1 /* 2 dm9000.c: Version 1.2 12/15/2003 3 4 A Davicom DM9000 ISA NIC fast Ethernet driver for Linux. 5 Copyright (C) 1997 Sten Wang 6 7 This program is free software; you can redistribute it and/or 8 modify it under the terms of the GNU General Public License 9 as published by the Free Software Foundation; either version 2 10 of the License, or (at your option) any later version. 11 12 This program is distributed in the hope that it will be useful, 13 but WITHOUT ANY WARRANTY; without even the implied warranty of 14 MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 15 GNU General Public License for more details. 16 17 (C)Copyright 1997-1998 DAVICOM Semiconductor,Inc. All Rights Reserved. 18 19 V0.11 06/20/2001 REG_0A bit3=1, default enable BP with DA match 20 06/22/2001 Support DM9801 progrmming 21 E3: R25 = ((R24 + NF) & 0x00ff) | 0xf000 22 E4: R25 = ((R24 + NF) & 0x00ff) | 0xc200 23 R17 = (R17 & 0xfff0) | NF + 3 24 E5: R25 = ((R24 + NF - 3) & 0x00ff) | 0xc200 25 R17 = (R17 & 0xfff0) | NF 26 27 v1.00 modify by simon 2001.9.5 28 change for kernel 2.4.x 29 30 v1.1 11/09/2001 fix force mode bug 31 32 v1.2 03/18/2003 Weilun Huang <weilun_huang@davicom.com.tw>: 33 Fixed phy reset. 34 Added tx/rx 32 bit mode. 35 Cleaned up for kernel merge. 36 37 -------------------------------------- 38 39 12/15/2003 Initial port to u-boot by 40 Sascha Hauer <saschahauer@web.de> 41 42 06/03/2008 Remy Bohmer <linux@bohmer.net> 43 - Fixed the driver to work with DM9000A. 44 (check on ISR receive status bit before reading the 45 FIFO as described in DM9000 programming guide and 46 application notes) 47 - Added autodetect of databus width. 48 - Made debug code compile again. 49 - Adapt eth_send such that it matches the DM9000* 50 application notes. Needed to make it work properly 51 for DM9000A. 52 - Adapted reset procedure to match DM9000 application 53 notes (i.e. double reset) 54 - some minor code cleanups 55 These changes are tested with DM9000{A,EP,E} together 56 with a 200MHz Atmel AT91SAM9261 core 57 58 TODO: external MII is not functional, only internal at the moment. 59 */ 60 61 #include <common.h> 62 #include <command.h> 63 #include <net.h> 64 #include <asm/io.h> 65 #include <dm9000.h> 66 67 #include "dm9000x.h" 68 69 /* Board/System/Debug information/definition ---------------- */ 70 71 /* #define CONFIG_DM9000_DEBUG */ 72 73 #ifdef CONFIG_DM9000_DEBUG 74 #define DM9000_DBG(fmt,args...) printf(fmt, ##args) 75 #define DM9000_DMP_PACKET(func,packet,length) \ 76 do { \ 77 int i; \ 78 printf(func ": length: %d\n", length); \ 79 for (i = 0; i < length; i++) { \ 80 if (i % 8 == 0) \ 81 printf("\n%s: %02x: ", func, i); \ 82 printf("%02x ", ((unsigned char *) packet)[i]); \ 83 } printf("\n"); \ 84 } while(0) 85 #else 86 #define DM9000_DBG(fmt,args...) 87 #define DM9000_DMP_PACKET(func,packet,length) 88 #endif 89 90 /* Structure/enum declaration ------------------------------- */ 91 typedef struct board_info { 92 u32 runt_length_counter; /* counter: RX