1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * (C) Copyright 2010 4 * Vipin Kumar, ST Micoelectronics, vipin.kumar@st.com. 5 */ 6 7 /* 8 * Designware ethernet IP driver for U-Boot 9 */ 10 11 #include <common.h> 12 #include <clk.h> 13 #include <dm.h> 14 #include <errno.h> 15 #include <miiphy.h> 16 #include <malloc.h> 17 #include <pci.h> 18 #include <reset.h> 19 #include <linux/compiler.h> 20 #include <linux/err.h> 21 #include <linux/kernel.h> 22 #include <asm/io.h> 23 #include <power/regulator.h> 24 #include "designware.h" 25 26 static int dw_mdio_read(struct mii_dev *bus, int addr, int devad, int reg) 27 { 28 #ifdef CONFIG_DM_ETH 29 struct dw_eth_dev *priv = dev_get_priv((struct udevice *)bus->priv); 30 struct eth_mac_regs *mac_p = priv->mac_regs_p; 31 #else 32 struct eth_mac_regs *mac_p = bus->priv; 33 #endif 34 ulong start; 35 u16 miiaddr; 36 int timeout = CONFIG_MDIO_TIMEOUT; 37 38 miiaddr = ((addr << MIIADDRSHIFT) & MII_ADDRMSK) | 39 ((reg << MIIREGSHIFT) & MII_REGMSK); 40 41 writel(miiaddr | MII_CLKRANGE_150_250M | MII_BUSY, &mac_p->miiaddr); 42 43 start = get_timer(0); 44 while (get_timer(start) < timeout) { 45 if (!(readl(&mac_p->miiaddr) & MII_BUSY)) 46 return readl(&mac_p->miidata); 47 udelay(10); 48 }; 49 50 return -ETIMEDOUT; 51 } 52 53 static int dw_mdio_write(struct mii_dev *bus, int addr, int devad, int reg, 54 u16 val) 55 { 56 #ifdef CONFIG_DM_ETH 57 struct dw_eth_dev *priv = dev_get_priv((struct udevice *)bus->priv); 58 struct eth_mac_regs *mac_p = priv->mac_regs_p; 59 #else 60 struct eth_mac_regs *mac_p = bus->priv; 61 #endif 62 ulong start; 63 u16 miiaddr; 64 int ret = -ETIMEDOUT, timeout = CONFIG_MDIO_TIMEOUT; 65 66 writel(val, &mac_p->miidata); 67 miiaddr = ((addr << MIIADDRSHIFT) & MII_ADDRMSK) | 68 ((reg << MIIREGSHIFT) & MII_REGMSK) | MII_WRITE; 69 70 writel(miiaddr | MII_CLKRANGE_150_250M | MII_BUSY, &mac_p->miiaddr); 71 72 start = get_timer(0); 73 while (get_timer(start) < timeout) { 74 if (!(readl(&mac_p->miiaddr) & MII_BUSY)) { 75 ret = 0; 76 break; 77 } 78 udelay(10); 79 }; 80 81 return ret; 82 } 83 84 #if defined(CONFIG_DM_ETH) && defined(CONFIG_DM_GPIO) 85 static int dw_mdio_reset(struct mii_dev *bus) 86 { 87 struct udevice *dev = bus->priv; 88 struct dw_eth_dev *priv = dev_get_priv(dev); 89 struct dw_eth_pdata *pdata = dev_get_platdata(dev); 90 int ret; 91 92 if (!dm_gpio_is_valid(&priv->reset_gpio)) 93 return 0; 94 95 /* reset the phy */ 96 ret = dm_gpio_set_value(&priv->reset_gpio, 0); 97 if (ret) 98 return ret; 99 100 udelay(pdata->reset_delays[0]); 101 102 ret = dm_gpio_set_value(&priv->reset_gpio, 1); 103 if (ret) 104 return ret; 105 106 udelay(pdata->reset_delays[1]); 107 108 ret = dm_gpio_set_value(&priv->reset_gpio, 0); 109 if (ret) 110 return ret; 111 112 udelay(pdata->reset_delays[2]); 113 114 return 0; 115 } 116 #endif 117 118 static int dw_mdio_init(const char *name, void *priv) 119 { 120 struct mii_dev *bus = mdio_alloc(); 121 122 if (!bus) { 123 printf("Failed to allocate MDIO