1 /************************************************************************** 2 Intel Pro 1000 for ppcboot/das-u-boot 3 Drivers are port from Intel's Linux driver e1000-4.3.15 4 and from Etherboot pro 1000 driver by mrakes at vivato dot net 5 tested on both gig copper and gig fiber boards 6 ***************************************************************************/ 7 /******************************************************************************* 8 9 10 Copyright(c) 1999 - 2002 Intel Corporation. All rights reserved. 11 12 * SPDX-License-Identifier: GPL-2.0+ 13 14 Contact Information: 15 Linux NICS <linux.nics@intel.com> 16 Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 17 18 *******************************************************************************/ 19 /* 20 * Copyright (C) Archway Digital Solutions. 21 * 22 * written by Chrsitopher Li <cli at arcyway dot com> or <chrisl at gnuchina dot org> 23 * 2/9/2002 24 * 25 * Copyright (C) Linux Networx. 26 * Massive upgrade to work with the new intel gigabit NICs. 27 * <ebiederman at lnxi dot com> 28 * 29 * Copyright 2011 Freescale Semiconductor, Inc. 30 */ 31 32 #include <common.h> 33 #include <dm.h> 34 #include <errno.h> 35 #include <memalign.h> 36 #include <pci.h> 37 #include "e1000.h" 38 39 #define TOUT_LOOP 100000 40 41 #ifdef CONFIG_DM_ETH 42 #define virt_to_bus(devno, v) dm_pci_virt_to_mem(devno, (void *) (v)) 43 #define bus_to_phys(devno, a) dm_pci_mem_to_phys(devno, a) 44 #else 45 #define virt_to_bus(devno, v) pci_virt_to_mem(devno, (void *) (v)) 46 #define bus_to_phys(devno, a) pci_mem_to_phys(devno, a) 47 #endif 48 49 #define E1000_DEFAULT_PCI_PBA 0x00000030 50 #define E1000_DEFAULT_PCIE_PBA 0x000a0026 51 52 /* NIC specific static variables go here */ 53 54 /* Intel i210 needs the DMA descriptor rings aligned to 128b */ 55 #define E1000_BUFFER_ALIGN 128 56 57 /* 58 * TODO(sjg@chromium.org): Even with driver model we share these buffers. 59 * Concurrent receiving on multiple active Ethernet devices will not work. 60 * Normally U-Boot does not support this anyway. To fix it in this driver, 61 * move these buffers and the tx/rx pointers to struct e1000_hw. 62 */ 63 DEFINE_ALIGN_BUFFER(struct e1000_tx_desc, tx_base, 16, E1000_BUFFER_ALIGN); 64 DEFINE_ALIGN_BUFFER(struct e1000_rx_desc, rx_base, 16, E1000_BUFFER_ALIGN); 65 DEFINE_ALIGN_BUFFER(unsigned char, packet, 4096, E1000_BUFFER_ALIGN); 66 67 static int tx_tail; 68 static int rx_tail, rx_last; 69 #ifdef CONFIG_DM_ETH 70 static int num_cards; /* Number of E1000 devices seen so far */ 71 #endif 72 73 static struct pci_device_id e1000_supported[] = { 74 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82542) }, 75 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82543GC_FIBER) }, 76 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82543GC_COPPER) }, 77 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82544EI_COPPER) }, 78 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82544EI_FIBER) }, 79 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82544GC_COPPER) }, 80 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82544GC_LOM) }, 81 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82540EM) }, 82 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82545EM_COPPER) }, 83 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82545GM_COPPER) }, 84 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82546EB_COPPER) }, 85 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82545EM_FIBER) }, 86 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82546EB_FIBER) }, 87 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82546GB_COPPER) }, 88 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82540EM_LOM) }, 89 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82541ER) }, 90 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82541GI_LF) }, 91 /* E1000 PCIe card */ 92 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_COPPER) }, 93 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_FIBER) }, 94 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_SERDES) }, 95 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_QUAD_COPPER) }, 96 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571PT_QUAD_COPPER) }, 97 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_QUAD_FIBER) }, 98 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_QUAD_COPPER_LOWPROFILE) }, 99 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_SERDES_DUAL) }, 100 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_SERDES_QUAD) }, 101 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82572EI_COPPER) }, 102 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82572EI_FIBER) }, 103 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82572EI_SERDES) }, 104 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82572EI) }, 105 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82573E) }, 106 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82573E_IAMT) }, 107 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82573L) }, 108 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82574L) }, 109 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82546GB_QUAD_COPPER_KSP3) }, 110 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80003ES2LAN_COPPER_DPT) }, 111 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80003ES2LAN_SERDES_DPT) }, 112 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80003ES2LAN_COPPER_SPT) }, 113 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80003ES2LAN_SERDES_SPT) }, 114 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_I210_UNPROGRAMMED) }, 115 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_I211_UNPROGRAMMED) }, 116 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_I210_COPPER) }, 117 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_I211_COPPER) }, 118 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_I210_COPPER_FLASHLESS) }, 119 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_I210_SERDES) }, 120 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_I210_SERDES_FLASHLESS) }, 121 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_I210_1000BASEKX) }, 122 123 {} 124 }; 125 126 /* Function forward declarations */ 127 static int e1000_setup_link(struct e1000_hw *hw); 128 static int e1000_setup_fiber_link(struct e1000_hw *hw); 129 static int e1000_setup_copper_link(struct e1000_hw *hw); 130 static int e1000_phy_setup_autoneg(struct e1000_hw *hw); 131 static void e1000_config_collision_dist(struct e1000_hw *hw); 132 static int e1000_config_mac_to_phy(struct e1000_hw *hw); 133 static int e1000_config_fc_after_link_up(struct e1000_hw *hw); 134 static int e1000_check_for_link(struct e1000_hw *hw); 135 static int e1000_wait_autoneg(struct e1000_hw *hw); 136 static int e1000_get_speed_and_duplex(struct e1000_hw *hw, uint16_t * speed, 137 uint16_t * duplex); 138 static int e1000_read_phy_reg(struct e1000_hw *hw, uint32_t reg_addr, 139 uint16_t * phy_data); 140 static int e1000_write_phy_reg(struct e1000_hw *hw, uint32_t reg_addr, 141 uint16_t phy_data); 142 static int32_t e1000_phy_hw_reset(struct e1000_hw *hw); 143 static int e1000_phy_reset(struct e1000_hw *hw); 144 static int e1000_detect_gig_phy(struct e1000_hw *hw); 145 static void e1000_set_media_type(struct e1000_hw *hw); 146 147 static int32_t e1000_swfw_sync_acquire(struct e1000_hw *hw, uint16_t mask); 148 static void e1000_swfw_sync_release(struct e1000_hw *hw, uint16_t mask); 149 static int32_t e1000_check_phy_reset_block(struct e1000_hw *hw); 150 151 #ifndef CONFIG_E1000_NO_NVM 152 static void e1000_put_hw_eeprom_semaphore(struct e1000_hw *hw); 153 static int32_t e1000_read_eeprom(struct e1000_hw *hw, uint16_t offset, 154 uint16_t words, 155 uint16_t *data); 156 /****************************************************************************** 157 * Raises the EEPROM's clock input. 158 * 159 * hw - Struct containing variables accessed by shared code 160 * eecd - EECD's current value 161 *****************************************************************************/ 162 void e1000_raise_ee_clk(struct e1000_hw *hw, uint32_t * eecd) 163 { 164 /* Raise the clock input to the EEPROM (by setting the SK bit), and then 165 * wait 50 microseconds. 166 */ 167 *eecd = *eecd | E1000_EECD_SK; 168 E1000_WRITE_REG(hw, EECD, *eecd); 169 E1000_WRITE_FLUSH(hw); 170 udelay(50); 171 } 172 173 /****************************************************************************** 174 * Lowers the EEPROM's clock input. 175 * 176 * hw - Struct containing variables accessed by shared code 177 * eecd - EECD's current value 178 *****************************************************************************/ 179 void e1000_lower_ee_clk(struct e1000_hw *hw, uint32_t * eecd) 180 { 181 /* Lower the clock input to the EEPROM (by clearing the SK bit), and then 182 * wait 50 microseconds. 183 */ 184 *eecd = *eecd & ~E1000_EECD_SK; 185 E1000_WRITE_REG(hw, EECD, *eecd); 186 E1000_WRITE_FLUSH(hw); 187 udelay(50); 188 } 189 190 /****************************************************************************** 191 * Shift data bits out to the EEPROM. 192 * 193 * hw - Struct containing variables accessed by shared code 194 * data - data to send to the EEPROM 195 * count - number of bits to shift out 196 *****************************************************************************/ 197 static void 198 e1000_shift_out_ee_bits(struct e1000_hw *hw, uint16_t data, uint16_t count) 199 { 200 uint32_t eecd; 201 uint32_t mask; 202 203 /* We need to shift "count" bits out to the EEPROM. So, value in the 204 * "data" parameter will be shifted out to the EEPROM one bit at a time. 205 * In order to do this, "data" must be broken down into bits. 206 */ 207 mask = 0x01 << (count - 1); 208 eecd = E1000_READ_REG(hw, EECD); 209 eecd &= ~(E1000_EECD_DO | E1000_EECD_DI); 210 do { 211 /* A "1" is shifted out to the EEPROM by setting bit "DI" to a "1", 212 * and then raising and then lowering the clock (the SK bit controls 213 * the clock input to the EEPROM). A "0" is shifted out to the EEPROM 214 * by setting "DI" to "0" and then raising and then lowering the clock. 215 */ 216 eecd &= ~E1000_EECD_DI; 217 218 if (data & mask) 219 eecd |= E1000_EECD_DI; 220 221 E1000_WRITE_REG(hw, EECD, eecd); 222 E1000_WRITE_FLUSH(hw); 223 224 udelay(50); 225 226 e1000_raise_ee_clk(hw, &eecd); 227 e1000_lower_ee_clk(hw, &eecd); 228 229 mask = mask >> 1; 230 231 } while (mask); 232 233 /* We leave the "DI" bit set to "0" when we leave this routine. */ 234 eecd &= ~E1000_EECD_DI; 235 E1000_WRITE_REG(hw, EECD, eecd); 236 } 237 238 /****************************************************************************** 239 * Shift data bits in from the EEPROM 240 * 241 * hw - Struct containing variables accessed by shared code 242 *****************************************************************************/ 243 static uint16_t 244 e1000_shift_in_ee_bits(struct e1000_hw *hw, uint16_t count) 245 { 246 uint32_t eecd; 247 uint32_t i; 248 uint16_t data; 249 250 /* In order to read a register from the EEPROM, we need to shift 'count' 251 * bits in from the EEPROM. Bits are "shifted in" by raising the clock 252 * input to the EEPROM (setting the SK bit), and then reading the 253 * value of the "DO" bit. During this "shifting in" process the 254 * "DI" bit should always be clear. 255 */ 256 257 eecd = E1000_READ_REG(hw, EECD); 258 259 eecd &= ~(E1000_EECD_DO | E1000_EECD_DI); 260 data = 0; 261 262 for (i = 0; i < count; i++) { 263 data = data << 1; 264 e1000_raise_ee_clk(hw, &eecd); 265 266 eecd = E1000_READ_REG(hw, EECD); 267 268 eecd &= ~(E1000_EECD_DI); 269 if (eecd & E1000_EECD_DO) 270 data |= 1; 271 272 e1000_lower_ee_clk(hw, &eecd); 273 } 274 275 return data; 276 } 277 278 /****************************************************************************** 279 * Returns EEPROM to a "standby" state 280 * 281 * hw - Struct containing variables accessed by shared code 282 *****************************************************************************/ 283 void e1000_standby_eeprom(struct e1000_hw *hw) 284 { 285 struct e1000_eeprom_info *eeprom = &hw->eeprom; 286 uint32_t eecd; 287 288 eecd = E1000_READ_REG(hw, EECD); 289 290 if (eeprom->type == e1000_eeprom_microwire) { 291 eecd &= ~(E1000_EECD_CS | E1000_EECD_SK); 292 E1000_WRITE_REG(hw, EECD, eecd); 293 E1000_WRITE_FLUSH(hw); 294 udelay(eeprom->delay_usec); 295 296 /* Clock high */ 297 eecd |= E1000_EECD_SK; 298 E1000_WRITE_REG(hw, EECD, eecd); 299 E1000_WRITE_FLUSH(hw); 300 udelay(eeprom->delay_usec); 301 302 /* Select EEPROM */ 303 eecd |= E1000_EECD_CS; 304 E1000_WRITE_REG(hw, EECD, eecd); 305 E1000_WRITE_FLUSH(hw); 306 udelay(eeprom->delay_usec); 307 308 /* Clock low */ 309 eecd &= ~E1000_EECD_SK; 310 E1000_WRITE_REG(hw, EECD, eecd); 311 E1000_WRITE_FLUSH(hw); 312 udelay(eeprom->delay_usec); 313 } else if (eeprom->type == e1000_eeprom_spi) { 314 /* Toggle CS to flush commands */ 315 eecd |= E1000_EECD_CS; 316 E1000_WRITE_REG(hw, EECD, eecd); 317 E1000_WRITE_FLUSH(hw); 318 udelay(eeprom->delay_usec); 319 eecd &= ~E1000_EECD_CS; 320 E1000_WRITE_REG(hw, EECD, eecd); 321 E1000_WRITE_FLUSH(hw); 322 udelay(eeprom->delay_usec); 323 } 324 } 325 326 /*************************************************************************** 327 * Description: Determines if the onboard NVM is FLASH or EEPROM. 328 * 329 * hw - Struct containing variables accessed by shared code 330 ****************************************************************************/ 331 static bool e1000_is_onboard_nvm_eeprom(struct e1000_hw *hw) 332 { 333 uint32_t eecd = 0; 334 335 DEBUGFUNC(); 336 337 if (hw->mac_type == e1000_ich8lan) 338 return false; 339 340 if (hw->mac_type == e1000_82573 || hw->mac_type == e1000_82574) { 341 eecd = E1000_READ_REG(hw, EECD); 342 343 /* Isolate bits 15 & 16 */ 344 eecd = ((eecd >> 15) & 0x03); 345 346 /* If both bits are set, device is Flash type */ 347 if (eecd == 0x03) 348 return false; 349 } 350 return true; 351 } 352 353 /****************************************************************************** 354 * Prepares EEPROM for access 355 * 356 * hw - Struct containing variables accessed by shared code 357 * 358 * Lowers EEPROM clock. Clears input pin. Sets the chip select pin. This 359 * function should be called before issuing a command to the EEPROM. 360 *****************************************************************************/ 361 int32_t e1000_acquire_eeprom(struct e1000_hw *hw) 362 { 363 struct e1000_eeprom_info *eeprom = &hw->eeprom; 364 uint32_t eecd, i = 0; 365 366 DEBUGFUNC(); 367 368 if (e1000_swfw_sync_acquire(hw, E1000_SWFW_EEP_SM)) 369 return -E1000_ERR_SWFW_SYNC; 370 eecd = E1000_READ_REG(hw, EECD); 371 372 if (hw->mac_type != e1000_82573 && hw->mac_type != e1000_82574) { 373 /* Request EEPROM Access */ 374 if (hw->mac_type > e1000_82544) { 375 eecd |= E1000_EECD_REQ; 376 E1000_WRITE_REG(hw, EECD, eecd); 377 eecd = E1000_READ_REG(hw, EECD); 378 while ((!(eecd & E1000_EECD_GNT)) && 379 (i < E1000_EEPROM_GRANT_ATTEMPTS)) { 380 i++; 381 udelay(5); 382 eecd = E1000_READ_REG(hw, EECD); 383 } 384 if (!(eecd & E1000_EECD_GNT)) { 385 eecd &= ~E1000_EECD_REQ; 386 E1000_WRITE_REG(hw, EECD, eecd); 387 DEBUGOUT("Could not acquire EEPROM grant\n"); 388 return -E1000_ERR_EEPROM; 389 } 390 } 391 } 392 393 /* Setup EEPROM for Read/Write */ 394 395 if (eeprom->type == e1000_eeprom_microwire) { 396 /* Clear SK and DI */ 397 eecd &= ~(E1000_EECD_DI | E1000_EECD_SK); 398 E1000_WRITE_REG(hw, EECD, eecd); 399 400 /* Set CS */ 401 eecd |= E1000_EECD_CS; 402 E1000_WRITE_REG(hw, EECD, eecd); 403 } else if (eeprom->type == e1000_eeprom_spi) { 404 /* Clear SK and CS */ 405 eecd &= ~(E1000_EECD_CS | E1000_EECD_SK); 406 E1000_WRITE_REG(hw, EECD, eecd); 407 udelay(1); 408 } 409 410 return E1000_SUCCESS; 411 } 412 413 /****************************************************************************** 414 * Sets up eeprom variables in the hw struct. Must be called after mac_type 415 * is configured. Additionally, if this is ICH8, the flash controller GbE 416 * registers must be mapped, or this will crash. 417 * 418 * hw - Struct containing variables accessed by shared code 419 *****************************************************************************/ 420 static int32_t e1000_init_eeprom_params(struct e1000_hw *hw) 421 { 422 struct e1000_eeprom_info *eeprom = &hw->eeprom; 423 uint32_t eecd; 424 int32_t ret_val = E1000_SUCCESS; 425 uint16_t eeprom_size; 426 427 if (hw->mac_type == e1000_igb) 428 eecd = E1000_READ_REG(hw, I210_EECD); 429 else 430 eecd = E1000_READ_REG(hw, EECD); 431 432 DEBUGFUNC(); 433 434 switch (hw->mac_type) { 435 case e1000_82542_rev2_0: 436 case e1000_82542_rev2_1: 437 case e1000_82543: 438 case e1000_82544: 439 eeprom->type = e1000_eeprom_microwire; 440 eeprom->word_size = 64; 441 eeprom->opcode_bits = 3; 442 eeprom->address_bits = 6; 443 eeprom->delay_usec = 50; 444 eeprom->use_eerd = false; 445 eeprom->use_eewr = false; 446 break; 447 case e1000_82540: 448 case e1000_82545: 449 case e1000_82545_rev_3: 450 case e1000_82546: 451 case e1000_82546_rev_3: 452 eeprom->type = e1000_eeprom_microwire; 453 eeprom->opcode_bits = 3; 454 eeprom->delay_usec = 50; 455 if (eecd & E1000_EECD_SIZE) { 456 eeprom->word_size = 256; 457 eeprom->address_bits = 8; 458 } else { 459 eeprom->word_size = 64; 460 eeprom->address_bits = 6; 461 } 462 eeprom->use_eerd = false; 463 eeprom->use_eewr = false; 464 break; 465 case e1000_82541: 466 case e1000_82541_rev_2: 467 case e1000_82547: 468 case e1000_82547_rev_2: 469 if (eecd & E1000_EECD_TYPE) { 470 eeprom->type = e1000_eeprom_spi; 471 eeprom->opcode_bits = 8; 472 eeprom->delay_usec = 1; 473 if (eecd & E1000_EECD_ADDR_BITS) { 474 eeprom->page_size = 32; 475 eeprom->address_bits = 16; 476 } else { 477 eeprom->page_size = 8; 478 eeprom->address_bits = 8; 479 } 480 } else { 481 eeprom->type = e1000_eeprom_microwire; 482 eeprom->opcode_bits = 3; 483 eeprom->delay_usec = 50; 484 if (eecd & E1000_EECD_ADDR_BITS) { 485 eeprom->word_size = 256; 486 eeprom->address_bits = 8; 487 } else { 488 eeprom->word_size = 64; 489 eeprom->address_bits = 6; 490 } 491 } 492 eeprom->use_eerd = false; 493 eeprom->use_eewr = false; 494 break; 495 case e1000_82571: 496 case e1000_82572: 497 eeprom->type = e1000_eeprom_spi; 498 eeprom->opcode_bits = 8; 499 eeprom->delay_usec = 1; 500 if (eecd & E1000_EECD_ADDR_BITS) { 501 eeprom->page_size = 32; 502 eeprom->address_bits = 16; 503 } else { 504 eeprom->page_size = 8; 505 eeprom->address_bits = 8; 506 } 507 eeprom->use_eerd = false; 508 eeprom->use_eewr = false; 509 break; 510 case e1000_82573: 511 case e1000_82574: 512 eeprom->type = e1000_eeprom_spi; 513 eeprom->opcode_bits = 8; 514 eeprom->delay_usec = 1; 515 if (eecd & E1000_EECD_ADDR_BITS) { 516 eeprom->page_size = 32; 517 eeprom->address_bits = 16; 518 } else { 519 eeprom->page_size = 8; 520 eeprom->address_bits = 8; 521 } 522 if (e1000_is_onboard_nvm_eeprom(hw) == false) { 523 eeprom->use_eerd = true; 524 eeprom->use_eewr = true; 525 526 eeprom->type = e1000_eeprom_flash; 527 eeprom->word_size = 2048; 528 529 /* Ensure that the Autonomous FLASH update bit is cleared due to 530 * Flash update issue on parts which use a FLASH for NVM. */ 531 eecd &= ~E1000_EECD_AUPDEN; 532 E1000_WRITE_REG(hw, EECD, eecd); 533 } 534 break; 535 case e1000_80003es2lan: 536 eeprom->type = e1000_eeprom_spi; 537 eeprom->opcode_bits = 8; 538 eeprom->delay_usec = 1; 539 if (eecd & E1000_EECD_ADDR_BITS) { 540 eeprom->page_size = 32; 541 eeprom->address_bits = 16; 542 } else { 543 eeprom->page_size = 8; 544 eeprom->address_bits = 8; 545 } 546 eeprom->use_eerd = true; 547 eeprom->use_eewr = false; 548 break; 549 case e1000_igb: 550 /* i210 has 4k of iNVM mapped as EEPROM */ 551 eeprom->type = e1000_eeprom_invm; 552 eeprom->opcode_bits = 8; 553 eeprom->delay_usec = 1; 554 eeprom->page_size = 32; 555 eeprom->address_bits = 16; 556 eeprom->use_eerd = true; 557 eeprom->use_eewr = false; 558 break; 559 default: 560 break; 561 } 562 563 if (eeprom->type == e1000_eeprom_spi || 564 eeprom->type == e1000_eeprom_invm) { 565 /* eeprom_size will be an enum [0..8] that maps 566 * to eeprom sizes 128B to 567 * 32KB (incremented by powers of 2). 568 */ 569 if (hw->mac_type <= e1000_82547_rev_2) { 570 /* Set to default value for initial eeprom read. */ 571 eeprom->word_size = 64; 572 ret_val = e1000_read_eeprom(hw, EEPROM_CFG, 1, 573 &eeprom_size); 574 if (ret_val) 575 return ret_val; 576 eeprom_size = (eeprom_size & EEPROM_SIZE_MASK) 577 >> EEPROM_SIZE_SHIFT; 578 /* 256B eeprom size was not supported in earlier 579 * hardware, so we bump eeprom_size up one to 580 * ensure that "1" (which maps to 256B) is never 581 * the result used in the shifting logic below. */ 582 if (eeprom_size) 583 eeprom_size++; 584 } else { 585 eeprom_size = (uint16_t)((eecd & 586 E1000_EECD_SIZE_EX_MASK) >> 587 E1000_EECD_SIZE_EX_SHIFT); 588 } 589 590 eeprom->word_size = 1 << (eeprom_size + EEPROM_WORD_SIZE_SHIFT); 591 } 592 return ret_val; 593 } 594 595 /****************************************************************************** 596 * Polls the status bit (bit 1) of the EERD to determine when the read is done. 597 * 598 * hw - Struct containing variables accessed by shared code 599 *****************************************************************************/ 600 static int32_t 601 e1000_poll_eerd_eewr_done(struct e1000_hw *hw, int eerd) 602 { 603 uint32_t attempts = 100000; 604 uint32_t i, reg = 0; 605 int32_t done = E1000_ERR_EEPROM; 606 607 for (i = 0; i < attempts; i++) { 608 if (eerd == E1000_EEPROM_POLL_READ) { 609 if (hw->mac_type == e1000_igb) 610 reg = E1000_READ_REG(hw, I210_EERD); 611 else 612 reg = E1000_READ_REG(hw, EERD); 613 } else { 614 if (hw->mac_type == e1000_igb) 615 reg = E1000_READ_REG(hw, I210_EEWR); 616 else 617 reg = E1000_READ_REG(hw, EEWR); 618 } 619 620 if (reg & E1000_EEPROM_RW_REG_DONE) { 621 done = E1000_SUCCESS; 622 break; 623 } 624 udelay(5); 625 } 626 627 return done; 628 } 629 630 /****************************************************************************** 631 * Reads a 16 bit word from the EEPROM using the EERD register. 