1 /* 2 * Atmel DataFlash probing 3 * 4 * Copyright (C) 2004-2009, 2015 Freescale Semiconductor, Inc. 5 * Haikun Wang (haikun.wang@freescale.com) 6 * 7 * SPDX-License-Identifier: GPL-2.0+ 8 */ 9 10 #include <common.h> 11 #include <dm.h> 12 #include <errno.h> 13 #include <fdtdec.h> 14 #include <spi.h> 15 #include <spi_flash.h> 16 #include <div64.h> 17 #include <linux/err.h> 18 #include <linux/math64.h> 19 20 #include "sf_internal.h" 21 22 /* reads can bypass the buffers */ 23 #define OP_READ_CONTINUOUS 0xE8 24 #define OP_READ_PAGE 0xD2 25 26 /* group B requests can run even while status reports "busy" */ 27 #define OP_READ_STATUS 0xD7 /* group B */ 28 29 /* move data between host and buffer */ 30 #define OP_READ_BUFFER1 0xD4 /* group B */ 31 #define OP_READ_BUFFER2 0xD6 /* group B */ 32 #define OP_WRITE_BUFFER1 0x84 /* group B */ 33 #define OP_WRITE_BUFFER2 0x87 /* group B */ 34 35 /* erasing flash */ 36 #define OP_ERASE_PAGE 0x81 37 #define OP_ERASE_BLOCK 0x50 38 39 /* move data between buffer and flash */ 40 #define OP_TRANSFER_BUF1 0x53 41 #define OP_TRANSFER_BUF2 0x55 42 #define OP_MREAD_BUFFER1 0xD4 43 #define OP_MREAD_BUFFER2 0xD6 44 #define OP_MWERASE_BUFFER1 0x83 45 #define OP_MWERASE_BUFFER2 0x86 46 #define OP_MWRITE_BUFFER1 0x88 /* sector must be pre-erased */ 47 #define OP_MWRITE_BUFFER2 0x89 /* sector must be pre-erased */ 48 49 /* write to buffer, then write-erase to flash */ 50 #define OP_PROGRAM_VIA_BUF1 0x82 51 #define OP_PROGRAM_VIA_BUF2 0x85 52 53 /* compare buffer to flash */ 54 #define OP_COMPARE_BUF1 0x60 55 #define OP_COMPARE_BUF2 0x61 56 57 /* read flash to buffer, then write-erase to flash */ 58 #define OP_REWRITE_VIA_BUF1 0x58 59 #define OP_REWRITE_VIA_BUF2 0x59 60 61 /* 62 * newer chips report JEDEC manufacturer and device IDs; chip 63 * serial number and OTP bits; and per-sector writeprotect. 64 */ 65 #define OP_READ_ID 0x9F 66 #define OP_READ_SECURITY 0x77 67 #define OP_WRITE_SECURITY_REVC 0x9A 68 #define OP_WRITE_SECURITY 0x9B /* revision D */ 69 70 struct dataflash { 71 uint8_t command[16]; 72 unsigned short page_offset; /* offset in flash address */ 73 }; 74 75 /* Return the status of the DataFlash device */ 76 static inline int dataflash_status(struct spi_slave *spi) 77 { 78 int ret; 79 u8 status; 80 /* 81 * NOTE: at45db321c over 25 MHz wants to write 82 * a dummy byte after the opcode... 83 */ 84 ret = spi_flash_cmd(spi, OP_READ_STATUS, &status, 1); 85 return ret ? -EIO : status; 86 } 87 88 /* 89 * Poll the DataFlash device until it is READY. 90 * This usually takes 5-20 msec or so; more for sector erase. 91 * ready: return > 0 92 */ 93 static int dataflash_waitready(struct spi_slave *spi) 94 { 95 int status; 96 int timeout = 2 * CONFIG_SYS_HZ; 97 int timebase; 98 99 timebase = get_timer(0); 100 do { 101 status = dataflash_status(spi); 102 if (status < 0) 103 status = 0; 104 105 if (status & (1 << 7)) /* RDY/nBSY */ 106 return status; 107 108 mdelay(3); 109 } while (get_timer(timebase) < timeout); 110 111 return -ETIME; 112 } 113 114 /* Erase pages of flash */ 115 static int spi_dataflash_erase(struct udevice *dev, u32 offset, size_t len) 116 { 117 struct dataflash *dataflash; 118 struct spi_flash *spi_flash; 119 struct spi_slave *spi; 120 unsigned blocksize; 121 uint8_t *command; 122 uint32_t rem; 123 int status; 124 125 dataflash = dev_get_priv(dev); 126 spi_flash = dev_get_uclass_priv(dev); 127 spi = spi_flash->spi; 128 129 blocksize = spi_flash->page_size << 3; 130 131 memset(dataflash->command, 0 , sizeof(dataflash->command)); 132 command = dataflash->command; 133 134 debug("%s: erase addr=0x%x len 0x%x\n", dev->name, offset, len); 135 136 div_u64_rem(len, spi_flash->page_size, &rem); 137 if (rem) { 138 printf("%s: len(0x%x) isn't the multiple of page size(0x%x)\n", 139 dev->name, len, spi_flash->page_size); 140 return -EINVAL; 141 } 142 div_u64_rem(offset, spi_flash->page_size, &rem); 143 if (rem) { 144 printf("%s: offset(0x%x) isn't the multiple of page size(0x%x)\n", 145 dev->name, offset, spi_flash->page_size); 146 return -EINVAL; 147 } 148 149 status = spi_claim_bus(spi); 150 if (status) { 151 debug("dataflash: unable to claim SPI bus\n"); 152 return status; 153 } 154 155 while (len > 0) { 156 unsigned int pageaddr; 157 int do_block; 158 /* 159 * Calculate flash page address; use block erase (for speed) if 160 * we're at a block boundary and need to erase the whole block. 161 */ 162 pageaddr = div_u64(offset, spi_flash->page_size); 163 do_block = (pageaddr & 0x7) == 0 && len >= blocksize; 164 pageaddr = pageaddr << dataflash->page_offset; 165 166 command[0] = do_block ? OP_ERASE_BLOCK : OP_ERASE_PAGE; 167 command[1] = (uint8_t)(pageaddr >> 16); 168 command[2] = (uint8_t)(pageaddr >> 8); 169 command[3] = 0; 170 171 debug("%s ERASE %s: (%x) %x %x %x [%d]\n", 172 dev->name, do_block ? "block" : "page", 173 command[0], command[1], command[2], command[3], 174 pageaddr); 175 176 status = spi_flash_cmd_write(spi, command, 4, NULL, 0); 177 if (status < 0) { 178 debug("%s: erase send command error!\n", dev->name); 179 return -EIO; 180 } 181 182 status = dataflash_waitready(spi); 183 if (status < 0) { 184 debug("%s: erase waitready error!\n", dev->name); 185 return status; 186 } 187 188 if (do_block) { 189 offset += blocksize; 190 len -= blocksize; 191 } else { 192 offset += spi_flash->page_size; 193 len -= spi_flash->page_size; 194 } 195 } 196 197 spi_release_bus(spi); 198 199 return 0; 200 } 201 202 /* 203 * Read from the DataFlash device. 204 * offset : Start offset in flash device 205 * len : Amount to read 206 * buf : Buffer containing the data 207 */ 208 static int spi_dataflash_read(struct udevice *dev, u32 offset, size_t len, 209 void *buf) 210 { 211 struct dataflash *dataflash; 212 struct spi_flash *spi_flash; 213 struct spi_slave *spi; 214 unsigned int addr; 215 uint8_t *command; 216 int status; 217 218 dataflash = dev_get_priv(dev); 219 spi_flash = dev_get_uclass_priv(dev); 220 spi = spi_flash->spi; 221 222 memset(dataflash->command, 0 , sizeof(dataflash->command)); 223 command = dataflash->command; 224 225 debug("%s: erase addr=0x%x len 0x%x\n", dev->name, offset, len); 226 debug("READ: (%x) %x %x %x\n", 227 command[0], command[1], command[2], command[3]); 228 229 /* Calculate flash page/byte address */ 230 addr = (((unsigned)offset / spi_flash->page_size) 231 << dataflash->page_offset) 232 + ((unsigned)offset % spi_flash->page_size); 233 234 status = spi_claim_bus(spi); 235 if (status) { 236 debug("dataflash: unable to claim SPI bus\n"); 237 return status; 238 } 239 240 /* 241 * Continuous read, max clock = f(car) which may be less than 242 * the peak rate available. Some chips support commands with 243 * fewer "don't care" bytes. Both buffers stay unchanged. 244 */ 245 command[0] = OP_READ_CONTINUOUS; 246 command[1] = (uint8_t)(addr >> 16); 247 command[2] = (uint8_t)(addr >> 8); 248 command[3] = (uint8_t)(addr >> 0); 249 250 /* plus 4 "don't care" bytes, command len: 4 + 4 "don't care" bytes */ 251 status = spi_flash_cmd_read(spi, command, 8, buf, len); 252 253 spi_release_bus(spi); 254 255 return status; 256 } 257 258 /* 259 * Write to the DataFlash device. 