1 /************************************************************************** 2 Intel Pro 1000 for ppcboot/das-u-boot 3 Drivers are port from Intel's Linux driver e1000-4.3.15 4 and from Etherboot pro 1000 driver by mrakes at vivato dot net 5 tested on both gig copper and gig fiber boards 6 ***************************************************************************/ 7 /******************************************************************************* 8 9 10 Copyright(c) 1999 - 2002 Intel Corporation. All rights reserved. 11 12 This program is free software; you can redistribute it and/or modify it 13 under the terms of the GNU General Public License as published by the Free 14 Software Foundation; either version 2 of the License, or (at your option) 15 any later version. 16 17 This program is distributed in the hope that it will be useful, but WITHOUT 18 ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or 19 FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for 20 more details. 21 22 You should have received a copy of the GNU General Public License along with 23 this program; if not, write to the Free Software Foundation, Inc., 59 24 Temple Place - Suite 330, Boston, MA 02111-1307, USA. 25 26 The full GNU General Public License is included in this distribution in the 27 file called LICENSE. 28 29 Contact Information: 30 Linux NICS <linux.nics@intel.com> 31 Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 32 33 *******************************************************************************/ 34 /* 35 * Copyright (C) Archway Digital Solutions. 36 * 37 * written by Chrsitopher Li <cli at arcyway dot com> or <chrisl at gnuchina dot org> 38 * 2/9/2002 39 * 40 * Copyright (C) Linux Networx. 41 * Massive upgrade to work with the new intel gigabit NICs. 42 * <ebiederman at lnxi dot com> 43 * 44 * Copyright 2011 Freescale Semiconductor, Inc. 45 */ 46 47 #include "e1000.h" 48 49 #define TOUT_LOOP 100000 50 51 #define virt_to_bus(devno, v) pci_virt_to_mem(devno, (void *) (v)) 52 #define bus_to_phys(devno, a) pci_mem_to_phys(devno, a) 53 54 #define E1000_DEFAULT_PCI_PBA 0x00000030 55 #define E1000_DEFAULT_PCIE_PBA 0x000a0026 56 57 /* NIC specific static variables go here */ 58 59 static char tx_pool[128 + 16]; 60 static char rx_pool[128 + 16]; 61 static char packet[2096]; 62 63 static struct e1000_tx_desc *tx_base; 64 static struct e1000_rx_desc *rx_base; 65 66 static int tx_tail; 67 static int rx_tail, rx_last; 68 69 static struct pci_device_id e1000_supported[] = { 70 {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82542}, 71 {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82543GC_FIBER}, 72 {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82543GC_COPPER}, 73 {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82544EI_COPPER}, 74 {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82544EI_FIBER}, 75 {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82544GC_COPPER}, 76 {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82544GC_LOM}, 77 {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82540EM}, 78 {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82545EM_COPPER}, 79 {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82545GM_COPPER}, 80 {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82546EB_COPPER}, 81 {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82545EM_FIBER}, 82 {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82546EB_FIBER}, 83 {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82546GB_COPPER}, 84 {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82540EM_LOM}, 85 {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82541ER}, 86 {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82541GI_LF}, 87 /* E1000 PCIe card */ 88 {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_COPPER}, 89 {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_FIBER }, 90 {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_SERDES }, 91 {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_QUAD_COPPER}, 92 {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571PT_QUAD_COPPER}, 93 {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_QUAD_FIBER}, 94 {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_QUAD_COPPER_LOWPROFILE}, 95 {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_SERDES_DUAL}, 96 {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82571EB_SERDES_QUAD}, 97 {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82572EI_COPPER}, 98 {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82572EI_FIBER}, 99 {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82572EI_SERDES}, 100 {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82572EI}, 101 {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82573E}, 102 {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82573E_IAMT}, 103 {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82573L}, 104 {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82574L}, 105 {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82546GB_QUAD_COPPER_KSP3}, 106 {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80003ES2LAN_COPPER_DPT}, 107 {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80003ES2LAN_SERDES_DPT}, 108 {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80003ES2LAN_COPPER_SPT}, 109 {PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_80003ES2LAN_SERDES_SPT}, 110 {} 111 }; 112 113 /* Function forward declarations */ 114 static int e1000_setup_link(struct eth_device *nic); 115 static int e1000_setup_fiber_link(struct eth_device *nic); 116 static int e1000_setup_copper_link(struct eth_device *nic); 117 static int e1000_phy_setup_autoneg(struct e1000_hw *hw); 118 static void e1000_config_collision_dist(struct e1000_hw *hw); 119 static int e1000_config_mac_to_phy(struct e1000_hw *hw); 120 static int e1000_config_fc_after_link_up(struct e1000_hw *hw); 121 static int e1000_check_for_link(struct eth_device *nic); 122 static int e1000_wait_autoneg(struct e1000_hw *hw); 123 static int e1000_get_speed_and_duplex(struct e1000_hw *hw, uint16_t * speed, 124 uint16_t * duplex); 125 static int e1000_read_phy_reg(struct e1000_hw *hw, uint32_t reg_addr, 126 uint16_t * phy_data); 127 static int e1000_write_phy_reg(struct e1000_hw *hw, uint32_t reg_addr, 128 uint16_t phy_data); 129 static int32_t e1000_phy_hw_reset(struct e1000_hw *hw); 130 static int e1000_phy_reset(struct e1000_hw *hw); 131 static int e1000_detect_gig_phy(struct e1000_hw *hw); 132 static void e1000_put_hw_eeprom_semaphore(struct e1000_hw *hw); 133 static void e1000_set_media_type(struct e1000_hw *hw); 134 135 static int32_t e1000_swfw_sync_acquire(struct e1000_hw *hw, uint16_t mask); 136 static int32_t e1000_check_phy_reset_block(struct e1000_hw *hw); 137 138 #ifndef CONFIG_AP1000 /* remove for warnings */ 139 static int32_t e1000_read_eeprom(struct e1000_hw *hw, uint16_t offset, 140 uint16_t words, 141 uint16_t *data); 142 /****************************************************************************** 143 * Raises the EEPROM's clock input. 144 * 145 * hw - Struct containing variables accessed by shared code 146 * eecd - EECD's current value 147 *****************************************************************************/ 148 void e1000_raise_ee_clk(struct e1000_hw *hw, uint32_t * eecd) 149 { 150 /* Raise the clock input to the EEPROM (by setting the SK bit), and then 151 * wait 50 microseconds. 152 */ 153 *eecd = *eecd | E1000_EECD_SK; 154 E1000_WRITE_REG(hw, EECD, *eecd); 155 E1000_WRITE_FLUSH(hw); 156 udelay(50); 157 } 158 159 /****************************************************************************** 160 * Lowers the EEPROM's clock input. 161 * 162 * hw - Struct containing variables accessed by shared code 163 * eecd - EECD's current value 164 *****************************************************************************/ 165 void e1000_lower_ee_clk(struct e1000_hw *hw, uint32_t * eecd) 166 { 167 /* Lower the clock input to the EEPROM (by clearing the SK bit), and then 168 * wait 50 microseconds. 169 */ 170 *eecd = *eecd & ~E1000_EECD_SK; 171 E1000_WRITE_REG(hw, EECD, *eecd); 172 E1000_WRITE_FLUSH(hw); 173 udelay(50); 174 } 175 176 /****************************************************************************** 177 * Shift data bits out to the EEPROM. 178 * 179 * hw - Struct containing variables accessed by shared code 180 * data - data to send to the EEPROM 181 * count - number of bits to shift out 182 *****************************************************************************/ 183 static void 184 e1000_shift_out_ee_bits(struct e1000_hw *hw, uint16_t data, uint16_t count) 185 { 186 uint32_t eecd; 187 uint32_t mask; 188 189 /* We need to shift "count" bits out to the EEPROM. So, value in the 190 * "data" parameter will be shifted out to the EEPROM one bit at a time. 191 * In order to do this, "data" must be broken down into bits. 192 */ 193 mask = 0x01 << (count - 1); 194 eecd = E1000_READ_REG(hw, EECD); 195 eecd &= ~(E1000_EECD_DO | E1000_EECD_DI); 196 do { 197 /* A "1" is shifted out to the EEPROM by setting bit "DI" to a "1", 198 * and then raising and then lowering the clock (the SK bit controls 199 * the clock input to the EEPROM). A "0" is shifted out to the EEPROM 200 * by setting "DI" to "0" and then raising and then lowering the clock. 201 */ 202 eecd &= ~E1000_EECD_DI; 203 204 if (data & mask) 205 eecd |= E1000_EECD_DI; 206 207 E1000_WRITE_REG(hw, EECD, eecd); 208 E1000_WRITE_FLUSH(hw); 209 210 udelay(50); 211 212 e1000_raise_ee_clk(hw, &eecd); 213 e1000_lower_ee_clk(hw, &eecd); 214 215 mask = mask >> 1; 216 217 } while (mask); 218 219 /* We leave the "DI" bit set to "0" when we leave this routine. */ 220 eecd &= ~E1000_EECD_DI; 221 E1000_WRITE_REG(hw, EECD, eecd); 222 } 223 224 /****************************************************************************** 225 * Shift data bits in from the EEPROM 226 * 227 * hw - Struct containing variables accessed by shared code 228 *****************************************************************************/ 229 static uint16_t 230 e1000_shift_in_ee_bits(struct e1000_hw *hw, uint16_t count) 231 { 232 uint32_t eecd; 233 uint32_t i; 234 uint16_t data; 235 236 /* In order to read a register from the EEPROM, we need to shift 'count' 237 * bits in from the EEPROM. Bits are "shifted in" by raising the clock 238 * input to the EEPROM (setting the SK bit), and then reading the 239 * value of the "DO" bit. During this "shifting in" process the 240 * "DI" bit should always be clear. 241 */ 242 243 eecd = E1000_READ_REG(hw, EECD); 244 245 eecd &= ~(E1000_EECD_DO | E1000_EECD_DI); 246 data = 0; 247 248 for (i = 0; i < count; i++) { 249 data = data << 1; 250 e1000_raise_ee_clk(hw, &eecd); 251 252 eecd = E1000_READ_REG(hw, EECD); 253 254 eecd &= ~(E1000_EECD_DI); 255 if (eecd & E1000_EECD_DO) 256 data |= 1; 257 258 e1000_lower_ee_clk(hw, &eecd); 259 } 260 261 return data; 262 } 263 264 /****************************************************************************** 265 * Returns EEPROM to a "standby" state 266 * 267 * hw - Struct containing variables accessed by shared code 268 *****************************************************************************/ 269 void e1000_standby_eeprom(struct e1000_hw *hw) 270 { 271 struct e1000_eeprom_info *eeprom = &hw->eeprom; 272 uint32_t eecd; 273 274 eecd = E1000_READ_REG(hw, EECD); 275 276 if (eeprom->type == e1000_eeprom_microwire) { 277 eecd &= ~(E1000_EECD_CS | E1000_EECD_SK); 278 E1000_WRITE_REG(hw, EECD, eecd); 279 E1000_WRITE_FLUSH(hw); 280 udelay(eeprom->delay_usec); 281 282 /* Clock high */ 283 eecd |= E1000_EECD_SK; 284 E1000_WRITE_REG(hw, EECD, eecd); 285 E1000_WRITE_FLUSH(hw); 286 udelay(eeprom->delay_usec); 287 288 /* Select EEPROM */ 289 eecd |= E1000_EECD_CS; 290 E1000_WRITE_REG(hw, EECD, eecd); 291 E1000_WRITE_FLUSH(hw); 292 udelay(eeprom->delay_usec); 293 294 /* Clock low */ 295 eecd &= ~E1000_EECD_SK; 296 E1000_WRITE_REG(hw, EECD, eecd); 297 E1000_WRITE_FLUSH(hw); 298 udelay(eeprom->delay_usec); 299 } else if (eeprom->type == e1000_eeprom_spi) { 300 /* Toggle CS to flush commands */ 301 eecd |= E1000_EECD_CS; 302 E1000_WRITE_REG(hw, EECD, eecd); 303 E1000_WRITE_FLUSH(hw); 304 udelay(eeprom->delay_usec); 305 eecd &= ~E1000_EECD_CS; 306 E1000_WRITE_REG(hw, EECD, eecd); 307 E1000_WRITE_FLUSH(hw); 308 udelay(eeprom->delay_usec); 309 } 310 } 311 312 /*************************************************************************** 313 * Description: Determines if the onboard NVM is FLASH or EEPROM. 314 * 315 * hw - Struct containing variables accessed by shared code 316 ****************************************************************************/ 317 static boolean_t e1000_is_onboard_nvm_eeprom(struct e1000_hw *hw) 318 { 319 uint32_t eecd = 0; 320 321 DEBUGFUNC(); 322 323 if (hw->mac_type == e1000_ich8lan) 324 return FALSE; 325 326 if (hw->mac_type == e1000_82573 || hw->mac_type == e1000_82574) { 327 eecd = E1000_READ_REG(hw, EECD); 328 329 /* Isolate bits 15 & 16 */ 330 eecd = ((eecd >> 15) & 0x03); 331 332 /* If both bits are set, device is Flash type */ 333 if (eecd == 0x03) 334 return FALSE; 335 } 336 return TRUE; 337 } 338 339 /****************************************************************************** 340 * Prepares EEPROM for access 341 * 342 * hw - Struct containing variables accessed by shared code 343 * 344 * Lowers EEPROM clock. Clears input pin. Sets the chip select pin. This 345 * function should be called before issuing a command to the EEPROM. 346 *****************************************************************************/ 347 int32_t e1000_acquire_eeprom(struct e1000_hw *hw) 348 { 349 struct e1000_eeprom_info *eeprom = &hw->eeprom; 350 uint32_t eecd, i = 0; 351 352 DEBUGFUNC(); 353 354 if (e1000_swfw_sync_acquire(hw, E1000_SWFW_EEP_SM)) 355 return -E1000_ERR_SWFW_SYNC; 356 eecd = E1000_READ_REG(hw, EECD); 357 358 if (hw->mac_type != e1000_82573 || hw->mac_type != e1000_82574) { 359 /* Request EEPROM Access */ 360 if (hw->mac_type > e1000_82544) { 361 eecd |= E1000_EECD_REQ; 362 E1000_WRITE_REG(hw, EECD, eecd); 363 eecd = E1000_READ_REG(hw, EECD); 364 while ((!(eecd & E1000_EECD_GNT)) && 365 (i < E1000_EEPROM_GRANT_ATTEMPTS)) { 366 i++; 367 udelay(5); 368 eecd = E1000_READ_REG(hw, EECD); 369 } 370 if (!(eecd & E1000_EECD_GNT)) { 371 eecd &= ~E1000_EECD_REQ; 372 E1000_WRITE_REG(hw, EECD, eecd); 373 DEBUGOUT("Could not acquire EEPROM grant\n"); 374 return -E1000_ERR_EEPROM; 375 } 376 } 377 } 378 379 /* Setup EEPROM for Read/Write */ 380 381 if (eeprom->type == e1000_eeprom_microwire) { 382 /* Clear SK and DI */ 383 eecd &= ~(E1000_EECD_DI | E1000_EECD_SK); 384 E1000_WRITE_REG(hw, EECD, eecd); 385 386 /* Set CS */ 387 eecd |= E1000_EECD_CS; 388 E1000_WRITE_REG(hw, EECD, eecd); 389 } else if (eeprom->type == e1000_eeprom_spi) { 390 /* Clear SK and CS */ 391 eecd &= ~(E1000_EECD_CS | E1000_EECD_SK); 392 E1000_WRITE_REG(hw, EECD, eecd); 393 udelay(1); 394 } 395 396 return E1000_SUCCESS; 397 } 398 399 /****************************************************************************** 400 * Sets up eeprom variables in the hw struct. Must be called after mac_type 401 * is configured. Additionally, if this is ICH8, the flash controller GbE 402 * registers must be mapped, or this will crash. 403 * 404 * hw - Struct containing variables accessed by shared code 405 *****************************************************************************/ 406 static int32_t e1000_init_eeprom_params(struct e1000_hw *hw) 407 { 408 struct e1000_eeprom_info *eeprom = &hw->eeprom; 409 uint32_t eecd = E1000_READ_REG(hw, EECD); 410 int32_t ret_val = E1000_SUCCESS; 411 uint16_t eeprom_size; 412 413 DEBUGFUNC(); 414 415 switch (hw->mac_type) { 416 case e1000_82542_rev2_0: 417 case e1000_82542_rev2_1: 418 case e1000_82543: 419 case e1000_82544: 420 eeprom->type = e1000_eeprom_microwire; 421 eeprom->word_size = 64; 422 eeprom->opcode_bits = 3; 423 eeprom->address_bits = 6; 424 eeprom->delay_usec = 50; 425 eeprom->use_eerd = FALSE; 426 eeprom->use_eewr = FALSE; 427 break; 428 case e1000_82540: 429 case e1000_82545: 430 case e1000_82545_rev_3: 431 case e1000_82546: 432 case e1000_82546_rev_3: 433 eeprom->type = e1000_eeprom_microwire; 434 eeprom->opcode_bits = 3; 435 eeprom->delay_usec = 50; 436 if (eecd & E1000_EECD_SIZE) { 437 eeprom->word_size = 256; 438 eeprom->address_bits = 8; 439 } else { 440 eeprom->word_size = 64; 441 eeprom->address_bits = 6; 442 } 443 eeprom->use_eerd = FALSE; 444 eeprom->use_eewr = FALSE; 445 break; 446 case e1000_82541: 447 case e1000_82541_rev_2: 448 case e1000_82547: 449 case e1000_82547_rev_2: 450 if (eecd & E1000_EECD_TYPE) { 451 eeprom->type = e1000_eeprom_spi; 452 eeprom->opcode_bits = 8; 453 eeprom->delay_usec = 1; 454 if (eecd & E1000_EECD_ADDR_BITS) { 455 eeprom->page_size = 32; 456 eeprom->address_bits = 16; 457 } else { 458 eeprom->page_size = 8; 459 eeprom->address_bits = 8; 460 } 461 } else { 462 eeprom->type = e1000_eeprom_microwire; 463 eeprom->opcode_bits = 3; 464 eeprom->delay_usec = 50; 465 if (eecd & E1000_EECD_ADDR_BITS) { 466 eeprom->word_size = 256; 467 eeprom->address_bits = 8; 468 } else { 469 eeprom->word_size = 64; 470 eeprom->address_bits = 6; 471 } 472 } 473 eeprom->use_eerd = FALSE; 474 eeprom->use_eewr = FALSE; 475 break; 476 case e1000_82571: 477 case e1000_82572: 478 eeprom->type = e1000_eeprom_spi; 479 eeprom->opcode_bits = 8; 480 eeprom->delay_usec = 1; 481 if (eecd & E1000_EECD_ADDR_BITS) { 482 eeprom->page_size = 32; 483 eeprom->address_bits = 16; 484 } else { 485 eeprom->page_size = 8; 486 eeprom->address_bits = 8; 487 } 488 eeprom->use_eerd = FALSE; 489 eeprom->use_eewr = FALSE; 490 break; 491 case e1000_82573: 492 case e1000_82574: 493 eeprom->type = e1000_eeprom_spi; 494 eeprom->opcode_bits = 8; 495 eeprom->delay_usec = 1; 496 if (eecd & E1000_EECD_ADDR_BITS) { 497 eeprom->page_size = 32; 498 eeprom->address_bits = 16; 499 } else { 500 eeprom->page_size = 8; 501 eeprom->address_bits = 8; 502 } 503 eeprom->use_eerd = TRUE; 504 eeprom->use_eewr = TRUE; 505 if (e1000_is_onboard_nvm_eeprom(hw) == FALSE) { 506 eeprom->type = e1000_eeprom_flash; 507 eeprom->word_size = 2048; 508 509 /* Ensure that the Autonomous FLASH update bit is cleared due to 510 * Flash update issue on parts which use a FLASH for NVM. */ 511 eecd &= ~E1000_EECD_AUPDEN; 512 E1000_WRITE_REG(hw, EECD, eecd); 513 } 514 break; 515 case e1000_80003es2lan: 516 eeprom->type = e1000_eeprom_spi; 517 eeprom->opcode_bits = 8; 518 eeprom->delay_usec = 1; 519 if (eecd & E1000_EECD_ADDR_BITS) { 520 eeprom->page_size = 32; 521 eeprom->address_bits = 16; 522 } else { 523 eeprom->page_size = 8; 524 eeprom->address_bits = 8; 525 } 526 eeprom->use_eerd = TRUE; 527 eeprom->use_eewr = FALSE; 528 break; 529 530 /* ich8lan does not support currently. if needed, please 531 * add corresponding code and functions. 532 */ 533 #if 0 534 case e1000_ich8lan: 535 { 536 int32_t i = 0; 537 538 eeprom->type = e1000_eeprom_ich8; 539 eeprom->use_eerd = FALSE; 540 eeprom->use_eewr = FALSE; 541 eeprom->word_size = E1000_SHADOW_RAM_WORDS; 542 uint32_t flash_size = E1000_READ_ICH_FLASH_REG(hw, 543 ICH_FLASH_GFPREG); 544 /* Zero the shadow RAM structure. But don't load it from NVM 545 * so as to save time for driver init */ 546 if (hw->eeprom_shadow_ram != NULL) { 547 for (i = 0; i < E1000_SHADOW_RAM_WORDS; i++) { 548 hw->eeprom_shadow_ram[i].modified = FALSE; 549 hw->eeprom_shadow_ram[i].eeprom_word = 0xFFFF; 550 } 551 } 552 553 hw->flash_base_addr = (flash_size & ICH_GFPREG_BASE_MASK) * 554 ICH_FLASH_SECTOR_SIZE; 555 556 hw->flash_bank_size = ((flash_size >> 16) 557 & ICH_GFPREG_BASE_MASK) + 1; 558 hw->flash_bank_size -= (flash_size & ICH_GFPREG_BASE_MASK); 559 560 hw->flash_bank_size *= ICH_FLASH_SECTOR_SIZE; 561 562 hw->flash_bank_size /= 2 * sizeof(uint16_t); 563 break; 564 } 565 #endif 566 default: 567 break; 568 } 569 570 if (eeprom->type == e1000_eeprom_spi) { 571 /* eeprom_size will be an enum [0..8] that maps 572 * to eeprom sizes 128B to 573 * 32KB (incremented by powers of 2). 574 */ 575 if (hw->mac_type <= e1000_82547_rev_2) { 576 /* Set to default value for initial eeprom read. */ 577 eeprom->word_size = 64; 578 ret_val = e1000_read_eeprom(hw, EEPROM_CFG, 1, 579 &eeprom_size); 580 if (ret_val) 581 return ret_val; 582 eeprom_size = (eeprom_size & EEPROM_SIZE_MASK) 583 >> EEPROM_SIZE_SHIFT; 584 /* 256B eeprom size was not supported in earlier 585 * hardware, so we bump eeprom_size up one to 586 * ensure that "1" (which maps to 256B) is never 587 * the result used in the shifting logic below. */ 588 if (eeprom_size) 589 eeprom_size++; 590 } else { 591 eeprom_size = (uint16_t)((eecd & 592 E1000_EECD_SIZE_EX_MASK) >> 593 E1000_EECD_SIZE_EX_SHIFT); 594 } 595 596 eeprom->word_size = 1 << (eeprom_size + EEPROM_WORD_SIZE_SHIFT); 597 } 598 return ret_val; 599 } 600 601 /****************************************************************************** 602 * Polls the status bit (bit 1) of the EERD to determine when the read is done. 603 * 604 * hw - Struct containing variables accessed by shared code 605 *****************************************************************************/ 606 static int32_t 607 e1000_poll_eerd_eewr_done(struct e1000_hw *hw, int eerd) 608 { 609 uint32_t attempts = 100000; 610 uint32_t i, reg = 0; 611 int32_t done = E1000_ERR_EEPROM; 612 613 for (i = 0; i < attempts; i++) { 614 if (eerd == E1000_EEPROM_POLL_READ) 615 reg = E1000_READ_REG(hw, EERD); 616 else 617 reg = E1000_READ_REG(hw, EEWR); 618 619 if (reg & E1000_EEPROM_RW_REG_DONE) { 620 done = E1000_SUCCESS; 621 break; 622 } 623 udelay(5); 624 } 625 626 return done; 627 } 628 629 /****************************************************************************** 630 * Reads a 16 bit word from the EEPROM using the EERD register. 