length < 64byte */ 93 u32 long_length_counter; /* counter: RX length > 1514byte */ 94 u32 reset_counter; /* counter: RESET */ 95 u32 reset_tx_timeout; /* RESET caused by TX Timeout */ 96 u32 reset_rx_status; /* RESET caused by RX Statsus wrong */ 97 u16 tx_pkt_cnt; 98 u16 queue_start_addr; 99 u16 dbug_cnt; 100 u8 phy_addr; 101 u8 device_wait_reset; /* device state */ 102 unsigned char srom[128]; 103 void (*outblk)(volatile void *data_ptr, int count); 104 void (*inblk)(void *data_ptr, int count); 105 void (*rx_status)(u16 *RxStatus, u16 *RxLen); 106 } board_info_t; 107 static board_info_t dm9000_info; 108 109 /* function declaration ------------------------------------- */ 110 int eth_init(bd_t * bd); 111 int eth_send(volatile void *, int); 112 int eth_rx(void); 113 void eth_halt(void); 114 static int dm9000_probe(void); 115 static u16 phy_read(int); 116 static void phy_write(int, u16); 117 static u8 DM9000_ior(int); 118 static void DM9000_iow(int reg, u8 value); 119 120 /* DM9000 network board routine ---------------------------- */ 121 122 #define DM9000_outb(d,r) ( *(volatile u8 *)r = d ) 123 #define DM9000_outw(d,r) ( *(volatile u16 *)r = d ) 124 #define DM9000_outl(d,r) ( *(volatile u32 *)r = d ) 125 #define DM9000_inb(r) (*(volatile u8 *)r) 126 #define DM9000_inw(r) (*(volatile u16 *)r) 127 #define DM9000_inl(r) (*(volatile u32 *)r) 128 129 #ifdef CONFIG_DM9000_DEBUG 130 static void 131 dump_regs(void) 132 { 133 DM9000_DBG("\n"); 134 DM9000_DBG("NCR (0x00): %02x\n", DM9000_ior(0)); 135 DM9000_DBG("NSR (0x01): %02x\n", DM9000_ior(1)); 136 DM9000_DBG("TCR (0x02): %02x\n", DM9000_ior(2)); 137 DM9000_DBG("TSRI (0x03): %02x\n", DM9000_ior(3)); 138 DM9000_DBG("TSRII (0x04): %02x\n", DM9000_ior(4)); 139 DM9000_DBG("RCR (0x05): %02x\n", DM9000_ior(5)); 140 DM9000_DBG("RSR (0x06): %02x\n", DM9000_ior(6)); 141 DM9000_DBG("ISR (0xFE): %02x\n", DM9000_ior(DM9000_ISR)); 142 DM9000_DBG("\n"); 143 } 144 #endif 145 146 static void dm9000_outblk_8bit(volatile void *data_ptr, int count) 147 { 148 int i; 149 for (i = 0; i < count; i++) 150 DM9000_outb((((u8 *) data_ptr)[i] & 0xff), DM9000_DATA); 151 } 152 153 static void dm9000_outblk_16bit(volatile void *data_ptr, int count) 154 { 155 int i; 156 u32 tmplen = (count + 1) / 2; 157 158 for (i = 0; i < tmplen; i++) 159 DM9000_outw(((u16 *) data_ptr)[i], DM9000_DATA); 160 } 161 static void dm9000_outblk_32bit(volatile void *data_ptr, int count) 162 { 163 int i; 164 u32 tmplen = (count + 3) / 4; 165 166 for (i = 0; i < tmplen; i++) 167 DM9000_outl(((u32 *) data_ptr)[i], DM9000_DATA); 168 } 169 170 static void dm9000_inblk_8bit(void *data_ptr, int count) 171 { 172 int i; 173 for (i = 0; i < count; i++) 174 ((u8 *) data_ptr)[i] = DM9000_inb(DM9000_DATA); 175 } 176 177 static void dm9000_inblk_16bit(void *data_ptr, int count) 178 { 179 int i; 180 u32 tmplen = (count + 1) / 2; 181 182 for (i = 0; i < tmplen; i++) 183 ((u16 *) data_ptr)[i] = DM9000_inw(DM9000_DATA); 184 } 185 static void dm9000_inblk_32bit(void *data_ptr, int count) 186 { 187 int i; 188 u32 tmplen = (count + 3) / 4; 189 190 for (i = 0; i < tmplen; i++) 191 ((u32 *) data_ptr)[i] = DM9000_inl(DM9000_DATA); 192 } 193 194 static void dm9000_rx_status_32bit(u16 *RxStatus, u16 *RxLen) 195 { 196 u32 tmpdata; 197 198 DM9000_outb(DM9000_MRCMD, DM9000_IO); 199 200 tmpdata = DM9000_inl(DM9000_DATA); 201 *RxStatus = __le16_to_cpu(tmpdata); 202 *RxLen = __le16_to_cpu(tmpdata >> 16); 203 } 204 205 static void dm9000_rx_status_16bit(u16 *RxStatus, u16 *RxLen) 206 { 207 DM9000_outb(DM9000_MRCMD, DM9000_IO); 208 209 *RxStatus = __le16_to_cpu(DM9000_inw(DM9000_DATA)); 210 *RxLen = __le16_to_cpu(DM9000_inw(DM9000_DATA)); 211 } 212 213 static void dm9000_rx_status_8bit(u16 *RxStatus, u16 *RxLen) 214 { 215 DM9000_outb(DM9000_MRCMD, DM9000_IO); 216 217 *RxStatus = 218 __le16_to_cpu(DM9000_inb(DM9000_DATA) + 219 (DM9000_inb(DM9000_DATA) << 8)); 220 *RxLen = 221 __le16_to_cpu(DM9000_inb(DM9000_DATA) + 222 (DM9000_inb(DM9000_DATA) << 8)); 223 } 224 225 /* 226 Search DM9000 board, allocate space and register it 227 */ 228 int 229 dm9000_probe(void) 230 { 231 u32 id_val; 232 id_val = DM9000_ior(DM9000_VIDL); 233 id_val |= DM9000_ior(DM9000_VIDH) << 8; 234 id_val |= DM9000_ior(DM9000_PIDL) << 16; 235 id_val |= DM9000_ior(DM9000_PIDH) << 24; 236 if (id_val == DM9000_ID) { 237 printf("dm9000 i/o: 0x%x, id: 0x%x \n", CONFIG_DM9000_BASE, 238 id_val); 239 return 0; 240 } else { 241 printf("dm9000 not found at 0x%08x id: 0x%08x\n", 242 CONFIG_DM9000_BASE, id_val); 243 return -1; 244 } 245 } 246 247 /* General Purpose dm9000 reset routine */ 248 static void 249 dm9000_reset(void) 250 { 251 DM9000_DBG("resetting DM9000\n"); 252 253 /* Reset DM9000, 254 see DM9000 Application Notes V1.22 Jun 11, 2004 page 29 */ 255 256 /* DEBUG: Make all GPIO0 outputs, all others inputs */ 257 DM9000_iow(DM9000_GPCR, GPCR_GPIO0_OUT); 258 /* Step 1: Power internal PHY by writing 0 to GPIO0 pin */ 259 DM9000_iow(DM9000_GPR, 0); 260 /* Step 2: Software reset */ 261 DM9000_iow(DM9000_NCR, (NCR_LBK_INT_MAC | NCR_RST)); 262 263 do { 264 DM9000_DBG("resetting the DM9000, 1st reset\n"); 265 udelay(25); /* Wait at least 20 us */ 266 } while (DM9000_ior(DM9000_NCR) & 1); 267 268 DM9000_iow(DM9000_NCR, 0); 269 DM9000_iow(DM9000_NCR, (NCR_LBK_INT_MAC | NCR_RST)); /* Issue a second reset */ 270 271 do { 272 DM9000_DBG("resetting the DM9000, 2nd reset\n"); 273 udelay(25); /* Wait at least 20 us */ 274 } while (DM9000_ior(DM9000_NCR) & 1); 275 276 /* Check whether the ethernet controller is present */ 277 if ((DM9000_ior(DM9000_PIDL) != 0x0) || 278 (DM9000_ior(DM9000_PIDH) != 0x90)) 279 printf("ERROR: resetting DM9000 -> not responding\n"); 280 } 281 282 /* Initilize dm9000 board 283 */ 284 int 285 eth_init(bd_t * bd) 286 { 287 int i, oft, lnk; 288 u8 io_mode; 289 struct board_info *db = &dm9000_info; 290 uchar enetaddr[6]; 291 292 DM9000_DBG("eth_init()\n"); 293 294 /* RESET device */ 295 dm9000_reset(); 296 297 if (dm9000_probe() < 0) 298 