xref: /openbmc/u-boot/drivers/net/designware.c (revision 7f6a6db6)
1 /*
2  * (C) Copyright 2010
3  * Vipin Kumar, ST Micoelectronics, vipin.kumar@st.com.
4  *
5  * SPDX-License-Identifier:	GPL-2.0+
6  */
7 
8 /*
9  * Designware ethernet IP driver for u-boot
10  */
11 
12 #include <common.h>
13 #include <miiphy.h>
14 #include <malloc.h>
15 #include <linux/compiler.h>
16 #include <linux/err.h>
17 #include <asm/io.h>
18 #include "designware.h"
19 
20 #if !defined(CONFIG_PHYLIB)
21 # error "DesignWare Ether MAC requires PHYLIB - missing CONFIG_PHYLIB"
22 #endif
23 
24 static int dw_mdio_read(struct mii_dev *bus, int addr, int devad, int reg)
25 {
26 	struct eth_mac_regs *mac_p = bus->priv;
27 	ulong start;
28 	u16 miiaddr;
29 	int timeout = CONFIG_MDIO_TIMEOUT;
30 
31 	miiaddr = ((addr << MIIADDRSHIFT) & MII_ADDRMSK) |
32 		  ((reg << MIIREGSHIFT) & MII_REGMSK);
33 
34 	writel(miiaddr | MII_CLKRANGE_150_250M | MII_BUSY, &mac_p->miiaddr);
35 
36 	start = get_timer(0);
37 	while (get_timer(start) < timeout) {
38 		if (!(readl(&mac_p->miiaddr) & MII_BUSY))
39 			return readl(&mac_p->miidata);
40 		udelay(10);
41 	};
42 
43 	return -1;
44 }
45 
46 static int dw_mdio_write(struct mii_dev *bus, int addr, int devad, int reg,
47 			u16 val)
48 {
49 	struct eth_mac_regs *mac_p = bus->priv;
50 	ulong start;
51 	u16 miiaddr;
52 	int ret = -1, timeout = CONFIG_MDIO_TIMEOUT;
53 
54 	writel(val, &mac_p->miidata);
55 	miiaddr = ((addr << MIIADDRSHIFT) & MII_ADDRMSK) |
56 		  ((reg << MIIREGSHIFT) & MII_REGMSK) | MII_WRITE;
57 
58 	writel(miiaddr | MII_CLKRANGE_150_250M | MII_BUSY, &mac_p->miiaddr);
59 
60 	start = get_timer(0);
61 	while (get_timer(start) < timeout) {
62 		if (!(readl(&mac_p->miiaddr) & MII_BUSY)) {
63 			ret = 0;
64 			break;
65 		}
66 		udelay(10);
67 	};
68 
69 	return ret;
70 }
71 
72 static int dw_mdio_init(char *name, struct eth_mac_regs *mac_regs_p)
73 {
74 	struct mii_dev *bus = mdio_alloc();
75 
76 	if (!bus) {
77 		printf("Failed to allocate MDIO bus\n");
78 		return -1;
79 	}
80 
81 	bus->read = dw_mdio_read;
82 	bus->write = dw_mdio_write;
83 	sprintf(bus->name, name);
84 
85 	bus->priv = (void *)mac_regs_p;
86 
87 	return mdio_register(bus);
88 }
89 
90 static void tx_descs_init(struct eth_device *dev)
91 {
92 	struct dw_eth_dev *priv = dev->priv;
93 	struct eth_dma_regs *dma_p = priv->dma_regs_p;
94 	struct dmamacdescr *desc_table_p = &priv->tx_mac_descrtable[0];
95 	char *txbuffs = &priv->txbuffs[0];
96 	struct dmamacdescr *desc_p;
97 	u32 idx;
98 
99 	for (idx = 0; idx < CONFIG_TX_DESCR_NUM; idx++) {
100 		desc_p = &desc_table_p[idx];
101 		desc_p->dmamac_addr = &txbuffs[idx * CONFIG_ETH_BUFSIZE];
102 		desc_p->dmamac_next = &desc_table_p[idx + 1];
103 
104 #if defined(CONFIG_DW_ALTDESCRIPTOR)
105 		desc_p->txrx_status &= ~(DESC_TXSTS_TXINT | DESC_TXSTS_TXLAST |
106 				DESC_TXSTS_TXFIRST | DESC_TXSTS_TXCRCDIS | \
107 				DESC_TXSTS_TXCHECKINSCTRL | \
108 				DESC_TXSTS_TXRINGEND | DESC_TXSTS_TXPADDIS);
109 
110 		desc_p->txrx_status |= DESC_TXSTS_TXCHAIN;
111 		desc_p->dmamac_cntl = 0;
112 		desc_p->txrx_status &= ~(DESC_TXSTS_MSK | DESC_TXSTS_OWNBYDMA);
113 #else
114 		desc_p->dmamac_cntl = DESC_TXCTRL_TXCHAIN;
115 		desc_p->txrx_status = 0;
116 #endif
117 	}
118 
119 	/* Correcting the last pointer of the chain */
120 	desc_p->dmamac_next = &desc_table_p[0];
121 
122 	/* Flush all Tx buffer descriptors at once */
123 	flush_dcache_range((unsigned int)priv->tx_mac_descrtable,
124 			   (unsigned int)priv->tx_mac_descrtable +
125 			   sizeof(priv->tx_mac_descrtable));
126 
127 	writel((ulong)&desc_table_p[0], &dma_p->txdesclistaddr);
128 	priv->tx_currdescnum = 0;
129 }
130 
131 static void rx_descs_init(struct eth_device *dev)
132 {
133 	struct dw_eth_dev *priv = dev->priv;
134 	struct eth_dma_regs *dma_p = priv->dma_regs_p;
135 	struct dmamacdescr *desc_table_p = &priv->rx_mac_descrtable[0];
136 	char *rxbuffs = &priv->rxbuffs[0];
137 	struct dmamacdescr *desc_p;
138 	u32 idx;
139 
140 	/* Before passing buffers to GMAC we need to make sure zeros
141 	 * written there right after "priv" structure allocation were
142 	 * flushed into RAM.