632 * 633 * hw - Struct containing variables accessed by shared code 634 * offset - offset of word in the EEPROM to read 635 * data - word read from the EEPROM 636 * words - number of words to read 637 *****************************************************************************/ 638 static int32_t 639 e1000_read_eeprom_eerd(struct e1000_hw *hw, 640 uint16_t offset, 641 uint16_t words, 642 uint16_t *data) 643 { 644 uint32_t i, eerd = 0; 645 int32_t error = 0; 646 647 for (i = 0; i < words; i++) { 648 eerd = ((offset+i) << E1000_EEPROM_RW_ADDR_SHIFT) + 649 E1000_EEPROM_RW_REG_START; 650 651 if (hw->mac_type == e1000_igb) 652 E1000_WRITE_REG(hw, I210_EERD, eerd); 653 else 654 E1000_WRITE_REG(hw, EERD, eerd); 655 656 error = e1000_poll_eerd_eewr_done(hw, E1000_EEPROM_POLL_READ); 657 658 if (error) 659 break; 660 661 if (hw->mac_type == e1000_igb) { 662 data[i] = (E1000_READ_REG(hw, I210_EERD) >> 663 E1000_EEPROM_RW_REG_DATA); 664 } else { 665 data[i] = (E1000_READ_REG(hw, EERD) >> 666 E1000_EEPROM_RW_REG_DATA); 667 } 668 669 } 670 671 return error; 672 } 673 674 void e1000_release_eeprom(struct e1000_hw *hw) 675 { 676 uint32_t eecd; 677 678 DEBUGFUNC(); 679 680 eecd = E1000_READ_REG(hw, EECD); 681 682 if (hw->eeprom.type == e1000_eeprom_spi) { 683 eecd |= E1000_EECD_CS; /* Pull CS high */ 684 eecd &= ~E1000_EECD_SK; /* Lower SCK */ 685 686 E1000_WRITE_REG(hw, EECD, eecd); 687 688 udelay(hw->eeprom.delay_usec); 689 } else if (hw->eeprom.type == e1000_eeprom_microwire) { 690 /* cleanup eeprom */ 691 692 /* CS on Microwire is active-high */ 693 eecd &= ~(E1000_EECD_CS | E1000_EECD_DI); 694 695 E1000_WRITE_REG(hw, EECD, eecd); 696 697 /* Rising edge of clock */ 698 eecd |= E1000_EECD_SK; 699 E1000_WRITE_REG(hw, EECD, eecd); 700 E1000_WRITE_FLUSH(hw); 701 udelay(hw->eeprom.delay_usec); 702 703 /* Falling edge of clock */ 704 eecd &= ~E1000_EECD_SK; 705 E1000_WRITE_REG(hw, EECD, eecd); 706 E1000_WRITE_FLUSH(hw); 707 udelay(hw->eeprom.delay_usec); 708 } 709 710 /* Stop requesting EEPROM access */ 711 if (hw->mac_type > e1000_82544) { 712 eecd &= ~E1000_EECD_REQ; 713 E1000_WRITE_REG(hw, EECD, eecd); 714 } 715 716 e1000_swfw_sync_release(hw, E1000_SWFW_EEP_SM); 717 } 718 719 /****************************************************************************** 720 * Reads a 16 bit word from the EEPROM. 721 * 722 * hw - Struct containing variables accessed by shared code 723 *****************************************************************************/ 724 static int32_t 725 e1000_spi_eeprom_ready(struct e1000_hw *hw) 726 { 727 uint16_t retry_count = 0; 728 uint8_t spi_stat_reg; 729 730 DEBUGFUNC(); 731 732 /* Read "Status Register" repeatedly until the LSB is cleared. The 733 * EEPROM will signal that the command has been completed by clearing 734 * bit 0 of the internal status register. If it's not cleared within 735 * 5 milliseconds, then error out. 736 */ 737 retry_count = 0; 738 do { 739 e1000_shift_out_ee_bits(hw, EEPROM_RDSR_OPCODE_SPI, 740 hw->eeprom.opcode_bits); 741 spi_stat_reg = (uint8_t)e1000_shift_in_ee_bits(hw, 8); 742 if (!(spi_stat_reg & EEPROM_STATUS_RDY_SPI)) 743 break; 744 745 udelay(5); 746 retry_count += 5; 747 748 e1000_standby_eeprom(hw); 749 } while (retry_count < EEPROM_MAX_RETRY_SPI); 750 751 /* ATMEL SPI write time could vary from 0-20mSec on 3.3V devices (and 752 * only 0-5mSec on 5V devices) 753 */ 754 if (retry_count >= EEPROM_MAX_RETRY_SPI) { 755 DEBUGOUT("SPI EEPROM Status error\n"); 756 return -E1000_ERR_EEPROM; 757 } 758 759 return E1000_SUCCESS; 760 } 761 762 /****************************************************************************** 763 * Reads a 16 bit word from the EEPROM. 764 * 765 * hw - Struct containing variables accessed by shared code 766 * offset - offset of word in the EEPROM to read 767 * data - word read from the EEPROM 768 *****************************************************************************/ 769 static int32_t 770 e1000_read_eeprom(struct e1000_hw *hw, uint16_t offset, 771 uint16_t words, uint16_t *data) 772 { 773 struct e1000_eeprom_info *eeprom = &hw->eeprom; 774 uint32_t i = 0; 775 776 DEBUGFUNC(); 777 778 /* If eeprom is not yet detected, do so now */ 779 if (eeprom->word_size == 0) 780 e1000_init_eeprom_params(hw); 781 782 /* A check for invalid values: offset too large, too many words, 783 * and not enough words. 784 */ 785 if ((offset >= eeprom->word_size) || 786 (words > eeprom->word_size - offset) || 787 (words == 0)) { 788 DEBUGOUT("\"words\" parameter out of bounds." 789 "Words = %d, size = %d\n", offset, eeprom->word_size); 790 return -E1000_ERR_EEPROM; 791 } 792 793 /* EEPROM's that don't use EERD to read require us to bit-bang the SPI 794 * directly. In this case, we need to acquire the EEPROM so that 795 * FW or other port software does not interrupt. 796 */ 797 if (e1000_is_onboard_nvm_eeprom(hw) == true && 798 hw->eeprom.use_eerd == false) { 799 800 /* Prepare the EEPROM for bit-bang reading */ 801 if (e1000_acquire_eeprom(hw) != E1000_SUCCESS) 802 return -E1000_ERR_EEPROM; 803 } 804 805 /* Eerd register EEPROM access requires no eeprom aquire/release */ 806 if (eeprom->use_eerd == true) 807 return e1000_read_eeprom_eerd(hw, offset, words, data); 808 809 /* Set up the SPI or Microwire EEPROM for bit-bang reading. We have 810 * acquired the EEPROM at this point, so any returns should relase it */ 811 if (eeprom->type == e1000_eeprom_spi) { 812 uint16_t word_in; 813 uint8_t read_opcode = EEPROM_READ_OPCODE_SPI; 814 815 if (e1000_spi_eeprom_ready(hw)) { 816 e1000_release_eeprom(hw); 817 return -E1000_ERR_EEPROM; 818 } 819 820 e1000_standby_eeprom(hw); 821 822 /* Some SPI eeproms use the 8th address bit embedded in 823 * the opcode */ 824 if ((eeprom->address_bits == 8) && (offset >= 128)) 825 read_opcode |= EEPROM_A8_OPCODE_SPI; 826 827 /* Send the READ command (opcode + addr) */ 828 e1000_shift_out_ee_bits(hw, read_opcode, eeprom->opcode_bits); 829 e1000_shift_out_ee_bits(hw, (uint16_t)(offset*2), 830 eeprom->address_bits); 831 832 /* Read the data. The address of the eeprom internally 833 * increments with each byte (spi) being read, saving on the 834 * overhead of eeprom setup and tear-down. The address 835 * counter will roll over if reading beyond the size of 836 * the eeprom, thus allowing the entire memory to be read 837 * starting from any offset. */ 838 for (i = 0; i < words; i++) { 839 word_in = e1000_shift_in_ee_bits(hw, 16); 840 data[i] = (word_in >> 8) | (word_in << 8); 841 } 842 } else if (eeprom->type == e1000_eeprom_microwire) { 843 for (i = 0; i < words; i++) { 844 /* Send the READ command (opcode + addr) */ 845 e1000_shift_out_ee_bits(hw, 846 EEPROM_READ_OPCODE_MICROWIRE, 847 eeprom->opcode_bits); 848 e1000_shift_out_ee_bits(hw, (uint16_t)(offset + i), 849 eeprom->address_bits); 850 851 /* Read the data. For microwire, each word requires 852 * the overhead of eeprom setup and tear-down. */ 853 data[i] = e1000_shift_in_ee_bits(hw, 16); 854 e1000_standby_eeprom(hw); 855 } 856 } 857 858 /* End this read operation */ 859 e1000_release_eeprom(hw); 860 861 return E1000_SUCCESS; 862 } 863 864 /****************************************************************************** 865 * Verifies that the EEPROM has a valid checksum 866 * 867 * hw - Struct containing variables accessed by shared code 868 * 869 * Reads the first 64 16 bit words of the EEPROM and sums the values read. 870 * If the the sum of the 64 16 bit words is 0xBABA, the EEPROM's checksum is 871 * valid. 872 *****************************************************************************/ 873 static int e1000_validate_eeprom_checksum(struct e1000_hw *hw) 874 { 875 uint16_t i, checksum, checksum_reg, *buf; 876 877 DEBUGFUNC(); 878 879 /* Allocate a temporary buffer */ 880 buf = malloc(sizeof(buf[0]) * (EEPROM_CHECKSUM_REG + 1)); 881 if (!buf) { 882 E1000_ERR(hw, "Unable to allocate EEPROM buffer!\n"); 883 return -E1000_ERR_EEPROM; 884 } 885 886 /* Read the EEPROM */ 887 if (e1000_read_eeprom(hw, 0, EEPROM_CHECKSUM_REG + 1, buf) < 0) { 888 E1000_ERR(hw, "Unable to read EEPROM!\n"); 889 return -E1000_ERR_EEPROM; 890 } 891 892 /* Compute the checksum */ 893 checksum = 0; 894 for (i = 0; i < EEPROM_CHECKSUM_REG; i++) 895 checksum += buf[i]; 896 checksum = ((uint16_t)EEPROM_SUM) - checksum; 897 checksum_reg = buf[i]; 898 899 /* Verify it! */ 900 if (checksum == checksum_reg) 901 return 0; 902 903 /* Hrm, verification failed, print an error */ 904 E1000_ERR(hw, "EEPROM checksum is incorrect!\n"); 905 E1000_ERR(hw, " ...register was 0x%04hx, calculated 0x%04hx\n", 906 checksum_reg, checksum); 907 908 return -E1000_ERR_EEPROM; 909 } 910 #endif /* CONFIG_E1000_NO_NVM */ 911 912 /***************************************************************************** 913 * Set PHY to class A mode 914 * Assumes the following operations will follow to enable the new class mode. 915 * 1. Do a PHY soft reset 916 * 2. Restart auto-negotiation or force link. 917 * 918 * hw - Struct containing variables accessed by shared code 919 ****************************************************************************/ 920 static int32_t 921 e1000_set_phy_mode(struct e1000_hw *hw) 922 { 923 #ifndef CONFIG_E1000_NO_NVM 924 int32_t ret_val; 925 uint16_t eeprom_data; 926 927 DEBUGFUNC(); 928 929 if ((hw->mac_type == e1000_82545_rev_3) && 930 (hw->media_type == e1000_media_type_copper)) { 931 ret_val = e1000_read_eeprom(hw, EEPROM_PHY_CLASS_WORD, 932 1, &eeprom_data); 933 if (ret_val) 934 return ret_val; 935 936 if ((eeprom_data != EEPROM_RESERVED_WORD) && 937 (eeprom_data & EEPROM_PHY_CLASS_A)) { 938 ret_val = e1000_write_phy_reg(hw, 939 M88E1000_PHY_PAGE_SELECT, 0x000B); 940 if (ret_val) 941 return ret_val; 942 ret_val = e1000_write_phy_reg(hw, 943 M88E1000_PHY_GEN_CONTROL, 0x8104); 944 if (ret_val) 945 return ret_val; 946 947 hw->phy_reset_disable = false; 948 } 949 } 950 #endif 951 return E1000_SUCCESS; 952 } 953 954 #ifndef CONFIG_E1000_NO_NVM 955 /*************************************************************************** 956 * 957 * Obtaining software semaphore bit (SMBI) before resetting PHY. 958 * 959 * hw: Struct containing variables accessed by shared code 960 * 961 * returns: - E1000_ERR_RESET if fail to obtain semaphore. 962 * E1000_SUCCESS at any other case. 963 * 964 ***************************************************************************/ 965 static int32_t 966 e1000_get_software_semaphore(struct e1000_hw *hw) 967 { 968 int32_t timeout = hw->eeprom.word_size + 1; 969 uint32_t swsm; 970 971 DEBUGFUNC(); 972 973 if (hw->mac_type != e1000_80003es2lan) 974 return E1000_SUCCESS; 975 976 while (timeout) { 977 swsm = E1000_READ_REG(hw, SWSM); 978 /* If SMBI bit cleared, it is now set and we hold 979 * the semaphore */ 980 if (!(swsm & E1000_SWSM_SMBI)) 981 break; 982 mdelay(1); 983 timeout--; 984 } 985 986 if (!timeout) { 987 DEBUGOUT("Driver can't access device - SMBI bit is set.\n"); 988 return -E1000_ERR_RESET; 989 } 990 991 return E1000_SUCCESS; 992 } 993 #endif 994 995 /*************************************************************************** 996 * This function clears HW semaphore bits. 997 * 998 * hw: Struct containing variables accessed by shared code 999 * 1000 * returns: - None. 1001 * 1002 ***************************************************************************/ 1003 static void 1004 e1000_put_hw_eeprom_semaphore(struct e1000_hw *hw) 1005 { 1006 #ifndef CONFIG_E1000_NO_NVM 1007 uint32_t swsm; 1008 1009 DEBUGFUNC(); 1010 1011 if (!hw->eeprom_semaphore_present) 1012 return; 1013 1014 swsm = E1000_READ_REG(hw, SWSM); 1015 if (hw->mac_type == e1000_80003es2lan) { 1016 /* Release both semaphores. */ 1017 swsm &= ~(E1000_SWSM_SMBI | E1000_SWSM_SWESMBI); 1018 } else 1019 swsm &= ~(E1000_SWSM_SWESMBI); 1020 E1000_WRITE_REG(hw, SWSM, swsm); 1021 #endif 1022 } 1023 1024 /*************************************************************************** 1025 * 1026 * Using the combination of SMBI and SWESMBI semaphore bits when resetting 1027 * adapter or Eeprom access. 1028 * 1029 * hw: Struct containing variables accessed by shared code 1030 * 1031 * returns: - E1000_ERR_EEPROM if fail to access EEPROM. 1032 * E1000_SUCCESS at any other case. 1033 * 1034 ***************************************************************************/ 1035 static int32_t 1036 e1000_get_hw_eeprom_semaphore(struct e1000_hw *hw) 1037 { 1038 #ifndef CONFIG_E1000_NO_NVM 1039 int32_t timeout; 1040 uint32_t swsm; 1041 1042 DEBUGFUNC(); 1043 1044 if (!hw->eeprom_semaphore_present) 1045 return E1000_SUCCESS; 1046 1047 if (hw->mac_type == e1000_80003es2lan) { 1048 /* Get the SW semaphore. */ 1049 if (e1000_get_software_semaphore(hw) != E1000_SUCCESS) 1050 return -E1000_ERR_EEPROM; 1051 } 1052 1053 /* Get the FW semaphore. */ 1054 timeout = hw->eeprom.word_size + 1; 1055 while (timeout) { 1056 swsm = E1000_READ_REG(hw, SWSM); 1057 swsm |= E1000_SWSM_SWESMBI; 1058 E1000_WRITE_REG(hw, SWSM, swsm); 1059 /* if we managed to set the bit we got the semaphore. */ 1060 swsm = E1000_READ_REG(hw, SWSM); 1061 if (swsm & E1000_SWSM_SWESMBI) 1062 break; 1063 1064 udelay(50); 1065 timeout--; 1066 } 1067 1068 if (!timeout) { 1069 /* Release semaphores */ 1070 e1000_put_hw_eeprom_semaphore(hw); 1071 DEBUGOUT("Driver can't access the Eeprom - " 1072 "SWESMBI bit is set.\n"); 1073 return -E1000_ERR_EEPROM; 1074 } 1075 #endif 1076 return E1000_SUCCESS; 1077 } 1078 1079 /* Take ownership of the PHY */ 1080 static int32_t 1081 e1000_swfw_sync_acquire(struct e1000_hw *hw, uint16_t mask) 1082 { 1083 uint32_t swfw_sync = 0; 1084 uint32_t swmask = mask; 1085 uint32_t fwmask = mask << 16; 1086 int32_t timeout = 200; 1087 1088 DEBUGFUNC(); 1089 while (timeout) { 1090 if (e1000_get_hw_eeprom_semaphore(hw)) 1091 return -E1000_ERR_SWFW_SYNC; 1092 1093 swfw_sync = E1000_READ_REG(hw, SW_FW_SYNC); 1094 if (!(swfw_sync & (fwmask | swmask))) 1095 break; 1096 1097 /* firmware currently using resource (fwmask) */ 1098 /* or other software thread currently using resource (swmask) */ 1099 e1000_put_hw_eeprom_semaphore(hw); 1100 mdelay(5); 1101 timeout--; 1102 } 1103 1104 if (!timeout) { 1105 DEBUGOUT("Driver can't access resource, SW_FW_SYNC timeout.\n"); 1106 return -E1000_ERR_SWFW_SYNC; 1107 } 1108 1109 swfw_sync |= swmask; 1110 E1000_WRITE_REG(hw, SW_FW_SYNC, swfw_sync); 1111 1112 e1000_put_hw_eeprom_semaphore(hw); 1113 return E1000_SUCCESS; 1114 } 1115 1116 static void e1000_swfw_sync_release(struct e1000_hw *hw, uint16_t mask) 1117 { 1118 uint32_t swfw_sync = 0; 1119 1120 DEBUGFUNC(); 1121 while (e1000_get_hw_eeprom_semaphore(hw)) 1122 ; /* Empty */ 1123 1124 swfw_sync = E1000_READ_REG(hw, SW_FW_SYNC); 1125 swfw_sync &= ~mask; 1126 E1000_WRITE_REG(hw, SW_FW_SYNC, swfw_sync); 1127 1128 e1000_put_hw_eeprom_semaphore(hw); 1129 } 1130 1131 static bool e1000_is_second_port(struct e1000_hw *hw) 1132 { 1133 switch (hw->mac_type) { 1134 case e1000_80003es2lan: 1135 case e1000_82546: 1136 case e1000_82571: 1137 if (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1) 1138 return true; 1139 /* Fallthrough */ 1140 default: 1141 return false; 1142 } 1143 } 1144 1145 #ifndef CONFIG_E1000_NO_NVM 1146 /****************************************************************************** 1147 * Reads the adapter's MAC address from the EEPROM and inverts the LSB for the 1148 * second function of dual function devices 1149 * 1150 * nic - Struct containing variables accessed by shared code 1151 *****************************************************************************/ 1152 static int 1153 e1000_read_mac_addr(struct e1000_hw *hw, unsigned char enetaddr[6]) 1154 { 1155 uint16_t offset; 1156 uint16_t eeprom_data; 1157 uint32_t reg_data = 0; 1158 int i; 1159 1160 DEBUGFUNC(); 1161 1162 for (i = 0; i < NODE_ADDRESS_SIZE; i += 2) { 1163 offset = i >> 1; 1164 if (hw->mac_type == e1000_igb) { 1165 /* i210 preloads MAC address into RAL/RAH registers */ 1166 if (offset == 0) 1167 reg_data = E1000_READ_REG_ARRAY(hw, RA, 0); 1168 else if (offset == 1) 1169 reg_data >>= 16; 1170 else if (offset == 2) 1171 reg_data = E1000_READ_REG_ARRAY(hw, RA, 1); 1172 eeprom_data = reg_data & 0xffff; 1173 } else if (e1000_read_eeprom(hw, offset, 1, &eeprom_data) < 0) { 1174 DEBUGOUT("EEPROM Read Error\n"); 1175 return -E1000_ERR_EEPROM; 1176 } 1177 enetaddr[i] = eeprom_data & 0xff; 1178 enetaddr[i + 1] = (eeprom_data >> 8) & 0xff; 1179 } 1180 1181 /* Invert the last bit if this is the second device */ 1182 if (e1000_is_second_port(hw)) 1183 enetaddr[5] ^= 1; 1184 1185 return 0; 1186 } 1187 #endif 1188 1189 /****************************************************************************** 1190 * Initializes receive address filters. 1191 * 1192 * hw - Struct containing variables accessed by shared code 1193 * 1194 * Places the MAC address in receive address register 0 and clears the rest 1195 * of the receive addresss registers. Clears the multicast table. Assumes 1196 * the receiver is in reset when the routine is called. 1197 *****************************************************************************/ 1198 static void 1199 e1000_init_rx_addrs(struct e1000_hw *hw, unsigned char enetaddr[6]) 1200 { 1201 uint32_t i; 1202 uint32_t addr_low; 1203 uint32_t addr_high; 1204 1205 DEBUGFUNC(); 1206 1207 /* Setup the receive address. */ 1208 DEBUGOUT("Programming MAC Address into RAR[0]\n"); 1209 addr_low = (enetaddr[0] | 1210 (enetaddr[1] << 8) | 1211 (enetaddr[2] << 16) | (enetaddr[3] << 24)); 1212 1213 addr_high = (enetaddr[4] | (enetaddr[5] << 8) | E1000_RAH_AV); 1214 1215 E1000_WRITE_REG_ARRAY(hw, RA, 0, addr_low); 1216 E1000_WRITE_REG_ARRAY(hw, RA, 1, addr_high); 1217 1218 /* Zero out the other 15 receive addresses. */ 1219 DEBUGOUT("Clearing RAR[1-15]\n"); 1220 for (i = 1; i < E1000_RAR_ENTRIES; i++) { 1221 E1000_WRITE_REG_ARRAY(hw, RA, (i << 1), 0); 1222 E1000_WRITE_REG_ARRAY(hw, RA, ((i << 1) + 1), 0); 1223 } 1224 } 1225 1226 /****************************************************************************** 1227 * Clears the VLAN filer table 1228 * 1229 * hw - Struct containing variables accessed by shared code 1230 *****************************************************************************/ 1231 static void 1232 e1000_clear_vfta(struct e1000_hw *hw) 1233 { 1234 uint32_t offset; 1235 1236 for (offset = 0; offset < E1000_VLAN_FILTER_TBL_SIZE; offset++) 1237 E1000_WRITE_REG_ARRAY(hw, VFTA, offset, 0); 1238 } 1239 1240 /****************************************************************************** 1241 * Set the mac type member in the hw struct. 1242 * 1243 * hw - Struct containing variables accessed by shared code 1244 *****************************************************************************/ 1245 int32_t 1246 e1000_set_mac_type(struct e1000_hw *hw) 1247 { 1248 DEBUGFUNC(); 1249 1250 switch (hw->device_id) { 1251 case E1000_DEV_ID_82542: 1252 switch (hw->revision_id) { 1253 case E1000_82542_2_0_REV_ID: 1254 hw->mac_type = e1000_82542_rev2_0; 1255 break; 1256 case E1000_82542_2_1_REV_ID: 1257 hw->mac_type = e1000_82542_rev2_1; 1258 break; 1259 default: 1260 /* Invalid 82542 revision ID */ 1261 return -E1000_ERR_MAC_TYPE; 1262 } 1263 break; 1264 case E1000_DEV_ID_82543GC_FIBER: 1265 case E1000_DEV_ID_82543GC_COPPER: 1266 hw->mac_type = e1000_82543; 1267 break; 1268 case E1000_DEV_ID_82544EI_COPPER: 1269 case E1000_DEV_ID_82544EI_FIBER: 1270 case E1000_DEV_ID_82544GC_COPPER: 1271 case E1000_DEV_ID_82544GC_LOM: 1272 hw->mac_type = e1000_82544; 1273 break; 1274 case E1000_DEV_ID_82540EM: 1275 case E1000_DEV_ID_82540EM_LOM: 1276 case E1000_DEV_ID_82540EP: 1277 case E1000_DEV_ID_82540EP_LOM: 1278 case E1000_DEV_ID_82540EP_LP: 1279 hw->mac_type = e1000_82540; 1280 break; 1281 case E1000_DEV_ID_82545EM_COPPER: 1282 case E1000_DEV_ID_82545EM_FIBER: 1283 hw->mac_type = e1000_82545; 1284 break; 1285 case E1000_DEV_ID_82545GM_COPPER: 1286 case E1000_DEV_ID_82545GM_FIBER: 1287 case E1000_DEV_ID_82545GM_SERDES: 1288 hw->mac_type = e1000_82545_rev_3; 1289 break; 1290 case E1000_DEV_ID_82546EB_COPPER: 1291 case E1000_DEV_ID_82546EB_FIBER: 1292 case E1000_DEV_ID_82546EB_QUAD_COPPER: 1293 hw->mac_type = e1000_82546; 1294 break; 1295 case E1000_DEV_ID_82546GB_COPPER: 1296 case E1000_DEV_ID_82546GB_FIBER: 1297 case E1000_DEV_ID_82546GB_SERDES: 1298 case E1000_DEV_ID_82546GB_PCIE: 1299 case E1000_DEV_ID_82546GB_QUAD_COPPER: 1300 case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3: 1301 hw->mac_type = e1000_82546_rev_3; 1302 break; 1303 case E1000_DEV_ID_82541EI: 1304 case E1000_DEV_ID_82541EI_MOBILE: 1305 case E1000_DEV_ID_82541ER_LOM: 1306 hw->mac_type = e1000_82541; 1307 break; 1308 case E1000_DEV_ID_82541ER: 1309 case E1000_DEV_ID_82541GI: 1310 case E1000_DEV_ID_82541GI_LF: 1311 case E1000_DEV_ID_82541GI_MOBILE: 1312 hw->mac_type = e1000_82541_rev_2; 1313 break; 1314 case E1000_DEV_ID_82547EI: 1315 case E1000_DEV_ID_82547EI_MOBILE: 1316 hw->mac_type = e1000_82547; 1317 break; 1318 case E1000_DEV_ID_82547GI: 1319 hw->mac_type = e1000_82547_rev_2; 1320 break; 1321 case E1000_DEV_ID_82571EB_COPPER: 1322 case E1000_DEV_ID_82571EB_FIBER: 1323 case E1000_DEV_ID_82571EB_SERDES: 1324 case E1000_DEV_ID_82571EB_SERDES_DUAL: 1325 case E1000_DEV_ID_82571EB_SERDES_QUAD: 1326 case E1000_DEV_ID_82571EB_QUAD_COPPER: 1327 case E1000_DEV_ID_82571PT_QUAD_COPPER: 1328 case E1000_DEV_ID_82571EB_QUAD_FIBER: 1329 case E1000_DEV_ID_82571EB_QUAD_COPPER_LOWPROFILE: 1330 hw->mac_type = e1000_82571; 1331 break; 1332 case E1000_DEV_ID_82572EI_COPPER: 1333 case E1000_DEV_ID_82572EI_FIBER: 1334 case E1000_DEV_ID_82572EI_SERDES: 1335 case E1000_DEV_ID_82572EI: 1336 hw->mac_type = e1000_82572; 1337 break; 1338 case E1000_DEV_ID_82573E: 1339 case E1000_DEV_ID_82573E_IAMT: 1340 case E1000_DEV_ID_82573L: 1341 hw->mac_type = e1000_82573; 1342 break; 1343 case E1000_DEV_ID_82574L: 1344 hw->mac_type = e1000_82574; 1345 break; 1346 case E1000_DEV_ID_80003ES2LAN_COPPER_SPT: 1347 case E1000_DEV_ID_80003ES2LAN_SERDES_SPT: 1348 case E1000_DEV_ID_80003ES2LAN_COPPER_DPT: 1349 case E1000_DEV_ID_80003ES2LAN_SERDES_DPT: 1350 hw->mac_type = e1000_80003es2lan; 1351 break; 1352 case E1000_DEV_ID_ICH8_IGP_M_AMT: 1353 case E1000_DEV_ID_ICH8_IGP_AMT: 1354 case E1000_DEV_ID_ICH8_IGP_C: 1355 case E1000_DEV_ID_ICH8_IFE: 1356 case E1000_DEV_ID_ICH8_IFE_GT: 1357 case E1000_DEV_ID_ICH8_IFE_G: 1358 case E1000_DEV_ID_ICH8_IGP_M: 1359 hw->mac_type = e1000_ich8lan; 1360 break; 1361 case PCI_DEVICE_ID_INTEL_I210_UNPROGRAMMED: 1362 case PCI_DEVICE_ID_INTEL_I211_UNPROGRAMMED: 1363 case PCI_DEVICE_ID_INTEL_I210_COPPER: 1364 case PCI_DEVICE_ID_INTEL_I211_COPPER: 1365 case PCI_DEVICE_ID_INTEL_I210_COPPER_FLASHLESS: 1366 case PCI_DEVICE_ID_INTEL_I210_SERDES: 1367 case PCI_DEVICE_ID_INTEL_I210_SERDES_FLASHLESS: 1368 case PCI_DEVICE_ID_INTEL_I210_1000BASEKX: 1369 hw->mac_type = e1000_igb; 1370 break; 1371 default: 1372 /* Should never have loaded on this device */ 1373 return -E1000_ERR_MAC_TYPE; 1374 } 1375 return E1000_SUCCESS; 1376 } 1377 1378 /****************************************************************************** 1379 * Reset the transmit and receive units; mask and clear all interrupts. 1380 * 1381 * hw - Struct containing variables accessed by shared code 1382 *****************************************************************************/ 1383 void 1384 e1000_reset_hw(struct e1000_hw *hw) 1385 { 1386 uint32_t ctrl; 1387 uint32_t ctrl_ext; 1388 uint32_t manc; 1389 uint32_t pba = 0; 1390 uint32_t reg; 1391 1392 DEBUGFUNC(); 1393 1394 /* get the correct pba value for both PCI and PCIe*/ 1395 if (hw->mac_type < e1000_82571) 1396 pba = E1000_DEFAULT_PCI_PBA; 1397 else 1398 pba = E1000_DEFAULT_PCIE_PBA; 1399 1400 /* For 82542 (rev 2.0), disable MWI before issuing a device reset */ 1401 if (hw->mac_type == e1000_82542_rev2_0) { 1402 DEBUGOUT("Disabling MWI on 82542 rev 2.0\n"); 1403 #ifdef CONFIG_DM_ETH 1404 dm_pci_write_config16(hw->pdev, PCI_COMMAND, 1405 hw->pci_cmd_word & ~PCI_COMMAND_INVALIDATE); 1406 #else 1407 pci_write_config_word(hw->pdev, PCI_COMMAND, 1408 hw->pci_cmd_word & ~PCI_COMMAND_INVALIDATE); 1409 #endif 1410 } 1411 1412 /* Clear interrupt mask to stop board from generating interrupts */ 1413 DEBUGOUT("Masking off all interrupts\n"); 1414 if (hw->mac_type == e1000_igb) 1415 E1000_WRITE_REG(hw, I210_IAM, 0); 1416 E1000_WRITE_REG(hw, IMC, 0xffffffff); 1417 1418 /* Disable the Transmit and Receive units. Then delay to allow 1419 * any pending transactions to complete before we hit the MAC with 1420 * the global reset. 