word 0x0F that determine the initial 2137 * polarity value for the SW controlled pins, and setup the 2138 * Extended Device Control reg with that info. 2139 * This is needed because one of the SW controlled pins is used for 2140 * signal detection. So this should be done before e1000_setup_pcs_link() 2141 * or e1000_phy_setup() is called. 2142 */ 2143 if (hw->mac_type == e1000_82543) { 2144 ctrl_ext = ((eeprom_data & EEPROM_WORD0F_SWPDIO_EXT) << 2145 SWDPIO__EXT_SHIFT); 2146 E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext); 2147 } 2148 #endif 2149 2150 /* Call the necessary subroutine to configure the link. */ 2151 ret_val = (hw->media_type == e1000_media_type_fiber) ? 2152 e1000_setup_fiber_link(hw) : e1000_setup_copper_link(hw); 2153 if (ret_val < 0) { 2154 return ret_val; 2155 } 2156 2157 /* Initialize the flow control address, type, and PAUSE timer 2158 * registers to their default values. This is done even if flow 2159 * control is disabled, because it does not hurt anything to 2160 * initialize these registers. 2161 */ 2162 DEBUGOUT("Initializing the Flow Control address, type" 2163 "and timer regs\n"); 2164 2165 /* FCAL/H and FCT are hardcoded to standard values in e1000_ich8lan. */ 2166 if (hw->mac_type != e1000_ich8lan) { 2167 E1000_WRITE_REG(hw, FCT, FLOW_CONTROL_TYPE); 2168 E1000_WRITE_REG(hw, FCAH, FLOW_CONTROL_ADDRESS_HIGH); 2169 E1000_WRITE_REG(hw, FCAL, FLOW_CONTROL_ADDRESS_LOW); 2170 } 2171 2172 E1000_WRITE_REG(hw, FCTTV, hw->fc_pause_time); 2173 2174 /* Set the flow control receive threshold registers. Normally, 2175 * these registers will be set to a default threshold that may be 2176 * adjusted later by the driver's runtime code. However, if the 2177 * ability to transmit pause frames in not enabled, then these 2178 * registers will be set to 0. 2179 */ 2180 if (!(hw->fc & e1000_fc_tx_pause)) { 2181 E1000_WRITE_REG(hw, FCRTL, 0); 2182 E1000_WRITE_REG(hw, FCRTH, 0); 2183 } else { 2184 /* We need to set up the Receive Threshold high and low water marks 2185 * as well as (optionally) enabling the transmission of XON frames. 2186 */ 2187 if (hw->fc_send_xon) { 2188 E1000_WRITE_REG(hw, FCRTL, 2189 (hw->fc_low_water | E1000_FCRTL_XONE)); 2190 E1000_WRITE_REG(hw, FCRTH, hw->fc_high_water); 2191 } else { 2192 E1000_WRITE_REG(hw, FCRTL, hw->fc_low_water); 2193 E1000_WRITE_REG(hw, FCRTH, hw->fc_high_water); 2194 } 2195 } 2196 return ret_val; 2197 } 2198 2199 /****************************************************************************** 2200 * Sets up link for a fiber based adapter 2201 * 2202 * hw - Struct containing variables accessed by shared code 2203 * 2204 * Manipulates Physical Coding Sublayer functions in order to configure 2205 * link. Assumes the hardware has been previously reset and the transmitter 2206 * and receiver are not enabled. 2207 *****************************************************************************/ 2208 static int 2209 e1000_setup_fiber_link(struct e1000_hw *hw) 2210 { 2211 uint32_t ctrl; 2212 uint32_t status; 2213 uint32_t txcw = 0; 2214 uint32_t i; 2215 uint32_t signal; 2216 int32_t ret_val; 2217 2218 DEBUGFUNC(); 2219 /* On adapters with a MAC newer that 82544, SW Defineable pin 1 will be 2220 * set when the optics detect a signal. On older adapters, it will be 2221 * cleared when there is a signal 2222 */ 2223 ctrl = E1000_READ_REG(hw, CTRL); 2224 if ((hw->mac_type > e1000_82544) && !(ctrl & E1000_CTRL_ILOS)) 2225 signal = E1000_CTRL_SWDPIN1; 2226 else 2227 signal = 0; 2228 2229 printf("signal for %s is %x (ctrl %08x)!!!!\n", hw->name, signal, 2230 ctrl); 2231 /* Take the link out of reset */ 2232 ctrl &= ~(E1000_CTRL_LRST); 2233 2234 e1000_config_collision_dist(hw); 2235 2236 /* Check for a software override of the flow control settings, and setup 2237 * the device accordingly. If auto-negotiation is enabled, then software 2238 * will have to set the "PAUSE" bits to the correct value in the Tranmsit 2239 * Config Word Register (TXCW) and re-start auto-negotiation. However, if 2240 * auto-negotiation is disabled, then software will have to manually 2241 * configure the two flow control enable bits in the CTRL register. 2242 * 2243 * The possible values of the "fc" parameter are: 2244 * 0: Flow control is completely disabled 2245 * 1: Rx flow control is enabled (we can receive pause frames, but 2246 * not send pause frames). 2247 * 2: Tx flow control is enabled (we can send pause frames but we do 2248 * not support receiving pause frames). 2249 * 3: Both Rx and TX flow control (symmetric) are enabled. 2250 */ 2251 switch (hw->fc) { 2252 case e1000_fc_none: 2253 /* Flow control is completely disabled by a software over-ride. */ 2254 txcw = (E1000_TXCW_ANE | E1000_TXCW_FD); 2255 break; 2256 case e1000_fc_rx_pause: 2257 /* RX Flow control is enabled and TX Flow control is disabled by a 2258 * software over-ride. Since there really isn't a way to advertise 2259 * that we are capable of RX Pause ONLY, we will advertise that we 2260 * support both symmetric and asymmetric RX PAUSE. Later, we will 2261 * disable the adapter's ability to send PAUSE frames. 2262 */ 2263 txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK); 2264 break; 2265 case e1000_fc_tx_pause: 2266 /* TX Flow control is enabled, and RX Flow control is disabled, by a 2267 * software over-ride. 2268 */ 2269 txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_ASM_DIR); 2270 break; 2271 case e1000_fc_full: 2272 /* Flow control (both RX and TX) is enabled by a software over-ride. */ 2273 txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK); 2274 break; 2275 default: 2276 DEBUGOUT("Flow control param set incorrectly\n"); 2277 return -E1000_ERR_CONFIG; 2278 break; 2279 } 2280 2281 /* Since auto-negotiation is enabled, take the link out of reset (the link 2282 * will be in reset, because we previously reset the chip). This will 2283 * restart auto-negotiation. If auto-neogtiation is successful then the 2284 * link-up status bit will be set and the flow control enable bits (RFCE 2285 * and TFCE) will be set according to their negotiated value. 2286 */ 2287 DEBUGOUT("Auto-negotiation enabled (%#x)\n", txcw); 2288 2289 E1000_WRITE_REG(hw, TXCW, txcw); 2290 E1000_WRITE_REG(hw, CTRL, ctrl); 2291 E1000_WRITE_FLUSH(hw); 2292 2293 hw->txcw = txcw; 2294 mdelay(1); 2295 2296 /* If we have a signal (the cable is plugged in) then poll for a "Link-Up" 2297 * indication in the Device Status Register. Time-out if a link isn't 2298 * seen in 500 milliseconds seconds (Auto-negotiation should complete in 2299 * less than 500 milliseconds even if the other end is doing it in SW). 2300 */ 2301 if ((E1000_READ_REG(hw, CTRL) & E1000_CTRL_SWDPIN1) == signal) { 2302 DEBUGOUT("Looking for Link\n"); 2303 for (i = 0; i < (LINK_UP_TIMEOUT / 10); i++) { 2304 mdelay(10); 2305 status = E1000_READ_REG(hw, STATUS); 2306 if (status & E1000_STATUS_LU) 2307 break; 2308 } 2309 if (i == (LINK_UP_TIMEOUT / 10)) { 2310 /* AutoNeg failed to achieve a link, so we'll call 2311 * e1000_check_for_link. This routine will force the link up if we 2312 * detect a signal. This will allow us to communicate with 2313 * non-autonegotiating link partners. 2314 */ 2315 DEBUGOUT("Never got a valid link from auto-neg!!!\n"); 2316 hw->autoneg_failed = 1; 2317 ret_val = e1000_check_for_link(hw); 2318 if (ret_val < 0) { 2319 DEBUGOUT("Error while checking for link\n"); 2320 return ret_val; 2321 } 2322 hw->autoneg_failed = 0; 2323 } else { 2324 hw->autoneg_failed = 0; 2325 DEBUGOUT("Valid Link Found\n"); 2326 } 2327 } else { 2328 DEBUGOUT("No Signal Detected\n"); 2329 return -E1000_ERR_NOLINK; 2330 } 2331 return 0; 2332 } 2333 2334 /****************************************************************************** 2335 * Make sure we have a valid PHY and change PHY mode before link setup. 2336 * 2337 * hw - Struct containing variables accessed by shared code 2338 ******************************************************************************/ 2339 static int32_t 2340 e1000_copper_link_preconfig(struct e1000_hw *hw) 2341 { 2342 uint32_t ctrl; 2343 int32_t ret_val; 2344 uint16_t phy_data; 2345 2346 DEBUGFUNC(); 2347 2348 ctrl = E1000_READ_REG(hw, CTRL); 2349 /* With 82543, we need to force speed and duplex on the MAC equal to what 2350 * the PHY speed and duplex configuration is. In addition, we need to 2351 * perform a hardware reset on the PHY to take it out of reset. 2352 */ 2353 if (hw->mac_type > e1000_82543) { 2354 ctrl |= E1000_CTRL_SLU; 2355 ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); 2356 E1000_WRITE_REG(hw, CTRL, ctrl); 2357 } else { 2358 ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX 2359 | E1000_CTRL_SLU); 2360 E1000_WRITE_REG(hw, CTRL, ctrl); 2361 ret_val = e1000_phy_hw_reset(hw); 2362 if (ret_val) 2363 return ret_val; 2364 } 2365 2366 /* Make sure we have a valid PHY */ 2367 ret_val = e1000_detect_gig_phy(hw); 2368 if (ret_val) { 2369 DEBUGOUT("Error, did not detect valid phy.\n"); 2370 return ret_val; 2371 } 2372 DEBUGOUT("Phy ID = %x\n", hw->phy_id); 2373 2374 /* Set PHY to class A mode (if necessary) */ 2375 ret_val = e1000_set_phy_mode(hw); 2376 if (ret_val) 2377 return ret_val; 2378 if ((hw->mac_type == e1000_82545_rev_3) || 2379 (hw->mac_type == e1000_82546_rev_3)) { 2380 ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, 2381 &phy_data); 2382 phy_data |= 0x00000008; 2383 ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, 2384 phy_data); 2385 } 2386 2387 if (hw->mac_type <= e1000_82543 || 2388 hw->mac_type == e1000_82541 || hw->mac_type == e1000_82547 || 2389 hw->mac_type == e1000_82541_rev_2 2390 || hw->mac_type == e1000_82547_rev_2) 2391 hw->phy_reset_disable = false; 2392 2393 return E1000_SUCCESS; 2394 } 2395 2396 /***************************************************************************** 2397 * 2398 * This function sets the lplu state according to the active flag. When 2399 * activating lplu this function also disables smart speed and vise versa. 2400 * lplu will not be activated unless the device autonegotiation advertisment 2401 * meets standards of either 10 or 10/100 or 10/100/1000 at all duplexes. 2402 * hw: Struct containing variables accessed by shared code 2403 * active - true to enable lplu false to disable lplu. 2404 * 2405 * returns: - E1000_ERR_PHY if fail to read/write the PHY 2406 * E1000_SUCCESS at any other case. 2407 * 2408 ****************************************************************************/ 2409 2410 static int32_t 2411 e1000_set_d3_lplu_state(struct e1000_hw *hw, bool active) 2412 { 2413 uint32_t phy_ctrl = 0; 2414 int32_t ret_val; 2415 uint16_t phy_data; 2416 DEBUGFUNC(); 2417 2418 if (hw->phy_type != e1000_phy_igp && hw->phy_type != e1000_phy_igp_2 2419 && hw->phy_type != e1000_phy_igp_3) 2420 return E1000_SUCCESS; 2421 2422 /* During driver activity LPLU should not be used or it will attain link 2423 * from the lowest speeds starting from 10Mbps. The capability is used 2424 * for Dx transitions and states */ 2425 if (hw->mac_type == e1000_82541_rev_2 2426 || hw->mac_type == e1000_82547_rev_2) { 2427 ret_val = e1000_read_phy_reg(hw, IGP01E1000_GMII_FIFO, 2428 &phy_data); 2429 if (ret_val) 2430 return ret_val; 2431 } else if (hw->mac_type == e1000_ich8lan) { 2432 /* MAC writes into PHY register based on the state transition 2433 * and start auto-negotiation. SW driver can overwrite the 2434 * settings in CSR PHY power control E1000_PHY_CTRL register. */ 2435 phy_ctrl = E1000_READ_REG(hw, PHY_CTRL); 2436 } else { 2437 ret_val = e1000_read_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, 2438 &phy_data); 2439 if (ret_val) 2440 return ret_val; 2441 } 2442 2443 if (!active) { 2444 if (hw->mac_type == e1000_82541_rev_2 || 2445 hw->mac_type == e1000_82547_rev_2) { 2446 phy_data &= ~IGP01E1000_GMII_FLEX_SPD; 2447 ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO, 2448 phy_data); 2449 if (ret_val) 2450 return ret_val; 2451 } else { 2452 if (hw->mac_type == e1000_ich8lan) { 2453 phy_ctrl &= ~E1000_PHY_CTRL_NOND0A_LPLU; 2454 E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl); 2455 } else { 2456 phy_data &= ~IGP02E1000_PM_D3_LPLU; 2457 ret_val = e1000_write_phy_reg(hw, 2458 IGP02E1000_PHY_POWER_MGMT, phy_data); 2459 if (ret_val) 2460 return ret_val; 2461 } 2462 } 2463 2464 /* LPLU and SmartSpeed are mutually exclusive. LPLU is used during 2465 * Dx states where the power conservation is most important. During 2466 * driver activity we should enable SmartSpeed, so performance is 2467 * maintained. */ 2468 if (hw->smart_speed == e1000_smart_speed_on) { 2469 ret_val = e1000_read_phy_reg(hw, 2470 IGP01E1000_PHY_PORT_CONFIG, &phy_data); 2471 if (ret_val) 2472 return ret_val; 2473 2474 phy_data |= IGP01E1000_PSCFR_SMART_SPEED; 2475 ret_val = e1000_write_phy_reg(hw, 2476 IGP01E1000_PHY_PORT_CONFIG, phy_data); 2477 if (ret_val) 2478 return ret_val; 2479 } else if (hw->smart_speed == e1000_smart_speed_off) { 2480 ret_val = e1000_read_phy_reg(hw, 2481 IGP01E1000_PHY_PORT_CONFIG, &phy_data); 2482 if (ret_val) 2483 return ret_val; 2484 2485 phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED; 2486 ret_val = e1000_write_phy_reg(hw, 2487 IGP01E1000_PHY_PORT_CONFIG, phy_data); 2488 if (ret_val) 2489 return ret_val; 2490 } 2491 2492 } else if ((hw->autoneg_advertised == AUTONEG_ADVERTISE_SPEED_DEFAULT) 2493 || (hw->autoneg_advertised == AUTONEG_ADVERTISE_10_ALL) || 2494 (hw->autoneg_advertised == AUTONEG_ADVERTISE_10_100_ALL)) { 2495 2496 if (hw->mac_type == e1000_82541_rev_2 || 2497 hw->mac_type == e1000_82547_rev_2) { 2498 phy_data |= IGP01E1000_GMII_FLEX_SPD; 2499 ret_val = e1000_write_phy_reg(hw, 2500 IGP01E1000_GMII_FIFO, phy_data); 2501 if (ret_val) 2502 return ret_val; 2503 } else { 2504 if (hw->mac_type == e1000_ich8lan) { 2505 phy_ctrl |= E1000_PHY_CTRL_NOND0A_LPLU; 2506 E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl); 2507 } else { 2508 phy_data |= IGP02E1000_PM_D3_LPLU; 2509 ret_val = e1000_write_phy_reg(hw, 2510 IGP02E1000_PHY_POWER_MGMT, phy_data); 2511 if (ret_val) 2512 return ret_val; 2513 } 2514 } 2515 2516 /* When LPLU is enabled we should disable SmartSpeed */ 2517 ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, 2518 &phy_data); 2519 if (ret_val) 2520 return ret_val; 2521 2522 phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED; 2523 ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, 2524 phy_data); 2525 if (ret_val) 2526 return ret_val; 2527 } 2528 return E1000_SUCCESS; 2529 } 2530 2531 /***************************************************************************** 2532 * 2533 * This function sets the lplu d0 state according to the active flag. When 2534 * activating lplu this function also disables smart speed and vise versa. 2535 * lplu will not be activated unless the device autonegotiation advertisment 2536 * meets standards of either 10 or 10/100 or 10/100/1000 at all duplexes. 