xref: /openbmc/u-boot/drivers/net/designware.c (revision 173f023f)
1 /*
2  * (C) Copyright 2010
3  * Vipin Kumar, ST Micoelectronics, vipin.kumar@st.com.
4  *
5  * SPDX-License-Identifier:	GPL-2.0+
6  */
7 
8 /*
9  * Designware ethernet IP driver for U-Boot
10  */
11 
12 #include <common.h>
13 #include <clk.h>
14 #include <dm.h>
15 #include <errno.h>
16 #include <miiphy.h>
17 #include <malloc.h>
18 #include <pci.h>
19 #include <linux/compiler.h>
20 #include <linux/err.h>
21 #include <linux/kernel.h>
22 #include <asm/io.h>
23 #include <power/regulator.h>
24 #include "designware.h"
25 
26 DECLARE_GLOBAL_DATA_PTR;
27 
28 static int dw_mdio_read(struct mii_dev *bus, int addr, int devad, int reg)
29 {
30 #ifdef CONFIG_DM_ETH
31 	struct dw_eth_dev *priv = dev_get_priv((struct udevice *)bus->priv);
32 	struct eth_mac_regs *mac_p = priv->mac_regs_p;
33 #else
34 	struct eth_mac_regs *mac_p = bus->priv;
35 #endif
36 	ulong start;
37 	u16 miiaddr;
38 	int timeout = CONFIG_MDIO_TIMEOUT;
39 
40 	miiaddr = ((addr << MIIADDRSHIFT) & MII_ADDRMSK) |
41 		  ((reg << MIIREGSHIFT) & MII_REGMSK);
42 
43 	writel(miiaddr | MII_CLKRANGE_150_250M | MII_BUSY, &mac_p->miiaddr);
44 
45 	start = get_timer(0);
46 	while (get_timer(start) < timeout) {
47 		if (!(readl(&mac_p->miiaddr) & MII_BUSY))
48 			return readl(&mac_p->miidata);
49 		udelay(10);
50 	};
51 
52 	return -ETIMEDOUT;
53 }
54 
55 static int dw_mdio_write(struct mii_dev *bus, int addr, int devad, int reg,
56 			u16 val)
57 {
58 #ifdef CONFIG_DM_ETH
59 	struct dw_eth_dev *priv = dev_get_priv((struct udevice *)bus->priv);
60 	struct eth_mac_regs *mac_p = priv->mac_regs_p;
61 #else
62 	struct eth_mac_regs *mac_p = bus->priv;
63 #endif
64 	ulong start;
65 	u16 miiaddr;
66 	int ret = -ETIMEDOUT, timeout = CONFIG_MDIO_TIMEOUT;
67 
68 	writel(val, &mac_p->miidata);
69 	miiaddr = ((addr << MIIADDRSHIFT) & MII_ADDRMSK) |
70 		  ((reg << MIIREGSHIFT) & MII_REGMSK) | MII_WRITE;
71 
72 	writel(miiaddr | MII_CLKRANGE_150_250M | MII_BUSY, &mac_p->miiaddr);
73 
74 	start = get_timer(0);
75 	while (get_timer(start) < timeout) {
76 		if (!(readl(&mac_p->miiaddr) & MII_BUSY)) {
77 			ret = 0;
78 			break;
79 		}
80 		udelay(10);
81 	};
82 
83 	return ret;
84 }
85 
86 #if defined(CONFIG_DM_ETH) && defined(CONFIG_DM_GPIO)
87 static int dw_mdio_reset(struct mii_dev *bus)
88 {
89 	struct udevice *dev = bus->priv;
90 	struct dw_eth_dev *priv = dev_get_priv(dev);
91 	struct dw_eth_pdata *pdata = dev_get_platdata(dev);
92 	int ret;
93 
94 	if (!dm_gpio_is_valid(&priv->reset_gpio))
95 		return 0;
96 
97 	/* reset the phy */
98 	ret = dm_gpio_set_value(&priv->reset_gpio, 0);
99 	if (ret)
100 		return ret;
101 
102 	udelay(pdata->reset_delays[0]);