1421 */ 1422 E1000_WRITE_REG(hw, RCTL, 0); 1423 E1000_WRITE_REG(hw, TCTL, E1000_TCTL_PSP); 1424 E1000_WRITE_FLUSH(hw); 1425 1426 /* The tbi_compatibility_on Flag must be cleared when Rctl is cleared. */ 1427 hw->tbi_compatibility_on = false; 1428 1429 /* Delay to allow any outstanding PCI transactions to complete before 1430 * resetting the device 1431 */ 1432 mdelay(10); 1433 1434 /* Issue a global reset to the MAC. This will reset the chip's 1435 * transmit, receive, DMA, and link units. It will not effect 1436 * the current PCI configuration. The global reset bit is self- 1437 * clearing, and should clear within a microsecond. 1438 */ 1439 DEBUGOUT("Issuing a global reset to MAC\n"); 1440 ctrl = E1000_READ_REG(hw, CTRL); 1441 1442 E1000_WRITE_REG(hw, CTRL, (ctrl | E1000_CTRL_RST)); 1443 1444 /* Force a reload from the EEPROM if necessary */ 1445 if (hw->mac_type == e1000_igb) { 1446 mdelay(20); 1447 reg = E1000_READ_REG(hw, STATUS); 1448 if (reg & E1000_STATUS_PF_RST_DONE) 1449 DEBUGOUT("PF OK\n"); 1450 reg = E1000_READ_REG(hw, I210_EECD); 1451 if (reg & E1000_EECD_AUTO_RD) 1452 DEBUGOUT("EEC OK\n"); 1453 } else if (hw->mac_type < e1000_82540) { 1454 /* Wait for reset to complete */ 1455 udelay(10); 1456 ctrl_ext = E1000_READ_REG(hw, CTRL_EXT); 1457 ctrl_ext |= E1000_CTRL_EXT_EE_RST; 1458 E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext); 1459 E1000_WRITE_FLUSH(hw); 1460 /* Wait for EEPROM reload */ 1461 mdelay(2); 1462 } else { 1463 /* Wait for EEPROM reload (it happens automatically) */ 1464 mdelay(4); 1465 /* Dissable HW ARPs on ASF enabled adapters */ 1466 manc = E1000_READ_REG(hw, MANC); 1467 manc &= ~(E1000_MANC_ARP_EN); 1468 E1000_WRITE_REG(hw, MANC, manc); 1469 } 1470 1471 /* Clear interrupt mask to stop board from generating interrupts */ 1472 DEBUGOUT("Masking off all interrupts\n"); 1473 if (hw->mac_type == e1000_igb) 1474 E1000_WRITE_REG(hw, I210_IAM, 0); 1475 E1000_WRITE_REG(hw, IMC, 0xffffffff); 1476 1477 /* Clear any pending interrupt events. */ 1478 E1000_READ_REG(hw, ICR); 1479 1480 /* If MWI was previously enabled, reenable it. */ 1481 if (hw->mac_type == e1000_82542_rev2_0) { 1482 #ifdef CONFIG_DM_ETH 1483 dm_pci_write_config16(hw->pdev, PCI_COMMAND, hw->pci_cmd_word); 1484 #else 1485 pci_write_config_word(hw->pdev, PCI_COMMAND, hw->pci_cmd_word); 1486 #endif 1487 } 1488 if (hw->mac_type != e1000_igb) 1489 E1000_WRITE_REG(hw, PBA, pba); 1490 } 1491 1492 /****************************************************************************** 1493 * 1494 * Initialize a number of hardware-dependent bits 1495 * 1496 * hw: Struct containing variables accessed by shared code 1497 * 1498 * This function contains hardware limitation workarounds for PCI-E adapters 1499 * 1500 *****************************************************************************/ 1501 static void 1502 e1000_initialize_hardware_bits(struct e1000_hw *hw) 1503 { 1504 if ((hw->mac_type >= e1000_82571) && 1505 (!hw->initialize_hw_bits_disable)) { 1506 /* Settings common to all PCI-express silicon */ 1507 uint32_t reg_ctrl, reg_ctrl_ext; 1508 uint32_t reg_tarc0, reg_tarc1; 1509 uint32_t reg_tctl; 1510 uint32_t reg_txdctl, reg_txdctl1; 1511 1512 /* link autonegotiation/sync workarounds */ 1513 reg_tarc0 = E1000_READ_REG(hw, TARC0); 1514 reg_tarc0 &= ~((1 << 30)|(1 << 29)|(1 << 28)|(1 << 27)); 1515 1516 /* Enable not-done TX descriptor counting */ 1517 reg_txdctl = E1000_READ_REG(hw, TXDCTL); 1518 reg_txdctl |= E1000_TXDCTL_COUNT_DESC; 1519 E1000_WRITE_REG(hw, TXDCTL, reg_txdctl); 1520 1521 reg_txdctl1 = E1000_READ_REG(hw, TXDCTL1); 1522 reg_txdctl1 |= E1000_TXDCTL_COUNT_DESC; 1523 E1000_WRITE_REG(hw, TXDCTL1, reg_txdctl1); 1524 1525 /* IGB is cool */ 1526 if (hw->mac_type == e1000_igb) 1527 return; 1528 1529 switch (hw->mac_type) { 1530 case e1000_82571: 1531 case e1000_82572: 1532 /* Clear PHY TX compatible mode bits */ 1533 reg_tarc1 = E1000_READ_REG(hw, TARC1); 1534 reg_tarc1 &= ~((1 << 30)|(1 << 29)); 1535 1536 /* link autonegotiation/sync workarounds */ 1537 reg_tarc0 |= ((1 << 26)|(1 << 25)|(1 << 24)|(1 << 23)); 1538 1539 /* TX ring control fixes */ 1540 reg_tarc1 |= ((1 << 26)|(1 << 25)|(1 << 24)); 1541 1542 /* Multiple read bit is reversed polarity */ 1543 reg_tctl = E1000_READ_REG(hw, TCTL); 1544 if (reg_tctl & E1000_TCTL_MULR) 1545 reg_tarc1 &= ~(1 << 28); 1546 else 1547 reg_tarc1 |= (1 << 28); 1548 1549 E1000_WRITE_REG(hw, TARC1, reg_tarc1); 1550 break; 1551 case e1000_82573: 1552 case e1000_82574: 1553 reg_ctrl_ext = E1000_READ_REG(hw, CTRL_EXT); 1554 reg_ctrl_ext &= ~(1 << 23); 1555 reg_ctrl_ext |= (1 << 22); 1556 1557 /* TX byte count fix */ 1558 reg_ctrl = E1000_READ_REG(hw, CTRL); 1559 reg_ctrl &= ~(1 << 29); 1560 1561 E1000_WRITE_REG(hw, CTRL_EXT, reg_ctrl_ext); 1562 E1000_WRITE_REG(hw, CTRL, reg_ctrl); 1563 break; 1564 case e1000_80003es2lan: 1565 /* improve small packet performace for fiber/serdes */ 1566 if ((hw->media_type == e1000_media_type_fiber) 1567 || (hw->media_type == 1568 e1000_media_type_internal_serdes)) { 1569 reg_tarc0 &= ~(1 << 20); 1570 } 1571 1572 /* Multiple read bit is reversed polarity */ 1573 reg_tctl = E1000_READ_REG(hw, TCTL); 1574 reg_tarc1 = E1000_READ_REG(hw, TARC1); 1575 if (reg_tctl & E1000_TCTL_MULR) 1576 reg_tarc1 &= ~(1 << 28); 1577 else 1578 reg_tarc1 |= (1 << 28); 1579 1580 E1000_WRITE_REG(hw, TARC1, reg_tarc1); 1581 break; 1582 case e1000_ich8lan: 1583 /* Reduce concurrent DMA requests to 3 from 4 */ 1584 if ((hw->revision_id < 3) || 1585 ((hw->device_id != E1000_DEV_ID_ICH8_IGP_M_AMT) && 1586 (hw->device_id != E1000_DEV_ID_ICH8_IGP_M))) 1587 reg_tarc0 |= ((1 << 29)|(1 << 28)); 1588 1589 reg_ctrl_ext = E1000_READ_REG(hw, CTRL_EXT); 1590 reg_ctrl_ext |= (1 << 22); 1591 E1000_WRITE_REG(hw, CTRL_EXT, reg_ctrl_ext); 1592 1593 /* workaround TX hang with TSO=on */ 1594 reg_tarc0 |= ((1 << 27)|(1 << 26)|(1 << 24)|(1 << 23)); 1595 1596 /* Multiple read bit is reversed polarity */ 1597 reg_tctl = E1000_READ_REG(hw, TCTL); 1598 reg_tarc1 = E1000_READ_REG(hw, TARC1); 1599 if (reg_tctl & E1000_TCTL_MULR) 1600 reg_tarc1 &= ~(1 << 28); 1601 else 1602 reg_tarc1 |= (1 << 28); 1603 1604 /* workaround TX hang with TSO=on */ 1605 reg_tarc1 |= ((1 << 30)|(1 << 26)|(1 << 24)); 1606 1607 E1000_WRITE_REG(hw, TARC1, reg_tarc1); 1608 break; 1609 default: 1610 break; 1611 } 1612 1613 E1000_WRITE_REG(hw, TARC0, reg_tarc0); 1614 } 1615 } 1616 1617 /****************************************************************************** 1618 * Performs basic configuration of the adapter. 1619 * 1620 * hw - Struct containing variables accessed by shared code 1621 * 1622 * Assumes that the controller has previously been reset and is in a 1623 * post-reset uninitialized state. Initializes the receive address registers, 1624 * multicast table, and VLAN filter table. Calls routines to setup link 1625 * configuration and flow control settings. Clears all on-chip counters. Leaves 1626 * the transmit and receive units disabled and uninitialized. 1627 *****************************************************************************/ 1628 static int 1629 e1000_init_hw(struct e1000_hw *hw, unsigned char enetaddr[6]) 1630 { 1631 uint32_t ctrl; 1632 uint32_t i; 1633 int32_t ret_val; 1634 uint16_t pcix_cmd_word; 1635 uint16_t pcix_stat_hi_word; 1636 uint16_t cmd_mmrbc; 1637 uint16_t stat_mmrbc; 1638 uint32_t mta_size; 1639 uint32_t reg_data; 1640 uint32_t ctrl_ext; 1641 DEBUGFUNC(); 1642 /* force full DMA clock frequency for 10/100 on ICH8 A0-B0 */ 1643 if ((hw->mac_type == e1000_ich8lan) && 1644 ((hw->revision_id < 3) || 1645 ((hw->device_id != E1000_DEV_ID_ICH8_IGP_M_AMT) && 1646 (hw->device_id != E1000_DEV_ID_ICH8_IGP_M)))) { 1647 reg_data = E1000_READ_REG(hw, STATUS); 1648 reg_data &= ~0x80000000; 1649 E1000_WRITE_REG(hw, STATUS, reg_data); 1650 } 1651 /* Do not need initialize Identification LED */ 1652 1653 /* Set the media type and TBI compatibility */ 1654 e1000_set_media_type(hw); 1655 1656 /* Must be called after e1000_set_media_type 1657 * because media_type is used */ 1658 e1000_initialize_hardware_bits(hw); 1659 1660 /* Disabling VLAN filtering. */ 1661 DEBUGOUT("Initializing the IEEE VLAN\n"); 1662 /* VET hardcoded to standard value and VFTA removed in ICH8 LAN */ 1663 if (hw->mac_type != e1000_ich8lan) { 1664 if (hw->mac_type < e1000_82545_rev_3) 1665 E1000_WRITE_REG(hw, VET, 0); 1666 e1000_clear_vfta(hw); 1667 } 1668 1669 /* For 82542 (rev 2.0), disable MWI and put the receiver into reset */ 1670 if (hw->mac_type == e1000_82542_rev2_0) { 1671 DEBUGOUT("Disabling MWI on 82542 rev 2.0\n"); 1672 #ifdef CONFIG_DM_ETH 1673 dm_pci_write_config16(hw->pdev, PCI_COMMAND, 1674 hw-> 1675 pci_cmd_word & ~PCI_COMMAND_INVALIDATE); 1676 #else 1677 pci_write_config_word(hw->pdev, PCI_COMMAND, 1678 hw-> 1679 pci_cmd_word & ~PCI_COMMAND_INVALIDATE); 1680 #endif 1681 E1000_WRITE_REG(hw, RCTL, E1000_RCTL_RST); 1682 E1000_WRITE_FLUSH(hw); 1683 mdelay(5); 1684 } 1685 1686 /* Setup the receive address. This involves initializing all of the Receive 1687 * Address Registers (RARs 0 - 15). 1688 */ 1689 e1000_init_rx_addrs(hw, enetaddr); 1690 1691 /* For 82542 (rev 2.0), take the receiver out of reset and enable MWI */ 1692 if (hw->mac_type == e1000_82542_rev2_0) { 1693 E1000_WRITE_REG(hw, RCTL, 0); 1694 E1000_WRITE_FLUSH(hw); 1695 mdelay(1); 1696 #ifdef CONFIG_DM_ETH 1697 dm_pci_write_config16(hw->pdev, PCI_COMMAND, hw->pci_cmd_word); 1698 #else 1699 pci_write_config_word(hw->pdev, PCI_COMMAND, hw->pci_cmd_word); 1700 #endif 1701 } 1702 1703 /* Zero out the Multicast HASH table */ 1704 DEBUGOUT("Zeroing the MTA\n"); 1705 mta_size = E1000_MC_TBL_SIZE; 1706 if (hw->mac_type == e1000_ich8lan) 1707 mta_size = E1000_MC_TBL_SIZE_ICH8LAN; 1708 for (i = 0; i < mta_size; i++) { 1709 E1000_WRITE_REG_ARRAY(hw, MTA, i, 0); 1710 /* use write flush to prevent Memory Write Block (MWB) from 1711 * occuring when accessing our register space */ 1712 E1000_WRITE_FLUSH(hw); 1713 } 1714 1715 switch (hw->mac_type) { 1716 case e1000_82545_rev_3: 1717 case e1000_82546_rev_3: 1718 case e1000_igb: 1719 break; 1720 default: 1721 /* Workaround for PCI-X problem when BIOS sets MMRBC incorrectly. */ 1722 if (hw->bus_type == e1000_bus_type_pcix) { 1723 #ifdef CONFIG_DM_ETH 1724 dm_pci_read_config16(hw->pdev, PCIX_COMMAND_REGISTER, 1725 &pcix_cmd_word); 1726 dm_pci_read_config16(hw->pdev, PCIX_STATUS_REGISTER_HI, 1727 &pcix_stat_hi_word); 1728 #else 1729 pci_read_config_word(hw->pdev, PCIX_COMMAND_REGISTER, 1730 &pcix_cmd_word); 1731 pci_read_config_word(hw->pdev, PCIX_STATUS_REGISTER_HI, 1732 &pcix_stat_hi_word); 1733 #endif 1734 cmd_mmrbc = 1735 (pcix_cmd_word & PCIX_COMMAND_MMRBC_MASK) >> 1736 PCIX_COMMAND_MMRBC_SHIFT; 1737 stat_mmrbc = 1738 (pcix_stat_hi_word & PCIX_STATUS_HI_MMRBC_MASK) >> 1739 PCIX_STATUS_HI_MMRBC_SHIFT; 1740 if (stat_mmrbc == PCIX_STATUS_HI_MMRBC_4K) 1741 stat_mmrbc = PCIX_STATUS_HI_MMRBC_2K; 1742 if (cmd_mmrbc > stat_mmrbc) { 1743 pcix_cmd_word &= ~PCIX_COMMAND_MMRBC_MASK; 1744 pcix_cmd_word |= stat_mmrbc << PCIX_COMMAND_MMRBC_SHIFT; 1745 #ifdef CONFIG_DM_ETH 1746 dm_pci_write_config16(hw->pdev, PCIX_COMMAND_REGISTER, 1747 pcix_cmd_word); 1748 #else 1749 pci_write_config_word(hw->pdev, PCIX_COMMAND_REGISTER, 1750 pcix_cmd_word); 1751 #endif 1752 } 1753 } 1754 break; 1755 } 1756 1757 /* More time needed for PHY to initialize */ 1758 if (hw->mac_type == e1000_ich8lan) 1759 mdelay(15); 1760 if (hw->mac_type == e1000_igb) 1761 mdelay(15); 1762 1763 /* Call a subroutine to configure the link and setup flow control. */ 1764 ret_val = e1000_setup_link(hw); 1765 1766 /* Set the transmit descriptor write-back policy */ 1767 if (hw->mac_type > e1000_82544) { 1768 ctrl = E1000_READ_REG(hw, TXDCTL); 1769 ctrl = 1770 (ctrl & ~E1000_TXDCTL_WTHRESH) | 1771 E1000_TXDCTL_FULL_TX_DESC_WB; 1772 E1000_WRITE_REG(hw, TXDCTL, ctrl); 1773 } 1774 1775 /* Set the receive descriptor write back policy */ 1776 if (hw->mac_type >= e1000_82571) { 1777 ctrl = E1000_READ_REG(hw, RXDCTL); 1778 ctrl = 1779 (ctrl & ~E1000_RXDCTL_WTHRESH) | 1780 E1000_RXDCTL_FULL_RX_DESC_WB; 1781 E1000_WRITE_REG(hw, RXDCTL, ctrl); 1782 } 1783 1784 switch (hw->mac_type) { 1785 default: 1786 break; 1787 case e1000_80003es2lan: 1788 /* Enable retransmit on late collisions */ 1789 reg_data = E1000_READ_REG(hw, TCTL); 1790 reg_data |= E1000_TCTL_RTLC; 1791 E1000_WRITE_REG(hw, TCTL, reg_data); 1792 1793 /* Configure Gigabit Carry Extend Padding */ 1794 reg_data = E1000_READ_REG(hw, TCTL_EXT); 1795 reg_data &= ~E1000_TCTL_EXT_GCEX_MASK; 1796 reg_data |= DEFAULT_80003ES2LAN_TCTL_EXT_GCEX; 1797 E1000_WRITE_REG(hw, TCTL_EXT, reg_data); 1798 1799 /* Configure Transmit Inter-Packet Gap */ 1800 reg_data = E1000_READ_REG(hw, TIPG); 1801 reg_data &= ~E1000_TIPG_IPGT_MASK; 1802 reg_data |= DEFAULT_80003ES2LAN_TIPG_IPGT_1000; 1803 E1000_WRITE_REG(hw, TIPG, reg_data); 1804 1805 reg_data = E1000_READ_REG_ARRAY(hw, FFLT, 0x0001); 1806 reg_data &= ~0x00100000; 1807 E1000_WRITE_REG_ARRAY(hw, FFLT, 0x0001, reg_data); 1808 /* Fall through */ 1809 case e1000_82571: 1810 case e1000_82572: 1811 case e1000_ich8lan: 1812 ctrl = E1000_READ_REG(hw, TXDCTL1); 1813 ctrl = (ctrl & ~E1000_TXDCTL_WTHRESH) 1814 | E1000_TXDCTL_FULL_TX_DESC_WB; 1815 E1000_WRITE_REG(hw, TXDCTL1, ctrl); 1816 break; 1817 case e1000_82573: 1818 case e1000_82574: 1819 reg_data = E1000_READ_REG(hw, GCR); 1820 reg_data |= E1000_GCR_L1_ACT_WITHOUT_L0S_RX; 1821 E1000_WRITE_REG(hw, GCR, reg_data); 1822 case e1000_igb: 1823 break; 1824 } 1825 1826 if (hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER || 1827 hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3) { 1828 ctrl_ext = E1000_READ_REG(hw, CTRL_EXT); 1829 /* Relaxed ordering must be disabled to avoid a parity 1830 * error crash in a PCI slot. */ 1831 ctrl_ext |= E1000_CTRL_EXT_RO_DIS; 1832 E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext); 1833 } 1834 1835 return ret_val; 1836 } 1837 1838 /****************************************************************************** 1839 * Configures flow control and link settings. 1840 * 1841 * hw - Struct containing variables accessed by shared code 1842 * 1843 * Determines which flow control settings to use. Calls the apropriate media- 1844 * specific link configuration function. Configures the flow control settings. 1845 * Assuming the adapter has a valid link partner, a valid link should be 1846 * established. Assumes the hardware has previously been reset and the 1847 * transmitter and receiver are not enabled. 1848 *****************************************************************************/ 1849 static int 1850 e1000_setup_link(struct e1000_hw *hw) 1851 { 1852 int32_t ret_val; 1853 #ifndef CONFIG_E1000_NO_NVM 1854 uint32_t ctrl_ext; 1855 uint16_t eeprom_data; 1856 #endif 1857 1858 DEBUGFUNC(); 1859 1860 /* In the case of the phy reset being blocked, we already have a link. 1861 * We do not have to set it up again. */ 1862 if (e1000_check_phy_reset_block(hw)) 1863 return E1000_SUCCESS; 1864 1865 #ifndef CONFIG_E1000_NO_NVM 1866 /* Read and store word 0x0F of the EEPROM. This word contains bits 1867 * that determine the hardware's default PAUSE (flow control) mode, 1868 * a bit that determines whether the HW defaults to enabling or 1869 * disabling auto-negotiation, and the direction of the 1870 * SW defined pins. If there is no SW over-ride of the flow 1871 * control setting, then the variable hw->fc will 1872 * be initialized based on a value in the EEPROM. 1873 */ 1874 if (e1000_read_eeprom(hw, EEPROM_INIT_CONTROL2_REG, 1, 1875 &eeprom_data) < 0) { 1876 DEBUGOUT("EEPROM Read Error\n"); 1877 return -E1000_ERR_EEPROM; 1878 } 1879 #endif 1880 if (hw->fc == e1000_fc_default) { 1881 switch (hw->mac_type) { 1882 case e1000_ich8lan: 1883 case e1000_82573: 1884 case e1000_82574: 1885 case e1000_igb: 1886 hw->fc = e1000_fc_full; 1887 break; 1888 default: 1889 #ifndef CONFIG_E1000_NO_NVM 1890 ret_val = e1000_read_eeprom(hw, 1891 EEPROM_INIT_CONTROL2_REG, 1, &eeprom_data); 1892 if (ret_val) { 1893 DEBUGOUT("EEPROM Read Error\n"); 1894 return -E1000_ERR_EEPROM; 1895 } 1896 if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) == 0) 1897 hw->fc = e1000_fc_none; 1898 else if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) == 1899 EEPROM_WORD0F_ASM_DIR) 1900 hw->fc = e1000_fc_tx_pause; 1901 else 1902 #endif 1903 hw->fc = e1000_fc_full; 1904 break; 1905 } 1906 } 1907 1908 /* We want to save off the original Flow Control configuration just 1909 * in case we get disconnected and then reconnected into a different 1910 * hub or switch with different Flow Control capabilities. 1911 */ 1912 if (hw->mac_type == e1000_82542_rev2_0) 1913 hw->fc &= (~e1000_fc_tx_pause); 1914 1915 if ((hw->mac_type < e1000_82543) && (hw->report_tx_early == 1)) 1916 hw->fc &= (~e1000_fc_rx_pause); 1917 1918 hw->original_fc = hw->fc; 1919 1920 DEBUGOUT("After fix-ups FlowControl is now = %x\n", hw->fc); 1921 1922 #ifndef CONFIG_E1000_NO_NVM 1923 /* Take the 4 bits from EEPROM word 0x0F that determine the initial 1924 * polarity value for the SW controlled pins, and setup the 1925 * Extended Device Control reg with that info. 1926 * This is needed because one of the SW controlled pins is used for 1927 * signal detection. So this should be done before e1000_setup_pcs_link() 1928 * or e1000_phy_setup() is called. 1929 */ 1930 if (hw->mac_type == e1000_82543) { 1931 ctrl_ext = ((eeprom_data & EEPROM_WORD0F_SWPDIO_EXT) << 1932 SWDPIO__EXT_SHIFT); 1933 E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext); 1934 } 1935 #endif 1936 1937 /* Call the necessary subroutine to configure the link. */ 1938 ret_val = (hw->media_type == e1000_media_type_fiber) ? 1939 e1000_setup_fiber_link(hw) : e1000_setup_copper_link(hw); 1940 if (ret_val < 0) { 1941 return ret_val; 1942 } 1943 1944 /* Initialize the flow control address, type, and PAUSE timer 1945 * registers to their default values. This is done even if flow 1946 * control is disabled, because it does not hurt anything to 1947 * initialize these registers. 1948 */ 1949 DEBUGOUT("Initializing the Flow Control address, type" 1950 "and timer regs\n"); 1951 1952 /* FCAL/H and FCT are hardcoded to standard values in e1000_ich8lan. */ 1953 if (hw->mac_type != e1000_ich8lan) { 1954 E1000_WRITE_REG(hw, FCT, FLOW_CONTROL_TYPE); 1955 E1000_WRITE_REG(hw, FCAH, FLOW_CONTROL_ADDRESS_HIGH); 1956 E1000_WRITE_REG(hw, FCAL, FLOW_CONTROL_ADDRESS_LOW); 1957 } 1958 1959 E1000_WRITE_REG(hw, FCTTV, hw->fc_pause_time); 1960 1961 /* Set the flow control receive threshold registers. Normally, 1962 * these registers will be set to a default threshold that may be 1963 * adjusted later by the driver's runtime code. However, if the 1964 * ability to transmit pause frames in not enabled, then these 1965 * registers will be set to 0. 1966 */ 1967 if (!(hw->fc & e1000_fc_tx_pause)) { 1968 E1000_WRITE_REG(hw, FCRTL, 0); 1969 E1000_WRITE_REG(hw, FCRTH, 0); 1970 } else { 1971 /* We need to set up the Receive Threshold high and low water marks 1972 * as well as (optionally) enabling the transmission of XON frames. 1973 */ 1974 if (hw->fc_send_xon) { 1975 E1000_WRITE_REG(hw, FCRTL, 1976 (hw->fc_low_water | E1000_FCRTL_XONE)); 1977 E1000_WRITE_REG(hw, FCRTH, hw->fc_high_water); 1978 } else { 1979 E1000_WRITE_REG(hw, FCRTL, hw->fc_low_water); 1980 E1000_WRITE_REG(hw, FCRTH, hw->fc_high_water); 1981 } 1982 } 1983 return ret_val; 1984 } 1985 1986 /****************************************************************************** 1987 * Sets up link for a fiber based adapter 1988 * 1989 * hw - Struct containing variables accessed by shared code 1990 * 1991 * Manipulates Physical Coding Sublayer functions in order to configure 1992 * link. Assumes the hardware has been previously reset and the transmitter 1993 * and receiver are not enabled. 1994 *****************************************************************************/ 1995 static int 1996 e1000_setup_fiber_link(struct e1000_hw *hw) 1997 { 1998 uint32_t ctrl; 1999 uint32_t status; 2000 uint32_t txcw = 0; 2001 uint32_t i; 2002 uint32_t signal; 2003 int32_t ret_val; 2004 2005 DEBUGFUNC(); 2006 /* On adapters with a MAC newer that 82544, SW Defineable pin 1 will be 2007 * set when the optics detect a signal. On older adapters, it will be 2008 * cleared when there is a signal 2009 */ 2010 ctrl = E1000_READ_REG(hw, CTRL); 2011 if ((hw->mac_type > e1000_82544) && !(ctrl & E1000_CTRL_ILOS)) 2012 signal = E1000_CTRL_SWDPIN1; 2013 else 2014 signal = 0; 2015 2016 printf("signal for %s is %x (ctrl %08x)!!!!\n", hw->name, signal, 2017 ctrl); 2018 /* Take the link out of reset */ 2019 ctrl &= ~(E1000_CTRL_LRST); 2020 2021 e1000_config_collision_dist(hw); 2022 2023 /* Check for a software override of the flow control settings, and setup 2024 * the device accordingly. If auto-negotiation is enabled, then software 2025 * will have to set the "PAUSE" bits to the correct value in the Tranmsit 2026 * Config Word Register (TXCW) and re-start auto-negotiation. However, if 2027 * auto-negotiation is disabled, then software will have to manually 2028 * configure the two flow control enable bits in the CTRL register. 2029 * 2030 * The possible values of the "fc" parameter are: 2031 * 0: Flow control is completely disabled 2032 * 1: Rx flow control is enabled (we can receive pause frames, but 2033 * not send pause frames). 2034 * 2: Tx flow control is enabled (we can send pause frames but we do 2035 * not support receiving pause frames). 2036 * 3: Both Rx and TX flow control (symmetric) are enabled. 2037 */ 2038 switch (hw->fc) { 2039 case e1000_fc_none: 2040 /* Flow control is completely disabled by a software over-ride. */ 2041 txcw = (E1000_TXCW_ANE | E1000_TXCW_FD); 2042 break; 2043 case e1000_fc_rx_pause: 2044 /* RX Flow control is enabled and TX Flow control is disabled by a 2045 * software over-ride. Since there really isn't a way to advertise 2046 * that we are capable of RX Pause ONLY, we will advertise that we 2047 * support both symmetric and asymmetric RX PAUSE. Later, we will 2048 * disable the adapter's ability to send PAUSE frames. 2049 */ 2050 txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK); 2051 break; 2052 case e1000_fc_tx_pause: 2053 /* TX Flow control is enabled, and RX Flow control is disabled, by a 2054 * software over-ride. 2055 */ 2056 txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_ASM_DIR); 2057 break; 2058 case e1000_fc_full: 2059 /* Flow control (both RX and TX) is enabled by a software over-ride. */ 2060 txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK); 2061 break; 2062 default: 2063 DEBUGOUT("Flow control param set incorrectly\n"); 2064 return -E1000_ERR_CONFIG; 2065 break; 2066 } 2067 2068 /* Since auto-negotiation is enabled, take the link out of reset (the link 2069 * will be in reset, because we previously reset the chip). This will 2070 * restart auto-negotiation. If auto-neogtiation is successful then the 2071 * link-up status bit will be set and the flow control enable bits (RFCE 2072 * and TFCE) will be set according to their negotiated value. 