2537 * hw: Struct containing variables accessed by shared code 2538 * active - true to enable lplu false to disable lplu. 2539 * 2540 * returns: - E1000_ERR_PHY if fail to read/write the PHY 2541 * E1000_SUCCESS at any other case. 2542 * 2543 ****************************************************************************/ 2544 2545 static int32_t 2546 e1000_set_d0_lplu_state(struct e1000_hw *hw, bool active) 2547 { 2548 uint32_t phy_ctrl = 0; 2549 int32_t ret_val; 2550 uint16_t phy_data; 2551 DEBUGFUNC(); 2552 2553 if (hw->mac_type <= e1000_82547_rev_2) 2554 return E1000_SUCCESS; 2555 2556 if (hw->mac_type == e1000_ich8lan) { 2557 phy_ctrl = E1000_READ_REG(hw, PHY_CTRL); 2558 } else if (hw->mac_type == e1000_igb) { 2559 phy_ctrl = E1000_READ_REG(hw, I210_PHY_CTRL); 2560 } else { 2561 ret_val = e1000_read_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, 2562 &phy_data); 2563 if (ret_val) 2564 return ret_val; 2565 } 2566 2567 if (!active) { 2568 if (hw->mac_type == e1000_ich8lan) { 2569 phy_ctrl &= ~E1000_PHY_CTRL_D0A_LPLU; 2570 E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl); 2571 } else if (hw->mac_type == e1000_igb) { 2572 phy_ctrl &= ~E1000_PHY_CTRL_D0A_LPLU; 2573 E1000_WRITE_REG(hw, I210_PHY_CTRL, phy_ctrl); 2574 } else { 2575 phy_data &= ~IGP02E1000_PM_D0_LPLU; 2576 ret_val = e1000_write_phy_reg(hw, 2577 IGP02E1000_PHY_POWER_MGMT, phy_data); 2578 if (ret_val) 2579 return ret_val; 2580 } 2581 2582 if (hw->mac_type == e1000_igb) 2583 return E1000_SUCCESS; 2584 2585 /* LPLU and SmartSpeed are mutually exclusive. LPLU is used during 2586 * Dx states where the power conservation is most important. During 2587 * driver activity we should enable SmartSpeed, so performance is 2588 * maintained. */ 2589 if (hw->smart_speed == e1000_smart_speed_on) { 2590 ret_val = e1000_read_phy_reg(hw, 2591 IGP01E1000_PHY_PORT_CONFIG, &phy_data); 2592 if (ret_val) 2593 return ret_val; 2594 2595 phy_data |= IGP01E1000_PSCFR_SMART_SPEED; 2596 ret_val = e1000_write_phy_reg(hw, 2597 IGP01E1000_PHY_PORT_CONFIG, phy_data); 2598 if (ret_val) 2599 return ret_val; 2600 } else if (hw->smart_speed == e1000_smart_speed_off) { 2601 ret_val = e1000_read_phy_reg(hw, 2602 IGP01E1000_PHY_PORT_CONFIG, &phy_data); 2603 if (ret_val) 2604 return ret_val; 2605 2606 phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED; 2607 ret_val = e1000_write_phy_reg(hw, 2608 IGP01E1000_PHY_PORT_CONFIG, phy_data); 2609 if (ret_val) 2610 return ret_val; 2611 } 2612 2613 2614 } else { 2615 2616 if (hw->mac_type == e1000_ich8lan) { 2617 phy_ctrl |= E1000_PHY_CTRL_D0A_LPLU; 2618 E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl); 2619 } else if (hw->mac_type == e1000_igb) { 2620 phy_ctrl |= E1000_PHY_CTRL_D0A_LPLU; 2621 E1000_WRITE_REG(hw, I210_PHY_CTRL, phy_ctrl); 2622 } else { 2623 phy_data |= IGP02E1000_PM_D0_LPLU; 2624 ret_val = e1000_write_phy_reg(hw, 2625 IGP02E1000_PHY_POWER_MGMT, phy_data); 2626 if (ret_val) 2627 return ret_val; 2628 } 2629 2630 if (hw->mac_type == e1000_igb) 2631 return E1000_SUCCESS; 2632 2633 /* When LPLU is enabled we should disable SmartSpeed */ 2634 ret_val = e1000_read_phy_reg(hw, 2635 IGP01E1000_PHY_PORT_CONFIG, &phy_data); 2636 if (ret_val) 2637 return ret_val; 2638 2639 phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED; 2640 ret_val = e1000_write_phy_reg(hw, 2641 IGP01E1000_PHY_PORT_CONFIG, phy_data); 2642 if (ret_val) 2643 return ret_val; 2644 2645 } 2646 return E1000_SUCCESS; 2647 } 2648 2649 /******************************************************************** 2650 * Copper link setup for e1000_phy_igp series. 2651 * 2652 * hw - Struct containing variables accessed by shared code 2653 *********************************************************************/ 2654 static int32_t 2655 e1000_copper_link_igp_setup(struct e1000_hw *hw) 2656 { 2657 uint32_t led_ctrl; 2658 int32_t ret_val; 2659 uint16_t phy_data; 2660 2661 DEBUGFUNC(); 2662 2663 if (hw->phy_reset_disable) 2664 return E1000_SUCCESS; 2665 2666 ret_val = e1000_phy_reset(hw); 2667 if (ret_val) { 2668 DEBUGOUT("Error Resetting the PHY\n"); 2669 return ret_val; 2670 } 2671 2672 /* Wait 15ms for MAC to configure PHY from eeprom settings */ 2673 mdelay(15); 2674 if (hw->mac_type != e1000_ich8lan) { 2675 /* Configure activity LED after PHY reset */ 2676 led_ctrl = E1000_READ_REG(hw, LEDCTL); 2677 led_ctrl &= IGP_ACTIVITY_LED_MASK; 2678 led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE); 2679 E1000_WRITE_REG(hw, LEDCTL, led_ctrl); 2680 } 2681 2682 /* The NVM settings will configure LPLU in D3 for IGP2 and IGP3 PHYs */ 2683 if (hw->phy_type == e1000_phy_igp) { 2684 /* disable lplu d3 during driver init */ 2685 ret_val = e1000_set_d3_lplu_state(hw, false); 2686 if (ret_val) { 2687 DEBUGOUT("Error Disabling LPLU D3\n"); 2688 return ret_val; 2689 } 2690 } 2691 2692 /* disable lplu d0 during driver init */ 2693 ret_val = e1000_set_d0_lplu_state(hw, false); 2694 if (ret_val) { 2695 DEBUGOUT("Error Disabling LPLU D0\n"); 2696 return ret_val; 2697 } 2698 /* Configure mdi-mdix settings */ 2699 ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, &phy_data); 2700 if (ret_val) 2701 return ret_val; 2702 2703 if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) { 2704 hw->dsp_config_state = e1000_dsp_config_disabled; 2705 /* Force MDI for earlier revs of the IGP PHY */ 2706 phy_data &= ~(IGP01E1000_PSCR_AUTO_MDIX 2707 | IGP01E1000_PSCR_FORCE_MDI_MDIX); 2708 hw->mdix = 1; 2709 2710 } else { 2711 hw->dsp_config_state = e1000_dsp_config_enabled; 2712 phy_data &= ~IGP01E1000_PSCR_AUTO_MDIX; 2713 2714 switch (hw->mdix) { 2715 case 1: 2716 phy_data &= ~IGP01E1000_PSCR_FORCE_MDI_MDIX; 2717 break; 2718 case 2: 2719 phy_data |= IGP01E1000_PSCR_FORCE_MDI_MDIX; 2720 break; 2721 case 0: 2722 default: 2723 phy_data |= IGP01E1000_PSCR_AUTO_MDIX; 2724 break; 2725 } 2726 } 2727 ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, phy_data); 2728 if (ret_val) 2729 return ret_val; 2730 2731 /* set auto-master slave resolution settings */ 2732 if (hw->autoneg) { 2733 e1000_ms_type phy_ms_setting = hw->master_slave; 2734 2735 if (hw->ffe_config_state == e1000_ffe_config_active) 2736 hw->ffe_config_state = e1000_ffe_config_enabled; 2737 2738 if (hw->dsp_config_state == e1000_dsp_config_activated) 2739 hw->dsp_config_state = e1000_dsp_config_enabled; 2740 2741 /* when autonegotiation advertisment is only 1000Mbps then we 2742 * should disable SmartSpeed and enable Auto MasterSlave 2743 * resolution as hardware default. */ 2744 if (hw->autoneg_advertised == ADVERTISE_1000_FULL) { 2745 /* Disable SmartSpeed */ 2746 ret_val = e1000_read_phy_reg(hw, 2747 IGP01E1000_PHY_PORT_CONFIG, &phy_data); 2748 if (ret_val) 2749 return ret_val; 2750 phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED; 2751 ret_val = e1000_write_phy_reg(hw, 2752 IGP01E1000_PHY_PORT_CONFIG, phy_data); 2753 if (ret_val) 2754 return ret_val; 2755 /* Set auto Master/Slave resolution process */ 2756 ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, 2757 &phy_data); 2758 if (ret_val) 2759 return ret_val; 2760 phy_data &= ~CR_1000T_MS_ENABLE; 2761 ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, 2762 phy_data); 2763 if (ret_val) 2764 return ret_val; 2765 } 2766 2767 ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &phy_data); 2768 if (ret_val) 2769 return ret_val; 2770 2771 /* load defaults for future use */ 2772 hw->original_master_slave = (phy_data & CR_1000T_MS_ENABLE) ? 2773 ((phy_data & CR_1000T_MS_VALUE) ? 2774 e1000_ms_force_master : 2775 e1000_ms_force_slave) : 2776 e1000_ms_auto; 2777 2778 switch (phy_ms_setting) { 2779 case e1000_ms_force_master: 2780 phy_data |= (CR_1000T_MS_ENABLE | CR_1000T_MS_VALUE); 2781 break; 2782 case e1000_ms_force_slave: 2783 phy_data |= CR_1000T_MS_ENABLE; 2784 phy_data &= ~(CR_1000T_MS_VALUE); 2785 break; 2786 case e1000_ms_auto: 2787 phy_data &= ~CR_1000T_MS_ENABLE; 2788 default: 2789 break; 2790 } 2791 ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, phy_data); 2792 if (ret_val) 2793 return ret_val; 2794 } 2795 2796 return E1000_SUCCESS; 2797 } 2798 2799 /***************************************************************************** 2800 * This function checks the mode of the firmware. 2801 * 2802 * returns - true when the mode is IAMT or false. 2803 ****************************************************************************/ 2804 bool 2805 e1000_check_mng_mode(struct e1000_hw *hw) 2806 { 2807 uint32_t fwsm; 2808 DEBUGFUNC(); 2809 2810 fwsm = E1000_READ_REG(hw, FWSM); 2811 2812 if (hw->mac_type == e1000_ich8lan) { 2813 if ((fwsm & E1000_FWSM_MODE_MASK) == 2814 (E1000_MNG_ICH_IAMT_MODE << E1000_FWSM_MODE_SHIFT)) 2815 return true; 2816 } else if ((fwsm & E1000_FWSM_MODE_MASK) == 2817 (E1000_MNG_IAMT_MODE << E1000_FWSM_MODE_SHIFT)) 2818 return true; 2819 2820 return false; 2821 } 2822 2823 static int32_t 2824 e1000_write_kmrn_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t data) 2825 { 2826 uint16_t swfw = E1000_SWFW_PHY0_SM; 2827 uint32_t reg_val; 2828 DEBUGFUNC(); 2829 2830 if (e1000_is_second_port(hw)) 2831 swfw = E1000_SWFW_PHY1_SM; 2832 2833 if (e1000_swfw_sync_acquire(hw, swfw)) 2834 return -E1000_ERR_SWFW_SYNC; 2835 2836 reg_val = ((reg_addr << E1000_KUMCTRLSTA_OFFSET_SHIFT) 2837 & E1000_KUMCTRLSTA_OFFSET) | data; 2838 E1000_WRITE_REG(hw, KUMCTRLSTA, reg_val); 2839 udelay(2); 2840 2841 return E1000_SUCCESS; 2842 } 2843 2844 static int32_t 2845 e1000_read_kmrn_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t *data) 2846 { 2847 uint16_t swfw = E1000_SWFW_PHY0_SM; 2848 uint32_t reg_val; 2849 DEBUGFUNC(); 2850 2851 if (e1000_is_second_port(hw)) 2852 swfw = E1000_SWFW_PHY1_SM; 2853 2854 if (e1000_swfw_sync_acquire(hw, swfw)) { 2855 debug("%s[%i]\n", __func__, __LINE__); 2856 return -E1000_ERR_SWFW_SYNC; 2857 } 2858 2859 /* Write register address */ 2860 reg_val = ((reg_addr << E1000_KUMCTRLSTA_OFFSET_SHIFT) & 2861 E1000_KUMCTRLSTA_OFFSET) | E1000_KUMCTRLSTA_REN; 2862 E1000_WRITE_REG(hw, KUMCTRLSTA, reg_val); 2863 udelay(2); 2864 2865 /* Read the data returned */ 2866 reg_val = E1000_READ_REG(hw, KUMCTRLSTA); 2867 *data = (uint16_t)reg_val; 2868 2869 return E1000_SUCCESS; 2870 } 2871 2872 /******************************************************************** 2873 * Copper link setup for e1000_phy_gg82563 series. 2874 * 2875 * hw - Struct containing variables accessed by shared code 2876 *********************************************************************/ 2877 static int32_t 2878 e1000_copper_link_ggp_setup(struct e1000_hw *hw) 2879 { 2880 int32_t ret_val; 2881 uint16_t phy_data; 2882 uint32_t reg_data; 2883 2884 DEBUGFUNC(); 2885 2886 if (!hw->phy_reset_disable) { 2887 /* Enable CRS on TX for half-duplex operation. */ 2888 ret_val = e1000_read_phy_reg(hw, 2889 GG82563_PHY_MAC_SPEC_CTRL, &phy_data); 2890 if (ret_val) 2891 return ret_val; 2892 2893 phy_data |= GG82563_MSCR_ASSERT_CRS_ON_TX; 2894 /* Use 25MHz for both link down and 1000BASE-T for Tx clock */ 2895 phy_data |= GG82563_MSCR_TX_CLK_1000MBPS_25MHZ; 2896 2897 ret_val = e1000_write_phy_reg(hw, 2898 GG82563_PHY_MAC_SPEC_CTRL, phy_data); 2899 if (ret_val) 2900 return ret_val; 2901 2902 /* Options: 2903 * MDI/MDI-X = 0 (default) 2904 * 0 - Auto for all speeds 2905 * 1 - MDI mode 2906 * 2 - MDI-X mode 2907 * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes) 2908 */ 2909 ret_val = e1000_read_phy_reg(hw, 2910 GG82563_PHY_SPEC_CTRL, &phy_data); 2911 if (ret_val) 2912 return ret_val; 2913 2914 phy_data &= ~GG82563_PSCR_CROSSOVER_MODE_MASK; 2915 2916 switch (hw->mdix) { 2917 case 1: 2918 phy_data |= GG82563_PSCR_CROSSOVER_MODE_MDI; 2919 break; 2920 case 2: 2921 phy_data |= GG82563_PSCR_CROSSOVER_MODE_MDIX; 2922 break; 2923 case 0: 2924 default: 2925 phy_data |= GG82563_PSCR_CROSSOVER_MODE_AUTO; 2926 break; 2927 } 2928 2929 /* Options: 2930 * disable_polarity_correction = 0 (default) 2931 * Automatic Correction for Reversed Cable Polarity 2932 * 0 - Disabled 2933 * 1 - Enabled 2934 */ 2935 phy_data &= ~GG82563_PSCR_POLARITY_REVERSAL_DISABLE; 2936 ret_val = e1000_write_phy_reg(hw, 2937 GG82563_PHY_SPEC_CTRL, phy_data); 2938 2939 if (ret_val) 2940 return ret_val; 2941 2942 /* SW Reset the PHY so all changes take effect */ 2943 ret_val = e1000_phy_reset(hw); 2944 if (ret_val) { 2945 DEBUGOUT("Error Resetting the PHY\n"); 2946 return ret_val; 2947 } 2948 } /* phy_reset_disable */ 2949 2950 if (hw->mac_type == e1000_80003es2lan) { 2951 /* Bypass RX and TX FIFO's */ 2952 ret_val = e1000_write_kmrn_reg(hw, 2953 E1000_KUMCTRLSTA_OFFSET_FIFO_CTRL, 2954 E1000_KUMCTRLSTA_FIFO_CTRL_RX_BYPASS 2955 | E1000_KUMCTRLSTA_FIFO_CTRL_TX_BYPASS); 2956 if (ret_val) 2957 return ret_val; 2958 2959 ret_val = e1000_read_phy_reg(hw, 2960 GG82563_PHY_SPEC_CTRL_2, &phy_data); 2961 if (ret_val) 2962 return ret_val; 2963 2964 phy_data &= ~GG82563_PSCR2_REVERSE_AUTO_NEG; 2965 ret_val = e1000_write_phy_reg(hw, 2966 GG82563_PHY_SPEC_CTRL_2, phy_data); 2967 2968 if (ret_val) 2969 return ret_val; 2970 2971 reg_data = E1000_READ_REG(hw, CTRL_EXT); 2972 reg_data &= ~(E1000_CTRL_EXT_LINK_MODE_MASK); 2973 E1000_WRITE_REG(hw, CTRL_EXT, reg_data); 2974 2975 ret_val = e1000_read_phy_reg(hw, 2976 GG82563_PHY_PWR_MGMT_CTRL, &phy_data); 2977 if (ret_val) 2978 return ret_val; 2979 2980 /* Do not init these registers when the HW is in IAMT mode, since the 2981 * firmware will have already initialized them. We only initialize 2982 * them if the HW is not in IAMT mode. 2983 */ 2984 if (e1000_check_mng_mode(hw) == false) { 2985 /* Enable Electrical Idle on the PHY */ 2986 phy_data |= GG82563_PMCR_ENABLE_ELECTRICAL_IDLE; 2987 ret_val = e1000_write_phy_reg(hw, 2988 GG82563_PHY_PWR_MGMT_CTRL, phy_data); 2989 if (ret_val) 2990 return ret_val; 2991 2992 ret_val = e1000_read_phy_reg(hw, 2993 GG82563_PHY_KMRN_MODE_CTRL, &phy_data); 2994 if (ret_val) 2995 return ret_val; 2996 2997 phy_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER; 2998 ret_val = e1000_write_phy_reg(hw, 2999 GG82563_PHY_KMRN_MODE_CTRL, phy_data); 3000 3001 if (ret_val) 3002 return ret_val; 3003 } 3004 3005 /* Workaround: Disable padding in Kumeran interface in the MAC 3006 * and in the PHY to avoid CRC errors. 3007 */ 3008 ret_val = e1000_read_phy_reg(hw, 3009 GG82563_PHY_INBAND_CTRL, &phy_data); 3010 if (ret_val) 3011 return ret_val; 3012 phy_data |= GG82563_ICR_DIS_PADDING; 3013 ret_val = e1000_write_phy_reg(hw, 3014 GG82563_PHY_INBAND_CTRL, phy_data); 3015 if (ret_val) 3016 return ret_val; 3017 } 3018 return E1000_SUCCESS; 3019 } 3020 3021 /******************************************************************** 3022 * Copper link setup for e1000_phy_m88 series. 3023 * 3024 * hw - Struct containing variables accessed by shared code 3025 *********************************************************************/ 3026 static int32_t 3027 e1000_copper_link_mgp_setup(struct e1000_hw *hw) 3028 { 3029 int32_t ret_val; 3030 uint16_t phy_data; 3031 3032 DEBUGFUNC(); 3033 3034 if (hw->phy_reset_disable) 3035 return E1000_SUCCESS; 3036 3037 /* Enable CRS on TX. This must be set for half-duplex operation. */ 3038 ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); 3039 if (ret_val) 3040 return ret_val; 3041 3042 phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX; 3043 3044 /* Options: 3045 * MDI/MDI-X = 0 (default) 3046 * 0 - Auto for all speeds 3047 * 1 - MDI mode 3048 * 2 - MDI-X mode 3049 * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes) 3050 */ 3051 phy_data &= ~M88E1000_PSCR_AUTO_X_MODE; 3052 3053 switch (hw->mdix) { 3054 case 1: 3055 phy_data |= M88E1000_PSCR_MDI_MANUAL_MODE; 3056 break; 3057 case 2: 3058 phy_data |= M88E1000_PSCR_MDIX_MANUAL_MODE; 3059 break; 3060 case 3: 3061 phy_data |= M88E1000_PSCR_AUTO_X_1000T; 3062 break; 3063 case 0: 3064 default: 3065 phy_data |= M88E1000_PSCR_AUTO_X_MODE; 3066 break; 3067 } 3068 3069 /* Options: 3070 * disable_polarity_correction = 0 (default) 3071 * Automatic Correction for Reversed Cable Polarity 3072 * 0 - Disabled 3073 * 1 - Enabled 3074 */ 3075 phy_data &= ~M88E1000_PSCR_POLARITY_REVERSAL; 3076 ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data); 3077 if (ret_val) 3078 return ret_val; 3079 3080 if (hw->phy_revision < M88E1011_I_REV_4) { 3081 /* Force TX_CLK in the Extended PHY Specific Control Register 3082 * to 25MHz clock. 