260 * offset : Start offset in flash device 261 * len : Amount to write 262 * buf : Buffer containing the data 263 */ 264 int spi_dataflash_write(struct udevice *dev, u32 offset, size_t len, 265 const void *buf) 266 { 267 struct dataflash *dataflash; 268 struct spi_flash *spi_flash; 269 struct spi_slave *spi; 270 uint8_t *command; 271 unsigned int pageaddr, addr, to, writelen; 272 size_t remaining = len; 273 u_char *writebuf = (u_char *)buf; 274 int status = -EINVAL; 275 276 dataflash = dev_get_priv(dev); 277 spi_flash = dev_get_uclass_priv(dev); 278 spi = spi_flash->spi; 279 280 memset(dataflash->command, 0 , sizeof(dataflash->command)); 281 command = dataflash->command; 282 283 debug("%s: write 0x%x..0x%x\n", dev->name, offset, (offset + len)); 284 285 pageaddr = ((unsigned)offset / spi_flash->page_size); 286 to = ((unsigned)offset % spi_flash->page_size); 287 if (to + len > spi_flash->page_size) 288 writelen = spi_flash->page_size - to; 289 else 290 writelen = len; 291 292 status = spi_claim_bus(spi); 293 if (status) { 294 debug("dataflash: unable to claim SPI bus\n"); 295 return status; 296 } 297 298 while (remaining > 0) { 299 debug("write @ %d:%d len=%d\n", pageaddr, to, writelen); 300 301 /* 302 * REVISIT: 303 * (a) each page in a sector must be rewritten at least 304 * once every 10K sibling erase/program operations. 305 * (b) for pages that are already erased, we could 306 * use WRITE+MWRITE not PROGRAM for ~30% speedup. 307 * (c) WRITE to buffer could be done while waiting for 308 * a previous MWRITE/MWERASE to complete ... 309 * (d) error handling here seems to be mostly missing. 310 * 311 * Two persistent bits per page, plus a per-sector counter, 312 * could support (a) and (b) ... we might consider using 313 * the second half of sector zero, which is just one block, 314 * to track that state. (On AT91, that sector should also 315 * support boot-from-DataFlash.) 316 */ 317 318 addr = pageaddr << dataflash->page_offset; 319 320 /* (1) Maybe transfer partial page to Buffer1 */ 321 if (writelen != spi_flash->page_size) { 322 command[0] = OP_TRANSFER_BUF1; 323 command[1] = (addr & 0x00FF0000) >> 16; 324 command[2] = (addr & 0x0000FF00) >> 8; 325 command[3] = 0; 326 327 debug("TRANSFER: (%x) %x %x %x\n", 328 command[0], command[1], command[2], command[3]); 329 330 status = spi_flash_cmd_write(spi, command, 4, NULL, 0); 331 if (status < 0) { 332 debug("%s: write(<pagesize) command error!\n", 333 dev->name); 334 return -EIO; 335 } 336 337 status = dataflash_waitready(spi); 338 if (status < 0) { 339 debug("%s: write(<pagesize) waitready error!\n", 340 dev->name); 341 return status; 342 } 343 } 344 345 /* (2) Program full page via Buffer1 */ 346 addr += to; 347 command[0] = OP_PROGRAM_VIA_BUF1; 348 command[1] = (addr & 0x00FF0000) >> 16; 349 command[2] = (addr & 0x0000FF00) >> 8; 350 command[3] = (addr & 0x000000FF); 351 352 debug("PROGRAM: (%x) %x %x %x\n", 353 command[0], command[1], command[2], command[3]); 354 355 status = spi_flash_cmd_write(spi, command, 356 4, writebuf, writelen); 357 if (status < 0) { 358 debug("%s: write send command error!\n", dev->name); 359 return -EIO; 360 } 361 362 status = dataflash_waitready(spi); 363 if (status < 0) { 364 debug("%s: write waitready error!\n", dev->name); 365 return status; 366 } 367 368 #ifdef CONFIG_SPI_DATAFLASH_WRITE_VERIFY 369 /* (3) Compare to Buffer1 */ 370 addr = pageaddr << dataflash->page_offset; 371 command[0] = OP_COMPARE_BUF1; 372 command[1] = (addr & 0x00FF0000) >> 16; 373 command[2] = (addr & 0x0000FF00) >> 8; 374 command[3] = 0; 375 376 debug("COMPARE: (%x) %x %x %x\n", 377 command[0], command[1], command[2], command[3]); 378 379 status = spi_flash_cmd_write(spi, command, 380 4, writebuf, writelen); 381 if (status < 0) { 382 debug("%s: write(compare) send command error!