return -1; 299 300 /* Auto-detect 8/16/32 bit mode, ISR Bit 6+7 indicate bus width */ 301 io_mode = DM9000_ior(DM9000_ISR) >> 6; 302 303 switch (io_mode) { 304 case 0x0: /* 16-bit mode */ 305 printf("DM9000: running in 16 bit mode\n"); 306 db->outblk = dm9000_outblk_16bit; 307 db->inblk = dm9000_inblk_16bit; 308 db->rx_status = dm9000_rx_status_16bit; 309 break; 310 case 0x01: /* 32-bit mode */ 311 printf("DM9000: running in 32 bit mode\n"); 312 db->outblk = dm9000_outblk_32bit; 313 db->inblk = dm9000_inblk_32bit; 314 db->rx_status = dm9000_rx_status_32bit; 315 break; 316 case 0x02: /* 8 bit mode */ 317 printf("DM9000: running in 8 bit mode\n"); 318 db->outblk = dm9000_outblk_8bit; 319 db->inblk = dm9000_inblk_8bit; 320 db->rx_status = dm9000_rx_status_8bit; 321 break; 322 default: 323 /* Assume 8 bit mode, will probably not work anyway */ 324 printf("DM9000: Undefined IO-mode:0x%x\n", io_mode); 325 db->outblk = dm9000_outblk_8bit; 326 db->inblk = dm9000_inblk_8bit; 327 db->rx_status = dm9000_rx_status_8bit; 328 break; 329 } 330 331 /* Program operating register, only internal phy supported */ 332 DM9000_iow(DM9000_NCR, 0x0); 333 /* TX Polling clear */ 334 DM9000_iow(DM9000_TCR, 0); 335 /* Less 3Kb, 200us */ 336 DM9000_iow(DM9000_BPTR, BPTR_BPHW(3) | BPTR_JPT_600US); 337 /* Flow Control : High/Low Water */ 338 DM9000_iow(DM9000_FCTR, FCTR_HWOT(3) | FCTR_LWOT(8)); 339 /* SH FIXME: This looks strange! Flow Control */ 340 DM9000_iow(DM9000_FCR, 0x0); 341 /* Special Mode */ 342 DM9000_iow(DM9000_SMCR, 0); 343 /* clear TX status */ 344 DM9000_iow(DM9000_NSR, NSR_WAKEST | NSR_TX2END | NSR_TX1END); 345 /* Clear interrupt status */ 346 DM9000_iow(DM9000_ISR, ISR_ROOS | ISR_ROS | ISR_PTS | ISR_PRS); 347 348 /* Set Node address */ 349 if (!eth_getenv_enetaddr("ethaddr", enetaddr)) { 350 #if !defined(CONFIG_DM9000_NO_SROM) 351 for (i = 0; i < 3; i++) 352 dm9000_read_srom_word(i, enetaddr + 2 * i); 353 eth_setenv_enetaddr("ethaddr", enetaddr); 354 #endif 355 } 356 357 printf("MAC: %pM\n", enetaddr); 358 359 /* fill device MAC address registers */ 360 for (i = 0, oft = DM9000_PAR; i < 6; i++, oft++) 361 DM9000_iow(oft, enetaddr[i]); 362 for (i = 0, oft = 0x16; i < 8; i++, oft++) 363 DM9000_iow(oft, 0xff); 364 365 /* read back mac, just to be sure */ 366 for (i = 0, oft = 0x10; i < 6; i++, oft++) 367 DM9000_DBG("%02x:", DM9000_ior(oft)); 368 DM9000_DBG("\n"); 369 370 /* Activate DM9000 */ 371 /* RX enable */ 372 DM9000_iow(DM9000_RCR, RCR_DIS_LONG | RCR_DIS_CRC | RCR_RXEN); 373 /* Enable TX/RX interrupt mask */ 374 DM9000_iow(DM9000_IMR, IMR_PAR); 375 376 i = 0; 377 while (!(phy_read(1) & 0x20)) { /* autonegation complete bit */ 378 udelay(1000); 379 i++; 380 if (i == 10000) { 381 printf("could not establish link\n"); 382 return 0; 383 } 384 } 385 386 /* see what we've got */ 387 lnk = phy_read(17) >> 12; 388 printf("operating at "); 389 switch (lnk) { 390 case 1: 391 printf("10M half duplex "); 392 break; 393 case 2: 394 printf("10M full duplex "); 395 break; 396 case 4: 397 printf("100M half duplex "); 398 break; 399 case 8: 400 printf("100M full duplex "); 401 break; 402 default: 403 printf("unknown: %d ", lnk); 404 break; 405 } 406 printf("mode\n"); 407 return 0; 408 } 409 410 /* 411 Hardware start transmission. 