143 	 * Otherwise there's a chance to get some of them flushed in RAM when
144 	 * GMAC is already pushing data to RAM via DMA. This way incoming from
145 	 * GMAC data will be corrupted. */
146 	flush_dcache_range((unsigned int)rxbuffs, (unsigned int)rxbuffs +
147 			   RX_TOTAL_BUFSIZE);
148 
149 	for (idx = 0; idx < CONFIG_RX_DESCR_NUM; idx++) {
150 		desc_p = &desc_table_p[idx];
151 		desc_p->dmamac_addr = &rxbuffs[idx * CONFIG_ETH_BUFSIZE];
152 		desc_p->dmamac_next = &desc_table_p[idx + 1];
153 
154 		desc_p->dmamac_cntl =
155 			(MAC_MAX_FRAME_SZ & DESC_RXCTRL_SIZE1MASK) | \
156 				      DESC_RXCTRL_RXCHAIN;
157 
158 		desc_p->txrx_status = DESC_RXSTS_OWNBYDMA;
159 	}
160 
161 	/* Correcting the last pointer of the chain */
162 	desc_p->dmamac_next = &desc_table_p[0];
163 
164 	/* Flush all Rx buffer descriptors at once */
165 	flush_dcache_range((unsigned int)priv->rx_mac_descrtable,
166 			   (unsigned int)priv->rx_mac_descrtable +
167 			   sizeof(priv->rx_mac_descrtable));
168 
169 	writel((ulong)&desc_table_p[0], &dma_p->rxdesclistaddr);
170 	priv->rx_currdescnum = 0;
171 }
172 
173 static int dw_write_hwaddr(struct eth_device *dev)
174 {
175 	struct dw_eth_dev *priv = dev->priv;
176 	struct eth_mac_regs *mac_p = priv->mac_regs_p;
177 	u32 macid_lo, macid_hi;
178 	u8 *mac_id = &dev->enetaddr[0];
179 
180 	macid_lo = mac_id[0] + (mac_id[1] << 8) + (mac_id[2] << 16) +
181 		   (mac_id[3] << 24);
182 	macid_hi = mac_id[4] + (mac_id[5] << 8);
183 
184 	writel(macid_hi, &mac_p->macaddr0hi);
185 	writel(macid_lo, &mac_p->macaddr0lo);
186 
187 	return 0;
188 }
189 
190 static void dw_adjust_link(struct eth_mac_regs *mac_p,
191 			   struct phy_device *phydev)
192 {
193 	u32 conf = readl(&mac_p->conf) | FRAMEBURSTENABLE | DISABLERXOWN;
194 
195 	if (!phydev->link) {
196 		printf("%s: No link.\n", phydev->dev->name);
197 		return;
198 	}
199 
200 	if (phydev->speed != 1000)
201 		conf |= MII_PORTSELECT;
202 
203 	if (phydev->speed == 100)
204 		conf |= FES_100;
205 
206 	if (phydev->duplex)
207 		conf |= FULLDPLXMODE;
208 
209 	writel(conf, &mac_p->conf);
210 
211 	printf("Speed: %d, %s duplex%s\n", phydev->speed,
212 	       (phydev->duplex) ? "full" : "half",
213 	       (phydev->port == PORT_FIBRE) ? ", fiber mode" : "");
214 }
215 
216 static void dw_eth_halt(struct eth_device *dev)
217 {
218 	struct dw_eth_dev *priv = dev->priv;
219 	struct eth_mac_regs *mac_p = priv->mac_regs_p;
220 	struct eth_dma_regs *dma_p = priv->dma_regs_p;
221 
222 	writel(readl(&mac_p->conf) & ~(RXENABLE | TXENABLE), &mac_p->conf);
223 	writel(readl(&dma_p->opmode) & ~(RXSTART | TXSTART), &dma_p->opmode);
224 
225 	phy_shutdown(priv->phydev);
226 }
227 
228 static int dw_eth_init(struct eth_device *dev, bd_t *bis)
229 {
230 	struct dw_eth_dev *priv = dev->priv;
231 	struct eth_mac_regs *mac_p = priv->mac_regs_p;
232 	struct eth_dma_regs *dma_p = priv->dma_regs_p;
233 	unsigned int start;
234 
235 	writel(readl(&dma_p->busmode) | DMAMAC_SRST, &dma_p->busmode);
236 
237 	start = get_timer(0);
238 	while (readl(&dma_p->busmode) & DMAMAC_SRST) {
239 		if (get_timer(start) >= CONFIG_MACRESET_TIMEOUT)
240 			return -1;
241 
242 		mdelay(100);
243 	};
244 
245 	/* Soft reset above clears HW address registers.