103 
104 	ret = dm_gpio_set_value(&priv->reset_gpio, 1);
105 	if (ret)
106 		return ret;
107 
108 	udelay(pdata->reset_delays[1]);
109 
110 	ret = dm_gpio_set_value(&priv->reset_gpio, 0);
111 	if (ret)
112 		return ret;
113 
114 	udelay(pdata->reset_delays[2]);
115 
116 	return 0;
117 }
118 #endif
119 
120 static int dw_mdio_init(const char *name, void *priv)
121 {
122 	struct mii_dev *bus = mdio_alloc();
123 
124 	if (!bus) {
125 		printf("Failed to allocate MDIO bus\n");
126 		return -ENOMEM;
127 	}
128 
129 	bus->read = dw_mdio_read;
130 	bus->write = dw_mdio_write;
131 	snprintf(bus->name, sizeof(bus->name), "%s", name);
132 #if defined(CONFIG_DM_ETH) && defined(CONFIG_DM_GPIO)
133 	bus->reset = dw_mdio_reset;
134 #endif
135 
136 	bus->priv = priv;
137 
138 	return mdio_register(bus);
139 }
140 
141 static void tx_descs_init(struct dw_eth_dev *priv)
142 {
143 	struct eth_dma_regs *dma_p = priv->dma_regs_p;
144 	struct dmamacdescr *desc_table_p = &priv->tx_mac_descrtable[0];
145 	char *txbuffs = &priv->txbuffs[0];
146 	struct dmamacdescr *desc_p;
147 	u32 idx;
148 
149 	for (idx = 0; idx < CONFIG_TX_DESCR_NUM; idx++) {
150 		desc_p = &desc_table_p[idx];
151 		desc_p->dmamac_addr = (ulong)&txbuffs[idx * CONFIG_ETH_BUFSIZE];
152 		desc_p->dmamac_next = (ulong)&desc_table_p[idx + 1];
153 
154 #if defined(CONFIG_DW_ALTDESCRIPTOR)
155 		desc_p->txrx_status &= ~(DESC_TXSTS_TXINT | DESC_TXSTS_TXLAST |
156 				DESC_TXSTS_TXFIRST | DESC_TXSTS_TXCRCDIS |
157 				DESC_TXSTS_TXCHECKINSCTRL |
158 				DESC_TXSTS_TXRINGEND | DESC_TXSTS_TXPADDIS);
159 
160 		desc_p->txrx_status |= DESC_TXSTS_TXCHAIN;
161 		desc_p->dmamac_cntl = 0;
162 		desc_p->txrx_status &= ~(DESC_TXSTS_MSK | DESC_TXSTS_OWNBYDMA);
163 #else
164 		desc_p->dmamac_cntl = DESC_TXCTRL_TXCHAIN;
165 		desc_p->txrx_status = 0;
166 #endif
167 	}
168 
169 	/* Correcting the last pointer of the chain */
170 	desc_p->dmamac_next = (ulong)&desc_table_p[0];
171 
172 	/* Flush all Tx buffer descriptors at once */
173 	flush_dcache_range((ulong)priv->tx_mac_descrtable,
174 			   (ulong)priv->tx_mac_descrtable +
175 			   sizeof(priv->tx_mac_descrtable));
176 
177 	writel((ulong)&desc_table_p[0], &dma_p->txdesclistaddr);
178 	priv->tx_currdescnum = 0;
179 }
180 
181 static void rx_descs_init(struct dw_eth_dev *priv)
182 {
183 	struct eth_dma_regs *dma_p = priv->dma_regs_p;
184 	struct dmamacdescr *desc_table_p = &priv->rx_mac_descrtable[0];
185 	char *rxbuffs = &priv->rxbuffs[0];
186 	struct dmamacdescr *desc_p;
187 	u32 idx;
188 
189 	/* Before passing buffers to GMAC we need to make sure zeros
190 	 * written there right after "priv" structure allocation were
191 	 * flushed into RAM.