412 Send a packet to media from the upper layer. 413 */ 414 int 415 eth_send(volatile void *packet, int length) 416 { 417 int tmo; 418 struct board_info *db = &dm9000_info; 419 420 DM9000_DMP_PACKET("eth_send", packet, length); 421 422 DM9000_iow(DM9000_ISR, IMR_PTM); /* Clear Tx bit in ISR */ 423 424 /* Move data to DM9000 TX RAM */ 425 DM9000_outb(DM9000_MWCMD, DM9000_IO); /* Prepare for TX-data */ 426 427 /* push the data to the TX-fifo */ 428 (db->outblk)(packet, length); 429 430 /* Set TX length to DM9000 */ 431 DM9000_iow(DM9000_TXPLL, length & 0xff); 432 DM9000_iow(DM9000_TXPLH, (length >> 8) & 0xff); 433 434 /* Issue TX polling command */ 435 DM9000_iow(DM9000_TCR, TCR_TXREQ); /* Cleared after TX complete */ 436 437 /* wait for end of transmission */ 438 tmo = get_timer(0) + 5 * CONFIG_SYS_HZ; 439 while ( !(DM9000_ior(DM9000_NSR) & (NSR_TX1END | NSR_TX2END)) || 440 !(DM9000_ior(DM9000_ISR) & IMR_PTM) ) { 441 if (get_timer(0) >= tmo) { 442 printf("transmission timeout\n"); 443 break; 444 } 445 } 446 DM9000_iow(DM9000_ISR, IMR_PTM); /* Clear Tx bit in ISR */ 447 448 DM9000_DBG("transmit done\n\n"); 449 return 0; 450 } 451 452 /* 453 Stop the interface. 454 The interface is stopped when it is brought. 455 */ 456 void 457 eth_halt(void) 458 { 459 DM9000_DBG("eth_halt\n"); 460 461 /* RESET devie */ 462 phy_write(0, 0x8000); /* PHY RESET */ 463 DM9000_iow(DM9000_GPR, 0x01); /* Power-Down PHY */ 464 DM9000_iow(DM9000_IMR, 0x80); /* Disable all interrupt */ 465 DM9000_iow(DM9000_RCR, 0x00); /* Disable RX */ 466 } 467 468 /* 469 Received a packet and pass to upper layer 470 */ 471 int 472 eth_rx(void) 473 { 474 u8 rxbyte, *rdptr = (u8 *) NetRxPackets[0]; 475 u16 RxStatus, RxLen = 0; 476 struct board_info *db = &dm9000_info; 477 478 /* Check packet ready or not, we must check 479 the ISR status first for DM9000A */ 480 if (!(DM9000_ior(DM9000_ISR) & 0x01)) /* Rx-ISR bit must be set. */ 481 return 0; 482 483 DM9000_iow(DM9000_ISR, 0x01); /* clear PR status latched in bit 0 */ 484 485 /* There is _at least_ 1 package in the fifo, read them all */ 486 for (;;) { 487 DM9000_ior(DM9000_MRCMDX); /* Dummy read */ 488 489 /* Get most updated data, 490 only look at bits 0:1, See application notes DM9000 */ 491 rxbyte = DM9000_inb(DM9000_DATA) & 0x03; 492 493 /* Status check: this byte must be 0 or 1 */ 494 if (rxbyte > DM9000_PKT_RDY) { 495 DM9000_iow(DM9000_RCR, 0x00); /* Stop Device */ 496 DM9000_iow(DM9000_ISR, 0x80); /* Stop INT request */ 497 printf("DM9000 error: status check fail: 0x%x\n", 498 rxbyte); 499 return 0; 500 } 501 502 if (rxbyte != DM9000_PKT_RDY) 503 return 0; /* No packet received, ignore */ 504 505 DM9000_DBG("receiving packet\n"); 506 507 /* A packet ready now & Get status/length */ 508 (db->rx_status)(&RxStatus, &RxLen); 509 510 DM9000_DBG("rx status: 0x%04x rx len: %d\n", RxStatus, RxLen); 511 512 /* Move data from DM9000 */ 513 /* Read received packet from RX SRAM */ 514 (db->inblk)(rdptr, RxLen); 515 516 if ((RxStatus & 0xbf00) || (RxLen < 0x40) 517 || (RxLen > DM9000_PKT_MAX)) { 518 if (RxStatus & 0x100) { 519 printf("rx fifo error\n"); 520 } 521 if (RxStatus & 0x200) { 522 printf("rx crc error\n"); 523 } 524 if (RxStatus & 0x8000) { 525 printf("rx length error\n"); 526 } 527 if (RxLen > DM9000_PKT_MAX) { 528 printf("rx length too big\n"); 529 dm9000_reset(); 530 } 531 } else { 532 DM9000_DMP_PACKET("eth_rx", rdptr, RxLen); 533 534 DM9000_DBG("passing packet to upper layer\n"); 535 NetReceive(NetRxPackets[0], RxLen); 536 } 537 } 538 return 0; 539 } 540 541 /* 542 Read a word data from SROM 543 */ 544 #if !defined(CONFIG_DM9000_NO_SROM) 545 void dm9000_read_srom_word(int offset, u8 *to) 546 { 547 DM9000_iow(DM9000_EPAR, offset); 548 DM9000_iow(DM9000_EPCR, 0x4); 549 udelay(8000); 550 DM9000_iow(DM9000_EPCR, 0x0); 551 to[0] = DM9000_ior(DM9000_EPDRL); 552 to[1] = DM9000_ior(DM9000_EPDRH); 553 } 554 555 void dm9000_write_srom_word(int offset, u16 val) 556 { 557 DM9000_iow(DM9000_EPAR, offset); 558 DM9000_iow(DM9000_EPDRH, ((val >> 8) & 0xff)); 559 DM9000_iow(DM9000_EPDRL, (val & 0xff)); 560 DM9000_iow(DM9000_EPCR, 0x12); 561 udelay(8000); 562 DM9000_iow(DM9000_EPCR, 0); 563 } 564 #endif 565 566 /* 567 Read a byte from I/O port 568 */ 569 static u8 570 DM9000_ior(int reg) 571 { 572 DM9000_outb(reg, DM9000_IO); 573 return DM9000_inb(DM9000_DATA); 574 } 575 576 /* 577 Write a byte to I/O port 578 */ 579 static void 580 DM9000_iow(int reg, u8 value) 581 { 582 DM9000_outb(reg, DM9000_IO); 583 DM9000_outb(value, DM9000_DATA); 584 } 585 586 /* 587 Read a word from phyxcer 588 */ 589 static u16 590 phy_read(int reg) 591 { 592 u16 val; 593 594 /* Fill the phyxcer register into REG_0C */ 595 DM9000_iow(DM9000_EPAR, DM9000_PHY | reg); 596 DM9000_iow(DM9000_EPCR, 0xc); /* Issue phyxcer read command */ 597 udelay(100); /* Wait read complete */ 598 DM9000_iow(DM9000_EPCR, 0x0); /* Clear phyxcer read command */ 599 val = (DM9000_ior(DM9000_EPDRH) << 8) | DM9000_ior(DM9000_EPDRL); 600 601 /* The read data keeps on REG_0D & REG_0E */ 602 DM9000_DBG("phy_read(0x%x): 0x%x\n", reg, val); 603 return val; 604 } 605 606 /* 607 Write a word to phyxcer 608 */ 609 static void 610 phy_write(int reg, u16 value) 611 { 612 613 /* Fill the phyxcer register into REG_0C */ 614 DM9000_iow(DM9000_EPAR, DM9000_PHY | reg); 615 616 /* Fill the written data into REG_0D & REG_0E */ 617 DM9000_iow(DM9000_EPDRL, (value & 0xff)); 618 DM9000_iow(DM9000_EPDRH, ((value >> 8) & 0xff)); 619 DM9000_iow(DM9000_EPCR, 0xa); /* Issue phyxcer write command */ 620 udelay(500); /* Wait write complete */ 621 DM9000_iow(DM9000_EPCR, 0x0); /* Clear phyxcer write command */ 622 DM9000_DBG("phy_write(reg:0x%x, value:0x%x)\n", reg, value); 623 } 624