3083 */ 3084 ret_val = e1000_read_phy_reg(hw, 3085 M88E1000_EXT_PHY_SPEC_CTRL, &phy_data); 3086 if (ret_val) 3087 return ret_val; 3088 3089 phy_data |= M88E1000_EPSCR_TX_CLK_25; 3090 3091 if ((hw->phy_revision == E1000_REVISION_2) && 3092 (hw->phy_id == M88E1111_I_PHY_ID)) { 3093 /* Vidalia Phy, set the downshift counter to 5x */ 3094 phy_data &= ~(M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK); 3095 phy_data |= M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X; 3096 ret_val = e1000_write_phy_reg(hw, 3097 M88E1000_EXT_PHY_SPEC_CTRL, phy_data); 3098 if (ret_val) 3099 return ret_val; 3100 } else { 3101 /* Configure Master and Slave downshift values */ 3102 phy_data &= ~(M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK 3103 | M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK); 3104 phy_data |= (M88E1000_EPSCR_MASTER_DOWNSHIFT_1X 3105 | M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X); 3106 ret_val = e1000_write_phy_reg(hw, 3107 M88E1000_EXT_PHY_SPEC_CTRL, phy_data); 3108 if (ret_val) 3109 return ret_val; 3110 } 3111 } 3112 3113 /* SW Reset the PHY so all changes take effect */ 3114 ret_val = e1000_phy_reset(hw); 3115 if (ret_val) { 3116 DEBUGOUT("Error Resetting the PHY\n"); 3117 return ret_val; 3118 } 3119 3120 return E1000_SUCCESS; 3121 } 3122 3123 /******************************************************************** 3124 * Setup auto-negotiation and flow control advertisements, 3125 * and then perform auto-negotiation. 3126 * 3127 * hw - Struct containing variables accessed by shared code 3128 *********************************************************************/ 3129 static int32_t 3130 e1000_copper_link_autoneg(struct e1000_hw *hw) 3131 { 3132 int32_t ret_val; 3133 uint16_t phy_data; 3134 3135 DEBUGFUNC(); 3136 3137 /* Perform some bounds checking on the hw->autoneg_advertised 3138 * parameter. If this variable is zero, then set it to the default. 3139 */ 3140 hw->autoneg_advertised &= AUTONEG_ADVERTISE_SPEED_DEFAULT; 3141 3142 /* If autoneg_advertised is zero, we assume it was not defaulted 3143 * by the calling code so we set to advertise full capability. 3144 */ 3145 if (hw->autoneg_advertised == 0) 3146 hw->autoneg_advertised = AUTONEG_ADVERTISE_SPEED_DEFAULT; 3147 3148 /* IFE phy only supports 10/100 */ 3149 if (hw->phy_type == e1000_phy_ife) 3150 hw->autoneg_advertised &= AUTONEG_ADVERTISE_10_100_ALL; 3151 3152 DEBUGOUT("Reconfiguring auto-neg advertisement params\n"); 3153 ret_val = e1000_phy_setup_autoneg(hw); 3154 if (ret_val) { 3155 DEBUGOUT("Error Setting up Auto-Negotiation\n"); 3156 return ret_val; 3157 } 3158 DEBUGOUT("Restarting Auto-Neg\n"); 3159 3160 /* Restart auto-negotiation by setting the Auto Neg Enable bit and 3161 * the Auto Neg Restart bit in the PHY control register. 3162 */ 3163 ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data); 3164 if (ret_val) 3165 return ret_val; 3166 3167 phy_data |= (MII_CR_AUTO_NEG_EN | MII_CR_RESTART_AUTO_NEG); 3168 ret_val = e1000_write_phy_reg(hw, PHY_CTRL, phy_data); 3169 if (ret_val) 3170 return ret_val; 3171 3172 /* Does the user want to wait for Auto-Neg to complete here, or 3173 * check at a later time (for example, callback routine). 3174 */ 3175 /* If we do not wait for autonegtation to complete I 3176 * do not see a valid link status. 3177 * wait_autoneg_complete = 1 . 3178 */ 3179 if (hw->wait_autoneg_complete) { 3180 ret_val = e1000_wait_autoneg(hw); 3181 if (ret_val) { 3182 DEBUGOUT("Error while waiting for autoneg" 3183 "to complete\n"); 3184 return ret_val; 3185 } 3186 } 3187 3188 hw->get_link_status = true; 3189 3190 return E1000_SUCCESS; 3191 } 3192 3193 /****************************************************************************** 3194 * Config the MAC and the PHY after link is up. 3195 * 1) Set up the MAC to the current PHY speed/duplex 3196 * if we are on 82543. If we 3197 * are on newer silicon, we only need to configure 3198 * collision distance in the Transmit Control Register. 3199 * 2) Set up flow control on the MAC to that established with 3200 * the link partner. 3201 * 3) Config DSP to improve Gigabit link quality for some PHY revisions. 3202 * 3203 * hw - Struct containing variables accessed by shared code 3204 ******************************************************************************/ 3205 static int32_t 3206 e1000_copper_link_postconfig(struct e1000_hw *hw) 3207 { 3208 int32_t ret_val; 3209 DEBUGFUNC(); 3210 3211 if (hw->mac_type >= e1000_82544) { 3212 e1000_config_collision_dist(hw); 3213 } else { 3214 ret_val = e1000_config_mac_to_phy(hw); 3215 if (ret_val) { 3216 DEBUGOUT("Error configuring MAC to PHY settings\n"); 3217 return ret_val; 3218 } 3219 } 3220 ret_val = e1000_config_fc_after_link_up(hw); 3221 if (ret_val) { 3222 DEBUGOUT("Error Configuring Flow Control\n"); 3223 return ret_val; 3224 } 3225 return E1000_SUCCESS; 3226 } 3227 3228 /****************************************************************************** 3229 * Detects which PHY is present and setup the speed and duplex 3230 * 3231 * hw - Struct containing variables accessed by shared code 3232 ******************************************************************************/ 3233 static int 3234 e1000_setup_copper_link(struct e1000_hw *hw) 3235 { 3236 int32_t ret_val; 3237 uint16_t i; 3238 uint16_t phy_data; 3239 uint16_t reg_data; 3240 3241 DEBUGFUNC(); 3242 3243 switch (hw->mac_type) { 3244 case e1000_80003es2lan: 3245 case e1000_ich8lan: 3246 /* Set the mac to wait the maximum time between each 3247 * iteration and increase the max iterations when 3248 * polling the phy; this fixes erroneous timeouts at 10Mbps. */ 3249 ret_val = e1000_write_kmrn_reg(hw, 3250 GG82563_REG(0x34, 4), 0xFFFF); 3251 if (ret_val) 3252 return ret_val; 3253 ret_val = e1000_read_kmrn_reg(hw, 3254 GG82563_REG(0x34, 9), ®_data); 3255 if (ret_val) 3256 return ret_val; 3257 reg_data |= 0x3F; 3258 ret_val = e1000_write_kmrn_reg(hw, 3259 GG82563_REG(0x34, 9), reg_data); 3260 if (ret_val) 3261 return ret_val; 3262 default: 3263 break; 3264 } 3265 3266 /* Check if it is a valid PHY and set PHY mode if necessary. */ 3267 ret_val = e1000_copper_link_preconfig(hw); 3268 if (ret_val) 3269 return ret_val; 3270 switch (hw->mac_type) { 3271 case e1000_80003es2lan: 3272 /* Kumeran registers are written-only */ 3273 reg_data = 3274 E1000_KUMCTRLSTA_INB_CTRL_LINK_STATUS_TX_TIMEOUT_DEFAULT; 3275 reg_data |= E1000_KUMCTRLSTA_INB_CTRL_DIS_PADDING; 3276 ret_val = e1000_write_kmrn_reg(hw, 3277 E1000_KUMCTRLSTA_OFFSET_INB_CTRL, reg_data); 3278 if (ret_val) 3279 return ret_val; 3280 break; 3281 default: 3282 break; 3283 } 3284 3285 if (hw->phy_type == e1000_phy_igp || 3286 hw->phy_type == e1000_phy_igp_3 || 3287 hw->phy_type == e1000_phy_igp_2) { 3288 ret_val = e1000_copper_link_igp_setup(hw); 3289 if (ret_val) 3290 return ret_val; 3291 } else if (hw->phy_type == e1000_phy_m88 || 3292 hw->phy_type == e1000_phy_igb) { 3293 ret_val = e1000_copper_link_mgp_setup(hw); 3294 if (ret_val) 3295 return ret_val; 3296 } else if (hw->phy_type == e1000_phy_gg82563) { 3297 ret_val = e1000_copper_link_ggp_setup(hw); 3298 if (ret_val) 3299 return ret_val; 3300 } 3301 3302 /* always auto */ 3303 /* Setup autoneg and flow control advertisement 3304 * and perform autonegotiation */ 3305 ret_val = e1000_copper_link_autoneg(hw); 3306 if (ret_val) 3307 return ret_val; 3308 3309 /* Check link status. Wait up to 100 microseconds for link to become 3310 * valid. 3311 */ 3312 for (i = 0; i < 10; i++) { 3313 ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data); 3314 if (ret_val) 3315 return ret_val; 3316 ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data); 3317 if (ret_val) 3318 return ret_val; 3319 3320 if (phy_data & MII_SR_LINK_STATUS) { 3321 /* Config the MAC and PHY after link is up */ 3322 ret_val = e1000_copper_link_postconfig(hw); 3323 if (ret_val) 3324 return ret_val; 3325 3326 DEBUGOUT("Valid link established!!!\n"); 3327 return E1000_SUCCESS; 3328 } 3329 udelay(10); 3330 } 3331 3332 DEBUGOUT("Unable to establish link!!!\n"); 3333 return E1000_SUCCESS; 3334 } 3335 3336 /****************************************************************************** 3337 * Configures PHY autoneg and flow control advertisement settings 3338 * 3339 * hw - Struct containing variables accessed by shared code 3340 ******************************************************************************/ 3341 int32_t 3342 e1000_phy_setup_autoneg(struct e1000_hw *hw) 3343 { 3344 int32_t ret_val; 3345 uint16_t mii_autoneg_adv_reg; 3346 uint16_t mii_1000t_ctrl_reg; 3347 3348 DEBUGFUNC(); 3349 3350 /* Read the MII Auto-Neg Advertisement Register (Address 4). */ 3351 ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_ADV, &mii_autoneg_adv_reg); 3352 if (ret_val) 3353 return ret_val; 3354 3355 if (hw->phy_type != e1000_phy_ife) { 3356 /* Read the MII 1000Base-T Control Register (Address 9). */ 3357 ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, 3358 &mii_1000t_ctrl_reg); 3359 if (ret_val) 3360 return ret_val; 3361 } else 3362 mii_1000t_ctrl_reg = 0; 3363 3364 /* Need to parse both autoneg_advertised and fc and set up 3365 * the appropriate PHY registers. First we will parse for 3366 * autoneg_advertised software override. Since we can advertise 3367 * a plethora of combinations, we need to check each bit 3368 * individually. 3369 */ 3370 3371 /* First we clear all the 10/100 mb speed bits in the Auto-Neg 3372 * Advertisement Register (Address 4) and the 1000 mb speed bits in 3373 * the 1000Base-T Control Register (Address 9). 3374 */ 3375 mii_autoneg_adv_reg &= ~REG4_SPEED_MASK; 3376 mii_1000t_ctrl_reg &= ~REG9_SPEED_MASK; 3377 3378 DEBUGOUT("autoneg_advertised %x\n", hw->autoneg_advertised); 3379 3380 /* Do we want to advertise 10 Mb Half Duplex? */ 3381 if (hw->autoneg_advertised & ADVERTISE_10_HALF) { 3382 DEBUGOUT("Advertise 10mb Half duplex\n"); 3383 mii_autoneg_adv_reg |= NWAY_AR_10T_HD_CAPS; 3384 } 3385 3386 /* Do we want to advertise 10 Mb Full Duplex? */ 3387 if (hw->autoneg_advertised & ADVERTISE_10_FULL) { 3388 DEBUGOUT("Advertise 10mb Full duplex\n"); 3389 mii_autoneg_adv_reg |= NWAY_AR_10T_FD_CAPS; 3390 } 3391 3392 /* Do we want to advertise 100 Mb Half Duplex? */ 3393 if (hw->autoneg_advertised & ADVERTISE_100_HALF) { 3394 DEBUGOUT("Advertise 100mb Half duplex\n"); 3395 mii_autoneg_adv_reg |= NWAY_AR_100TX_HD_CAPS; 3396 } 3397 3398 /* Do we want to advertise 100 Mb Full Duplex? */ 3399 if (hw->autoneg_advertised & ADVERTISE_100_FULL) { 3400 DEBUGOUT("Advertise 100mb Full duplex\n"); 3401 mii_autoneg_adv_reg |= NWAY_AR_100TX_FD_CAPS; 3402 } 3403 3404 /* We do not allow the Phy to advertise 1000 Mb Half Duplex */ 3405 if (hw->autoneg_advertised & ADVERTISE_1000_HALF) { 3406 DEBUGOUT 3407 ("Advertise 1000mb Half duplex requested, request denied!\n"); 3408 } 3409 3410 /* Do we want to advertise 1000 Mb Full Duplex? */ 3411 if (hw->autoneg_advertised & ADVERTISE_1000_FULL) { 3412 DEBUGOUT("Advertise 1000mb Full duplex\n"); 3413 mii_1000t_ctrl_reg |= CR_1000T_FD_CAPS; 3414 } 3415 3416 /* Check for a software override of the flow control settings, and 3417 * setup the PHY advertisement registers accordingly. If 3418 * auto-negotiation is enabled, then software will have to set the 3419 * "PAUSE" bits to the correct value in the Auto-Negotiation 3420 * Advertisement Register (PHY_AUTONEG_ADV) and re-start auto-negotiation. 3421 * 3422 * The possible values of the "fc" parameter are: 3423 * 0: Flow control is completely disabled 3424 * 1: Rx flow control is enabled (we can receive pause frames 3425 * but not send pause frames). 3426 * 2: Tx flow control is enabled (we can send pause frames 3427 * but we do not support receiving pause frames). 3428 * 3: Both Rx and TX flow control (symmetric) are enabled. 3429 * other: No software override. The flow control configuration 3430 * in the EEPROM is used. 3431 */ 3432 switch (hw->fc) { 3433 case e1000_fc_none: /* 0 */ 3434 /* Flow control (RX & TX) is completely disabled by a 3435 * software over-ride. 3436 */ 3437 mii_autoneg_adv_reg &= ~(NWAY_AR_ASM_DIR | NWAY_AR_PAUSE); 3438 break; 3439 case e1000_fc_rx_pause: /* 1 */ 3440 /* RX Flow control is enabled, and TX Flow control is 3441 * disabled, by a software over-ride. 3442 */ 3443 /* Since there really isn't a way to advertise that we are 3444 * capable of RX Pause ONLY, we will advertise that we 3445 * support both symmetric and asymmetric RX PAUSE. Later 3446 * (in e1000_config_fc_after_link_up) we will disable the 3447 *hw's ability to send PAUSE frames. 3448 */ 3449 mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE); 3450 break; 3451 case e1000_fc_tx_pause: /* 2 */ 3452 /* TX Flow control is enabled, and RX Flow control is 3453 * disabled, by a software over-ride. 3454 */ 3455 mii_autoneg_adv_reg |= NWAY_AR_ASM_DIR; 3456 mii_autoneg_adv_reg &= ~NWAY_AR_PAUSE; 3457 break; 3458 case e1000_fc_full: /* 3 */ 3459 /* Flow control (both RX and TX) is enabled by a software 3460 * over-ride. 3461 */ 3462 mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE); 3463 break; 3464 default: 3465 DEBUGOUT("Flow control param set incorrectly\n"); 3466 return -E1000_ERR_CONFIG; 3467 } 3468 3469 ret_val = e1000_write_phy_reg(hw, PHY_AUTONEG_ADV, mii_autoneg_adv_reg); 3470 if (ret_val) 3471 return ret_val; 3472 3473 DEBUGOUT("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg); 3474 3475 if (hw->phy_type != e1000_phy_ife) { 3476 ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, 3477 mii_1000t_ctrl_reg); 3478 if (ret_val) 3479 return ret_val; 3480 } 3481 3482 return E1000_SUCCESS; 3483 } 3484 3485 /****************************************************************************** 3486 * Sets the collision distance in the Transmit Control register 3487 * 3488 * hw - Struct containing variables accessed by shared code 3489 * 3490 * Link should have been established previously. Reads the speed and duplex 3491 * information from the Device Status register. 3492 ******************************************************************************/ 3493 static void 3494 e1000_config_collision_dist(struct e1000_hw *hw) 3495 { 3496 uint32_t tctl, coll_dist; 3497 3498 DEBUGFUNC(); 3499 3500 if (hw->mac_type < e1000_82543) 3501 coll_dist = E1000_COLLISION_DISTANCE_82542; 3502 else 3503 coll_dist = E1000_COLLISION_DISTANCE; 3504 3505 tctl = E1000_READ_REG(hw, TCTL); 3506 3507 tctl &= ~E1000_TCTL_COLD; 3508 tctl |= coll_dist << E1000_COLD_SHIFT; 3509 3510 E1000_WRITE_REG(hw, TCTL, tctl); 3511 E1000_WRITE_FLUSH(hw); 3512 } 3513 3514 /****************************************************************************** 3515 * Sets MAC speed and duplex settings to reflect the those in the PHY 3516 * 3517 * hw - Struct containing variables accessed by shared code 3518 * mii_reg - data to write to the MII control register 3519 * 3520 * The contents of the PHY register containing the needed information need to 3521 * be passed in. 3522 ******************************************************************************/ 3523 static int 3524 e1000_config_mac_to_phy(struct e1000_hw *hw) 3525 { 3526 uint32_t ctrl; 3527 uint16_t phy_data; 3528 3529 DEBUGFUNC(); 3530 3531 /* Read the Device Control Register and set the bits to Force Speed 3532 * and Duplex. 