631 * 632 * hw - Struct containing variables accessed by shared code 633 * offset - offset of word in the EEPROM to read 634 * data - word read from the EEPROM 635 * words - number of words to read 636 *****************************************************************************/ 637 static int32_t 638 e1000_read_eeprom_eerd(struct e1000_hw *hw, 639 uint16_t offset, 640 uint16_t words, 641 uint16_t *data) 642 { 643 uint32_t i, eerd = 0; 644 int32_t error = 0; 645 646 for (i = 0; i < words; i++) { 647 eerd = ((offset+i) << E1000_EEPROM_RW_ADDR_SHIFT) + 648 E1000_EEPROM_RW_REG_START; 649 650 E1000_WRITE_REG(hw, EERD, eerd); 651 error = e1000_poll_eerd_eewr_done(hw, E1000_EEPROM_POLL_READ); 652 653 if (error) 654 break; 655 data[i] = (E1000_READ_REG(hw, EERD) >> 656 E1000_EEPROM_RW_REG_DATA); 657 658 } 659 660 return error; 661 } 662 663 void e1000_release_eeprom(struct e1000_hw *hw) 664 { 665 uint32_t eecd; 666 667 DEBUGFUNC(); 668 669 eecd = E1000_READ_REG(hw, EECD); 670 671 if (hw->eeprom.type == e1000_eeprom_spi) { 672 eecd |= E1000_EECD_CS; /* Pull CS high */ 673 eecd &= ~E1000_EECD_SK; /* Lower SCK */ 674 675 E1000_WRITE_REG(hw, EECD, eecd); 676 677 udelay(hw->eeprom.delay_usec); 678 } else if (hw->eeprom.type == e1000_eeprom_microwire) { 679 /* cleanup eeprom */ 680 681 /* CS on Microwire is active-high */ 682 eecd &= ~(E1000_EECD_CS | E1000_EECD_DI); 683 684 E1000_WRITE_REG(hw, EECD, eecd); 685 686 /* Rising edge of clock */ 687 eecd |= E1000_EECD_SK; 688 E1000_WRITE_REG(hw, EECD, eecd); 689 E1000_WRITE_FLUSH(hw); 690 udelay(hw->eeprom.delay_usec); 691 692 /* Falling edge of clock */ 693 eecd &= ~E1000_EECD_SK; 694 E1000_WRITE_REG(hw, EECD, eecd); 695 E1000_WRITE_FLUSH(hw); 696 udelay(hw->eeprom.delay_usec); 697 } 698 699 /* Stop requesting EEPROM access */ 700 if (hw->mac_type > e1000_82544) { 701 eecd &= ~E1000_EECD_REQ; 702 E1000_WRITE_REG(hw, EECD, eecd); 703 } 704 } 705 /****************************************************************************** 706 * Reads a 16 bit word from the EEPROM. 707 * 708 * hw - Struct containing variables accessed by shared code 709 *****************************************************************************/ 710 static int32_t 711 e1000_spi_eeprom_ready(struct e1000_hw *hw) 712 { 713 uint16_t retry_count = 0; 714 uint8_t spi_stat_reg; 715 716 DEBUGFUNC(); 717 718 /* Read "Status Register" repeatedly until the LSB is cleared. The 719 * EEPROM will signal that the command has been completed by clearing 720 * bit 0 of the internal status register. If it's not cleared within 721 * 5 milliseconds, then error out. 722 */ 723 retry_count = 0; 724 do { 725 e1000_shift_out_ee_bits(hw, EEPROM_RDSR_OPCODE_SPI, 726 hw->eeprom.opcode_bits); 727 spi_stat_reg = (uint8_t)e1000_shift_in_ee_bits(hw, 8); 728 if (!(spi_stat_reg & EEPROM_STATUS_RDY_SPI)) 729 break; 730 731 udelay(5); 732 retry_count += 5; 733 734 e1000_standby_eeprom(hw); 735 } while (retry_count < EEPROM_MAX_RETRY_SPI); 736 737 /* ATMEL SPI write time could vary from 0-20mSec on 3.3V devices (and 738 * only 0-5mSec on 5V devices) 739 */ 740 if (retry_count >= EEPROM_MAX_RETRY_SPI) { 741 DEBUGOUT("SPI EEPROM Status error\n"); 742 return -E1000_ERR_EEPROM; 743 } 744 745 return E1000_SUCCESS; 746 } 747 748 /****************************************************************************** 749 * Reads a 16 bit word from the EEPROM. 750 * 751 * hw - Struct containing variables accessed by shared code 752 * offset - offset of word in the EEPROM to read 753 * data - word read from the EEPROM 754 *****************************************************************************/ 755 static int32_t 756 e1000_read_eeprom(struct e1000_hw *hw, uint16_t offset, 757 uint16_t words, uint16_t *data) 758 { 759 struct e1000_eeprom_info *eeprom = &hw->eeprom; 760 uint32_t i = 0; 761 762 DEBUGFUNC(); 763 764 /* If eeprom is not yet detected, do so now */ 765 if (eeprom->word_size == 0) 766 e1000_init_eeprom_params(hw); 767 768 /* A check for invalid values: offset too large, too many words, 769 * and not enough words. 770 */ 771 if ((offset >= eeprom->word_size) || 772 (words > eeprom->word_size - offset) || 773 (words == 0)) { 774 DEBUGOUT("\"words\" parameter out of bounds." 775 "Words = %d, size = %d\n", offset, eeprom->word_size); 776 return -E1000_ERR_EEPROM; 777 } 778 779 /* EEPROM's that don't use EERD to read require us to bit-bang the SPI 780 * directly. In this case, we need to acquire the EEPROM so that 781 * FW or other port software does not interrupt. 782 */ 783 if (e1000_is_onboard_nvm_eeprom(hw) == TRUE && 784 hw->eeprom.use_eerd == FALSE) { 785 786 /* Prepare the EEPROM for bit-bang reading */ 787 if (e1000_acquire_eeprom(hw) != E1000_SUCCESS) 788 return -E1000_ERR_EEPROM; 789 } 790 791 /* Eerd register EEPROM access requires no eeprom aquire/release */ 792 if (eeprom->use_eerd == TRUE) 793 return e1000_read_eeprom_eerd(hw, offset, words, data); 794 795 /* ich8lan does not support currently. if needed, please 796 * add corresponding code and functions. 797 */ 798 #if 0 799 /* ICH EEPROM access is done via the ICH flash controller */ 800 if (eeprom->type == e1000_eeprom_ich8) 801 return e1000_read_eeprom_ich8(hw, offset, words, data); 802 #endif 803 /* Set up the SPI or Microwire EEPROM for bit-bang reading. We have 804 * acquired the EEPROM at this point, so any returns should relase it */ 805 if (eeprom->type == e1000_eeprom_spi) { 806 uint16_t word_in; 807 uint8_t read_opcode = EEPROM_READ_OPCODE_SPI; 808 809 if (e1000_spi_eeprom_ready(hw)) { 810 e1000_release_eeprom(hw); 811 return -E1000_ERR_EEPROM; 812 } 813 814 e1000_standby_eeprom(hw); 815 816 /* Some SPI eeproms use the 8th address bit embedded in 817 * the opcode */ 818 if ((eeprom->address_bits == 8) && (offset >= 128)) 819 read_opcode |= EEPROM_A8_OPCODE_SPI; 820 821 /* Send the READ command (opcode + addr) */ 822 e1000_shift_out_ee_bits(hw, read_opcode, eeprom->opcode_bits); 823 e1000_shift_out_ee_bits(hw, (uint16_t)(offset*2), 824 eeprom->address_bits); 825 826 /* Read the data. The address of the eeprom internally 827 * increments with each byte (spi) being read, saving on the 828 * overhead of eeprom setup and tear-down. The address 829 * counter will roll over if reading beyond the size of 830 * the eeprom, thus allowing the entire memory to be read 831 * starting from any offset. */ 832 for (i = 0; i < words; i++) { 833 word_in = e1000_shift_in_ee_bits(hw, 16); 834 data[i] = (word_in >> 8) | (word_in << 8); 835 } 836 } else if (eeprom->type == e1000_eeprom_microwire) { 837 for (i = 0; i < words; i++) { 838 /* Send the READ command (opcode + addr) */ 839 e1000_shift_out_ee_bits(hw, 840 EEPROM_READ_OPCODE_MICROWIRE, 841 eeprom->opcode_bits); 842 e1000_shift_out_ee_bits(hw, (uint16_t)(offset + i), 843 eeprom->address_bits); 844 845 /* Read the data. For microwire, each word requires 846 * the overhead of eeprom setup and tear-down. */ 847 data[i] = e1000_shift_in_ee_bits(hw, 16); 848 e1000_standby_eeprom(hw); 849 } 850 } 851 852 /* End this read operation */ 853 e1000_release_eeprom(hw); 854 855 return E1000_SUCCESS; 856 } 857 858 /****************************************************************************** 859 * Verifies that the EEPROM has a valid checksum 860 * 861 * hw - Struct containing variables accessed by shared code 862 * 863 * Reads the first 64 16 bit words of the EEPROM and sums the values read. 864 * If the the sum of the 64 16 bit words is 0xBABA, the EEPROM's checksum is 865 * valid. 866 *****************************************************************************/ 867 static int e1000_validate_eeprom_checksum(struct e1000_hw *hw) 868 { 869 uint16_t i, checksum, checksum_reg, *buf; 870 871 DEBUGFUNC(); 872 873 /* Allocate a temporary buffer */ 874 buf = malloc(sizeof(buf[0]) * (EEPROM_CHECKSUM_REG + 1)); 875 if (!buf) { 876 E1000_ERR(hw->nic, "Unable to allocate EEPROM buffer!\n"); 877 return -E1000_ERR_EEPROM; 878 } 879 880 /* Read the EEPROM */ 881 if (e1000_read_eeprom(hw, 0, EEPROM_CHECKSUM_REG + 1, buf) < 0) { 882 E1000_ERR(hw->nic, "Unable to read EEPROM!\n"); 883 return -E1000_ERR_EEPROM; 884 } 885 886 /* Compute the checksum */ 887 checksum = 0; 888 for (i = 0; i < EEPROM_CHECKSUM_REG; i++) 889 checksum += buf[i]; 890 checksum = ((uint16_t)EEPROM_SUM) - checksum; 891 checksum_reg = buf[i]; 892 893 /* Verify it! */ 894 if (checksum == checksum_reg) 895 return 0; 896 897 /* Hrm, verification failed, print an error */ 898 E1000_ERR(hw->nic, "EEPROM checksum is incorrect!\n"); 899 E1000_ERR(hw->nic, " ...register was 0x%04hx, calculated 0x%04hx\n", 900 checksum_reg, checksum); 901 902 return -E1000_ERR_EEPROM; 903 } 904 905 /***************************************************************************** 906 * Set PHY to class A mode 907 * Assumes the following operations will follow to enable the new class mode. 908 * 1. Do a PHY soft reset 909 * 2. Restart auto-negotiation or force link. 910 * 911 * hw - Struct containing variables accessed by shared code 912 ****************************************************************************/ 913 static int32_t 914 e1000_set_phy_mode(struct e1000_hw *hw) 915 { 916 int32_t ret_val; 917 uint16_t eeprom_data; 918 919 DEBUGFUNC(); 920 921 if ((hw->mac_type == e1000_82545_rev_3) && 922 (hw->media_type == e1000_media_type_copper)) { 923 ret_val = e1000_read_eeprom(hw, EEPROM_PHY_CLASS_WORD, 924 1, &eeprom_data); 925 if (ret_val) 926 return ret_val; 927 928 if ((eeprom_data != EEPROM_RESERVED_WORD) && 929 (eeprom_data & EEPROM_PHY_CLASS_A)) { 930 ret_val = e1000_write_phy_reg(hw, 931 M88E1000_PHY_PAGE_SELECT, 0x000B); 932 if (ret_val) 933 return ret_val; 934 ret_val = e1000_write_phy_reg(hw, 935 M88E1000_PHY_GEN_CONTROL, 0x8104); 936 if (ret_val) 937 return ret_val; 938 939 hw->phy_reset_disable = FALSE; 940 } 941 } 942 943 return E1000_SUCCESS; 944 } 945 #endif /* #ifndef CONFIG_AP1000 */ 946 947 /*************************************************************************** 948 * 949 * Obtaining software semaphore bit (SMBI) before resetting PHY. 950 * 951 * hw: Struct containing variables accessed by shared code 952 * 953 * returns: - E1000_ERR_RESET if fail to obtain semaphore. 954 * E1000_SUCCESS at any other case. 955 * 956 ***************************************************************************/ 957 static int32_t 958 e1000_get_software_semaphore(struct e1000_hw *hw) 959 { 960 int32_t timeout = hw->eeprom.word_size + 1; 961 uint32_t swsm; 962 963 DEBUGFUNC(); 964 965 if (hw->mac_type != e1000_80003es2lan) 966 return E1000_SUCCESS; 967 968 while (timeout) { 969 swsm = E1000_READ_REG(hw, SWSM); 970 /* If SMBI bit cleared, it is now set and we hold 971 * the semaphore */ 972 if (!(swsm & E1000_SWSM_SMBI)) 973 break; 974 mdelay(1); 975 timeout--; 976 } 977 978 if (!timeout) { 979 DEBUGOUT("Driver can't access device - SMBI bit is set.\n"); 980 return -E1000_ERR_RESET; 981 } 982 983 return E1000_SUCCESS; 984 } 985 986 /*************************************************************************** 987 * This function clears HW semaphore bits. 988 * 989 * hw: Struct containing variables accessed by shared code 990 * 991 * returns: - None. 992 * 993 ***************************************************************************/ 994 static void 995 e1000_put_hw_eeprom_semaphore(struct e1000_hw *hw) 996 { 997 uint32_t swsm; 998 999 DEBUGFUNC(); 1000 1001 if (!hw->eeprom_semaphore_present) 1002 return; 1003 1004 swsm = E1000_READ_REG(hw, SWSM); 1005 if (hw->mac_type == e1000_80003es2lan) { 1006 /* Release both semaphores. */ 1007 swsm &= ~(E1000_SWSM_SMBI | E1000_SWSM_SWESMBI); 1008 } else 1009 swsm &= ~(E1000_SWSM_SWESMBI); 1010 E1000_WRITE_REG(hw, SWSM, swsm); 1011 } 1012 1013 /*************************************************************************** 1014 * 1015 * Using the combination of SMBI and SWESMBI semaphore bits when resetting 1016 * adapter or Eeprom access. 1017 * 1018 * hw: Struct containing variables accessed by shared code 1019 * 1020 * returns: - E1000_ERR_EEPROM if fail to access EEPROM. 1021 * E1000_SUCCESS at any other case. 1022 * 1023 ***************************************************************************/ 1024 static int32_t 1025 e1000_get_hw_eeprom_semaphore(struct e1000_hw *hw) 1026 { 1027 int32_t timeout; 1028 uint32_t swsm; 1029 1030 DEBUGFUNC(); 1031 1032 if (!hw->eeprom_semaphore_present) 1033 return E1000_SUCCESS; 1034 1035 if (hw->mac_type == e1000_80003es2lan) { 1036 /* Get the SW semaphore. */ 1037 if (e1000_get_software_semaphore(hw) != E1000_SUCCESS) 1038 return -E1000_ERR_EEPROM; 1039 } 1040 1041 /* Get the FW semaphore. */ 1042 timeout = hw->eeprom.word_size + 1; 1043 while (timeout) { 1044 swsm = E1000_READ_REG(hw, SWSM); 1045 swsm |= E1000_SWSM_SWESMBI; 1046 E1000_WRITE_REG(hw, SWSM, swsm); 1047 /* if we managed to set the bit we got the semaphore. */ 1048 swsm = E1000_READ_REG(hw, SWSM); 1049 if (swsm & E1000_SWSM_SWESMBI) 1050 break; 1051 1052 udelay(50); 1053 timeout--; 1054 } 1055 1056 if (!timeout) { 1057 /* Release semaphores */ 1058 e1000_put_hw_eeprom_semaphore(hw); 1059 DEBUGOUT("Driver can't access the Eeprom - " 1060 "SWESMBI bit is set.\n"); 1061 return -E1000_ERR_EEPROM; 1062 } 1063 1064 return E1000_SUCCESS; 1065 } 1066 1067 static int32_t 1068 e1000_swfw_sync_acquire(struct e1000_hw *hw, uint16_t mask) 1069 { 1070 uint32_t swfw_sync = 0; 1071 uint32_t swmask = mask; 1072 uint32_t fwmask = mask << 16; 1073 int32_t timeout = 200; 1074 1075 DEBUGFUNC(); 1076 while (timeout) { 1077 if (e1000_get_hw_eeprom_semaphore(hw)) 1078 return -E1000_ERR_SWFW_SYNC; 1079 1080 swfw_sync = E1000_READ_REG(hw, SW_FW_SYNC); 1081 if (!(swfw_sync & (fwmask | swmask))) 1082 break; 1083 1084 /* firmware currently using resource (fwmask) */ 1085 /* or other software thread currently using resource (swmask) */ 1086 e1000_put_hw_eeprom_semaphore(hw); 1087 mdelay(5); 1088 timeout--; 1089 } 1090 1091 if (!timeout) { 1092 DEBUGOUT("Driver can't access resource, SW_FW_SYNC timeout.\n"); 1093 return -E1000_ERR_SWFW_SYNC; 1094 } 1095 1096 swfw_sync |= swmask; 1097 E1000_WRITE_REG(hw, SW_FW_SYNC, swfw_sync); 1098 1099 e1000_put_hw_eeprom_semaphore(hw); 1100 return E1000_SUCCESS; 1101 } 1102 1103 static boolean_t e1000_is_second_port(struct e1000_hw *hw) 1104 { 1105 switch (hw->mac_type) { 1106 case e1000_80003es2lan: 1107 case e1000_82546: 1108 case e1000_82571: 1109 if (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1) 1110 return TRUE; 1111 /* Fallthrough */ 1112 default: 1113 return FALSE; 1114 } 1115 } 1116 1117 /****************************************************************************** 1118 * Reads the adapter's MAC address from the EEPROM and inverts the LSB for the 1119 * second function of dual function devices 1120 * 1121 * nic - Struct containing variables accessed by shared code 1122 *****************************************************************************/ 1123 static int 1124 e1000_read_mac_addr(struct eth_device *nic) 1125 { 1126 #ifndef CONFIG_AP1000 1127 struct e1000_hw *hw = nic->priv; 1128 uint16_t offset; 1129 uint16_t eeprom_data; 1130 int i; 1131 1132 DEBUGFUNC(); 1133 1134 for (i = 0; i < NODE_ADDRESS_SIZE; i += 2) { 1135 offset = i >> 1; 1136 if (e1000_read_eeprom(hw, offset, 1, &eeprom_data) < 0) { 1137 DEBUGOUT("EEPROM Read Error\n"); 1138 return -E1000_ERR_EEPROM; 1139 } 1140 nic->enetaddr[i] = eeprom_data & 0xff; 1141 nic->enetaddr[i + 1] = (eeprom_data >> 8) & 0xff; 1142 } 1143 1144 /* Invert the last bit if this is the second device */ 1145 if (e1000_is_second_port(hw)) 1146 nic->enetaddr[5] ^= 1; 1147 1148 #ifdef CONFIG_E1000_FALLBACK_MAC 1149 if (!is_valid_ether_addr(nic->enetaddr)) { 1150 unsigned char fb_mac[NODE_ADDRESS_SIZE] = CONFIG_E1000_FALLBACK_MAC; 1151 1152 memcpy (nic->enetaddr, fb_mac, NODE_ADDRESS_SIZE); 1153 } 1154 #endif 1155 #else 1156 /* 1157 * The AP1000's e1000 has no eeprom; the MAC address is stored in the 1158 * environment variables. Currently this does not support the addition 1159 * of a PMC e1000 card, which is certainly a possibility, so this should 1160 * be updated to properly use the env variable only for the onboard e1000 1161 */ 1162 1163 int ii; 1164 char *s, *e; 1165 1166 DEBUGFUNC(); 1167 1168 s = getenv ("ethaddr"); 1169 if (s == NULL) { 1170 return -E1000_ERR_EEPROM; 1171 } else { 1172 for(ii = 0; ii < 6; ii++) { 1173 nic->enetaddr[ii] = s ? simple_strtoul (s, &e, 16) : 0; 1174 if (s){ 1175 s = (*e) ? e + 1 : e; 1176 } 1177 } 1178 } 1179 #endif 1180 return 0; 1181 } 1182 1183 /****************************************************************************** 1184 * Initializes receive address filters. 1185 * 1186 * hw - Struct containing variables accessed by shared code 1187 * 1188 * Places the MAC address in receive address register 0 and clears the rest 1189 * of the receive addresss registers. Clears the multicast table. Assumes 1190 * the receiver is in reset when the routine is called. 1191 *****************************************************************************/ 1192 static void 1193 e1000_init_rx_addrs(struct eth_device *nic) 1194 { 1195 struct e1000_hw *hw = nic->priv; 1196 uint32_t i; 1197 uint32_t addr_low; 1198 uint32_t addr_high; 1199 1200 DEBUGFUNC(); 1201 1202 /* Setup the receive address. */ 1203 DEBUGOUT("Programming MAC Address into RAR[0]\n"); 1204 addr_low = (nic->enetaddr[0] | 1205 (nic->enetaddr[1] << 8) | 1206 (nic->enetaddr[2] << 16) | (nic->enetaddr[3] << 24)); 1207 1208 addr_high = (nic->enetaddr[4] | (nic->enetaddr[5] << 8) | E1000_RAH_AV); 1209 1210 E1000_WRITE_REG_ARRAY(hw, RA, 0, addr_low); 1211 E1000_WRITE_REG_ARRAY(hw, RA, 1, addr_high); 1212 1213 /* Zero out the other 15 receive addresses. */ 1214 DEBUGOUT("Clearing RAR[1-15]\n"); 1215 for (i = 1; i < E1000_RAR_ENTRIES; i++) { 1216 E1000_WRITE_REG_ARRAY(hw, RA, (i << 1), 0); 1217 E1000_WRITE_REG_ARRAY(hw, RA, ((i << 1) + 1), 0); 1218 } 1219 } 1220 1221 /****************************************************************************** 1222 * Clears the VLAN filer table 1223 * 1224 * hw - Struct containing variables accessed by shared code 1225 *****************************************************************************/ 1226 static void 1227 e1000_clear_vfta(struct e1000_hw *hw) 1228 { 1229 uint32_t offset; 1230 1231 for (offset = 0; offset < E1000_VLAN_FILTER_TBL_SIZE; offset++) 1232 E1000_WRITE_REG_ARRAY(hw, VFTA, offset, 0); 1233 } 1234 1235 /****************************************************************************** 1236 * Set the mac type member in the hw struct. 1237 * 1238 * hw - Struct containing variables accessed by shared code 1239 *****************************************************************************/ 1240 int32_t 1241 e1000_set_mac_type(struct e1000_hw *hw) 1242 { 1243 DEBUGFUNC(); 1244 1245 switch (hw->device_id) { 1246 case E1000_DEV_ID_82542: 1247 switch (hw->revision_id) { 1248 case E1000_82542_2_0_REV_ID: 1249 hw->mac_type = e1000_82542_rev2_0; 1250 break; 1251 case E1000_82542_2_1_REV_ID: 1252 hw->mac_type = e1000_82542_rev2_1; 1253 break; 1254 default: 1255 /* Invalid 82542 revision ID */ 1256 return -E1000_ERR_MAC_TYPE; 1257 } 1258 break; 1259 case E1000_DEV_ID_82543GC_FIBER: 1260 case E1000_DEV_ID_82543GC_COPPER: 1261 hw->mac_type = e1000_82543; 1262 break; 1263 case E1000_DEV_ID_82544EI_COPPER: 1264 case E1000_DEV_ID_82544EI_FIBER: 1265 case E1000_DEV_ID_82544GC_COPPER: 1266 case E1000_DEV_ID_82544GC_LOM: 1267 hw->mac_type = e1000_82544; 1268 break; 1269 case E1000_DEV_ID_82540EM: 1270 case E1000_DEV_ID_82540EM_LOM: 1271 case E1000_DEV_ID_82540EP: 1272 case E1000_DEV_ID_82540EP_LOM: 1273 case E1000_DEV_ID_82540EP_LP: 1274 hw->mac_type = e1000_82540; 1275 break; 1276 case E1000_DEV_ID_82545EM_COPPER: 1277 case E1000_DEV_ID_82545EM_FIBER: 1278 hw->mac_type = e1000_82545; 1279 break; 1280 case E1000_DEV_ID_82545GM_COPPER: 1281 case E1000_DEV_ID_82545GM_FIBER: 1282 case E1000_DEV_ID_82545GM_SERDES: 1283 hw->mac_type = e1000_82545_rev_3; 1284 break; 1285 case E1000_DEV_ID_82546EB_COPPER: 1286 case E1000_DEV_ID_82546EB_FIBER: 1287 case E1000_DEV_ID_82546EB_QUAD_COPPER: 1288 hw->mac_type = e1000_82546; 1289 break; 1290 case E1000_DEV_ID_82546GB_COPPER: 1291 case E1000_DEV_ID_82546GB_FIBER: 1292 case E1000_DEV_ID_82546GB_SERDES: 1293 case E1000_DEV_ID_82546GB_PCIE: 1294 case E1000_DEV_ID_82546GB_QUAD_COPPER: 1295 case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3: 1296 hw->mac_type = e1000_82546_rev_3; 1297 break; 1298 case E1000_DEV_ID_82541EI: 1299 case E1000_DEV_ID_82541EI_MOBILE: 1300 case E1000_DEV_ID_82541ER_LOM: 1301 hw->mac_type = e1000_82541; 1302 break; 1303 case E1000_DEV_ID_82541ER: 1304 case E1000_DEV_ID_82541GI: 1305 case E1000_DEV_ID_82541GI_LF: 1306 case E1000_DEV_ID_82541GI_MOBILE: 1307 hw->mac_type = e1000_82541_rev_2; 1308 break; 1309 case E1000_DEV_ID_82547EI: 1310 case E1000_DEV_ID_82547EI_MOBILE: 1311 hw->mac_type = e1000_82547; 1312 break; 1313 case E1000_DEV_ID_82547GI: 1314 hw->mac_type = e1000_82547_rev_2; 1315 break; 1316 case E1000_DEV_ID_82571EB_COPPER: 1317 case E1000_DEV_ID_82571EB_FIBER: 1318 case E1000_DEV_ID_82571EB_SERDES: 1319 case E1000_DEV_ID_82571EB_SERDES_DUAL: 1320 case E1000_DEV_ID_82571EB_SERDES_QUAD: 1321 case E1000_DEV_ID_82571EB_QUAD_COPPER: 1322 case E1000_DEV_ID_82571PT_QUAD_COPPER: 1323 case E1000_DEV_ID_82571EB_QUAD_FIBER: 1324 case E1000_DEV_ID_82571EB_QUAD_COPPER_LOWPROFILE: 1325 hw->mac_type = e1000_82571; 1326 break; 1327 case E1000_DEV_ID_82572EI_COPPER: 1328 case E1000_DEV_ID_82572EI_FIBER: 1329 case E1000_DEV_ID_82572EI_SERDES: 1330 case E1000_DEV_ID_82572EI: 1331 hw->mac_type = e1000_82572; 1332 break; 1333 case E1000_DEV_ID_82573E: 1334 case E1000_DEV_ID_82573E_IAMT: 1335 case E1000_DEV_ID_82573L: 1336 hw->mac_type = e1000_82573; 1337 break; 1338 case E1000_DEV_ID_82574L: 1339 hw->mac_type = e1000_82574; 1340 break; 1341 case E1000_DEV_ID_80003ES2LAN_COPPER_SPT: 1342 case E1000_DEV_ID_80003ES2LAN_SERDES_SPT: 1343 case E1000_DEV_ID_80003ES2LAN_COPPER_DPT: 1344 case E1000_DEV_ID_80003ES2LAN_SERDES_DPT: 1345 hw->mac_type = e1000_80003es2lan; 1346 break; 1347 case E1000_DEV_ID_ICH8_IGP_M_AMT: 1348 case E1000_DEV_ID_ICH8_IGP_AMT: 1349 case E1000_DEV_ID_ICH8_IGP_C: 1350 case E1000_DEV_ID_ICH8_IFE: 1351 case E1000_DEV_ID_ICH8_IFE_GT: 1352 case E1000_DEV_ID_ICH8_IFE_G: 1353 case E1000_DEV_ID_ICH8_IGP_M: 1354 hw->mac_type = e1000_ich8lan; 1355 break; 1356 default: 1357 /* Should never have loaded on this device */ 1358 return -E1000_ERR_MAC_TYPE; 1359 } 1360 return E1000_SUCCESS; 1361 } 1362 1363 /****************************************************************************** 1364 * Reset the transmit and receive units; mask and clear all interrupts. 