2073 */ 2074 DEBUGOUT("Auto-negotiation enabled (%#x)\n", txcw); 2075 2076 E1000_WRITE_REG(hw, TXCW, txcw); 2077 E1000_WRITE_REG(hw, CTRL, ctrl); 2078 E1000_WRITE_FLUSH(hw); 2079 2080 hw->txcw = txcw; 2081 mdelay(1); 2082 2083 /* If we have a signal (the cable is plugged in) then poll for a "Link-Up" 2084 * indication in the Device Status Register. Time-out if a link isn't 2085 * seen in 500 milliseconds seconds (Auto-negotiation should complete in 2086 * less than 500 milliseconds even if the other end is doing it in SW). 2087 */ 2088 if ((E1000_READ_REG(hw, CTRL) & E1000_CTRL_SWDPIN1) == signal) { 2089 DEBUGOUT("Looking for Link\n"); 2090 for (i = 0; i < (LINK_UP_TIMEOUT / 10); i++) { 2091 mdelay(10); 2092 status = E1000_READ_REG(hw, STATUS); 2093 if (status & E1000_STATUS_LU) 2094 break; 2095 } 2096 if (i == (LINK_UP_TIMEOUT / 10)) { 2097 /* AutoNeg failed to achieve a link, so we'll call 2098 * e1000_check_for_link. This routine will force the link up if we 2099 * detect a signal. This will allow us to communicate with 2100 * non-autonegotiating link partners. 2101 */ 2102 DEBUGOUT("Never got a valid link from auto-neg!!!\n"); 2103 hw->autoneg_failed = 1; 2104 ret_val = e1000_check_for_link(hw); 2105 if (ret_val < 0) { 2106 DEBUGOUT("Error while checking for link\n"); 2107 return ret_val; 2108 } 2109 hw->autoneg_failed = 0; 2110 } else { 2111 hw->autoneg_failed = 0; 2112 DEBUGOUT("Valid Link Found\n"); 2113 } 2114 } else { 2115 DEBUGOUT("No Signal Detected\n"); 2116 return -E1000_ERR_NOLINK; 2117 } 2118 return 0; 2119 } 2120 2121 /****************************************************************************** 2122 * Make sure we have a valid PHY and change PHY mode before link setup. 2123 * 2124 * hw - Struct containing variables accessed by shared code 2125 ******************************************************************************/ 2126 static int32_t 2127 e1000_copper_link_preconfig(struct e1000_hw *hw) 2128 { 2129 uint32_t ctrl; 2130 int32_t ret_val; 2131 uint16_t phy_data; 2132 2133 DEBUGFUNC(); 2134 2135 ctrl = E1000_READ_REG(hw, CTRL); 2136 /* With 82543, we need to force speed and duplex on the MAC equal to what 2137 * the PHY speed and duplex configuration is. In addition, we need to 2138 * perform a hardware reset on the PHY to take it out of reset. 2139 */ 2140 if (hw->mac_type > e1000_82543) { 2141 ctrl |= E1000_CTRL_SLU; 2142 ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); 2143 E1000_WRITE_REG(hw, CTRL, ctrl); 2144 } else { 2145 ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX 2146 | E1000_CTRL_SLU); 2147 E1000_WRITE_REG(hw, CTRL, ctrl); 2148 ret_val = e1000_phy_hw_reset(hw); 2149 if (ret_val) 2150 return ret_val; 2151 } 2152 2153 /* Make sure we have a valid PHY */ 2154 ret_val = e1000_detect_gig_phy(hw); 2155 if (ret_val) { 2156 DEBUGOUT("Error, did not detect valid phy.\n"); 2157 return ret_val; 2158 } 2159 DEBUGOUT("Phy ID = %x\n", hw->phy_id); 2160 2161 /* Set PHY to class A mode (if necessary) */ 2162 ret_val = e1000_set_phy_mode(hw); 2163 if (ret_val) 2164 return ret_val; 2165 if ((hw->mac_type == e1000_82545_rev_3) || 2166 (hw->mac_type == e1000_82546_rev_3)) { 2167 ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, 2168 &phy_data); 2169 phy_data |= 0x00000008; 2170 ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, 2171 phy_data); 2172 } 2173 2174 if (hw->mac_type <= e1000_82543 || 2175 hw->mac_type == e1000_82541 || hw->mac_type == e1000_82547 || 2176 hw->mac_type == e1000_82541_rev_2 2177 || hw->mac_type == e1000_82547_rev_2) 2178 hw->phy_reset_disable = false; 2179 2180 return E1000_SUCCESS; 2181 } 2182 2183 /***************************************************************************** 2184 * 2185 * This function sets the lplu state according to the active flag. When 2186 * activating lplu this function also disables smart speed and vise versa. 2187 * lplu will not be activated unless the device autonegotiation advertisment 2188 * meets standards of either 10 or 10/100 or 10/100/1000 at all duplexes. 2189 * hw: Struct containing variables accessed by shared code 2190 * active - true to enable lplu false to disable lplu. 2191 * 2192 * returns: - E1000_ERR_PHY if fail to read/write the PHY 2193 * E1000_SUCCESS at any other case. 2194 * 2195 ****************************************************************************/ 2196 2197 static int32_t 2198 e1000_set_d3_lplu_state(struct e1000_hw *hw, bool active) 2199 { 2200 uint32_t phy_ctrl = 0; 2201 int32_t ret_val; 2202 uint16_t phy_data; 2203 DEBUGFUNC(); 2204 2205 if (hw->phy_type != e1000_phy_igp && hw->phy_type != e1000_phy_igp_2 2206 && hw->phy_type != e1000_phy_igp_3) 2207 return E1000_SUCCESS; 2208 2209 /* During driver activity LPLU should not be used or it will attain link 2210 * from the lowest speeds starting from 10Mbps. The capability is used 2211 * for Dx transitions and states */ 2212 if (hw->mac_type == e1000_82541_rev_2 2213 || hw->mac_type == e1000_82547_rev_2) { 2214 ret_val = e1000_read_phy_reg(hw, IGP01E1000_GMII_FIFO, 2215 &phy_data); 2216 if (ret_val) 2217 return ret_val; 2218 } else if (hw->mac_type == e1000_ich8lan) { 2219 /* MAC writes into PHY register based on the state transition 2220 * and start auto-negotiation. SW driver can overwrite the 2221 * settings in CSR PHY power control E1000_PHY_CTRL register. */ 2222 phy_ctrl = E1000_READ_REG(hw, PHY_CTRL); 2223 } else { 2224 ret_val = e1000_read_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, 2225 &phy_data); 2226 if (ret_val) 2227 return ret_val; 2228 } 2229 2230 if (!active) { 2231 if (hw->mac_type == e1000_82541_rev_2 || 2232 hw->mac_type == e1000_82547_rev_2) { 2233 phy_data &= ~IGP01E1000_GMII_FLEX_SPD; 2234 ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO, 2235 phy_data); 2236 if (ret_val) 2237 return ret_val; 2238 } else { 2239 if (hw->mac_type == e1000_ich8lan) { 2240 phy_ctrl &= ~E1000_PHY_CTRL_NOND0A_LPLU; 2241 E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl); 2242 } else { 2243 phy_data &= ~IGP02E1000_PM_D3_LPLU; 2244 ret_val = e1000_write_phy_reg(hw, 2245 IGP02E1000_PHY_POWER_MGMT, phy_data); 2246 if (ret_val) 2247 return ret_val; 2248 } 2249 } 2250 2251 /* LPLU and SmartSpeed are mutually exclusive. LPLU is used during 2252 * Dx states where the power conservation is most important. During 2253 * driver activity we should enable SmartSpeed, so performance is 2254 * maintained. */ 2255 if (hw->smart_speed == e1000_smart_speed_on) { 2256 ret_val = e1000_read_phy_reg(hw, 2257 IGP01E1000_PHY_PORT_CONFIG, &phy_data); 2258 if (ret_val) 2259 return ret_val; 2260 2261 phy_data |= IGP01E1000_PSCFR_SMART_SPEED; 2262 ret_val = e1000_write_phy_reg(hw, 2263 IGP01E1000_PHY_PORT_CONFIG, phy_data); 2264 if (ret_val) 2265 return ret_val; 2266 } else if (hw->smart_speed == e1000_smart_speed_off) { 2267 ret_val = e1000_read_phy_reg(hw, 2268 IGP01E1000_PHY_PORT_CONFIG, &phy_data); 2269 if (ret_val) 2270 return ret_val; 2271 2272 phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED; 2273 ret_val = e1000_write_phy_reg(hw, 2274 IGP01E1000_PHY_PORT_CONFIG, phy_data); 2275 if (ret_val) 2276 return ret_val; 2277 } 2278 2279 } else if ((hw->autoneg_advertised == AUTONEG_ADVERTISE_SPEED_DEFAULT) 2280 || (hw->autoneg_advertised == AUTONEG_ADVERTISE_10_ALL) || 2281 (hw->autoneg_advertised == AUTONEG_ADVERTISE_10_100_ALL)) { 2282 2283 if (hw->mac_type == e1000_82541_rev_2 || 2284 hw->mac_type == e1000_82547_rev_2) { 2285 phy_data |= IGP01E1000_GMII_FLEX_SPD; 2286 ret_val = e1000_write_phy_reg(hw, 2287 IGP01E1000_GMII_FIFO, phy_data); 2288 if (ret_val) 2289 return ret_val; 2290 } else { 2291 if (hw->mac_type == e1000_ich8lan) { 2292 phy_ctrl |= E1000_PHY_CTRL_NOND0A_LPLU; 2293 E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl); 2294 } else { 2295 phy_data |= IGP02E1000_PM_D3_LPLU; 2296 ret_val = e1000_write_phy_reg(hw, 2297 IGP02E1000_PHY_POWER_MGMT, phy_data); 2298 if (ret_val) 2299 return ret_val; 2300 } 2301 } 2302 2303 /* When LPLU is enabled we should disable SmartSpeed */ 2304 ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, 2305 &phy_data); 2306 if (ret_val) 2307 return ret_val; 2308 2309 phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED; 2310 ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, 2311 phy_data); 2312 if (ret_val) 2313 return ret_val; 2314 } 2315 return E1000_SUCCESS; 2316 } 2317 2318 /***************************************************************************** 2319 * 2320 * This function sets the lplu d0 state according to the active flag. When 2321 * activating lplu this function also disables smart speed and vise versa. 2322 * lplu will not be activated unless the device autonegotiation advertisment 2323 * meets standards of either 10 or 10/100 or 10/100/1000 at all duplexes. 2324 * hw: Struct containing variables accessed by shared code 2325 * active - true to enable lplu false to disable lplu. 2326 * 2327 * returns: - E1000_ERR_PHY if fail to read/write the PHY 2328 * E1000_SUCCESS at any other case. 2329 * 2330 ****************************************************************************/ 2331 2332 static int32_t 2333 e1000_set_d0_lplu_state(struct e1000_hw *hw, bool active) 2334 { 2335 uint32_t phy_ctrl = 0; 2336 int32_t ret_val; 2337 uint16_t phy_data; 2338 DEBUGFUNC(); 2339 2340 if (hw->mac_type <= e1000_82547_rev_2) 2341 return E1000_SUCCESS; 2342 2343 if (hw->mac_type == e1000_ich8lan) { 2344 phy_ctrl = E1000_READ_REG(hw, PHY_CTRL); 2345 } else if (hw->mac_type == e1000_igb) { 2346 phy_ctrl = E1000_READ_REG(hw, I210_PHY_CTRL); 2347 } else { 2348 ret_val = e1000_read_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, 2349 &phy_data); 2350 if (ret_val) 2351 return ret_val; 2352 } 2353 2354 if (!active) { 2355 if (hw->mac_type == e1000_ich8lan) { 2356 phy_ctrl &= ~E1000_PHY_CTRL_D0A_LPLU; 2357 E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl); 2358 } else if (hw->mac_type == e1000_igb) { 2359 phy_ctrl &= ~E1000_PHY_CTRL_D0A_LPLU; 2360 E1000_WRITE_REG(hw, I210_PHY_CTRL, phy_ctrl); 2361 } else { 2362 phy_data &= ~IGP02E1000_PM_D0_LPLU; 2363 ret_val = e1000_write_phy_reg(hw, 2364 IGP02E1000_PHY_POWER_MGMT, phy_data); 2365 if (ret_val) 2366 return ret_val; 2367 } 2368 2369 if (hw->mac_type == e1000_igb) 2370 return E1000_SUCCESS; 2371 2372 /* LPLU and SmartSpeed are mutually exclusive. LPLU is used during 2373 * Dx states where the power conservation is most important. During 2374 * driver activity we should enable SmartSpeed, so performance is 2375 * maintained. */ 2376 if (hw->smart_speed == e1000_smart_speed_on) { 2377 ret_val = e1000_read_phy_reg(hw, 2378 IGP01E1000_PHY_PORT_CONFIG, &phy_data); 2379 if (ret_val) 2380 return ret_val; 2381 2382 phy_data |= IGP01E1000_PSCFR_SMART_SPEED; 2383 ret_val = e1000_write_phy_reg(hw, 2384 IGP01E1000_PHY_PORT_CONFIG, phy_data); 2385 if (ret_val) 2386 return ret_val; 2387 } else if (hw->smart_speed == e1000_smart_speed_off) { 2388 ret_val = e1000_read_phy_reg(hw, 2389 IGP01E1000_PHY_PORT_CONFIG, &phy_data); 2390 if (ret_val) 2391 return ret_val; 2392 2393 phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED; 2394 ret_val = e1000_write_phy_reg(hw, 2395 IGP01E1000_PHY_PORT_CONFIG, phy_data); 2396 if (ret_val) 2397 return ret_val; 2398 } 2399 2400 2401 } else { 2402 2403 if (hw->mac_type == e1000_ich8lan) { 2404 phy_ctrl |= E1000_PHY_CTRL_D0A_LPLU; 2405 E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl); 2406 } else if (hw->mac_type == e1000_igb) { 2407 phy_ctrl |= E1000_PHY_CTRL_D0A_LPLU; 2408 E1000_WRITE_REG(hw, I210_PHY_CTRL, phy_ctrl); 2409 } else { 2410 phy_data |= IGP02E1000_PM_D0_LPLU; 2411 ret_val = e1000_write_phy_reg(hw, 2412 IGP02E1000_PHY_POWER_MGMT, phy_data); 2413 if (ret_val) 2414 return ret_val; 2415 } 2416 2417 if (hw->mac_type == e1000_igb) 2418 return E1000_SUCCESS; 2419 2420 /* When LPLU is enabled we should disable SmartSpeed */ 2421 ret_val = e1000_read_phy_reg(hw, 2422 IGP01E1000_PHY_PORT_CONFIG, &phy_data); 2423 if (ret_val) 2424 return ret_val; 2425 2426 phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED; 2427 ret_val = e1000_write_phy_reg(hw, 2428 IGP01E1000_PHY_PORT_CONFIG, phy_data); 2429 if (ret_val) 2430 return ret_val; 2431 2432 } 2433 return E1000_SUCCESS; 2434 } 2435 2436 /******************************************************************** 2437 * Copper link setup for e1000_phy_igp series. 2438 * 2439 * hw - Struct containing variables accessed by shared code 2440 *********************************************************************/ 2441 static int32_t 2442 e1000_copper_link_igp_setup(struct e1000_hw *hw) 2443 { 2444 uint32_t led_ctrl; 2445 int32_t ret_val; 2446 uint16_t phy_data; 2447 2448 DEBUGFUNC(); 2449 2450 if (hw->phy_reset_disable) 2451 return E1000_SUCCESS; 2452 2453 ret_val = e1000_phy_reset(hw); 2454 if (ret_val) { 2455 DEBUGOUT("Error Resetting the PHY\n"); 2456 return ret_val; 2457 } 2458 2459 /* Wait 15ms for MAC to configure PHY from eeprom settings */ 2460 mdelay(15); 2461 if (hw->mac_type != e1000_ich8lan) { 2462 /* Configure activity LED after PHY reset */ 2463 led_ctrl = E1000_READ_REG(hw, LEDCTL); 2464 led_ctrl &= IGP_ACTIVITY_LED_MASK; 2465 led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE); 2466 E1000_WRITE_REG(hw, LEDCTL, led_ctrl); 2467 } 2468 2469 /* The NVM settings will configure LPLU in D3 for IGP2 and IGP3 PHYs */ 2470 if (hw->phy_type == e1000_phy_igp) { 2471 /* disable lplu d3 during driver init */ 2472 ret_val = e1000_set_d3_lplu_state(hw, false); 2473 if (ret_val) { 2474 DEBUGOUT("Error Disabling LPLU D3\n"); 2475 return ret_val; 2476 } 2477 } 2478 2479 /* disable lplu d0 during driver init */ 2480 ret_val = e1000_set_d0_lplu_state(hw, false); 2481 if (ret_val) { 2482 DEBUGOUT("Error Disabling LPLU D0\n"); 2483 return ret_val; 2484 } 2485 /* Configure mdi-mdix settings */ 2486 ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, &phy_data); 2487 if (ret_val) 2488 return ret_val; 2489 2490 if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) { 2491 hw->dsp_config_state = e1000_dsp_config_disabled; 2492 /* Force MDI for earlier revs of the IGP PHY */ 2493 phy_data &= ~(IGP01E1000_PSCR_AUTO_MDIX 2494 | IGP01E1000_PSCR_FORCE_MDI_MDIX); 2495 hw->mdix = 1; 2496 2497 } else { 2498 hw->dsp_config_state = e1000_dsp_config_enabled; 2499 phy_data &= ~IGP01E1000_PSCR_AUTO_MDIX; 2500 2501 switch (hw->mdix) { 2502 case 1: 2503 phy_data &= ~IGP01E1000_PSCR_FORCE_MDI_MDIX; 2504 break; 2505 case 2: 2506 phy_data |= IGP01E1000_PSCR_FORCE_MDI_MDIX; 2507 break; 2508 case 0: 2509 default: 2510 phy_data |= IGP01E1000_PSCR_AUTO_MDIX; 2511 break; 2512 } 2513 } 2514 ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, phy_data); 2515 if (ret_val) 2516 return ret_val; 2517 2518 /* set auto-master slave resolution settings */ 2519 if (hw->autoneg) { 2520 e1000_ms_type phy_ms_setting = hw->master_slave; 2521 2522 if (hw->ffe_config_state == e1000_ffe_config_active) 2523 hw->ffe_config_state = e1000_ffe_config_enabled; 2524 2525 if (hw->dsp_config_state == e1000_dsp_config_activated) 2526 hw->dsp_config_state = e1000_dsp_config_enabled; 2527 2528 /* when autonegotiation advertisment is only 1000Mbps then we 2529 * should disable SmartSpeed and enable Auto MasterSlave 2530 * resolution as hardware default. */ 2531 if (hw->autoneg_advertised == ADVERTISE_1000_FULL) { 2532 /* Disable SmartSpeed */ 2533 ret_val = e1000_read_phy_reg(hw, 2534 IGP01E1000_PHY_PORT_CONFIG, &phy_data); 2535 if (ret_val) 2536 return ret_val; 2537 phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED; 2538 ret_val = e1000_write_phy_reg(hw, 2539 IGP01E1000_PHY_PORT_CONFIG, phy_data); 2540 if (ret_val) 2541 return ret_val; 2542 /* Set auto Master/Slave resolution process */ 2543 ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, 2544 &phy_data); 2545 if (ret_val) 2546 return ret_val; 2547 phy_data &= ~CR_1000T_MS_ENABLE; 2548 ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, 2549 phy_data); 2550 if (ret_val) 2551 return ret_val; 2552 } 2553 2554 ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &phy_data); 2555 if (ret_val) 2556 return ret_val; 2557 2558 /* load defaults for future use */ 2559 hw->original_master_slave = (phy_data & CR_1000T_MS_ENABLE) ? 2560 ((phy_data & CR_1000T_MS_VALUE) ? 2561 e1000_ms_force_master : 2562 e1000_ms_force_slave) : 2563 e1000_ms_auto; 2564 2565 switch (phy_ms_setting) { 2566 case e1000_ms_force_master: 2567 phy_data |= (CR_1000T_MS_ENABLE | CR_1000T_MS_VALUE); 2568 break; 2569 case e1000_ms_force_slave: 2570 phy_data |= CR_1000T_MS_ENABLE; 2571 phy_data &= ~(CR_1000T_MS_VALUE); 2572 break; 2573 case e1000_ms_auto: 2574 phy_data &= ~CR_1000T_MS_ENABLE; 2575 default: 2576 break; 2577 } 2578 ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, phy_data); 2579 if (ret_val) 2580 return ret_val; 2581 } 2582 2583 return E1000_SUCCESS; 2584 } 2585 2586 /***************************************************************************** 2587 * This function checks the mode of the firmware. 2588 * 2589 * returns - true when the mode is IAMT or false. 2590 ****************************************************************************/ 2591 bool 2592 e1000_check_mng_mode(struct e1000_hw *hw) 2593 { 2594 uint32_t fwsm; 2595 DEBUGFUNC(); 2596 2597 fwsm = E1000_READ_REG(hw, FWSM); 2598 2599 if (hw->mac_type == e1000_ich8lan) { 2600 if ((fwsm & E1000_FWSM_MODE_MASK) == 2601 (E1000_MNG_ICH_IAMT_MODE << E1000_FWSM_MODE_SHIFT)) 2602 return true; 2603 } else if ((fwsm & E1000_FWSM_MODE_MASK) == 2604 (E1000_MNG_IAMT_MODE << E1000_FWSM_MODE_SHIFT)) 2605 return true; 2606 2607 return false; 2608 } 2609 2610 static int32_t 2611 e1000_write_kmrn_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t data) 2612 { 2613 uint16_t swfw = E1000_SWFW_PHY0_SM; 2614 uint32_t reg_val; 2615 DEBUGFUNC(); 2616 2617 if (e1000_is_second_port(hw)) 2618 swfw = E1000_SWFW_PHY1_SM; 2619 2620 if (e1000_swfw_sync_acquire(hw, swfw)) 2621 return -E1000_ERR_SWFW_SYNC; 2622 2623 reg_val = ((reg_addr << E1000_KUMCTRLSTA_OFFSET_SHIFT) 2624 & E1000_KUMCTRLSTA_OFFSET) | data; 2625 E1000_WRITE_REG(hw, KUMCTRLSTA, reg_val); 2626 udelay(2); 2627 2628 return E1000_SUCCESS; 2629 } 2630 2631 static int32_t 2632 e1000_read_kmrn_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t *data) 2633 { 2634 uint16_t swfw = E1000_SWFW_PHY0_SM; 2635 uint32_t reg_val; 2636 DEBUGFUNC(); 2637 2638 if (e1000_is_second_port(hw)) 2639 swfw = E1000_SWFW_PHY1_SM; 2640 2641 if (e1000_swfw_sync_acquire(hw, swfw)) { 2642 debug("%s[%i]\n", __func__, __LINE__); 2643 return -E1000_ERR_SWFW_SYNC; 2644 } 2645 2646 /* Write register address */ 2647 reg_val = ((reg_addr << E1000_KUMCTRLSTA_OFFSET_SHIFT) & 2648 E1000_KUMCTRLSTA_OFFSET) | E1000_KUMCTRLSTA_REN; 2649 E1000_WRITE_REG(hw, KUMCTRLSTA, reg_val); 2650 udelay(2); 2651 2652 /* Read the data returned */ 2653 reg_val = E1000_READ_REG(hw, KUMCTRLSTA); 2654 *data = (uint16_t)reg_val; 2655 2656 return E1000_SUCCESS; 2657 } 2658 2659 /******************************************************************** 2660 * Copper link setup for e1000_phy_gg82563 series. 2661 * 2662 * hw - Struct containing variables accessed by shared code 2663 *********************************************************************/ 2664 static int32_t 2665 e1000_copper_link_ggp_setup(struct e1000_hw *hw) 2666 { 2667 int32_t ret_val; 2668 uint16_t phy_data; 2669 uint32_t reg_data; 2670 2671 DEBUGFUNC(); 2672 2673 if (!hw->phy_reset_disable) { 2674 /* Enable CRS on TX for half-duplex operation. */ 2675 ret_val = e1000_read_phy_reg(hw, 2676 GG82563_PHY_MAC_SPEC_CTRL, &phy_data); 2677 if (ret_val) 2678 return ret_val; 2679 2680 phy_data |= GG82563_MSCR_ASSERT_CRS_ON_TX; 2681 /* Use 25MHz for both link down and 1000BASE-T for Tx clock */ 2682 phy_data |= GG82563_MSCR_TX_CLK_1000MBPS_25MHZ; 2683 2684 ret_val = e1000_write_phy_reg(hw, 2685 GG82563_PHY_MAC_SPEC_CTRL, phy_data); 2686 if (ret_val) 2687 return ret_val; 2688 2689 /* Options: 2690 * MDI/MDI-X = 0 (default) 2691 * 0 - Auto for all speeds 2692 * 1 - MDI mode 2693 * 2 - MDI-X mode 2694 * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes) 2695 */ 2696 ret_val = e1000_read_phy_reg(hw, 2697 GG82563_PHY_SPEC_CTRL, &phy_data); 2698 if (ret_val) 2699 return ret_val; 2700 2701 phy_data &= ~GG82563_PSCR_CROSSOVER_MODE_MASK; 2702 2703 switch (hw->mdix) { 2704 case 1: 2705 phy_data |= GG82563_PSCR_CROSSOVER_MODE_MDI; 2706 break; 2707 case 2: 2708 phy_data |= GG82563_PSCR_CROSSOVER_MODE_MDIX; 2709 break; 2710 case 0: 2711 default: 2712 phy_data |= GG82563_PSCR_CROSSOVER_MODE_AUTO; 2713 break; 2714 } 2715 2716 /* Options: 2717 * disable_polarity_correction = 0 (default) 2718 * Automatic Correction for Reversed Cable Polarity 2719 * 0 - Disabled 2720 * 1 - Enabled 2721 */ 2722 phy_data &= ~GG82563_PSCR_POLARITY_REVERSAL_DISABLE; 2723 ret_val = e1000_write_phy_reg(hw, 2724 GG82563_PHY_SPEC_CTRL, phy_data); 2725 2726 if (ret_val) 2727 return ret_val; 2728 2729 /* SW Reset the PHY so all changes take effect */ 2730 ret_val = e1000_phy_reset(hw); 2731 if (ret_val) { 2732 DEBUGOUT("Error Resetting the PHY\n"); 2733 return ret_val; 2734 } 2735 } /* phy_reset_disable */ 2736 2737 if (hw->mac_type == e1000_80003es2lan) { 2738 /* Bypass RX and TX FIFO's */ 2739 ret_val = e1000_write_kmrn_reg(hw, 2740 E1000_KUMCTRLSTA_OFFSET_FIFO_CTRL, 2741 E1000_KUMCTRLSTA_FIFO_CTRL_RX_BYPASS 2742 | E1000_KUMCTRLSTA_FIFO_CTRL_TX_BYPASS); 2743 if (ret_val) 2744 return ret_val; 2745 2746 ret_val = e1000_read_phy_reg(hw, 2747 GG82563_PHY_SPEC_CTRL_2, &phy_data); 2748 if (ret_val) 2749 return ret_val; 2750 2751 phy_data &= ~GG82563_PSCR2_REVERSE_AUTO_NEG; 2752 ret_val = e1000_write_phy_reg(hw, 2753 GG82563_PHY_SPEC_CTRL_2, phy_data); 2754 2755 if (ret_val) 2756 return ret_val; 2757 2758 reg_data = E1000_READ_REG(hw, CTRL_EXT); 2759 reg_data &= ~(E1000_CTRL_EXT_LINK_MODE_MASK); 2760 E1000_WRITE_REG(hw, CTRL_EXT, reg_data); 2761 2762 ret_val = e1000_read_phy_reg(hw, 2763 GG82563_PHY_PWR_MGMT_CTRL, &phy_data); 2764 if (ret_val) 2765 return ret_val; 2766 2767 /* Do not init these registers when the HW is in IAMT mode, since the 2768 * firmware will have already initialized them. We only initialize 2769 * them if the HW is not in IAMT mode. 2770 */ 2771 if (e1000_check_mng_mode(hw) == false) { 2772 /* Enable Electrical Idle on the PHY */ 2773 phy_data |= GG82563_PMCR_ENABLE_ELECTRICAL_IDLE; 2774 ret_val = e1000_write_phy_reg(hw, 2775 GG82563_PHY_PWR_MGMT_CTRL, phy_data); 2776 if (ret_val) 2777 return ret_val; 2778 2779 ret_val = e1000_read_phy_reg(hw, 2780 GG82563_PHY_KMRN_MODE_CTRL, &phy_data); 2781 if (ret_val) 2782 return ret_val; 2783 2784 phy_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER; 2785 ret_val = e1000_write_phy_reg(hw, 2786 GG82563_PHY_KMRN_MODE_CTRL, phy_data); 2787 2788 if (ret_val) 2789 return ret_val; 2790 } 2791 2792 /* Workaround: Disable padding in Kumeran interface in the MAC 2793 * and in the PHY to avoid CRC errors. 