3533 */ 3534 ctrl = E1000_READ_REG(hw, CTRL); 3535 ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); 3536 ctrl &= ~(E1000_CTRL_ILOS); 3537 ctrl |= (E1000_CTRL_SPD_SEL); 3538 3539 /* Set up duplex in the Device Control and Transmit Control 3540 * registers depending on negotiated values. 3541 */ 3542 if (e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data) < 0) { 3543 DEBUGOUT("PHY Read Error\n"); 3544 return -E1000_ERR_PHY; 3545 } 3546 if (phy_data & M88E1000_PSSR_DPLX) 3547 ctrl |= E1000_CTRL_FD; 3548 else 3549 ctrl &= ~E1000_CTRL_FD; 3550 3551 e1000_config_collision_dist(hw); 3552 3553 /* Set up speed in the Device Control register depending on 3554 * negotiated values. 3555 */ 3556 if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS) 3557 ctrl |= E1000_CTRL_SPD_1000; 3558 else if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_100MBS) 3559 ctrl |= E1000_CTRL_SPD_100; 3560 /* Write the configured values back to the Device Control Reg. */ 3561 E1000_WRITE_REG(hw, CTRL, ctrl); 3562 return 0; 3563 } 3564 3565 /****************************************************************************** 3566 * Forces the MAC's flow control settings. 3567 * 3568 * hw - Struct containing variables accessed by shared code 3569 * 3570 * Sets the TFCE and RFCE bits in the device control register to reflect 3571 * the adapter settings. TFCE and RFCE need to be explicitly set by 3572 * software when a Copper PHY is used because autonegotiation is managed 3573 * by the PHY rather than the MAC. Software must also configure these 3574 * bits when link is forced on a fiber connection. 3575 *****************************************************************************/ 3576 static int 3577 e1000_force_mac_fc(struct e1000_hw *hw) 3578 { 3579 uint32_t ctrl; 3580 3581 DEBUGFUNC(); 3582 3583 /* Get the current configuration of the Device Control Register */ 3584 ctrl = E1000_READ_REG(hw, CTRL); 3585 3586 /* Because we didn't get link via the internal auto-negotiation 3587 * mechanism (we either forced link or we got link via PHY 3588 * auto-neg), we have to manually enable/disable transmit an 3589 * receive flow control. 3590 * 3591 * The "Case" statement below enables/disable flow control 3592 * according to the "hw->fc" parameter. 3593 * 3594 * The possible values of the "fc" parameter are: 3595 * 0: Flow control is completely disabled 3596 * 1: Rx flow control is enabled (we can receive pause 3597 * frames but not send pause frames). 3598 * 2: Tx flow control is enabled (we can send pause frames 3599 * frames but we do not receive pause frames). 3600 * 3: Both Rx and TX flow control (symmetric) is enabled. 3601 * other: No other values should be possible at this point. 3602 */ 3603 3604 switch (hw->fc) { 3605 case e1000_fc_none: 3606 ctrl &= (~(E1000_CTRL_TFCE | E1000_CTRL_RFCE)); 3607 break; 3608 case e1000_fc_rx_pause: 3609 ctrl &= (~E1000_CTRL_TFCE); 3610 ctrl |= E1000_CTRL_RFCE; 3611 break; 3612 case e1000_fc_tx_pause: 3613 ctrl &= (~E1000_CTRL_RFCE); 3614 ctrl |= E1000_CTRL_TFCE; 3615 break; 3616 case e1000_fc_full: 3617 ctrl |= (E1000_CTRL_TFCE | E1000_CTRL_RFCE); 3618 break; 3619 default: 3620 DEBUGOUT("Flow control param set incorrectly\n"); 3621 return -E1000_ERR_CONFIG; 3622 } 3623 3624 /* Disable TX Flow Control for 82542 (rev 2.0) */ 3625 if (hw->mac_type == e1000_82542_rev2_0) 3626 ctrl &= (~E1000_CTRL_TFCE); 3627 3628 E1000_WRITE_REG(hw, CTRL, ctrl); 3629 return 0; 3630 } 3631 3632 /****************************************************************************** 3633 * Configures flow control settings after link is established 3634 * 3635 * hw - Struct containing variables accessed by shared code 3636 * 3637 * Should be called immediately after a valid link has been established. 3638 * Forces MAC flow control settings if link was forced. When in MII/GMII mode 3639 * and autonegotiation is enabled, the MAC flow control settings will be set 3640 * based on the flow control negotiated by the PHY. In TBI mode, the TFCE 3641 * and RFCE bits will be automaticaly set to the negotiated flow control mode. 3642 *****************************************************************************/ 3643 static int32_t 3644 e1000_config_fc_after_link_up(struct e1000_hw *hw) 3645 { 3646 int32_t ret_val; 3647 uint16_t mii_status_reg; 3648 uint16_t mii_nway_adv_reg; 3649 uint16_t mii_nway_lp_ability_reg; 3650 uint16_t speed; 3651 uint16_t duplex; 3652 3653 DEBUGFUNC(); 3654 3655 /* Check for the case where we have fiber media and auto-neg failed 3656 * so we had to force link. In this case, we need to force the 3657 * configuration of the MAC to match the "fc" parameter. 3658 */ 3659 if (((hw->media_type == e1000_media_type_fiber) && (hw->autoneg_failed)) 3660 || ((hw->media_type == e1000_media_type_internal_serdes) 3661 && (hw->autoneg_failed)) 3662 || ((hw->media_type == e1000_media_type_copper) 3663 && (!hw->autoneg))) { 3664 ret_val = e1000_force_mac_fc(hw); 3665 if (ret_val < 0) { 3666 DEBUGOUT("Error forcing flow control settings\n"); 3667 return ret_val; 3668 } 3669 } 3670 3671 /* Check for the case where we have copper media and auto-neg is 3672 * enabled. In this case, we need to check and see if Auto-Neg 3673 * has completed, and if so, how the PHY and link partner has 3674 * flow control configured. 3675 */ 3676 if (hw->media_type == e1000_media_type_copper) { 3677 /* Read the MII Status Register and check to see if AutoNeg 3678 * has completed. We read this twice because this reg has 3679 * some "sticky" (latched) bits. 3680 */ 3681 if (e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg) < 0) { 3682 DEBUGOUT("PHY Read Error\n"); 3683 return -E1000_ERR_PHY; 3684 } 3685 if (e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg) < 0) { 3686 DEBUGOUT("PHY Read Error\n"); 3687 return -E1000_ERR_PHY; 3688 } 3689 3690 if (mii_status_reg & MII_SR_AUTONEG_COMPLETE) { 3691 /* The AutoNeg process has completed, so we now need to 3692 * read both the Auto Negotiation Advertisement Register 3693 * (Address 4) and the Auto_Negotiation Base Page Ability 3694 * Register (Address 5) to determine how flow control was 3695 * negotiated. 3696 */ 3697 if (e1000_read_phy_reg 3698 (hw, PHY_AUTONEG_ADV, &mii_nway_adv_reg) < 0) { 3699 DEBUGOUT("PHY Read Error\n"); 3700 return -E1000_ERR_PHY; 3701 } 3702 if (e1000_read_phy_reg 3703 (hw, PHY_LP_ABILITY, 3704 &mii_nway_lp_ability_reg) < 0) { 3705 DEBUGOUT("PHY Read Error\n"); 3706 return -E1000_ERR_PHY; 3707 } 3708 3709 /* Two bits in the Auto Negotiation Advertisement Register 3710 * (Address 4) and two bits in the Auto Negotiation Base 3711 * Page Ability Register (Address 5) determine flow control 3712 * for both the PHY and the link partner. The following 3713 * table, taken out of the IEEE 802.3ab/D6.0 dated March 25, 3714 * 1999, describes these PAUSE resolution bits and how flow 3715 * control is determined based upon these settings. 3716 * NOTE: DC = Don't Care 3717 * 3718 * LOCAL DEVICE | LINK PARTNER 3719 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | NIC Resolution 3720 *-------|---------|-------|---------|-------------------- 3721 * 0 | 0 | DC | DC | e1000_fc_none 3722 * 0 | 1 | 0 | DC | e1000_fc_none 3723 * 0 | 1 | 1 | 0 | e1000_fc_none 3724 * 0 | 1 | 1 | 1 | e1000_fc_tx_pause 3725 * 1 | 0 | 0 | DC | e1000_fc_none 3726 * 1 | DC | 1 | DC | e1000_fc_full 3727 * 1 | 1 | 0 | 0 | e1000_fc_none 3728 * 1 | 1 | 0 | 1 | e1000_fc_rx_pause 3729 * 3730 */ 3731 /* Are both PAUSE bits set to 1? If so, this implies 3732 * Symmetric Flow Control is enabled at both ends. The 3733 * ASM_DIR bits are irrelevant per the spec. 3734 * 3735 * For Symmetric Flow Control: 3736 * 3737 * LOCAL DEVICE | LINK PARTNER 3738 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result 3739 *-------|---------|-------|---------|-------------------- 3740 * 1 | DC | 1 | DC | e1000_fc_full 3741 * 3742 */ 3743 if ((mii_nway_adv_reg & NWAY_AR_PAUSE) && 3744 (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE)) { 3745 /* Now we need to check if the user selected RX ONLY 3746 * of pause frames. In this case, we had to advertise 3747 * FULL flow control because we could not advertise RX 3748 * ONLY. Hence, we must now check to see if we need to 3749 * turn OFF the TRANSMISSION of PAUSE frames. 3750 */ 3751 if (hw->original_fc == e1000_fc_full) { 3752 hw->fc = e1000_fc_full; 3753 DEBUGOUT("Flow Control = FULL.\r\n"); 3754 } else { 3755 hw->fc = e1000_fc_rx_pause; 3756 DEBUGOUT 3757 ("Flow Control = RX PAUSE frames only.\r\n"); 3758 } 3759 } 3760 /* For receiving PAUSE frames ONLY. 3761 * 3762 * LOCAL DEVICE | LINK PARTNER 3763 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result 3764 *-------|---------|-------|---------|-------------------- 3765 * 0 | 1 | 1 | 1 | e1000_fc_tx_pause 3766 * 3767 */ 3768 else if (!(mii_nway_adv_reg & NWAY_AR_PAUSE) && 3769 (mii_nway_adv_reg & NWAY_AR_ASM_DIR) && 3770 (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) && 3771 (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) 3772 { 3773 hw->fc = e1000_fc_tx_pause; 3774 DEBUGOUT 3775 ("Flow Control = TX PAUSE frames only.\r\n"); 3776 } 3777 /* For transmitting PAUSE frames ONLY. 3778 * 3779 * LOCAL DEVICE | LINK PARTNER 3780 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result 3781 *-------|---------|-------|---------|-------------------- 3782 * 1 | 1 | 0 | 1 | e1000_fc_rx_pause 3783 * 3784 */ 3785 else if ((mii_nway_adv_reg & NWAY_AR_PAUSE) && 3786 (mii_nway_adv_reg & NWAY_AR_ASM_DIR) && 3787 !(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) && 3788 (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) 3789 { 3790 hw->fc = e1000_fc_rx_pause; 3791 DEBUGOUT 3792 ("Flow Control = RX PAUSE frames only.\r\n"); 3793 } 3794 /* Per the IEEE spec, at this point flow control should be 3795 * disabled. However, we want to consider that we could 3796 * be connected to a legacy switch that doesn't advertise 3797 * desired flow control, but can be forced on the link 3798 * partner. So if we advertised no flow control, that is 3799 * what we will resolve to. If we advertised some kind of 3800 * receive capability (Rx Pause Only or Full Flow Control) 3801 * and the link partner advertised none, we will configure 3802 * ourselves to enable Rx Flow Control only. We can do 3803 * this safely for two reasons: If the link partner really 3804 * didn't want flow control enabled, and we enable Rx, no 3805 * harm done since we won't be receiving any PAUSE frames 3806 * anyway. If the intent on the link partner was to have 3807 * flow control enabled, then by us enabling RX only, we 3808 * can at least receive pause frames and process them. 3809 * This is a good idea because in most cases, since we are 3810 * predominantly a server NIC, more times than not we will 3811 * be asked to delay transmission of packets than asking 3812 * our link partner to pause transmission of frames. 3813 */ 3814 else if (hw->original_fc == e1000_fc_none || 3815 hw->original_fc == e1000_fc_tx_pause) { 3816 hw->fc = e1000_fc_none; 3817 DEBUGOUT("Flow Control = NONE.\r\n"); 3818 } else { 3819 hw->fc = e1000_fc_rx_pause; 3820 DEBUGOUT 3821 ("Flow Control = RX PAUSE frames only.\r\n"); 3822 } 3823 3824 /* Now we need to do one last check... If we auto- 3825 * negotiated to HALF DUPLEX, flow control should not be 3826 * enabled per IEEE 802.3 spec. 3827 */ 3828 e1000_get_speed_and_duplex(hw, &speed, &duplex); 3829 3830 if (duplex == HALF_DUPLEX) 3831 hw->fc = e1000_fc_none; 3832 3833 /* Now we call a subroutine to actually force the MAC 3834 * controller to use the correct flow control settings. 3835 */ 3836 ret_val = e1000_force_mac_fc(hw); 3837 if (ret_val < 0) { 3838 DEBUGOUT 3839 ("Error forcing flow control settings\n"); 3840 return ret_val; 3841 } 3842 } else { 3843 DEBUGOUT 3844 ("Copper PHY and Auto Neg has not completed.\r\n"); 3845 } 3846 } 3847 return E1000_SUCCESS; 3848 } 3849 3850 /****************************************************************************** 3851 * Checks to see if the link status of the hardware has changed. 3852 * 3853 * hw - Struct containing variables accessed by shared code 3854 * 3855 * Called by any function that needs to check the link status of the adapter. 3856 *****************************************************************************/ 3857 static int 3858 e1000_check_for_link(struct e1000_hw *hw) 3859 { 3860 uint32_t rxcw; 3861 uint32_t ctrl; 3862 uint32_t status; 3863 uint32_t rctl; 3864 uint32_t signal; 3865 int32_t ret_val; 3866 uint16_t phy_data; 3867 uint16_t lp_capability; 3868 3869 DEBUGFUNC(); 3870 3871 /* On adapters with a MAC newer that 82544, SW Defineable pin 1 will be 3872 * set when the optics detect a signal. On older adapters, it will be 3873 * cleared when there is a signal 3874 */ 3875 ctrl = E1000_READ_REG(hw, CTRL); 3876 if ((hw->mac_type > e1000_82544) && !(ctrl & E1000_CTRL_ILOS)) 3877 signal = E1000_CTRL_SWDPIN1; 3878 else 3879 signal = 0; 3880 3881 status = E1000_READ_REG(hw, STATUS); 3882 rxcw = E1000_READ_REG(hw, RXCW); 3883 DEBUGOUT("ctrl: %#08x status %#08x rxcw %#08x\n", ctrl, status, rxcw); 3884 3885 /* If we have a copper PHY then we only want to go out to the PHY 3886 * registers to see if Auto-Neg has completed and/or if our link 3887 * status has changed. The get_link_status flag will be set if we 3888 * receive a Link Status Change interrupt or we have Rx Sequence 3889 * Errors. 3890 */ 3891 if ((hw->media_type == e1000_media_type_copper) && hw->get_link_status) { 3892 /* First we want to see if the MII Status Register reports 3893 * link. If so, then we want to get the current speed/duplex 3894 * of the PHY. 3895 * Read the register twice since the link bit is sticky. 3896 */ 3897 if (e1000_read_phy_reg(hw, PHY_STATUS, &phy_data) < 0) { 3898 DEBUGOUT("PHY Read Error\n"); 3899 return -E1000_ERR_PHY; 3900 } 3901 if (e1000_read_phy_reg(hw, PHY_STATUS, &phy_data) < 0) { 3902 DEBUGOUT("PHY Read Error\n"); 3903 return -E1000_ERR_PHY; 3904 } 3905 3906 if (phy_data & MII_SR_LINK_STATUS) { 3907 hw->get_link_status = false; 3908 } else { 3909 /* No link detected */ 3910 return -E1000_ERR_NOLINK; 3911 } 3912 3913 /* We have a M88E1000 PHY and Auto-Neg is enabled. If we 3914 * have Si on board that is 82544 or newer, Auto 3915 * Speed Detection takes care of MAC speed/duplex 3916 * configuration. So we only need to configure Collision 3917 * Distance in the MAC. Otherwise, we need to force 3918 * speed/duplex on the MAC to the current PHY speed/duplex 3919 * settings. 3920 */ 3921 if (hw->mac_type >= e1000_82544) 3922 e1000_config_collision_dist(hw); 3923 else { 3924 ret_val = e1000_config_mac_to_phy(hw); 3925 if (ret_val < 0) { 3926 DEBUGOUT 3927 ("Error configuring MAC to PHY settings\n"); 3928 return ret_val; 3929 } 3930 } 3931 3932 /* Configure Flow Control now that Auto-Neg has completed. First, we 3933 * need to restore the desired flow control settings because we may 3934 * have had to re-autoneg with a different link partner. 