bus\n"); 124 return -ENOMEM; 125 } 126 127 bus->read = dw_mdio_read; 128 bus->write = dw_mdio_write; 129 snprintf(bus->name, sizeof(bus->name), "%s", name); 130 #if defined(CONFIG_DM_ETH) && defined(CONFIG_DM_GPIO) 131 bus->reset = dw_mdio_reset; 132 #endif 133 134 bus->priv = priv; 135 136 return mdio_register(bus); 137 } 138 139 static void tx_descs_init(struct dw_eth_dev *priv) 140 { 141 struct eth_dma_regs *dma_p = priv->dma_regs_p; 142 struct dmamacdescr *desc_table_p = &priv->tx_mac_descrtable[0]; 143 char *txbuffs = &priv->txbuffs[0]; 144 struct dmamacdescr *desc_p; 145 u32 idx; 146 147 for (idx = 0; idx < CONFIG_TX_DESCR_NUM; idx++) { 148 desc_p = &desc_table_p[idx]; 149 desc_p->dmamac_addr = (ulong)&txbuffs[idx * CONFIG_ETH_BUFSIZE]; 150 desc_p->dmamac_next = (ulong)&desc_table_p[idx + 1]; 151 152 #if defined(CONFIG_DW_ALTDESCRIPTOR) 153 desc_p->txrx_status &= ~(DESC_TXSTS_TXINT | DESC_TXSTS_TXLAST | 154 DESC_TXSTS_TXFIRST | DESC_TXSTS_TXCRCDIS | 155 DESC_TXSTS_TXCHECKINSCTRL | 156 DESC_TXSTS_TXRINGEND | DESC_TXSTS_TXPADDIS); 157 158 desc_p->txrx_status |= DESC_TXSTS_TXCHAIN; 159 desc_p->dmamac_cntl = 0; 160 desc_p->txrx_status &= ~(DESC_TXSTS_MSK | DESC_TXSTS_OWNBYDMA); 161 #else 162 desc_p->dmamac_cntl = DESC_TXCTRL_TXCHAIN; 163 desc_p->txrx_status = 0; 164 #endif 165 } 166 167 /* Correcting the last pointer of the chain */ 168 desc_p->dmamac_next = (ulong)&desc_table_p[0]; 169 170 /* Flush all Tx buffer descriptors at once */ 171 flush_dcache_range((ulong)priv->tx_mac_descrtable, 172 (ulong)priv->tx_mac_descrtable + 173 sizeof(priv->tx_mac_descrtable)); 174 175 writel((ulong)&desc_table_p[0], &dma_p->txdesclistaddr); 176 priv->tx_currdescnum = 0; 177 } 178 179 static void rx_descs_init(struct dw_eth_dev *priv) 180 { 181 struct eth_dma_regs *dma_p = priv->dma_regs_p; 182 struct dmamacdescr *desc_table_p = &priv->rx_mac_descrtable[0]; 183 char *rxbuffs = &priv->rxbuffs[0]; 184 struct dmamacdescr *desc_p; 185 u32 idx; 186 187 /* Before passing buffers to GMAC we need to make sure zeros 188 * written there right after "priv" structure allocation were 189 * flushed into RAM. 190 * Otherwise there's a chance to get some of them flushed in RAM when 191 * GMAC is already pushing data to RAM via DMA. This way incoming from 192 * GMAC data will be corrupted. */ 193 flush_dcache_range((ulong)rxbuffs, (ulong)rxbuffs + RX_TOTAL_BUFSIZE); 194 195 for (idx = 0; idx < CONFIG_RX_DESCR_NUM; idx++) { 196 desc_p = &desc_table_p[idx]; 197 desc_p->dmamac_addr = (ulong)&rxbuffs[idx * CONFIG_ETH_BUFSIZE]; 198 desc_p->dmamac_next = (ulong)&desc_table_p[idx + 1]; 199 200 desc_p->dmamac_cntl = 201 (MAC_MAX_FRAME_SZ & DESC_RXCTRL_SIZE1MASK) | 202 DESC_RXCTRL_RXCHAIN; 203 204 desc_p->txrx_status = DESC_RXSTS_OWNBYDMA; 205 } 206 207 /* Correcting the last pointer of the chain */ 208 desc_p->dmamac_next = (ulong)&desc_table_p[0]; 209 210 /* Flush all Rx buffer descriptors at once */ 211 flush_dcache_range((ulong)priv->rx_mac_descrtable, 212 (ulong)priv->rx_mac_descrtable + 213 sizeof(priv->rx_mac_descrtable)); 214 215 writel((ulong)&desc_table_p[0], &dma_p->rxdesclistaddr); 216 priv->rx_currdescnum = 0; 217 } 218 219 static int _dw_write_hwaddr(struct dw_eth_dev *priv, u8 *mac_id) 220 { 221 struct eth_mac_regs *mac_p = priv->mac_regs_p; 222 u32 macid_lo, macid_hi; 223 224 macid_lo = mac_id[0] + (mac_id[1] << 8) + (mac_id[2] << 16) + 225 (mac_id[3] << 24); 226 macid_hi = mac_id[4] + (mac_id[5] << 8); 227 228 writel(macid_hi, &mac_p->macaddr0hi); 229 writel(macid_lo, &mac_p->macaddr0lo); 230 231 return 0; 232 } 233 234 static int dw_adjust_link(struct dw_eth_dev *priv, struct eth_mac_regs *mac_p, 235 struct phy_device *phydev) 236 { 237 u32 conf = readl(&mac_p->conf) | FRAMEBURSTENABLE | DISABLERXOWN; 238 239 if (!phydev->link) { 240 printf("%s: No link.\n", phydev->dev->name); 241 return 0; 242 } 243 244 if (phydev->speed != 1000) 245 conf |= MII_PORTSELECT; 246 else 247 conf &= ~MII_PORTSELECT; 248 249 if (phydev->speed == 100) 250 conf |= FES_100; 251 252 if (phydev->duplex) 253 conf |= FULLDPLXMODE; 254 255 writel(conf, &mac_p->conf); 256 257 printf("Speed: %d, %s duplex%s\n", phydev->speed, 258 (phydev->duplex) ? "full" : "half", 259 (phydev->port == PORT_FIBRE) ? ", fiber mode" : ""); 260 261 return 0; 262 } 263 264 static void _dw_eth_halt(struct dw_eth_dev *priv) 265 { 266 struct eth_mac_regs *mac_p = priv->mac_regs_p; 267 struct eth_dma_regs *dma_p = priv->dma_regs_p; 268 269 writel(readl(&mac_p->conf) & ~(RXENABLE | TXENABLE), &mac_p->conf); 270 writel(readl(&dma_p->opmode) & ~(RXSTART | TXSTART), &dma_p->opmode); 271 272 phy_shutdown(priv->phydev); 273 } 274 275 int designware_eth_init(struct dw_eth_dev *priv, u8 *enetaddr) 276 { 277 struct eth_mac_regs *mac_p = priv->mac_regs_p; 278 struct eth_dma_regs *dma_p = priv->dma_regs_p; 279 unsigned int start; 280 int ret; 281 282 writel(readl(&dma_p->busmode) | DMAMAC_SRST, &dma_p->busmode); 283 284 /* 285 * When a MII PHY is used, we must set the PS bit for the DMA 286 * reset to succeed. 287 */ 288 if (priv->phydev->interface == PHY_INTERFACE_MODE_MII) 289 writel(readl(&mac_p->conf) | MII_PORTSELECT, &mac_p->conf); 290 else 291 writel(readl(&mac_p->conf) & ~MII_PORTSELECT, &mac_p->conf); 292 293 start = get_timer(0); 294 while (readl(&dma_p->busmode) & DMAMAC_SRST) { 295 if (get_timer(start) >= CONFIG_MACRESET_TIMEOUT) { 296 printf("DMA reset timeout\n"); 297 return -ETIMEDOUT; 298 } 299 300 mdelay(100); 301 }; 302 303 /* 304 * Soft reset above clears HW address registers. 305 * So we have to set it here once again. 