2794 */ 2795 ret_val = e1000_read_phy_reg(hw, 2796 GG82563_PHY_INBAND_CTRL, &phy_data); 2797 if (ret_val) 2798 return ret_val; 2799 phy_data |= GG82563_ICR_DIS_PADDING; 2800 ret_val = e1000_write_phy_reg(hw, 2801 GG82563_PHY_INBAND_CTRL, phy_data); 2802 if (ret_val) 2803 return ret_val; 2804 } 2805 return E1000_SUCCESS; 2806 } 2807 2808 /******************************************************************** 2809 * Copper link setup for e1000_phy_m88 series. 2810 * 2811 * hw - Struct containing variables accessed by shared code 2812 *********************************************************************/ 2813 static int32_t 2814 e1000_copper_link_mgp_setup(struct e1000_hw *hw) 2815 { 2816 int32_t ret_val; 2817 uint16_t phy_data; 2818 2819 DEBUGFUNC(); 2820 2821 if (hw->phy_reset_disable) 2822 return E1000_SUCCESS; 2823 2824 /* Enable CRS on TX. This must be set for half-duplex operation. */ 2825 ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); 2826 if (ret_val) 2827 return ret_val; 2828 2829 phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX; 2830 2831 /* Options: 2832 * MDI/MDI-X = 0 (default) 2833 * 0 - Auto for all speeds 2834 * 1 - MDI mode 2835 * 2 - MDI-X mode 2836 * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes) 2837 */ 2838 phy_data &= ~M88E1000_PSCR_AUTO_X_MODE; 2839 2840 switch (hw->mdix) { 2841 case 1: 2842 phy_data |= M88E1000_PSCR_MDI_MANUAL_MODE; 2843 break; 2844 case 2: 2845 phy_data |= M88E1000_PSCR_MDIX_MANUAL_MODE; 2846 break; 2847 case 3: 2848 phy_data |= M88E1000_PSCR_AUTO_X_1000T; 2849 break; 2850 case 0: 2851 default: 2852 phy_data |= M88E1000_PSCR_AUTO_X_MODE; 2853 break; 2854 } 2855 2856 /* Options: 2857 * disable_polarity_correction = 0 (default) 2858 * Automatic Correction for Reversed Cable Polarity 2859 * 0 - Disabled 2860 * 1 - Enabled 2861 */ 2862 phy_data &= ~M88E1000_PSCR_POLARITY_REVERSAL; 2863 ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data); 2864 if (ret_val) 2865 return ret_val; 2866 2867 if (hw->phy_revision < M88E1011_I_REV_4) { 2868 /* Force TX_CLK in the Extended PHY Specific Control Register 2869 * to 25MHz clock. 2870 */ 2871 ret_val = e1000_read_phy_reg(hw, 2872 M88E1000_EXT_PHY_SPEC_CTRL, &phy_data); 2873 if (ret_val) 2874 return ret_val; 2875 2876 phy_data |= M88E1000_EPSCR_TX_CLK_25; 2877 2878 if ((hw->phy_revision == E1000_REVISION_2) && 2879 (hw->phy_id == M88E1111_I_PHY_ID)) { 2880 /* Vidalia Phy, set the downshift counter to 5x */ 2881 phy_data &= ~(M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK); 2882 phy_data |= M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X; 2883 ret_val = e1000_write_phy_reg(hw, 2884 M88E1000_EXT_PHY_SPEC_CTRL, phy_data); 2885 if (ret_val) 2886 return ret_val; 2887 } else { 2888 /* Configure Master and Slave downshift values */ 2889 phy_data &= ~(M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK 2890 | M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK); 2891 phy_data |= (M88E1000_EPSCR_MASTER_DOWNSHIFT_1X 2892 | M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X); 2893 ret_val = e1000_write_phy_reg(hw, 2894 M88E1000_EXT_PHY_SPEC_CTRL, phy_data); 2895 if (ret_val) 2896 return ret_val; 2897 } 2898 } 2899 2900 /* SW Reset the PHY so all changes take effect */ 2901 ret_val = e1000_phy_reset(hw); 2902 if (ret_val) { 2903 DEBUGOUT("Error Resetting the PHY\n"); 2904 return ret_val; 2905 } 2906 2907 return E1000_SUCCESS; 2908 } 2909 2910 /******************************************************************** 2911 * Setup auto-negotiation and flow control advertisements, 2912 * and then perform auto-negotiation. 2913 * 2914 * hw - Struct containing variables accessed by shared code 2915 *********************************************************************/ 2916 static int32_t 2917 e1000_copper_link_autoneg(struct e1000_hw *hw) 2918 { 2919 int32_t ret_val; 2920 uint16_t phy_data; 2921 2922 DEBUGFUNC(); 2923 2924 /* Perform some bounds checking on the hw->autoneg_advertised 2925 * parameter. If this variable is zero, then set it to the default. 2926 */ 2927 hw->autoneg_advertised &= AUTONEG_ADVERTISE_SPEED_DEFAULT; 2928 2929 /* If autoneg_advertised is zero, we assume it was not defaulted 2930 * by the calling code so we set to advertise full capability. 2931 */ 2932 if (hw->autoneg_advertised == 0) 2933 hw->autoneg_advertised = AUTONEG_ADVERTISE_SPEED_DEFAULT; 2934 2935 /* IFE phy only supports 10/100 */ 2936 if (hw->phy_type == e1000_phy_ife) 2937 hw->autoneg_advertised &= AUTONEG_ADVERTISE_10_100_ALL; 2938 2939 DEBUGOUT("Reconfiguring auto-neg advertisement params\n"); 2940 ret_val = e1000_phy_setup_autoneg(hw); 2941 if (ret_val) { 2942 DEBUGOUT("Error Setting up Auto-Negotiation\n"); 2943 return ret_val; 2944 } 2945 DEBUGOUT("Restarting Auto-Neg\n"); 2946 2947 /* Restart auto-negotiation by setting the Auto Neg Enable bit and 2948 * the Auto Neg Restart bit in the PHY control register. 2949 */ 2950 ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data); 2951 if (ret_val) 2952 return ret_val; 2953 2954 phy_data |= (MII_CR_AUTO_NEG_EN | MII_CR_RESTART_AUTO_NEG); 2955 ret_val = e1000_write_phy_reg(hw, PHY_CTRL, phy_data); 2956 if (ret_val) 2957 return ret_val; 2958 2959 /* Does the user want to wait for Auto-Neg to complete here, or 2960 * check at a later time (for example, callback routine). 2961 */ 2962 /* If we do not wait for autonegtation to complete I 2963 * do not see a valid link status. 2964 * wait_autoneg_complete = 1 . 2965 */ 2966 if (hw->wait_autoneg_complete) { 2967 ret_val = e1000_wait_autoneg(hw); 2968 if (ret_val) { 2969 DEBUGOUT("Error while waiting for autoneg" 2970 "to complete\n"); 2971 return ret_val; 2972 } 2973 } 2974 2975 hw->get_link_status = true; 2976 2977 return E1000_SUCCESS; 2978 } 2979 2980 /****************************************************************************** 2981 * Config the MAC and the PHY after link is up. 2982 * 1) Set up the MAC to the current PHY speed/duplex 2983 * if we are on 82543. If we 2984 * are on newer silicon, we only need to configure 2985 * collision distance in the Transmit Control Register. 2986 * 2) Set up flow control on the MAC to that established with 2987 * the link partner. 2988 * 3) Config DSP to improve Gigabit link quality for some PHY revisions. 2989 * 2990 * hw - Struct containing variables accessed by shared code 2991 ******************************************************************************/ 2992 static int32_t 2993 e1000_copper_link_postconfig(struct e1000_hw *hw) 2994 { 2995 int32_t ret_val; 2996 DEBUGFUNC(); 2997 2998 if (hw->mac_type >= e1000_82544) { 2999 e1000_config_collision_dist(hw); 3000 } else { 3001 ret_val = e1000_config_mac_to_phy(hw); 3002 if (ret_val) { 3003 DEBUGOUT("Error configuring MAC to PHY settings\n"); 3004 return ret_val; 3005 } 3006 } 3007 ret_val = e1000_config_fc_after_link_up(hw); 3008 if (ret_val) { 3009 DEBUGOUT("Error Configuring Flow Control\n"); 3010 return ret_val; 3011 } 3012 return E1000_SUCCESS; 3013 } 3014 3015 /****************************************************************************** 3016 * Detects which PHY is present and setup the speed and duplex 3017 * 3018 * hw - Struct containing variables accessed by shared code 3019 ******************************************************************************/ 3020 static int 3021 e1000_setup_copper_link(struct e1000_hw *hw) 3022 { 3023 int32_t ret_val; 3024 uint16_t i; 3025 uint16_t phy_data; 3026 uint16_t reg_data; 3027 3028 DEBUGFUNC(); 3029 3030 switch (hw->mac_type) { 3031 case e1000_80003es2lan: 3032 case e1000_ich8lan: 3033 /* Set the mac to wait the maximum time between each 3034 * iteration and increase the max iterations when 3035 * polling the phy; this fixes erroneous timeouts at 10Mbps. */ 3036 ret_val = e1000_write_kmrn_reg(hw, 3037 GG82563_REG(0x34, 4), 0xFFFF); 3038 if (ret_val) 3039 return ret_val; 3040 ret_val = e1000_read_kmrn_reg(hw, 3041 GG82563_REG(0x34, 9), ®_data); 3042 if (ret_val) 3043 return ret_val; 3044 reg_data |= 0x3F; 3045 ret_val = e1000_write_kmrn_reg(hw, 3046 GG82563_REG(0x34, 9), reg_data); 3047 if (ret_val) 3048 return ret_val; 3049 default: 3050 break; 3051 } 3052 3053 /* Check if it is a valid PHY and set PHY mode if necessary. */ 3054 ret_val = e1000_copper_link_preconfig(hw); 3055 if (ret_val) 3056 return ret_val; 3057 switch (hw->mac_type) { 3058 case e1000_80003es2lan: 3059 /* Kumeran registers are written-only */ 3060 reg_data = 3061 E1000_KUMCTRLSTA_INB_CTRL_LINK_STATUS_TX_TIMEOUT_DEFAULT; 3062 reg_data |= E1000_KUMCTRLSTA_INB_CTRL_DIS_PADDING; 3063 ret_val = e1000_write_kmrn_reg(hw, 3064 E1000_KUMCTRLSTA_OFFSET_INB_CTRL, reg_data); 3065 if (ret_val) 3066 return ret_val; 3067 break; 3068 default: 3069 break; 3070 } 3071 3072 if (hw->phy_type == e1000_phy_igp || 3073 hw->phy_type == e1000_phy_igp_3 || 3074 hw->phy_type == e1000_phy_igp_2) { 3075 ret_val = e1000_copper_link_igp_setup(hw); 3076 if (ret_val) 3077 return ret_val; 3078 } else if (hw->phy_type == e1000_phy_m88 || 3079 hw->phy_type == e1000_phy_igb) { 3080 ret_val = e1000_copper_link_mgp_setup(hw); 3081 if (ret_val) 3082 return ret_val; 3083 } else if (hw->phy_type == e1000_phy_gg82563) { 3084 ret_val = e1000_copper_link_ggp_setup(hw); 3085 if (ret_val) 3086 return ret_val; 3087 } 3088 3089 /* always auto */ 3090 /* Setup autoneg and flow control advertisement 3091 * and perform autonegotiation */ 3092 ret_val = e1000_copper_link_autoneg(hw); 3093 if (ret_val) 3094 return ret_val; 3095 3096 /* Check link status. Wait up to 100 microseconds for link to become 3097 * valid. 3098 */ 3099 for (i = 0; i < 10; i++) { 3100 ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data); 3101 if (ret_val) 3102 return ret_val; 3103 ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data); 3104 if (ret_val) 3105 return ret_val; 3106 3107 if (phy_data & MII_SR_LINK_STATUS) { 3108 /* Config the MAC and PHY after link is up */ 3109 ret_val = e1000_copper_link_postconfig(hw); 3110 if (ret_val) 3111 return ret_val; 3112 3113 DEBUGOUT("Valid link established!!!\n"); 3114 return E1000_SUCCESS; 3115 } 3116 udelay(10); 3117 } 3118 3119 DEBUGOUT("Unable to establish link!!!\n"); 3120 return E1000_SUCCESS; 3121 } 3122 3123 /****************************************************************************** 3124 * Configures PHY autoneg and flow control advertisement settings 3125 * 3126 * hw - Struct containing variables accessed by shared code 3127 ******************************************************************************/ 3128 int32_t 3129 e1000_phy_setup_autoneg(struct e1000_hw *hw) 3130 { 3131 int32_t ret_val; 3132 uint16_t mii_autoneg_adv_reg; 3133 uint16_t mii_1000t_ctrl_reg; 3134 3135 DEBUGFUNC(); 3136 3137 /* Read the MII Auto-Neg Advertisement Register (Address 4). */ 3138 ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_ADV, &mii_autoneg_adv_reg); 3139 if (ret_val) 3140 return ret_val; 3141 3142 if (hw->phy_type != e1000_phy_ife) { 3143 /* Read the MII 1000Base-T Control Register (Address 9). */ 3144 ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, 3145 &mii_1000t_ctrl_reg); 3146 if (ret_val) 3147 return ret_val; 3148 } else 3149 mii_1000t_ctrl_reg = 0; 3150 3151 /* Need to parse both autoneg_advertised and fc and set up 3152 * the appropriate PHY registers. First we will parse for 3153 * autoneg_advertised software override. Since we can advertise 3154 * a plethora of combinations, we need to check each bit 3155 * individually. 3156 */ 3157 3158 /* First we clear all the 10/100 mb speed bits in the Auto-Neg 3159 * Advertisement Register (Address 4) and the 1000 mb speed bits in 3160 * the 1000Base-T Control Register (Address 9). 3161 */ 3162 mii_autoneg_adv_reg &= ~REG4_SPEED_MASK; 3163 mii_1000t_ctrl_reg &= ~REG9_SPEED_MASK; 3164 3165 DEBUGOUT("autoneg_advertised %x\n", hw->autoneg_advertised); 3166 3167 /* Do we want to advertise 10 Mb Half Duplex? */ 3168 if (hw->autoneg_advertised & ADVERTISE_10_HALF) { 3169 DEBUGOUT("Advertise 10mb Half duplex\n"); 3170 mii_autoneg_adv_reg |= NWAY_AR_10T_HD_CAPS; 3171 } 3172 3173 /* Do we want to advertise 10 Mb Full Duplex? */ 3174 if (hw->autoneg_advertised & ADVERTISE_10_FULL) { 3175 DEBUGOUT("Advertise 10mb Full duplex\n"); 3176 mii_autoneg_adv_reg |= NWAY_AR_10T_FD_CAPS; 3177 } 3178 3179 /* Do we want to advertise 100 Mb Half Duplex? */ 3180 if (hw->autoneg_advertised & ADVERTISE_100_HALF) { 3181 DEBUGOUT("Advertise 100mb Half duplex\n"); 3182 mii_autoneg_adv_reg |= NWAY_AR_100TX_HD_CAPS; 3183 } 3184 3185 /* Do we want to advertise 100 Mb Full Duplex? */ 3186 if (hw->autoneg_advertised & ADVERTISE_100_FULL) { 3187 DEBUGOUT("Advertise 100mb Full duplex\n"); 3188 mii_autoneg_adv_reg |= NWAY_AR_100TX_FD_CAPS; 3189 } 3190 3191 /* We do not allow the Phy to advertise 1000 Mb Half Duplex */ 3192 if (hw->autoneg_advertised & ADVERTISE_1000_HALF) { 3193 DEBUGOUT 3194 ("Advertise 1000mb Half duplex requested, request denied!\n"); 3195 } 3196 3197 /* Do we want to advertise 1000 Mb Full Duplex? */ 3198 if (hw->autoneg_advertised & ADVERTISE_1000_FULL) { 3199 DEBUGOUT("Advertise 1000mb Full duplex\n"); 3200 mii_1000t_ctrl_reg |= CR_1000T_FD_CAPS; 3201 } 3202 3203 /* Check for a software override of the flow control settings, and 3204 * setup the PHY advertisement registers accordingly. If 3205 * auto-negotiation is enabled, then software will have to set the 3206 * "PAUSE" bits to the correct value in the Auto-Negotiation 3207 * Advertisement Register (PHY_AUTONEG_ADV) and re-start auto-negotiation. 3208 * 3209 * The possible values of the "fc" parameter are: 3210 * 0: Flow control is completely disabled 3211 * 1: Rx flow control is enabled (we can receive pause frames 3212 * but not send pause frames). 3213 * 2: Tx flow control is enabled (we can send pause frames 3214 * but we do not support receiving pause frames). 3215 * 3: Both Rx and TX flow control (symmetric) are enabled. 3216 * other: No software override. The flow control configuration 3217 * in the EEPROM is used. 3218 */ 3219 switch (hw->fc) { 3220 case e1000_fc_none: /* 0 */ 3221 /* Flow control (RX & TX) is completely disabled by a 3222 * software over-ride. 3223 */ 3224 mii_autoneg_adv_reg &= ~(NWAY_AR_ASM_DIR | NWAY_AR_PAUSE); 3225 break; 3226 case e1000_fc_rx_pause: /* 1 */ 3227 /* RX Flow control is enabled, and TX Flow control is 3228 * disabled, by a software over-ride. 3229 */ 3230 /* Since there really isn't a way to advertise that we are 3231 * capable of RX Pause ONLY, we will advertise that we 3232 * support both symmetric and asymmetric RX PAUSE. Later 3233 * (in e1000_config_fc_after_link_up) we will disable the 3234 *hw's ability to send PAUSE frames. 3235 */ 3236 mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE); 3237 break; 3238 case e1000_fc_tx_pause: /* 2 */ 3239 /* TX Flow control is enabled, and RX Flow control is 3240 * disabled, by a software over-ride. 3241 */ 3242 mii_autoneg_adv_reg |= NWAY_AR_ASM_DIR; 3243 mii_autoneg_adv_reg &= ~NWAY_AR_PAUSE; 3244 break; 3245 case e1000_fc_full: /* 3 */ 3246 /* Flow control (both RX and TX) is enabled by a software 3247 * over-ride. 3248 */ 3249 mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE); 3250 break; 3251 default: 3252 DEBUGOUT("Flow control param set incorrectly\n"); 3253 return -E1000_ERR_CONFIG; 3254 } 3255 3256 ret_val = e1000_write_phy_reg(hw, PHY_AUTONEG_ADV, mii_autoneg_adv_reg); 3257 if (ret_val) 3258 return ret_val; 3259 3260 DEBUGOUT("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg); 3261 3262 if (hw->phy_type != e1000_phy_ife) { 3263 ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, 3264 mii_1000t_ctrl_reg); 3265 if (ret_val) 3266 return ret_val; 3267 } 3268 3269 return E1000_SUCCESS; 3270 } 3271 3272 /****************************************************************************** 3273 * Sets the collision distance in the Transmit Control register 3274 * 3275 * hw - Struct containing variables accessed by shared code 3276 * 3277 * Link should have been established previously. Reads the speed and duplex 3278 * information from the Device Status register. 3279 ******************************************************************************/ 3280 static void 3281 e1000_config_collision_dist(struct e1000_hw *hw) 3282 { 3283 uint32_t tctl, coll_dist; 3284 3285 DEBUGFUNC(); 3286 3287 if (hw->mac_type < e1000_82543) 3288 coll_dist = E1000_COLLISION_DISTANCE_82542; 3289 else 3290 coll_dist = E1000_COLLISION_DISTANCE; 3291 3292 tctl = E1000_READ_REG(hw, TCTL); 3293 3294 tctl &= ~E1000_TCTL_COLD; 3295 tctl |= coll_dist << E1000_COLD_SHIFT; 3296 3297 E1000_WRITE_REG(hw, TCTL, tctl); 3298 E1000_WRITE_FLUSH(hw); 3299 } 3300 3301 /****************************************************************************** 3302 * Sets MAC speed and duplex settings to reflect the those in the PHY 3303 * 3304 * hw - Struct containing variables accessed by shared code 3305 * mii_reg - data to write to the MII control register 3306 * 3307 * The contents of the PHY register containing the needed information need to 3308 * be passed in. 3309 ******************************************************************************/ 3310 static int 3311 e1000_config_mac_to_phy(struct e1000_hw *hw) 3312 { 3313 uint32_t ctrl; 3314 uint16_t phy_data; 3315 3316 DEBUGFUNC(); 3317 3318 /* Read the Device Control Register and set the bits to Force Speed 3319 * and Duplex. 3320 */ 3321 ctrl = E1000_READ_REG(hw, CTRL); 3322 ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); 3323 ctrl &= ~(E1000_CTRL_ILOS); 3324 ctrl |= (E1000_CTRL_SPD_SEL); 3325 3326 /* Set up duplex in the Device Control and Transmit Control 3327 * registers depending on negotiated values. 3328 */ 3329 if (e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data) < 0) { 3330 DEBUGOUT("PHY Read Error\n"); 3331 return -E1000_ERR_PHY; 3332 } 3333 if (phy_data & M88E1000_PSSR_DPLX) 3334 ctrl |= E1000_CTRL_FD; 3335 else 3336 ctrl &= ~E1000_CTRL_FD; 3337 3338 e1000_config_collision_dist(hw); 3339 3340 /* Set up speed in the Device Control register depending on 3341 * negotiated values. 3342 */ 3343 if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS) 3344 ctrl |= E1000_CTRL_SPD_1000; 3345 else if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_100MBS) 3346 ctrl |= E1000_CTRL_SPD_100; 3347 /* Write the configured values back to the Device Control Reg. */ 3348 E1000_WRITE_REG(hw, CTRL, ctrl); 3349 return 0; 3350 } 3351 3352 /****************************************************************************** 3353 * Forces the MAC's flow control settings. 3354 * 3355 * hw - Struct containing variables accessed by shared code 3356 * 3357 * Sets the TFCE and RFCE bits in the device control register to reflect 3358 * the adapter settings. TFCE and RFCE need to be explicitly set by 3359 * software when a Copper PHY is used because autonegotiation is managed 3360 * by the PHY rather than the MAC. Software must also configure these 3361 * bits when link is forced on a fiber connection. 3362 *****************************************************************************/ 3363 static int 3364 e1000_force_mac_fc(struct e1000_hw *hw) 3365 { 3366 uint32_t ctrl; 3367 3368 DEBUGFUNC(); 3369 3370 /* Get the current configuration of the Device Control Register */ 3371 ctrl = E1000_READ_REG(hw, CTRL); 3372 3373 /* Because we didn't get link via the internal auto-negotiation 3374 * mechanism (we either forced link or we got link via PHY 3375 * auto-neg), we have to manually enable/disable transmit an 3376 * receive flow control. 3377 * 3378 * The "Case" statement below enables/disable flow control 3379 * according to the "hw->fc" parameter. 3380 * 3381 * The possible values of the "fc" parameter are: 3382 * 0: Flow control is completely disabled 3383 * 1: Rx flow control is enabled (we can receive pause 3384 * frames but not send pause frames). 3385 * 2: Tx flow control is enabled (we can send pause frames 3386 * frames but we do not receive pause frames). 3387 * 3: Both Rx and TX flow control (symmetric) is enabled. 3388 * other: No other values should be possible at this point. 3389 */ 3390 3391 switch (hw->fc) { 3392 case e1000_fc_none: 3393 ctrl &= (~(E1000_CTRL_TFCE | E1000_CTRL_RFCE)); 3394 break; 3395 case e1000_fc_rx_pause: 3396 ctrl &= (~E1000_CTRL_TFCE); 3397 ctrl |= E1000_CTRL_RFCE; 3398 break; 3399 case e1000_fc_tx_pause: 3400 ctrl &= (~E1000_CTRL_RFCE); 3401 ctrl |= E1000_CTRL_TFCE; 3402 break; 3403 case e1000_fc_full: 3404 ctrl |= (E1000_CTRL_TFCE | E1000_CTRL_RFCE); 3405 break; 3406 default: 3407 DEBUGOUT("Flow control param set incorrectly\n"); 3408 return -E1000_ERR_CONFIG; 3409 } 3410 3411 /* Disable TX Flow Control for 82542 (rev 2.0) */ 3412 if (hw->mac_type == e1000_82542_rev2_0) 3413 ctrl &= (~E1000_CTRL_TFCE); 3414 3415 E1000_WRITE_REG(hw, CTRL, ctrl); 3416 return 0; 3417 } 3418 3419 /****************************************************************************** 3420 * Configures flow control settings after link is established 3421 * 3422 * hw - Struct containing variables accessed by shared code 3423 * 3424 * Should be called immediately after a valid link has been established. 3425 * Forces MAC flow control settings if link was forced. When in MII/GMII mode 3426 * and autonegotiation is enabled, the MAC flow control settings will be set 3427 * based on the flow control negotiated by the PHY. In TBI mode, the TFCE 3428 * and RFCE bits will be automaticaly set to the negotiated flow control mode. 3429 *****************************************************************************/ 3430 static int32_t 3431 e1000_config_fc_after_link_up(struct e1000_hw *hw) 3432 { 3433 int32_t ret_val; 3434 uint16_t mii_status_reg; 3435 uint16_t mii_nway_adv_reg; 3436 uint16_t mii_nway_lp_ability_reg; 3437 uint16_t speed; 3438 uint16_t duplex; 3439 3440 DEBUGFUNC(); 3441 3442 /* Check for the case where we have fiber media and auto-neg failed 3443 * so we had to force link. In this case, we need to force the 3444 * configuration of the MAC to match the "fc" parameter. 3445 */ 3446 if (((hw->media_type == e1000_media_type_fiber) && (hw->autoneg_failed)) 3447 || ((hw->media_type == e1000_media_type_internal_serdes) 3448 && (hw->autoneg_failed)) 3449 || ((hw->media_type == e1000_media_type_copper) 3450 && (!hw->autoneg))) { 3451 ret_val = e1000_force_mac_fc(hw); 3452 if (ret_val < 0) { 3453 DEBUGOUT("Error forcing flow control settings\n"); 3454 return ret_val; 3455 } 3456 } 3457 3458 /* Check for the case where we have copper media and auto-neg is 3459 * enabled. In this case, we need to check and see if Auto-Neg 3460 * has completed, and if so, how the PHY and link partner has 3461 * flow control configured. 3462 */ 3463 if (hw->media_type == e1000_media_type_copper) { 3464 /* Read the MII Status Register and check to see if AutoNeg 3465 * has completed. We read this twice because this reg has 3466 * some "sticky" (latched) bits. 3467 */ 3468 if (e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg) < 0) { 3469 DEBUGOUT("PHY Read Error\n"); 3470 return -E1000_ERR_PHY; 3471 } 3472 if (e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg) < 0) { 3473 DEBUGOUT("PHY Read Error\n"); 3474 return -E1000_ERR_PHY; 3475 } 3476 3477 if (mii_status_reg & MII_SR_AUTONEG_COMPLETE) { 3478 /* The AutoNeg process has completed, so we now need to 3479 * read both the Auto Negotiation Advertisement Register 3480 * (Address 4) and the Auto_Negotiation Base Page Ability 3481 * Register (Address 5) to determine how flow control was 3482 * negotiated. 