3935 */ 3936 ret_val = e1000_config_fc_after_link_up(hw); 3937 if (ret_val < 0) { 3938 DEBUGOUT("Error configuring flow control\n"); 3939 return ret_val; 3940 } 3941 3942 /* At this point we know that we are on copper and we have 3943 * auto-negotiated link. These are conditions for checking the link 3944 * parter capability register. We use the link partner capability to 3945 * determine if TBI Compatibility needs to be turned on or off. If 3946 * the link partner advertises any speed in addition to Gigabit, then 3947 * we assume that they are GMII-based, and TBI compatibility is not 3948 * needed. If no other speeds are advertised, we assume the link 3949 * partner is TBI-based, and we turn on TBI Compatibility. 3950 */ 3951 if (hw->tbi_compatibility_en) { 3952 if (e1000_read_phy_reg 3953 (hw, PHY_LP_ABILITY, &lp_capability) < 0) { 3954 DEBUGOUT("PHY Read Error\n"); 3955 return -E1000_ERR_PHY; 3956 } 3957 if (lp_capability & (NWAY_LPAR_10T_HD_CAPS | 3958 NWAY_LPAR_10T_FD_CAPS | 3959 NWAY_LPAR_100TX_HD_CAPS | 3960 NWAY_LPAR_100TX_FD_CAPS | 3961 NWAY_LPAR_100T4_CAPS)) { 3962 /* If our link partner advertises anything in addition to 3963 * gigabit, we do not need to enable TBI compatibility. 3964 */ 3965 if (hw->tbi_compatibility_on) { 3966 /* If we previously were in the mode, turn it off. */ 3967 rctl = E1000_READ_REG(hw, RCTL); 3968 rctl &= ~E1000_RCTL_SBP; 3969 E1000_WRITE_REG(hw, RCTL, rctl); 3970 hw->tbi_compatibility_on = false; 3971 } 3972 } else { 3973 /* If TBI compatibility is was previously off, turn it on. For 3974 * compatibility with a TBI link partner, we will store bad 3975 * packets. Some frames have an additional byte on the end and 3976 * will look like CRC errors to to the hardware. 3977 */ 3978 if (!hw->tbi_compatibility_on) { 3979 hw->tbi_compatibility_on = true; 3980 rctl = E1000_READ_REG(hw, RCTL); 3981 rctl |= E1000_RCTL_SBP; 3982 E1000_WRITE_REG(hw, RCTL, rctl); 3983 } 3984 } 3985 } 3986 } 3987 /* If we don't have link (auto-negotiation failed or link partner cannot 3988 * auto-negotiate), the cable is plugged in (we have signal), and our 3989 * link partner is not trying to auto-negotiate with us (we are receiving 3990 * idles or data), we need to force link up. We also need to give 3991 * auto-negotiation time to complete, in case the cable was just plugged 3992 * in. The autoneg_failed flag does this. 3993 */ 3994 else if ((hw->media_type == e1000_media_type_fiber) && 3995 (!(status & E1000_STATUS_LU)) && 3996 ((ctrl & E1000_CTRL_SWDPIN1) == signal) && 3997 (!(rxcw & E1000_RXCW_C))) { 3998 if (hw->autoneg_failed == 0) { 3999 hw->autoneg_failed = 1; 4000 return 0; 4001 } 4002 DEBUGOUT("NOT RXing /C/, disable AutoNeg and force link.\r\n"); 4003 4004 /* Disable auto-negotiation in the TXCW register */ 4005 E1000_WRITE_REG(hw, TXCW, (hw->txcw & ~E1000_TXCW_ANE)); 4006 4007 /* Force link-up and also force full-duplex. */ 4008 ctrl = E1000_READ_REG(hw, CTRL); 4009 ctrl |= (E1000_CTRL_SLU | E1000_CTRL_FD); 4010 E1000_WRITE_REG(hw, CTRL, ctrl); 4011 4012 /* Configure Flow Control after forcing link up. */ 4013 ret_val = e1000_config_fc_after_link_up(hw); 4014 if (ret_val < 0) { 4015 DEBUGOUT("Error configuring flow control\n"); 4016 return ret_val; 4017 } 4018 } 4019 /* If we are forcing link and we are receiving /C/ ordered sets, re-enable 4020 * auto-negotiation in the TXCW register and disable forced link in the 4021 * Device Control register in an attempt to auto-negotiate with our link 4022 * partner. 4023 */ 4024 else if ((hw->media_type == e1000_media_type_fiber) && 4025 (ctrl & E1000_CTRL_SLU) && (rxcw & E1000_RXCW_C)) { 4026 DEBUGOUT 4027 ("RXing /C/, enable AutoNeg and stop forcing link.\r\n"); 4028 E1000_WRITE_REG(hw, TXCW, hw->txcw); 4029 E1000_WRITE_REG(hw, CTRL, (ctrl & ~E1000_CTRL_SLU)); 4030 } 4031 return 0; 4032 } 4033 4034 /****************************************************************************** 4035 * Configure the MAC-to-PHY interface for 10/100Mbps 4036 * 4037 * hw - Struct containing variables accessed by shared code 4038 ******************************************************************************/ 4039 static int32_t 4040 e1000_configure_kmrn_for_10_100(struct e1000_hw *hw, uint16_t duplex) 4041 { 4042 int32_t ret_val = E1000_SUCCESS; 4043 uint32_t tipg; 4044 uint16_t reg_data; 4045 4046 DEBUGFUNC(); 4047 4048 reg_data = E1000_KUMCTRLSTA_HD_CTRL_10_100_DEFAULT; 4049 ret_val = e1000_write_kmrn_reg(hw, 4050 E1000_KUMCTRLSTA_OFFSET_HD_CTRL, reg_data); 4051 if (ret_val) 4052 return ret_val; 4053 4054 /* Configure Transmit Inter-Packet Gap */ 4055 tipg = E1000_READ_REG(hw, TIPG); 4056 tipg &= ~E1000_TIPG_IPGT_MASK; 4057 tipg |= DEFAULT_80003ES2LAN_TIPG_IPGT_10_100; 4058 E1000_WRITE_REG(hw, TIPG, tipg); 4059 4060 ret_val = e1000_read_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, ®_data); 4061 4062 if (ret_val) 4063 return ret_val; 4064 4065 if (duplex == HALF_DUPLEX) 4066 reg_data |= GG82563_KMCR_PASS_FALSE_CARRIER; 4067 else 4068 reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER; 4069 4070 ret_val = e1000_write_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data); 4071 4072 return ret_val; 4073 } 4074 4075 static int32_t 4076 e1000_configure_kmrn_for_1000(struct e1000_hw *hw) 4077 { 4078 int32_t ret_val = E1000_SUCCESS; 4079 uint16_t reg_data; 4080 uint32_t tipg; 4081 4082 DEBUGFUNC(); 4083 4084 reg_data = E1000_KUMCTRLSTA_HD_CTRL_1000_DEFAULT; 4085 ret_val = e1000_write_kmrn_reg(hw, 4086 E1000_KUMCTRLSTA_OFFSET_HD_CTRL, reg_data); 4087 if (ret_val) 4088 return ret_val; 4089 4090 /* Configure Transmit Inter-Packet Gap */ 4091 tipg = E1000_READ_REG(hw, TIPG); 4092 tipg &= ~E1000_TIPG_IPGT_MASK; 4093 tipg |= DEFAULT_80003ES2LAN_TIPG_IPGT_1000; 4094 E1000_WRITE_REG(hw, TIPG, tipg); 4095 4096 ret_val = e1000_read_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, ®_data); 4097 4098 if (ret_val) 4099 return ret_val; 4100 4101 reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER; 4102 ret_val = e1000_write_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data); 4103 4104 return ret_val; 4105 } 4106 4107 /****************************************************************************** 4108 * Detects the current speed and duplex settings of the hardware. 4109 * 4110 * hw - Struct containing variables accessed by shared code 4111 * speed - Speed of the connection 4112 * duplex - Duplex setting of the connection 4113 *****************************************************************************/ 4114 static int 4115 e1000_get_speed_and_duplex(struct e1000_hw *hw, uint16_t *speed, 4116 uint16_t *duplex) 4117 { 4118 uint32_t status; 4119 int32_t ret_val; 4120 uint16_t phy_data; 4121 4122 DEBUGFUNC(); 4123 4124 if (hw->mac_type >= e1000_82543) { 4125 status = E1000_READ_REG(hw, STATUS); 4126 if (status & E1000_STATUS_SPEED_1000) { 4127 *speed = SPEED_1000; 4128 DEBUGOUT("1000 Mbs, "); 4129 } else if (status & E1000_STATUS_SPEED_100) { 4130 *speed = SPEED_100; 4131 DEBUGOUT("100 Mbs, "); 4132 } else { 4133 *speed = SPEED_10; 4134 DEBUGOUT("10 Mbs, "); 4135 } 4136 4137 if (status & E1000_STATUS_FD) { 4138 *duplex = FULL_DUPLEX; 4139 DEBUGOUT("Full Duplex\r\n"); 4140 } else { 4141 *duplex = HALF_DUPLEX; 4142 DEBUGOUT(" Half Duplex\r\n"); 4143 } 4144 } else { 4145 DEBUGOUT("1000 Mbs, Full Duplex\r\n"); 4146 *speed = SPEED_1000; 4147 *duplex = FULL_DUPLEX; 4148 } 4149 4150 /* IGP01 PHY may advertise full duplex operation after speed downgrade 4151 * even if it is operating at half duplex. Here we set the duplex 4152 * settings to match the duplex in the link partner's capabilities. 4153 */ 4154 if (hw->phy_type == e1000_phy_igp && hw->speed_downgraded) { 4155 ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_EXP, &phy_data); 4156 if (ret_val) 4157 return ret_val; 4158 4159 if (!(phy_data & NWAY_ER_LP_NWAY_CAPS)) 4160 *duplex = HALF_DUPLEX; 4161 else { 4162 ret_val = e1000_read_phy_reg(hw, 4163 PHY_LP_ABILITY, &phy_data); 4164 if (ret_val) 4165 return ret_val; 4166 if ((*speed == SPEED_100 && 4167 !(phy_data & NWAY_LPAR_100TX_FD_CAPS)) 4168 || (*speed == SPEED_10 4169 && !(phy_data & NWAY_LPAR_10T_FD_CAPS))) 4170 *duplex = HALF_DUPLEX; 4171 } 4172 } 4173 4174 if ((hw->mac_type == e1000_80003es2lan) && 4175 (hw->media_type == e1000_media_type_copper)) { 4176 if (*speed == SPEED_1000) 4177 ret_val = e1000_configure_kmrn_for_1000(hw); 4178 else 4179 ret_val = e1000_configure_kmrn_for_10_100(hw, *duplex); 4180 if (ret_val) 4181 return ret_val; 4182 } 4183 return E1000_SUCCESS; 4184 } 4185 4186 /****************************************************************************** 4187 * Blocks until autoneg completes or times out (~4.5 seconds) 4188 * 4189 * hw - Struct containing variables accessed by shared code 4190 ******************************************************************************/ 4191 static int 4192 e1000_wait_autoneg(struct e1000_hw *hw) 4193 { 4194 uint16_t i; 4195 uint16_t phy_data; 4196 4197 DEBUGFUNC(); 4198 DEBUGOUT("Waiting for Auto-Neg to complete.\n"); 4199 4200 /* We will wait for autoneg to complete or timeout to expire. */ 4201 for (i = PHY_AUTO_NEG_TIME; i > 0; i--) { 4202 /* Read the MII Status Register and wait for Auto-Neg 4203 * Complete bit to be set. 4204 */ 4205 if (e1000_read_phy_reg(hw, PHY_STATUS, &phy_data) < 0) { 4206 DEBUGOUT("PHY Read Error\n"); 4207 return -E1000_ERR_PHY; 4208 } 4209 if (e1000_read_phy_reg(hw, PHY_STATUS, &phy_data) < 0) { 4210 DEBUGOUT("PHY Read Error\n"); 4211 return -E1000_ERR_PHY; 4212 } 4213 if (phy_data & MII_SR_AUTONEG_COMPLETE) { 4214 DEBUGOUT("Auto-Neg complete.\n"); 4215 return 0; 4216 } 4217 mdelay(100); 4218 } 4219 DEBUGOUT("Auto-Neg timedout.\n"); 4220 return -E1000_ERR_TIMEOUT; 4221 } 4222 4223 /****************************************************************************** 4224 * Raises the Management Data Clock 4225 * 4226 * hw - Struct containing variables accessed by shared code 4227 * ctrl - Device control register's current value 4228 ******************************************************************************/ 4229 static void 4230 e1000_raise_mdi_clk(struct e1000_hw *hw, uint32_t * ctrl) 4231 { 4232 /* Raise the clock input to the Management Data Clock (by setting the MDC 4233 * bit), and then delay 2 microseconds. 4234 */ 4235 E1000_WRITE_REG(hw, CTRL, (*ctrl | E1000_CTRL_MDC)); 4236 E1000_WRITE_FLUSH(hw); 4237 udelay(2); 4238 } 4239 4240 /****************************************************************************** 4241 * Lowers the Management Data Clock 4242 * 4243 * hw - Struct containing variables accessed by shared code 4244 * ctrl - Device control register's current value 4245 ******************************************************************************/ 4246 static void 4247 e1000_lower_mdi_clk(struct e1000_hw *hw, uint32_t * ctrl) 4248 { 4249 /* Lower the clock input to the Management Data Clock (by clearing the MDC 4250 * bit), and then delay 2 microseconds. 4251 */ 4252 E1000_WRITE_REG(hw, CTRL, (*ctrl & ~E1000_CTRL_MDC)); 4253 E1000_WRITE_FLUSH(hw); 4254 udelay(2); 4255 } 4256 4257 /****************************************************************************** 4258 * Shifts data bits out to the PHY 4259 * 4260 * hw - Struct containing variables accessed by shared code 4261 * data - Data to send out to the PHY 4262 * count - Number of bits to shift out 4263 * 4264 * Bits are shifted out in MSB to LSB order. 4265 ******************************************************************************/ 4266 static void 4267 e1000_shift_out_mdi_bits(struct e1000_hw *hw, uint32_t data, uint16_t count) 4268 { 4269 uint32_t ctrl; 4270 uint32_t mask; 4271 4272 /* We need to shift "count" number of bits out to the PHY. So, the value 4273 * in the "data" parameter will be shifted out to the PHY one bit at a 4274 * time. In order to do this, "data" must be broken down into bits. 4275 */ 4276 mask = 0x01; 4277 mask <<= (count - 1); 4278 4279 ctrl = E1000_READ_REG(hw, CTRL); 4280 4281 /* Set MDIO_DIR and MDC_DIR direction bits to be used as output pins. */ 4282 ctrl |= (E1000_CTRL_MDIO_DIR | E1000_CTRL_MDC_DIR); 4283 4284 while (mask) { 4285 /* A "1" is shifted out to the PHY by setting the MDIO bit to "1" and 4286 * then raising and lowering the Management Data Clock. A "0" is 4287 * shifted out to the PHY by setting the MDIO bit to "0" and then 4288 * raising and lowering the clock. 4289 */ 4290 if (data & mask) 4291 ctrl |= E1000_CTRL_MDIO; 4292 else 4293 ctrl &= ~E1000_CTRL_MDIO; 4294 4295 E1000_WRITE_REG(hw, CTRL, ctrl); 4296 E1000_WRITE_FLUSH(hw); 4297 4298 udelay(2); 4299 4300 e1000_raise_mdi_clk(hw, &ctrl); 4301 e1000_lower_mdi_clk(hw, &ctrl); 4302 4303 mask = mask >> 1; 4304 } 4305 } 4306 4307 /****************************************************************************** 4308 * Shifts data bits in from the PHY 4309 * 4310 * hw - Struct containing variables accessed by shared code 4311 * 4312 * Bits are shifted in in MSB to LSB order. 4313 ******************************************************************************/ 4314 static uint16_t 4315 e1000_shift_in_mdi_bits(struct e1000_hw *hw) 4316 { 4317 uint32_t ctrl; 4318 uint16_t data = 0; 4319 uint8_t i; 4320 4321 /* In order to read a register from the PHY, we need to shift in a total 4322 * of 18 bits from the PHY. The first two bit (turnaround) times are used 4323 * to avoid contention on the MDIO pin when a read operation is performed. 4324 * These two bits are ignored by us and thrown away. Bits are "shifted in" 4325 * by raising the input to the Management Data Clock (setting the MDC bit), 4326 * and then reading the value of the MDIO bit. 4327 */ 4328 ctrl = E1000_READ_REG(hw, CTRL); 4329 4330 /* Clear MDIO_DIR (SWDPIO1) to indicate this bit is to be used as input. */ 4331 ctrl &= ~E1000_CTRL_MDIO_DIR; 4332 ctrl &= ~E1000_CTRL_MDIO; 4333 4334 E1000_WRITE_REG(hw, CTRL, ctrl); 4335 E1000_WRITE_FLUSH(hw); 4336 4337 /* Raise and Lower the clock before reading in the data. This accounts for 4338 * the turnaround bits. The first clock occurred when we clocked out the 4339 * last bit of the Register Address. 4340 */ 4341 e1000_raise_mdi_clk(hw, &ctrl); 4342 e1000_lower_mdi_clk(hw, &ctrl); 4343 4344 for (data = 0, i = 0; i < 16; i++) { 4345 data = data << 1; 4346 e1000_raise_mdi_clk(hw, &ctrl); 4347 ctrl = E1000_READ_REG(hw, CTRL); 4348 /* Check to see if we shifted in a "1". */ 4349 if (ctrl & E1000_CTRL_MDIO) 4350 data |= 1; 4351 e1000_lower_mdi_clk(hw, &ctrl); 4352 } 4353 4354 e1000_raise_mdi_clk(hw, &ctrl); 4355 e1000_lower_mdi_clk(hw, &ctrl); 4356 4357 return data; 4358 } 4359 4360 /***************************************************************************** 4361 * Reads the value from a PHY register 4362 * 4363 * hw - Struct containing variables accessed by shared code 4364 * reg_addr - address of the PHY register to read 4365 ******************************************************************************/ 4366 static int 4367 e1000_read_phy_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t * phy_data) 4368 { 4369 uint32_t i; 4370 uint32_t mdic = 0; 4371 const uint32_t phy_addr = 1; 4372 4373 if (reg_addr > MAX_PHY_REG_ADDRESS) { 4374 DEBUGOUT("PHY Address %d is out of range\n", reg_addr); 4375 return -E1000_ERR_PARAM; 4376 } 4377 4378 if (hw->mac_type > e1000_82543) { 4379 /* Set up Op-code, Phy Address, and register address in the MDI 4380 * Control register. The MAC will take care of interfacing with the 4381 * PHY to retrieve the desired data. 4382 */ 4383 mdic = ((reg_addr << E1000_MDIC_REG_SHIFT) | 4384 (phy_addr << E1000_MDIC_PHY_SHIFT) | 4385 (E1000_MDIC_OP_READ)); 4386 4387 E1000_WRITE_REG(hw, MDIC, mdic); 4388 4389 /* Poll the ready bit to see if the MDI read completed */ 4390 for (i = 0; i < 64; i++) { 4391 udelay(10); 4392 mdic = E1000_READ_REG(hw, MDIC); 4393 if (mdic & E1000_MDIC_READY) 4394 break; 4395 } 4396 if (!