1365 * 1366 * hw - Struct containing variables accessed by shared code 1367 *****************************************************************************/ 1368 void 1369 e1000_reset_hw(struct e1000_hw *hw) 1370 { 1371 uint32_t ctrl; 1372 uint32_t ctrl_ext; 1373 uint32_t manc; 1374 uint32_t pba = 0; 1375 1376 DEBUGFUNC(); 1377 1378 /* get the correct pba value for both PCI and PCIe*/ 1379 if (hw->mac_type < e1000_82571) 1380 pba = E1000_DEFAULT_PCI_PBA; 1381 else 1382 pba = E1000_DEFAULT_PCIE_PBA; 1383 1384 /* For 82542 (rev 2.0), disable MWI before issuing a device reset */ 1385 if (hw->mac_type == e1000_82542_rev2_0) { 1386 DEBUGOUT("Disabling MWI on 82542 rev 2.0\n"); 1387 pci_write_config_word(hw->pdev, PCI_COMMAND, 1388 hw->pci_cmd_word & ~PCI_COMMAND_INVALIDATE); 1389 } 1390 1391 /* Clear interrupt mask to stop board from generating interrupts */ 1392 DEBUGOUT("Masking off all interrupts\n"); 1393 E1000_WRITE_REG(hw, IMC, 0xffffffff); 1394 1395 /* Disable the Transmit and Receive units. Then delay to allow 1396 * any pending transactions to complete before we hit the MAC with 1397 * the global reset. 1398 */ 1399 E1000_WRITE_REG(hw, RCTL, 0); 1400 E1000_WRITE_REG(hw, TCTL, E1000_TCTL_PSP); 1401 E1000_WRITE_FLUSH(hw); 1402 1403 /* The tbi_compatibility_on Flag must be cleared when Rctl is cleared. */ 1404 hw->tbi_compatibility_on = FALSE; 1405 1406 /* Delay to allow any outstanding PCI transactions to complete before 1407 * resetting the device 1408 */ 1409 mdelay(10); 1410 1411 /* Issue a global reset to the MAC. This will reset the chip's 1412 * transmit, receive, DMA, and link units. It will not effect 1413 * the current PCI configuration. The global reset bit is self- 1414 * clearing, and should clear within a microsecond. 1415 */ 1416 DEBUGOUT("Issuing a global reset to MAC\n"); 1417 ctrl = E1000_READ_REG(hw, CTRL); 1418 1419 E1000_WRITE_REG(hw, CTRL, (ctrl | E1000_CTRL_RST)); 1420 1421 /* Force a reload from the EEPROM if necessary */ 1422 if (hw->mac_type < e1000_82540) { 1423 /* Wait for reset to complete */ 1424 udelay(10); 1425 ctrl_ext = E1000_READ_REG(hw, CTRL_EXT); 1426 ctrl_ext |= E1000_CTRL_EXT_EE_RST; 1427 E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext); 1428 E1000_WRITE_FLUSH(hw); 1429 /* Wait for EEPROM reload */ 1430 mdelay(2); 1431 } else { 1432 /* Wait for EEPROM reload (it happens automatically) */ 1433 mdelay(4); 1434 /* Dissable HW ARPs on ASF enabled adapters */ 1435 manc = E1000_READ_REG(hw, MANC); 1436 manc &= ~(E1000_MANC_ARP_EN); 1437 E1000_WRITE_REG(hw, MANC, manc); 1438 } 1439 1440 /* Clear interrupt mask to stop board from generating interrupts */ 1441 DEBUGOUT("Masking off all interrupts\n"); 1442 E1000_WRITE_REG(hw, IMC, 0xffffffff); 1443 1444 /* Clear any pending interrupt events. */ 1445 E1000_READ_REG(hw, ICR); 1446 1447 /* If MWI was previously enabled, reenable it. */ 1448 if (hw->mac_type == e1000_82542_rev2_0) { 1449 pci_write_config_word(hw->pdev, PCI_COMMAND, hw->pci_cmd_word); 1450 } 1451 E1000_WRITE_REG(hw, PBA, pba); 1452 } 1453 1454 /****************************************************************************** 1455 * 1456 * Initialize a number of hardware-dependent bits 1457 * 1458 * hw: Struct containing variables accessed by shared code 1459 * 1460 * This function contains hardware limitation workarounds for PCI-E adapters 1461 * 1462 *****************************************************************************/ 1463 static void 1464 e1000_initialize_hardware_bits(struct e1000_hw *hw) 1465 { 1466 if ((hw->mac_type >= e1000_82571) && 1467 (!hw->initialize_hw_bits_disable)) { 1468 /* Settings common to all PCI-express silicon */ 1469 uint32_t reg_ctrl, reg_ctrl_ext; 1470 uint32_t reg_tarc0, reg_tarc1; 1471 uint32_t reg_tctl; 1472 uint32_t reg_txdctl, reg_txdctl1; 1473 1474 /* link autonegotiation/sync workarounds */ 1475 reg_tarc0 = E1000_READ_REG(hw, TARC0); 1476 reg_tarc0 &= ~((1 << 30)|(1 << 29)|(1 << 28)|(1 << 27)); 1477 1478 /* Enable not-done TX descriptor counting */ 1479 reg_txdctl = E1000_READ_REG(hw, TXDCTL); 1480 reg_txdctl |= E1000_TXDCTL_COUNT_DESC; 1481 E1000_WRITE_REG(hw, TXDCTL, reg_txdctl); 1482 1483 reg_txdctl1 = E1000_READ_REG(hw, TXDCTL1); 1484 reg_txdctl1 |= E1000_TXDCTL_COUNT_DESC; 1485 E1000_WRITE_REG(hw, TXDCTL1, reg_txdctl1); 1486 1487 switch (hw->mac_type) { 1488 case e1000_82571: 1489 case e1000_82572: 1490 /* Clear PHY TX compatible mode bits */ 1491 reg_tarc1 = E1000_READ_REG(hw, TARC1); 1492 reg_tarc1 &= ~((1 << 30)|(1 << 29)); 1493 1494 /* link autonegotiation/sync workarounds */ 1495 reg_tarc0 |= ((1 << 26)|(1 << 25)|(1 << 24)|(1 << 23)); 1496 1497 /* TX ring control fixes */ 1498 reg_tarc1 |= ((1 << 26)|(1 << 25)|(1 << 24)); 1499 1500 /* Multiple read bit is reversed polarity */ 1501 reg_tctl = E1000_READ_REG(hw, TCTL); 1502 if (reg_tctl & E1000_TCTL_MULR) 1503 reg_tarc1 &= ~(1 << 28); 1504 else 1505 reg_tarc1 |= (1 << 28); 1506 1507 E1000_WRITE_REG(hw, TARC1, reg_tarc1); 1508 break; 1509 case e1000_82573: 1510 case e1000_82574: 1511 reg_ctrl_ext = E1000_READ_REG(hw, CTRL_EXT); 1512 reg_ctrl_ext &= ~(1 << 23); 1513 reg_ctrl_ext |= (1 << 22); 1514 1515 /* TX byte count fix */ 1516 reg_ctrl = E1000_READ_REG(hw, CTRL); 1517 reg_ctrl &= ~(1 << 29); 1518 1519 E1000_WRITE_REG(hw, CTRL_EXT, reg_ctrl_ext); 1520 E1000_WRITE_REG(hw, CTRL, reg_ctrl); 1521 break; 1522 case e1000_80003es2lan: 1523 /* improve small packet performace for fiber/serdes */ 1524 if ((hw->media_type == e1000_media_type_fiber) 1525 || (hw->media_type == 1526 e1000_media_type_internal_serdes)) { 1527 reg_tarc0 &= ~(1 << 20); 1528 } 1529 1530 /* Multiple read bit is reversed polarity */ 1531 reg_tctl = E1000_READ_REG(hw, TCTL); 1532 reg_tarc1 = E1000_READ_REG(hw, TARC1); 1533 if (reg_tctl & E1000_TCTL_MULR) 1534 reg_tarc1 &= ~(1 << 28); 1535 else 1536 reg_tarc1 |= (1 << 28); 1537 1538 E1000_WRITE_REG(hw, TARC1, reg_tarc1); 1539 break; 1540 case e1000_ich8lan: 1541 /* Reduce concurrent DMA requests to 3 from 4 */ 1542 if ((hw->revision_id < 3) || 1543 ((hw->device_id != E1000_DEV_ID_ICH8_IGP_M_AMT) && 1544 (hw->device_id != E1000_DEV_ID_ICH8_IGP_M))) 1545 reg_tarc0 |= ((1 << 29)|(1 << 28)); 1546 1547 reg_ctrl_ext = E1000_READ_REG(hw, CTRL_EXT); 1548 reg_ctrl_ext |= (1 << 22); 1549 E1000_WRITE_REG(hw, CTRL_EXT, reg_ctrl_ext); 1550 1551 /* workaround TX hang with TSO=on */ 1552 reg_tarc0 |= ((1 << 27)|(1 << 26)|(1 << 24)|(1 << 23)); 1553 1554 /* Multiple read bit is reversed polarity */ 1555 reg_tctl = E1000_READ_REG(hw, TCTL); 1556 reg_tarc1 = E1000_READ_REG(hw, TARC1); 1557 if (reg_tctl & E1000_TCTL_MULR) 1558 reg_tarc1 &= ~(1 << 28); 1559 else 1560 reg_tarc1 |= (1 << 28); 1561 1562 /* workaround TX hang with TSO=on */ 1563 reg_tarc1 |= ((1 << 30)|(1 << 26)|(1 << 24)); 1564 1565 E1000_WRITE_REG(hw, TARC1, reg_tarc1); 1566 break; 1567 default: 1568 break; 1569 } 1570 1571 E1000_WRITE_REG(hw, TARC0, reg_tarc0); 1572 } 1573 } 1574 1575 /****************************************************************************** 1576 * Performs basic configuration of the adapter. 1577 * 1578 * hw - Struct containing variables accessed by shared code 1579 * 1580 * Assumes that the controller has previously been reset and is in a 1581 * post-reset uninitialized state. Initializes the receive address registers, 1582 * multicast table, and VLAN filter table. Calls routines to setup link 1583 * configuration and flow control settings. Clears all on-chip counters. Leaves 1584 * the transmit and receive units disabled and uninitialized. 1585 *****************************************************************************/ 1586 static int 1587 e1000_init_hw(struct eth_device *nic) 1588 { 1589 struct e1000_hw *hw = nic->priv; 1590 uint32_t ctrl; 1591 uint32_t i; 1592 int32_t ret_val; 1593 uint16_t pcix_cmd_word; 1594 uint16_t pcix_stat_hi_word; 1595 uint16_t cmd_mmrbc; 1596 uint16_t stat_mmrbc; 1597 uint32_t mta_size; 1598 uint32_t reg_data; 1599 uint32_t ctrl_ext; 1600 DEBUGFUNC(); 1601 /* force full DMA clock frequency for 10/100 on ICH8 A0-B0 */ 1602 if ((hw->mac_type == e1000_ich8lan) && 1603 ((hw->revision_id < 3) || 1604 ((hw->device_id != E1000_DEV_ID_ICH8_IGP_M_AMT) && 1605 (hw->device_id != E1000_DEV_ID_ICH8_IGP_M)))) { 1606 reg_data = E1000_READ_REG(hw, STATUS); 1607 reg_data &= ~0x80000000; 1608 E1000_WRITE_REG(hw, STATUS, reg_data); 1609 } 1610 /* Do not need initialize Identification LED */ 1611 1612 /* Set the media type and TBI compatibility */ 1613 e1000_set_media_type(hw); 1614 1615 /* Must be called after e1000_set_media_type 1616 * because media_type is used */ 1617 e1000_initialize_hardware_bits(hw); 1618 1619 /* Disabling VLAN filtering. */ 1620 DEBUGOUT("Initializing the IEEE VLAN\n"); 1621 /* VET hardcoded to standard value and VFTA removed in ICH8 LAN */ 1622 if (hw->mac_type != e1000_ich8lan) { 1623 if (hw->mac_type < e1000_82545_rev_3) 1624 E1000_WRITE_REG(hw, VET, 0); 1625 e1000_clear_vfta(hw); 1626 } 1627 1628 /* For 82542 (rev 2.0), disable MWI and put the receiver into reset */ 1629 if (hw->mac_type == e1000_82542_rev2_0) { 1630 DEBUGOUT("Disabling MWI on 82542 rev 2.0\n"); 1631 pci_write_config_word(hw->pdev, PCI_COMMAND, 1632 hw-> 1633 pci_cmd_word & ~PCI_COMMAND_INVALIDATE); 1634 E1000_WRITE_REG(hw, RCTL, E1000_RCTL_RST); 1635 E1000_WRITE_FLUSH(hw); 1636 mdelay(5); 1637 } 1638 1639 /* Setup the receive address. This involves initializing all of the Receive 1640 * Address Registers (RARs 0 - 15). 1641 */ 1642 e1000_init_rx_addrs(nic); 1643 1644 /* For 82542 (rev 2.0), take the receiver out of reset and enable MWI */ 1645 if (hw->mac_type == e1000_82542_rev2_0) { 1646 E1000_WRITE_REG(hw, RCTL, 0); 1647 E1000_WRITE_FLUSH(hw); 1648 mdelay(1); 1649 pci_write_config_word(hw->pdev, PCI_COMMAND, hw->pci_cmd_word); 1650 } 1651 1652 /* Zero out the Multicast HASH table */ 1653 DEBUGOUT("Zeroing the MTA\n"); 1654 mta_size = E1000_MC_TBL_SIZE; 1655 if (hw->mac_type == e1000_ich8lan) 1656 mta_size = E1000_MC_TBL_SIZE_ICH8LAN; 1657 for (i = 0; i < mta_size; i++) { 1658 E1000_WRITE_REG_ARRAY(hw, MTA, i, 0); 1659 /* use write flush to prevent Memory Write Block (MWB) from 1660 * occuring when accessing our register space */ 1661 E1000_WRITE_FLUSH(hw); 1662 } 1663 #if 0 1664 /* Set the PCI priority bit correctly in the CTRL register. This 1665 * determines if the adapter gives priority to receives, or if it 1666 * gives equal priority to transmits and receives. Valid only on 1667 * 82542 and 82543 silicon. 1668 */ 1669 if (hw->dma_fairness && hw->mac_type <= e1000_82543) { 1670 ctrl = E1000_READ_REG(hw, CTRL); 1671 E1000_WRITE_REG(hw, CTRL, ctrl | E1000_CTRL_PRIOR); 1672 } 1673 #endif 1674 switch (hw->mac_type) { 1675 case e1000_82545_rev_3: 1676 case e1000_82546_rev_3: 1677 break; 1678 default: 1679 /* Workaround for PCI-X problem when BIOS sets MMRBC incorrectly. */ 1680 if (hw->bus_type == e1000_bus_type_pcix) { 1681 pci_read_config_word(hw->pdev, PCIX_COMMAND_REGISTER, 1682 &pcix_cmd_word); 1683 pci_read_config_word(hw->pdev, PCIX_STATUS_REGISTER_HI, 1684 &pcix_stat_hi_word); 1685 cmd_mmrbc = 1686 (pcix_cmd_word & PCIX_COMMAND_MMRBC_MASK) >> 1687 PCIX_COMMAND_MMRBC_SHIFT; 1688 stat_mmrbc = 1689 (pcix_stat_hi_word & PCIX_STATUS_HI_MMRBC_MASK) >> 1690 PCIX_STATUS_HI_MMRBC_SHIFT; 1691 if (stat_mmrbc == PCIX_STATUS_HI_MMRBC_4K) 1692 stat_mmrbc = PCIX_STATUS_HI_MMRBC_2K; 1693 if (cmd_mmrbc > stat_mmrbc) { 1694 pcix_cmd_word &= ~PCIX_COMMAND_MMRBC_MASK; 1695 pcix_cmd_word |= stat_mmrbc << PCIX_COMMAND_MMRBC_SHIFT; 1696 pci_write_config_word(hw->pdev, PCIX_COMMAND_REGISTER, 1697 pcix_cmd_word); 1698 } 1699 } 1700 break; 1701 } 1702 1703 /* More time needed for PHY to initialize */ 1704 if (hw->mac_type == e1000_ich8lan) 1705 mdelay(15); 1706 1707 /* Call a subroutine to configure the link and setup flow control. */ 1708 ret_val = e1000_setup_link(nic); 1709 1710 /* Set the transmit descriptor write-back policy */ 1711 if (hw->mac_type > e1000_82544) { 1712 ctrl = E1000_READ_REG(hw, TXDCTL); 1713 ctrl = 1714 (ctrl & ~E1000_TXDCTL_WTHRESH) | 1715 E1000_TXDCTL_FULL_TX_DESC_WB; 1716 E1000_WRITE_REG(hw, TXDCTL, ctrl); 1717 } 1718 1719 switch (hw->mac_type) { 1720 default: 1721 break; 1722 case e1000_80003es2lan: 1723 /* Enable retransmit on late collisions */ 1724 reg_data = E1000_READ_REG(hw, TCTL); 1725 reg_data |= E1000_TCTL_RTLC; 1726 E1000_WRITE_REG(hw, TCTL, reg_data); 1727 1728 /* Configure Gigabit Carry Extend Padding */ 1729 reg_data = E1000_READ_REG(hw, TCTL_EXT); 1730 reg_data &= ~E1000_TCTL_EXT_GCEX_MASK; 1731 reg_data |= DEFAULT_80003ES2LAN_TCTL_EXT_GCEX; 1732 E1000_WRITE_REG(hw, TCTL_EXT, reg_data); 1733 1734 /* Configure Transmit Inter-Packet Gap */ 1735 reg_data = E1000_READ_REG(hw, TIPG); 1736 reg_data &= ~E1000_TIPG_IPGT_MASK; 1737 reg_data |= DEFAULT_80003ES2LAN_TIPG_IPGT_1000; 1738 E1000_WRITE_REG(hw, TIPG, reg_data); 1739 1740 reg_data = E1000_READ_REG_ARRAY(hw, FFLT, 0x0001); 1741 reg_data &= ~0x00100000; 1742 E1000_WRITE_REG_ARRAY(hw, FFLT, 0x0001, reg_data); 1743 /* Fall through */ 1744 case e1000_82571: 1745 case e1000_82572: 1746 case e1000_ich8lan: 1747 ctrl = E1000_READ_REG(hw, TXDCTL1); 1748 ctrl = (ctrl & ~E1000_TXDCTL_WTHRESH) 1749 | E1000_TXDCTL_FULL_TX_DESC_WB; 1750 E1000_WRITE_REG(hw, TXDCTL1, ctrl); 1751 break; 1752 case e1000_82573: 1753 case e1000_82574: 1754 reg_data = E1000_READ_REG(hw, GCR); 1755 reg_data |= E1000_GCR_L1_ACT_WITHOUT_L0S_RX; 1756 E1000_WRITE_REG(hw, GCR, reg_data); 1757 } 1758 1759 #if 0 1760 /* Clear all of the statistics registers (clear on read). It is 1761 * important that we do this after we have tried to establish link 1762 * because the symbol error count will increment wildly if there 1763 * is no link. 1764 */ 1765 e1000_clear_hw_cntrs(hw); 1766 1767 /* ICH8 No-snoop bits are opposite polarity. 1768 * Set to snoop by default after reset. */ 1769 if (hw->mac_type == e1000_ich8lan) 1770 e1000_set_pci_ex_no_snoop(hw, PCI_EX_82566_SNOOP_ALL); 1771 #endif 1772 1773 if (hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER || 1774 hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3) { 1775 ctrl_ext = E1000_READ_REG(hw, CTRL_EXT); 1776 /* Relaxed ordering must be disabled to avoid a parity 1777 * error crash in a PCI slot. */ 1778 ctrl_ext |= E1000_CTRL_EXT_RO_DIS; 1779 E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext); 1780 } 1781 1782 return ret_val; 1783 } 1784 1785 /****************************************************************************** 1786 * Configures flow control and link settings. 1787 * 1788 * hw - Struct containing variables accessed by shared code 1789 * 1790 * Determines which flow control settings to use. Calls the apropriate media- 1791 * specific link configuration function. Configures the flow control settings. 1792 * Assuming the adapter has a valid link partner, a valid link should be 1793 * established. Assumes the hardware has previously been reset and the 1794 * transmitter and receiver are not enabled. 1795 *****************************************************************************/ 1796 static int 1797 e1000_setup_link(struct eth_device *nic) 1798 { 1799 struct e1000_hw *hw = nic->priv; 1800 uint32_t ctrl_ext; 1801 int32_t ret_val; 1802 uint16_t eeprom_data; 1803 1804 DEBUGFUNC(); 1805 1806 /* In the case of the phy reset being blocked, we already have a link. 1807 * We do not have to set it up again. */ 1808 if (e1000_check_phy_reset_block(hw)) 1809 return E1000_SUCCESS; 1810 1811 #ifndef CONFIG_AP1000 1812 /* Read and store word 0x0F of the EEPROM. This word contains bits 1813 * that determine the hardware's default PAUSE (flow control) mode, 1814 * a bit that determines whether the HW defaults to enabling or 1815 * disabling auto-negotiation, and the direction of the 1816 * SW defined pins. If there is no SW over-ride of the flow 1817 * control setting, then the variable hw->fc will 1818 * be initialized based on a value in the EEPROM. 1819 */ 1820 if (e1000_read_eeprom(hw, EEPROM_INIT_CONTROL2_REG, 1, 1821 &eeprom_data) < 0) { 1822 DEBUGOUT("EEPROM Read Error\n"); 1823 return -E1000_ERR_EEPROM; 1824 } 1825 #else 1826 /* we have to hardcode the proper value for our hardware. */ 1827 /* this value is for the 82540EM pci card used for prototyping, and it works. */ 1828 eeprom_data = 0xb220; 1829 #endif 1830 1831 if (hw->fc == e1000_fc_default) { 1832 switch (hw->mac_type) { 1833 case e1000_ich8lan: 1834 case e1000_82573: 1835 case e1000_82574: 1836 hw->fc = e1000_fc_full; 1837 break; 1838 default: 1839 #ifndef CONFIG_AP1000 1840 ret_val = e1000_read_eeprom(hw, 1841 EEPROM_INIT_CONTROL2_REG, 1, &eeprom_data); 1842 if (ret_val) { 1843 DEBUGOUT("EEPROM Read Error\n"); 1844 return -E1000_ERR_EEPROM; 1845 } 1846 #else 1847 eeprom_data = 0xb220; 1848 #endif 1849 if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) == 0) 1850 hw->fc = e1000_fc_none; 1851 else if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) == 1852 EEPROM_WORD0F_ASM_DIR) 1853 hw->fc = e1000_fc_tx_pause; 1854 else 1855 hw->fc = e1000_fc_full; 1856 break; 1857 } 1858 } 1859 1860 /* We want to save off the original Flow Control configuration just 1861 * in case we get disconnected and then reconnected into a different 1862 * hub or switch with different Flow Control capabilities. 1863 */ 1864 if (hw->mac_type == e1000_82542_rev2_0) 1865 hw->fc &= (~e1000_fc_tx_pause); 1866 1867 if ((hw->mac_type < e1000_82543) && (hw->report_tx_early == 1)) 1868 hw->fc &= (~e1000_fc_rx_pause); 1869 1870 hw->original_fc = hw->fc; 1871 1872 DEBUGOUT("After fix-ups FlowControl is now = %x\n", hw->fc); 1873 1874 /* Take the 4 bits from EEPROM word 0x0F that determine the initial 1875 * polarity value for the SW controlled pins, and setup the 1876 * Extended Device Control reg with that info. 1877 * This is needed because one of the SW controlled pins is used for 1878 * signal detection. So this should be done before e1000_setup_pcs_link() 1879 * or e1000_phy_setup() is called. 1880 */ 1881 if (hw->mac_type == e1000_82543) { 1882 ctrl_ext = ((eeprom_data & EEPROM_WORD0F_SWPDIO_EXT) << 1883 SWDPIO__EXT_SHIFT); 1884 E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext); 1885 } 1886 1887 /* Call the necessary subroutine to configure the link. */ 1888 ret_val = (hw->media_type == e1000_media_type_fiber) ? 1889 e1000_setup_fiber_link(nic) : e1000_setup_copper_link(nic); 1890 if (ret_val < 0) { 1891 return ret_val; 1892 } 1893 1894 /* Initialize the flow control address, type, and PAUSE timer 1895 * registers to their default values. This is done even if flow 1896 * control is disabled, because it does not hurt anything to 1897 * initialize these registers. 1898 */ 1899 DEBUGOUT("Initializing the Flow Control address, type" 1900 "and timer regs\n"); 1901 1902 /* FCAL/H and FCT are hardcoded to standard values in e1000_ich8lan. */ 1903 if (hw->mac_type != e1000_ich8lan) { 1904 E1000_WRITE_REG(hw, FCT, FLOW_CONTROL_TYPE); 1905 E1000_WRITE_REG(hw, FCAH, FLOW_CONTROL_ADDRESS_HIGH); 1906 E1000_WRITE_REG(hw, FCAL, FLOW_CONTROL_ADDRESS_LOW); 1907 } 1908 1909 E1000_WRITE_REG(hw, FCTTV, hw->fc_pause_time); 1910 1911 /* Set the flow control receive threshold registers. Normally, 1912 * these registers will be set to a default threshold that may be 1913 * adjusted later by the driver's runtime code. However, if the 1914 * ability to transmit pause frames in not enabled, then these 1915 * registers will be set to 0. 1916 */ 1917 if (!(hw->fc & e1000_fc_tx_pause)) { 1918 E1000_WRITE_REG(hw, FCRTL, 0); 1919 E1000_WRITE_REG(hw, FCRTH, 0); 1920 } else { 1921 /* We need to set up the Receive Threshold high and low water marks 1922 * as well as (optionally) enabling the transmission of XON frames. 1923 */ 1924 if (hw->fc_send_xon) { 1925 E1000_WRITE_REG(hw, FCRTL, 1926 (hw->fc_low_water | E1000_FCRTL_XONE)); 1927 E1000_WRITE_REG(hw, FCRTH, hw->fc_high_water); 1928 } else { 1929 E1000_WRITE_REG(hw, FCRTL, hw->fc_low_water); 1930 E1000_WRITE_REG(hw, FCRTH, hw->fc_high_water); 1931 } 1932 } 1933 return ret_val; 1934 } 1935 1936 /****************************************************************************** 1937 * Sets up link for a fiber based adapter 1938 * 1939 * hw - Struct containing variables accessed by shared code 1940 * 1941 * Manipulates Physical Coding Sublayer functions in order to configure 1942 * link. Assumes the hardware has been previously reset and the transmitter 1943 * and receiver are not enabled. 1944 *****************************************************************************/ 1945 static int 1946 e1000_setup_fiber_link(struct eth_device *nic) 1947 { 1948 struct e1000_hw *hw = nic->priv; 1949 uint32_t ctrl; 1950 uint32_t status; 1951 uint32_t txcw = 0; 1952 uint32_t i; 1953 uint32_t signal; 1954 int32_t ret_val; 1955 1956 DEBUGFUNC(); 1957 /* On adapters with a MAC newer that 82544, SW Defineable pin 1 will be 1958 * set when the optics detect a signal. On older adapters, it will be 1959 * cleared when there is a signal 1960 */ 1961 ctrl = E1000_READ_REG(hw, CTRL); 1962 if ((hw->mac_type > e1000_82544) && !(ctrl & E1000_CTRL_ILOS)) 1963 signal = E1000_CTRL_SWDPIN1; 1964 else 1965 signal = 0; 1966 1967 printf("signal for %s is %x (ctrl %08x)!!!!