3483 */ 3484 if (e1000_read_phy_reg 3485 (hw, PHY_AUTONEG_ADV, &mii_nway_adv_reg) < 0) { 3486 DEBUGOUT("PHY Read Error\n"); 3487 return -E1000_ERR_PHY; 3488 } 3489 if (e1000_read_phy_reg 3490 (hw, PHY_LP_ABILITY, 3491 &mii_nway_lp_ability_reg) < 0) { 3492 DEBUGOUT("PHY Read Error\n"); 3493 return -E1000_ERR_PHY; 3494 } 3495 3496 /* Two bits in the Auto Negotiation Advertisement Register 3497 * (Address 4) and two bits in the Auto Negotiation Base 3498 * Page Ability Register (Address 5) determine flow control 3499 * for both the PHY and the link partner. The following 3500 * table, taken out of the IEEE 802.3ab/D6.0 dated March 25, 3501 * 1999, describes these PAUSE resolution bits and how flow 3502 * control is determined based upon these settings. 3503 * NOTE: DC = Don't Care 3504 * 3505 * LOCAL DEVICE | LINK PARTNER 3506 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | NIC Resolution 3507 *-------|---------|-------|---------|-------------------- 3508 * 0 | 0 | DC | DC | e1000_fc_none 3509 * 0 | 1 | 0 | DC | e1000_fc_none 3510 * 0 | 1 | 1 | 0 | e1000_fc_none 3511 * 0 | 1 | 1 | 1 | e1000_fc_tx_pause 3512 * 1 | 0 | 0 | DC | e1000_fc_none 3513 * 1 | DC | 1 | DC | e1000_fc_full 3514 * 1 | 1 | 0 | 0 | e1000_fc_none 3515 * 1 | 1 | 0 | 1 | e1000_fc_rx_pause 3516 * 3517 */ 3518 /* Are both PAUSE bits set to 1? If so, this implies 3519 * Symmetric Flow Control is enabled at both ends. The 3520 * ASM_DIR bits are irrelevant per the spec. 3521 * 3522 * For Symmetric Flow Control: 3523 * 3524 * LOCAL DEVICE | LINK PARTNER 3525 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result 3526 *-------|---------|-------|---------|-------------------- 3527 * 1 | DC | 1 | DC | e1000_fc_full 3528 * 3529 */ 3530 if ((mii_nway_adv_reg & NWAY_AR_PAUSE) && 3531 (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE)) { 3532 /* Now we need to check if the user selected RX ONLY 3533 * of pause frames. In this case, we had to advertise 3534 * FULL flow control because we could not advertise RX 3535 * ONLY. Hence, we must now check to see if we need to 3536 * turn OFF the TRANSMISSION of PAUSE frames. 3537 */ 3538 if (hw->original_fc == e1000_fc_full) { 3539 hw->fc = e1000_fc_full; 3540 DEBUGOUT("Flow Control = FULL.\r\n"); 3541 } else { 3542 hw->fc = e1000_fc_rx_pause; 3543 DEBUGOUT 3544 ("Flow Control = RX PAUSE frames only.\r\n"); 3545 } 3546 } 3547 /* For receiving PAUSE frames ONLY. 3548 * 3549 * LOCAL DEVICE | LINK PARTNER 3550 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result 3551 *-------|---------|-------|---------|-------------------- 3552 * 0 | 1 | 1 | 1 | e1000_fc_tx_pause 3553 * 3554 */ 3555 else if (!(mii_nway_adv_reg & NWAY_AR_PAUSE) && 3556 (mii_nway_adv_reg & NWAY_AR_ASM_DIR) && 3557 (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) && 3558 (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) 3559 { 3560 hw->fc = e1000_fc_tx_pause; 3561 DEBUGOUT 3562 ("Flow Control = TX PAUSE frames only.\r\n"); 3563 } 3564 /* For transmitting PAUSE frames ONLY. 3565 * 3566 * LOCAL DEVICE | LINK PARTNER 3567 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result 3568 *-------|---------|-------|---------|-------------------- 3569 * 1 | 1 | 0 | 1 | e1000_fc_rx_pause 3570 * 3571 */ 3572 else if ((mii_nway_adv_reg & NWAY_AR_PAUSE) && 3573 (mii_nway_adv_reg & NWAY_AR_ASM_DIR) && 3574 !(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) && 3575 (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) 3576 { 3577 hw->fc = e1000_fc_rx_pause; 3578 DEBUGOUT 3579 ("Flow Control = RX PAUSE frames only.\r\n"); 3580 } 3581 /* Per the IEEE spec, at this point flow control should be 3582 * disabled. However, we want to consider that we could 3583 * be connected to a legacy switch that doesn't advertise 3584 * desired flow control, but can be forced on the link 3585 * partner. So if we advertised no flow control, that is 3586 * what we will resolve to. If we advertised some kind of 3587 * receive capability (Rx Pause Only or Full Flow Control) 3588 * and the link partner advertised none, we will configure 3589 * ourselves to enable Rx Flow Control only. We can do 3590 * this safely for two reasons: If the link partner really 3591 * didn't want flow control enabled, and we enable Rx, no 3592 * harm done since we won't be receiving any PAUSE frames 3593 * anyway. If the intent on the link partner was to have 3594 * flow control enabled, then by us enabling RX only, we 3595 * can at least receive pause frames and process them. 3596 * This is a good idea because in most cases, since we are 3597 * predominantly a server NIC, more times than not we will 3598 * be asked to delay transmission of packets than asking 3599 * our link partner to pause transmission of frames. 3600 */ 3601 else if (hw->original_fc == e1000_fc_none || 3602 hw->original_fc == e1000_fc_tx_pause) { 3603 hw->fc = e1000_fc_none; 3604 DEBUGOUT("Flow Control = NONE.\r\n"); 3605 } else { 3606 hw->fc = e1000_fc_rx_pause; 3607 DEBUGOUT 3608 ("Flow Control = RX PAUSE frames only.\r\n"); 3609 } 3610 3611 /* Now we need to do one last check... If we auto- 3612 * negotiated to HALF DUPLEX, flow control should not be 3613 * enabled per IEEE 802.3 spec. 3614 */ 3615 e1000_get_speed_and_duplex(hw, &speed, &duplex); 3616 3617 if (duplex == HALF_DUPLEX) 3618 hw->fc = e1000_fc_none; 3619 3620 /* Now we call a subroutine to actually force the MAC 3621 * controller to use the correct flow control settings. 3622 */ 3623 ret_val = e1000_force_mac_fc(hw); 3624 if (ret_val < 0) { 3625 DEBUGOUT 3626 ("Error forcing flow control settings\n"); 3627 return ret_val; 3628 } 3629 } else { 3630 DEBUGOUT 3631 ("Copper PHY and Auto Neg has not completed.\r\n"); 3632 } 3633 } 3634 return E1000_SUCCESS; 3635 } 3636 3637 /****************************************************************************** 3638 * Checks to see if the link status of the hardware has changed. 3639 * 3640 * hw - Struct containing variables accessed by shared code 3641 * 3642 * Called by any function that needs to check the link status of the adapter. 3643 *****************************************************************************/ 3644 static int 3645 e1000_check_for_link(struct e1000_hw *hw) 3646 { 3647 uint32_t rxcw; 3648 uint32_t ctrl; 3649 uint32_t status; 3650 uint32_t rctl; 3651 uint32_t signal; 3652 int32_t ret_val; 3653 uint16_t phy_data; 3654 uint16_t lp_capability; 3655 3656 DEBUGFUNC(); 3657 3658 /* On adapters with a MAC newer that 82544, SW Defineable pin 1 will be 3659 * set when the optics detect a signal. On older adapters, it will be 3660 * cleared when there is a signal 3661 */ 3662 ctrl = E1000_READ_REG(hw, CTRL); 3663 if ((hw->mac_type > e1000_82544) && !(ctrl & E1000_CTRL_ILOS)) 3664 signal = E1000_CTRL_SWDPIN1; 3665 else 3666 signal = 0; 3667 3668 status = E1000_READ_REG(hw, STATUS); 3669 rxcw = E1000_READ_REG(hw, RXCW); 3670 DEBUGOUT("ctrl: %#08x status %#08x rxcw %#08x\n", ctrl, status, rxcw); 3671 3672 /* If we have a copper PHY then we only want to go out to the PHY 3673 * registers to see if Auto-Neg has completed and/or if our link 3674 * status has changed. The get_link_status flag will be set if we 3675 * receive a Link Status Change interrupt or we have Rx Sequence 3676 * Errors. 3677 */ 3678 if ((hw->media_type == e1000_media_type_copper) && hw->get_link_status) { 3679 /* First we want to see if the MII Status Register reports 3680 * link. If so, then we want to get the current speed/duplex 3681 * of the PHY. 3682 * Read the register twice since the link bit is sticky. 3683 */ 3684 if (e1000_read_phy_reg(hw, PHY_STATUS, &phy_data) < 0) { 3685 DEBUGOUT("PHY Read Error\n"); 3686 return -E1000_ERR_PHY; 3687 } 3688 if (e1000_read_phy_reg(hw, PHY_STATUS, &phy_data) < 0) { 3689 DEBUGOUT("PHY Read Error\n"); 3690 return -E1000_ERR_PHY; 3691 } 3692 3693 if (phy_data & MII_SR_LINK_STATUS) { 3694 hw->get_link_status = false; 3695 } else { 3696 /* No link detected */ 3697 return -E1000_ERR_NOLINK; 3698 } 3699 3700 /* We have a M88E1000 PHY and Auto-Neg is enabled. If we 3701 * have Si on board that is 82544 or newer, Auto 3702 * Speed Detection takes care of MAC speed/duplex 3703 * configuration. So we only need to configure Collision 3704 * Distance in the MAC. Otherwise, we need to force 3705 * speed/duplex on the MAC to the current PHY speed/duplex 3706 * settings. 3707 */ 3708 if (hw->mac_type >= e1000_82544) 3709 e1000_config_collision_dist(hw); 3710 else { 3711 ret_val = e1000_config_mac_to_phy(hw); 3712 if (ret_val < 0) { 3713 DEBUGOUT 3714 ("Error configuring MAC to PHY settings\n"); 3715 return ret_val; 3716 } 3717 } 3718 3719 /* Configure Flow Control now that Auto-Neg has completed. First, we 3720 * need to restore the desired flow control settings because we may 3721 * have had to re-autoneg with a different link partner. 3722 */ 3723 ret_val = e1000_config_fc_after_link_up(hw); 3724 if (ret_val < 0) { 3725 DEBUGOUT("Error configuring flow control\n"); 3726 return ret_val; 3727 } 3728 3729 /* At this point we know that we are on copper and we have 3730 * auto-negotiated link. These are conditions for checking the link 3731 * parter capability register. We use the link partner capability to 3732 * determine if TBI Compatibility needs to be turned on or off. If 3733 * the link partner advertises any speed in addition to Gigabit, then 3734 * we assume that they are GMII-based, and TBI compatibility is not 3735 * needed. If no other speeds are advertised, we assume the link 3736 * partner is TBI-based, and we turn on TBI Compatibility. 3737 */ 3738 if (hw->tbi_compatibility_en) { 3739 if (e1000_read_phy_reg 3740 (hw, PHY_LP_ABILITY, &lp_capability) < 0) { 3741 DEBUGOUT("PHY Read Error\n"); 3742 return -E1000_ERR_PHY; 3743 } 3744 if (lp_capability & (NWAY_LPAR_10T_HD_CAPS | 3745 NWAY_LPAR_10T_FD_CAPS | 3746 NWAY_LPAR_100TX_HD_CAPS | 3747 NWAY_LPAR_100TX_FD_CAPS | 3748 NWAY_LPAR_100T4_CAPS)) { 3749 /* If our link partner advertises anything in addition to 3750 * gigabit, we do not need to enable TBI compatibility. 3751 */ 3752 if (hw->tbi_compatibility_on) { 3753 /* If we previously were in the mode, turn it off. */ 3754 rctl = E1000_READ_REG(hw, RCTL); 3755 rctl &= ~E1000_RCTL_SBP; 3756 E1000_WRITE_REG(hw, RCTL, rctl); 3757 hw->tbi_compatibility_on = false; 3758 } 3759 } else { 3760 /* If TBI compatibility is was previously off, turn it on. For 3761 * compatibility with a TBI link partner, we will store bad 3762 * packets. Some frames have an additional byte on the end and 3763 * will look like CRC errors to to the hardware. 3764 */ 3765 if (!hw->tbi_compatibility_on) { 3766 hw->tbi_compatibility_on = true; 3767 rctl = E1000_READ_REG(hw, RCTL); 3768 rctl |= E1000_RCTL_SBP; 3769 E1000_WRITE_REG(hw, RCTL, rctl); 3770 } 3771 } 3772 } 3773 } 3774 /* If we don't have link (auto-negotiation failed or link partner cannot 3775 * auto-negotiate), the cable is plugged in (we have signal), and our 3776 * link partner is not trying to auto-negotiate with us (we are receiving 3777 * idles or data), we need to force link up. We also need to give 3778 * auto-negotiation time to complete, in case the cable was just plugged 3779 * in. The autoneg_failed flag does this. 3780 */ 3781 else if ((hw->media_type == e1000_media_type_fiber) && 3782 (!(status & E1000_STATUS_LU)) && 3783 ((ctrl & E1000_CTRL_SWDPIN1) == signal) && 3784 (!(rxcw & E1000_RXCW_C))) { 3785 if (hw->autoneg_failed == 0) { 3786 hw->autoneg_failed = 1; 3787 return 0; 3788 } 3789 DEBUGOUT("NOT RXing /C/, disable AutoNeg and force link.\r\n"); 3790 3791 /* Disable auto-negotiation in the TXCW register */ 3792 E1000_WRITE_REG(hw, TXCW, (hw->txcw & ~E1000_TXCW_ANE)); 3793 3794 /* Force link-up and also force full-duplex. */ 3795 ctrl = E1000_READ_REG(hw, CTRL); 3796 ctrl |= (E1000_CTRL_SLU | E1000_CTRL_FD); 3797 E1000_WRITE_REG(hw, CTRL, ctrl); 3798 3799 /* Configure Flow Control after forcing link up. */ 3800 ret_val = e1000_config_fc_after_link_up(hw); 3801 if (ret_val < 0) { 3802 DEBUGOUT("Error configuring flow control\n"); 3803 return ret_val; 3804 } 3805 } 3806 /* If we are forcing link and we are receiving /C/ ordered sets, re-enable 3807 * auto-negotiation in the TXCW register and disable forced link in the 3808 * Device Control register in an attempt to auto-negotiate with our link 3809 * partner. 3810 */ 3811 else if ((hw->media_type == e1000_media_type_fiber) && 3812 (ctrl & E1000_CTRL_SLU) && (rxcw & E1000_RXCW_C)) { 3813 DEBUGOUT 3814 ("RXing /C/, enable AutoNeg and stop forcing link.\r\n"); 3815 E1000_WRITE_REG(hw, TXCW, hw->txcw); 3816 E1000_WRITE_REG(hw, CTRL, (ctrl & ~E1000_CTRL_SLU)); 3817 } 3818 return 0; 3819 } 3820 3821 /****************************************************************************** 3822 * Configure the MAC-to-PHY interface for 10/100Mbps 3823 * 3824 * hw - Struct containing variables accessed by shared code 3825 ******************************************************************************/ 3826 static int32_t 3827 e1000_configure_kmrn_for_10_100(struct e1000_hw *hw, uint16_t duplex) 3828 { 3829 int32_t ret_val = E1000_SUCCESS; 3830 uint32_t tipg; 3831 uint16_t reg_data; 3832 3833 DEBUGFUNC(); 3834 3835 reg_data = E1000_KUMCTRLSTA_HD_CTRL_10_100_DEFAULT; 3836 ret_val = e1000_write_kmrn_reg(hw, 3837 E1000_KUMCTRLSTA_OFFSET_HD_CTRL, reg_data); 3838 if (ret_val) 3839 return ret_val; 3840 3841 /* Configure Transmit Inter-Packet Gap */ 3842 tipg = E1000_READ_REG(hw, TIPG); 3843 tipg &= ~E1000_TIPG_IPGT_MASK; 3844 tipg |= DEFAULT_80003ES2LAN_TIPG_IPGT_10_100; 3845 E1000_WRITE_REG(hw, TIPG, tipg); 3846 3847 ret_val = e1000_read_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, ®_data); 3848 3849 if (ret_val) 3850 return ret_val; 3851 3852 if (duplex == HALF_DUPLEX) 3853 reg_data |= GG82563_KMCR_PASS_FALSE_CARRIER; 3854 else 3855 reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER; 3856 3857 ret_val = e1000_write_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data); 3858 3859 return ret_val; 3860 } 3861 3862 static int32_t 3863 e1000_configure_kmrn_for_1000(struct e1000_hw *hw) 3864 { 3865 int32_t ret_val = E1000_SUCCESS; 3866 uint16_t reg_data; 3867 uint32_t tipg; 3868 3869 DEBUGFUNC(); 3870 3871 reg_data = E1000_KUMCTRLSTA_HD_CTRL_1000_DEFAULT; 3872 ret_val = e1000_write_kmrn_reg(hw, 3873 E1000_KUMCTRLSTA_OFFSET_HD_CTRL, reg_data); 3874 if (ret_val) 3875 return ret_val; 3876 3877 /* Configure Transmit Inter-Packet Gap */ 3878 tipg = E1000_READ_REG(hw, TIPG); 3879 tipg &= ~E1000_TIPG_IPGT_MASK; 3880 tipg |= DEFAULT_80003ES2LAN_TIPG_IPGT_1000; 3881 E1000_WRITE_REG(hw, TIPG, tipg); 3882 3883 ret_val = e1000_read_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, ®_data); 3884 3885 if (ret_val) 3886 return ret_val; 3887 3888 reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER; 3889 ret_val = e1000_write_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data); 3890 3891 return ret_val; 3892 } 3893 3894 /****************************************************************************** 3895 * Detects the current speed and duplex settings of the hardware. 3896 * 3897 * hw - Struct containing variables accessed by shared code 3898 * speed - Speed of the connection 3899 * duplex - Duplex setting of the connection 3900 *****************************************************************************/ 3901 static int 3902 e1000_get_speed_and_duplex(struct e1000_hw *hw, uint16_t *speed, 3903 uint16_t *duplex) 3904 { 3905 uint32_t status; 3906 int32_t ret_val; 3907 uint16_t phy_data; 3908 3909 DEBUGFUNC(); 3910 3911 if (hw->mac_type >= e1000_82543) { 3912 status = E1000_READ_REG(hw, STATUS); 3913 if (status & E1000_STATUS_SPEED_1000) { 3914 *speed = SPEED_1000; 3915 DEBUGOUT("1000 Mbs, "); 3916 } else if (status & E1000_STATUS_SPEED_100) { 3917 *speed = SPEED_100; 3918 DEBUGOUT("100 Mbs, "); 3919 } else { 3920 *speed = SPEED_10; 3921 DEBUGOUT("10 Mbs, "); 3922 } 3923 3924 if (status & E1000_STATUS_FD) { 3925 *duplex = FULL_DUPLEX; 3926 DEBUGOUT("Full Duplex\r\n"); 3927 } else { 3928 *duplex = HALF_DUPLEX; 3929 DEBUGOUT(" Half Duplex\r\n"); 3930 } 3931 } else { 3932 DEBUGOUT("1000 Mbs, Full Duplex\r\n"); 3933 *speed = SPEED_1000; 3934 *duplex = FULL_DUPLEX; 3935 } 3936 3937 /* IGP01 PHY may advertise full duplex operation after speed downgrade 3938 * even if it is operating at half duplex. Here we set the duplex 3939 * settings to match the duplex in the link partner's capabilities. 3940 */ 3941 if (hw->phy_type == e1000_phy_igp && hw->speed_downgraded) { 3942 ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_EXP, &phy_data); 3943 if (ret_val) 3944 return ret_val; 3945 3946 if (!(phy_data & NWAY_ER_LP_NWAY_CAPS)) 3947 *duplex = HALF_DUPLEX; 3948 else { 3949 ret_val = e1000_read_phy_reg(hw, 3950 PHY_LP_ABILITY, &phy_data); 3951 if (ret_val) 3952 return ret_val; 3953 if ((*speed == SPEED_100 && 3954 !(phy_data & NWAY_LPAR_100TX_FD_CAPS)) 3955 || (*speed == SPEED_10 3956 && !(phy_data & NWAY_LPAR_10T_FD_CAPS))) 3957 *duplex = HALF_DUPLEX; 3958 } 3959 } 3960 3961 if ((hw->mac_type == e1000_80003es2lan) && 3962 (hw->media_type == e1000_media_type_copper)) { 3963 if (*speed == SPEED_1000) 3964 ret_val = e1000_configure_kmrn_for_1000(hw); 3965 else 3966 ret_val = e1000_configure_kmrn_for_10_100(hw, *duplex); 3967 if (ret_val) 3968 return ret_val; 3969 } 3970 return E1000_SUCCESS; 3971 } 3972 3973 /****************************************************************************** 3974 * Blocks until autoneg completes or times out (~4.5 seconds) 3975 * 3976 * hw - Struct containing variables accessed by shared code 3977 ******************************************************************************/ 3978 static int 3979 e1000_wait_autoneg(struct e1000_hw *hw) 3980 { 3981 uint16_t i; 3982 uint16_t phy_data; 3983 3984 DEBUGFUNC(); 3985 DEBUGOUT("Waiting for Auto-Neg to complete.\n"); 3986 3987 /* We will wait for autoneg to complete or timeout to expire. */ 3988 for (i = PHY_AUTO_NEG_TIME; i > 0; i--) { 3989 /* Read the MII Status Register and wait for Auto-Neg 3990 * Complete bit to be set. 3991 */ 3992 if (e1000_read_phy_reg(hw, PHY_STATUS, &phy_data) < 0) { 3993 DEBUGOUT("PHY Read Error\n"); 3994 return -E1000_ERR_PHY; 3995 } 3996 if (e1000_read_phy_reg(hw, PHY_STATUS, &phy_data) < 0) { 3997 DEBUGOUT("PHY Read Error\n"); 3998 return -E1000_ERR_PHY; 3999 } 4000 if (phy_data & MII_SR_AUTONEG_COMPLETE) { 4001 DEBUGOUT("Auto-Neg complete.\n"); 4002 return 0; 4003 } 4004 mdelay(100); 4005 } 4006 DEBUGOUT("Auto-Neg timedout.\n"); 4007 return -E1000_ERR_TIMEOUT; 4008 } 4009 4010 /****************************************************************************** 4011 * Raises the Management Data Clock 4012 * 4013 * hw - Struct containing variables accessed by shared code 4014 * ctrl - Device control register's current value 4015 ******************************************************************************/ 4016 static void 4017 e1000_raise_mdi_clk(struct e1000_hw *hw, uint32_t * ctrl) 4018 { 4019 /* Raise the clock input to the Management Data Clock (by setting the MDC 4020 * bit), and then delay 2 microseconds. 4021 */ 4022 E1000_WRITE_REG(hw, CTRL, (*ctrl | E1000_CTRL_MDC)); 4023 E1000_WRITE_FLUSH(hw); 4024 udelay(2); 4025 } 4026 4027 /****************************************************************************** 4028 * Lowers the Management Data Clock 4029 * 4030 * hw - Struct containing variables accessed by shared code 4031 * ctrl - Device control register's current value 4032 ******************************************************************************/ 4033 static void 4034 e1000_lower_mdi_clk(struct e1000_hw *hw, uint32_t * ctrl) 4035 { 4036 /* Lower the clock input to the Management Data Clock (by clearing the MDC 4037 * bit), and then delay 2 microseconds. 4038 */ 4039 E1000_WRITE_REG(hw, CTRL, (*ctrl & ~E1000_CTRL_MDC)); 4040 E1000_WRITE_FLUSH(hw); 4041 udelay(2); 4042 } 4043 4044 /****************************************************************************** 4045 * Shifts data bits out to the PHY 4046 * 4047 * hw - Struct containing variables accessed by shared code 4048 * data - Data to send out to the PHY 4049 * count - Number of bits to shift out 4050 * 4051 * Bits are shifted out in MSB to LSB order. 4052 ******************************************************************************/ 4053 static void 4054 e1000_shift_out_mdi_bits(struct e1000_hw *hw, uint32_t data, uint16_t count) 4055 { 4056 uint32_t ctrl; 4057 uint32_t mask; 4058 4059 /* We need to shift "count" number of bits out to the PHY. So, the value 4060 * in the "data" parameter will be shifted out to the PHY one bit at a 4061 * time. In order to do this, "data" must be broken down into bits. 4062 */ 4063 mask = 0x01; 4064 mask <<= (count - 1); 4065 4066 ctrl = E1000_READ_REG(hw, CTRL); 4067 4068 /* Set MDIO_DIR and MDC_DIR direction bits to be used as output pins. */ 4069 ctrl |= (E1000_CTRL_MDIO_DIR | E1000_CTRL_MDC_DIR); 4070 4071 while (mask) { 4072 /* A "1" is shifted out to the PHY by setting the MDIO bit to "1" and 4073 * then raising and lowering the Management Data Clock. A "0" is 4074 * shifted out to the PHY by setting the MDIO bit to "0" and then 4075 * raising and lowering the clock. 4076 */ 4077 if (data & mask) 4078 ctrl |= E1000_CTRL_MDIO; 4079 else 4080 ctrl &= ~E1000_CTRL_MDIO; 4081 4082 E1000_WRITE_REG(hw, CTRL, ctrl); 4083 E1000_WRITE_FLUSH(hw); 4084 4085 udelay(2); 4086 4087 e1000_raise_mdi_clk(hw, &ctrl); 4088 e1000_lower_mdi_clk(hw, &ctrl); 4089 4090 mask = mask >> 1; 4091 } 4092 } 4093 4094 /****************************************************************************** 4095 * Shifts data bits in from the PHY 4096 * 4097 * hw - Struct containing variables accessed by shared code 4098 * 4099 * Bits are shifted in in MSB to LSB order. 4100 ******************************************************************************/ 4101 static uint16_t 4102 e1000_shift_in_mdi_bits(struct e1000_hw *hw) 4103 { 4104 uint32_t ctrl; 4105 uint16_t data = 0; 4106 uint8_t i; 4107 4108 /* In order to read a register from the PHY, we need to shift in a total 4109 * of 18 bits from the PHY. The first two bit (turnaround) times are used 4110 * to avoid contention on the MDIO pin when a read operation is performed. 4111 * These two bits are ignored by us and thrown away. Bits are "shifted in" 4112 * by raising the input to the Management Data Clock (setting the MDC bit), 4113 * and then reading the value of the MDIO bit. 4114 */ 4115 ctrl = E1000_READ_REG(hw, CTRL); 4116 4117 /* Clear MDIO_DIR (SWDPIO1) to indicate this bit is to be used as input. */ 4118 ctrl &= ~E1000_CTRL_MDIO_DIR; 4119 ctrl &= ~E1000_CTRL_MDIO; 4120 4121 E1000_WRITE_REG(hw, CTRL, ctrl); 4122 E1000_WRITE_FLUSH(hw); 4123 4124 /* Raise and Lower the clock before reading in the data. This accounts for 4125 * the turnaround bits. The first clock occurred when we clocked out the 4126 * last bit of the Register Address. 