(mdic & E1000_MDIC_READY)) { 4397 DEBUGOUT("MDI Read did not complete\n"); 4398 return -E1000_ERR_PHY; 4399 } 4400 if (mdic & E1000_MDIC_ERROR) { 4401 DEBUGOUT("MDI Error\n"); 4402 return -E1000_ERR_PHY; 4403 } 4404 *phy_data = (uint16_t) mdic; 4405 } else { 4406 /* We must first send a preamble through the MDIO pin to signal the 4407 * beginning of an MII instruction. This is done by sending 32 4408 * consecutive "1" bits. 4409 */ 4410 e1000_shift_out_mdi_bits(hw, PHY_PREAMBLE, PHY_PREAMBLE_SIZE); 4411 4412 /* Now combine the next few fields that are required for a read 4413 * operation. We use this method instead of calling the 4414 * e1000_shift_out_mdi_bits routine five different times. The format of 4415 * a MII read instruction consists of a shift out of 14 bits and is 4416 * defined as follows: 4417 * <Preamble><SOF><Op Code><Phy Addr><Reg Addr> 4418 * followed by a shift in of 18 bits. This first two bits shifted in 4419 * are TurnAround bits used to avoid contention on the MDIO pin when a 4420 * READ operation is performed. These two bits are thrown away 4421 * followed by a shift in of 16 bits which contains the desired data. 4422 */ 4423 mdic = ((reg_addr) | (phy_addr << 5) | 4424 (PHY_OP_READ << 10) | (PHY_SOF << 12)); 4425 4426 e1000_shift_out_mdi_bits(hw, mdic, 14); 4427 4428 /* Now that we've shifted out the read command to the MII, we need to 4429 * "shift in" the 16-bit value (18 total bits) of the requested PHY 4430 * register address. 4431 */ 4432 *phy_data = e1000_shift_in_mdi_bits(hw); 4433 } 4434 return 0; 4435 } 4436 4437 /****************************************************************************** 4438 * Writes a value to a PHY register 4439 * 4440 * hw - Struct containing variables accessed by shared code 4441 * reg_addr - address of the PHY register to write 4442 * data - data to write to the PHY 4443 ******************************************************************************/ 4444 static int 4445 e1000_write_phy_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t phy_data) 4446 { 4447 uint32_t i; 4448 uint32_t mdic = 0; 4449 const uint32_t phy_addr = 1; 4450 4451 if (reg_addr > MAX_PHY_REG_ADDRESS) { 4452 DEBUGOUT("PHY Address %d is out of range\n", reg_addr); 4453 return -E1000_ERR_PARAM; 4454 } 4455 4456 if (hw->mac_type > e1000_82543) { 4457 /* Set up Op-code, Phy Address, register address, and data intended 4458 * for the PHY register in the MDI Control register. The MAC will take 4459 * care of interfacing with the PHY to send the desired data. 4460 */ 4461 mdic = (((uint32_t) phy_data) | 4462 (reg_addr << E1000_MDIC_REG_SHIFT) | 4463 (phy_addr << E1000_MDIC_PHY_SHIFT) | 4464 (E1000_MDIC_OP_WRITE)); 4465 4466 E1000_WRITE_REG(hw, MDIC, mdic); 4467 4468 /* Poll the ready bit to see if the MDI read completed */ 4469 for (i = 0; i < 64; i++) { 4470 udelay(10); 4471 mdic = E1000_READ_REG(hw, MDIC); 4472 if (mdic & E1000_MDIC_READY) 4473 break; 4474 } 4475 if (!(mdic & E1000_MDIC_READY)) { 4476 DEBUGOUT("MDI Write did not complete\n"); 4477 return -E1000_ERR_PHY; 4478 } 4479 } else { 4480 /* We'll need to use the SW defined pins to shift the write command 4481 * out to the PHY. We first send a preamble to the PHY to signal the 4482 * beginning of the MII instruction. This is done by sending 32 4483 * consecutive "1" bits. 4484 */ 4485 e1000_shift_out_mdi_bits(hw, PHY_PREAMBLE, PHY_PREAMBLE_SIZE); 4486 4487 /* Now combine the remaining required fields that will indicate a 4488 * write operation. We use this method instead of calling the 4489 * e1000_shift_out_mdi_bits routine for each field in the command. The 4490 * format of a MII write instruction is as follows: 4491 * <Preamble><SOF><Op Code><Phy Addr><Reg Addr><Turnaround><Data>. 4492 */ 4493 mdic = ((PHY_TURNAROUND) | (reg_addr << 2) | (phy_addr << 7) | 4494 (PHY_OP_WRITE << 12) | (PHY_SOF << 14)); 4495 mdic <<= 16; 4496 mdic |= (uint32_t) phy_data; 4497 4498 e1000_shift_out_mdi_bits(hw, mdic, 32); 4499 } 4500 return 0; 4501 } 4502 4503 /****************************************************************************** 4504 * Checks if PHY reset is blocked due to SOL/IDER session, for example. 4505 * Returning E1000_BLK_PHY_RESET isn't necessarily an error. But it's up to 4506 * the caller to figure out how to deal with it. 4507 * 4508 * hw - Struct containing variables accessed by shared code 4509 * 4510 * returns: - E1000_BLK_PHY_RESET 4511 * E1000_SUCCESS 4512 * 4513 *****************************************************************************/ 4514 int32_t 4515 e1000_check_phy_reset_block(struct e1000_hw *hw) 4516 { 4517 uint32_t manc = 0; 4518 uint32_t fwsm = 0; 4519 4520 if (hw->mac_type == e1000_ich8lan) { 4521 fwsm = E1000_READ_REG(hw, FWSM); 4522 return (fwsm & E1000_FWSM_RSPCIPHY) ? E1000_SUCCESS 4523 : E1000_BLK_PHY_RESET; 4524 } 4525 4526 if (hw->mac_type > e1000_82547_rev_2) 4527 manc = E1000_READ_REG(hw, MANC); 4528 return (manc & E1000_MANC_BLK_PHY_RST_ON_IDE) ? 4529 E1000_BLK_PHY_RESET : E1000_SUCCESS; 4530 } 4531 4532 /*************************************************************************** 4533 * Checks if the PHY configuration is done 4534 * 4535 * hw: Struct containing variables accessed by shared code 4536 * 4537 * returns: - E1000_ERR_RESET if fail to reset MAC 4538 * E1000_SUCCESS at any other case. 4539 * 4540 ***************************************************************************/ 4541 static int32_t 4542 e1000_get_phy_cfg_done(struct e1000_hw *hw) 4543 { 4544 int32_t timeout = PHY_CFG_TIMEOUT; 4545 uint32_t cfg_mask = E1000_EEPROM_CFG_DONE; 4546 4547 DEBUGFUNC(); 4548 4549 switch (hw->mac_type) { 4550 default: 4551 mdelay(10); 4552 break; 4553 4554 case e1000_80003es2lan: 4555 /* Separate *_CFG_DONE_* bit for each port */ 4556 if (e1000_is_second_port(hw)) 4557 cfg_mask = E1000_EEPROM_CFG_DONE_PORT_1; 4558 /* Fall Through */ 4559 4560 case e1000_82571: 4561 case e1000_82572: 4562 case e1000_igb: 4563 while (timeout) { 4564 if (hw->mac_type == e1000_igb) { 4565 if (E1000_READ_REG(hw, I210_EEMNGCTL) & cfg_mask) 4566 break; 4567 } else { 4568 if (E1000_READ_REG(hw, EEMNGCTL) & cfg_mask) 4569 break; 4570 } 4571 mdelay(1); 4572 timeout--; 4573 } 4574 if (!timeout) { 4575 DEBUGOUT("MNG configuration cycle has not " 4576 "completed.\n"); 4577 return -E1000_ERR_RESET; 4578 } 4579 break; 4580 } 4581 4582 return E1000_SUCCESS; 4583 } 4584 4585 /****************************************************************************** 4586 * Returns the PHY to the power-on reset state 4587 * 4588 * hw - Struct containing variables accessed by shared code 4589 ******************************************************************************/ 4590 int32_t 4591 e1000_phy_hw_reset(struct e1000_hw *hw) 4592 { 4593 uint16_t swfw = E1000_SWFW_PHY0_SM; 4594 uint32_t ctrl, ctrl_ext; 4595 uint32_t led_ctrl; 4596 int32_t ret_val; 4597 4598 DEBUGFUNC(); 4599 4600 /* In the case of the phy reset being blocked, it's not an error, we 4601 * simply return success without performing the reset. */ 4602 ret_val = e1000_check_phy_reset_block(hw); 4603 if (ret_val) 4604 return E1000_SUCCESS; 4605 4606 DEBUGOUT("Resetting Phy...\n"); 4607 4608 if (hw->mac_type > e1000_82543) { 4609 if (e1000_is_second_port(hw)) 4610 swfw = E1000_SWFW_PHY1_SM; 4611 4612 if (e1000_swfw_sync_acquire(hw, swfw)) { 4613 DEBUGOUT("Unable to acquire swfw sync\n"); 4614 return -E1000_ERR_SWFW_SYNC; 4615 } 4616 4617 /* Read the device control register and assert the E1000_CTRL_PHY_RST 4618 * bit. Then, take it out of reset. 4619 */ 4620 ctrl = E1000_READ_REG(hw, CTRL); 4621 E1000_WRITE_REG(hw, CTRL, ctrl | E1000_CTRL_PHY_RST); 4622 E1000_WRITE_FLUSH(hw); 4623 4624 if (hw->mac_type < e1000_82571) 4625 udelay(10); 4626 else 4627 udelay(100); 4628 4629 E1000_WRITE_REG(hw, CTRL, ctrl); 4630 E1000_WRITE_FLUSH(hw); 4631 4632 if (hw->mac_type >= e1000_82571) 4633 mdelay(10); 4634 4635 } else { 4636 /* Read the Extended Device Control Register, assert the PHY_RESET_DIR 4637 * bit to put the PHY into reset. Then, take it out of reset. 4638 */ 4639 ctrl_ext = E1000_READ_REG(hw, CTRL_EXT); 4640 ctrl_ext |= E1000_CTRL_EXT_SDP4_DIR; 4641 ctrl_ext &= ~E1000_CTRL_EXT_SDP4_DATA; 4642 E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext); 4643 E1000_WRITE_FLUSH(hw); 4644 mdelay(10); 4645 ctrl_ext |= E1000_CTRL_EXT_SDP4_DATA; 4646 E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext); 4647 E1000_WRITE_FLUSH(hw); 4648 } 4649 udelay(150); 4650 4651 if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) { 4652 /* Configure activity LED after PHY reset */ 4653 led_ctrl = E1000_READ_REG(hw, LEDCTL); 4654 led_ctrl &= IGP_ACTIVITY_LED_MASK; 4655 led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE); 4656 E1000_WRITE_REG(hw, LEDCTL, led_ctrl); 4657 } 4658 4659 e1000_swfw_sync_release(hw, swfw); 4660 4661 /* Wait for FW to finish PHY configuration. */ 4662 ret_val = e1000_get_phy_cfg_done(hw); 4663 if (ret_val != E1000_SUCCESS) 4664 return ret_val; 4665 4666 return ret_val; 4667 } 4668 4669 /****************************************************************************** 4670 * IGP phy init script - initializes the GbE PHY 4671 * 4672 * hw - Struct containing variables accessed by shared code 4673 *****************************************************************************/ 4674 static void 4675 e1000_phy_init_script(struct e1000_hw *hw) 4676 { 4677 uint32_t ret_val; 4678 uint16_t phy_saved_data; 4679 DEBUGFUNC(); 4680 4681 if (hw->phy_init_script) { 4682 mdelay(20); 4683 4684 /* Save off the current value of register 0x2F5B to be 4685 * restored at the end of this routine. */ 4686 ret_val = e1000_read_phy_reg(hw, 0x2F5B, &phy_saved_data); 4687 4688 /* Disabled the PHY transmitter */ 4689 e1000_write_phy_reg(hw, 0x2F5B, 0x0003); 4690 4691 mdelay(20); 4692 4693 e1000_write_phy_reg(hw, 0x0000, 0x0140); 4694 4695 mdelay(5); 4696 4697 switch (hw->mac_type) { 4698 case e1000_82541: 4699 case e1000_82547: 4700 e1000_write_phy_reg(hw, 0x1F95, 0x0001); 4701 4702 e1000_write_phy_reg(hw, 0x1F71, 0xBD21); 4703 4704 e1000_write_phy_reg(hw, 0x1F79, 0x0018); 4705 4706 e1000_write_phy_reg(hw, 0x1F30, 0x1600); 4707 4708 e1000_write_phy_reg(hw, 0x1F31, 0x0014); 4709 4710 e1000_write_phy_reg(hw, 0x1F32, 0x161C); 4711 4712 e1000_write_phy_reg(hw, 0x1F94, 0x0003); 4713 4714 e1000_write_phy_reg(hw, 0x1F96, 0x003F); 4715 4716 e1000_write_phy_reg(hw, 0x2010, 0x0008); 4717 break; 4718 4719 case e1000_82541_rev_2: 4720 case e1000_82547_rev_2: 4721 e1000_write_phy_reg(hw, 0x1F73, 0x0099); 4722 break; 4723 default: 4724 break; 4725 } 4726 4727 e1000_write_phy_reg(hw, 0x0000, 0x3300); 4728 4729 mdelay(20); 4730 4731 /* Now enable the transmitter */ 4732 if (!ret_val) 4733 e1000_write_phy_reg(hw, 0x2F5B, phy_saved_data); 4734 4735 if (hw->mac_type == e1000_82547) { 4736 uint16_t fused, fine, coarse; 4737 4738 /* Move to analog registers page */ 4739 e1000_read_phy_reg(hw, 4740 IGP01E1000_ANALOG_SPARE_FUSE_STATUS, &fused); 4741 4742 if (!(fused & IGP01E1000_ANALOG_SPARE_FUSE_ENABLED)) { 4743 e1000_read_phy_reg(hw, 4744 IGP01E1000_ANALOG_FUSE_STATUS, &fused); 4745 4746 fine = fused & IGP01E1000_ANALOG_FUSE_FINE_MASK; 4747 coarse = fused 4748 & IGP01E1000_ANALOG_FUSE_COARSE_MASK; 4749 4750 if (coarse > 4751 IGP01E1000_ANALOG_FUSE_COARSE_THRESH) { 4752 coarse -= 4753 IGP01E1000_ANALOG_FUSE_COARSE_10; 4754 fine -= IGP01E1000_ANALOG_FUSE_FINE_1; 4755 } else if (coarse 4756 == IGP01E1000_ANALOG_FUSE_COARSE_THRESH) 4757 fine -= IGP01E1000_ANALOG_FUSE_FINE_10; 4758 4759 fused = (fused 4760 & IGP01E1000_ANALOG_FUSE_POLY_MASK) | 4761 (fine 4762 & IGP01E1000_ANALOG_FUSE_FINE_MASK) | 4763 (coarse 4764 & IGP01E1000_ANALOG_FUSE_COARSE_MASK); 4765 4766 e1000_write_phy_reg(hw, 4767 IGP01E1000_ANALOG_FUSE_CONTROL, fused); 4768 e1000_write_phy_reg(hw, 4769 IGP01E1000_ANALOG_FUSE_BYPASS, 4770 IGP01E1000_ANALOG_FUSE_ENABLE_SW_CONTROL); 4771 } 4772 } 4773 } 4774 } 4775 4776 /****************************************************************************** 4777 * Resets the PHY 4778 * 4779 * hw - Struct containing variables accessed by shared code 4780 * 4781 * Sets bit 15 of the MII Control register 4782 ******************************************************************************/ 4783 int32_t 4784 e1000_phy_reset(struct e1000_hw *hw) 4785 { 4786 int32_t ret_val; 4787 uint16_t phy_data; 4788 4789 DEBUGFUNC(); 4790 4791 /* In the case of the phy reset being blocked, it's not an error, we 4792 * simply return success without performing the reset. */ 4793 ret_val = e1000_check_phy_reset_block(hw); 4794 if (ret_val) 4795 return E1000_SUCCESS; 4796 4797 switch (hw->phy_type) { 4798 case e1000_phy_igp: 4799 case e1000_phy_igp_2: 4800 case e1000_phy_igp_3: 4801 case e1000_phy_ife: 4802 case e1000_phy_igb: 4803 ret_val = e1000_phy_hw_reset(hw); 4804 if (ret_val) 4805 return ret_val; 4806 break; 4807 default: 4808 ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data); 4809 if (ret_val) 4810 return ret_val; 4811 4812 phy_data |= MII_CR_RESET; 4813 ret_val = e1000_write_phy_reg(hw, PHY_CTRL, phy_data); 4814 if (ret_val) 4815 return ret_val; 4816 4817 udelay(1); 4818 break; 4819 } 4820 4821 if (hw->phy_type == e1000_phy_igp || hw->phy_type == e1000_phy_igp_2) 4822 e1000_phy_init_script(hw); 4823 4824 return E1000_SUCCESS; 4825 } 4826 4827 static int e1000_set_phy_type (struct e1000_hw *hw) 4828 { 4829 DEBUGFUNC (); 4830 4831 if (hw->mac_type == e1000_undefined) 4832 return -E1000_ERR_PHY_TYPE; 4833 4834 switch (hw->phy_id) { 4835 case M88E1000_E_PHY_ID: 4836 case M88E1000_I_PHY_ID: 4837 case M88E1011_I_PHY_ID: 4838 case M88E1111_I_PHY_ID: 4839 hw->phy_type = e1000_phy_m88; 4840 break; 4841 case IGP01E1000_I_PHY_ID: 4842 if (hw->mac_type == e1000_82541 || 4843 hw->mac_type == e1000_82541_rev_2 || 4844 hw->mac_type == e1000_82547 || 4845 hw->mac_type == e1000_82547_rev_2) { 4846 hw->phy_type = e1000_phy_igp; 4847 break; 4848 } 4849 case IGP03E1000_E_PHY_ID: 4850 hw->phy_type = e1000_phy_igp_3; 4851 break; 4852 case IFE_E_PHY_ID: 4853 case IFE_PLUS_E_PHY_ID: 4854 case IFE_C_E_PHY_ID: 4855 hw->phy_type = e1000_phy_ife; 4856 break; 4857 case GG82563_E_PHY_ID: 4858 if (hw->mac_type == e1000_80003es2lan) { 4859 hw->phy_type = e1000_phy_gg82563; 4860 break; 4861 } 4862 case BME1000_E_PHY_ID: 4863 hw->phy_type = e1000_phy_bm; 4864 break; 4865 case I210_I_PHY_ID: 4866 hw->phy_type = e1000_phy_igb; 4867 break; 4868 /* Fall Through */ 4869 default: 4870 /* Should never have loaded on this device */ 4871 hw->phy_type = e1000_phy_undefined; 4872 return -E1000_ERR_PHY_TYPE; 4873 } 4874 4875 return E1000_SUCCESS; 4876 } 4877 4878 /****************************************************************************** 4879 * Probes the expected PHY address for known PHY IDs 4880 * 4881 * hw - Struct containing variables accessed by shared code 4882 ******************************************************************************/ 4883 static int32_t 4884 e1000_detect_gig_phy(struct e1000_hw *hw) 4885 { 4886 int32_t phy_init_status, ret_val; 4887 uint16_t phy_id_high, phy_id_low; 4888 bool match = false; 4889 4890 DEBUGFUNC(); 4891 4892 /* The 82571 firmware