192 	 * Otherwise there's a chance to get some of them flushed in RAM when
193 	 * GMAC is already pushing data to RAM via DMA. This way incoming from
194 	 * GMAC data will be corrupted. */
195 	flush_dcache_range((ulong)rxbuffs, (ulong)rxbuffs + RX_TOTAL_BUFSIZE);
196 
197 	for (idx = 0; idx < CONFIG_RX_DESCR_NUM; idx++) {
198 		desc_p = &desc_table_p[idx];
199 		desc_p->dmamac_addr = (ulong)&rxbuffs[idx * CONFIG_ETH_BUFSIZE];
200 		desc_p->dmamac_next = (ulong)&desc_table_p[idx + 1];
201 
202 		desc_p->dmamac_cntl =
203 			(MAC_MAX_FRAME_SZ & DESC_RXCTRL_SIZE1MASK) |
204 				      DESC_RXCTRL_RXCHAIN;
205 
206 		desc_p->txrx_status = DESC_RXSTS_OWNBYDMA;
207 	}
208 
209 	/* Correcting the last pointer of the chain */
210 	desc_p->dmamac_next = (ulong)&desc_table_p[0];
211 
212 	/* Flush all Rx buffer descriptors at once */
213 	flush_dcache_range((ulong)priv->rx_mac_descrtable,
214 			   (ulong)priv->rx_mac_descrtable +
215 			   sizeof(priv->rx_mac_descrtable));
216 
217 	writel((ulong)&desc_table_p[0], &dma_p->rxdesclistaddr);
218 	priv->rx_currdescnum = 0;
219 }
220 
221 static int _dw_write_hwaddr(struct dw_eth_dev *priv, u8 *mac_id)
222 {
223 	struct eth_mac_regs *mac_p = priv->mac_regs_p;
224 	u32 macid_lo, macid_hi;
225 
226 	macid_lo = mac_id[0] + (mac_id[1] << 8) + (mac_id[2] << 16) +
227 		   (mac_id[3] << 24);
228 	macid_hi = mac_id[4] + (mac_id[5] << 8);
229 
230 	writel(macid_hi, &mac_p->macaddr0hi);
231 	writel(macid_lo, &mac_p->macaddr0lo);
232 
233 	return 0;
234 }
235 
236 static int dw_adjust_link(struct dw_eth_dev *priv, struct eth_mac_regs *mac_p,
237 			  struct phy_device *phydev)
238 {
239 	u32 conf = readl(&mac_p->conf) | FRAMEBURSTENABLE | DISABLERXOWN;
240 
241 	if (!phydev->link) {
242 		printf("%s: No link.\n", phydev->dev->name);
243 		return 0;
244 	}
245 
246 	if (phydev->speed != 1000)
247 		conf |= MII_PORTSELECT;
248 	else
249 		conf &= ~MII_PORTSELECT;
250 
251 	if (phydev->speed == 100)
252 		conf |= FES_100;
253 
254 	if (phydev->duplex)
255 		conf |= FULLDPLXMODE;
256 
257 	writel(conf, &mac_p->conf);
258 
259 	printf("Speed: %d, %s duplex%s\n", phydev->speed,
260 	       (phydev->duplex) ? "full" : "half",
261 	       (phydev->port == PORT_FIBRE) ? ", fiber mode" : "");
262 
263 	return 0;
264 }
265 
266 static void _dw_eth_halt(struct dw_eth_dev *priv)
267 {
268 	struct eth_mac_regs *mac_p = priv->mac_regs_p;
269 	struct eth_dma_regs *dma_p = priv->dma_regs_p;
270 
271 	writel(readl(&mac_p->conf) & ~(RXENABLE | TXENABLE), &mac_p->conf);
272 	writel(readl(&dma_p->opmode) & ~(RXSTART | TXSTART), &dma_p->opmode);
273 
274 	phy_shutdown(priv->phydev);
275 }
276 
277 int designware_eth_init(struct dw_eth_dev *priv, u8 *enetaddr)
278 {
279 	struct eth_mac_regs *mac_p = priv->mac_regs_p;
280 	struct eth_dma_regs *dma_p = priv->dma_regs_p;
281 	unsigned int start;
282 	int ret;
283 
284 	writel(readl(&dma_p->busmode) | DMAMAC_SRST, &dma_p->busmode);
285 
286 	start = get_timer(0);
287 	while (readl(&dma_p->busmode) & DMAMAC_SRST) {
288 		if (get_timer(start) >= CONFIG_MACRESET_TIMEOUT) {
289 			printf("DMA reset timeout\n");
290 			return -ETIMEDOUT;
291 		}
292 
293 		mdelay(100);
294 	};
295 
296 	/*
297 	 * Soft reset above clears HW address registers.
298 	 * So we have to set it here once again.