306 */ 307 _dw_write_hwaddr(priv, enetaddr); 308 309 rx_descs_init(priv); 310 tx_descs_init(priv); 311 312 writel(FIXEDBURST | PRIORXTX_41 | DMA_PBL, &dma_p->busmode); 313 314 #ifndef CONFIG_DW_MAC_FORCE_THRESHOLD_MODE 315 writel(readl(&dma_p->opmode) | FLUSHTXFIFO | STOREFORWARD, 316 &dma_p->opmode); 317 #else 318 writel(readl(&dma_p->opmode) | FLUSHTXFIFO, 319 &dma_p->opmode); 320 #endif 321 322 writel(readl(&dma_p->opmode) | RXSTART | TXSTART, &dma_p->opmode); 323 324 #ifdef CONFIG_DW_AXI_BURST_LEN 325 writel((CONFIG_DW_AXI_BURST_LEN & 0x1FF >> 1), &dma_p->axibus); 326 #endif 327 328 /* Start up the PHY */ 329 ret = phy_startup(priv->phydev); 330 if (ret) { 331 printf("Could not initialize PHY %s\n", 332 priv->phydev->dev->name); 333 return ret; 334 } 335 336 ret = dw_adjust_link(priv, mac_p, priv->phydev); 337 if (ret) 338 return ret; 339 340 return 0; 341 } 342 343 int designware_eth_enable(struct dw_eth_dev *priv) 344 { 345 struct eth_mac_regs *mac_p = priv->mac_regs_p; 346 347 if (!priv->phydev->link) 348 return -EIO; 349 350 writel(readl(&mac_p->conf) | RXENABLE | TXENABLE, &mac_p->conf); 351 352 return 0; 353 } 354 355 #define ETH_ZLEN 60 356 357 static int _dw_eth_send(struct dw_eth_dev *priv, void *packet, int length) 358 { 359 struct eth_dma_regs *dma_p = priv->dma_regs_p; 360 u32 desc_num = priv->tx_currdescnum; 361 struct dmamacdescr *desc_p = &priv->tx_mac_descrtable[desc_num]; 362 ulong desc_start = (ulong)desc_p; 363 ulong desc_end = desc_start + 364 roundup(sizeof(*desc_p), ARCH_DMA_MINALIGN); 365 ulong data_start = desc_p->dmamac_addr; 366 ulong data_end = data_start + roundup(length, ARCH_DMA_MINALIGN); 367 /* 368 * Strictly we only need to invalidate the "txrx_status" field 369 * for the following check, but on some platforms we cannot 370 * invalidate only 4 bytes, so we flush the entire descriptor, 371 * which is 16 bytes in total. This is safe because the 372 * individual descriptors in the array are each aligned to 373 * ARCH_DMA_MINALIGN and padded appropriately. 374 */ 375 invalidate_dcache_range(desc_start, desc_end); 376 377 /* Check if the descriptor is owned by CPU */ 378 if (desc_p->txrx_status & DESC_TXSTS_OWNBYDMA) { 379 printf("CPU not owner of tx frame\n"); 380 return -EPERM; 381 } 382 383 length = max(length, ETH_ZLEN); 384 385 memcpy((void *)data_start, packet, length); 386 387 /* Flush data to be sent */ 388 flush_dcache_range(data_start, data_end); 389 390 #if defined(CONFIG_DW_ALTDESCRIPTOR) 391 desc_p->txrx_status |= DESC_TXSTS_TXFIRST | DESC_TXSTS_TXLAST; 392 desc_p->dmamac_cntl |= (length << DESC_TXCTRL_SIZE1SHFT) & 393 DESC_TXCTRL_SIZE1MASK; 394 395 desc_p->txrx_status &= ~(DESC_TXSTS_MSK); 396 desc_p->txrx_status |= DESC_TXSTS_OWNBYDMA; 397 #else 398 desc_p->dmamac_cntl |= ((length << DESC_TXCTRL_SIZE1SHFT) & 399 DESC_TXCTRL_SIZE1MASK) | DESC_TXCTRL_TXLAST | 400 DESC_TXCTRL_TXFIRST; 401 402 desc_p->txrx_status = DESC_TXSTS_OWNBYDMA; 403 #endif 404 405 /* Flush modified buffer descriptor */ 406 flush_dcache_range(desc_start, desc_end); 407 408 /* Test the wrap-around condition. */ 409 if (++desc_num >= CONFIG_TX_DESCR_NUM) 410 desc_num = 0; 411 412 priv->tx_currdescnum = desc_num; 413 414 /* Start the transmission */ 415 writel(POLL_DATA, &dma_p->txpolldemand); 416 417 return 0; 418 } 419 420 static int _dw_eth_recv(struct dw_eth_dev *priv, uchar **packetp) 421 { 422 u32 status, desc_num = priv->rx_currdescnum; 423 struct dmamacdescr *desc_p = &priv->rx_mac_descrtable[desc_num]; 424 int length = -EAGAIN; 425 ulong desc_start = (ulong)desc_p; 426 ulong desc_end = desc_start + 427 roundup(sizeof(*desc_p), ARCH_DMA_MINALIGN); 428 ulong data_start = desc_p->dmamac_addr; 429 ulong data_end; 430 431 /* Invalidate entire buffer descriptor */ 432 invalidate_dcache_range(desc_start, desc_end); 433 434 status = desc_p->txrx_status; 435 436 /* Check if the owner is the CPU */ 437 if (!(status & DESC_RXSTS_OWNBYDMA)) { 438 439 length = (status & DESC_RXSTS_FRMLENMSK) >> 440 DESC_RXSTS_FRMLENSHFT; 441 442 /* Invalidate received data */ 443 data_end = data_start + roundup(length, ARCH_DMA_MINALIGN); 444 invalidate_dcache_range(data_start, data_end); 445 *packetp = (uchar *)(ulong)desc_p->dmamac_addr; 446 } 447 448 return length; 449 } 450 451 static int _dw_free_pkt(struct dw_eth_dev *priv) 452 { 453 u32 desc_num = priv->rx_currdescnum; 454 struct dmamacdescr *desc_p = &priv->rx_mac_descrtable[desc_num]; 455 ulong desc_start = (ulong)desc_p; 456 ulong desc_end = desc_start + 457 roundup(sizeof(*desc_p), ARCH_DMA_MINALIGN); 458 459 /* 460 * Make the current descriptor valid again and go to 461 * the next one 462 */ 463 desc_p->txrx_status |= DESC_RXSTS_OWNBYDMA; 464 465 /* Flush only status field - others weren't changed */ 466 flush_dcache_range(desc_start, desc_end); 467 468 /* Test the wrap-around condition. */ 469 if (++desc_num >= CONFIG_RX_DESCR_NUM) 470 desc_num = 0; 471 priv->rx_currdescnum = desc_num; 472 473 return 0; 474 } 475 476 static int dw_phy_init(struct dw_eth_dev *priv, void *dev) 477 { 478 struct phy_device *phydev; 479 int mask = 0xffffffff, ret; 480 481 #ifdef CONFIG_PHY_ADDR 482 mask = 1 << CONFIG_PHY_ADDR; 483 #endif 484 485 phydev = phy_find_by_mask(priv->bus, mask, priv->interface); 486 if (!phydev) 487 return -ENODEV; 488 489 phy_connect_dev(phydev, dev); 490 491 phydev->supported &= PHY_GBIT_FEATURES; 492 if (priv->max_speed) { 493 ret = phy_set_supported(phydev, priv->max_speed); 494 if (ret) 495 return ret; 496 } 497 phydev->advertising = phydev->supported; 498 499 priv->phydev = phydev; 500 phy_config(phydev); 501 502 return 0; 503 } 504 505 #ifndef CONFIG_DM_ETH 506 static int dw_eth_init(struct eth_device *dev, bd_t *bis) 507 { 508 int ret; 509 510 ret = designware_eth_init(dev->priv, dev->enetaddr); 511 if (!ret) 512 ret = designware_eth_enable(dev->priv); 513 514 return ret; 515 } 516 517 static int dw_eth_send(struct eth_device *dev, void *packet, int length) 518 { 519 return _dw_eth_send(dev->priv, packet, length); 520 } 521 522 static int dw_eth_recv(struct eth_device *dev) 523 { 524 uchar *packet; 525 int length; 526 527 length = _dw_eth_recv(dev->priv, &packet); 528 if (length == -EAGAIN) 529 return 0; 530 net_process_received_packet(packet, length); 531 532 _dw_free_pkt(dev->priv); 533 534 return 0; 535 } 536 537 static void dw_eth_halt(struct eth_device *dev) 538 { 539 return _dw_eth_halt(dev->priv); 540 } 541 542 static int dw_write_hwaddr(struct eth_device *dev) 543 { 544 return _dw_write_hwaddr(dev->priv, dev->enetaddr); 545 } 546 547 int designware_initialize(ulong base_addr, u32 interface) 548 { 549 struct eth_device *dev; 550 struct dw_eth_dev *priv; 551 552 dev = (struct eth_device *) malloc(sizeof(struct eth_device)); 553 if (!dev) 554 return -ENOMEM; 555 556 /* 557 * Since the priv structure contains the descriptors which need a strict 558 * buswidth alignment, memalign is used to allocate memory 559 */ 560 priv = (struct dw_eth_dev *) memalign(ARCH_DMA_MINALIGN, 561 sizeof(struct dw_eth_dev)); 562 if (!priv) { 563 free(dev); 564 return -ENOMEM; 565 } 566 567 if ((phys_addr_t)priv + sizeof(*priv) > (1ULL << 32)) { 568 printf("designware: buffers are outside DMA memory\n"); 569 return -EINVAL; 570 } 571 572 memset(dev, 0, sizeof(struct eth_device)); 573 memset(priv, 0, sizeof(struct dw_eth_dev)); 574 575 sprintf(dev->name, "dwmac.%lx", base_addr); 576 dev->iobase = (int)base_addr; 577 dev->priv = priv; 578 579 priv->dev = dev; 580 priv->mac_regs_p = (struct eth_mac_regs *)base_addr; 581 priv->dma_regs_p = (struct eth_dma_regs *)(base_addr + 582 DW_DMA_BASE_OFFSET); 583 584 dev->init = dw_eth_init; 585 dev->send = dw_eth_send; 586 dev->recv = dw_eth_recv; 587 dev->halt = dw_eth_halt; 588 dev->write_hwaddr = dw_write_hwaddr; 589 590 eth_register(dev); 591 592 priv->interface = interface; 593 594 dw_mdio_init(dev->name, priv->mac_regs_p); 595 priv->bus = miiphy_get_dev_by_name(dev->name); 596 597 return dw_phy_init(priv, dev); 598 } 599 #endif 600 601 #ifdef CONFIG_DM_ETH 602 static int designware_eth_start(struct udevice *dev) 603 { 604 struct eth_pdata *pdata = dev_get_platdata(dev); 605 struct dw_eth_dev *priv = dev_get_priv(dev); 606 int ret; 607 608 ret = designware_eth_init(priv, pdata->enetaddr); 609 if (ret) 610 return ret; 611 ret = designware_eth_enable(priv); 612 if (ret) 613 return ret; 614 615 return 0; 616 } 617 618 int designware_eth_send(struct udevice *dev, void *packet, int length) 619 { 620 struct dw_eth_dev *priv = dev_get_priv(dev); 621 622 return _dw_eth_send(priv, packet, length); 623 } 624 625 int designware_eth_recv(struct udevice *dev, int flags, uchar **packetp) 626 { 627 struct dw_eth_dev *priv = dev_get_priv(dev); 628 629 return _dw_eth_recv(priv, packetp); 630 } 631 632 int designware_eth_free_pkt(struct udevice *dev, uchar *packet, int length) 633 { 634 struct dw_eth_dev *priv = dev_get_priv(dev); 635 636 return _dw_free_pkt(priv); 637 } 638 639 void designware_eth_stop(struct udevice *dev) 640 { 641 struct dw_eth_dev *priv = dev_get_priv(dev); 642 643 return _dw_eth_halt(priv); 644 } 645 646 int designware_eth_write_hwaddr(struct udevice *dev) 647 { 648 struct eth_pdata *pdata = dev_get_platdata(dev); 649 struct dw_eth_dev *priv = dev_get_priv(dev); 650 651 return _dw_write_hwaddr(priv, pdata->enetaddr); 652 } 653 654 static int designware_eth_bind(struct udevice *dev) 655 { 