\n", 383 dev->name); 384 return -EIO; 385 } 386 387 status = dataflash_waitready(spi); 388 389 /* Check result of the compare operation */ 390 if (status & (1 << 6)) { 391 printf("dataflash: write compare page %u, err %d\n", 392 pageaddr, status); 393 remaining = 0; 394 status = -EIO; 395 break; 396 } else { 397 status = 0; 398 } 399 400 #endif /* CONFIG_SPI_DATAFLASH_WRITE_VERIFY */ 401 remaining = remaining - writelen; 402 pageaddr++; 403 to = 0; 404 writebuf += writelen; 405 406 if (remaining > spi_flash->page_size) 407 writelen = spi_flash->page_size; 408 else 409 writelen = remaining; 410 } 411 412 spi_release_bus(spi); 413 414 return 0; 415 } 416 417 static int add_dataflash(struct udevice *dev, char *name, int nr_pages, 418 int pagesize, int pageoffset, char revision) 419 { 420 struct spi_flash *spi_flash; 421 struct dataflash *dataflash; 422 423 dataflash = dev_get_priv(dev); 424 spi_flash = dev_get_uclass_priv(dev); 425 426 dataflash->page_offset = pageoffset; 427 428 spi_flash->name = name; 429 spi_flash->page_size = pagesize; 430 spi_flash->size = nr_pages * pagesize; 431 spi_flash->erase_size = pagesize; 432 433 #ifndef CONFIG_SPL_BUILD 434 printf("SPI DataFlash: Detected %s with page size ", spi_flash->name); 435 print_size(spi_flash->page_size, ", erase size "); 436 print_size(spi_flash->erase_size, ", total "); 437 print_size(spi_flash->size, ""); 438 printf(", revision %c", revision); 439 puts("\n"); 440 #endif 441 442 return 0; 443 } 444 445 struct flash_info { 446 char *name; 447 448 /* 449 * JEDEC id has a high byte of zero plus three data bytes: 450 * the manufacturer id, then a two byte device id. 451 */ 452 uint32_t jedec_id; 453 454 /* The size listed here is what works with OP_ERASE_PAGE. */ 455 unsigned nr_pages; 456 uint16_t pagesize; 457 uint16_t pageoffset; 458 459 uint16_t flags; 460 #define SUP_POW2PS 0x0002 /* supports 2^N byte pages */ 461 #define IS_POW2PS 0x0001 /* uses 2^N byte pages */ 462 }; 463 464 static struct flash_info dataflash_data[] = { 465 /* 466 * NOTE: chips with SUP_POW2PS (rev D and up) need two entries, 467 * one with IS_POW2PS and the other without. The entry with the 468 * non-2^N byte page size can't name exact chip revisions without 469 * losing backwards compatibility for cmdlinepart. 470 * 471 * Those two entries have different name spelling format in order to 472 * show their difference obviously. 473 * The upper case refer to the chip isn't in normal 2^N bytes page-size 474 * mode. 475 * The lower case refer to the chip is in normal 2^N bytes page-size 476 * mode. 477 * 478 * These newer chips also support 128-byte security registers (with 479 * 64 bytes one-time-programmable) and software write-protection. 480 */ 481 { "AT45DB011B", 0x1f2200, 512, 264, 9, SUP_POW2PS}, 482 { "at45db011d", 0x1f2200, 512, 256, 8, SUP_POW2PS | IS_POW2PS}, 483 484 { "AT45DB021B", 0x1f2300, 1024, 264, 9, SUP_POW2PS}, 485 { "at45db021d", 0x1f2300, 1024, 256, 8, SUP_POW2PS | IS_POW2PS}, 486 487 { "AT45DB041x", 0x1f2400, 2048, 264, 9, SUP_POW2PS}, 488 { "at45db041d", 0x1f2400, 2048, 256, 8, SUP_POW2PS | IS_POW2PS}, 489 490 { "AT45DB081B", 0x1f2500, 4096, 264, 9, SUP_POW2PS}, 491 { "at45db081d", 0x1f2500, 4096, 256, 8, SUP_POW2PS | IS_POW2PS}, 492 493 { "AT45DB161x", 0x1f2600, 4096, 528, 10, SUP_POW2PS}, 494 { "at45db161d", 0x1f2600, 4096, 512, 9, SUP_POW2PS | IS_POW2PS}, 