4127 */ 4128 e1000_raise_mdi_clk(hw, &ctrl); 4129 e1000_lower_mdi_clk(hw, &ctrl); 4130 4131 for (data = 0, i = 0; i < 16; i++) { 4132 data = data << 1; 4133 e1000_raise_mdi_clk(hw, &ctrl); 4134 ctrl = E1000_READ_REG(hw, CTRL); 4135 /* Check to see if we shifted in a "1". */ 4136 if (ctrl & E1000_CTRL_MDIO) 4137 data |= 1; 4138 e1000_lower_mdi_clk(hw, &ctrl); 4139 } 4140 4141 e1000_raise_mdi_clk(hw, &ctrl); 4142 e1000_lower_mdi_clk(hw, &ctrl); 4143 4144 return data; 4145 } 4146 4147 /***************************************************************************** 4148 * Reads the value from a PHY register 4149 * 4150 * hw - Struct containing variables accessed by shared code 4151 * reg_addr - address of the PHY register to read 4152 ******************************************************************************/ 4153 static int 4154 e1000_read_phy_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t * phy_data) 4155 { 4156 uint32_t i; 4157 uint32_t mdic = 0; 4158 const uint32_t phy_addr = 1; 4159 4160 if (reg_addr > MAX_PHY_REG_ADDRESS) { 4161 DEBUGOUT("PHY Address %d is out of range\n", reg_addr); 4162 return -E1000_ERR_PARAM; 4163 } 4164 4165 if (hw->mac_type > e1000_82543) { 4166 /* Set up Op-code, Phy Address, and register address in the MDI 4167 * Control register. The MAC will take care of interfacing with the 4168 * PHY to retrieve the desired data. 4169 */ 4170 mdic = ((reg_addr << E1000_MDIC_REG_SHIFT) | 4171 (phy_addr << E1000_MDIC_PHY_SHIFT) | 4172 (E1000_MDIC_OP_READ)); 4173 4174 E1000_WRITE_REG(hw, MDIC, mdic); 4175 4176 /* Poll the ready bit to see if the MDI read completed */ 4177 for (i = 0; i < 64; i++) { 4178 udelay(10); 4179 mdic = E1000_READ_REG(hw, MDIC); 4180 if (mdic & E1000_MDIC_READY) 4181 break; 4182 } 4183 if (!(mdic & E1000_MDIC_READY)) { 4184 DEBUGOUT("MDI Read did not complete\n"); 4185 return -E1000_ERR_PHY; 4186 } 4187 if (mdic & E1000_MDIC_ERROR) { 4188 DEBUGOUT("MDI Error\n"); 4189 return -E1000_ERR_PHY; 4190 } 4191 *phy_data = (uint16_t) mdic; 4192 } else { 4193 /* We must first send a preamble through the MDIO pin to signal the 4194 * beginning of an MII instruction. This is done by sending 32 4195 * consecutive "1" bits. 4196 */ 4197 e1000_shift_out_mdi_bits(hw, PHY_PREAMBLE, PHY_PREAMBLE_SIZE); 4198 4199 /* Now combine the next few fields that are required for a read 4200 * operation. We use this method instead of calling the 4201 * e1000_shift_out_mdi_bits routine five different times. The format of 4202 * a MII read instruction consists of a shift out of 14 bits and is 4203 * defined as follows: 4204 * <Preamble><SOF><Op Code><Phy Addr><Reg Addr> 4205 * followed by a shift in of 18 bits. This first two bits shifted in 4206 * are TurnAround bits used to avoid contention on the MDIO pin when a 4207 * READ operation is performed. These two bits are thrown away 4208 * followed by a shift in of 16 bits which contains the desired data. 4209 */ 4210 mdic = ((reg_addr) | (phy_addr << 5) | 4211 (PHY_OP_READ << 10) | (PHY_SOF << 12)); 4212 4213 e1000_shift_out_mdi_bits(hw, mdic, 14); 4214 4215 /* Now that we've shifted out the read command to the MII, we need to 4216 * "shift in" the 16-bit value (18 total bits) of the requested PHY 4217 * register address. 4218 */ 4219 *phy_data = e1000_shift_in_mdi_bits(hw); 4220 } 4221 return 0; 4222 } 4223 4224 /****************************************************************************** 4225 * Writes a value to a PHY register 4226 * 4227 * hw - Struct containing variables accessed by shared code 4228 * reg_addr - address of the PHY register to write 4229 * data - data to write to the PHY 4230 ******************************************************************************/ 4231 static int 4232 e1000_write_phy_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t phy_data) 4233 { 4234 uint32_t i; 4235 uint32_t mdic = 0; 4236 const uint32_t phy_addr = 1; 4237 4238 if (reg_addr > MAX_PHY_REG_ADDRESS) { 4239 DEBUGOUT("PHY Address %d is out of range\n", reg_addr); 4240 return -E1000_ERR_PARAM; 4241 } 4242 4243 if (hw->mac_type > e1000_82543) { 4244 /* Set up Op-code, Phy Address, register address, and data intended 4245 * for the PHY register in the MDI Control register. The MAC will take 4246 * care of interfacing with the PHY to send the desired data. 4247 */ 4248 mdic = (((uint32_t) phy_data) | 4249 (reg_addr << E1000_MDIC_REG_SHIFT) | 4250 (phy_addr << E1000_MDIC_PHY_SHIFT) | 4251 (E1000_MDIC_OP_WRITE)); 4252 4253 E1000_WRITE_REG(hw, MDIC, mdic); 4254 4255 /* Poll the ready bit to see if the MDI read completed */ 4256 for (i = 0; i < 64; i++) { 4257 udelay(10); 4258 mdic = E1000_READ_REG(hw, MDIC); 4259 if (mdic & E1000_MDIC_READY) 4260 break; 4261 } 4262 if (!(mdic & E1000_MDIC_READY)) { 4263 DEBUGOUT("MDI Write did not complete\n"); 4264 return -E1000_ERR_PHY; 4265 } 4266 } else { 4267 /* We'll need to use the SW defined pins to shift the write command 4268 * out to the PHY. We first send a preamble to the PHY to signal the 4269 * beginning of the MII instruction. This is done by sending 32 4270 * consecutive "1" bits. 4271 */ 4272 e1000_shift_out_mdi_bits(hw, PHY_PREAMBLE, PHY_PREAMBLE_SIZE); 4273 4274 /* Now combine the remaining required fields that will indicate a 4275 * write operation. We use this method instead of calling the 4276 * e1000_shift_out_mdi_bits routine for each field in the command. The 4277 * format of a MII write instruction is as follows: 4278 * <Preamble><SOF><Op Code><Phy Addr><Reg Addr><Turnaround><Data>. 4279 */ 4280 mdic = ((PHY_TURNAROUND) | (reg_addr << 2) | (phy_addr << 7) | 4281 (PHY_OP_WRITE << 12) | (PHY_SOF << 14)); 4282 mdic <<= 16; 4283 mdic |= (uint32_t) phy_data; 4284 4285 e1000_shift_out_mdi_bits(hw, mdic, 32); 4286 } 4287 return 0; 4288 } 4289 4290 /****************************************************************************** 4291 * Checks if PHY reset is blocked due to SOL/IDER session, for example. 4292 * Returning E1000_BLK_PHY_RESET isn't necessarily an error. But it's up to 4293 * the caller to figure out how to deal with it. 4294 * 4295 * hw - Struct containing variables accessed by shared code 4296 * 4297 * returns: - E1000_BLK_PHY_RESET 4298 * E1000_SUCCESS 4299 * 4300 *****************************************************************************/ 4301 int32_t 4302 e1000_check_phy_reset_block(struct e1000_hw *hw) 4303 { 4304 uint32_t manc = 0; 4305 uint32_t fwsm = 0; 4306 4307 if (hw->mac_type == e1000_ich8lan) { 4308 fwsm = E1000_READ_REG(hw, FWSM); 4309 return (fwsm & E1000_FWSM_RSPCIPHY) ? E1000_SUCCESS 4310 : E1000_BLK_PHY_RESET; 4311 } 4312 4313 if (hw->mac_type > e1000_82547_rev_2) 4314 manc = E1000_READ_REG(hw, MANC); 4315 return (manc & E1000_MANC_BLK_PHY_RST_ON_IDE) ? 4316 E1000_BLK_PHY_RESET : E1000_SUCCESS; 4317 } 4318 4319 /*************************************************************************** 4320 * Checks if the PHY configuration is done 4321 * 4322 * hw: Struct containing variables accessed by shared code 4323 * 4324 * returns: - E1000_ERR_RESET if fail to reset MAC 4325 * E1000_SUCCESS at any other case. 4326 * 4327 ***************************************************************************/ 4328 static int32_t 4329 e1000_get_phy_cfg_done(struct e1000_hw *hw) 4330 { 4331 int32_t timeout = PHY_CFG_TIMEOUT; 4332 uint32_t cfg_mask = E1000_EEPROM_CFG_DONE; 4333 4334 DEBUGFUNC(); 4335 4336 switch (hw->mac_type) { 4337 default: 4338 mdelay(10); 4339 break; 4340 4341 case e1000_80003es2lan: 4342 /* Separate *_CFG_DONE_* bit for each port */ 4343 if (e1000_is_second_port(hw)) 4344 cfg_mask = E1000_EEPROM_CFG_DONE_PORT_1; 4345 /* Fall Through */ 4346 4347 case e1000_82571: 4348 case e1000_82572: 4349 case e1000_igb: 4350 while (timeout) { 4351 if (hw->mac_type == e1000_igb) { 4352 if (E1000_READ_REG(hw, I210_EEMNGCTL) & cfg_mask) 4353 break; 4354 } else { 4355 if (E1000_READ_REG(hw, EEMNGCTL) & cfg_mask) 4356 break; 4357 } 4358 mdelay(1); 4359 timeout--; 4360 } 4361 if (!timeout) { 4362 DEBUGOUT("MNG configuration cycle has not " 4363 "completed.\n"); 4364 return -E1000_ERR_RESET; 4365 } 4366 break; 4367 } 4368 4369 return E1000_SUCCESS; 4370 } 4371 4372 /****************************************************************************** 4373 * Returns the PHY to the power-on reset state 4374 * 4375 * hw - Struct containing variables accessed by shared code 4376 ******************************************************************************/ 4377 int32_t 4378 e1000_phy_hw_reset(struct e1000_hw *hw) 4379 { 4380 uint16_t swfw = E1000_SWFW_PHY0_SM; 4381 uint32_t ctrl, ctrl_ext; 4382 uint32_t led_ctrl; 4383 int32_t ret_val; 4384 4385 DEBUGFUNC(); 4386 4387 /* In the case of the phy reset being blocked, it's not an error, we 4388 * simply return success without performing the reset. */ 4389 ret_val = e1000_check_phy_reset_block(hw); 4390 if (ret_val) 4391 return E1000_SUCCESS; 4392 4393 DEBUGOUT("Resetting Phy...\n"); 4394 4395 if (hw->mac_type > e1000_82543) { 4396 if (e1000_is_second_port(hw)) 4397 swfw = E1000_SWFW_PHY1_SM; 4398 4399 if (e1000_swfw_sync_acquire(hw, swfw)) { 4400 DEBUGOUT("Unable to acquire swfw sync\n"); 4401 return -E1000_ERR_SWFW_SYNC; 4402 } 4403 4404 /* Read the device control register and assert the E1000_CTRL_PHY_RST 4405 * bit. Then, take it out of reset. 4406 */ 4407 ctrl = E1000_READ_REG(hw, CTRL); 4408 E1000_WRITE_REG(hw, CTRL, ctrl | E1000_CTRL_PHY_RST); 4409 E1000_WRITE_FLUSH(hw); 4410 4411 if (hw->mac_type < e1000_82571) 4412 udelay(10); 4413 else 4414 udelay(100); 4415 4416 E1000_WRITE_REG(hw, CTRL, ctrl); 4417 E1000_WRITE_FLUSH(hw); 4418 4419 if (hw->mac_type >= e1000_82571) 4420 mdelay(10); 4421 4422 } else { 4423 /* Read the Extended Device Control Register, assert the PHY_RESET_DIR 4424 * bit to put the PHY into reset. Then, take it out of reset. 4425 */ 4426 ctrl_ext = E1000_READ_REG(hw, CTRL_EXT); 4427 ctrl_ext |= E1000_CTRL_EXT_SDP4_DIR; 4428 ctrl_ext &= ~E1000_CTRL_EXT_SDP4_DATA; 4429 E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext); 4430 E1000_WRITE_FLUSH(hw); 4431 mdelay(10); 4432 ctrl_ext |= E1000_CTRL_EXT_SDP4_DATA; 4433 E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext); 4434 E1000_WRITE_FLUSH(hw); 4435 } 4436 udelay(150); 4437 4438 if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) { 4439 /* Configure activity LED after PHY reset */ 4440 led_ctrl = E1000_READ_REG(hw, LEDCTL); 4441 led_ctrl &= IGP_ACTIVITY_LED_MASK; 4442 led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE); 4443 E1000_WRITE_REG(hw, LEDCTL, led_ctrl); 4444 } 4445 4446 e1000_swfw_sync_release(hw, swfw); 4447 4448 /* Wait for FW to finish PHY configuration. */ 4449 ret_val = e1000_get_phy_cfg_done(hw); 4450 if (ret_val != E1000_SUCCESS) 4451 return ret_val; 4452 4453 return ret_val; 4454 } 4455 4456 /****************************************************************************** 4457 * IGP phy init script - initializes the GbE PHY 4458 * 4459 * hw - Struct containing variables accessed by shared code 4460 *****************************************************************************/ 4461 static void 4462 e1000_phy_init_script(struct e1000_hw *hw) 4463 { 4464 uint32_t ret_val; 4465 uint16_t phy_saved_data; 4466 DEBUGFUNC(); 4467 4468 if (hw->phy_init_script) { 4469 mdelay(20); 4470 4471 /* Save off the current value of register 0x2F5B to be 4472 * restored at the end of this routine. */ 4473 ret_val = e1000_read_phy_reg(hw, 0x2F5B, &phy_saved_data); 4474 4475 /* Disabled the PHY transmitter */ 4476 e1000_write_phy_reg(hw, 0x2F5B, 0x0003); 4477 4478 mdelay(20); 4479 4480 e1000_write_phy_reg(hw, 0x0000, 0x0140); 4481 4482 mdelay(5); 4483 4484 switch (hw->mac_type) { 4485 case e1000_82541: 4486 case e1000_82547: 4487 e1000_write_phy_reg(hw, 0x1F95, 0x0001); 4488 4489 e1000_write_phy_reg(hw, 0x1F71, 0xBD21); 4490 4491 e1000_write_phy_reg(hw, 0x1F79, 0x0018); 4492 4493 e1000_write_phy_reg(hw, 0x1F30, 0x1600); 4494 4495 e1000_write_phy_reg(hw, 0x1F31, 0x0014); 4496 4497 e1000_write_phy_reg(hw, 0x1F32, 0x161C); 4498 4499 e1000_write_phy_reg(hw, 0x1F94, 0x0003); 4500 4501 e1000_write_phy_reg(hw, 0x1F96, 0x003F); 4502 4503 e1000_write_phy_reg(hw, 0x2010, 0x0008); 4504 break; 4505 4506 case e1000_82541_rev_2: 4507 case e1000_82547_rev_2: 4508 e1000_write_phy_reg(hw, 0x1F73, 0x0099); 4509 break; 4510 default: 4511 break; 4512 } 4513 4514 e1000_write_phy_reg(hw, 0x0000, 0x3300); 4515 4516 mdelay(20); 4517 4518 /* Now enable the transmitter */ 4519 if (!ret_val) 4520 e1000_write_phy_reg(hw, 0x2F5B, phy_saved_data); 4521 4522 if (hw->mac_type == e1000_82547) { 4523 uint16_t fused, fine, coarse; 4524 4525 /* Move to analog registers page */ 4526 e1000_read_phy_reg(hw, 4527 IGP01E1000_ANALOG_SPARE_FUSE_STATUS, &fused); 4528 4529 if (!(fused & IGP01E1000_ANALOG_SPARE_FUSE_ENABLED)) { 4530 e1000_read_phy_reg(hw, 4531 IGP01E1000_ANALOG_FUSE_STATUS, &fused); 4532 4533 fine = fused & IGP01E1000_ANALOG_FUSE_FINE_MASK; 4534 coarse = fused 4535 & IGP01E1000_ANALOG_FUSE_COARSE_MASK; 4536 4537 if (coarse > 4538 IGP01E1000_ANALOG_FUSE_COARSE_THRESH) { 4539 coarse -= 4540 IGP01E1000_ANALOG_FUSE_COARSE_10; 4541 fine -= IGP01E1000_ANALOG_FUSE_FINE_1; 4542 } else if (coarse 4543 == IGP01E1000_ANALOG_FUSE_COARSE_THRESH) 4544 fine -= IGP01E1000_ANALOG_FUSE_FINE_10; 4545 4546 fused = (fused 4547 & IGP01E1000_ANALOG_FUSE_POLY_MASK) | 4548 (fine 4549 & IGP01E1000_ANALOG_FUSE_FINE_MASK) | 4550 (coarse 4551 & IGP01E1000_ANALOG_FUSE_COARSE_MASK); 4552 4553 e1000_write_phy_reg(hw, 4554 IGP01E1000_ANALOG_FUSE_CONTROL, fused); 4555 e1000_write_phy_reg(hw, 4556 IGP01E1000_ANALOG_FUSE_BYPASS, 4557 IGP01E1000_ANALOG_FUSE_ENABLE_SW_CONTROL); 4558 } 4559 } 4560 } 4561 } 4562 4563 /****************************************************************************** 4564 * Resets the PHY 4565 * 4566 * hw - Struct containing variables accessed by shared code 4567 * 4568 * Sets bit 15 of the MII Control register 4569 ******************************************************************************/ 4570 int32_t 4571 e1000_phy_reset(struct e1000_hw *hw) 4572 { 4573 int32_t ret_val; 4574 uint16_t phy_data; 4575 4576 DEBUGFUNC(); 4577 4578 /* In the case of the phy reset being blocked, it's not an error, we 4579 * simply return success without performing the reset. */ 4580 ret_val = e1000_check_phy_reset_block(hw); 4581 if (ret_val) 4582 return E1000_SUCCESS; 4583 4584 switch (hw->phy_type) { 4585 case e1000_phy_igp: 4586 case e1000_phy_igp_2: 4587 case e1000_phy_igp_3: 4588 case e1000_phy_ife: 4589 case e1000_phy_igb: 4590 ret_val = e1000_phy_hw_reset(hw); 4591 if (ret_val) 4592 return ret_val; 4593 break; 4594 default: 4595 ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data); 4596 if (ret_val) 4597 return ret_val; 4598 4599 phy_data |= MII_CR_RESET; 4600 ret_val = e1000_write_phy_reg(hw, PHY_CTRL, phy_data); 4601 if (ret_val) 4602 return ret_val; 4603 4604 udelay(1); 4605 break; 4606 } 4607 4608 if (hw->phy_type == e1000_phy_igp || hw->phy_type == e1000_phy_igp_2) 4609 e1000_phy_init_script(hw); 4610 4611 return E1000_SUCCESS; 4612 } 4613 4614 static int e1000_set_phy_type (struct e1000_hw *hw) 4615 { 4616 DEBUGFUNC (); 4617 4618 if (hw->mac_type == e1000_undefined) 4619 return -E1000_ERR_PHY_TYPE; 4620 4621 switch (hw->phy_id) { 4622 case M88E1000_E_PHY_ID: 4623 case M88E1000_I_PHY_ID: 4624 case M88E1011_I_PHY_ID: 4625 case M88E1111_I_PHY_ID: 4626 hw->phy_type = e1000_phy_m88; 4627 break; 4628 case IGP01E1000_I_PHY_ID: 4629 if (hw->mac_type == e1000_82541 || 4630 hw->mac_type == e1000_82541_rev_2 || 4631 hw->mac_type == e1000_82547 || 4632 hw->mac_type == e1000_82547_rev_2) { 4633 hw->phy_type = e1000_phy_igp; 4634 break; 4635 } 4636 case IGP03E1000_E_PHY_ID: 4637 hw->phy_type = e1000_phy_igp_3; 4638 break; 4639 case IFE_E_PHY_ID: 4640 case IFE_PLUS_E_PHY_ID: 4641 case IFE_C_E_PHY_ID: 4642 hw->phy_type = e1000_phy_ife; 4643 break; 4644 case GG82563_E_PHY_ID: 4645 if (hw->mac_type == e1000_80003es2lan) { 4646 hw->phy_type = e1000_phy_gg82563; 4647 break; 4648 } 4649 case BME1000_E_PHY_ID: 4650 hw->phy_type = e1000_phy_bm; 4651 break; 4652 case I210_I_PHY_ID: 4653 hw->phy_type = e1000_phy_igb; 4654 break; 4655 /* Fall Through */ 4656 default: 4657 /* Should never have loaded on this device */ 4658 hw->phy_type = e1000_phy_undefined; 4659 return -E1000_ERR_PHY_TYPE; 4660 } 4661 4662 return E1000_SUCCESS; 4663 } 4664 4665 /****************************************************************************** 4666 * Probes the expected PHY address for known PHY IDs 4667 * 4668 * hw - Struct containing variables accessed by shared code 4669 ******************************************************************************/ 4670 static int32_t 4671 e1000_detect_gig_phy(struct e1000_hw *hw) 4672 { 4673 int32_t phy_init_status, ret_val; 4674 uint16_t phy_id_high, phy_id_low; 4675 bool match = false; 4676 4677 DEBUGFUNC(); 4678 4679 /* The 82571 firmware may still be configuring the PHY. In this 4680 * case, we cannot access the PHY until the configuration is done. So 4681 * we explicitly set the PHY values. */ 4682 if (hw->mac_type == e1000_82571 || 4683 hw->mac_type == e1000_82572) { 4684 hw->phy_id = IGP01E1000_I_PHY_ID; 4685 hw->phy_type = e1000_phy_igp_2; 4686 return E1000_SUCCESS; 4687 } 4688 4689 /* ESB-2 PHY reads require e1000_phy_gg82563 to be set because of a 4690 * work- around that forces PHY page 0 to be set or the reads fail. 4691 * The rest of the code in this routine uses e1000_read_phy_reg to 4692 * read the PHY ID. So for ESB-2 we need to have this set so our 4693 * reads won't fail. If the attached PHY is not a e1000_phy_gg82563, 4694 * the routines below will figure this out as well. */ 4695 if (hw->mac_type == e1000_80003es2lan) 4696 hw->phy_type = e1000_phy_gg82563; 4697 4698 /* Read the PHY ID Registers to identify which PHY is onboard. */ 4699 ret_val = e1000_read_phy_reg(hw, PHY_ID1, &phy_id_high); 4700 if (ret_val) 4701 return ret_val; 4702 4703 hw->phy_id = (uint32_t) (phy_id_high << 16); 4704 udelay(20); 4705 ret_val = e1000_read_phy_reg(hw, PHY_ID2, &phy_id_low); 4706 if (ret_val) 4707 return ret_val; 4708 4709 hw->phy_id |= (uint32_t) (phy_id_low & PHY_REVISION_MASK); 4710 hw->phy_revision = (uint32_t) phy_id_low & ~PHY_REVISION_MASK; 4711 4712 switch (hw->mac_type) { 4713 case e1000_82543: 4714 if (hw->phy_id == M88E1000_E_PHY_ID) 4715 match = true; 4716 break; 4717 case e1000_82544: 4718 if (hw->phy_id == M88E1000_I_PHY_ID) 4719 match = true; 4720 break; 4721 case e1000_82540: 4722 case e1000_82545: 4723 case e1000_82545_rev_3: 4724 case e1000_82546: 4725 case e1000_82546_rev_3: 4726 if (hw->phy_id == M88E1011_I_PHY_ID) 4727 match = true; 4728 break; 4729 case e1000_82541: 4730 case e1000_82541_rev_2: 4731 case e1000_82547: 4732 case e1000_82547_rev_2: 4733 if(hw->phy_id == IGP01E1000_I_PHY_ID) 4734 match = true; 4735 4736 break; 4737 case e1000_82573: 4738 if (hw->phy_id == M88E1111_I_PHY_ID) 4739 match = true; 4740 break; 4741 case e1000_82574: 4742 if (hw->phy_id == BME1000_E_PHY_ID) 4743 match = true; 4744 break; 4745 case e1000_80003es2lan: 4746 if (hw->phy_id == GG82563_E_PHY_ID) 4747 match = true; 4748 break; 4749 case e1000_ich8lan: 4750 if (hw->phy_id == IGP03E1000_E_PHY_ID) 4751 match = true; 4752 if (hw->phy_id == IFE_E_PHY_ID) 4753 match = true; 4754 if (hw->phy_id == IFE_PLUS_E_PHY_ID) 4755 match = true; 4756 if (hw->phy_id == IFE_C_E_PHY_ID) 4757 match = true; 4758 break; 4759 case e1000_igb: 4760 if (hw->phy_id == I210_I_PHY_ID) 4761 match = true; 4762 break; 4763 default: 4764 DEBUGOUT("Invalid MAC type %d\n", hw->mac_type); 4765 return -E1000_ERR_CONFIG; 4766 } 4767 4768 phy_init_status = e1000_set_phy_type(hw); 4769 4770 if ((match) && (phy_init_status == E1000_SUCCESS)) { 4771 DEBUGOUT("PHY ID 0x%X detected\n", hw->phy_id); 4772 return 0; 4773 } 4774 DEBUGOUT("Invalid PHY ID 0x%X\n", hw->phy_id); 4775 return -E1000_ERR_PHY; 4776 } 4777 4778 /***************************************************************************** 4779 * Set media type and TBI compatibility. 4780 * 4781 * hw - Struct containing variables accessed by shared code 4782 * **************************************************************************/ 4783 void 4784 e1000_set_media_type(struct e1000_hw *hw) 4785 { 4786 uint32_t status; 4787 4788 DEBUGFUNC(); 4789 4790 if (hw->mac_type != e1000_82543) { 4791 /* tbi_compatibility is only valid on 82543 */ 4792 hw->tbi_compatibility_en = false; 4793 } 4794 4795 switch (hw->device_id) { 4796 case E1000_DEV_ID_82545GM_SERDES: 4797 case E1000_DEV_ID_82546GB_SERDES: 4798 case E1000_DEV_ID_82571EB_SERDES: 4799 case E1000_DEV_ID_82571EB_SERDES_DUAL: 4800 case E1000_DEV_ID_82571EB_SERDES_QUAD: 4801 case E1000_DEV_ID_82572EI_SERDES: 4802 case E1000_DEV_ID_80003ES2LAN_SERDES_DPT: 4803 hw->media_type = e1000_media_type_internal_serdes; 4804 break; 4805 default: 4806 switch (hw->mac_type) { 4807 case e1000_82542_rev2_0: 4808 case e1000_82542_rev2_1: 4809 hw->media_type = e1000_media_type_fiber; 4810 break; 4811 case e1000_ich8lan: 4812 case e1000_82573: 4813 case e1000_82574: 4814 case e1000_igb: 4815 /* The STATUS_TBIMODE bit is reserved or reused 4816 * for the this device. 4817 */ 4818 hw->media_type = e1000_media_type_copper; 4819 break; 4820 default: 4821 status = E1000_READ_REG(hw, STATUS); 4822 if (status & E1000_STATUS_TBIMODE) { 4823 hw->media_type = e1000_media_type_fiber; 4824 /* tbi_compatibility not valid on fiber */ 4825 hw->tbi_compatibility_en = false; 4826 } else { 4827 hw->media_type = e1000_media_type_copper; 4828 } 4829 break; 4830 } 4831 } 4832 } 4833 4834 /** 4835 * e1000_sw_init - Initialize general software structures (struct e1000_adapter) 4836 * 4837 * e1000_sw_init initializes the Adapter private data structure. 4838 * Fields are initialized based on PCI device information and 4839 * OS network device settings (MTU size). 