299 	 */
300 	_dw_write_hwaddr(priv, enetaddr);
301 
302 	rx_descs_init(priv);
303 	tx_descs_init(priv);
304 
305 	writel(FIXEDBURST | PRIORXTX_41 | DMA_PBL, &dma_p->busmode);
306 
307 #ifndef CONFIG_DW_MAC_FORCE_THRESHOLD_MODE
308 	writel(readl(&dma_p->opmode) | FLUSHTXFIFO | STOREFORWARD,
309 	       &dma_p->opmode);
310 #else
311 	writel(readl(&dma_p->opmode) | FLUSHTXFIFO,
312 	       &dma_p->opmode);
313 #endif
314 
315 	writel(readl(&dma_p->opmode) | RXSTART | TXSTART, &dma_p->opmode);
316 
317 #ifdef CONFIG_DW_AXI_BURST_LEN
318 	writel((CONFIG_DW_AXI_BURST_LEN & 0x1FF >> 1), &dma_p->axibus);
319 #endif
320 
321 	/* Start up the PHY */
322 	ret = phy_startup(priv->phydev);
323 	if (ret) {
324 		printf("Could not initialize PHY %s\n",
325 		       priv->phydev->dev->name);
326 		return ret;
327 	}
328 
329 	ret = dw_adjust_link(priv, mac_p, priv->phydev);
330 	if (ret)
331 		return ret;
332 
333 	return 0;
334 }
335 
336 int designware_eth_enable(struct dw_eth_dev *priv)
337 {
338 	struct eth_mac_regs *mac_p = priv->mac_regs_p;
339 
340 	if (!priv->phydev->link)
341 		return -EIO;
342 
343 	writel(readl(&mac_p->conf) | RXENABLE | TXENABLE, &mac_p->conf);
344 
345 	return 0;
346 }
347 
348 #define ETH_ZLEN	60
349 
350 static int _dw_eth_send(struct dw_eth_dev *priv, void *packet, int length)
351 {
352 	struct eth_dma_regs *dma_p = priv->dma_regs_p;
353 	u32 desc_num = priv->tx_currdescnum;
354 	struct dmamacdescr *desc_p = &priv->tx_mac_descrtable[desc_num];
355 	ulong desc_start = (ulong)desc_p;
356 	ulong desc_end = desc_start +
357 		roundup(sizeof(*desc_p), ARCH_DMA_MINALIGN);
358 	ulong data_start = desc_p->dmamac_addr;
359 	ulong data_end = data_start + roundup(length, ARCH_DMA_MINALIGN);
360 	/*
361 	 * Strictly we only need to invalidate the "txrx_status" field
362 	 * for the following check, but on some platforms we cannot
363 	 * invalidate only 4 bytes, so we flush the entire descriptor,
364 	 * which is 16 bytes in total. This is safe because the
365 	 * individual descriptors in the array are each aligned to
366 	 * ARCH_DMA_MINALIGN and padded appropriately.
367 	 */
368 	invalidate_dcache_range(desc_start, desc_end);
369 
370 	/* Check if the descriptor is owned by CPU */
371 	if (desc_p->txrx_status & DESC_TXSTS_OWNBYDMA) {
372 		printf("CPU not owner of tx frame\n");
373 		return -EPERM;
374 	}
375 
376 	length = max(length, ETH_ZLEN);
377 
378 	memcpy((void *)data_start, packet, length);
379 
380 	/* Flush data to be sent */
381 	flush_dcache_range(data_start, data_end);
382 
383 #if defined(CONFIG_DW_ALTDESCRIPTOR)
384 	desc_p->txrx_status |= DESC_TXSTS_TXFIRST | DESC_TXSTS_TXLAST;
385 	desc_p->dmamac_cntl |= (length << DESC_TXCTRL_SIZE1SHFT) &
386 			       DESC_TXCTRL_SIZE1MASK;
387 
388 	desc_p->txrx_status &= ~(DESC_TXSTS_MSK);
389 	desc_p->txrx_status |= DESC_TXSTS_OWNBYDMA;
390 #else
391 	desc_p->dmamac_cntl |= ((length << DESC_TXCTRL_SIZE1SHFT) &