\n", nic->name, signal, 1968 ctrl); 1969 /* Take the link out of reset */ 1970 ctrl &= ~(E1000_CTRL_LRST); 1971 1972 e1000_config_collision_dist(hw); 1973 1974 /* Check for a software override of the flow control settings, and setup 1975 * the device accordingly. If auto-negotiation is enabled, then software 1976 * will have to set the "PAUSE" bits to the correct value in the Tranmsit 1977 * Config Word Register (TXCW) and re-start auto-negotiation. However, if 1978 * auto-negotiation is disabled, then software will have to manually 1979 * configure the two flow control enable bits in the CTRL register. 1980 * 1981 * The possible values of the "fc" parameter are: 1982 * 0: Flow control is completely disabled 1983 * 1: Rx flow control is enabled (we can receive pause frames, but 1984 * not send pause frames). 1985 * 2: Tx flow control is enabled (we can send pause frames but we do 1986 * not support receiving pause frames). 1987 * 3: Both Rx and TX flow control (symmetric) are enabled. 1988 */ 1989 switch (hw->fc) { 1990 case e1000_fc_none: 1991 /* Flow control is completely disabled by a software over-ride. */ 1992 txcw = (E1000_TXCW_ANE | E1000_TXCW_FD); 1993 break; 1994 case e1000_fc_rx_pause: 1995 /* RX Flow control is enabled and TX Flow control is disabled by a 1996 * software over-ride. Since there really isn't a way to advertise 1997 * that we are capable of RX Pause ONLY, we will advertise that we 1998 * support both symmetric and asymmetric RX PAUSE. Later, we will 1999 * disable the adapter's ability to send PAUSE frames. 2000 */ 2001 txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK); 2002 break; 2003 case e1000_fc_tx_pause: 2004 /* TX Flow control is enabled, and RX Flow control is disabled, by a 2005 * software over-ride. 2006 */ 2007 txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_ASM_DIR); 2008 break; 2009 case e1000_fc_full: 2010 /* Flow control (both RX and TX) is enabled by a software over-ride. */ 2011 txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK); 2012 break; 2013 default: 2014 DEBUGOUT("Flow control param set incorrectly\n"); 2015 return -E1000_ERR_CONFIG; 2016 break; 2017 } 2018 2019 /* Since auto-negotiation is enabled, take the link out of reset (the link 2020 * will be in reset, because we previously reset the chip). This will 2021 * restart auto-negotiation. If auto-neogtiation is successful then the 2022 * link-up status bit will be set and the flow control enable bits (RFCE 2023 * and TFCE) will be set according to their negotiated value. 2024 */ 2025 DEBUGOUT("Auto-negotiation enabled (%#x)\n", txcw); 2026 2027 E1000_WRITE_REG(hw, TXCW, txcw); 2028 E1000_WRITE_REG(hw, CTRL, ctrl); 2029 E1000_WRITE_FLUSH(hw); 2030 2031 hw->txcw = txcw; 2032 mdelay(1); 2033 2034 /* If we have a signal (the cable is plugged in) then poll for a "Link-Up" 2035 * indication in the Device Status Register. Time-out if a link isn't 2036 * seen in 500 milliseconds seconds (Auto-negotiation should complete in 2037 * less than 500 milliseconds even if the other end is doing it in SW). 2038 */ 2039 if ((E1000_READ_REG(hw, CTRL) & E1000_CTRL_SWDPIN1) == signal) { 2040 DEBUGOUT("Looking for Link\n"); 2041 for (i = 0; i < (LINK_UP_TIMEOUT / 10); i++) { 2042 mdelay(10); 2043 status = E1000_READ_REG(hw, STATUS); 2044 if (status & E1000_STATUS_LU) 2045 break; 2046 } 2047 if (i == (LINK_UP_TIMEOUT / 10)) { 2048 /* AutoNeg failed to achieve a link, so we'll call 2049 * e1000_check_for_link. This routine will force the link up if we 2050 * detect a signal. This will allow us to communicate with 2051 * non-autonegotiating link partners. 2052 */ 2053 DEBUGOUT("Never got a valid link from auto-neg!!!\n"); 2054 hw->autoneg_failed = 1; 2055 ret_val = e1000_check_for_link(nic); 2056 if (ret_val < 0) { 2057 DEBUGOUT("Error while checking for link\n"); 2058 return ret_val; 2059 } 2060 hw->autoneg_failed = 0; 2061 } else { 2062 hw->autoneg_failed = 0; 2063 DEBUGOUT("Valid Link Found\n"); 2064 } 2065 } else { 2066 DEBUGOUT("No Signal Detected\n"); 2067 return -E1000_ERR_NOLINK; 2068 } 2069 return 0; 2070 } 2071 2072 /****************************************************************************** 2073 * Make sure we have a valid PHY and change PHY mode before link setup. 2074 * 2075 * hw - Struct containing variables accessed by shared code 2076 ******************************************************************************/ 2077 static int32_t 2078 e1000_copper_link_preconfig(struct e1000_hw *hw) 2079 { 2080 uint32_t ctrl; 2081 int32_t ret_val; 2082 uint16_t phy_data; 2083 2084 DEBUGFUNC(); 2085 2086 ctrl = E1000_READ_REG(hw, CTRL); 2087 /* With 82543, we need to force speed and duplex on the MAC equal to what 2088 * the PHY speed and duplex configuration is. In addition, we need to 2089 * perform a hardware reset on the PHY to take it out of reset. 2090 */ 2091 if (hw->mac_type > e1000_82543) { 2092 ctrl |= E1000_CTRL_SLU; 2093 ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); 2094 E1000_WRITE_REG(hw, CTRL, ctrl); 2095 } else { 2096 ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX 2097 | E1000_CTRL_SLU); 2098 E1000_WRITE_REG(hw, CTRL, ctrl); 2099 ret_val = e1000_phy_hw_reset(hw); 2100 if (ret_val) 2101 return ret_val; 2102 } 2103 2104 /* Make sure we have a valid PHY */ 2105 ret_val = e1000_detect_gig_phy(hw); 2106 if (ret_val) { 2107 DEBUGOUT("Error, did not detect valid phy.\n"); 2108 return ret_val; 2109 } 2110 DEBUGOUT("Phy ID = %x \n", hw->phy_id); 2111 2112 #ifndef CONFIG_AP1000 2113 /* Set PHY to class A mode (if necessary) */ 2114 ret_val = e1000_set_phy_mode(hw); 2115 if (ret_val) 2116 return ret_val; 2117 #endif 2118 if ((hw->mac_type == e1000_82545_rev_3) || 2119 (hw->mac_type == e1000_82546_rev_3)) { 2120 ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, 2121 &phy_data); 2122 phy_data |= 0x00000008; 2123 ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, 2124 phy_data); 2125 } 2126 2127 if (hw->mac_type <= e1000_82543 || 2128 hw->mac_type == e1000_82541 || hw->mac_type == e1000_82547 || 2129 hw->mac_type == e1000_82541_rev_2 2130 || hw->mac_type == e1000_82547_rev_2) 2131 hw->phy_reset_disable = FALSE; 2132 2133 return E1000_SUCCESS; 2134 } 2135 2136 /***************************************************************************** 2137 * 2138 * This function sets the lplu state according to the active flag. When 2139 * activating lplu this function also disables smart speed and vise versa. 2140 * lplu will not be activated unless the device autonegotiation advertisment 2141 * meets standards of either 10 or 10/100 or 10/100/1000 at all duplexes. 2142 * hw: Struct containing variables accessed by shared code 2143 * active - true to enable lplu false to disable lplu. 2144 * 2145 * returns: - E1000_ERR_PHY if fail to read/write the PHY 2146 * E1000_SUCCESS at any other case. 2147 * 2148 ****************************************************************************/ 2149 2150 static int32_t 2151 e1000_set_d3_lplu_state(struct e1000_hw *hw, boolean_t active) 2152 { 2153 uint32_t phy_ctrl = 0; 2154 int32_t ret_val; 2155 uint16_t phy_data; 2156 DEBUGFUNC(); 2157 2158 if (hw->phy_type != e1000_phy_igp && hw->phy_type != e1000_phy_igp_2 2159 && hw->phy_type != e1000_phy_igp_3) 2160 return E1000_SUCCESS; 2161 2162 /* During driver activity LPLU should not be used or it will attain link 2163 * from the lowest speeds starting from 10Mbps. The capability is used 2164 * for Dx transitions and states */ 2165 if (hw->mac_type == e1000_82541_rev_2 2166 || hw->mac_type == e1000_82547_rev_2) { 2167 ret_val = e1000_read_phy_reg(hw, IGP01E1000_GMII_FIFO, 2168 &phy_data); 2169 if (ret_val) 2170 return ret_val; 2171 } else if (hw->mac_type == e1000_ich8lan) { 2172 /* MAC writes into PHY register based on the state transition 2173 * and start auto-negotiation. SW driver can overwrite the 2174 * settings in CSR PHY power control E1000_PHY_CTRL register. */ 2175 phy_ctrl = E1000_READ_REG(hw, PHY_CTRL); 2176 } else { 2177 ret_val = e1000_read_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, 2178 &phy_data); 2179 if (ret_val) 2180 return ret_val; 2181 } 2182 2183 if (!active) { 2184 if (hw->mac_type == e1000_82541_rev_2 || 2185 hw->mac_type == e1000_82547_rev_2) { 2186 phy_data &= ~IGP01E1000_GMII_FLEX_SPD; 2187 ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO, 2188 phy_data); 2189 if (ret_val) 2190 return ret_val; 2191 } else { 2192 if (hw->mac_type == e1000_ich8lan) { 2193 phy_ctrl &= ~E1000_PHY_CTRL_NOND0A_LPLU; 2194 E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl); 2195 } else { 2196 phy_data &= ~IGP02E1000_PM_D3_LPLU; 2197 ret_val = e1000_write_phy_reg(hw, 2198 IGP02E1000_PHY_POWER_MGMT, phy_data); 2199 if (ret_val) 2200 return ret_val; 2201 } 2202 } 2203 2204 /* LPLU and SmartSpeed are mutually exclusive. LPLU is used during 2205 * Dx states where the power conservation is most important. During 2206 * driver activity we should enable SmartSpeed, so performance is 2207 * maintained. */ 2208 if (hw->smart_speed == e1000_smart_speed_on) { 2209 ret_val = e1000_read_phy_reg(hw, 2210 IGP01E1000_PHY_PORT_CONFIG, &phy_data); 2211 if (ret_val) 2212 return ret_val; 2213 2214 phy_data |= IGP01E1000_PSCFR_SMART_SPEED; 2215 ret_val = e1000_write_phy_reg(hw, 2216 IGP01E1000_PHY_PORT_CONFIG, phy_data); 2217 if (ret_val) 2218 return ret_val; 2219 } else if (hw->smart_speed == e1000_smart_speed_off) { 2220 ret_val = e1000_read_phy_reg(hw, 2221 IGP01E1000_PHY_PORT_CONFIG, &phy_data); 2222 if (ret_val) 2223 return ret_val; 2224 2225 phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED; 2226 ret_val = e1000_write_phy_reg(hw, 2227 IGP01E1000_PHY_PORT_CONFIG, phy_data); 2228 if (ret_val) 2229 return ret_val; 2230 } 2231 2232 } else if ((hw->autoneg_advertised == AUTONEG_ADVERTISE_SPEED_DEFAULT) 2233 || (hw->autoneg_advertised == AUTONEG_ADVERTISE_10_ALL) || 2234 (hw->autoneg_advertised == AUTONEG_ADVERTISE_10_100_ALL)) { 2235 2236 if (hw->mac_type == e1000_82541_rev_2 || 2237 hw->mac_type == e1000_82547_rev_2) { 2238 phy_data |= IGP01E1000_GMII_FLEX_SPD; 2239 ret_val = e1000_write_phy_reg(hw, 2240 IGP01E1000_GMII_FIFO, phy_data); 2241 if (ret_val) 2242 return ret_val; 2243 } else { 2244 if (hw->mac_type == e1000_ich8lan) { 2245 phy_ctrl |= E1000_PHY_CTRL_NOND0A_LPLU; 2246 E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl); 2247 } else { 2248 phy_data |= IGP02E1000_PM_D3_LPLU; 2249 ret_val = e1000_write_phy_reg(hw, 2250 IGP02E1000_PHY_POWER_MGMT, phy_data); 2251 if (ret_val) 2252 return ret_val; 2253 } 2254 } 2255 2256 /* When LPLU is enabled we should disable SmartSpeed */ 2257 ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, 2258 &phy_data); 2259 if (ret_val) 2260 return ret_val; 2261 2262 phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED; 2263 ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, 2264 phy_data); 2265 if (ret_val) 2266 return ret_val; 2267 } 2268 return E1000_SUCCESS; 2269 } 2270 2271 /***************************************************************************** 2272 * 2273 * This function sets the lplu d0 state according to the active flag. When 2274 * activating lplu this function also disables smart speed and vise versa. 2275 * lplu will not be activated unless the device autonegotiation advertisment 2276 * meets standards of either 10 or 10/100 or 10/100/1000 at all duplexes. 2277 * hw: Struct containing variables accessed by shared code 2278 * active - true to enable lplu false to disable lplu. 2279 * 2280 * returns: - E1000_ERR_PHY if fail to read/write the PHY 2281 * E1000_SUCCESS at any other case. 2282 * 2283 ****************************************************************************/ 2284 2285 static int32_t 2286 e1000_set_d0_lplu_state(struct e1000_hw *hw, boolean_t active) 2287 { 2288 uint32_t phy_ctrl = 0; 2289 int32_t ret_val; 2290 uint16_t phy_data; 2291 DEBUGFUNC(); 2292 2293 if (hw->mac_type <= e1000_82547_rev_2) 2294 return E1000_SUCCESS; 2295 2296 if (hw->mac_type == e1000_ich8lan) { 2297 phy_ctrl = E1000_READ_REG(hw, PHY_CTRL); 2298 } else { 2299 ret_val = e1000_read_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, 2300 &phy_data); 2301 if (ret_val) 2302 return ret_val; 2303 } 2304 2305 if (!active) { 2306 if (hw->mac_type == e1000_ich8lan) { 2307 phy_ctrl &= ~E1000_PHY_CTRL_D0A_LPLU; 2308 E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl); 2309 } else { 2310 phy_data &= ~IGP02E1000_PM_D0_LPLU; 2311 ret_val = e1000_write_phy_reg(hw, 2312 IGP02E1000_PHY_POWER_MGMT, phy_data); 2313 if (ret_val) 2314 return ret_val; 2315 } 2316 2317 /* LPLU and SmartSpeed are mutually exclusive. LPLU is used during 2318 * Dx states where the power conservation is most important. During 2319 * driver activity we should enable SmartSpeed, so performance is 2320 * maintained. */ 2321 if (hw->smart_speed == e1000_smart_speed_on) { 2322 ret_val = e1000_read_phy_reg(hw, 2323 IGP01E1000_PHY_PORT_CONFIG, &phy_data); 2324 if (ret_val) 2325 return ret_val; 2326 2327 phy_data |= IGP01E1000_PSCFR_SMART_SPEED; 2328 ret_val = e1000_write_phy_reg(hw, 2329 IGP01E1000_PHY_PORT_CONFIG, phy_data); 2330 if (ret_val) 2331 return ret_val; 2332 } else if (hw->smart_speed == e1000_smart_speed_off) { 2333 ret_val = e1000_read_phy_reg(hw, 2334 IGP01E1000_PHY_PORT_CONFIG, &phy_data); 2335 if (ret_val) 2336 return ret_val; 2337 2338 phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED; 2339 ret_val = e1000_write_phy_reg(hw, 2340 IGP01E1000_PHY_PORT_CONFIG, phy_data); 2341 if (ret_val) 2342 return ret_val; 2343 } 2344 2345 2346 } else { 2347 2348 if (hw->mac_type == e1000_ich8lan) { 2349 phy_ctrl |= E1000_PHY_CTRL_D0A_LPLU; 2350 E1000_WRITE_REG(hw, PHY_CTRL, phy_ctrl); 2351 } else { 2352 phy_data |= IGP02E1000_PM_D0_LPLU; 2353 ret_val = e1000_write_phy_reg(hw, 2354 IGP02E1000_PHY_POWER_MGMT, phy_data); 2355 if (ret_val) 2356 return ret_val; 2357 } 2358 2359 /* When LPLU is enabled we should disable SmartSpeed */ 2360 ret_val = e1000_read_phy_reg(hw, 2361 IGP01E1000_PHY_PORT_CONFIG, &phy_data); 2362 if (ret_val) 2363 return ret_val; 2364 2365 phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED; 2366 ret_val = e1000_write_phy_reg(hw, 2367 IGP01E1000_PHY_PORT_CONFIG, phy_data); 2368 if (ret_val) 2369 return ret_val; 2370 2371 } 2372 return E1000_SUCCESS; 2373 } 2374 2375 /******************************************************************** 2376 * Copper link setup for e1000_phy_igp series. 2377 * 2378 * hw - Struct containing variables accessed by shared code 2379 *********************************************************************/ 2380 static int32_t 2381 e1000_copper_link_igp_setup(struct e1000_hw *hw) 2382 { 2383 uint32_t led_ctrl; 2384 int32_t ret_val; 2385 uint16_t phy_data; 2386 2387 DEBUGFUNC(); 2388 2389 if (hw->phy_reset_disable) 2390 return E1000_SUCCESS; 2391 2392 ret_val = e1000_phy_reset(hw); 2393 if (ret_val) { 2394 DEBUGOUT("Error Resetting the PHY\n"); 2395 return ret_val; 2396 } 2397 2398 /* Wait 15ms for MAC to configure PHY from eeprom settings */ 2399 mdelay(15); 2400 if (hw->mac_type != e1000_ich8lan) { 2401 /* Configure activity LED after PHY reset */ 2402 led_ctrl = E1000_READ_REG(hw, LEDCTL); 2403 led_ctrl &= IGP_ACTIVITY_LED_MASK; 2404 led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE); 2405 E1000_WRITE_REG(hw, LEDCTL, led_ctrl); 2406 } 2407 2408 /* The NVM settings will configure LPLU in D3 for IGP2 and IGP3 PHYs */ 2409 if (hw->phy_type == e1000_phy_igp) { 2410 /* disable lplu d3 during driver init */ 2411 ret_val = e1000_set_d3_lplu_state(hw, FALSE); 2412 if (ret_val) { 2413 DEBUGOUT("Error Disabling LPLU D3\n"); 2414 return ret_val; 2415 } 2416 } 2417 2418 /* disable lplu d0 during driver init */ 2419 ret_val = e1000_set_d0_lplu_state(hw, FALSE); 2420 if (ret_val) { 2421 DEBUGOUT("Error Disabling LPLU D0\n"); 2422 return ret_val; 2423 } 2424 /* Configure mdi-mdix settings */ 2425 ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, &phy_data); 2426 if (ret_val) 2427 return ret_val; 2428 2429 if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) { 2430 hw->dsp_config_state = e1000_dsp_config_disabled; 2431 /* Force MDI for earlier revs of the IGP PHY */ 2432 phy_data &= ~(IGP01E1000_PSCR_AUTO_MDIX 2433 | IGP01E1000_PSCR_FORCE_MDI_MDIX); 2434 hw->mdix = 1; 2435 2436 } else { 2437 hw->dsp_config_state = e1000_dsp_config_enabled; 2438 phy_data &= ~IGP01E1000_PSCR_AUTO_MDIX; 2439 2440 switch (hw->mdix) { 2441 case 1: 2442 phy_data &= ~IGP01E1000_PSCR_FORCE_MDI_MDIX; 2443 break; 2444 case 2: 2445 phy_data |= IGP01E1000_PSCR_FORCE_MDI_MDIX; 2446 break; 2447 case 0: 2448 default: 2449 phy_data |= IGP01E1000_PSCR_AUTO_MDIX; 2450 break; 2451 } 2452 } 2453 ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, phy_data); 2454 if (ret_val) 2455 return ret_val; 2456 2457 /* set auto-master slave resolution settings */ 2458 if (hw->autoneg) { 2459 e1000_ms_type phy_ms_setting = hw->master_slave; 2460 2461 if (hw->ffe_config_state == e1000_ffe_config_active) 2462 hw->ffe_config_state = e1000_ffe_config_enabled; 2463 2464 if (hw->dsp_config_state == e1000_dsp_config_activated) 2465 hw->dsp_config_state = e1000_dsp_config_enabled; 2466 2467 /* when autonegotiation advertisment is only 1000Mbps then we 2468 * should disable SmartSpeed and enable Auto MasterSlave 2469 * resolution as hardware default. */ 2470 if (hw->autoneg_advertised == ADVERTISE_1000_FULL) { 2471 /* Disable SmartSpeed */ 2472 ret_val = e1000_read_phy_reg(hw, 2473 IGP01E1000_PHY_PORT_CONFIG, &phy_data); 2474 if (ret_val) 2475 return ret_val; 2476 phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED; 2477 ret_val = e1000_write_phy_reg(hw, 2478 IGP01E1000_PHY_PORT_CONFIG, phy_data); 2479 if (ret_val) 2480 return ret_val; 2481 /* Set auto Master/Slave resolution process */ 2482 ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, 2483 &phy_data); 2484 if (ret_val) 2485 return ret_val; 2486 phy_data &= ~CR_1000T_MS_ENABLE; 2487 ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, 2488 phy_data); 2489 if (ret_val) 2490 return ret_val; 2491 } 2492 2493 ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &phy_data); 2494 if (ret_val) 2495 return ret_val; 2496 2497 /* load defaults for future use */ 2498 hw->original_master_slave = (phy_data & CR_1000T_MS_ENABLE) ? 2499 ((phy_data & CR_1000T_MS_VALUE) ? 2500 e1000_ms_force_master : 2501 e1000_ms_force_slave) : 2502 e1000_ms_auto; 2503 2504 switch (phy_ms_setting) { 2505 case e1000_ms_force_master: 2506 phy_data |= (CR_1000T_MS_ENABLE | CR_1000T_MS_VALUE); 2507 break; 2508 case e1000_ms_force_slave: 2509 phy_data |= CR_1000T_MS_ENABLE; 2510 phy_data &= ~(CR_1000T_MS_VALUE); 2511 break; 2512 case e1000_ms_auto: 2513 phy_data &= ~CR_1000T_MS_ENABLE; 2514 default: 2515 break; 2516 } 2517 ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, phy_data); 2518 if (ret_val) 2519 return ret_val; 2520 } 2521 2522 return E1000_SUCCESS; 2523 } 2524 2525 /***************************************************************************** 2526 * This function checks the mode of the firmware. 2527 * 2528 * returns - TRUE when the mode is IAMT or FALSE. 2529 ****************************************************************************/ 2530 boolean_t 2531 e1000_check_mng_mode(struct e1000_hw *hw) 2532 { 2533 uint32_t fwsm; 2534 DEBUGFUNC(); 2535 2536 fwsm = E1000_READ_REG(hw, FWSM); 2537 2538 if (hw->mac_type == e1000_ich8lan) { 2539 if ((fwsm & E1000_FWSM_MODE_MASK) == 2540 (E1000_MNG_ICH_IAMT_MODE << E1000_FWSM_MODE_SHIFT)) 2541 return TRUE; 2542 } else if ((fwsm & E1000_FWSM_MODE_MASK) == 2543 (E1000_MNG_IAMT_MODE << E1000_FWSM_MODE_SHIFT)) 2544 return TRUE; 2545 2546 return FALSE; 2547 } 2548 2549 static int32_t 2550 e1000_write_kmrn_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t data) 2551 { 2552 uint16_t swfw = E1000_SWFW_PHY0_SM; 2553 uint32_t reg_val; 2554 DEBUGFUNC(); 2555 2556 if (e1000_is_second_port(hw)) 2557 swfw = E1000_SWFW_PHY1_SM; 2558 2559 if (e1000_swfw_sync_acquire(hw, swfw)) 2560 return -E1000_ERR_SWFW_SYNC; 2561 2562 reg_val = ((reg_addr << E1000_KUMCTRLSTA_OFFSET_SHIFT) 2563 & E1000_KUMCTRLSTA_OFFSET) | data; 2564 E1000_WRITE_REG(hw, KUMCTRLSTA, reg_val); 2565 udelay(2); 2566 2567 return E1000_SUCCESS; 2568 } 2569 2570 static int32_t 2571 e1000_read_kmrn_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t *data) 2572 { 2573 uint16_t swfw = E1000_SWFW_PHY0_SM; 2574 uint32_t reg_val; 2575 DEBUGFUNC(); 2576 2577 if (e1000_is_second_port(hw)) 2578 swfw = E1000_SWFW_PHY1_SM; 2579 2580 if (e1000_swfw_sync_acquire(hw, swfw)) 2581 return -E1000_ERR_SWFW_SYNC; 2582 2583 /* Write register address */ 2584 reg_val = ((reg_addr << E1000_KUMCTRLSTA_OFFSET_SHIFT) & 2585 E1000_KUMCTRLSTA_OFFSET) | E1000_KUMCTRLSTA_REN; 2586 E1000_WRITE_REG(hw, KUMCTRLSTA, reg_val); 2587 udelay(2); 2588 2589 /* Read the data returned */ 2590 reg_val = E1000_READ_REG(hw, KUMCTRLSTA); 2591 *data = (uint16_t)reg_val; 2592 2593 return E1000_SUCCESS; 2594 } 2595 2596 /******************************************************************** 2597 * Copper link setup for e1000_phy_gg82563 series. 