656 #ifdef CONFIG_DM_PCI 657 static int num_cards; 658 char name[20]; 659 660 /* Create a unique device name for PCI type devices */ 661 if (device_is_on_pci_bus(dev)) { 662 sprintf(name, "eth_designware#%u", num_cards++); 663 device_set_name(dev, name); 664 } 665 #endif 666 667 return 0; 668 } 669 670 int designware_eth_probe(struct udevice *dev) 671 { 672 struct eth_pdata *pdata = dev_get_platdata(dev); 673 struct dw_eth_dev *priv = dev_get_priv(dev); 674 u32 iobase = pdata->iobase; 675 ulong ioaddr; 676 int ret; 677 struct reset_ctl_bulk reset_bulk; 678 #ifdef CONFIG_CLK 679 int i, err, clock_nb; 680 681 priv->clock_count = 0; 682 clock_nb = dev_count_phandle_with_args(dev, "clocks", "#clock-cells"); 683 if (clock_nb > 0) { 684 priv->clocks = devm_kcalloc(dev, clock_nb, sizeof(struct clk), 685 GFP_KERNEL); 686 if (!priv->clocks) 687 return -ENOMEM; 688 689 for (i = 0; i < clock_nb; i++) { 690 err = clk_get_by_index(dev, i, &priv->clocks[i]); 691 if (err < 0) 692 break; 693 694 err = clk_enable(&priv->clocks[i]); 695 if (err && err != -ENOSYS && err != -ENOTSUPP) { 696 pr_err("failed to enable clock %d\n", i); 697 clk_free(&priv->clocks[i]); 698 goto clk_err; 699 } 700 priv->clock_count++; 701 } 702 } else if (clock_nb != -ENOENT) { 703 pr_err("failed to get clock phandle(%d)\n", clock_nb); 704 return clock_nb; 705 } 706 #endif 707 708 #if defined(CONFIG_DM_REGULATOR) 709 struct udevice *phy_supply; 710 711 ret = device_get_supply_regulator(dev, "phy-supply", 712 &phy_supply); 713 if (ret) { 714 debug("%s: No phy supply\n", dev->name); 715 } else { 716 ret = regulator_set_enable(phy_supply, true); 717 if (ret) { 718 puts("Error enabling phy supply\n"); 719 return ret; 720 } 721 } 722 #endif 723 724 ret = reset_get_bulk(dev, &reset_bulk); 725 if (ret) 726 dev_warn(dev, "Can't get reset: %d\n", ret); 727 else 728 reset_deassert_bulk(&reset_bulk); 729 730 #ifdef CONFIG_DM_PCI 731 /* 732 * If we are on PCI bus, either directly attached to a PCI root port, 733 * or via a PCI bridge, fill in platdata before we probe the hardware. 734 */ 735 if (device_is_on_pci_bus(dev)) { 736 dm_pci_read_config32(dev, PCI_BASE_ADDRESS_0, &iobase); 737 iobase &= PCI_BASE_ADDRESS_MEM_MASK; 738 iobase = dm_pci_mem_to_phys(dev, iobase); 739 740 pdata->iobase = iobase; 741 pdata->phy_interface = PHY_INTERFACE_MODE_RMII; 742 } 743 #endif 744 745 debug("%s, iobase=%x, priv=%p\n", __func__, iobase, priv); 746 ioaddr = iobase; 747 priv->mac_regs_p = (struct eth_mac_regs *)ioaddr; 748 priv->dma_regs_p = (struct eth_dma_regs *)(ioaddr + DW_DMA_BASE_OFFSET); 749 priv->interface = pdata->phy_interface; 750 priv->max_speed = pdata->max_speed; 751 752 dw_mdio_init(dev->name, dev); 753 priv->bus = miiphy_get_dev_by_name(dev->name); 754 755 ret = dw_phy_init(priv, dev); 756 debug("%s, ret=%d\n", __func__, ret); 757 758 return ret; 759 760 #ifdef CONFIG_CLK 761 clk_err: 762 ret = clk_release_all(priv->clocks, priv->clock_count); 763 if (ret) 764 pr_err("failed to disable