1 #ifndef CS8900_H 2 #define CS8900_H 3 /* 4 * Cirrus Logic CS8900A Ethernet 5 * 6 * (C) 2009 Ben Warren , biggerbadderben@gmail.com 7 * Converted to use CONFIG_NET_MULTI API 8 * 9 * (C) Copyright 2002 10 * Sysgo Real-Time Solutions, GmbH <www.elinos.com> 11 * Marius Groeger <mgroeger@sysgo.de> 12 * 13 * Copyright (C) 1999 Ben Williamson <benw@pobox.com> 14 * 15 * This program is loaded into SRAM in bootstrap mode, where it waits 16 * for commands on UART1 to read and write memory, jump to code etc. 17 * A design goal for this program is to be entirely independent of the 18 * target board. Anything with a CL-PS7111 or EP7211 should be able to run 19 * this code in bootstrap mode. All the board specifics can be handled on 20 * the host. 21 * 22 * SPDX-License-Identifier: GPL-2.0+ 23 */ 24 25 #include <asm/types.h> 26 #include <config.h> 27 28 #define CS8900_DRIVERNAME "CS8900" 29 /* although the registers are 16 bit, they are 32-bit aligned on the 30 EDB7111. so we have to read them as 32-bit registers and ignore the 31 upper 16-bits. i'm not sure if this holds for the EDB7211. */ 32 33 #ifdef CONFIG_CS8900_BUS16 34 /* 16 bit aligned registers, 16 bit wide */ 35 #define CS8900_REG u16 36 #elif defined(CONFIG_CS8900_BUS32) 37 /* 32 bit aligned registers, 16 bit wide (we ignore upper 16 bits) */ 38 #define CS8900_REG u32 39 #else 40 #error unknown bussize ... 41 #endif 42 43 struct cs8900_regs { 44 CS8900_REG rtdata; 45 CS8900_REG pad0; 46 CS8900_REG txcmd; 47 CS8900_REG txlen; 48 CS8900_REG isq; 49 CS8900_REG pptr; 50 CS8900_REG pdata; 51 }; 52 53 struct cs8900_priv { 54 struct cs8900_regs *regs; 55 }; 56 57 #define ISQ_RxEvent 0x04 58 #define ISQ_TxEvent 0x08 59 #define ISQ_BufEvent 0x0C 60 #define ISQ_RxMissEvent 0x10 61 #define ISQ_TxColEvent 0x12 62 #define ISQ_EventMask 0x3F 63 64 /* packet page register offsets */ 65 66 /* bus interface registers */ 67 #define PP_ChipID 0x0000 /* Chip identifier - must be 0x630E */ 68 #define PP_ChipRev 0x0002 /* Chip revision, model codes */ 69 70 #define PP_IntReg 0x0022 /* Interrupt configuration */ 71 #define PP_IntReg_IRQ0 0x0000 /* Use INTR0 pin */ 72 #define PP_IntReg_IRQ1 0x0001 /* Use INTR1 pin */ 73 #define PP_IntReg_IRQ2 0x0002 /* Use INTR2 pin */ 74 #define PP_IntReg_IRQ3 0x0003 /* Use INTR3 pin */ 75 76 /* status and control registers */ 77 78 #define PP_RxCFG 0x0102 /* Receiver configuration */ 79 #define PP_RxCFG_Skip1 0x0040 /* Skip (i.e. discard) current frame */ 80 #define PP_RxCFG_Stream 0x0080 /* Enable streaming mode */ 81 #define PP_RxCFG_RxOK 0x0100 /* RxOK interrupt enable */ 82 #define PP_RxCFG_RxDMAonly 0x0200 /* Use RxDMA for all frames */ 83 #define PP_RxCFG_AutoRxDMA 0x0400 /* Select RxDMA automatically */ 84 #define PP_RxCFG_BufferCRC 0x0800 /* Include CRC characters in frame */ 85 #define PP_RxCFG_CRC 0x1000 /* Enable interrupt on CRC error */ 86 #define PP_RxCFG_RUNT 