2598 * 2599 * hw - Struct containing variables accessed by shared code 2600 *********************************************************************/ 2601 static int32_t 2602 e1000_copper_link_ggp_setup(struct e1000_hw *hw) 2603 { 2604 int32_t ret_val; 2605 uint16_t phy_data; 2606 uint32_t reg_data; 2607 2608 DEBUGFUNC(); 2609 2610 if (!hw->phy_reset_disable) { 2611 /* Enable CRS on TX for half-duplex operation. */ 2612 ret_val = e1000_read_phy_reg(hw, 2613 GG82563_PHY_MAC_SPEC_CTRL, &phy_data); 2614 if (ret_val) 2615 return ret_val; 2616 2617 phy_data |= GG82563_MSCR_ASSERT_CRS_ON_TX; 2618 /* Use 25MHz for both link down and 1000BASE-T for Tx clock */ 2619 phy_data |= GG82563_MSCR_TX_CLK_1000MBPS_25MHZ; 2620 2621 ret_val = e1000_write_phy_reg(hw, 2622 GG82563_PHY_MAC_SPEC_CTRL, phy_data); 2623 if (ret_val) 2624 return ret_val; 2625 2626 /* Options: 2627 * MDI/MDI-X = 0 (default) 2628 * 0 - Auto for all speeds 2629 * 1 - MDI mode 2630 * 2 - MDI-X mode 2631 * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes) 2632 */ 2633 ret_val = e1000_read_phy_reg(hw, 2634 GG82563_PHY_SPEC_CTRL, &phy_data); 2635 if (ret_val) 2636 return ret_val; 2637 2638 phy_data &= ~GG82563_PSCR_CROSSOVER_MODE_MASK; 2639 2640 switch (hw->mdix) { 2641 case 1: 2642 phy_data |= GG82563_PSCR_CROSSOVER_MODE_MDI; 2643 break; 2644 case 2: 2645 phy_data |= GG82563_PSCR_CROSSOVER_MODE_MDIX; 2646 break; 2647 case 0: 2648 default: 2649 phy_data |= GG82563_PSCR_CROSSOVER_MODE_AUTO; 2650 break; 2651 } 2652 2653 /* Options: 2654 * disable_polarity_correction = 0 (default) 2655 * Automatic Correction for Reversed Cable Polarity 2656 * 0 - Disabled 2657 * 1 - Enabled 2658 */ 2659 phy_data &= ~GG82563_PSCR_POLARITY_REVERSAL_DISABLE; 2660 ret_val = e1000_write_phy_reg(hw, 2661 GG82563_PHY_SPEC_CTRL, phy_data); 2662 2663 if (ret_val) 2664 return ret_val; 2665 2666 /* SW Reset the PHY so all changes take effect */ 2667 ret_val = e1000_phy_reset(hw); 2668 if (ret_val) { 2669 DEBUGOUT("Error Resetting the PHY\n"); 2670 return ret_val; 2671 } 2672 } /* phy_reset_disable */ 2673 2674 if (hw->mac_type == e1000_80003es2lan) { 2675 /* Bypass RX and TX FIFO's */ 2676 ret_val = e1000_write_kmrn_reg(hw, 2677 E1000_KUMCTRLSTA_OFFSET_FIFO_CTRL, 2678 E1000_KUMCTRLSTA_FIFO_CTRL_RX_BYPASS 2679 | E1000_KUMCTRLSTA_FIFO_CTRL_TX_BYPASS); 2680 if (ret_val) 2681 return ret_val; 2682 2683 ret_val = e1000_read_phy_reg(hw, 2684 GG82563_PHY_SPEC_CTRL_2, &phy_data); 2685 if (ret_val) 2686 return ret_val; 2687 2688 phy_data &= ~GG82563_PSCR2_REVERSE_AUTO_NEG; 2689 ret_val = e1000_write_phy_reg(hw, 2690 GG82563_PHY_SPEC_CTRL_2, phy_data); 2691 2692 if (ret_val) 2693 return ret_val; 2694 2695 reg_data = E1000_READ_REG(hw, CTRL_EXT); 2696 reg_data &= ~(E1000_CTRL_EXT_LINK_MODE_MASK); 2697 E1000_WRITE_REG(hw, CTRL_EXT, reg_data); 2698 2699 ret_val = e1000_read_phy_reg(hw, 2700 GG82563_PHY_PWR_MGMT_CTRL, &phy_data); 2701 if (ret_val) 2702 return ret_val; 2703 2704 /* Do not init these registers when the HW is in IAMT mode, since the 2705 * firmware will have already initialized them. We only initialize 2706 * them if the HW is not in IAMT mode. 2707 */ 2708 if (e1000_check_mng_mode(hw) == FALSE) { 2709 /* Enable Electrical Idle on the PHY */ 2710 phy_data |= GG82563_PMCR_ENABLE_ELECTRICAL_IDLE; 2711 ret_val = e1000_write_phy_reg(hw, 2712 GG82563_PHY_PWR_MGMT_CTRL, phy_data); 2713 if (ret_val) 2714 return ret_val; 2715 2716 ret_val = e1000_read_phy_reg(hw, 2717 GG82563_PHY_KMRN_MODE_CTRL, &phy_data); 2718 if (ret_val) 2719 return ret_val; 2720 2721 phy_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER; 2722 ret_val = e1000_write_phy_reg(hw, 2723 GG82563_PHY_KMRN_MODE_CTRL, phy_data); 2724 2725 if (ret_val) 2726 return ret_val; 2727 } 2728 2729 /* Workaround: Disable padding in Kumeran interface in the MAC 2730 * and in the PHY to avoid CRC errors. 2731 */ 2732 ret_val = e1000_read_phy_reg(hw, 2733 GG82563_PHY_INBAND_CTRL, &phy_data); 2734 if (ret_val) 2735 return ret_val; 2736 phy_data |= GG82563_ICR_DIS_PADDING; 2737 ret_val = e1000_write_phy_reg(hw, 2738 GG82563_PHY_INBAND_CTRL, phy_data); 2739 if (ret_val) 2740 return ret_val; 2741 } 2742 return E1000_SUCCESS; 2743 } 2744 2745 /******************************************************************** 2746 * Copper link setup for e1000_phy_m88 series. 2747 * 2748 * hw - Struct containing variables accessed by shared code 2749 *********************************************************************/ 2750 static int32_t 2751 e1000_copper_link_mgp_setup(struct e1000_hw *hw) 2752 { 2753 int32_t ret_val; 2754 uint16_t phy_data; 2755 2756 DEBUGFUNC(); 2757 2758 if (hw->phy_reset_disable) 2759 return E1000_SUCCESS; 2760 2761 /* Enable CRS on TX. This must be set for half-duplex operation. */ 2762 ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); 2763 if (ret_val) 2764 return ret_val; 2765 2766 phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX; 2767 2768 /* Options: 2769 * MDI/MDI-X = 0 (default) 2770 * 0 - Auto for all speeds 2771 * 1 - MDI mode 2772 * 2 - MDI-X mode 2773 * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes) 2774 */ 2775 phy_data &= ~M88E1000_PSCR_AUTO_X_MODE; 2776 2777 switch (hw->mdix) { 2778 case 1: 2779 phy_data |= M88E1000_PSCR_MDI_MANUAL_MODE; 2780 break; 2781 case 2: 2782 phy_data |= M88E1000_PSCR_MDIX_MANUAL_MODE; 2783 break; 2784 case 3: 2785 phy_data |= M88E1000_PSCR_AUTO_X_1000T; 2786 break; 2787 case 0: 2788 default: 2789 phy_data |= M88E1000_PSCR_AUTO_X_MODE; 2790 break; 2791 } 2792 2793 /* Options: 2794 * disable_polarity_correction = 0 (default) 2795 * Automatic Correction for Reversed Cable Polarity 2796 * 0 - Disabled 2797 * 1 - Enabled 2798 */ 2799 phy_data &= ~M88E1000_PSCR_POLARITY_REVERSAL; 2800 ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data); 2801 if (ret_val) 2802 return ret_val; 2803 2804 if (hw->phy_revision < M88E1011_I_REV_4) { 2805 /* Force TX_CLK in the Extended PHY Specific Control Register 2806 * to 25MHz clock. 2807 */ 2808 ret_val = e1000_read_phy_reg(hw, 2809 M88E1000_EXT_PHY_SPEC_CTRL, &phy_data); 2810 if (ret_val) 2811 return ret_val; 2812 2813 phy_data |= M88E1000_EPSCR_TX_CLK_25; 2814 2815 if ((hw->phy_revision == E1000_REVISION_2) && 2816 (hw->phy_id == M88E1111_I_PHY_ID)) { 2817 /* Vidalia Phy, set the downshift counter to 5x */ 2818 phy_data &= ~(M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK); 2819 phy_data |= M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X; 2820 ret_val = e1000_write_phy_reg(hw, 2821 M88E1000_EXT_PHY_SPEC_CTRL, phy_data); 2822 if (ret_val) 2823 return ret_val; 2824 } else { 2825 /* Configure Master and Slave downshift values */ 2826 phy_data &= ~(M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK 2827 | M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK); 2828 phy_data |= (M88E1000_EPSCR_MASTER_DOWNSHIFT_1X 2829 | M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X); 2830 ret_val = e1000_write_phy_reg(hw, 2831 M88E1000_EXT_PHY_SPEC_CTRL, phy_data); 2832 if (ret_val) 2833 return ret_val; 2834 } 2835 } 2836 2837 /* SW Reset the PHY so all changes take effect */ 2838 ret_val = e1000_phy_reset(hw); 2839 if (ret_val) { 2840 DEBUGOUT("Error Resetting the PHY\n"); 2841 return ret_val; 2842 } 2843 2844 return E1000_SUCCESS; 2845 } 2846 2847 /******************************************************************** 2848 * Setup auto-negotiation and flow control advertisements, 2849 * and then perform auto-negotiation. 2850 * 2851 * hw - Struct containing variables accessed by shared code 2852 *********************************************************************/ 2853 static int32_t 2854 e1000_copper_link_autoneg(struct e1000_hw *hw) 2855 { 2856 int32_t ret_val; 2857 uint16_t phy_data; 2858 2859 DEBUGFUNC(); 2860 2861 /* Perform some bounds checking on the hw->autoneg_advertised 2862 * parameter. If this variable is zero, then set it to the default. 2863 */ 2864 hw->autoneg_advertised &= AUTONEG_ADVERTISE_SPEED_DEFAULT; 2865 2866 /* If autoneg_advertised is zero, we assume it was not defaulted 2867 * by the calling code so we set to advertise full capability. 2868 */ 2869 if (hw->autoneg_advertised == 0) 2870 hw->autoneg_advertised = AUTONEG_ADVERTISE_SPEED_DEFAULT; 2871 2872 /* IFE phy only supports 10/100 */ 2873 if (hw->phy_type == e1000_phy_ife) 2874 hw->autoneg_advertised &= AUTONEG_ADVERTISE_10_100_ALL; 2875 2876 DEBUGOUT("Reconfiguring auto-neg advertisement params\n"); 2877 ret_val = e1000_phy_setup_autoneg(hw); 2878 if (ret_val) { 2879 DEBUGOUT("Error Setting up Auto-Negotiation\n"); 2880 return ret_val; 2881 } 2882 DEBUGOUT("Restarting Auto-Neg\n"); 2883 2884 /* Restart auto-negotiation by setting the Auto Neg Enable bit and 2885 * the Auto Neg Restart bit in the PHY control register. 2886 */ 2887 ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data); 2888 if (ret_val) 2889 return ret_val; 2890 2891 phy_data |= (MII_CR_AUTO_NEG_EN | MII_CR_RESTART_AUTO_NEG); 2892 ret_val = e1000_write_phy_reg(hw, PHY_CTRL, phy_data); 2893 if (ret_val) 2894 return ret_val; 2895 2896 /* Does the user want to wait for Auto-Neg to complete here, or 2897 * check at a later time (for example, callback routine). 2898 */ 2899 /* If we do not wait for autonegtation to complete I 2900 * do not see a valid link status. 2901 * wait_autoneg_complete = 1 . 2902 */ 2903 if (hw->wait_autoneg_complete) { 2904 ret_val = e1000_wait_autoneg(hw); 2905 if (ret_val) { 2906 DEBUGOUT("Error while waiting for autoneg" 2907 "to complete\n"); 2908 return ret_val; 2909 } 2910 } 2911 2912 hw->get_link_status = TRUE; 2913 2914 return E1000_SUCCESS; 2915 } 2916 2917 /****************************************************************************** 2918 * Config the MAC and the PHY after link is up. 2919 * 1) Set up the MAC to the current PHY speed/duplex 2920 * if we are on 82543. If we 2921 * are on newer silicon, we only need to configure 2922 * collision distance in the Transmit Control Register. 2923 * 2) Set up flow control on the MAC to that established with 2924 * the link partner. 2925 * 3) Config DSP to improve Gigabit link quality for some PHY revisions. 2926 * 2927 * hw - Struct containing variables accessed by shared code 2928 ******************************************************************************/ 2929 static int32_t 2930 e1000_copper_link_postconfig(struct e1000_hw *hw) 2931 { 2932 int32_t ret_val; 2933 DEBUGFUNC(); 2934 2935 if (hw->mac_type >= e1000_82544) { 2936 e1000_config_collision_dist(hw); 2937 } else { 2938 ret_val = e1000_config_mac_to_phy(hw); 2939 if (ret_val) { 2940 DEBUGOUT("Error configuring MAC to PHY settings\n"); 2941 return ret_val; 2942 } 2943 } 2944 ret_val = e1000_config_fc_after_link_up(hw); 2945 if (ret_val) { 2946 DEBUGOUT("Error Configuring Flow Control\n"); 2947 return ret_val; 2948 } 2949 return E1000_SUCCESS; 2950 } 2951 2952 /****************************************************************************** 2953 * Detects which PHY is present and setup the speed and duplex 2954 * 2955 * hw - Struct containing variables accessed by shared code 2956 ******************************************************************************/ 2957 static int 2958 e1000_setup_copper_link(struct eth_device *nic) 2959 { 2960 struct e1000_hw *hw = nic->priv; 2961 int32_t ret_val; 2962 uint16_t i; 2963 uint16_t phy_data; 2964 uint16_t reg_data; 2965 2966 DEBUGFUNC(); 2967 2968 switch (hw->mac_type) { 2969 case e1000_80003es2lan: 2970 case e1000_ich8lan: 2971 /* Set the mac to wait the maximum time between each 2972 * iteration and increase the max iterations when 2973 * polling the phy; this fixes erroneous timeouts at 10Mbps. */ 2974 ret_val = e1000_write_kmrn_reg(hw, 2975 GG82563_REG(0x34, 4), 0xFFFF); 2976 if (ret_val) 2977 return ret_val; 2978 ret_val = e1000_read_kmrn_reg(hw, 2979 GG82563_REG(0x34, 9), ®_data); 2980 if (ret_val) 2981 return ret_val; 2982 reg_data |= 0x3F; 2983 ret_val = e1000_write_kmrn_reg(hw, 2984 GG82563_REG(0x34, 9), reg_data); 2985 if (ret_val) 2986 return ret_val; 2987 default: 2988 break; 2989 } 2990 2991 /* Check if it is a valid PHY and set PHY mode if necessary. */ 2992 ret_val = e1000_copper_link_preconfig(hw); 2993 if (ret_val) 2994 return ret_val; 2995 switch (hw->mac_type) { 2996 case e1000_80003es2lan: 2997 /* Kumeran registers are written-only */ 2998 reg_data = 2999 E1000_KUMCTRLSTA_INB_CTRL_LINK_STATUS_TX_TIMEOUT_DEFAULT; 3000 reg_data |= E1000_KUMCTRLSTA_INB_CTRL_DIS_PADDING; 3001 ret_val = e1000_write_kmrn_reg(hw, 3002 E1000_KUMCTRLSTA_OFFSET_INB_CTRL, reg_data); 3003 if (ret_val) 3004 return ret_val; 3005 break; 3006 default: 3007 break; 3008 } 3009 3010 if (hw->phy_type == e1000_phy_igp || 3011 hw->phy_type == e1000_phy_igp_3 || 3012 hw->phy_type == e1000_phy_igp_2) { 3013 ret_val = e1000_copper_link_igp_setup(hw); 3014 if (ret_val) 3015 return ret_val; 3016 } else if (hw->phy_type == e1000_phy_m88) { 3017 ret_val = e1000_copper_link_mgp_setup(hw); 3018 if (ret_val) 3019 return ret_val; 3020 } else if (hw->phy_type == e1000_phy_gg82563) { 3021 ret_val = e1000_copper_link_ggp_setup(hw); 3022 if (ret_val) 3023 return ret_val; 3024 } 3025 3026 /* always auto */ 3027 /* Setup autoneg and flow control advertisement 3028 * and perform autonegotiation */ 3029 ret_val = e1000_copper_link_autoneg(hw); 3030 if (ret_val) 3031 return ret_val; 3032 3033 /* Check link status. Wait up to 100 microseconds for link to become 3034 * valid. 3035 */ 3036 for (i = 0; i < 10; i++) { 3037 ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data); 3038 if (ret_val) 3039 return ret_val; 3040 ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data); 3041 if (ret_val) 3042 return ret_val; 3043 3044 if (phy_data & MII_SR_LINK_STATUS) { 3045 /* Config the MAC and PHY after link is up */ 3046 ret_val = e1000_copper_link_postconfig(hw); 3047 if (ret_val) 3048 return ret_val; 3049 3050 DEBUGOUT("Valid link established!!!\n"); 3051 return E1000_SUCCESS; 3052 } 3053 udelay(10); 3054 } 3055 3056 DEBUGOUT("Unable to establish link!!!\n"); 3057 return E1000_SUCCESS; 3058 } 3059 3060 /****************************************************************************** 3061 * Configures PHY autoneg and flow control advertisement settings 3062 * 3063 * hw - Struct containing variables accessed by shared code 3064 ******************************************************************************/ 3065 int32_t 3066 e1000_phy_setup_autoneg(struct e1000_hw *hw) 3067 { 3068 int32_t ret_val; 3069 uint16_t mii_autoneg_adv_reg; 3070 uint16_t mii_1000t_ctrl_reg; 3071 3072 DEBUGFUNC(); 3073 3074 /* Read the MII Auto-Neg Advertisement Register (Address 4). */ 3075 ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_ADV, &mii_autoneg_adv_reg); 3076 if (ret_val) 3077 return ret_val; 3078 3079 if (hw->phy_type != e1000_phy_ife) { 3080 /* Read the MII 1000Base-T Control Register (Address 9). */ 3081 ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, 3082 &mii_1000t_ctrl_reg); 3083 if (ret_val) 3084 return ret_val; 3085 } else 3086 mii_1000t_ctrl_reg = 0; 3087 3088 /* Need to parse both autoneg_advertised and fc and set up 3089 * the appropriate PHY registers. First we will parse for 3090 * autoneg_advertised software override. Since we can advertise 3091 * a plethora of combinations, we need to check each bit 3092 * individually. 3093 */ 3094 3095 /* First we clear all the 10/100 mb speed bits in the Auto-Neg 3096 * Advertisement Register (Address 4) and the 1000 mb speed bits in 3097 * the 1000Base-T Control Register (Address 9). 3098 */ 3099 mii_autoneg_adv_reg &= ~REG4_SPEED_MASK; 3100 mii_1000t_ctrl_reg &= ~REG9_SPEED_MASK; 3101 3102 DEBUGOUT("autoneg_advertised %x\n", hw->autoneg_advertised); 3103 3104 /* Do we want to advertise 10 Mb Half Duplex? */ 3105 if (hw->autoneg_advertised & ADVERTISE_10_HALF) { 3106 DEBUGOUT("Advertise 10mb Half duplex\n"); 3107 mii_autoneg_adv_reg |= NWAY_AR_10T_HD_CAPS; 3108 } 3109 3110 /* Do we want to advertise 10 Mb Full Duplex? */ 3111 if (hw->autoneg_advertised & ADVERTISE_10_FULL) { 3112 DEBUGOUT("Advertise 10mb Full duplex\n"); 3113 mii_autoneg_adv_reg |= NWAY_AR_10T_FD_CAPS; 3114 } 3115 3116 /* Do we want to advertise 100 Mb Half Duplex? */ 3117 if (hw->autoneg_advertised & ADVERTISE_100_HALF) { 3118 DEBUGOUT("Advertise 100mb Half duplex\n"); 3119 mii_autoneg_adv_reg |= NWAY_AR_100TX_HD_CAPS; 3120 } 3121 3122 /* Do we want to advertise 100 Mb Full Duplex? */ 3123 if (hw->autoneg_advertised & ADVERTISE_100_FULL) { 3124 DEBUGOUT("Advertise 100mb Full duplex\n"); 3125 mii_autoneg_adv_reg |= NWAY_AR_100TX_FD_CAPS; 3126 } 3127 3128 /* We do not allow the Phy to advertise 1000 Mb Half Duplex */ 3129 if (hw->autoneg_advertised & ADVERTISE_1000_HALF) { 3130 DEBUGOUT 3131 ("Advertise 1000mb Half duplex requested, request denied!\n"); 3132 } 3133 3134 /* Do we want to advertise 1000 Mb Full Duplex? */ 3135 if (hw->autoneg_advertised & ADVERTISE_1000_FULL) { 3136 DEBUGOUT("Advertise 1000mb Full duplex\n"); 3137 mii_1000t_ctrl_reg |= CR_1000T_FD_CAPS; 3138 } 3139 3140 /* Check for a software override of the flow control settings, and 3141 * setup the PHY advertisement registers accordingly. If 3142 * auto-negotiation is enabled, then software will have to set the 3143 * "PAUSE" bits to the correct value in the Auto-Negotiation 3144 * Advertisement Register (PHY_AUTONEG_ADV) and re-start auto-negotiation. 3145 * 3146 * The possible values of the "fc" parameter are: 3147 * 0: Flow control is completely disabled 3148 * 1: Rx flow control is enabled (we can receive pause frames 3149 * but not send pause frames). 3150 * 2: Tx flow control is enabled (we can send pause frames 3151 * but we do not support receiving pause frames). 3152 * 3: Both Rx and TX flow control (symmetric) are enabled. 3153 * other: No software override. The flow control configuration 3154 * in the EEPROM is used. 3155 */ 3156 switch (hw->fc) { 3157 case e1000_fc_none: /* 0 */ 3158 /* Flow control (RX & TX) is completely disabled by a 3159 * software over-ride. 3160 */ 3161 mii_autoneg_adv_reg &= ~(NWAY_AR_ASM_DIR | NWAY_AR_PAUSE); 3162 break; 3163 case e1000_fc_rx_pause: /* 1 */ 3164 /* RX Flow control is enabled, and TX Flow control is 3165 * disabled, by a software over-ride. 3166 */ 3167 /* Since there really isn't a way to advertise that we are 3168 * capable of RX Pause ONLY, we will advertise that we 3169 * support both symmetric and asymmetric RX PAUSE. Later 3170 * (in e1000_config_fc_after_link_up) we will disable the 3171 *hw's ability to send PAUSE frames. 3172 */ 3173 mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE); 3174 break; 3175 case e1000_fc_tx_pause: /* 2 */ 3176 /* TX Flow control is enabled, and RX Flow control is 3177 * disabled, by a software over-ride. 3178 */ 3179 mii_autoneg_adv_reg |= NWAY_AR_ASM_DIR; 3180 mii_autoneg_adv_reg &= ~NWAY_AR_PAUSE; 3181 break; 3182 case e1000_fc_full: /* 3 */ 3183 /* Flow control (both RX and TX) is enabled by a software 3184 * over-ride. 3185 */ 3186 mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE); 3187 break; 3188 default: 3189 DEBUGOUT("Flow control param set incorrectly\n"); 3190 return -E1000_ERR_CONFIG; 3191 } 3192 3193 ret_val = e1000_write_phy_reg(hw, PHY_AUTONEG_ADV, mii_autoneg_adv_reg); 3194 if (ret_val) 3195 return ret_val; 3196 3197 DEBUGOUT("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg); 3198 3199 if (hw->phy_type != e1000_phy_ife) { 3200 ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, 3201 mii_1000t_ctrl_reg); 3202 if (ret_val) 3203 return ret_val; 3204 } 3205 3206 return E1000_SUCCESS; 3207 } 3208 3209 /****************************************************************************** 3210 * Sets the collision distance in the Transmit Control register 3211 * 3212 * hw - Struct containing variables accessed by shared code 3213 * 3214 * Link should have been established previously. Reads the speed and duplex 3215 * information from the Device Status register. 3216 ******************************************************************************/ 3217 static void 3218 e1000_config_collision_dist(struct e1000_hw *hw) 3219 { 3220 uint32_t tctl, coll_dist; 3221 3222 DEBUGFUNC(); 3223 3224 if (hw->mac_type < e1000_82543) 3225 coll_dist = E1000_COLLISION_DISTANCE_82542; 3226 else 3227 coll_dist = E1000_COLLISION_DISTANCE; 3228 3229 tctl = E1000_READ_REG(hw, TCTL); 3230 3231 tctl &= ~E1000_TCTL_COLD; 3232 tctl |= coll_dist << E1000_COLD_SHIFT; 3233 3234 E1000_WRITE_REG(hw, TCTL, tctl); 3235 E1000_WRITE_FLUSH(hw); 3236 } 3237 3238 /****************************************************************************** 3239 * Sets MAC speed and duplex settings to reflect the those in the PHY 3240 * 3241 * hw - Struct containing variables accessed by shared code 3242 * mii_reg - data to write to the MII control register 3243 * 3244 * The contents of the PHY register containing the needed information need to 3245 * be passed in. 3246 ******************************************************************************/ 3247 static int 3248 e1000_config_mac_to_phy(struct e1000_hw *hw) 3249 { 3250 uint32_t ctrl; 3251 uint16_t phy_data; 3252 3253 DEBUGFUNC(); 3254 3255 /* Read the Device Control Register and set the bits to Force Speed 3256 * and Duplex. 3257 */ 3258 ctrl = E1000_READ_REG(hw, CTRL); 3259 ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); 3260 ctrl &= ~(E1000_CTRL_SPD_SEL | E1000_CTRL_ILOS); 3261 3262 /* Set up duplex in the Device Control and Transmit Control 3263 * registers depending on negotiated values. 3264 */ 3265 if (e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data) < 0) { 3266 DEBUGOUT("PHY Read Error\n"); 3267 return -E1000_ERR_PHY; 3268 } 3269 if (phy_data & M88E1000_PSSR_DPLX) 3270 ctrl |= E1000_CTRL_FD; 3271 else 3272 ctrl &= ~E1000_CTRL_FD; 3273 3274 e1000_config_collision_dist(hw); 3275 3276 /* Set up speed in the Device Control register depending on 3277 * negotiated values. 3278 */ 3279 if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS) 3280 ctrl |= E1000_CTRL_SPD_1000; 3281 else if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_100MBS) 3282 ctrl |= E1000_CTRL_SPD_100; 3283 /* Write the configured values back to the Device Control Reg. */ 3284 E1000_WRITE_REG(hw, CTRL, ctrl); 3285 return 0; 3286 } 3287 3288 /****************************************************************************** 3289 * Forces the MAC's flow control settings. 3290 * 3291 * hw - Struct containing variables accessed by shared code 3292 * 3293 * Sets the TFCE and RFCE bits in the device control register to reflect 3294 * the adapter settings. TFCE and RFCE need to be explicitly set by 3295 * software when a Copper PHY is used because autonegotiation is managed 3296 * by the PHY rather than the MAC. Software must also configure these 3297 * bits when link is forced on a fiber connection. 