392 			       DESC_TXCTRL_SIZE1MASK) | DESC_TXCTRL_TXLAST |
393 			       DESC_TXCTRL_TXFIRST;
394 
395 	desc_p->txrx_status = DESC_TXSTS_OWNBYDMA;
396 #endif
397 
398 	/* Flush modified buffer descriptor */
399 	flush_dcache_range(desc_start, desc_end);
400 
401 	/* Test the wrap-around condition. */
402 	if (++desc_num >= CONFIG_TX_DESCR_NUM)
403 		desc_num = 0;
404 
405 	priv->tx_currdescnum = desc_num;
406 
407 	/* Start the transmission */
408 	writel(POLL_DATA, &dma_p->txpolldemand);
409 
410 	return 0;
411 }
412 
413 static int _dw_eth_recv(struct dw_eth_dev *priv, uchar **packetp)
414 {
415 	u32 status, desc_num = priv->rx_currdescnum;
416 	struct dmamacdescr *desc_p = &priv->rx_mac_descrtable[desc_num];
417 	int length = -EAGAIN;
418 	ulong desc_start = (ulong)desc_p;
419 	ulong desc_end = desc_start +
420 		roundup(sizeof(*desc_p), ARCH_DMA_MINALIGN);
421 	ulong data_start = desc_p->dmamac_addr;
422 	ulong data_end;
423 
424 	/* Invalidate entire buffer descriptor */
425 	invalidate_dcache_range(desc_start, desc_end);
426 
427 	status = desc_p->txrx_status;
428 
429 	/* Check  if the owner is the CPU */
430 	if (!(status & DESC_RXSTS_OWNBYDMA)) {
431 
432 		length = (status & DESC_RXSTS_FRMLENMSK) >>
433 			 DESC_RXSTS_FRMLENSHFT;
434 
435 		/* Invalidate received data */
436 		data_end = data_start + roundup(length, ARCH_DMA_MINALIGN);
437 		invalidate_dcache_range(data_start, data_end);
438 		*packetp = (uchar *)(ulong)desc_p->dmamac_addr;
439 	}
440 
441 	return length;
442 }
443 
444 static int _dw_free_pkt(struct dw_eth_dev *priv)
445 {
446 	u32 desc_num = priv->rx_currdescnum;
447 	struct dmamacdescr *desc_p = &priv->rx_mac_descrtable[desc_num];
448 	ulong desc_start = (ulong)desc_p;
449 	ulong desc_end = desc_start +
450 		roundup(sizeof(*desc_p), ARCH_DMA_MINALIGN);
451 
452 	/*
453 	 * Make the current descriptor valid again and go to
454 	 * the next one
455 	 */
456 	desc_p->txrx_status |= DESC_RXSTS_OWNBYDMA;
457 
458 	/* Flush only status field - others weren't changed */
459 	flush_dcache_range(desc_start, desc_end);
460 
461 	/* Test the wrap-around condition. */
462 	if (++desc_num >= CONFIG_RX_DESCR_NUM)
463 		desc_num = 0;
464 	priv->rx_currdescnum = desc_num;
465 
466 	return 0;
467 }
468 
469 static int dw_phy_init(struct dw_eth_dev *priv, void *dev)
470 {
471 	struct phy_device *phydev;
472 	int mask = 0xffffffff, ret;
473 
474 #ifdef CONFIG_PHY_ADDR
475 	mask = 1 << CONFIG_PHY_ADDR;
476 #endif
477 
478 	phydev = phy_find_by_mask(priv->bus, mask, priv->interface);
479 	if (!phydev)
480 		return -ENODEV;
481 
482 	phy_connect_dev(phydev, dev);
483 
484 	phydev->supported &= PHY_GBIT_FEATURES;
485 	if (priv->max_speed) {
486 		ret = phy_set_supported(phydev, priv->max_speed);
487 		if (ret)
488 			return ret;
489 	}
490 	phydev->advertising = phydev->supported;
491 
492 	priv->phydev = phydev;
493 	phy_config(phydev);
494 
495 	return 0;