246 	 * So we have to set it here once again */
247 	dw_write_hwaddr(dev);
248 
249 	rx_descs_init(dev);
250 	tx_descs_init(dev);
251 
252 	writel(FIXEDBURST | PRIORXTX_41 | BURST_16, &dma_p->busmode);
253 
254 	writel(readl(&dma_p->opmode) | FLUSHTXFIFO | STOREFORWARD,
255 	       &dma_p->opmode);
256 
257 	writel(readl(&dma_p->opmode) | RXSTART | TXSTART, &dma_p->opmode);
258 
259 	/* Start up the PHY */
260 	if (phy_startup(priv->phydev)) {
261 		printf("Could not initialize PHY %s\n",
262 		       priv->phydev->dev->name);
263 		return -1;
264 	}
265 
266 	dw_adjust_link(mac_p, priv->phydev);
267 
268 	if (!priv->phydev->link)
269 		return -1;
270 
271 	writel(readl(&mac_p->conf) | RXENABLE | TXENABLE, &mac_p->conf);
272 
273 	return 0;
274 }
275 
276 static int dw_eth_send(struct eth_device *dev, void *packet, int length)
277 {
278 	struct dw_eth_dev *priv = dev->priv;
279 	struct eth_dma_regs *dma_p = priv->dma_regs_p;
280 	u32 desc_num = priv->tx_currdescnum;
281 	struct dmamacdescr *desc_p = &priv->tx_mac_descrtable[desc_num];
282 
283 	/* Invalidate only "status" field for the following check */
284 	invalidate_dcache_range((unsigned long)&desc_p->txrx_status,
285 				(unsigned long)&desc_p->txrx_status +
286 				sizeof(desc_p->txrx_status));
287 
288 	/* Check if the descriptor is owned by CPU */
289 	if (desc_p->txrx_status & DESC_TXSTS_OWNBYDMA) {
290 		printf("CPU not owner of tx frame\n");
291 		return -1;
292 	}
293 
294 	memcpy((void *)desc_p->dmamac_addr, packet, length);
295 
296 	/* Flush data to be sent */
297 	flush_dcache_range((unsigned long)desc_p->dmamac_addr,
298 			   (unsigned long)desc_p->dmamac_addr + length);
299 
300 #if defined(CONFIG_DW_ALTDESCRIPTOR)
301 	desc_p->txrx_status |= DESC_TXSTS_TXFIRST | DESC_TXSTS_TXLAST;
302 	desc_p->dmamac_cntl |= (length << DESC_TXCTRL_SIZE1SHFT) & \
303 			       DESC_TXCTRL_SIZE1MASK;
304 
305 	desc_p->txrx_status &= ~(DESC_TXSTS_MSK);
306 	desc_p->txrx_status |= DESC_TXSTS_OWNBYDMA;
307 #else
308 	desc_p->dmamac_cntl |= ((length << DESC_TXCTRL_SIZE1SHFT) & \
309 			       DESC_TXCTRL_SIZE1MASK) | DESC_TXCTRL_TXLAST | \
310 			       DESC_TXCTRL_TXFIRST;
311 
312 	desc_p->txrx_status = DESC_TXSTS_OWNBYDMA;
313 #endif
314 
315 	/* Flush modified buffer descriptor */
316 	flush_dcache_range((unsigned long)desc_p,
317 			   (unsigned long)desc_p + sizeof(struct dmamacdescr));
318 
319 	/* Test the wrap-around condition. */
320 	if (++desc_num >= CONFIG_TX_DESCR_NUM)
321 		desc_num = 0;
322 
323 	priv->tx_currdescnum = desc_num;
324 
325 	/* Start the transmission */
326 	writel(POLL_DATA, &dma_p->txpolldemand);
327 
328 	return 0;
329 }
330 
331 static int dw_eth_recv(struct eth_device *dev)
332 {
333 	struct dw_eth_dev *priv = dev->priv;
334 	u32 status, desc_num = priv->rx_currdescnum;
335 	struct dmamacdescr *desc_p = &priv->rx_mac_descrtable[desc_num];
336 	int length = 0;
337 
338 	/* Invalidate entire buffer descriptor */
339 	invalidate_dcache_range((unsigned long)desc_p,