3298 *****************************************************************************/ 3299 static int 3300 e1000_force_mac_fc(struct e1000_hw *hw) 3301 { 3302 uint32_t ctrl; 3303 3304 DEBUGFUNC(); 3305 3306 /* Get the current configuration of the Device Control Register */ 3307 ctrl = E1000_READ_REG(hw, CTRL); 3308 3309 /* Because we didn't get link via the internal auto-negotiation 3310 * mechanism (we either forced link or we got link via PHY 3311 * auto-neg), we have to manually enable/disable transmit an 3312 * receive flow control. 3313 * 3314 * The "Case" statement below enables/disable flow control 3315 * according to the "hw->fc" parameter. 3316 * 3317 * The possible values of the "fc" parameter are: 3318 * 0: Flow control is completely disabled 3319 * 1: Rx flow control is enabled (we can receive pause 3320 * frames but not send pause frames). 3321 * 2: Tx flow control is enabled (we can send pause frames 3322 * frames but we do not receive pause frames). 3323 * 3: Both Rx and TX flow control (symmetric) is enabled. 3324 * other: No other values should be possible at this point. 3325 */ 3326 3327 switch (hw->fc) { 3328 case e1000_fc_none: 3329 ctrl &= (~(E1000_CTRL_TFCE | E1000_CTRL_RFCE)); 3330 break; 3331 case e1000_fc_rx_pause: 3332 ctrl &= (~E1000_CTRL_TFCE); 3333 ctrl |= E1000_CTRL_RFCE; 3334 break; 3335 case e1000_fc_tx_pause: 3336 ctrl &= (~E1000_CTRL_RFCE); 3337 ctrl |= E1000_CTRL_TFCE; 3338 break; 3339 case e1000_fc_full: 3340 ctrl |= (E1000_CTRL_TFCE | E1000_CTRL_RFCE); 3341 break; 3342 default: 3343 DEBUGOUT("Flow control param set incorrectly\n"); 3344 return -E1000_ERR_CONFIG; 3345 } 3346 3347 /* Disable TX Flow Control for 82542 (rev 2.0) */ 3348 if (hw->mac_type == e1000_82542_rev2_0) 3349 ctrl &= (~E1000_CTRL_TFCE); 3350 3351 E1000_WRITE_REG(hw, CTRL, ctrl); 3352 return 0; 3353 } 3354 3355 /****************************************************************************** 3356 * Configures flow control settings after link is established 3357 * 3358 * hw - Struct containing variables accessed by shared code 3359 * 3360 * Should be called immediately after a valid link has been established. 3361 * Forces MAC flow control settings if link was forced. When in MII/GMII mode 3362 * and autonegotiation is enabled, the MAC flow control settings will be set 3363 * based on the flow control negotiated by the PHY. In TBI mode, the TFCE 3364 * and RFCE bits will be automaticaly set to the negotiated flow control mode. 3365 *****************************************************************************/ 3366 static int32_t 3367 e1000_config_fc_after_link_up(struct e1000_hw *hw) 3368 { 3369 int32_t ret_val; 3370 uint16_t mii_status_reg; 3371 uint16_t mii_nway_adv_reg; 3372 uint16_t mii_nway_lp_ability_reg; 3373 uint16_t speed; 3374 uint16_t duplex; 3375 3376 DEBUGFUNC(); 3377 3378 /* Check for the case where we have fiber media and auto-neg failed 3379 * so we had to force link. In this case, we need to force the 3380 * configuration of the MAC to match the "fc" parameter. 3381 */ 3382 if (((hw->media_type == e1000_media_type_fiber) && (hw->autoneg_failed)) 3383 || ((hw->media_type == e1000_media_type_internal_serdes) 3384 && (hw->autoneg_failed)) 3385 || ((hw->media_type == e1000_media_type_copper) 3386 && (!hw->autoneg))) { 3387 ret_val = e1000_force_mac_fc(hw); 3388 if (ret_val < 0) { 3389 DEBUGOUT("Error forcing flow control settings\n"); 3390 return ret_val; 3391 } 3392 } 3393 3394 /* Check for the case where we have copper media and auto-neg is 3395 * enabled. In this case, we need to check and see if Auto-Neg 3396 * has completed, and if so, how the PHY and link partner has 3397 * flow control configured. 3398 */ 3399 if (hw->media_type == e1000_media_type_copper) { 3400 /* Read the MII Status Register and check to see if AutoNeg 3401 * has completed. We read this twice because this reg has 3402 * some "sticky" (latched) bits. 3403 */ 3404 if (e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg) < 0) { 3405 DEBUGOUT("PHY Read Error \n"); 3406 return -E1000_ERR_PHY; 3407 } 3408 if (e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg) < 0) { 3409 DEBUGOUT("PHY Read Error \n"); 3410 return -E1000_ERR_PHY; 3411 } 3412 3413 if (mii_status_reg & MII_SR_AUTONEG_COMPLETE) { 3414 /* The AutoNeg process has completed, so we now need to 3415 * read both the Auto Negotiation Advertisement Register 3416 * (Address 4) and the Auto_Negotiation Base Page Ability 3417 * Register (Address 5) to determine how flow control was 3418 * negotiated. 3419 */ 3420 if (e1000_read_phy_reg 3421 (hw, PHY_AUTONEG_ADV, &mii_nway_adv_reg) < 0) { 3422 DEBUGOUT("PHY Read Error\n"); 3423 return -E1000_ERR_PHY; 3424 } 3425 if (e1000_read_phy_reg 3426 (hw, PHY_LP_ABILITY, 3427 &mii_nway_lp_ability_reg) < 0) { 3428 DEBUGOUT("PHY Read Error\n"); 3429 return -E1000_ERR_PHY; 3430 } 3431 3432 /* Two bits in the Auto Negotiation Advertisement Register 3433 * (Address 4) and two bits in the Auto Negotiation Base 3434 * Page Ability Register (Address 5) determine flow control 3435 * for both the PHY and the link partner. The following 3436 * table, taken out of the IEEE 802.3ab/D6.0 dated March 25, 3437 * 1999, describes these PAUSE resolution bits and how flow 3438 * control is determined based upon these settings. 3439 * NOTE: DC = Don't Care 3440 * 3441 * LOCAL DEVICE | LINK PARTNER 3442 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | NIC Resolution 3443 *-------|---------|-------|---------|-------------------- 3444 * 0 | 0 | DC | DC | e1000_fc_none 3445 * 0 | 1 | 0 | DC | e1000_fc_none 3446 * 0 | 1 | 1 | 0 | e1000_fc_none 3447 * 0 | 1 | 1 | 1 | e1000_fc_tx_pause 3448 * 1 | 0 | 0 | DC | e1000_fc_none 3449 * 1 | DC | 1 | DC | e1000_fc_full 3450 * 1 | 1 | 0 | 0 | e1000_fc_none 3451 * 1 | 1 | 0 | 1 | e1000_fc_rx_pause 3452 * 3453 */ 3454 /* Are both PAUSE bits set to 1? If so, this implies 3455 * Symmetric Flow Control is enabled at both ends. The 3456 * ASM_DIR bits are irrelevant per the spec. 3457 * 3458 * For Symmetric Flow Control: 3459 * 3460 * LOCAL DEVICE | LINK PARTNER 3461 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result 3462 *-------|---------|-------|---------|-------------------- 3463 * 1 | DC | 1 | DC | e1000_fc_full 3464 * 3465 */ 3466 if ((mii_nway_adv_reg & NWAY_AR_PAUSE) && 3467 (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE)) { 3468 /* Now we need to check if the user selected RX ONLY 3469 * of pause frames. In this case, we had to advertise 3470 * FULL flow control because we could not advertise RX 3471 * ONLY. Hence, we must now check to see if we need to 3472 * turn OFF the TRANSMISSION of PAUSE frames. 3473 */ 3474 if (hw->original_fc == e1000_fc_full) { 3475 hw->fc = e1000_fc_full; 3476 DEBUGOUT("Flow Control = FULL.\r\n"); 3477 } else { 3478 hw->fc = e1000_fc_rx_pause; 3479 DEBUGOUT 3480 ("Flow Control = RX PAUSE frames only.\r\n"); 3481 } 3482 } 3483 /* For receiving PAUSE frames ONLY. 3484 * 3485 * LOCAL DEVICE | LINK PARTNER 3486 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result 3487 *-------|---------|-------|---------|-------------------- 3488 * 0 | 1 | 1 | 1 | e1000_fc_tx_pause 3489 * 3490 */ 3491 else if (!(mii_nway_adv_reg & NWAY_AR_PAUSE) && 3492 (mii_nway_adv_reg & NWAY_AR_ASM_DIR) && 3493 (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) && 3494 (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) 3495 { 3496 hw->fc = e1000_fc_tx_pause; 3497 DEBUGOUT 3498 ("Flow Control = TX PAUSE frames only.\r\n"); 3499 } 3500 /* For transmitting PAUSE frames ONLY. 3501 * 3502 * LOCAL DEVICE | LINK PARTNER 3503 * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result 3504 *-------|---------|-------|---------|-------------------- 3505 * 1 | 1 | 0 | 1 | e1000_fc_rx_pause 3506 * 3507 */ 3508 else if ((mii_nway_adv_reg & NWAY_AR_PAUSE) && 3509 (mii_nway_adv_reg & NWAY_AR_ASM_DIR) && 3510 !(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) && 3511 (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) 3512 { 3513 hw->fc = e1000_fc_rx_pause; 3514 DEBUGOUT 3515 ("Flow Control = RX PAUSE frames only.\r\n"); 3516 } 3517 /* Per the IEEE spec, at this point flow control should be 3518 * disabled. However, we want to consider that we could 3519 * be connected to a legacy switch that doesn't advertise 3520 * desired flow control, but can be forced on the link 3521 * partner. So if we advertised no flow control, that is 3522 * what we will resolve to. If we advertised some kind of 3523 * receive capability (Rx Pause Only or Full Flow Control) 3524 * and the link partner advertised none, we will configure 3525 * ourselves to enable Rx Flow Control only. We can do 3526 * this safely for two reasons: If the link partner really 3527 * didn't want flow control enabled, and we enable Rx, no 3528 * harm done since we won't be receiving any PAUSE frames 3529 * anyway. If the intent on the link partner was to have 3530 * flow control enabled, then by us enabling RX only, we 3531 * can at least receive pause frames and process them. 3532 * This is a good idea because in most cases, since we are 3533 * predominantly a server NIC, more times than not we will 3534 * be asked to delay transmission of packets than asking 3535 * our link partner to pause transmission of frames. 3536 */ 3537 else if (hw->original_fc == e1000_fc_none || 3538 hw->original_fc == e1000_fc_tx_pause) { 3539 hw->fc = e1000_fc_none; 3540 DEBUGOUT("Flow Control = NONE.\r\n"); 3541 } else { 3542 hw->fc = e1000_fc_rx_pause; 3543 DEBUGOUT 3544 ("Flow Control = RX PAUSE frames only.\r\n"); 3545 } 3546 3547 /* Now we need to do one last check... If we auto- 3548 * negotiated to HALF DUPLEX, flow control should not be 3549 * enabled per IEEE 802.3 spec. 3550 */ 3551 e1000_get_speed_and_duplex(hw, &speed, &duplex); 3552 3553 if (duplex == HALF_DUPLEX) 3554 hw->fc = e1000_fc_none; 3555 3556 /* Now we call a subroutine to actually force the MAC 3557 * controller to use the correct flow control settings. 3558 */ 3559 ret_val = e1000_force_mac_fc(hw); 3560 if (ret_val < 0) { 3561 DEBUGOUT 3562 ("Error forcing flow control settings\n"); 3563 return ret_val; 3564 } 3565 } else { 3566 DEBUGOUT 3567 ("Copper PHY and Auto Neg has not completed.\r\n"); 3568 } 3569 } 3570 return E1000_SUCCESS; 3571 } 3572 3573 /****************************************************************************** 3574 * Checks to see if the link status of the hardware has changed. 3575 * 3576 * hw - Struct containing variables accessed by shared code 3577 * 3578 * Called by any function that needs to check the link status of the adapter. 3579 *****************************************************************************/ 3580 static int 3581 e1000_check_for_link(struct eth_device *nic) 3582 { 3583 struct e1000_hw *hw = nic->priv; 3584 uint32_t rxcw; 3585 uint32_t ctrl; 3586 uint32_t status; 3587 uint32_t rctl; 3588 uint32_t signal; 3589 int32_t ret_val; 3590 uint16_t phy_data; 3591 uint16_t lp_capability; 3592 3593 DEBUGFUNC(); 3594 3595 /* On adapters with a MAC newer that 82544, SW Defineable pin 1 will be 3596 * set when the optics detect a signal. On older adapters, it will be 3597 * cleared when there is a signal 3598 */ 3599 ctrl = E1000_READ_REG(hw, CTRL); 3600 if ((hw->mac_type > e1000_82544) && !(ctrl & E1000_CTRL_ILOS)) 3601 signal = E1000_CTRL_SWDPIN1; 3602 else 3603 signal = 0; 3604 3605 status = E1000_READ_REG(hw, STATUS); 3606 rxcw = E1000_READ_REG(hw, RXCW); 3607 DEBUGOUT("ctrl: %#08x status %#08x rxcw %#08x\n", ctrl, status, rxcw); 3608 3609 /* If we have a copper PHY then we only want to go out to the PHY 3610 * registers to see if Auto-Neg has completed and/or if our link 3611 * status has changed. The get_link_status flag will be set if we 3612 * receive a Link Status Change interrupt or we have Rx Sequence 3613 * Errors. 3614 */ 3615 if ((hw->media_type == e1000_media_type_copper) && hw->get_link_status) { 3616 /* First we want to see if the MII Status Register reports 3617 * link. If so, then we want to get the current speed/duplex 3618 * of the PHY. 3619 * Read the register twice since the link bit is sticky. 3620 */ 3621 if (e1000_read_phy_reg(hw, PHY_STATUS, &phy_data) < 0) { 3622 DEBUGOUT("PHY Read Error\n"); 3623 return -E1000_ERR_PHY; 3624 } 3625 if (e1000_read_phy_reg(hw, PHY_STATUS, &phy_data) < 0) { 3626 DEBUGOUT("PHY Read Error\n"); 3627 return -E1000_ERR_PHY; 3628 } 3629 3630 if (phy_data & MII_SR_LINK_STATUS) { 3631 hw->get_link_status = FALSE; 3632 } else { 3633 /* No link detected */ 3634 return -E1000_ERR_NOLINK; 3635 } 3636 3637 /* We have a M88E1000 PHY and Auto-Neg is enabled. If we 3638 * have Si on board that is 82544 or newer, Auto 3639 * Speed Detection takes care of MAC speed/duplex 3640 * configuration. So we only need to configure Collision 3641 * Distance in the MAC. Otherwise, we need to force 3642 * speed/duplex on the MAC to the current PHY speed/duplex 3643 * settings. 3644 */ 3645 if (hw->mac_type >= e1000_82544) 3646 e1000_config_collision_dist(hw); 3647 else { 3648 ret_val = e1000_config_mac_to_phy(hw); 3649 if (ret_val < 0) { 3650 DEBUGOUT 3651 ("Error configuring MAC to PHY settings\n"); 3652 return ret_val; 3653 } 3654 } 3655 3656 /* Configure Flow Control now that Auto-Neg has completed. First, we 3657 * need to restore the desired flow control settings because we may 3658 * have had to re-autoneg with a different link partner. 3659 */ 3660 ret_val = e1000_config_fc_after_link_up(hw); 3661 if (ret_val < 0) { 3662 DEBUGOUT("Error configuring flow control\n"); 3663 return ret_val; 3664 } 3665 3666 /* At this point we know that we are on copper and we have 3667 * auto-negotiated link. These are conditions for checking the link 3668 * parter capability register. We use the link partner capability to 3669 * determine if TBI Compatibility needs to be turned on or off. If 3670 * the link partner advertises any speed in addition to Gigabit, then 3671 * we assume that they are GMII-based, and TBI compatibility is not 3672 * needed. If no other speeds are advertised, we assume the link 3673 * partner is TBI-based, and we turn on TBI Compatibility. 3674 */ 3675 if (hw->tbi_compatibility_en) { 3676 if (e1000_read_phy_reg 3677 (hw, PHY_LP_ABILITY, &lp_capability) < 0) { 3678 DEBUGOUT("PHY Read Error\n"); 3679 return -E1000_ERR_PHY; 3680 } 3681 if (lp_capability & (NWAY_LPAR_10T_HD_CAPS | 3682 NWAY_LPAR_10T_FD_CAPS | 3683 NWAY_LPAR_100TX_HD_CAPS | 3684 NWAY_LPAR_100TX_FD_CAPS | 3685 NWAY_LPAR_100T4_CAPS)) { 3686 /* If our link partner advertises anything in addition to 3687 * gigabit, we do not need to enable TBI compatibility. 3688 */ 3689 if (hw->tbi_compatibility_on) { 3690 /* If we previously were in the mode, turn it off. */ 3691 rctl = E1000_READ_REG(hw, RCTL); 3692 rctl &= ~E1000_RCTL_SBP; 3693 E1000_WRITE_REG(hw, RCTL, rctl); 3694 hw->tbi_compatibility_on = FALSE; 3695 } 3696 } else { 3697 /* If TBI compatibility is was previously off, turn it on. For 3698 * compatibility with a TBI link partner, we will store bad 3699 * packets. Some frames have an additional byte on the end and 3700 * will look like CRC errors to to the hardware. 3701 */ 3702 if (!hw->tbi_compatibility_on) { 3703 hw->tbi_compatibility_on = TRUE; 3704 rctl = E1000_READ_REG(hw, RCTL); 3705 rctl |= E1000_RCTL_SBP; 3706 E1000_WRITE_REG(hw, RCTL, rctl); 3707 } 3708 } 3709 } 3710 } 3711 /* If we don't have link (auto-negotiation failed or link partner cannot 3712 * auto-negotiate), the cable is plugged in (we have signal), and our 3713 * link partner is not trying to auto-negotiate with us (we are receiving 3714 * idles or data), we need to force link up. We also need to give 3715 * auto-negotiation time to complete, in case the cable was just plugged 3716 * in. The autoneg_failed flag does this. 3717 */ 3718 else if ((hw->media_type == e1000_media_type_fiber) && 3719 (!(status & E1000_STATUS_LU)) && 3720 ((ctrl & E1000_CTRL_SWDPIN1) == signal) && 3721 (!(rxcw & E1000_RXCW_C))) { 3722 if (hw->autoneg_failed == 0) { 3723 hw->autoneg_failed = 1; 3724 return 0; 3725 } 3726 DEBUGOUT("NOT RXing /C/, disable AutoNeg and force link.\r\n"); 3727 3728 /* Disable auto-negotiation in the TXCW register */ 3729 E1000_WRITE_REG(hw, TXCW, (hw->txcw & ~E1000_TXCW_ANE)); 3730 3731 /* Force link-up and also force full-duplex. */ 3732 ctrl = E1000_READ_REG(hw, CTRL); 3733 ctrl |= (E1000_CTRL_SLU | E1000_CTRL_FD); 3734 E1000_WRITE_REG(hw, CTRL, ctrl); 3735 3736 /* Configure Flow Control after forcing link up. */ 3737 ret_val = e1000_config_fc_after_link_up(hw); 3738 if (ret_val < 0) { 3739 DEBUGOUT("Error configuring flow control\n"); 3740 return ret_val; 3741 } 3742 } 3743 /* If we are forcing link and we are receiving /C/ ordered sets, re-enable 3744 * auto-negotiation in the TXCW register and disable forced link in the 3745 * Device Control register in an attempt to auto-negotiate with our link 3746 * partner. 3747 */ 3748 else if ((hw->media_type == e1000_media_type_fiber) && 3749 (ctrl & E1000_CTRL_SLU) && (rxcw & E1000_RXCW_C)) { 3750 DEBUGOUT 3751 ("RXing /C/, enable AutoNeg and stop forcing link.\r\n"); 3752 E1000_WRITE_REG(hw, TXCW, hw->txcw); 3753 E1000_WRITE_REG(hw, CTRL, (ctrl & ~E1000_CTRL_SLU)); 3754 } 3755 return 0; 3756 } 3757 3758 /****************************************************************************** 3759 * Configure the MAC-to-PHY interface for 10/100Mbps 3760 * 3761 * hw - Struct containing variables accessed by shared code 3762 ******************************************************************************/ 3763 static int32_t 3764 e1000_configure_kmrn_for_10_100(struct e1000_hw *hw, uint16_t duplex) 3765 { 3766 int32_t ret_val = E1000_SUCCESS; 3767 uint32_t tipg; 3768 uint16_t reg_data; 3769 3770 DEBUGFUNC(); 3771 3772 reg_data = E1000_KUMCTRLSTA_HD_CTRL_10_100_DEFAULT; 3773 ret_val = e1000_write_kmrn_reg(hw, 3774 E1000_KUMCTRLSTA_OFFSET_HD_CTRL, reg_data); 3775 if (ret_val) 3776 return ret_val; 3777 3778 /* Configure Transmit Inter-Packet Gap */ 3779 tipg = E1000_READ_REG(hw, TIPG); 3780 tipg &= ~E1000_TIPG_IPGT_MASK; 3781 tipg |= DEFAULT_80003ES2LAN_TIPG_IPGT_10_100; 3782 E1000_WRITE_REG(hw, TIPG, tipg); 3783 3784 ret_val = e1000_read_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, ®_data); 3785 3786 if (ret_val) 3787 return ret_val; 3788 3789 if (duplex == HALF_DUPLEX) 3790 reg_data |= GG82563_KMCR_PASS_FALSE_CARRIER; 3791 else 3792 reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER; 3793 3794 ret_val = e1000_write_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data); 3795 3796 return ret_val; 3797 } 3798 3799 static int32_t 3800 e1000_configure_kmrn_for_1000(struct e1000_hw *hw) 3801 { 3802 int32_t ret_val = E1000_SUCCESS; 3803 uint16_t reg_data; 3804 uint32_t tipg; 3805 3806 DEBUGFUNC(); 3807 3808 reg_data = E1000_KUMCTRLSTA_HD_CTRL_1000_DEFAULT; 3809 ret_val = e1000_write_kmrn_reg(hw, 3810 E1000_KUMCTRLSTA_OFFSET_HD_CTRL, reg_data); 3811 if (ret_val) 3812 return ret_val; 3813 3814 /* Configure Transmit Inter-Packet Gap */ 3815 tipg = E1000_READ_REG(hw, TIPG); 3816 tipg &= ~E1000_TIPG_IPGT_MASK; 3817 tipg |= DEFAULT_80003ES2LAN_TIPG_IPGT_1000; 3818 E1000_WRITE_REG(hw, TIPG, tipg); 3819 3820 ret_val = e1000_read_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, ®_data); 3821 3822 if (ret_val) 3823 return ret_val; 3824 3825 reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER; 3826 ret_val = e1000_write_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data); 3827 3828 return ret_val; 3829 } 3830 3831 /****************************************************************************** 3832 * Detects the current speed and duplex settings of the hardware. 3833 * 3834 * hw - Struct containing variables accessed by shared code 3835 * speed - Speed of the connection 3836 * duplex - Duplex setting of the connection 3837 *****************************************************************************/ 3838 static int 3839 e1000_get_speed_and_duplex(struct e1000_hw *hw, uint16_t *speed, 3840 uint16_t *duplex) 3841 { 3842 uint32_t status; 3843 int32_t ret_val; 3844 uint16_t phy_data; 3845 3846 DEBUGFUNC(); 3847 3848 if (hw->mac_type >= e1000_82543) { 3849 status = E1000_READ_REG(hw, STATUS); 3850 if (status & E1000_STATUS_SPEED_1000) { 3851 *speed = SPEED_1000; 3852 DEBUGOUT("1000 Mbs, "); 3853 } else if (status & E1000_STATUS_SPEED_100) { 3854 *speed = SPEED_100; 3855 DEBUGOUT("100 Mbs, "); 3856 } else { 3857 *speed = SPEED_10; 3858 DEBUGOUT("10 Mbs, "); 3859 } 3860 3861 if (status & E1000_STATUS_FD) { 3862 *duplex = FULL_DUPLEX; 3863 DEBUGOUT("Full Duplex\r\n"); 3864 } else { 3865 *duplex = HALF_DUPLEX; 3866 DEBUGOUT(" Half Duplex\r\n"); 3867 } 3868 } else { 3869 DEBUGOUT("1000 Mbs, Full Duplex\r\n"); 3870 *speed = SPEED_1000; 3871 *duplex = FULL_DUPLEX; 3872 } 3873 3874 /* IGP01 PHY may advertise full duplex operation after speed downgrade 3875 * even if it is operating at half duplex. Here we set the duplex 3876 * settings to match the duplex in the link partner's capabilities. 3877 */ 3878 if (hw->phy_type == e1000_phy_igp && hw->speed_downgraded) { 3879 ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_EXP, &phy_data); 3880 if (ret_val) 3881 return ret_val; 3882 3883 if (!(phy_data & NWAY_ER_LP_NWAY_CAPS)) 3884 *duplex = HALF_DUPLEX; 3885 else { 3886 ret_val = e1000_read_phy_reg(hw, 3887 PHY_LP_ABILITY, &phy_data); 3888 if (ret_val) 3889 return ret_val; 3890 if ((*speed == SPEED_100 && 3891 !(phy_data & NWAY_LPAR_100TX_FD_CAPS)) 3892 || (*speed == SPEED_10 3893 && !(phy_data & NWAY_LPAR_10T_FD_CAPS))) 3894 *duplex = HALF_DUPLEX; 3895 } 3896 } 3897 3898 if ((hw->mac_type == e1000_80003es2lan) && 3899 (hw->media_type == e1000_media_type_copper)) { 3900 if (*speed == SPEED_1000) 3901 ret_val = e1000_configure_kmrn_for_1000(hw); 3902 else 3903 ret_val = e1000_configure_kmrn_for_10_100(hw, *duplex); 3904 if (ret_val) 3905 return ret_val; 3906 } 3907 return E1000_SUCCESS; 3908 } 3909 3910 /****************************************************************************** 3911 * Blocks until autoneg completes or times out (~4.5 seconds) 3912 * 3913 * hw - Struct containing variables accessed by shared code 3914 ******************************************************************************/ 3915 static int 3916 e1000_wait_autoneg(struct e1000_hw *hw) 3917 { 3918 uint16_t i; 3919 uint16_t phy_data; 3920 3921 DEBUGFUNC(); 3922 DEBUGOUT("Waiting for Auto-Neg to complete.