496 }
497 
498 #ifndef CONFIG_DM_ETH
499 static int dw_eth_init(struct eth_device *dev, bd_t *bis)
500 {
501 	int ret;
502 
503 	ret = designware_eth_init(dev->priv, dev->enetaddr);
504 	if (!ret)
505 		ret = designware_eth_enable(dev->priv);
506 
507 	return ret;
508 }
509 
510 static int dw_eth_send(struct eth_device *dev, void *packet, int length)
511 {
512 	return _dw_eth_send(dev->priv, packet, length);
513 }
514 
515 static int dw_eth_recv(struct eth_device *dev)
516 {
517 	uchar *packet;
518 	int length;
519 
520 	length = _dw_eth_recv(dev->priv, &packet);
521 	if (length == -EAGAIN)
522 		return 0;
523 	net_process_received_packet(packet, length);
524 
525 	_dw_free_pkt(dev->priv);
526 
527 	return 0;
528 }
529 
530 static void dw_eth_halt(struct eth_device *dev)
531 {
532 	return _dw_eth_halt(dev->priv);
533 }
534 
535 static int dw_write_hwaddr(struct eth_device *dev)
536 {
537 	return _dw_write_hwaddr(dev->priv, dev->enetaddr);
538 }
539 
540 int designware_initialize(ulong base_addr, u32 interface)
541 {
542 	struct eth_device *dev;
543 	struct dw_eth_dev *priv;
544 
545 	dev = (struct eth_device *) malloc(sizeof(struct eth_device));
546 	if (!dev)
547 		return -ENOMEM;
548 
549 	/*
550 	 * Since the priv structure contains the descriptors which need a strict
551 	 * buswidth alignment, memalign is used to allocate memory
552 	 */
553 	priv = (struct dw_eth_dev *) memalign(ARCH_DMA_MINALIGN,
554 					      sizeof(struct dw_eth_dev));
555 	if (!priv) {
556 		free(dev);
557 		return -ENOMEM;
558 	}
559 
560 	if ((phys_addr_t)priv + sizeof(*priv) > (1ULL << 32)) {
561 		printf("designware: buffers are outside DMA memory\n");
562 		return -EINVAL;
563 	}
564 
565 	memset(dev, 0, sizeof(struct eth_device));
566 	memset(priv, 0, sizeof(struct dw_eth_dev));
567 
568 	sprintf(dev->name, "dwmac.%lx", base_addr);
569 	dev->iobase = (int)base_addr;
570 	dev->priv = priv;
571 
572 	priv->dev = dev;
573 	priv->mac_regs_p = (struct eth_mac_regs *)base_addr;
574 	priv->dma_regs_p = (struct eth_dma_regs *)(base_addr +
575 			DW_DMA_BASE_OFFSET);
576 
577 	dev->init = dw_eth_init;
578 	dev->send = dw_eth_send;
579 	dev->recv = dw_eth_recv;
580 	dev->halt = dw_eth_halt;
581 	dev->write_hwaddr = dw_write_hwaddr;
582 
583 	eth_register(dev);
584 
585 	priv->interface = interface;
586 
587 	dw_mdio_init(dev->name, priv->mac_regs_p);
588 	priv->bus = miiphy_get_dev_by_name(dev->name);
589 
590 	return dw_phy_init(priv, dev);
591 }
592 #endif
593 
594 #ifdef CONFIG_DM_ETH
595 static int designware_eth_start(struct udevice *dev)
596 {
597 	struct eth_pdata *pdata = dev_get_platdata(dev);
598 	struct dw_eth_dev *priv = dev_get_priv(dev);
599 	int ret;
600 
601 	ret = designware_eth_init(priv, pdata->enetaddr);
602 	if (ret)
603 		return ret;
604 	ret = designware_eth_enable(priv);
605 	if (ret)
606 		return ret;
607 
608 	return 0;
609 }
610 
611 int designware_eth_send(struct udevice *dev, void *packet, int length)