0x2000 /* Enable interrupt on RUNT frames */ 87 #define PP_RxCFG_EXTRA 0x4000 /* Enable interrupt on frames with extra data */ 88 89 #define PP_RxCTL 0x0104 /* Receiver control */ 90 #define PP_RxCTL_IAHash 0x0040 /* Accept frames that match hash */ 91 #define PP_RxCTL_Promiscuous 0x0080 /* Accept any frame */ 92 #define PP_RxCTL_RxOK 0x0100 /* Accept well formed frames */ 93 #define PP_RxCTL_Multicast 0x0200 /* Accept multicast frames */ 94 #define PP_RxCTL_IA 0x0400 /* Accept frame that matches IA */ 95 #define PP_RxCTL_Broadcast 0x0800 /* Accept broadcast frames */ 96 #define PP_RxCTL_CRC 0x1000 /* Accept frames with bad CRC */ 97 #define PP_RxCTL_RUNT 0x2000 /* Accept runt frames */ 98 #define PP_RxCTL_EXTRA 0x4000 /* Accept frames that are too long */ 99 100 #define PP_TxCFG 0x0106 /* Transmit configuration */ 101 #define PP_TxCFG_CRS 0x0040 /* Enable interrupt on loss of carrier */ 102 #define PP_TxCFG_SQE 0x0080 /* Enable interrupt on Signal Quality Error */ 103 #define PP_TxCFG_TxOK 0x0100 /* Enable interrupt on successful xmits */ 104 #define PP_TxCFG_Late 0x0200 /* Enable interrupt on "out of window" */ 105 #define PP_TxCFG_Jabber 0x0400 /* Enable interrupt on jabber detect */ 106 #define PP_TxCFG_Collision 0x0800 /* Enable interrupt if collision */ 107 #define PP_TxCFG_16Collisions 0x8000 /* Enable interrupt if > 16 collisions */ 108 109 #define PP_TxCmd 0x0108 /* Transmit command status */ 110 #define PP_TxCmd_TxStart_5 0x0000 /* Start after 5 bytes in buffer */ 111 #define PP_TxCmd_TxStart_381 0x0040 /* Start after 381 bytes in buffer */ 112 #define PP_TxCmd_TxStart_1021 0x0080 /* Start after 1021 bytes in buffer */ 113 #define PP_TxCmd_TxStart_Full 0x00C0 /* Start after all bytes loaded */ 114 #define PP_TxCmd_Force 0x0100 /* Discard any pending packets */ 115 #define PP_TxCmd_OneCollision 0x0200 /* Abort after a single collision */ 116 #define PP_TxCmd_NoCRC 0x1000 /* Do not add CRC */ 117 #define PP_TxCmd_NoPad 0x2000 /* Do not pad short packets */ 118 119 #define PP_BufCFG 0x010A /* Buffer configuration */ 120 #define PP_BufCFG_SWI 0x0040 /* Force interrupt via software */ 121 #define PP_BufCFG_RxDMA 0x0080 /* Enable interrupt on Rx DMA */ 122 #define PP_BufCFG_TxRDY 0x0100 /* Enable interrupt when ready for Tx */ 123 #define PP_BufCFG_TxUE 0x0200 /* Enable interrupt in Tx underrun */ 124 #define PP_BufCFG_RxMiss 0x0400 /* Enable interrupt on missed Rx packets */ 125 #define PP_BufCFG_Rx128 0x0800 /* Enable Rx interrupt after 128 bytes */ 126 #define PP_BufCFG_TxCol 0x1000 /* Enable int on Tx collision ctr overflow */ 127 #define PP_BufCFG_Miss 0x2000 /* Enable int on Rx miss ctr overflow */ 128 #define PP_BufCFG_RxDest 0x8000 /* Enable int on Rx dest addr match */ 129 130 #define PP_LineCTL 0x0112 /* Line control */ 131 #define PP_LineCTL_Rx 0x0040 /* Enable receiver */ 132 #define PP_LineCTL_Tx 0x0080 /* Enable transmitter */ 133 #define PP_LineCTL_AUIonly 0x0100 /* AUI interface only */ 134 #define PP_LineCTL_AutoAUI10BT 0x0200 /* Autodetect AUI or 10BaseT interface */ 135 #define PP_LineCTL_ModBackoffE 0x0800 /* Enable modified backoff algorithm */ 136 #define PP_LineCTL_PolarityDis 0x1000 /* Disable Rx polarity autodetect */ 137 #define PP_LineCTL_2partDefDis 0x2000 /* Disable two-part defferal */ 138 #define PP_LineCTL_LoRxSquelch 0x4000 /* Reduce receiver squelch threshold */ 139 140 #define PP_SelfCTL 0x0114 /* Chip self control */ 141 #define PP_SelfCTL_Reset 0x0040 /* Self-clearing reset */ 142 #define PP_SelfCTL_SWSuspend 0x0100 /* Initiate suspend mode */ 143 #define PP_SelfCTL_HWSleepE 0x0200 /* Enable SLEEP input */ 144 #define PP_SelfCTL_HWStandbyE 0x0400 /* Enable standby mode */ 145 #define PP_SelfCTL_HC0E 0x1000 /* use HCB0 for LINK LED */ 146 #define PP_SelfCTL_HC1E 0x2000 /* use HCB1 for BSTATUS LED */ 147 #define PP_SelfCTL_HCB0 0x4000 /* control LINK LED if HC0E set */ 148 #define PP_SelfCTL_HCB1 0x8000 /* control BSTATUS LED if HC1E set */ 149 150 #define PP_BusCTL 0x0116 /* Bus control */ 151 #define PP_BusCTL_ResetRxDMA 0x0040 /* Reset RxDMA pointer */ 152 #define PP_BusCTL_DMAextend 0x0100 /* Extend DMA cycle */ 153 #define PP_BusCTL_UseSA 0x0200 /* Assert MEMCS16 on address decode */ 154 #define PP_BusCTL_MemoryE 0x0400 /* Enable memory mode */ 155 #define PP_BusCTL_DMAburst 0x0800 /* Limit DMA access burst */ 156 #define PP_BusCTL_IOCHRDYE 0x1000 /* Set IOCHRDY high impedence */ 157 #define PP_BusCTL_RxDMAsize 0x2000 /* Set DMA buffer size 64KB */ 158 #define PP_BusCTL_EnableIRQ 0x8000 /* Generate interrupt on interrupt event */ 159 160 #define PP_TestCTL 0x0118 /* Test control */ 161 #define PP_TestCTL_DisableLT 0x0080 /* Disable link status */ 162 #define PP_TestCTL_ENDECloop 0x0200 /* Internal loopback */ 163 #define PP_TestCTL_AUIloop 0x0400 /* AUI loopback */ 164 #define PP_TestCTL_DisBackoff 0x0800 /* Disable backoff algorithm */ 165 #define PP_TestCTL_FDX 0x4000 /* Enable full duplex mode */ 166 167 #define PP_ISQ 0x0120 /* Interrupt Status Queue */ 168 169 #define PP_RER 0x0124 /* Receive event */ 170 #define PP_RER_IAHash 0x0040 /* Frame hash match */ 171 #define PP_RER_Dribble 0x0080 /* Frame had 1-7 extra bits after last byte */ 172 #define PP_RER_RxOK 0x0100 /* Frame received with no errors */ 173 #define PP_RER_Hashed 0x0200 /* Frame address hashed OK */ 174 #define PP_RER_IA 0x0400 /* Frame address matched IA */ 175 #define PP_RER_Broadcast 0x0800 /* Broadcast frame */ 176 #define PP_RER_CRC 0x1000 /* Frame had CRC error */ 177 #define PP_RER_RUNT 0x2000 /* Runt frame */ 178 #define PP_RER_EXTRA 0x4000 /* Frame was too long */ 179 180 #define PP_TER 0x0128 /* Transmit event */ 181 #define PP_TER_CRS 0x0040 /* Carrier lost */ 182 #define PP_TER_SQE 0x0080 /* Signal Quality Error */ 183 #define PP_TER_TxOK 0x0100 /* Packet