\n"); 3923 3924 /* We will wait for autoneg to complete or 4.5 seconds to expire. */ 3925 for (i = PHY_AUTO_NEG_TIME; i > 0; i--) { 3926 /* Read the MII Status Register and wait for Auto-Neg 3927 * Complete bit to be set. 3928 */ 3929 if (e1000_read_phy_reg(hw, PHY_STATUS, &phy_data) < 0) { 3930 DEBUGOUT("PHY Read Error\n"); 3931 return -E1000_ERR_PHY; 3932 } 3933 if (e1000_read_phy_reg(hw, PHY_STATUS, &phy_data) < 0) { 3934 DEBUGOUT("PHY Read Error\n"); 3935 return -E1000_ERR_PHY; 3936 } 3937 if (phy_data & MII_SR_AUTONEG_COMPLETE) { 3938 DEBUGOUT("Auto-Neg complete.\n"); 3939 return 0; 3940 } 3941 mdelay(100); 3942 } 3943 DEBUGOUT("Auto-Neg timedout.\n"); 3944 return -E1000_ERR_TIMEOUT; 3945 } 3946 3947 /****************************************************************************** 3948 * Raises the Management Data Clock 3949 * 3950 * hw - Struct containing variables accessed by shared code 3951 * ctrl - Device control register's current value 3952 ******************************************************************************/ 3953 static void 3954 e1000_raise_mdi_clk(struct e1000_hw *hw, uint32_t * ctrl) 3955 { 3956 /* Raise the clock input to the Management Data Clock (by setting the MDC 3957 * bit), and then delay 2 microseconds. 3958 */ 3959 E1000_WRITE_REG(hw, CTRL, (*ctrl | E1000_CTRL_MDC)); 3960 E1000_WRITE_FLUSH(hw); 3961 udelay(2); 3962 } 3963 3964 /****************************************************************************** 3965 * Lowers the Management Data Clock 3966 * 3967 * hw - Struct containing variables accessed by shared code 3968 * ctrl - Device control register's current value 3969 ******************************************************************************/ 3970 static void 3971 e1000_lower_mdi_clk(struct e1000_hw *hw, uint32_t * ctrl) 3972 { 3973 /* Lower the clock input to the Management Data Clock (by clearing the MDC 3974 * bit), and then delay 2 microseconds. 3975 */ 3976 E1000_WRITE_REG(hw, CTRL, (*ctrl & ~E1000_CTRL_MDC)); 3977 E1000_WRITE_FLUSH(hw); 3978 udelay(2); 3979 } 3980 3981 /****************************************************************************** 3982 * Shifts data bits out to the PHY 3983 * 3984 * hw - Struct containing variables accessed by shared code 3985 * data - Data to send out to the PHY 3986 * count - Number of bits to shift out 3987 * 3988 * Bits are shifted out in MSB to LSB order. 3989 ******************************************************************************/ 3990 static void 3991 e1000_shift_out_mdi_bits(struct e1000_hw *hw, uint32_t data, uint16_t count) 3992 { 3993 uint32_t ctrl; 3994 uint32_t mask; 3995 3996 /* We need to shift "count" number of bits out to the PHY. So, the value 3997 * in the "data" parameter will be shifted out to the PHY one bit at a 3998 * time. In order to do this, "data" must be broken down into bits. 3999 */ 4000 mask = 0x01; 4001 mask <<= (count - 1); 4002 4003 ctrl = E1000_READ_REG(hw, CTRL); 4004 4005 /* Set MDIO_DIR and MDC_DIR direction bits to be used as output pins. */ 4006 ctrl |= (E1000_CTRL_MDIO_DIR | E1000_CTRL_MDC_DIR); 4007 4008 while (mask) { 4009 /* A "1" is shifted out to the PHY by setting the MDIO bit to "1" and 4010 * then raising and lowering the Management Data Clock. A "0" is 4011 * shifted out to the PHY by setting the MDIO bit to "0" and then 4012 * raising and lowering the clock. 4013 */ 4014 if (data & mask) 4015 ctrl |= E1000_CTRL_MDIO; 4016 else 4017 ctrl &= ~E1000_CTRL_MDIO; 4018 4019 E1000_WRITE_REG(hw, CTRL, ctrl); 4020 E1000_WRITE_FLUSH(hw); 4021 4022 udelay(2); 4023 4024 e1000_raise_mdi_clk(hw, &ctrl); 4025 e1000_lower_mdi_clk(hw, &ctrl); 4026 4027 mask = mask >> 1; 4028 } 4029 } 4030 4031 /****************************************************************************** 4032 * Shifts data bits in from the PHY 4033 * 4034 * hw - Struct containing variables accessed by shared code 4035 * 4036 * Bits are shifted in in MSB to LSB order. 4037 ******************************************************************************/ 4038 static uint16_t 4039 e1000_shift_in_mdi_bits(struct e1000_hw *hw) 4040 { 4041 uint32_t ctrl; 4042 uint16_t data = 0; 4043 uint8_t i; 4044 4045 /* In order to read a register from the PHY, we need to shift in a total 4046 * of 18 bits from the PHY. The first two bit (turnaround) times are used 4047 * to avoid contention on the MDIO pin when a read operation is performed. 4048 * These two bits are ignored by us and thrown away. Bits are "shifted in" 4049 * by raising the input to the Management Data Clock (setting the MDC bit), 4050 * and then reading the value of the MDIO bit. 4051 */ 4052 ctrl = E1000_READ_REG(hw, CTRL); 4053 4054 /* Clear MDIO_DIR (SWDPIO1) to indicate this bit is to be used as input. */ 4055 ctrl &= ~E1000_CTRL_MDIO_DIR; 4056 ctrl &= ~E1000_CTRL_MDIO; 4057 4058 E1000_WRITE_REG(hw, CTRL, ctrl); 4059 E1000_WRITE_FLUSH(hw); 4060 4061 /* Raise and Lower the clock before reading in the data. This accounts for 4062 * the turnaround bits. The first clock occurred when we clocked out the 4063 * last bit of the Register Address. 4064 */ 4065 e1000_raise_mdi_clk(hw, &ctrl); 4066 e1000_lower_mdi_clk(hw, &ctrl); 4067 4068 for (data = 0, i = 0; i < 16; i++) { 4069 data = data << 1; 4070 e1000_raise_mdi_clk(hw, &ctrl); 4071 ctrl = E1000_READ_REG(hw, CTRL); 4072 /* Check to see if we shifted in a "1". */ 4073 if (ctrl & E1000_CTRL_MDIO) 4074 data |= 1; 4075 e1000_lower_mdi_clk(hw, &ctrl); 4076 } 4077 4078 e1000_raise_mdi_clk(hw, &ctrl); 4079 e1000_lower_mdi_clk(hw, &ctrl); 4080 4081 return data; 4082 } 4083 4084 /***************************************************************************** 4085 * Reads the value from a PHY register 4086 * 4087 * hw - Struct containing variables accessed by shared code 4088 * reg_addr - address of the PHY register to read 4089 ******************************************************************************/ 4090 static int 4091 e1000_read_phy_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t * phy_data) 4092 { 4093 uint32_t i; 4094 uint32_t mdic = 0; 4095 const uint32_t phy_addr = 1; 4096 4097 if (reg_addr > MAX_PHY_REG_ADDRESS) { 4098 DEBUGOUT("PHY Address %d is out of range\n", reg_addr); 4099 return -E1000_ERR_PARAM; 4100 } 4101 4102 if (hw->mac_type > e1000_82543) { 4103 /* Set up Op-code, Phy Address, and register address in the MDI 4104 * Control register. The MAC will take care of interfacing with the 4105 * PHY to retrieve the desired data. 4106 */ 4107 mdic = ((reg_addr << E1000_MDIC_REG_SHIFT) | 4108 (phy_addr << E1000_MDIC_PHY_SHIFT) | 4109 (E1000_MDIC_OP_READ)); 4110 4111 E1000_WRITE_REG(hw, MDIC, mdic); 4112 4113 /* Poll the ready bit to see if the MDI read completed */ 4114 for (i = 0; i < 64; i++) { 4115 udelay(10); 4116 mdic = E1000_READ_REG(hw, MDIC); 4117 if (mdic & E1000_MDIC_READY) 4118 break; 4119 } 4120 if (!(mdic & E1000_MDIC_READY)) { 4121 DEBUGOUT("MDI Read did not complete\n"); 4122 return -E1000_ERR_PHY; 4123 } 4124 if (mdic & E1000_MDIC_ERROR) { 4125 DEBUGOUT("MDI Error\n"); 4126 return -E1000_ERR_PHY; 4127 } 4128 *phy_data = (uint16_t) mdic; 4129 } else { 4130 /* We must first send a preamble through the MDIO pin to signal the 4131 * beginning of an MII instruction. This is done by sending 32 4132 * consecutive "1" bits. 4133 */ 4134 e1000_shift_out_mdi_bits(hw, PHY_PREAMBLE, PHY_PREAMBLE_SIZE); 4135 4136 /* Now combine the next few fields that are required for a read 4137 * operation. We use this method instead of calling the 4138 * e1000_shift_out_mdi_bits routine five different times. The format of 4139 * a MII read instruction consists of a shift out of 14 bits and is 4140 * defined as follows: 4141 * <Preamble><SOF><Op Code><Phy Addr><Reg Addr> 4142 * followed by a shift in of 18 bits. This first two bits shifted in 4143 * are TurnAround bits used to avoid contention on the MDIO pin when a 4144 * READ operation is performed. These two bits are thrown away 4145 * followed by a shift in of 16 bits which contains the desired data. 4146 */ 4147 mdic = ((reg_addr) | (phy_addr << 5) | 4148 (PHY_OP_READ << 10) | (PHY_SOF << 12)); 4149 4150 e1000_shift_out_mdi_bits(hw, mdic, 14); 4151 4152 /* Now that we've shifted out the read command to the MII, we need to 4153 * "shift in" the 16-bit value (18 total bits) of the requested PHY 4154 * register address. 4155 */ 4156 *phy_data = e1000_shift_in_mdi_bits(hw); 4157 } 4158 return 0; 4159 } 4160 4161 /****************************************************************************** 4162 * Writes a value to a PHY register 4163 * 4164 * hw - Struct containing variables accessed by shared code 4165 * reg_addr - address of the PHY register to write 4166 * data - data to write to the PHY 4167 ******************************************************************************/ 4168 static int 4169 e1000_write_phy_reg(struct e1000_hw *hw, uint32_t reg_addr, uint16_t phy_data) 4170 { 4171 uint32_t i; 4172 uint32_t mdic = 0; 4173 const uint32_t phy_addr = 1; 4174 4175 if (reg_addr > MAX_PHY_REG_ADDRESS) { 4176 DEBUGOUT("PHY Address %d is out of range\n", reg_addr); 4177 return -E1000_ERR_PARAM; 4178 } 4179 4180 if (hw->mac_type > e1000_82543) { 4181 /* Set up Op-code, Phy Address, register address, and data intended 4182 * for the PHY register in the MDI Control register. The MAC will take 4183 * care of interfacing with the PHY to send the desired data. 4184 */ 4185 mdic = (((uint32_t) phy_data) | 4186 (reg_addr << E1000_MDIC_REG_SHIFT) | 4187 (phy_addr << E1000_MDIC_PHY_SHIFT) | 4188 (E1000_MDIC_OP_WRITE)); 4189 4190 E1000_WRITE_REG(hw, MDIC, mdic); 4191 4192 /* Poll the ready bit to see if the MDI read completed */ 4193 for (i = 0; i < 64; i++) { 4194 udelay(10); 4195 mdic = E1000_READ_REG(hw, MDIC); 4196 if (mdic & E1000_MDIC_READY) 4197 break; 4198 } 4199 if (!(mdic & E1000_MDIC_READY)) { 4200 DEBUGOUT("MDI Write did not complete\n"); 4201 return -E1000_ERR_PHY; 4202 } 4203 } else { 4204 /* We'll need to use the SW defined pins to shift the write command 4205 * out to the PHY. We first send a preamble to the PHY to signal the 4206 * beginning of the MII instruction. This is done by sending 32 4207 * consecutive "1" bits. 4208 */ 4209 e1000_shift_out_mdi_bits(hw, PHY_PREAMBLE, PHY_PREAMBLE_SIZE); 4210 4211 /* Now combine the remaining required fields that will indicate a 4212 * write operation. We use this method instead of calling the 4213 * e1000_shift_out_mdi_bits routine for each field in the command. The 4214 * format of a MII write instruction is as follows: 4215 * <Preamble><SOF><Op Code><Phy Addr><Reg Addr><Turnaround><Data>. 4216 */ 4217 mdic = ((PHY_TURNAROUND) | (reg_addr << 2) | (phy_addr << 7) | 4218 (PHY_OP_WRITE << 12) | (PHY_SOF << 14)); 4219 mdic <<= 16; 4220 mdic |= (uint32_t) phy_data; 4221 4222 e1000_shift_out_mdi_bits(hw, mdic, 32); 4223 } 4224 return 0; 4225 } 4226 4227 /****************************************************************************** 4228 * Checks if PHY reset is blocked due to SOL/IDER session, for example. 4229 * Returning E1000_BLK_PHY_RESET isn't necessarily an error. But it's up to 4230 * the caller to figure out how to deal with it. 4231 * 4232 * hw - Struct containing variables accessed by shared code 4233 * 4234 * returns: - E1000_BLK_PHY_RESET 4235 * E1000_SUCCESS 4236 * 4237 *****************************************************************************/ 4238 int32_t 4239 e1000_check_phy_reset_block(struct e1000_hw *hw) 4240 { 4241 uint32_t manc = 0; 4242 uint32_t fwsm = 0; 4243 4244 if (hw->mac_type == e1000_ich8lan) { 4245 fwsm = E1000_READ_REG(hw, FWSM); 4246 return (fwsm & E1000_FWSM_RSPCIPHY) ? E1000_SUCCESS 4247 : E1000_BLK_PHY_RESET; 4248 } 4249 4250 if (hw->mac_type > e1000_82547_rev_2) 4251 manc = E1000_READ_REG(hw, MANC); 4252 return (manc & E1000_MANC_BLK_PHY_RST_ON_IDE) ? 4253 E1000_BLK_PHY_RESET : E1000_SUCCESS; 4254 } 4255 4256 /*************************************************************************** 4257 * Checks if the PHY configuration is done 4258 * 4259 * hw: Struct containing variables accessed by shared code 4260 * 4261 * returns: - E1000_ERR_RESET if fail to reset MAC 4262 * E1000_SUCCESS at any other case. 4263 * 4264 ***************************************************************************/ 4265 static int32_t 4266 e1000_get_phy_cfg_done(struct e1000_hw *hw) 4267 { 4268 int32_t timeout = PHY_CFG_TIMEOUT; 4269 uint32_t cfg_mask = E1000_EEPROM_CFG_DONE; 4270 4271 DEBUGFUNC(); 4272 4273 switch (hw->mac_type) { 4274 default: 4275 mdelay(10); 4276 break; 4277 4278 case e1000_80003es2lan: 4279 /* Separate *_CFG_DONE_* bit for each port */ 4280 if (e1000_is_second_port(hw)) 4281 cfg_mask = E1000_EEPROM_CFG_DONE_PORT_1; 4282 /* Fall Through */ 4283 4284 case e1000_82571: 4285 case e1000_82572: 4286 while (timeout) { 4287 if (E1000_READ_REG(hw, EEMNGCTL) & cfg_mask) 4288 break; 4289 else 4290 mdelay(1); 4291 timeout--; 4292 } 4293 if (!timeout) { 4294 DEBUGOUT("MNG configuration cycle has not " 4295 "completed.\n"); 4296 return -E1000_ERR_RESET; 4297 } 4298 break; 4299 } 4300 4301 return E1000_SUCCESS; 4302 } 4303 4304 /****************************************************************************** 4305 * Returns the PHY to the power-on reset state 4306 * 4307 * hw - Struct containing variables accessed by shared code 4308 ******************************************************************************/ 4309 int32_t 4310 e1000_phy_hw_reset(struct e1000_hw *hw) 4311 { 4312 uint16_t swfw = E1000_SWFW_PHY0_SM; 4313 uint32_t ctrl, ctrl_ext; 4314 uint32_t led_ctrl; 4315 int32_t ret_val; 4316 4317 DEBUGFUNC(); 4318 4319 /* In the case of the phy reset being blocked, it's not an error, we 4320 * simply return success without performing the reset. */ 4321 ret_val = e1000_check_phy_reset_block(hw); 4322 if (ret_val) 4323 return E1000_SUCCESS; 4324 4325 DEBUGOUT("Resetting Phy...\n"); 4326 4327 if (hw->mac_type > e1000_82543) { 4328 if (e1000_is_second_port(hw)) 4329 swfw = E1000_SWFW_PHY1_SM; 4330 4331 if (e1000_swfw_sync_acquire(hw, swfw)) { 4332 DEBUGOUT("Unable to acquire swfw sync\n"); 4333 return -E1000_ERR_SWFW_SYNC; 4334 } 4335 4336 /* Read the device control register and assert the E1000_CTRL_PHY_RST 4337 * bit. Then, take it out of reset. 4338 */ 4339 ctrl = E1000_READ_REG(hw, CTRL); 4340 E1000_WRITE_REG(hw, CTRL, ctrl | E1000_CTRL_PHY_RST); 4341 E1000_WRITE_FLUSH(hw); 4342 4343 if (hw->mac_type < e1000_82571) 4344 udelay(10); 4345 else 4346 udelay(100); 4347 4348 E1000_WRITE_REG(hw, CTRL, ctrl); 4349 E1000_WRITE_FLUSH(hw); 4350 4351 if (hw->mac_type >= e1000_82571) 4352 mdelay(10); 4353 4354 } else { 4355 /* Read the Extended Device Control Register, assert the PHY_RESET_DIR 4356 * bit to put the PHY into reset. Then, take it out of reset. 4357 */ 4358 ctrl_ext = E1000_READ_REG(hw, CTRL_EXT); 4359 ctrl_ext |= E1000_CTRL_EXT_SDP4_DIR; 4360 ctrl_ext &= ~E1000_CTRL_EXT_SDP4_DATA; 4361 E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext); 4362 E1000_WRITE_FLUSH(hw); 4363 mdelay(10); 4364 ctrl_ext |= E1000_CTRL_EXT_SDP4_DATA; 4365 E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext); 4366 E1000_WRITE_FLUSH(hw); 4367 } 4368 udelay(150); 4369 4370 if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) { 4371 /* Configure activity LED after PHY reset */ 4372 led_ctrl = E1000_READ_REG(hw, LEDCTL); 4373 led_ctrl &= IGP_ACTIVITY_LED_MASK; 4374 led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE); 4375 E1000_WRITE_REG(hw, LEDCTL, led_ctrl); 4376 } 4377 4378 /* Wait for FW to finish PHY configuration. */ 4379 ret_val = e1000_get_phy_cfg_done(hw); 4380 if (ret_val != E1000_SUCCESS) 4381 return ret_val; 4382 4383 return ret_val; 4384 } 4385 4386 /****************************************************************************** 4387 * IGP phy init script - initializes the GbE PHY 4388 * 4389 * hw - Struct containing variables accessed by shared code 4390 *****************************************************************************/ 4391 static void 4392 e1000_phy_init_script(struct e1000_hw *hw) 4393 { 4394 uint32_t ret_val; 4395 uint16_t phy_saved_data; 4396 DEBUGFUNC(); 4397 4398 if (hw->phy_init_script) { 4399 mdelay(20); 4400 4401 /* Save off the current value of register 0x2F5B to be 4402 * restored at the end of this routine. */ 4403 ret_val = e1000_read_phy_reg(hw, 0x2F5B, &phy_saved_data); 4404 4405 /* Disabled the PHY transmitter */ 4406 e1000_write_phy_reg(hw, 0x2F5B, 0x0003); 4407 4408 mdelay(20); 4409 4410 e1000_write_phy_reg(hw, 0x0000, 0x0140); 4411 4412 mdelay(5); 4413 4414 switch (hw->mac_type) { 4415 case e1000_82541: 4416 case e1000_82547: 4417 e1000_write_phy_reg(hw, 0x1F95, 0x0001); 4418 4419 e1000_write_phy_reg(hw, 0x1F71, 0xBD21); 4420 4421 e1000_write_phy_reg(hw, 0x1F79, 0x0018); 4422 4423 e1000_write_phy_reg(hw, 0x1F30, 0x1600); 4424 4425 e1000_write_phy_reg(hw, 0x1F31, 0x0014); 4426 4427 e1000_write_phy_reg(hw, 0x1F32, 0x161C); 4428 4429 e1000_write_phy_reg(hw, 0x1F94, 0x0003); 4430 4431 e1000_write_phy_reg(hw, 0x1F96, 0x003F); 4432 4433 e1000_write_phy_reg(hw, 0x2010, 0x0008); 4434 break; 4435 4436 case e1000_82541_rev_2: 4437 case e1000_82547_rev_2: 4438 e1000_write_phy_reg(hw, 0x1F73, 0x0099); 4439 break; 4440 default: 4441 break; 4442 } 4443 4444 e1000_write_phy_reg(hw, 0x0000, 0x3300); 4445 4446 mdelay(20); 4447 4448 /* Now enable the transmitter */ 4449 if (!ret_val) 4450 e1000_write_phy_reg(hw, 0x2F5B, phy_saved_data); 4451 4452 if (hw->mac_type == e1000_82547) { 4453 uint16_t fused, fine, coarse; 4454 4455 /* Move to analog registers page */ 4456 e1000_read_phy_reg(hw, 4457 IGP01E1000_ANALOG_SPARE_FUSE_STATUS, &fused); 4458 4459 if (!(fused & IGP01E1000_ANALOG_SPARE_FUSE_ENABLED)) { 4460 e1000_read_phy_reg(hw, 4461 IGP01E1000_ANALOG_FUSE_STATUS, &fused); 4462 4463 fine = fused & IGP01E1000_ANALOG_FUSE_FINE_MASK; 4464 coarse = fused 4465 & IGP01E1000_ANALOG_FUSE_COARSE_MASK; 4466 4467 if (coarse > 4468 IGP01E1000_ANALOG_FUSE_COARSE_THRESH) { 4469 coarse -= 4470 IGP01E1000_ANALOG_FUSE_COARSE_10; 4471 fine -= IGP01E1000_ANALOG_FUSE_FINE_1; 4472 } else if (coarse 4473 == IGP01E1000_ANALOG_FUSE_COARSE_THRESH) 4474 fine -= IGP01E1000_ANALOG_FUSE_FINE_10; 4475 4476 fused = (fused 4477 & IGP01E1000_ANALOG_FUSE_POLY_MASK) | 4478 (fine 4479 & IGP01E1000_ANALOG_FUSE_FINE_MASK) | 4480 (coarse 4481 & IGP01E1000_ANALOG_FUSE_COARSE_MASK); 4482 4483 e1000_write_phy_reg(hw, 4484 IGP01E1000_ANALOG_FUSE_CONTROL, fused); 4485 e1000_write_phy_reg(hw, 4486 IGP01E1000_ANALOG_FUSE_BYPASS, 4487 IGP01E1000_ANALOG_FUSE_ENABLE_SW_CONTROL); 4488 } 4489 } 4490 } 4491 } 4492 4493 /****************************************************************************** 4494 * Resets the PHY 4495 * 4496 * hw - Struct containing variables accessed by shared code 4497 * 4498 * Sets bit 15 of the MII Control register 4499 ******************************************************************************/ 4500 int32_t 4501 e1000_phy_reset(struct e1000_hw *hw) 4502 { 4503 int32_t ret_val; 4504 uint16_t phy_data; 4505 4506 DEBUGFUNC(); 4507 4508 /* In the case of the phy reset being blocked, it's not an error, we 4509 * simply return success without performing the reset. */ 4510 ret_val = e1000_check_phy_reset_block(hw); 4511 if (ret_val) 4512 return E1000_SUCCESS; 4513 4514 switch (hw->phy_type) { 4515 case e1000_phy_igp: 4516 case e1000_phy_igp_2: 4517 case e1000_phy_igp_3: 4518 case e1000_phy_ife: 4519 ret_val = e1000_phy_hw_reset(hw); 4520 if (ret_val) 4521 return ret_val; 4522 break; 4523 default: 4524 ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data); 4525 if (ret_val) 4526 return ret_val; 4527 4528 phy_data |= MII_CR_RESET; 4529 ret_val = e1000_write_phy_reg(hw, PHY_CTRL, phy_data); 4530 if (ret_val) 4531 return ret_val; 4532 4533 udelay(1); 4534 break; 4535 } 4536 4537 if (hw->phy_type == e1000_phy_igp || hw->phy_type == e1000_phy_igp_2) 4538 e1000_phy_init_script(hw); 4539 4540 return E1000_SUCCESS; 4541 } 4542 4543 static int e1000_set_phy_type (struct e1000_hw *hw) 4544 { 4545 DEBUGFUNC (); 4546 4547 if (hw->mac_type == e1000_undefined) 4548 return -E1000_ERR_PHY_TYPE; 4549 4550 switch (hw->phy_id) { 4551 case M88E1000_E_PHY_ID: 4552 case M88E1000_I_PHY_ID: 4553 case M88E1011_I_PHY_ID: 4554 case M88E1111_I_PHY_ID: 4555 hw->phy_type = e1000_phy_m88; 4556 break; 4557 case IGP01E1000_I_PHY_ID: 4558 if (hw->mac_type == e1000_82541 || 4559 hw->mac_type == e1000_82541_rev_2 || 4560 hw->mac_type == e1000_82547 || 4561 hw->mac_type == e1000_82547_rev_2) { 4562 hw->phy_type = e1000_phy_igp; 4563 hw->phy_type = e1000_phy_igp; 4564 break; 4565 } 4566 case IGP03E1000_E_PHY_ID: 4567 hw->phy_type = e1000_phy_igp_3; 4568 break; 4569 case IFE_E_PHY_ID: 4570 case IFE_PLUS_E_PHY_ID: 4571 case IFE_C_E_PHY_ID: 4572 hw->phy_type = e1000_phy_ife; 4573 break; 4574 case GG82563_E_PHY_ID: 4575 if (hw->mac_type == e1000_80003es2lan) { 4576 hw->phy_type = e1000_phy_gg82563; 4577 break; 4578 } 4579 case BME1000_E_PHY_ID: 4580 hw->phy_type = e1000_phy_bm; 4581 break; 4582 /* Fall Through */ 4583 default: 4584 /* Should never have loaded on this device */ 4585 hw->phy_type = e1000_phy_undefined; 4586 return -E1000_ERR_PHY_TYPE; 4587 } 4588 4589 return E1000_SUCCESS; 4590 } 4591 4592 /****************************************************************************** 4593 * Probes the expected PHY address for known PHY IDs 4594 * 4595 * hw - Struct containing variables accessed by shared code 4596 ******************************************************************************/ 4597 static int32_t 4598 e1000_detect_gig_phy(struct e1000_hw *hw) 4599 { 4600 int32_t phy_init_status, ret_val; 4601 uint16_t phy_id_high, phy_id_low; 4602 boolean_t match = FALSE; 4603 4604 DEBUGFUNC(); 4605 4606 /* The 82571 firmware may still be configuring the PHY. In this 4607 * case, we cannot access the PHY until the configuration is done. So 4608 * we explicitly set the PHY values. */ 4609 if (hw->mac_type == e1000_82571 || 4610 hw->mac_type == e1000_82572) { 4611 hw->phy_id = IGP01E1000_I_PHY_ID; 4612 hw->phy_type = e1000_phy_igp_2; 4613 return E1000_SUCCESS; 4614 } 4615 4616 /* ESB-2 PHY reads require e1000_phy_gg82563 to be set because of a 4617 * work- around that forces PHY page 0 to be set or the reads fail. 4618 * The rest of the code in this routine uses e1000_read_phy_reg to 4619 * read the PHY ID. So for ESB-2 we need to have this set so our 4620 * reads won't fail. If the attached PHY is not a e1000_phy_gg82563, 4621 * the routines below will figure this out as well. */ 4622 if (hw->mac_type == e1000_80003es2lan) 4623 hw->phy_type = e1000_phy_gg82563; 4624 4625 /* Read the PHY ID Registers to identify which PHY is onboard. */ 4626 ret_val = e1000_read_phy_reg(hw, PHY_ID1, &phy_id_high); 4627 if (ret_val) 4628 return ret_val; 4629 4630 hw->phy_id = (uint32_t) (phy_id_high << 16); 4631 udelay(20); 4632 ret_val = e1000_read_phy_reg(hw, PHY_ID2, &phy_id_low); 4633 if (ret_val) 4634 return ret_val; 4635 4636 hw->phy_id |= (uint32_t) (phy_id_low & PHY_REVISION_MASK); 4637 hw->phy_revision = (uint32_t) phy_id_low & ~PHY_REVISION_MASK; 4638 4639 switch (hw->mac_type) { 4640 case e1000_82543: 4641 if (hw->phy_id == M88E1000_E_PHY_ID) 4642 match = TRUE; 4643 break; 4644 case e1000_82544: 4645 if (hw->phy_id == M88E1000_I_PHY_ID) 4646 match = TRUE; 4647 break; 4648 case e1000_82540: 4649 case e1000_82545: 4650 case e1000_82545_rev_3: 4651 case e1000_82546: 4652 case e1000_82546_rev_3: 4653 if (hw->phy_id == M88E1011_I_PHY_ID) 4654 match = TRUE; 4655 break; 4656 case e1000_82541: 4657 case e1000_82541_rev_2: 4658 case e1000_82547: 4659 case e1000_82547_rev_2: 4660 if(hw->phy_id == IGP01E1000_I_PHY_ID) 4661 match = TRUE; 4662 4663 break; 4664 case e1000_82573: 4665 if (hw->phy_id == M88E1111_I_PHY_ID) 4666 match = TRUE; 4667 break; 4668 case e1000_82574: 4669 if (hw->phy_id == BME1000_E_PHY_ID) 4670 match = TRUE; 4671 break; 4672 case e1000_80003es2lan: 4673 if (hw->phy_id == GG82563_E_PHY_ID) 4674 match = TRUE; 4675 break; 4676 case e1000_ich8lan: 4677 if (hw->phy_id == IGP03E1000_E_PHY_ID) 4678 match = TRUE; 4679 if (hw->phy_id == IFE_E_PHY_ID) 4680 match = TRUE; 4681 if (hw->phy_id == IFE_PLUS_E_PHY_ID) 4682 match = TRUE; 4683 if (hw->phy_id == IFE_C_E_PHY_ID) 4684 match = TRUE; 4685 break; 4686 default: 4687 DEBUGOUT("Invalid MAC type %d\n", hw->mac_type); 4688 return -E1000_ERR_CONFIG; 4689 } 4690 4691 phy_init_status = e1000_set_phy_type(hw); 4692 4693 if ((match) && (phy_init_status == E1000_SUCCESS)) { 4694 DEBUGOUT("PHY ID 0x%X detected\n", hw->phy_id); 4695 return 0; 4696 } 4697 DEBUGOUT("Invalid PHY ID 0x%X\n", hw->phy_id); 4698 return -E1000_ERR_PHY; 4699 } 4700 4701 /***************************************************************************** 4702 * Set media type and TBI compatibility. 