all clocks\n"); 765 766 return err; 767 #endif 768 } 769 770 static int designware_eth_remove(struct udevice *dev) 771 { 772 struct dw_eth_dev *priv = dev_get_priv(dev); 773 774 free(priv->phydev); 775 mdio_unregister(priv->bus); 776 mdio_free(priv->bus); 777 778 #ifdef CONFIG_CLK 779 return clk_release_all(priv->clocks, priv->clock_count); 780 #else 781 return 0; 782 #endif 783 } 784 785 const struct eth_ops designware_eth_ops = { 786 .start = designware_eth_start, 787 .send = designware_eth_send, 788 .recv = designware_eth_recv, 789 .free_pkt = designware_eth_free_pkt, 790 .stop = designware_eth_stop, 791 .write_hwaddr = designware_eth_write_hwaddr, 792 }; 793 794 int designware_eth_ofdata_to_platdata(struct udevice *dev) 795 { 796 struct dw_eth_pdata *dw_pdata = dev_get_platdata(dev); 797 #ifdef CONFIG_DM_GPIO 798 struct dw_eth_dev *priv = dev_get_priv(dev); 799 #endif 800 struct eth_pdata *pdata = &dw_pdata->eth_pdata; 801 const char *phy_mode; 802 #ifdef CONFIG_DM_GPIO 803 int reset_flags = GPIOD_IS_OUT; 804 #endif 805 int ret = 0; 806 807 pdata->iobase = dev_read_addr(dev); 808 pdata->phy_interface = -1; 809 phy_mode = dev_read_string(dev, "phy-mode"); 810 if (phy_mode) 811 pdata->phy_interface = phy_get_interface_by_name(phy_mode); 812 if (pdata->phy_interface == -1) { 813 debug("%s: Invalid PHY interface '%s'\n", __func__, phy_mode); 814 return -EINVAL; 815 } 816 817 pdata->max_speed = dev_read_u32_default(dev, "max-speed", 0); 818 819 #ifdef CONFIG_DM_GPIO 820 if (dev_read_bool(dev, "snps,reset-active-low")) 821 reset_flags |= GPIOD_ACTIVE_LOW; 822 823 ret = gpio_request_by_name(dev, "snps,reset-gpio", 0, 824 &priv->reset_gpio, reset_flags); 825 if (ret == 0) { 826 ret = dev_read_u32_array(dev, "snps,reset-delays-us", 827 dw_pdata->reset_delays, 3); 828 } else if (ret == -ENOENT) { 829 ret = 0; 830 } 831 #endif 832 833 return ret; 834 } 835 836 static const struct udevice_id designware_eth_ids[] = { 837 { .compatible = "allwinner,sun7i-a20-gmac" }, 838 { .compatible = "altr,socfpga-stmmac" }, 839 { .compatible = "amlogic,meson6-dwmac" }, 840 { .compatible = "amlogic,meson-gx-dwmac" }, 841 { .compatible = "amlogic,meson-gxbb-dwmac" }, 842 { .compatible = "amlogic,meson-axg-dwmac" }, 843 { .compatible = "st,stm32-dwmac" }, 844 { } 845 }; 846 847 U_BOOT_DRIVER(eth_designware) = { 848 .name = "eth_designware", 849 .id = UCLASS_ETH, 850 .of_match = designware_eth_ids, 851 .ofdata_to_platdata = designware_eth_ofdata_to_platdata, 852 .bind = designware_eth_bind, 853 .probe = designware_eth_probe, 854 .remove = designware_eth_remove, 855 .ops = &designware_eth_ops, 856 .priv_auto_alloc_size = sizeof(struct dw_eth_dev), 857 .platdata_auto_alloc_size = sizeof(struct dw_eth_pdata), 858 .flags = DM_FLAG_ALLOC_PRIV_DMA, 859 }; 860 861 static struct pci_device_id supported[] = { 862 { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_QRK_EMAC) }, 863 { } 864 }; 865 866 U_BOOT_PCI_DEVICE(eth_designware, supported); 867 #endif 868