4840 **/ 4841 4842 static int 4843 e1000_sw_init(struct e1000_hw *hw) 4844 { 4845 int result; 4846 4847 /* PCI config space info */ 4848 #ifdef CONFIG_DM_ETH 4849 dm_pci_read_config16(hw->pdev, PCI_VENDOR_ID, &hw->vendor_id); 4850 dm_pci_read_config16(hw->pdev, PCI_DEVICE_ID, &hw->device_id); 4851 dm_pci_read_config16(hw->pdev, PCI_SUBSYSTEM_VENDOR_ID, 4852 &hw->subsystem_vendor_id); 4853 dm_pci_read_config16(hw->pdev, PCI_SUBSYSTEM_ID, &hw->subsystem_id); 4854 4855 dm_pci_read_config8(hw->pdev, PCI_REVISION_ID, &hw->revision_id); 4856 dm_pci_read_config16(hw->pdev, PCI_COMMAND, &hw->pci_cmd_word); 4857 #else 4858 pci_read_config_word(hw->pdev, PCI_VENDOR_ID, &hw->vendor_id); 4859 pci_read_config_word(hw->pdev, PCI_DEVICE_ID, &hw->device_id); 4860 pci_read_config_word(hw->pdev, PCI_SUBSYSTEM_VENDOR_ID, 4861 &hw->subsystem_vendor_id); 4862 pci_read_config_word(hw->pdev, PCI_SUBSYSTEM_ID, &hw->subsystem_id); 4863 4864 pci_read_config_byte(hw->pdev, PCI_REVISION_ID, &hw->revision_id); 4865 pci_read_config_word(hw->pdev, PCI_COMMAND, &hw->pci_cmd_word); 4866 #endif 4867 4868 /* identify the MAC */ 4869 result = e1000_set_mac_type(hw); 4870 if (result) { 4871 E1000_ERR(hw, "Unknown MAC Type\n"); 4872 return result; 4873 } 4874 4875 switch (hw->mac_type) { 4876 default: 4877 break; 4878 case e1000_82541: 4879 case e1000_82547: 4880 case e1000_82541_rev_2: 4881 case e1000_82547_rev_2: 4882 hw->phy_init_script = 1; 4883 break; 4884 } 4885 4886 /* flow control settings */ 4887 hw->fc_high_water = E1000_FC_HIGH_THRESH; 4888 hw->fc_low_water = E1000_FC_LOW_THRESH; 4889 hw->fc_pause_time = E1000_FC_PAUSE_TIME; 4890 hw->fc_send_xon = 1; 4891 4892 /* Media type - copper or fiber */ 4893 hw->tbi_compatibility_en = true; 4894 e1000_set_media_type(hw); 4895 4896 if (hw->mac_type >= e1000_82543) { 4897 uint32_t status = E1000_READ_REG(hw, STATUS); 4898 4899 if (status & E1000_STATUS_TBIMODE) { 4900 DEBUGOUT("fiber interface\n"); 4901 hw->media_type = e1000_media_type_fiber; 4902 } else { 4903 DEBUGOUT("copper interface\n"); 4904 hw->media_type = e1000_media_type_copper; 4905 } 4906 } else { 4907 hw->media_type = e1000_media_type_fiber; 4908 } 4909 4910 hw->wait_autoneg_complete = true; 4911 if (hw->mac_type < e1000_82543) 4912 hw->report_tx_early = 0; 4913 else 4914 hw->report_tx_early = 1; 4915 4916 return E1000_SUCCESS; 4917 } 4918 4919 void 4920 fill_rx(struct e1000_hw *hw) 4921 { 4922 struct e1000_rx_desc *rd; 4923 unsigned long flush_start, flush_end; 4924 4925 rx_last = rx_tail; 4926 rd = rx_base + rx_tail; 4927 rx_tail = (rx_tail + 1) % 8; 4928 memset(rd, 0, 16); 4929 rd->buffer_addr = cpu_to_le64((unsigned long)packet); 4930 4931 /* 4932 * Make sure there are no stale data in WB over this area, which 4933 * might get written into the memory while the e1000 also writes 4934 * into the same memory area. 4935 */ 4936 invalidate_dcache_range((unsigned long)packet, 4937 (unsigned long)packet + 4096); 4938 /* Dump the DMA descriptor into RAM. */ 4939 flush_start = ((unsigned long)rd) & ~(ARCH_DMA_MINALIGN - 1); 4940 flush_end = flush_start + roundup(sizeof(*rd), ARCH_DMA_MINALIGN); 4941 flush_dcache_range(flush_start, flush_end); 4942 4943 E1000_WRITE_REG(hw, RDT, rx_tail); 4944 } 4945 4946 /** 4947 * e1000_configure_tx - Configure 8254x Transmit Unit after Reset 4948 * @adapter: board private structure 4949 * 4950 * Configure the Tx unit of the MAC after a reset. 4951 **/ 4952 4953 static void 4954 e1000_configure_tx(struct e1000_hw *hw) 4955 { 4956 unsigned long tctl; 4957 unsigned long tipg, tarc; 4958 uint32_t ipgr1, ipgr2; 4959 4960 E1000_WRITE_REG(hw, TDBAL, lower_32_bits((unsigned long)tx_base)); 4961 E1000_WRITE_REG(hw, TDBAH, upper_32_bits((unsigned long)tx_base)); 4962 4963 E1000_WRITE_REG(hw, TDLEN, 128); 4964 4965 /* Setup the HW Tx Head and Tail descriptor pointers */ 4966 E1000_WRITE_REG(hw, TDH, 0); 4967 E1000_WRITE_REG(hw, TDT, 0); 4968 tx_tail = 0; 4969 4970 /* Set the default values for the Tx Inter Packet Gap timer */ 4971 if (hw->mac_type <= e1000_82547_rev_2 && 4972 (hw->media_type == e1000_media_type_fiber || 4973 hw->media_type == e1000_media_type_internal_serdes)) 4974 tipg = DEFAULT_82543_TIPG_IPGT_FIBER; 4975 else 4976 tipg = DEFAULT_82543_TIPG_IPGT_COPPER; 4977 4978 /* Set the default values for the Tx Inter Packet Gap timer */ 4979 switch (hw->mac_type) { 4980 case e1000_82542_rev2_0: 4981 case e1000_82542_rev2_1: 4982 tipg = DEFAULT_82542_TIPG_IPGT; 4983 ipgr1 = DEFAULT_82542_TIPG_IPGR1; 4984 ipgr2 = DEFAULT_82542_TIPG_IPGR2; 4985 break; 4986 case e1000_80003es2lan: 4987 ipgr1 = DEFAULT_82543_TIPG_IPGR1; 4988 ipgr2 = DEFAULT_80003ES2LAN_TIPG_IPGR2; 4989 break; 4990 default: 4991 ipgr1 = DEFAULT_82543_TIPG_IPGR1; 4992 ipgr2 = DEFAULT_82543_TIPG_IPGR2; 4993 break; 4994 } 4995 tipg |= ipgr1 << E1000_TIPG_IPGR1_SHIFT; 4996 tipg |= ipgr2 << E1000_TIPG_IPGR2_SHIFT; 4997 E1000_WRITE_REG(hw, TIPG, tipg); 4998 /* Program the Transmit Control Register */ 4999 tctl = E1000_READ_REG(hw, TCTL); 5000 tctl &= ~E1000_TCTL_CT; 5001 tctl |= E1000_TCTL_EN | E1000_TCTL_PSP | 5002 (E1000_COLLISION_THRESHOLD << E1000_CT_SHIFT); 5003 5004 if (hw->mac_type == e1000_82571 || hw->mac_type == e1000_82572) { 5005 tarc = E1000_READ_REG(hw, TARC0); 5006 /* set the speed mode bit, we'll clear it if we're not at 5007 * gigabit link later */ 5008 /* git bit can be set to 1*/ 5009 } else if (hw->mac_type == e1000_80003es2lan) { 5010 tarc = E1000_READ_REG(hw, TARC0); 5011 tarc |= 1; 5012 E1000_WRITE_REG(hw, TARC0, tarc); 5013 tarc = E1000_READ_REG(hw, TARC1); 5014 tarc |= 1; 5015 E1000_WRITE_REG(hw, TARC1, tarc); 5016 } 5017 5018 5019 e1000_config_collision_dist(hw); 5020 /* Setup Transmit Descriptor Settings for eop descriptor */ 5021 hw->txd_cmd = E1000_TXD_CMD_EOP | E1000_TXD_CMD_IFCS; 5022 5023 /* Need to set up RS bit */ 5024 if (hw->mac_type < e1000_82543) 5025 hw->txd_cmd |= E1000_TXD_CMD_RPS; 5026 else 5027 hw->txd_cmd |= E1000_TXD_CMD_RS; 5028 5029 5030 if (hw->mac_type == e1000_igb) { 5031 E1000_WRITE_REG(hw, TCTL_EXT, 0x42 << 10); 5032 5033 uint32_t reg_txdctl = E1000_READ_REG(hw, TXDCTL); 5034 reg_txdctl |= 1 << 25; 5035 E1000_WRITE_REG(hw, TXDCTL, reg_txdctl); 5036 mdelay(20); 5037 } 5038 5039 5040 5041 E1000_WRITE_REG(hw, TCTL, tctl); 5042 5043 5044 } 5045 5046 /** 5047 * e1000_setup_rctl - configure the receive control register 5048 * @adapter: Board private structure 5049 **/ 5050 static void 5051 e1000_setup_rctl(struct e1000_hw *hw) 5052 { 5053 uint32_t rctl; 5054 5055 rctl = E1000_READ_REG(hw, RCTL); 5056 5057 rctl &= ~(3 << E1000_RCTL_MO_SHIFT); 5058 5059 rctl |= E1000_RCTL_EN | E1000_RCTL_BAM | E1000_RCTL_LBM_NO 5060 | E1000_RCTL_RDMTS_HALF; /* | 5061 (hw.mc_filter_type << E1000_RCTL_MO_SHIFT); */ 5062 5063 if (hw->tbi_compatibility_on == 1) 5064 rctl |= E1000_RCTL_SBP; 5065 else 5066 rctl &= ~E1000_RCTL_SBP; 5067 5068 rctl &= ~(E1000_RCTL_SZ_4096); 5069 rctl |= E1000_RCTL_SZ_2048; 5070 rctl &= ~(E1000_RCTL_BSEX | E1000_RCTL_LPE); 5071 E1000_WRITE_REG(hw, RCTL, rctl); 5072 } 5073 5074 /** 5075 * e1000_configure_rx - Configure 8254x Receive Unit after Reset 5076 * @adapter: board private structure 5077 * 5078 * Configure the Rx unit of the MAC after a reset. 5079 **/ 5080 static void 5081 e1000_configure_rx(struct e1000_hw *hw) 5082 { 5083 unsigned long rctl, ctrl_ext; 5084 rx_tail = 0; 5085 5086 /* make sure receives are disabled while setting up the descriptors */ 5087 rctl = E1000_READ_REG(hw, RCTL); 5088 E1000_WRITE_REG(hw, RCTL, rctl & ~E1000_RCTL_EN); 5089 if (hw->mac_type >= e1000_82540) { 5090 /* Set the interrupt throttling rate. Value is calculated 5091 * as DEFAULT_ITR = 1/(MAX_INTS_PER_SEC * 256ns) */ 5092 #define MAX_INTS_PER_SEC 8000 5093 #define DEFAULT_ITR 1000000000/(MAX_INTS_PER_SEC * 256) 5094 E1000_WRITE_REG(hw, ITR, DEFAULT_ITR); 5095 } 5096 5097 if (hw->mac_type >= e1000_82571) { 5098 ctrl_ext = E1000_READ_REG(hw, CTRL_EXT); 5099 /* Reset delay timers after every interrupt */ 5100 ctrl_ext |= E1000_CTRL_EXT_INT_TIMER_CLR; 5101 E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext); 5102 E1000_WRITE_FLUSH(hw); 5103 } 5104 /* Setup the Base and Length of the Rx Descriptor Ring */ 5105 E1000_WRITE_REG(hw, RDBAL, lower_32_bits((unsigned long)rx_base)); 5106 E1000_WRITE_REG(hw, RDBAH, upper_32_bits((unsigned long)rx_base)); 5107 5108 E1000_WRITE_REG(hw, RDLEN, 128); 5109 5110 /* Setup the HW Rx Head and Tail Descriptor Pointers */ 5111 E1000_WRITE_REG(hw, RDH, 0); 5112 E1000_WRITE_REG(hw, RDT, 0); 5113 /* Enable Receives */ 5114 5115 if (hw->mac_type == e1000_igb) { 5116 5117 uint32_t reg_rxdctl = E1000_READ_REG(hw, RXDCTL); 5118 reg_rxdctl |= 1 << 25; 5119 E1000_WRITE_REG(hw, RXDCTL, reg_rxdctl); 5120 mdelay(20); 5121 } 5122 5123 E1000_WRITE_REG(hw, RCTL, rctl); 5124 5125 fill_rx(hw); 5126 } 5127 5128 /************************************************************************** 5129 POLL - Wait for a frame 5130 ***************************************************************************/ 5131 static int 5132 _e1000_poll(struct e1000_hw *hw) 5133 { 5134 struct e1000_rx_desc *rd; 5135 unsigned long inval_start, inval_end; 5136 uint32_t len; 5137 5138 /* return true if there's an ethernet packet ready to read */ 5139 rd = rx_base + rx_last; 5140 5141 /* Re-load the descriptor from RAM. */ 5142 inval_start = ((unsigned long)rd) & ~(ARCH_DMA_MINALIGN - 1); 5143 inval_end = inval_start + roundup(sizeof(*rd), ARCH_DMA_MINALIGN); 5144 invalidate_dcache_range(inval_start, inval_end); 5145 5146 if (!(rd->status & E1000_RXD_STAT_DD)) 5147 return 0; 5148 /* DEBUGOUT("recv: packet len=%d\n", rd->length); */ 5149 /* Packet received, make sure the data are re-loaded from RAM. */ 5150 len = le16_to_cpu(rd->length); 5151 invalidate_dcache_range((unsigned long)packet, 5152 (unsigned long)packet + 5153 roundup(len, ARCH_DMA_MINALIGN)); 5154 return len; 5155 } 5156 5157 static int _e1000_transmit(struct e1000_hw *hw, void *txpacket, int length) 5158 { 5159 void *nv_packet = (void *)txpacket; 5160 struct e1000_tx_desc *txp; 5161 int i = 0; 5162 unsigned long flush_start, flush_end; 5163 5164 txp = tx_base + tx_tail; 5165 tx_tail = (tx_tail + 1) % 8; 5166 5167 txp->buffer_addr = cpu_to_le64(virt_to_bus(hw->pdev, nv_packet)); 5168 txp->lower.data = cpu_to_le32(hw->txd_cmd | length); 5169 txp->upper.data = 0; 5170 5171 /* Dump the packet into RAM so e1000 can pick them. */ 5172 flush_dcache_range((unsigned long)nv_packet, 5173 (unsigned long)nv_packet + 5174 roundup(length, ARCH_DMA_MINALIGN)); 5175 /* Dump the descriptor into RAM as well. */ 5176 flush_start = ((unsigned long)txp) & ~(ARCH_DMA_MINALIGN - 1); 5177 flush_end = flush_start + roundup(sizeof(*txp), ARCH_DMA_MINALIGN); 5178 flush_dcache_range(flush_start, flush_end); 5179 5180 E1000_WRITE_REG(hw, TDT, tx_tail); 5181 5182 E1000_WRITE_FLUSH(hw); 5183 while (1) { 5184 invalidate_dcache_range(flush_start, flush_end); 5185 if (le32_to_cpu(txp->upper.data) & E1000_TXD_STAT_DD) 5186 break; 5187 if (i++ > TOUT_LOOP) { 5188 DEBUGOUT("e1000: tx timeout\n"); 5189 return 0; 5190 } 5191 udelay(10); /* give the nic a chance to write to the register */ 5192 } 5193 return 1; 5194 } 5195 5196 static void 5197 _e1000_disable(struct e1000_hw *hw) 5198 { 5199 /* Turn off the ethernet interface */ 5200 E1000_WRITE_REG(hw, RCTL, 0); 5201 E1000_WRITE_REG(hw, TCTL, 0); 5202 5203 /* Clear the transmit ring */ 5204 E1000_WRITE_REG(hw, TDH, 0); 5205 E1000_WRITE_REG(hw, TDT, 0); 5206 5207 /* Clear the receive ring */ 5208 E1000_WRITE_REG(hw, RDH, 0); 5209 E1000_WRITE_REG(hw, RDT, 0); 5210 5211 mdelay(10); 5212 } 5213 5214 /*reset function*/ 5215 static inline int 5216 e1000_reset(struct e1000_hw *hw, unsigned char enetaddr[6]) 5217 { 5218 e1000_reset_hw(hw); 5219 if (hw->mac_type >= e1000_82544) 5220 E1000_WRITE_REG(hw, WUC, 0); 5221 5222 return e1000_init_hw(hw, enetaddr); 5223 } 5224 5225 static int 5226 _e1000_init(struct e1000_hw *hw, unsigned char enetaddr[6]) 5227 { 5228 int ret_val = 0; 5229 5230 ret_val = e1000_reset(hw, enetaddr); 5231 if (ret_val < 0) { 5232 if ((ret_val == -E1000_ERR_NOLINK) || 5233 (ret_val == -E1000_ERR_TIMEOUT)) { 5234 E1000_ERR(hw, "Valid Link not detected: %d\n", ret_val); 5235 } else { 5236 E1000_ERR(hw, "Hardware Initialization Failed\n"); 5237 } 5238 return ret_val; 5239 } 5240 e1000_configure_tx(hw); 5241 e1000_setup_rctl(hw); 5242 e1000_configure_rx(hw); 5243 return 0; 5244 } 5245 5246 /****************************************************************************** 5247 * Gets the current PCI bus type of hardware 5248 * 5249 * hw - Struct containing variables accessed by shared code 5250 *****************************************************************************/ 5251 void e1000_get_bus_type(struct e1000_hw *hw) 5252 { 5253 uint32_t status; 5254 5255 switch (hw->mac_type) { 5256 case e1000_82542_rev2_0: 5257 case e1000_82542_rev2_1: 5258 hw->bus_type = e1000_bus_type_pci; 5259 break; 5260 case e1000_82571: 5261 case e1000_82572: 5262 case e1000_82573: 5263 case e1000_82574: 5264 case e1000_80003es2lan: 5265 case e1000_ich8lan: 5266 case e1000_igb: 5267 hw->bus_type = e1000_bus_type_pci_express; 5268 break; 5269 default: 5270 status = E1000_READ_REG(hw, STATUS); 5271 hw->bus_type = (status & E1000_STATUS_PCIX_MODE) ? 5272 e1000_bus_type_pcix : e1000_bus_type_pci; 5273 break; 5274 } 5275 } 5276 5277 #ifndef CONFIG_DM_ETH 5278 /* A list of all registered e1000 devices */ 5279 static LIST_HEAD(e1000_hw_list); 5280 #endif 5281 5282 #ifdef CONFIG_DM_ETH 5283 static int e1000_init_one(struct e1000_hw *hw, int cardnum, 5284 struct udevice *devno, unsigned char enetaddr[6]) 5285 #else 5286 static int e1000_init_one(struct e1000_hw *hw, int cardnum, pci_dev_t devno, 5287 unsigned char enetaddr[6]) 5288 #endif 5289 { 5290 u32 val; 5291 5292 /* Assign the passed-in values */ 5293 #ifdef CONFIG_DM_ETH 5294 hw->pdev = devno; 5295 #else 5296 hw->pdev = devno; 5297 #endif 5298 hw->cardnum = cardnum; 5299 5300 /* Print a debug message with the IO base address */ 5301 #ifdef CONFIG_DM_ETH 5302 dm_pci_read_config32(devno, PCI_BASE_ADDRESS_0, &val); 5303 #else 5304 pci_read_config_dword(devno, PCI_BASE_ADDRESS_0, &val); 5305 #endif 5306 E1000_DBG(hw, "iobase 0x%08x\n", val & 0xfffffff0); 5307 5308 /* Try to enable I/O accesses and bus-mastering */ 5309 val = PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER; 5310 #ifdef CONFIG_DM_ETH 5311 dm_pci_write_config32(devno, PCI_COMMAND, val); 5312 #else 5313 pci_write_config_dword(devno, PCI_COMMAND, val); 5314 #endif 5315 5316 /* Make sure it worked */ 5317 #ifdef CONFIG_DM_ETH 5318 dm_pci_read_config32(devno, PCI_COMMAND, &val); 5319 #else 5320 pci_read_config_dword(devno, PCI_COMMAND, &val); 5321 #endif 5322 if (!(val & PCI_COMMAND_MEMORY)) { 5323 E1000_ERR(hw, "Can't enable I/O memory\n"); 5324 return -ENOSPC; 5325 } 5326 if (!(val & PCI_COMMAND_MASTER)) { 5327 E1000_ERR(hw, "Can't enable bus-mastering\n"); 5328 return -EPERM; 5329 } 5330 5331 /* Are these variables needed? */ 5332 hw->fc = e1000_fc_default; 5333 hw->original_fc = e1000_fc_default; 5334 hw->autoneg_failed = 0; 5335 hw->autoneg = 1; 5336 hw->get_link_status = true; 5337 #ifndef CONFIG_E1000_NO_NVM 5338 hw->eeprom_semaphore_present = true; 5339 #endif 5340 #ifdef CONFIG_DM_ETH 5341 hw->hw_addr = dm_pci_map_bar(devno, PCI_BASE_ADDRESS_0, 5342 PCI_REGION_MEM); 5343 #else 5344 hw->hw_addr = pci_map_bar(devno, PCI_BASE_ADDRESS_0, 5345 PCI_REGION_MEM); 5346 #endif 5347 hw->mac_type = e1000_undefined; 5348 5349 /* MAC and Phy settings */ 5350 if (e1000_sw_init(hw) < 0) { 5351 E1000_ERR(hw, "Software init failed\n"); 5352 return -EIO; 5353 } 5354 if (e1000_check_phy_reset_block(hw)) 5355 E1000_ERR(hw, "PHY Reset is blocked!\n"); 5356 5357 /* Basic init was OK, reset the hardware and allow SPI access */ 5358 e1000_reset_hw(hw); 5359 5360 #ifndef CONFIG_E1000_NO_NVM 5361 /* Validate the EEPROM and get chipset information */ 5362 if (e1000_init_eeprom_params(hw)) { 5363 E1000_ERR(hw, "EEPROM is invalid!\n"); 5364 return -EINVAL; 5365 } 5366 if ((E1000_READ_REG(hw, I210_EECD) & E1000_EECD_FLUPD) && 5367 e1000_validate_eeprom_checksum(hw)) 5368 return -ENXIO; 5369 e1000_read_mac_addr(hw, enetaddr); 5370 #endif 5371 e1000_get_bus_type(hw); 5372 5373 #ifndef CONFIG_E1000_NO_NVM 5374 printf("e1000: %02x:%02x:%02x:%02x:%02x:%02x\n ", 5375 enetaddr[0], enetaddr[1], enetaddr[2], 5376 enetaddr[3], enetaddr[4], enetaddr[5]); 5377 #else 5378 memset(enetaddr, 0, 6); 5379 printf("e1000: no NVM\n"); 5380 #endif 5381 5382 return 0; 5383 } 5384 5385 /* Put the name of a device in a string */ 5386 static void e1000_name(char *str, int cardnum) 5387 { 5388 sprintf(str, "e1000#%u", cardnum); 5389 } 5390 5391 #ifndef CONFIG_DM_ETH 5392 /************************************************************************** 5393 TRANSMIT - Transmit a frame 5394 ***************************************************************************/ 5395 static int e1000_transmit(struct eth_device *nic, void *txpacket, int length) 5396 { 5397 struct e1000_hw *hw = nic->priv; 5398 5399 return _e1000_transmit(hw, txpacket, length); 5400 } 5401 5402 /************************************************************************** 5403 DISABLE - Turn off ethernet interface 5404 ***************************************************************************/ 5405 static void 5406 e1000_disable(struct eth_device *nic) 5407 { 5408 struct e1000_hw *hw = nic->priv; 5409 5410 _e1000_disable(hw); 5411 } 5412 5413 /************************************************************************** 5414 INIT - set up ethernet interface(s) 5415 ***************************************************************************/ 5416 static int 5417 e1000_init(struct eth_device *nic, bd_t *bis) 5418 { 5419 struct e1000_hw *hw = nic->priv; 5420 5421 return _e1000_init(hw, nic->enetaddr); 5422 } 5423 5424 static int 5425 e1000_poll(struct eth_device *nic) 5426 { 5427 struct e1000_hw *hw = nic->priv; 5428 int len; 5429 5430 len = _e1000_poll(hw); 5431 if (len) { 5432 net_process_received_packet((uchar *)packet, len); 5433 fill_rx(hw); 5434 } 5435 5436 return len ? 1 : 0; 5437 } 5438 5439 /************************************************************************** 5440 PROBE - Look for an adapter, this routine's visible to the outside 5441 You should omit the last argument struct pci_device * for a non-PCI NIC 5442 ***************************************************************************/ 5443 int 5444 e1000_initialize(bd_t * bis) 5445 { 5446 unsigned int i; 5447 pci_dev_t devno; 5448 int ret; 5449 5450 DEBUGFUNC(); 5451 5452 /* Find and probe all the matching PCI devices */ 5453 for (i = 0; (devno = pci_find_devices(e1000_supported, i)) >= 0; i++) { 5454 /* 5455 * These will never get freed due to errors, this allows us to 5456 * perform SPI EEPROM programming from U-Boot, for example. 5457 */ 5458 struct eth_device *nic = malloc(sizeof(*nic)); 5459 struct e1000_hw *hw = malloc(sizeof(*hw)); 5460 if (!nic || !hw) { 5461 printf("e1000#%u: Out of Memory!\n", i); 5462 free(nic); 5463 free(hw); 5464 continue; 5465 } 5466 5467 /* Make sure all of the fields are initially zeroed */ 5468 memset(nic, 0, sizeof(*nic)); 5469 memset(hw, 0, sizeof(*hw)); 5470 nic->priv = hw; 5471 5472 /* Generate a card name */ 5473 e1000_name(nic->name, i); 5474 hw->name = nic->name; 5475 5476 ret = e1000_init_one(hw, i, devno, nic->enetaddr); 5477 if (ret) 5478 continue; 5479 list_add_tail(&hw->list_node, &e1000_hw_list); 5480 5481 hw->nic = nic; 5482 5483 /* Set up the function pointers and register the device */ 5484 nic->init = e1000_init; 5485 nic->recv = e1000_poll; 5486 nic->send = e1000_transmit; 5487 nic->halt = e1000_disable; 5488 eth_register(nic); 5489 } 5490 5491 return i; 5492 } 5493 5494 struct e1000_hw *e1000_find_card(unsigned int cardnum) 5495 { 5496 struct e1000_hw *hw; 5497 5498 list_for_each_entry(hw, &e1000_hw_list, list_node) 5499 if (hw->cardnum == cardnum) 5500 return hw; 5501 5502 return NULL; 5503 } 5504 #endif /* !CONFIG_DM_ETH */ 5505 5506 #ifdef CONFIG_CMD_E1000 5507 static int do_e1000(cmd_tbl_t *cmdtp, int flag, 5508 int argc, char * const argv[]) 5509 { 5510 unsigned char *mac = NULL; 5511 #ifdef CONFIG_DM_ETH 5512 struct eth_pdata *plat; 5513 struct udevice *dev; 5514 char name[30]; 5515 int ret; 5516 #endif 5517 #if !defined(CONFIG_DM_ETH) || defined(CONFIG_E1000_SPI) 5518 struct e1000_hw *hw; 5519 #endif 5520 int cardnum; 5521 5522 if (argc < 3) { 5523 cmd_usage(cmdtp); 5524 return 1; 5525 } 5526 5527 /* Make sure we can find the requested e1000 card */ 5528 cardnum = simple_strtoul(argv[1], NULL, 10); 5529 #ifdef CONFIG_DM_ETH 5530 e1000_name(name, cardnum); 5531 ret = uclass_get_device_by_name(UCLASS_ETH, name, &dev); 5532 if (!ret) { 5533 plat = dev_get_platdata(dev); 5534 mac = plat->enetaddr; 5535 } 5536 #else 5537 hw = e1000_find_card(cardnum); 5538 if (hw) 5539 mac = hw->nic->enetaddr; 5540 #endif 5541 if (!mac) { 5542 printf("e1000: ERROR: No such device: e1000#%s\n", argv[1]); 5543 return 1; 5544 } 5545 5546 if (!strcmp(argv[2], "print-mac-address")) { 5547 printf("%02x:%02x:%02x:%02x:%02x:%02x\n", 5548 mac[0], mac[1], mac[2], mac[3], mac[4], mac[5]); 5549 return 0; 5550 } 5551 5552 #ifdef CONFIG_E1000_SPI 5553 #ifdef CONFIG_DM_ETH 5554 hw = dev_get_priv(dev); 5555 #endif 5556 /* Handle the "SPI" subcommand */ 5557 if (!strcmp(argv[2], "spi")) 5558 return do_e1000_spi(cmdtp, hw, argc - 3, argv + 3); 5559 #endif 5560 5561 cmd_usage(cmdtp); 5562 return 1; 5563 } 5564 5565 U_BOOT_CMD( 5566 e1000, 7, 0, do_e1000, 5567 "Intel e1000 controller management", 5568 /* */"<card#> print-mac-address\n" 5569 #ifdef CONFIG_E1000_SPI 5570 "e1000 <card#> spi show [<offset> [<length>]]\n" 5571 "e1000 <card#> spi dump <addr> <offset> <length>\n" 5572 "e1000 <card#> spi program <addr> <offset> <length>\n" 5573 "e1000 <card#> spi checksum [update]\n" 5574 #endif 5575 " - Manage the Intel E1000 PCI device" 5576 ); 5577 #endif /* not CONFIG_CMD_E1000 */ 5578 5579 #ifdef CONFIG_DM_ETH 5580 static int e1000_eth_start(struct udevice *dev) 5581 { 5582 struct eth_pdata *plat = dev_get_platdata(dev); 5583 struct e1000_hw *hw = dev_get_priv(dev); 5584 5585 return _e1000_init(hw, plat->enetaddr); 5586 } 5587 5588 static void e1000_eth_stop(struct udevice *dev) 5589 { 5590 struct e1000_hw *hw = dev_get_priv(dev); 5591 5592 _e1000_disable(hw); 5593 } 5594 5595 static int e1000_eth_send(struct udevice *dev, void *packet, int length) 5596 { 5597 struct e1000_hw *hw = dev_get_priv(dev); 5598 int ret; 5599 5600 ret = _e1000_transmit(hw, packet, length); 5601 5602 return ret ? 0 : -ETIMEDOUT; 5603 } 5604 5605 static int e1000_eth_recv(struct udevice *dev, int flags, uchar **packetp) 5606 { 5607 struct e1000_hw *hw = dev_get_priv(dev); 5608 int len; 5609 5610 len = _e1000_poll(hw); 5611 if (len) 5612 *packetp = packet; 5613 5614 return len ? len : -EAGAIN; 5615 } 5616 5617 static int e1000_free_pkt(struct udevice *dev, uchar *packet, int length) 5618 { 5619 struct e1000_hw *hw = dev_get_priv(dev); 5620 5621 fill_rx(hw); 5622 5623 return 0; 5624 } 5625 5626 static int e1000_eth_probe(struct udevice *dev) 5627 { 5628 struct eth_pdata *plat = dev_get_platdata(dev); 5629 struct e1000_hw *hw = dev_get_priv(dev); 5630 int ret; 5631 5632 hw->name = dev->name; 5633 ret = e1000_init_one(hw, trailing_strtol(dev->name), 5634 dev, plat->enetaddr); 5635 if (ret < 0) { 5636 printf(pr_fmt("failed to initialize card: %d\n"), ret); 5637 return ret; 5638 } 5639 5640 return 0; 5641 } 5642 5643 static int e1000_eth_bind(struct udevice *dev) 5644 { 5645 char name[20]; 5646 5647 /* 5648 * A simple way to number the devices. When device tree is used this 5649 * is unnecessary, but when the device is just discovered on the PCI 5650 * bus we need a name. We could instead have the uclass figure out 5651 * which devices are different and number them. 5652 */ 5653 e1000_name(name, num_cards++); 5654 5655 return device_set_name(dev, name); 5656 } 5657 5658 static const struct eth_ops e1000_eth_ops = { 5659 .start = e1000_eth_start, 5660 .send = e1000_eth_send, 5661 .recv = e1000_eth_recv, 5662 .stop = e1000_eth_stop, 5663 .free_pkt = e1000_free_pkt, 5664 }; 5665 5666 static const struct udevice_id e1000_eth_ids[] = { 5667 { .compatible = "intel,e1000" }, 5668 { } 5669 }; 5670 5671 U_BOOT_DRIVER(eth_e1000) = { 5672 .name = "eth_e1000", 5673 .id = UCLASS_ETH, 5674 .of_match = e1000_eth_ids, 5675 .bind = e1000_eth_bind, 5676 .probe = e1000_eth_probe, 5677 .ops = &e1000_eth_ops, 5678 .priv_auto_alloc_size = sizeof(struct e1000_hw), 5679 .platdata_auto_alloc_size = sizeof(struct eth_pdata), 5680 }; 5681 5682 U_BOOT_PCI_DEVICE(eth_e1000, e1000_supported); 5683 #endif 5684