may still be configuring the PHY. In this 4893 * case, we cannot access the PHY until the configuration is done. So 4894 * we explicitly set the PHY values. */ 4895 if (hw->mac_type == e1000_82571 || 4896 hw->mac_type == e1000_82572) { 4897 hw->phy_id = IGP01E1000_I_PHY_ID; 4898 hw->phy_type = e1000_phy_igp_2; 4899 return E1000_SUCCESS; 4900 } 4901 4902 /* ESB-2 PHY reads require e1000_phy_gg82563 to be set because of a 4903 * work- around that forces PHY page 0 to be set or the reads fail. 4904 * The rest of the code in this routine uses e1000_read_phy_reg to 4905 * read the PHY ID. So for ESB-2 we need to have this set so our 4906 * reads won't fail. If the attached PHY is not a e1000_phy_gg82563, 4907 * the routines below will figure this out as well. */ 4908 if (hw->mac_type == e1000_80003es2lan) 4909 hw->phy_type = e1000_phy_gg82563; 4910 4911 /* Read the PHY ID Registers to identify which PHY is onboard. */ 4912 ret_val = e1000_read_phy_reg(hw, PHY_ID1, &phy_id_high); 4913 if (ret_val) 4914 return ret_val; 4915 4916 hw->phy_id = (uint32_t) (phy_id_high << 16); 4917 udelay(20); 4918 ret_val = e1000_read_phy_reg(hw, PHY_ID2, &phy_id_low); 4919 if (ret_val) 4920 return ret_val; 4921 4922 hw->phy_id |= (uint32_t) (phy_id_low & PHY_REVISION_MASK); 4923 hw->phy_revision = (uint32_t) phy_id_low & ~PHY_REVISION_MASK; 4924 4925 switch (hw->mac_type) { 4926 case e1000_82543: 4927 if (hw->phy_id == M88E1000_E_PHY_ID) 4928 match = true; 4929 break; 4930 case e1000_82544: 4931 if (hw->phy_id == M88E1000_I_PHY_ID) 4932 match = true; 4933 break; 4934 case e1000_82540: 4935 case e1000_82545: 4936 case e1000_82545_rev_3: 4937 case e1000_82546: 4938 case e1000_82546_rev_3: 4939 if (hw->phy_id == M88E1011_I_PHY_ID) 4940 match = true; 4941 break; 4942 case e1000_82541: 4943 case e1000_82541_rev_2: 4944 case e1000_82547: 4945 case e1000_82547_rev_2: 4946 if(hw->phy_id == IGP01E1000_I_PHY_ID) 4947 match = true; 4948 4949 break; 4950 case e1000_82573: 4951 if (hw->phy_id == M88E1111_I_PHY_ID) 4952 match = true; 4953 break; 4954 case e1000_82574: 4955 if (hw->phy_id == BME1000_E_PHY_ID) 4956 match = true; 4957 break; 4958 case e1000_80003es2lan: 4959 if (hw->phy_id == GG82563_E_PHY_ID) 4960 match = true; 4961 break; 4962 case e1000_ich8lan: 4963 if (hw->phy_id == IGP03E1000_E_PHY_ID) 4964 match = true; 4965 if (hw->phy_id == IFE_E_PHY_ID) 4966 match = true; 4967 if (hw->phy_id == IFE_PLUS_E_PHY_ID) 4968 match = true; 4969 if (hw->phy_id == IFE_C_E_PHY_ID) 4970 match = true; 4971 break; 4972 case e1000_igb: 4973 if (hw->phy_id == I210_I_PHY_ID) 4974 match = true; 4975 break; 4976 default: 4977 DEBUGOUT("Invalid MAC type %d\n", hw->mac_type); 4978 return -E1000_ERR_CONFIG; 4979 } 4980 4981 phy_init_status = e1000_set_phy_type(hw); 4982 4983 if ((match) && (phy_init_status == E1000_SUCCESS)) { 4984 DEBUGOUT("PHY ID 0x%X detected\n", hw->phy_id); 4985 return 0; 4986 } 4987 DEBUGOUT("Invalid PHY ID 0x%X\n", hw->phy_id); 4988 return -E1000_ERR_PHY; 4989 } 4990 4991 /***************************************************************************** 4992 * Set media type and TBI compatibility. 4993 * 4994 * hw - Struct containing variables accessed by shared code 4995 * **************************************************************************/ 4996 void 4997 e1000_set_media_type(struct e1000_hw *hw) 4998 { 4999 uint32_t status; 5000 5001 DEBUGFUNC(); 5002 5003 if (hw->mac_type != e1000_82543) { 5004 /* tbi_compatibility is only valid on 82543 */ 5005 hw->tbi_compatibility_en = false; 5006 } 5007 5008 switch (hw->device_id) { 5009 case E1000_DEV_ID_82545GM_SERDES: 5010 case E1000_DEV_ID_82546GB_SERDES: 5011 case E1000_DEV_ID_82571EB_SERDES: 5012 case E1000_DEV_ID_82571EB_SERDES_DUAL: 5013 case E1000_DEV_ID_82571EB_SERDES_QUAD: 5014 case E1000_DEV_ID_82572EI_SERDES: 5015 case E1000_DEV_ID_80003ES2LAN_SERDES_DPT: 5016 hw->media_type = e1000_media_type_internal_serdes; 5017 break; 5018 default: 5019 switch (hw->mac_type) { 5020 case e1000_82542_rev2_0: 5021 case e1000_82542_rev2_1: 5022 hw->media_type = e1000_media_type_fiber; 5023 break; 5024 case e1000_ich8lan: 5025 case e1000_82573: 5026 case e1000_82574: 5027 case e1000_igb: 5028 /* The STATUS_TBIMODE bit is reserved or reused 5029 * for the this device. 5030 */ 5031 hw->media_type = e1000_media_type_copper; 5032 break; 5033 default: 5034 status = E1000_READ_REG(hw, STATUS); 5035 if (status & E1000_STATUS_TBIMODE) { 5036 hw->media_type = e1000_media_type_fiber; 5037 /* tbi_compatibility not valid on fiber */ 5038 hw->tbi_compatibility_en = false; 5039 } else { 5040 hw->media_type = e1000_media_type_copper; 5041 } 5042 break; 5043 } 5044 } 5045 } 5046 5047 /** 5048 * e1000_sw_init - Initialize general software structures (struct e1000_adapter) 5049 * 5050 * e1000_sw_init initializes the Adapter private data structure. 5051 * Fields are initialized based on PCI device information and 5052 * OS network device settings (MTU size). 5053 **/ 5054 5055 static int 5056 e1000_sw_init(struct e1000_hw *hw) 5057 { 5058 int result; 5059 5060 /* PCI config space info */ 5061 #ifdef CONFIG_DM_ETH 5062 dm_pci_read_config16(hw->pdev, PCI_VENDOR_ID, &hw->vendor_id); 5063 dm_pci_read_config16(hw->pdev, PCI_DEVICE_ID, &hw->device_id); 5064 dm_pci_read_config16(hw->pdev, PCI_SUBSYSTEM_VENDOR_ID, 5065 &hw->subsystem_vendor_id); 5066 dm_pci_read_config16(hw->pdev, PCI_SUBSYSTEM_ID, &hw->subsystem_id); 5067 5068 dm_pci_read_config8(hw->pdev, PCI_REVISION_ID, &hw->revision_id); 5069 dm_pci_read_config16(hw->pdev, PCI_COMMAND, &hw->pci_cmd_word); 5070 #else 5071 pci_read_config_word(hw->pdev, PCI_VENDOR_ID, &hw->vendor_id); 5072 pci_read_config_word(hw->pdev, PCI_DEVICE_ID, &hw->device_id); 5073 pci_read_config_word(hw->pdev, PCI_SUBSYSTEM_VENDOR_ID, 5074 &hw->subsystem_vendor_id); 5075 pci_read_config_word(hw->pdev, PCI_SUBSYSTEM_ID, &hw->subsystem_id); 5076 5077 pci_read_config_byte(hw->pdev, PCI_REVISION_ID, &hw->revision_id); 5078 pci_read_config_word(hw->pdev, PCI_COMMAND, &hw->pci_cmd_word); 5079 #endif 5080 5081 /* identify the MAC */ 5082 result = e1000_set_mac_type(hw); 5083 if (result) { 5084 E1000_ERR(hw, "Unknown MAC Type\n"); 5085 return result; 5086 } 5087 5088 switch (hw->mac_type) { 5089 default: 5090 break; 5091 case e1000_82541: 5092 case e1000_82547: 5093 case e1000_82541_rev_2: 5094 case e1000_82547_rev_2: 5095 hw->phy_init_script = 1; 5096 break; 5097 } 5098 5099 /* flow control settings */ 5100 hw->fc_high_water = E1000_FC_HIGH_THRESH; 5101 hw->fc_low_water = E1000_FC_LOW_THRESH; 5102 hw->fc_pause_time = E1000_FC_PAUSE_TIME; 5103 hw->fc_send_xon = 1; 5104 5105 /* Media type - copper or fiber */ 5106 hw->tbi_compatibility_en = true; 5107 e1000_set_media_type(hw); 5108 5109 if (hw->mac_type >= e1000_82543) { 5110 uint32_t status = E1000_READ_REG(hw, STATUS); 5111 5112 if (status & E1000_STATUS_TBIMODE) { 5113 DEBUGOUT("fiber interface\n"); 5114 hw->media_type = e1000_media_type_fiber; 5115 } else { 5116 DEBUGOUT("copper interface\n"); 5117 hw->media_type = e1000_media_type_copper; 5118 } 5119 } else { 5120 hw->media_type = e1000_media_type_fiber; 5121 } 5122 5123 hw->wait_autoneg_complete = true; 5124 if (hw->mac_type < e1000_82543) 5125 hw->report_tx_early = 0; 5126 else 5127 hw->report_tx_early = 1; 5128 5129 return E1000_SUCCESS; 5130 } 5131 5132 void 5133 fill_rx(struct e1000_hw *hw) 5134 { 5135 struct e1000_rx_desc *rd; 5136 unsigned long flush_start, flush_end; 5137 5138 rx_last = rx_tail; 5139 rd = rx_base + rx_tail; 5140 rx_tail = (rx_tail + 1) % 8; 5141 memset(rd, 0, 16); 5142 rd->buffer_addr = cpu_to_le64((unsigned long)packet); 5143 5144 /* 5145 * Make sure there are no stale data in WB over this area, which 5146 * might get written into the memory while the e1000 also writes 5147 * into the same memory area. 5148 */ 5149 invalidate_dcache_range((unsigned long)packet, 5150 (unsigned long)packet + 4096); 5151 /* Dump the DMA descriptor into RAM. */ 5152 flush_start = ((unsigned long)rd) & ~(ARCH_DMA_MINALIGN - 1); 5153 flush_end = flush_start + roundup(sizeof(*rd), ARCH_DMA_MINALIGN); 5154 flush_dcache_range(flush_start, flush_end); 5155 5156 E1000_WRITE_REG(hw, RDT, rx_tail); 5157 } 5158 5159 /** 5160 * e1000_configure_tx - Configure 8254x Transmit Unit after Reset 5161 * @adapter: board private structure 5162 * 5163 * Configure the Tx unit of the MAC after a reset. 5164 **/ 5165 5166 static void 5167 e1000_configure_tx(struct e1000_hw *hw) 5168 { 5169 unsigned long tctl; 5170 unsigned long tipg, tarc; 5171 uint32_t ipgr1, ipgr2; 5172 5173 E1000_WRITE_REG(hw, TDBAL, lower_32_bits((unsigned long)tx_base)); 5174 E1000_WRITE_REG(hw, TDBAH, upper_32_bits((unsigned long)tx_base)); 5175 5176 E1000_WRITE_REG(hw, TDLEN, 128); 5177 5178 /* Setup the HW Tx Head and Tail descriptor pointers */ 5179 E1000_WRITE_REG(hw, TDH, 0); 5180 E1000_WRITE_REG(hw, TDT, 0); 5181 tx_tail = 0; 5182 5183 /* Set the default values for the Tx Inter Packet Gap timer */ 5184 if (hw->mac_type <= e1000_82547_rev_2 && 5185 (hw->media_type == e1000_media_type_fiber || 5186 hw->media_type == e1000_media_type_internal_serdes)) 5187 tipg = DEFAULT_82543_TIPG_IPGT_FIBER; 5188 else 5189 tipg = DEFAULT_82543_TIPG_IPGT_COPPER; 5190 5191 /* Set the default values for the Tx Inter Packet Gap timer */ 5192 switch (hw->mac_type) { 5193 case e1000_82542_rev2_0: 5194 case e1000_82542_rev2_1: 5195 tipg = DEFAULT_82542_TIPG_IPGT; 5196 ipgr1 = DEFAULT_82542_TIPG_IPGR1; 5197 ipgr2 = DEFAULT_82542_TIPG_IPGR2; 5198 break; 5199 case e1000_80003es2lan: 5200 ipgr1 = DEFAULT_82543_TIPG_IPGR1; 5201 ipgr2 = DEFAULT_80003ES2LAN_TIPG_IPGR2; 5202 break; 5203 default: 5204 ipgr1 = DEFAULT_82543_TIPG_IPGR1; 5205 ipgr2 = DEFAULT_82543_TIPG_IPGR2; 5206 break; 5207 } 5208 tipg |= ipgr1 << E1000_TIPG_IPGR1_SHIFT; 5209 tipg |= ipgr2 << E1000_TIPG_IPGR2_SHIFT; 5210 E1000_WRITE_REG(hw, TIPG, tipg); 5211 /* Program the Transmit Control Register */ 5212 tctl = E1000_READ_REG(hw, TCTL); 5213 tctl &= ~E1000_TCTL_CT; 5214 tctl |= E1000_TCTL_EN | E1000_TCTL_PSP | 5215 (E1000_COLLISION_THRESHOLD << E1000_CT_SHIFT); 5216 5217 if (hw->mac_type == e1000_82571 || hw->mac_type == e1000_82572) { 5218 tarc = E1000_READ_REG(hw, TARC0); 5219 /* set the speed mode bit, we'll clear it if we're not at 5220 * gigabit link later */ 5221 /* git bit can be set to 1*/ 5222 } else if (hw->mac_type == e1000_80003es2lan) { 5223 tarc = E1000_READ_REG(hw, TARC0); 5224 tarc |= 1; 5225 E1000_WRITE_REG(hw, TARC0, tarc); 5226 tarc = E1000_READ_REG(hw, TARC1); 5227 tarc |= 1; 5228 E1000_WRITE_REG(hw, TARC1, tarc); 5229 } 5230 5231 5232 e1000_config_collision_dist(hw); 5233 /* Setup Transmit Descriptor Settings for eop descriptor */ 5234 hw->txd_cmd = E1000_TXD_CMD_EOP | E1000_TXD_CMD_IFCS; 5235 5236 /* Need to set up RS bit */ 5237 if (hw->mac_type < e1000_82543) 5238 hw->txd_cmd |= E1000_TXD_CMD_RPS; 5239 else 5240 hw->txd_cmd |= E1000_TXD_CMD_RS; 5241 5242 5243 if (hw->mac_type == e1000_igb) { 5244 E1000_WRITE_REG(hw, TCTL_EXT, 0x42 << 10); 5245 5246 uint32_t reg_txdctl = E1000_READ_REG(hw, TXDCTL); 5247 reg_txdctl |= 1 << 25; 5248 E1000_WRITE_REG(hw, TXDCTL, reg_txdctl); 5249 mdelay(20); 5250 } 5251 5252 5253 5254 E1000_WRITE_REG(hw, TCTL, tctl); 5255 5256 5257 } 5258 5259 /** 5260 * e1000_setup_rctl - configure the receive control register 5261 * @adapter: Board private structure 5262 **/ 5263 static void 5264 e1000_setup_rctl(struct e1000_hw *hw) 5265 { 5266 uint32_t rctl; 5267 5268 rctl = E1000_READ_REG(hw, RCTL); 5269 5270 rctl &= ~(3 << E1000_RCTL_MO_SHIFT); 5271 5272 rctl |= E1000_RCTL_EN | E1000_RCTL_BAM | E1000_RCTL_LBM_NO 5273 | E1000_RCTL_RDMTS_HALF; /* | 5274 (hw.mc_filter_type << E1000_RCTL_MO_SHIFT); */ 5275 5276 if (hw->tbi_compatibility_on == 1) 5277 rctl |= E1000_RCTL_SBP; 5278 else 5279 rctl &= ~E1000_RCTL_SBP; 5280 5281 rctl &= ~(E1000_RCTL_SZ_4096); 5282 rctl |= E1000_RCTL_SZ_2048; 5283 rctl &= ~(E1000_RCTL_BSEX | E1000_RCTL_LPE); 5284 E1000_WRITE_REG(hw, RCTL, rctl); 5285 } 5286 5287 /** 5288 * e1000_configure_rx - Configure 8254x Receive Unit after Reset 5289 * @adapter: board private structure 5290 * 5291 * Configure the Rx unit of the MAC after a reset. 5292 **/ 5293 static void 5294 e1000_configure_rx(struct e1000_hw *hw) 5295 { 5296 unsigned long rctl, ctrl_ext; 5297 rx_tail = 0; 5298 5299 /* make sure receives are disabled while setting up the descriptors */ 5300 rctl = E1000_READ_REG(hw, RCTL); 5301 E1000_WRITE_REG(hw, RCTL, rctl & ~E1000_RCTL_EN); 5302 if (hw->mac_type >= e1000_82540) { 5303 /* Set the interrupt throttling rate. Value is calculated 5304 * as DEFAULT_ITR = 1/(MAX_INTS_PER_SEC * 256ns) */ 5305 #define MAX_INTS_PER_SEC 8000 5306 #define DEFAULT_ITR 1000000000/(MAX_INTS_PER_SEC * 256) 5307 E1000_WRITE_REG(hw, ITR, DEFAULT_ITR); 5308 } 5309 5310 if (hw->mac_type >= e1000_82571) { 5311 ctrl_ext = E1000_READ_REG(hw, CTRL_EXT); 5312 /* Reset delay timers after every interrupt */ 5313 ctrl_ext |= E1000_CTRL_EXT_INT_TIMER_CLR; 5314 E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext); 5315 E1000_WRITE_FLUSH(hw); 5316 } 5317 /* Setup the Base and Length of the Rx Descriptor Ring */ 5318 E1000_WRITE_REG(hw, RDBAL, lower_32_bits((unsigned long)rx_base)); 5319 E1000_WRITE_REG(hw, RDBAH, upper_32_bits((unsigned long)rx_base)); 5320 5321 E1000_WRITE_REG(hw, RDLEN, 128); 5322 5323 /* Setup the HW Rx Head and Tail Descriptor Pointers */ 5324 E1000_WRITE_REG(hw, RDH, 0); 5325 E1000_WRITE_REG(hw, RDT, 0); 5326 /* Enable Receives */ 5327 5328 if (hw->mac_type == e1000_igb) { 5329 5330 uint32_t reg_rxdctl = E1000_READ_REG(hw, RXDCTL); 5331 reg_rxdctl |= 1 << 25; 5332 E1000_WRITE_REG(hw, RXDCTL, reg_rxdctl); 5333 mdelay(20); 5334 } 5335 5336 E1000_WRITE_REG(hw, RCTL, rctl); 5337 5338 fill_rx(hw); 5339 } 5340 5341 /************************************************************************** 5342 POLL - Wait for a frame 5343 ***************************************************************************/ 5344 static int 5345 _e1000_poll(struct e1000_hw *hw) 5346 { 5347 struct e1000_rx_desc *rd; 5348 unsigned long inval_start, inval_end; 5349 uint32_t len; 5350 5351 /* return true if there's an ethernet packet ready to read */ 5352 rd = rx_base + rx_last; 5353 5354 /* Re-load the descriptor from RAM. */ 5355 inval_start = ((unsigned long)rd) & ~(ARCH_DMA_MINALIGN - 1); 5356 inval_end = inval_start + roundup(sizeof(*rd), ARCH_DMA_MINALIGN); 5357 invalidate_dcache_range(inval_start, inval_end); 5358 5359 if (!