4703 * 4704 * hw - Struct containing variables accessed by shared code 4705 * **************************************************************************/ 4706 void 4707 e1000_set_media_type(struct e1000_hw *hw) 4708 { 4709 uint32_t status; 4710 4711 DEBUGFUNC(); 4712 4713 if (hw->mac_type != e1000_82543) { 4714 /* tbi_compatibility is only valid on 82543 */ 4715 hw->tbi_compatibility_en = FALSE; 4716 } 4717 4718 switch (hw->device_id) { 4719 case E1000_DEV_ID_82545GM_SERDES: 4720 case E1000_DEV_ID_82546GB_SERDES: 4721 case E1000_DEV_ID_82571EB_SERDES: 4722 case E1000_DEV_ID_82571EB_SERDES_DUAL: 4723 case E1000_DEV_ID_82571EB_SERDES_QUAD: 4724 case E1000_DEV_ID_82572EI_SERDES: 4725 case E1000_DEV_ID_80003ES2LAN_SERDES_DPT: 4726 hw->media_type = e1000_media_type_internal_serdes; 4727 break; 4728 default: 4729 switch (hw->mac_type) { 4730 case e1000_82542_rev2_0: 4731 case e1000_82542_rev2_1: 4732 hw->media_type = e1000_media_type_fiber; 4733 break; 4734 case e1000_ich8lan: 4735 case e1000_82573: 4736 case e1000_82574: 4737 /* The STATUS_TBIMODE bit is reserved or reused 4738 * for the this device. 4739 */ 4740 hw->media_type = e1000_media_type_copper; 4741 break; 4742 default: 4743 status = E1000_READ_REG(hw, STATUS); 4744 if (status & E1000_STATUS_TBIMODE) { 4745 hw->media_type = e1000_media_type_fiber; 4746 /* tbi_compatibility not valid on fiber */ 4747 hw->tbi_compatibility_en = FALSE; 4748 } else { 4749 hw->media_type = e1000_media_type_copper; 4750 } 4751 break; 4752 } 4753 } 4754 } 4755 4756 /** 4757 * e1000_sw_init - Initialize general software structures (struct e1000_adapter) 4758 * 4759 * e1000_sw_init initializes the Adapter private data structure. 4760 * Fields are initialized based on PCI device information and 4761 * OS network device settings (MTU size). 4762 **/ 4763 4764 static int 4765 e1000_sw_init(struct eth_device *nic) 4766 { 4767 struct e1000_hw *hw = (typeof(hw)) nic->priv; 4768 int result; 4769 4770 /* PCI config space info */ 4771 pci_read_config_word(hw->pdev, PCI_VENDOR_ID, &hw->vendor_id); 4772 pci_read_config_word(hw->pdev, PCI_DEVICE_ID, &hw->device_id); 4773 pci_read_config_word(hw->pdev, PCI_SUBSYSTEM_VENDOR_ID, 4774 &hw->subsystem_vendor_id); 4775 pci_read_config_word(hw->pdev, PCI_SUBSYSTEM_ID, &hw->subsystem_id); 4776 4777 pci_read_config_byte(hw->pdev, PCI_REVISION_ID, &hw->revision_id); 4778 pci_read_config_word(hw->pdev, PCI_COMMAND, &hw->pci_cmd_word); 4779 4780 /* identify the MAC */ 4781 result = e1000_set_mac_type(hw); 4782 if (result) { 4783 E1000_ERR(hw->nic, "Unknown MAC Type\n"); 4784 return result; 4785 } 4786 4787 switch (hw->mac_type) { 4788 default: 4789 break; 4790 case e1000_82541: 4791 case e1000_82547: 4792 case e1000_82541_rev_2: 4793 case e1000_82547_rev_2: 4794 hw->phy_init_script = 1; 4795 break; 4796 } 4797 4798 /* flow control settings */ 4799 hw->fc_high_water = E1000_FC_HIGH_THRESH; 4800 hw->fc_low_water = E1000_FC_LOW_THRESH; 4801 hw->fc_pause_time = E1000_FC_PAUSE_TIME; 4802 hw->fc_send_xon = 1; 4803 4804 /* Media type - copper or fiber */ 4805 e1000_set_media_type(hw); 4806 4807 if (hw->mac_type >= e1000_82543) { 4808 uint32_t status = E1000_READ_REG(hw, STATUS); 4809 4810 if (status & E1000_STATUS_TBIMODE) { 4811 DEBUGOUT("fiber interface\n"); 4812 hw->media_type = e1000_media_type_fiber; 4813 } else { 4814 DEBUGOUT("copper interface\n"); 4815 hw->media_type = e1000_media_type_copper; 4816 } 4817 } else { 4818 hw->media_type = e1000_media_type_fiber; 4819 } 4820 4821 hw->tbi_compatibility_en = TRUE; 4822 hw->wait_autoneg_complete = TRUE; 4823 if (hw->mac_type < e1000_82543) 4824 hw->report_tx_early = 0; 4825 else 4826 hw->report_tx_early = 1; 4827 4828 return E1000_SUCCESS; 4829 } 4830 4831 void 4832 fill_rx(struct e1000_hw *hw) 4833 { 4834 struct e1000_rx_desc *rd; 4835 4836 rx_last = rx_tail; 4837 rd = rx_base + rx_tail; 4838 rx_tail = (rx_tail + 1) % 8; 4839 memset(rd, 0, 16); 4840 rd->buffer_addr = cpu_to_le64((u32) & packet); 4841 E1000_WRITE_REG(hw, RDT, rx_tail); 4842 } 4843 4844 /** 4845 * e1000_configure_tx - Configure 8254x Transmit Unit after Reset 4846 * @adapter: board private structure 4847 * 4848 * Configure the Tx unit of the MAC after a reset. 4849 **/ 4850 4851 static void 4852 e1000_configure_tx(struct e1000_hw *hw) 4853 { 4854 unsigned long ptr; 4855 unsigned long tctl; 4856 unsigned long tipg, tarc; 4857 uint32_t ipgr1, ipgr2; 4858 4859 ptr = (u32) tx_pool; 4860 if (ptr & 0xf) 4861 ptr = (ptr + 0x10) & (~0xf); 4862 4863 tx_base = (typeof(tx_base)) ptr; 4864 4865 E1000_WRITE_REG(hw, TDBAL, (u32) tx_base); 4866 E1000_WRITE_REG(hw, TDBAH, 0); 4867 4868 E1000_WRITE_REG(hw, TDLEN, 128); 4869 4870 /* Setup the HW Tx Head and Tail descriptor pointers */ 4871 E1000_WRITE_REG(hw, TDH, 0); 4872 E1000_WRITE_REG(hw, TDT, 0); 4873 tx_tail = 0; 4874 4875 /* Set the default values for the Tx Inter Packet Gap timer */ 4876 if (hw->mac_type <= e1000_82547_rev_2 && 4877 (hw->media_type == e1000_media_type_fiber || 4878 hw->media_type == e1000_media_type_internal_serdes)) 4879 tipg = DEFAULT_82543_TIPG_IPGT_FIBER; 4880 else 4881 tipg = DEFAULT_82543_TIPG_IPGT_COPPER; 4882 4883 /* Set the default values for the Tx Inter Packet Gap timer */ 4884 switch (hw->mac_type) { 4885 case e1000_82542_rev2_0: 4886 case e1000_82542_rev2_1: 4887 tipg = DEFAULT_82542_TIPG_IPGT; 4888 ipgr1 = DEFAULT_82542_TIPG_IPGR1; 4889 ipgr2 = DEFAULT_82542_TIPG_IPGR2; 4890 break; 4891 case e1000_80003es2lan: 4892 ipgr1 = DEFAULT_82543_TIPG_IPGR1; 4893 ipgr2 = DEFAULT_80003ES2LAN_TIPG_IPGR2; 4894 break; 4895 default: 4896 ipgr1 = DEFAULT_82543_TIPG_IPGR1; 4897 ipgr2 = DEFAULT_82543_TIPG_IPGR2; 4898 break; 4899 } 4900 tipg |= ipgr1 << E1000_TIPG_IPGR1_SHIFT; 4901 tipg |= ipgr2 << E1000_TIPG_IPGR2_SHIFT; 4902 E1000_WRITE_REG(hw, TIPG, tipg); 4903 /* Program the Transmit Control Register */ 4904 tctl = E1000_READ_REG(hw, TCTL); 4905 tctl &= ~E1000_TCTL_CT; 4906 tctl |= E1000_TCTL_EN | E1000_TCTL_PSP | 4907 (E1000_COLLISION_THRESHOLD << E1000_CT_SHIFT); 4908 4909 if (hw->mac_type == e1000_82571 || hw->mac_type == e1000_82572) { 4910 tarc = E1000_READ_REG(hw, TARC0); 4911 /* set the speed mode bit, we'll clear it if we're not at 4912 * gigabit link later */ 4913 /* git bit can be set to 1*/ 4914 } else if (hw->mac_type == e1000_80003es2lan) { 4915 tarc = E1000_READ_REG(hw, TARC0); 4916 tarc |= 1; 4917 E1000_WRITE_REG(hw, TARC0, tarc); 4918 tarc = E1000_READ_REG(hw, TARC1); 4919 tarc |= 1; 4920 E1000_WRITE_REG(hw, TARC1, tarc); 4921 } 4922 4923 4924 e1000_config_collision_dist(hw); 4925 /* Setup Transmit Descriptor Settings for eop descriptor */ 4926 hw->txd_cmd = E1000_TXD_CMD_EOP | E1000_TXD_CMD_IFCS; 4927 4928 /* Need to set up RS bit */ 4929 if (hw->mac_type < e1000_82543) 4930 hw->txd_cmd |= E1000_TXD_CMD_RPS; 4931 else 4932 hw->txd_cmd |= E1000_TXD_CMD_RS; 4933 E1000_WRITE_REG(hw, TCTL, tctl); 4934 } 4935 4936 /** 4937 * e1000_setup_rctl - configure the receive control register 4938 * @adapter: Board private structure 4939 **/ 4940 static void 4941 e1000_setup_rctl(struct e1000_hw *hw) 4942 { 4943 uint32_t rctl; 4944 4945 rctl = E1000_READ_REG(hw, RCTL); 4946 4947 rctl &= ~(3 << E1000_RCTL_MO_SHIFT); 4948 4949 rctl |= E1000_RCTL_EN | E1000_RCTL_BAM | E1000_RCTL_LBM_NO 4950 | E1000_RCTL_RDMTS_HALF; /* | 4951 (hw.mc_filter_type << E1000_RCTL_MO_SHIFT); */ 4952 4953 if (hw->tbi_compatibility_on == 1) 4954 rctl |= E1000_RCTL_SBP; 4955 else 4956 rctl &= ~E1000_RCTL_SBP; 4957 4958 rctl &= ~(E1000_RCTL_SZ_4096); 4959 rctl |= E1000_RCTL_SZ_2048; 4960 rctl &= ~(E1000_RCTL_BSEX | E1000_RCTL_LPE); 4961 E1000_WRITE_REG(hw, RCTL, rctl); 4962 } 4963 4964 /** 4965 * e1000_configure_rx - Configure 8254x Receive Unit after Reset 4966 * @adapter: board private structure 4967 * 4968 * Configure the Rx unit of the MAC after a reset. 4969 **/ 4970 static void 4971 e1000_configure_rx(struct e1000_hw *hw) 4972 { 4973 unsigned long ptr; 4974 unsigned long rctl, ctrl_ext; 4975 rx_tail = 0; 4976 /* make sure receives are disabled while setting up the descriptors */ 4977 rctl = E1000_READ_REG(hw, RCTL); 4978 E1000_WRITE_REG(hw, RCTL, rctl & ~E1000_RCTL_EN); 4979 if (hw->mac_type >= e1000_82540) { 4980 /* Set the interrupt throttling rate. Value is calculated 4981 * as DEFAULT_ITR = 1/(MAX_INTS_PER_SEC * 256ns) */ 4982 #define MAX_INTS_PER_SEC 8000 4983 #define DEFAULT_ITR 1000000000/(MAX_INTS_PER_SEC * 256) 4984 E1000_WRITE_REG(hw, ITR, DEFAULT_ITR); 4985 } 4986 4987 if (hw->mac_type >= e1000_82571) { 4988 ctrl_ext = E1000_READ_REG(hw, CTRL_EXT); 4989 /* Reset delay timers after every interrupt */ 4990 ctrl_ext |= E1000_CTRL_EXT_INT_TIMER_CLR; 4991 E1000_WRITE_REG(hw, CTRL_EXT, ctrl_ext); 4992 E1000_WRITE_FLUSH(hw); 4993 } 4994 /* Setup the Base and Length of the Rx Descriptor Ring */ 4995 ptr = (u32) rx_pool; 4996 if (ptr & 0xf) 4997 ptr = (ptr + 0x10) & (~0xf); 4998 rx_base = (typeof(rx_base)) ptr; 4999 E1000_WRITE_REG(hw, RDBAL, (u32) rx_base); 5000 E1000_WRITE_REG(hw, RDBAH, 0); 5001 5002 E1000_WRITE_REG(hw, RDLEN, 128); 5003 5004 /* Setup the HW Rx Head and Tail Descriptor Pointers */ 5005 E1000_WRITE_REG(hw, RDH, 0); 5006 E1000_WRITE_REG(hw, RDT, 0); 5007 /* Enable Receives */ 5008 5009 E1000_WRITE_REG(hw, RCTL, rctl); 5010 fill_rx(hw); 5011 } 5012 5013 /************************************************************************** 5014 POLL - Wait for a frame 5015 ***************************************************************************/ 5016 static int 5017 e1000_poll(struct eth_device *nic) 5018 { 5019 struct e1000_hw *hw = nic->priv; 5020 struct e1000_rx_desc *rd; 5021 /* return true if there's an ethernet packet ready to read */ 5022 rd = rx_base + rx_last; 5023 if (!(le32_to_cpu(rd->status)) & E1000_RXD_STAT_DD) 5024 return 0; 5025 /*DEBUGOUT("recv: packet len=%d \n", rd->length); */ 5026 NetReceive((uchar *)packet, le32_to_cpu(rd->length)); 5027 fill_rx(hw); 5028 return 1; 5029 } 5030 5031 /************************************************************************** 5032 TRANSMIT - Transmit a frame 5033 ***************************************************************************/ 5034 static int 5035 e1000_transmit(struct eth_device *nic, volatile void *packet, int length) 5036 { 5037 void * nv_packet = (void *)packet; 5038 struct e1000_hw *hw = nic->priv; 5039 struct e1000_tx_desc *txp; 5040 int i = 0; 5041 5042 txp = tx_base + tx_tail; 5043 tx_tail = (tx_tail + 1) % 8; 5044 5045 txp->buffer_addr = cpu_to_le64(virt_to_bus(hw->pdev, nv_packet)); 5046 txp->lower.data = cpu_to_le32(hw->txd_cmd | length); 5047 txp->upper.data = 0; 5048 E1000_WRITE_REG(hw, TDT, tx_tail); 5049 5050 E1000_WRITE_FLUSH(hw); 5051 while (!(le32_to_cpu(txp->upper.data) & E1000_TXD_STAT_DD)) { 5052 if (i++ > TOUT_LOOP) { 5053 DEBUGOUT("e1000: tx timeout\n"); 5054 return 0; 5055 } 5056 udelay(10); /* give the nic a chance to write to the register */ 5057 } 5058 return 1; 5059 } 5060 5061 /*reset function*/ 5062 static inline int 5063 e1000_reset(struct eth_device *nic) 5064 { 5065 struct e1000_hw *hw = nic->priv; 5066 5067 e1000_reset_hw(hw); 5068 if (hw->mac_type >= e1000_82544) { 5069 E1000_WRITE_REG(hw, WUC, 0); 5070 } 5071 return e1000_init_hw(nic); 5072 } 5073 5074 /************************************************************************** 5075 DISABLE - Turn off ethernet interface 5076 ***************************************************************************/ 5077 static void 5078 e1000_disable(struct eth_device *nic) 5079 { 5080 struct e1000_hw *hw = nic->priv; 5081 5082 /* Turn off the ethernet interface */ 5083 E1000_WRITE_REG(hw, RCTL, 0); 5084 E1000_WRITE_REG(hw, TCTL, 0); 5085 5086 /* Clear the transmit ring */ 5087 E1000_WRITE_REG(hw, TDH, 0); 5088 E1000_WRITE_REG(hw, TDT, 0); 5089 5090 /* Clear the receive ring */ 5091 E1000_WRITE_REG(hw, RDH, 0); 5092 E1000_WRITE_REG(hw, RDT, 0); 5093 5094 /* put the card in its initial state */ 5095 #if 0 5096 E1000_WRITE_REG(hw, CTRL, E1000_CTRL_RST); 5097 #endif 5098 mdelay(10); 5099 5100 } 5101 5102 /************************************************************************** 5103 INIT - set up ethernet interface(s) 5104 ***************************************************************************/ 5105 static int 5106 e1000_init(struct eth_device *nic, bd_t * bis) 5107 { 5108 struct e1000_hw *hw = nic->priv; 5109 int ret_val = 0; 5110 5111 ret_val = e1000_reset(nic); 5112 if (ret_val < 0) { 5113 if ((ret_val == -E1000_ERR_NOLINK) || 5114 (ret_val == -E1000_ERR_TIMEOUT)) { 5115 E1000_ERR(hw->nic, "Valid Link not detected\n"); 5116 } else { 5117 E1000_ERR(hw->nic, "Hardware Initialization Failed\n"); 5118 } 5119 return 0; 5120 } 5121 e1000_configure_tx(hw); 5122 e1000_setup_rctl(hw); 5123 e1000_configure_rx(hw); 5124 return 1; 5125 } 5126 5127 /****************************************************************************** 5128 * Gets the current PCI bus type of hardware 5129 * 5130 * hw - Struct containing variables accessed by shared code 5131 *****************************************************************************/ 5132 void e1000_get_bus_type(struct e1000_hw *hw) 5133 { 5134 uint32_t status; 5135 5136 switch (hw->mac_type) { 5137 case e1000_82542_rev2_0: 5138 case e1000_82542_rev2_1: 5139 hw->bus_type = e1000_bus_type_pci; 5140 break; 5141 case e1000_82571: 5142 case e1000_82572: 5143 case e1000_82573: 5144 case e1000_82574: 5145 case e1000_80003es2lan: 5146 hw->bus_type = e1000_bus_type_pci_express; 5147 break; 5148 case e1000_ich8lan: 5149 hw->bus_type = e1000_bus_type_pci_express; 5150 break; 5151 default: 5152 status = E1000_READ_REG(hw, STATUS); 5153 hw->bus_type = (status & E1000_STATUS_PCIX_MODE) ? 5154 e1000_bus_type_pcix : e1000_bus_type_pci; 5155 break; 5156 } 5157 } 5158 5159 /* A list of all registered e1000 devices */ 5160 static LIST_HEAD(e1000_hw_list); 5161 5162 /************************************************************************** 5163 PROBE - Look for an adapter, this routine's visible to the outside 5164 You should omit the last argument struct pci_device * for a non-PCI NIC 5165 ***************************************************************************/ 5166 int 5167 e1000_initialize(bd_t * bis) 5168 { 5169 unsigned int i; 5170 pci_dev_t devno; 5171 5172 DEBUGFUNC(); 5173 5174 /* Find and probe all the matching PCI devices */ 5175 for (i = 0; (devno = pci_find_devices(e1000_supported, i)) >= 0; i++) { 5176 u32 val; 5177 5178 /* 5179 * These will never get freed due to errors, this allows us to 5180 * perform SPI EEPROM programming from U-boot, for example. 5181 */ 5182 struct eth_device *nic = malloc(sizeof(*nic)); 5183 struct e1000_hw *hw = malloc(sizeof(*hw)); 5184 if (!nic || !hw) { 5185 printf("e1000#%u: Out of Memory!\n", i); 5186 free(nic); 5187 free(hw); 5188 continue; 5189 } 5190 5191 /* Make sure all of the fields are initially zeroed */ 5192 memset(nic, 0, sizeof(*nic)); 5193 memset(hw, 0, sizeof(*hw)); 5194 5195 /* Assign the passed-in values */ 5196 hw->cardnum = i; 5197 hw->pdev = devno; 5198 hw->nic = nic; 5199 nic->priv = hw; 5200 5201 /* Generate a card name */ 5202 sprintf(nic->name, "e1000#%u", hw->cardnum); 5203 5204 /* Print a debug message with the IO base address */ 5205 pci_read_config_dword(devno, PCI_BASE_ADDRESS_0, &val); 5206 E1000_DBG(nic, "iobase 0x%08x\n", val & 0xfffffff0); 5207 5208 /* Try to enable I/O accesses and bus-mastering */ 5209 val = PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER; 5210 pci_write_config_dword(devno, PCI_COMMAND, val); 5211 5212 /* Make sure it worked */ 5213 pci_read_config_dword(devno, PCI_COMMAND, &val); 5214 if (!(val & PCI_COMMAND_MEMORY)) { 5215 E1000_ERR(nic, "Can't enable I/O memory\n"); 5216 continue; 5217 } 5218 if (!(val & PCI_COMMAND_MASTER)) { 5219 E1000_ERR(nic, "Can't enable bus-mastering\n"); 5220 continue; 5221 } 5222 5223 /* Are these variables needed? */ 5224 hw->fc = e1000_fc_default; 5225 hw->original_fc = e1000_fc_default; 5226 hw->autoneg_failed = 0; 5227 hw->autoneg = 1; 5228 hw->get_link_status = TRUE; 5229 hw->hw_addr = pci_map_bar(devno, PCI_BASE_ADDRESS_0, 5230 PCI_REGION_MEM); 5231 hw->mac_type = e1000_undefined; 5232 5233 /* MAC and Phy settings */ 5234 if (e1000_sw_init(nic) < 0) { 5235 E1000_ERR(nic, "Software init failed\n"); 5236 continue; 5237 } 5238 if (e1000_check_phy_reset_block(hw)) 5239 E1000_ERR(nic, "PHY Reset is blocked!\n"); 5240 5241 /* Basic init was OK, reset the hardware and allow SPI access */ 5242 e1000_reset_hw(hw); 5243 list_add_tail(&hw->list_node, &e1000_hw_list); 5244 5245 /* Validate the EEPROM and get chipset information */ 5246 #if !(defined(CONFIG_AP1000) || defined(CONFIG_MVBC_1G)) 5247 if (e1000_init_eeprom_params(hw)) { 5248 E1000_ERR(nic, "EEPROM is invalid!\n"); 5249 continue; 5250 } 5251 if (e1000_validate_eeprom_checksum(hw)) 5252 continue; 5253 #endif 5254 e1000_read_mac_addr(nic); 5255 e1000_get_bus_type(hw); 5256 5257 printf("e1000: %02x:%02x:%02x:%02x:%02x:%02x\n ", 5258 nic->enetaddr[0], nic->enetaddr[1], nic->enetaddr[2], 5259 nic->enetaddr[3], nic->enetaddr[4], nic->enetaddr[5]); 5260 5261 /* Set up the function pointers and register the device */ 5262 nic->init = e1000_init; 5263 nic->recv = e1000_poll; 5264 nic->send = e1000_transmit; 5265 nic->halt = e1000_disable; 5266 eth_register(nic); 5267 } 5268 5269 return i; 5270 } 5271 5272 struct e1000_hw *e1000_find_card(unsigned int cardnum) 5273 { 5274 struct e1000_hw *hw; 5275 5276 list_for_each_entry(hw, &e1000_hw_list, list_node) 5277 if (hw->cardnum == cardnum) 5278 return hw; 5279 5280 return NULL; 5281 } 5282 5283 #ifdef CONFIG_CMD_E1000 5284 static int do_e1000(cmd_tbl_t *cmdtp, int flag, 5285 int argc, char * const argv[]) 5286 { 5287 struct e1000_hw *hw; 5288 5289 if (argc < 3) { 5290 cmd_usage(cmdtp); 5291 return 1; 5292 } 5293 5294 /* Make sure we can find the requested e1000 card */ 5295 hw = e1000_find_card(simple_strtoul(argv[1], NULL, 10)); 5296 if (!hw) { 5297 printf("e1000: ERROR: No such device: e1000#%s\n", argv[1]); 5298 return 1; 5299 } 5300 5301 if (!strcmp(argv[2], "print-mac-address")) { 5302 unsigned char *mac = hw->nic->enetaddr; 5303 printf("%02x:%02x:%02x:%02x:%02x:%02x\n", 5304 mac[0], mac[1], mac[2], mac[3], mac[4], mac[5]); 5305 return 0; 5306 } 5307 5308 #ifdef CONFIG_E1000_SPI 5309 /* Handle the "SPI" subcommand */ 5310 if (!strcmp(argv[2], "spi")) 5311 return do_e1000_spi(cmdtp, hw, argc - 3, argv + 3); 5312 #endif 5313 5314 cmd_usage(cmdtp); 5315 return 1; 5316 } 5317 5318 U_BOOT_CMD( 5319 e1000, 7, 0, do_e1000, 5320 "Intel e1000 controller management", 5321 /* */"<card#> print-mac-address\n" 5322 #ifdef CONFIG_E1000_SPI 5323 "e1000 <card#> spi show [<offset> [<length>]]\n" 5324 "e1000 <card#> spi dump <addr> <offset> <length>\n" 5325 "e1000 <card#> spi program <addr> <offset> <length>\n" 5326 "e1000 <card#> spi checksum [update]\n" 5327 #endif 5328 " - Manage the Intel E1000 PCI device" 5329 ); 5330 #endif /* not CONFIG_CMD_E1000 */ 5331