340 				(unsigned long)desc_p +
341 				sizeof(struct dmamacdescr));
342 
343 	status = desc_p->txrx_status;
344 
345 	/* Check  if the owner is the CPU */
346 	if (!(status & DESC_RXSTS_OWNBYDMA)) {
347 
348 		length = (status & DESC_RXSTS_FRMLENMSK) >> \
349 			 DESC_RXSTS_FRMLENSHFT;
350 
351 		/* Invalidate received data */
352 		invalidate_dcache_range((unsigned long)desc_p->dmamac_addr,
353 					(unsigned long)desc_p->dmamac_addr +
354 					length);
355 
356 		NetReceive(desc_p->dmamac_addr, length);
357 
358 		/*
359 		 * Make the current descriptor valid again and go to
360 		 * the next one
361 		 */
362 		desc_p->txrx_status |= DESC_RXSTS_OWNBYDMA;
363 
364 		/* Flush only status field - others weren't changed */
365 		flush_dcache_range((unsigned long)&desc_p->txrx_status,
366 				   (unsigned long)&desc_p->txrx_status +
367 				   sizeof(desc_p->txrx_status));
368 
369 		/* Test the wrap-around condition. */
370 		if (++desc_num >= CONFIG_RX_DESCR_NUM)
371 			desc_num = 0;
372 	}
373 
374 	priv->rx_currdescnum = desc_num;
375 
376 	return length;
377 }
378 
379 static int dw_phy_init(struct eth_device *dev)
380 {
381 	struct dw_eth_dev *priv = dev->priv;
382 	struct phy_device *phydev;
383 	int mask = 0xffffffff;
384 
385 #ifdef CONFIG_PHY_ADDR
386 	mask = 1 << CONFIG_PHY_ADDR;
387 #endif
388 
389 	phydev = phy_find_by_mask(priv->bus, mask, priv->interface);
390 	if (!phydev)
391 		return -1;
392 
393 	phy_connect_dev(phydev, dev);
394 
395 	phydev->supported &= PHY_GBIT_FEATURES;
396 	phydev->advertising = phydev->supported;
397 
398 	priv->phydev = phydev;
399 	phy_config(phydev);
400 
401 	return 1;
402 }
403 
404 int designware_initialize(ulong base_addr, u32 interface)
405 {
406 	struct eth_device *dev;
407 	struct dw_eth_dev *priv;
408 
409 	dev = (struct eth_device *) malloc(sizeof(struct eth_device));
410 	if (!dev)
411 		return -ENOMEM;
412 
413 	/*
414 	 * Since the priv structure contains the descriptors which need a strict
415 	 * buswidth alignment, memalign is used to allocate memory
416 	 */
417 	priv = (struct dw_eth_dev *) memalign(16, sizeof(struct dw_eth_dev));
418 	if (!priv) {
419 		free(dev);
420 		return -ENOMEM;
421 	}
422 
423 	memset(dev, 0, sizeof(struct eth_device));
424 	memset(priv, 0, sizeof(struct dw_eth_dev));
425 
426 	sprintf(dev->name, "dwmac.%lx", base_addr);
427 	dev->iobase = (int)base_addr;
428 	dev->priv = priv;
429 
430 	priv->dev = dev;
431 	priv->mac_regs_p = (struct eth_mac_regs *)base_addr;
432 	priv->dma_regs_p = (struct eth_dma_regs *)(base_addr +
433 			DW_DMA_BASE_OFFSET);
434 
435 	dev->init = dw_eth_init;
436 	dev->send = dw_eth_send;
437 	dev->recv = dw_eth_recv;
438 	dev->halt = dw_eth_halt;
439 	dev->write_hwaddr = dw_write_hwaddr;
440 
441 	eth_register(dev);
442 
443 	priv->interface = interface;
444 
445 	dw_mdio_init(dev->name, priv->mac_regs_p);
446 	priv->bus = miiphy_get_dev_by_name(dev->name);
447 
448 	return dw_phy_init(dev);
449 }
450