(rd->status & E1000_RXD_STAT_DD)) 5360 return 0; 5361 /* DEBUGOUT("recv: packet len=%d\n", rd->length); */ 5362 /* Packet received, make sure the data are re-loaded from RAM. */ 5363 len = le16_to_cpu(rd->length); 5364 invalidate_dcache_range((unsigned long)packet, 5365 (unsigned long)packet + 5366 roundup(len, ARCH_DMA_MINALIGN)); 5367 return len; 5368 } 5369 5370 static int _e1000_transmit(struct e1000_hw *hw, void *txpacket, int length) 5371 { 5372 void *nv_packet = (void *)txpacket; 5373 struct e1000_tx_desc *txp; 5374 int i = 0; 5375 unsigned long flush_start, flush_end; 5376 5377 txp = tx_base + tx_tail; 5378 tx_tail = (tx_tail + 1) % 8; 5379 5380 txp->buffer_addr = cpu_to_le64(virt_to_bus(hw->pdev, nv_packet)); 5381 txp->lower.data = cpu_to_le32(hw->txd_cmd | length); 5382 txp->upper.data = 0; 5383 5384 /* Dump the packet into RAM so e1000 can pick them. */ 5385 flush_dcache_range((unsigned long)nv_packet, 5386 (unsigned long)nv_packet + 5387 roundup(length, ARCH_DMA_MINALIGN)); 5388 /* Dump the descriptor into RAM as well. */ 5389 flush_start = ((unsigned long)txp) & ~(ARCH_DMA_MINALIGN - 1); 5390 flush_end = flush_start + roundup(sizeof(*txp), ARCH_DMA_MINALIGN); 5391 flush_dcache_range(flush_start, flush_end); 5392 5393 E1000_WRITE_REG(hw, TDT, tx_tail); 5394 5395 E1000_WRITE_FLUSH(hw); 5396 while (1) { 5397 invalidate_dcache_range(flush_start, flush_end); 5398 if (le32_to_cpu(txp->upper.data) & E1000_TXD_STAT_DD) 5399 break; 5400 if (i++ > TOUT_LOOP) { 5401 DEBUGOUT("e1000: tx timeout\n"); 5402 return 0; 5403 } 5404 udelay(10); /* give the nic a chance to write to the register */ 5405 } 5406 return 1; 5407 } 5408 5409 static void 5410 _e1000_disable(struct e1000_hw *hw) 5411 { 5412 /* Turn off the ethernet interface */ 5413 E1000_WRITE_REG(hw, RCTL, 0); 5414 E1000_WRITE_REG(hw, TCTL, 0); 5415 5416 /* Clear the transmit ring */ 5417 E1000_WRITE_REG(hw, TDH, 0); 5418 E1000_WRITE_REG(hw, TDT, 0); 5419 5420 /* Clear the receive ring */ 5421 E1000_WRITE_REG(hw, RDH, 0); 5422 E1000_WRITE_REG(hw, RDT, 0); 5423 5424 mdelay(10); 5425 } 5426 5427 /*reset function*/ 5428 static inline int 5429 e1000_reset(struct e1000_hw *hw, unsigned char enetaddr[6]) 5430 { 5431 e1000_reset_hw(hw); 5432 if (hw->mac_type >= e1000_82544) 5433 E1000_WRITE_REG(hw, WUC, 0); 5434 5435 return e1000_init_hw(hw, enetaddr); 5436 } 5437 5438 static int 5439 _e1000_init(struct e1000_hw *hw, unsigned char enetaddr[6]) 5440 { 5441 int ret_val = 0; 5442 5443 ret_val = e1000_reset(hw, enetaddr); 5444 if (ret_val < 0) { 5445 if ((ret_val == -E1000_ERR_NOLINK) || 5446 (ret_val == -E1000_ERR_TIMEOUT)) { 5447 E1000_ERR(hw, "Valid Link not detected: %d\n", ret_val); 5448 } else { 5449 E1000_ERR(hw, "Hardware Initialization Failed\n"); 5450 } 5451 return ret_val; 5452 } 5453 e1000_configure_tx(hw); 5454 e1000_setup_rctl(hw); 5455 e1000_configure_rx(hw); 5456 return 0; 5457 } 5458 5459 /****************************************************************************** 5460 * Gets the current PCI bus type of hardware 5461 * 5462 * hw - Struct containing variables accessed by shared code 5463 *****************************************************************************/ 5464 void e1000_get_bus_type(struct e1000_hw *hw) 5465 { 5466 uint32_t status; 5467 5468 switch (hw->mac_type) { 5469 case e1000_82542_rev2_0: 5470 case e1000_82542_rev2_1: 5471 hw->bus_type = e1000_bus_type_pci; 5472 break; 5473 case e1000_82571: 5474 case e1000_82572: 5475 case e1000_82573: 5476 case e1000_82574: 5477 case e1000_80003es2lan: 5478 case e1000_ich8lan: 5479 case e1000_igb: 5480 hw->bus_type = e1000_bus_type_pci_express; 5481 break; 5482 default: 5483 status = E1000_READ_REG(hw, STATUS); 5484 hw->bus_type = (status & E1000_STATUS_PCIX_MODE) ? 5485 e1000_bus_type_pcix : e1000_bus_type_pci; 5486 break; 5487 } 5488 } 5489 5490 #ifndef CONFIG_DM_ETH 5491 /* A list of all registered e1000 devices */ 5492 static LIST_HEAD(e1000_hw_list); 5493 #endif 5494 5495 #ifdef CONFIG_DM_ETH 5496 static int e1000_init_one(struct e1000_hw *hw, int cardnum, 5497 struct udevice *devno, unsigned char enetaddr[6]) 5498 #else 5499 static int e1000_init_one(struct e1000_hw *hw, int cardnum, pci_dev_t devno, 5500 unsigned char enetaddr[6]) 5501 #endif 5502 { 5503 u32 val; 5504 5505 /* Assign the passed-in values */ 5506 #ifdef CONFIG_DM_ETH 5507 hw->pdev = devno; 5508 #else 5509 hw->pdev = devno; 5510 #endif 5511 hw->cardnum = cardnum; 5512 5513 /* Print a debug message with the IO base address */ 5514 #ifdef CONFIG_DM_ETH 5515 dm_pci_read_config32(devno, PCI_BASE_ADDRESS_0, &val); 5516 #else 5517 pci_read_config_dword(devno, PCI_BASE_ADDRESS_0, &val); 5518 #endif 5519 E1000_DBG(hw, "iobase 0x%08x\n", val & 0xfffffff0); 5520 5521 /* Try to enable I/O accesses and bus-mastering */ 5522 val = PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER; 5523 #ifdef CONFIG_DM_ETH 5524 dm_pci_write_config32(devno, PCI_COMMAND, val); 5525 #else 5526 pci_write_config_dword(devno, PCI_COMMAND, val); 5527 #endif 5528 5529 /* Make sure it worked */ 5530 #ifdef CONFIG_DM_ETH 5531 dm_pci_read_config32(devno, PCI_COMMAND, &val); 5532 #else 5533 pci_read_config_dword(devno, PCI_COMMAND, &val); 5534 #endif 5535 if (!(val & PCI_COMMAND_MEMORY)) { 5536 E1000_ERR(hw, "Can't enable I/O memory\n"); 5537 return -ENOSPC; 5538 } 5539 if (!(val & PCI_COMMAND_MASTER)) { 5540 E1000_ERR(hw, "Can't enable bus-mastering\n"); 5541 return -EPERM; 5542 } 5543 5544 /* Are these variables needed? */ 5545 hw->fc = e1000_fc_default; 5546 hw->original_fc = e1000_fc_default; 5547 hw->autoneg_failed = 0; 5548 hw->autoneg = 1; 5549 hw->get_link_status = true; 5550 #ifndef CONFIG_E1000_NO_NVM 5551 hw->eeprom_semaphore_present = true; 5552 #endif 5553 #ifdef CONFIG_DM_ETH 5554 hw->hw_addr = dm_pci_map_bar(devno, PCI_BASE_ADDRESS_0, 5555 PCI_REGION_MEM); 5556 #else 5557 hw->hw_addr = pci_map_bar(devno, PCI_BASE_ADDRESS_0, 5558 PCI_REGION_MEM); 5559 #endif 5560 hw->mac_type = e1000_undefined; 5561 5562 /* MAC and Phy settings */ 5563 if (e1000_sw_init(hw) < 0) { 5564 E1000_ERR(hw, "Software init failed\n"); 5565 return -EIO; 5566 } 5567 if (e1000_check_phy_reset_block(hw)) 5568 E1000_ERR(hw, "PHY Reset is blocked!\n"); 5569 5570 /* Basic init was OK, reset the hardware and allow SPI access */ 5571 e1000_reset_hw(hw); 5572 5573 #ifndef CONFIG_E1000_NO_NVM 5574 /* Validate the EEPROM and get chipset information */ 5575 if (e1000_init_eeprom_params(hw)) { 5576 E1000_ERR(hw, "EEPROM is invalid!\n"); 5577 return -EINVAL; 5578 } 5579 if ((E1000_READ_REG(hw, I210_EECD) & E1000_EECD_FLUPD) && 5580 e1000_validate_eeprom_checksum(hw)) 5581 return -ENXIO; 5582 e1000_read_mac_addr(hw, enetaddr); 5583 #endif 5584 e1000_get_bus_type(hw); 5585 5586 #ifndef CONFIG_E1000_NO_NVM 5587 printf("e1000: %02x:%02x:%02x:%02x:%02x:%02x\n ", 5588 enetaddr[0], enetaddr[1], enetaddr[2], 5589 enetaddr[3], enetaddr[4], enetaddr[5]); 5590 #else 5591 memset(enetaddr, 0, 6); 5592 printf("e1000: no NVM\n"); 5593 #endif 5594 5595 return 0; 5596 } 5597 5598 /* Put the name of a device in a string */ 5599 static void e1000_name(char *str, int cardnum) 5600 { 5601 sprintf(str, "e1000#%u", cardnum); 5602 } 5603 5604 #ifndef CONFIG_DM_ETH 5605 /************************************************************************** 5606 TRANSMIT - Transmit a frame 5607 ***************************************************************************/ 5608 static int e1000_transmit(struct eth_device *nic, void *txpacket, int length) 5609 { 5610 struct e1000_hw *hw = nic->priv; 5611 5612 return _e1000_transmit(hw, txpacket, length); 5613 } 5614 5615 /************************************************************************** 5616 DISABLE - Turn off ethernet interface 5617 ***************************************************************************/ 5618 static void 5619 e1000_disable(struct eth_device *nic) 5620 { 5621 struct e1000_hw *hw = nic->priv; 5622 5623 _e1000_disable(hw); 5624 } 5625 5626 /************************************************************************** 5627 INIT - set up ethernet interface(s) 5628 ***************************************************************************/ 5629 static int 5630 e1000_init(struct eth_device *nic, bd_t *bis) 5631 { 5632 struct e1000_hw *hw = nic->priv; 5633 5634 return _e1000_init(hw, nic->enetaddr); 5635 } 5636 5637 static int 5638 e1000_poll(struct eth_device *nic) 5639 { 5640 struct e1000_hw *hw = nic->priv; 5641 int len; 5642 5643 len = _e1000_poll(hw); 5644 if (len) { 5645 net_process_received_packet((uchar *)packet, len); 5646 fill_rx(hw); 5647 } 5648 5649 return len ? 1 : 0; 5650 } 5651 5652 static int e1000_write_hwaddr(struct eth_device *dev) 5653 { 5654 #ifndef CONFIG_E1000_NO_NVM 5655 unsigned char *mac = dev->enetaddr; 5656 unsigned char current_mac[6]; 5657 struct e1000_hw *hw = dev->priv; 5658 uint16_t data[3]; 5659 int ret_val, i; 5660 5661 DEBUGOUT("%s: mac=%pM\n", __func__, mac); 5662 5663 memset(current_mac, 0, 6); 5664 5665 /* Read from EEPROM, not from registers, to make sure 5666 * the address is persistently configured 5667 */ 5668 ret_val = e1000_read_mac_addr_from_eeprom(hw, current_mac); 5669 DEBUGOUT("%s: current mac=%pM\n", __func__, current_mac); 5670 5671 /* Only write to EEPROM if the given address is different or 5672 * reading the current address failed 5673 */ 5674 if (!ret_val && memcmp(current_mac, mac, 6) == 0) 5675 return 0; 5676 5677 for (i = 0; i < 3; ++i) 5678 data[i] = mac[i * 2 + 1] << 8 | mac[i * 2]; 5679 5680 ret_val = e1000_write_eeprom_srwr(hw, 0x0, 3, data); 5681 5682 if (!ret_val) 5683 ret_val = e1000_update_eeprom_checksum_i210(hw); 5684 5685 return ret_val; 5686 #else 5687 return 0; 5688 #endif 5689 } 5690 5691 /************************************************************************** 5692 PROBE - Look for an adapter, this routine's visible to the outside 5693 You should omit the last argument struct pci_device * for a non-PCI NIC 5694 ***************************************************************************/ 5695 int 5696 e1000_initialize(bd_t * bis) 5697 { 5698 unsigned int i; 5699 pci_dev_t devno; 5700 int ret; 5701 5702 DEBUGFUNC(); 5703 5704 /* Find and probe all the matching PCI devices */ 5705 for (i = 0; (devno = pci_find_devices(e1000_supported, i)) >= 0; i++) { 5706 /* 5707 * These will never get freed due to errors, this allows us to 5708 * perform SPI EEPROM programming from U-Boot, for example. 5709 */ 5710 struct eth_device *nic = malloc(sizeof(*nic)); 5711 struct e1000_hw *hw = malloc(sizeof(*hw)); 5712 if (!nic || !hw) { 5713 printf("e1000#%u: Out of Memory!\n", i); 5714 free(nic); 5715 free(hw); 5716 continue; 5717 } 5718 5719 /* Make sure all of the fields are initially zeroed */ 5720 memset(nic, 0, sizeof(*nic)); 5721 memset(hw, 0, sizeof(*hw)); 5722 nic->priv = hw; 5723 5724 /* Generate a card name */ 5725 e1000_name(nic->name, i); 5726 hw->name = nic->name; 5727 5728 ret = e1000_init_one(hw, i, devno, nic->enetaddr); 5729 if (ret) 5730 continue; 5731 list_add_tail(&hw->list_node, &e1000_hw_list); 5732 5733 hw->nic = nic; 5734 5735 /* Set up the function pointers and register the device */ 5736 nic->init = e1000_init; 5737 nic->recv = e1000_poll; 5738 nic->send = e1000_transmit; 5739 nic->halt = e1000_disable; 5740 nic->write_hwaddr = e1000_write_hwaddr; 5741 eth_register(nic); 5742 } 5743 5744 return i; 5745 } 5746 5747 struct e1000_hw *e1000_find_card(unsigned int cardnum) 5748 { 5749 struct e1000_hw *hw; 5750 5751 list_for_each_entry(hw, &e1000_hw_list, list_node) 5752 if (hw->cardnum == cardnum) 5753 return hw; 5754 5755 return NULL; 5756 } 5757 #endif /* !CONFIG_DM_ETH */ 5758 5759 #ifdef CONFIG_CMD_E1000 5760 static int do_e1000(cmd_tbl_t *cmdtp, int flag, 5761 int argc, char * const argv[]) 5762 { 5763 unsigned char *mac = NULL; 5764 #ifdef CONFIG_DM_ETH 5765 struct eth_pdata *plat; 5766 struct udevice *dev; 5767 char name[30]; 5768 int ret; 5769 #endif 5770 #if !defined(CONFIG_DM_ETH) || defined(CONFIG_E1000_SPI) 5771 struct e1000_hw *hw; 5772 #endif 5773 int cardnum; 5774 5775 if (argc < 3) { 5776 cmd_usage(cmdtp); 5777 return 1; 5778 } 5779 5780 /* Make sure we can find the requested e1000 card */ 5781 cardnum = simple_strtoul(argv[1], NULL, 10); 5782 #ifdef CONFIG_DM_ETH 5783 e1000_name(name, cardnum); 5784 ret = uclass_get_device_by_name(UCLASS_ETH, name, &dev); 5785 if (!ret) { 5786 plat = dev_get_platdata(dev); 5787 mac = plat->enetaddr; 5788 } 5789 #else 5790 hw = e1000_find_card(cardnum); 5791 if (hw) 5792 mac = hw->nic->enetaddr; 5793 #endif 5794 if (!mac) { 5795 printf("e1000: ERROR: No such device: e1000#%s\n", argv[1]); 5796 return 1; 5797 } 5798 5799 if (!strcmp(argv[2], "print-mac-address")) { 5800 printf("%02x:%02x:%02x:%02x:%02x:%02x\n", 5801 mac[0], mac[1], mac[2], mac[3], mac[4], mac[5]); 5802 return 0; 5803 } 5804 5805 #ifdef CONFIG_E1000_SPI 5806 #ifdef CONFIG_DM_ETH 5807 hw = dev_get_priv(dev); 5808 #endif 5809 /* Handle the "SPI" subcommand */ 5810 if (!strcmp(argv[2], "spi")) 5811 return do_e1000_spi(cmdtp, hw, argc - 3, argv + 3); 5812 #endif 5813 5814 cmd_usage(cmdtp); 5815 return 1; 5816 } 5817 5818 U_BOOT_CMD( 5819 e1000, 7, 0, do_e1000, 5820 "Intel e1000 controller management", 5821 /* */"<card#> print-mac-address\n" 5822 #ifdef CONFIG_E1000_SPI 5823 "e1000 <card#> spi show [<offset> [<length>]]\n" 5824 "e1000 <card#> spi dump <addr> <offset> <length>\n" 5825 "e1000 <card#> spi program <addr> <offset> <length>\n" 5826 "e1000 <card#> spi checksum [update]\n" 5827 #endif 5828 " - Manage the Intel E1000 PCI device" 5829 ); 5830 #endif /* not CONFIG_CMD_E1000 */ 5831 5832 #ifdef CONFIG_DM_ETH 5833 static int e1000_eth_start(struct udevice *dev) 5834 { 5835 struct eth_pdata *plat = dev_get_platdata(dev); 5836 struct e1000_hw *hw = dev_get_priv(dev); 5837 5838 return _e1000_init(hw, plat->enetaddr); 5839 } 5840 5841 static void e1000_eth_stop(struct udevice *dev) 5842 { 5843 struct e1000_hw *hw = dev_get_priv(dev); 5844 5845 _e1000_disable(hw); 5846 } 5847 5848 static int e1000_eth_send(struct udevice *dev, void *packet, int length) 5849 { 5850 struct e1000_hw *hw = dev_get_priv(dev); 5851 int ret; 5852 5853 ret = _e1000_transmit(hw, packet, length); 5854 5855 return ret ? 0 : -ETIMEDOUT; 5856 } 5857 5858 static int e1000_eth_recv(struct udevice *dev, int flags, uchar **packetp) 5859 { 5860 struct e1000_hw *hw = dev_get_priv(dev); 5861 int len; 5862 5863 len = _e1000_poll(hw); 5864 if (len) 5865 *packetp = packet; 5866 5867 return len ? len : -EAGAIN; 5868 } 5869 5870 static int e1000_free_pkt(struct udevice *dev, uchar *packet, int length) 5871 { 5872 struct e1000_hw *hw = dev_get_priv(dev); 5873 5874 fill_rx(hw); 5875 5876 return 0; 5877 } 5878 5879 static int e1000_eth_probe(struct udevice *dev) 5880 { 5881 struct eth_pdata *plat = dev_get_platdata(dev); 5882 struct e1000_hw *hw = dev_get_priv(dev); 5883 int ret; 5884 5885 hw->name = dev->name; 5886 ret = e1000_init_one(hw, trailing_strtol(dev->name), 5887 dev, plat->enetaddr); 5888 if (ret < 0) { 5889 printf(pr_fmt("failed to initialize card: %d\n"), ret); 5890 return ret; 5891 } 5892 5893 return 0; 5894 } 5895 5896 static int e1000_eth_bind(struct udevice *dev) 5897 { 5898 char name[20]; 5899 5900 /* 5901 * A simple way to number the devices. When device tree is used this 5902 * is unnecessary, but when the device is just discovered on the PCI 5903 * bus we need a name. We could instead have the uclass figure out 5904 * which devices are different and number them. 5905 */ 5906 e1000_name(name, num_cards++); 5907 5908 return device_set_name(dev, name); 5909 } 5910 5911 static const struct eth_ops e1000_eth_ops = { 5912 .start = e1000_eth_start, 5913 .send = e1000_eth_send, 5914 .recv = e1000_eth_recv, 5915 .stop = e1000_eth_stop, 5916 .free_pkt = e1000_free_pkt, 5917 }; 5918 5919 static const struct udevice_id e1000_eth_ids[] = { 5920 { .compatible = "intel,e1000" }, 5921 { } 5922 }; 5923 5924 U_BOOT_DRIVER(eth_e1000) = { 5925 .name = "eth_e1000", 5926 .id = UCLASS_ETH, 5927 .of_match = e1000_eth_ids, 5928 .bind = e1000_eth_bind, 5929 .probe = e1000_eth_probe, 5930 .ops = &e1000_eth_ops, 5931 .priv_auto_alloc_size = sizeof(struct e1000_hw), 5932 .platdata_auto_alloc_size = sizeof(struct eth_pdata), 5933 }; 5934 5935 U_BOOT_PCI_DEVICE(eth_e1000, e1000_supported); 5936 #endif 5937