612 {
613 	struct dw_eth_dev *priv = dev_get_priv(dev);
614 
615 	return _dw_eth_send(priv, packet, length);
616 }
617 
618 int designware_eth_recv(struct udevice *dev, int flags, uchar **packetp)
619 {
620 	struct dw_eth_dev *priv = dev_get_priv(dev);
621 
622 	return _dw_eth_recv(priv, packetp);
623 }
624 
625 int designware_eth_free_pkt(struct udevice *dev, uchar *packet, int length)
626 {
627 	struct dw_eth_dev *priv = dev_get_priv(dev);
628 
629 	return _dw_free_pkt(priv);
630 }
631 
632 void designware_eth_stop(struct udevice *dev)
633 {
634 	struct dw_eth_dev *priv = dev_get_priv(dev);
635 
636 	return _dw_eth_halt(priv);
637 }
638 
639 int designware_eth_write_hwaddr(struct udevice *dev)
640 {
641 	struct eth_pdata *pdata = dev_get_platdata(dev);
642 	struct dw_eth_dev *priv = dev_get_priv(dev);
643 
644 	return _dw_write_hwaddr(priv, pdata->enetaddr);
645 }
646 
647 static int designware_eth_bind(struct udevice *dev)
648 {
649 #ifdef CONFIG_DM_PCI
650 	static int num_cards;
651 	char name[20];
652 
653 	/* Create a unique device name for PCI type devices */
654 	if (device_is_on_pci_bus(dev)) {
655 		sprintf(name, "eth_designware#%u", num_cards++);
656 		device_set_name(dev, name);
657 	}
658 #endif
659 
660 	return 0;
661 }
662 
663 int designware_eth_probe(struct udevice *dev)
664 {
665 	struct eth_pdata *pdata = dev_get_platdata(dev);
666 	struct dw_eth_dev *priv = dev_get_priv(dev);
667 	u32 iobase = pdata->iobase;
668 	ulong ioaddr;
669 	int ret;
670 #ifdef CONFIG_CLK
671 	int i, err, clock_nb;
672 
673 	priv->clock_count = 0;
674 	clock_nb = dev_count_phandle_with_args(dev, "clocks", "#clock-cells");
675 	if (clock_nb > 0) {
676 		priv->clocks = devm_kcalloc(dev, clock_nb, sizeof(struct clk),
677 					    GFP_KERNEL);
678 		if (!priv->clocks)
679 			return -ENOMEM;
680 
681 		for (i = 0; i < clock_nb; i++) {
682 			err = clk_get_by_index(dev, i, &priv->clocks[i]);
683 			if (err < 0)
684 				break;
685 
686 			err = clk_enable(&priv->clocks[i]);
687 			if (err) {
688 				pr_err("failed to enable clock %d\n", i);
689 				clk_free(&priv->clocks[i]);
690 				goto clk_err;
691 			}
692 			priv->clock_count++;
693 		}
694 	} else if (clock_nb != -ENOENT) {
695 		pr_err("failed to get clock phandle(%d)\n", clock_nb);
696 		return clock_nb;
697 	}
698 #endif
699 
700 #if defined(CONFIG_DM_REGULATOR)
701 	struct udevice *phy_supply;
702 
703 	ret = device_get_supply_regulator(dev, "phy-supply",
704 					  &phy_supply);
705 	if (ret) {
706 		debug("%s: No phy supply\n", dev->name);
707 	} else {
708 		ret = regulator_set_enable(phy_supply, true);
709 		if (ret) {
710 			puts("Error enabling phy supply\n");
711 			return ret;
712 		}
713 	}
714 #endif
715 
716 #ifdef CONFIG_DM_PCI
717 	/*
718 	 * If we are on PCI bus, either directly attached to a PCI root port,
719 	 * or via a PCI bridge, fill in platdata before we probe the hardware.