sent without error */ 184 #define PP_TER_Late 0x0200 /* Out of window */ 185 #define PP_TER_Jabber 0x0400 /* Stuck transmit? */ 186 #define PP_TER_NumCollisions 0x7800 /* Number of collisions */ 187 #define PP_TER_16Collisions 0x8000 /* > 16 collisions */ 188 189 #define PP_BER 0x012C /* Buffer event */ 190 #define PP_BER_SWint 0x0040 /* Software interrupt */ 191 #define PP_BER_RxDMAFrame 0x0080 /* Received framed DMAed */ 192 #define PP_BER_Rdy4Tx 0x0100 /* Ready for transmission */ 193 #define PP_BER_TxUnderrun 0x0200 /* Transmit underrun */ 194 #define PP_BER_RxMiss 0x0400 /* Received frame missed */ 195 #define PP_BER_Rx128 0x0800 /* 128 bytes received */ 196 #define PP_BER_RxDest 0x8000 /* Received framed passed address filter */ 197 198 #define PP_RxMiss 0x0130 /* Receiver miss counter */ 199 200 #define PP_TxCol 0x0132 /* Transmit collision counter */ 201 202 #define PP_LineSTAT 0x0134 /* Line status */ 203 #define PP_LineSTAT_LinkOK 0x0080 /* Line is connected and working */ 204 #define PP_LineSTAT_AUI 0x0100 /* Connected via AUI */ 205 #define PP_LineSTAT_10BT 0x0200 /* Connected via twisted pair */ 206 #define PP_LineSTAT_Polarity 0x1000 /* Line polarity OK (10BT only) */ 207 #define PP_LineSTAT_CRS 0x4000 /* Frame being received */ 208 209 #define PP_SelfSTAT 0x0136 /* Chip self status */ 210 #define PP_SelfSTAT_33VActive 0x0040 /* supply voltage is 3.3V */ 211 #define PP_SelfSTAT_InitD 0x0080 /* Chip initialization complete */ 212 #define PP_SelfSTAT_SIBSY 0x0100 /* EEPROM is busy */ 213 #define PP_SelfSTAT_EEPROM 0x0200 /* EEPROM present */ 214 #define PP_SelfSTAT_EEPROM_OK 0x0400 /* EEPROM checks out */ 215 #define PP_SelfSTAT_ELPresent 0x0800 /* External address latch logic available */ 216 #define PP_SelfSTAT_EEsize 0x1000 /* Size of EEPROM */ 217 218 #define PP_BusSTAT 0x0138 /* Bus status */ 219 #define PP_BusSTAT_TxBid 0x0080 /* Tx error */ 220 #define PP_BusSTAT_TxRDY 0x0100 /* Ready for Tx data */ 221 222 #define PP_TDR 0x013C /* AUI Time Domain Reflectometer */ 223 224 /* initiate transmit registers */ 225 226 #define PP_TxCommand 0x0144 /* Tx Command */ 227 #define PP_TxLength 0x0146 /* Tx Length */ 228 229 230 /* address filter registers */ 231 232 #define PP_LAF 0x0150 /* Logical address filter (6 bytes) */ 233 #define PP_IA 0x0158 /* Individual address (MAC) */ 234 235 /* EEPROM Kram */ 236 #define SI_BUSY 0x0100 237 #define PP_EECMD 0x0040 /* NVR Interface Command register */ 238 #define PP_EEData 0x0042 /* NVR Interface Data Register */ 239 #define EEPROM_WRITE_EN 0x00F0 240 #define EEPROM_WRITE_DIS 0x0000 241 #define EEPROM_WRITE_CMD 0x0100 242 #define EEPROM_READ_CMD 0x0200 243 #define EEPROM_ERASE_CMD 0x0300 244 245 /* Exported functions */ 246 int cs8900_e2prom_read(struct eth_device *dev, uchar, ushort *); 247 int cs8900_e2prom_write(struct eth_device *dev, uchar, ushort); 248 249 #endif /* CS8900_H */ 250