720 	 */
721 	if (device_is_on_pci_bus(dev)) {
722 		dm_pci_read_config32(dev, PCI_BASE_ADDRESS_0, &iobase);
723 		iobase &= PCI_BASE_ADDRESS_MEM_MASK;
724 		iobase = dm_pci_mem_to_phys(dev, iobase);
725 
726 		pdata->iobase = iobase;
727 		pdata->phy_interface = PHY_INTERFACE_MODE_RMII;
728 	}
729 #endif
730 
731 	debug("%s, iobase=%x, priv=%p\n", __func__, iobase, priv);
732 	ioaddr = iobase;
733 	priv->mac_regs_p = (struct eth_mac_regs *)ioaddr;
734 	priv->dma_regs_p = (struct eth_dma_regs *)(ioaddr + DW_DMA_BASE_OFFSET);
735 	priv->interface = pdata->phy_interface;
736 	priv->max_speed = pdata->max_speed;
737 
738 	dw_mdio_init(dev->name, dev);
739 	priv->bus = miiphy_get_dev_by_name(dev->name);
740 
741 	ret = dw_phy_init(priv, dev);
742 	debug("%s, ret=%d\n", __func__, ret);
743 
744 	return ret;
745 
746 #ifdef CONFIG_CLK
747 clk_err:
748 	ret = clk_release_all(priv->clocks, priv->clock_count);
749 	if (ret)
750 		pr_err("failed to disable all clocks\n");
751 
752 	return err;
753 #endif
754 }
755 
756 static int designware_eth_remove(struct udevice *dev)
757 {
758 	struct dw_eth_dev *priv = dev_get_priv(dev);
759 
760 	free(priv->phydev);
761 	mdio_unregister(priv->bus);
762 	mdio_free(priv->bus);
763 
764 #ifdef CONFIG_CLK
765 	return clk_release_all(priv->clocks, priv->clock_count);
766 #else
767 	return 0;
768 #endif
769 }
770 
771 const struct eth_ops designware_eth_ops = {
772 	.start			= designware_eth_start,
773 	.send			= designware_eth_send,
774 	.recv			= designware_eth_recv,
775 	.free_pkt		= designware_eth_free_pkt,
776 	.stop			= designware_eth_stop,
777 	.write_hwaddr		= designware_eth_write_hwaddr,
778 };
779 
780 int designware_eth_ofdata_to_platdata(struct udevice *dev)
781 {
782 	struct dw_eth_pdata *dw_pdata = dev_get_platdata(dev);
783 #ifdef CONFIG_DM_GPIO
784 	struct dw_eth_dev *priv = dev_get_priv(dev);
785 #endif
786 	struct eth_pdata *pdata = &dw_pdata->eth_pdata;
787 	const char *phy_mode;
788 #ifdef CONFIG_DM_GPIO
789 	int reset_flags = GPIOD_IS_OUT;
790 #endif
791 	int ret = 0;
792 
793 	pdata->iobase = dev_read_addr(dev);
794 	pdata->phy_interface = -1;
795 	phy_mode = dev_read_string(dev, "phy-mode");
796 	if (phy_mode)
797 		pdata->phy_interface = phy_get_interface_by_name(phy_mode);
798 	if (pdata->phy_interface == -1) {
799 		debug("%s: Invalid PHY interface '%s'\n", __func__, phy_mode);
800 		return -EINVAL;
801 	}
802 
803 	pdata->max_speed = dev_read_u32_default(dev, "max-speed", 0);
804 
805 #ifdef CONFIG_DM_GPIO
806 	if (dev_read_bool(dev, "snps,reset-active-low"))
807 		reset_flags |= GPIOD_ACTIVE_LOW;
808 
809 	ret = gpio_request_by_name(dev, "snps,reset-gpio", 0,
810 		&priv->reset_gpio, reset_flags);
811 	if (ret == 0) {
812 		ret = dev_read_u32_array(dev, "snps,reset-delays-us",
813 					 dw_pdata->reset_delays, 3);
814 	} else if (ret == -ENOENT) {
815 		ret = 0;
816 	}
817 #endif
818 
819 	return ret;
820 }
821 
822 static const struct udevice_id designware_eth_ids[] = {
823 	{ .compatible = "allwinner,sun7i-a20-gmac" },
824 	{ .compatible = "altr,socfpga-stmmac" },
825 	{ .compatible = "amlogic,meson6-dwmac" },
826 	{ .compatible = "amlogic,meson-gx-dwmac" },
827 	{ .compatible = "st,stm32-dwmac" },
828 	{ }
829 };
830 
831 U_BOOT_DRIVER(eth_designware) = {
832 	.name	= "eth_designware",
833 	.id	= UCLASS_ETH,
834 	.of_match = designware_eth_ids,
835 	.ofdata_to_platdata = designware_eth_ofdata_to_platdata,
836 	.bind	= designware_eth_bind,
837 	.probe	= designware_eth_probe,
838 	.remove	= designware_eth_remove,
839 	.ops	= &designware_eth_ops,
840 	.priv_auto_alloc_size = sizeof(struct dw_eth_dev),
841 	.platdata_auto_alloc_size = sizeof(struct dw_eth_pdata),
842 	.flags = DM_FLAG_ALLOC_PRIV_DMA,
843 };
844 
845 static struct pci_device_id supported[] = {
846 	{ PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_QRK_EMAC) },
847 	{ }
848 };
849 
850 U_BOOT_PCI_DEVICE(eth_designware, supported);
851 #endif
852