495 496 { "AT45DB321x", 0x1f2700, 8192, 528, 10, 0}, /* rev C */ 497 498 { "AT45DB321x", 0x1f2701, 8192, 528, 10, SUP_POW2PS}, 499 { "at45db321d", 0x1f2701, 8192, 512, 9, SUP_POW2PS | IS_POW2PS}, 500 501 { "AT45DB642x", 0x1f2800, 8192, 1056, 11, SUP_POW2PS}, 502 { "at45db642d", 0x1f2800, 8192, 1024, 10, SUP_POW2PS | IS_POW2PS}, 503 }; 504 505 static struct flash_info *jedec_probe(struct spi_slave *spi) 506 { 507 int tmp; 508 uint8_t id[5]; 509 uint32_t jedec; 510 struct flash_info *info; 511 int status; 512 513 /* 514 * JEDEC also defines an optional "extended device information" 515 * string for after vendor-specific data, after the three bytes 516 * we use here. Supporting some chips might require using it. 517 * 518 * If the vendor ID isn't Atmel's (0x1f), assume this call failed. 519 * That's not an error; only rev C and newer chips handle it, and 520 * only Atmel sells these chips. 521 */ 522 tmp = spi_flash_cmd(spi, CMD_READ_ID, id, sizeof(id)); 523 if (tmp < 0) { 524 printf("dataflash: error %d reading JEDEC ID\n", tmp); 525 return ERR_PTR(tmp); 526 } 527 if (id[0] != 0x1f) 528 return NULL; 529 530 jedec = id[0]; 531 jedec = jedec << 8; 532 jedec |= id[1]; 533 jedec = jedec << 8; 534 jedec |= id[2]; 535 536 for (tmp = 0, info = dataflash_data; 537 tmp < ARRAY_SIZE(dataflash_data); 538 tmp++, info++) { 539 if (info->jedec_id == jedec) { 540 if (info->flags & SUP_POW2PS) { 541 status = dataflash_status(spi); 542 if (status < 0) { 543 debug("dataflash: status error %d\n", 544 status); 545 return NULL; 546 } 547 if (status & 0x1) { 548 if (info->flags & IS_POW2PS) 549 return info; 550 } else { 551 if (!(info->flags & IS_POW2PS)) 552 return info; 553 } 554 } else { 555 return info; 556 } 557 } 558 } 559 560 /* 561 * Treat other chips as errors ... we won't know the right page 562 * size (it might be binary) even when we can tell which density 563 * class is involved (legacy chip id scheme). 564 */ 565 printf("dataflash: JEDEC id %06x not handled\n", jedec); 566 return ERR_PTR(-ENODEV); 567 } 568 569 /* 570 * Detect and initialize DataFlash device, using JEDEC IDs on newer chips 571 * or else the ID code embedded in the status bits: 572 * 573 * Device Density ID code #Pages PageSize Offset 574 * AT45DB011B 1Mbit (128K) xx0011xx (0x0c) 512 264 9 575 * AT45DB021B 2Mbit (256K) xx0101xx (0x14) 1024 264 9 576 * AT45DB041B 4Mbit (512K) xx0111xx (0x1c) 2048 264 9 577 * AT45DB081B 8Mbit (1M) xx1001xx (0x24) 4096 264 9 578 * AT45DB0161B 16Mbit (2M) xx1011xx (0x2c) 4096 528 10 579 * AT45DB0321B 32Mbit (4M) xx1101xx (0x34) 8192 528 10 580 * AT45DB0642 64Mbit (8M) xx111xxx (0x3c) 8192 1056 11 581 * AT45DB1282 128Mbit (16M) xx0100xx (0x10) 16384 1056 11 582 */ 583 static int spi_dataflash_probe(struct udevice *dev) 584 { 585 struct spi_slave *spi = dev_get_parent_priv(dev); 586 struct spi_flash *spi_flash; 587 struct flash_info *info; 588 int status; 589 590 spi_flash = dev_get_uclass_priv(dev); 591 spi_flash->spi = spi; 592 spi_flash->dev = dev; 593 594 status = spi_claim_bus(spi); 595 if (status) 596 return status; 597 598 /* 599 * Try to detect dataflash by JEDEC ID. 600 * If it succeeds we know we have either a C or D part. 601 * D will support power of 2 pagesize option. 602 * Both support the security register, though with different 603 * write procedures. 604 */ 605 info = jedec_probe(spi); 606 if (IS_ERR(info)) 607 goto err_jedec_probe; 608 if (info != NULL) { 609 status = add_dataflash(dev, info->name, info->nr_pages, 610 info->pagesize, info->pageoffset, 611 (info->flags & SUP_POW2PS) ? 'd' : 'c'); 612 if (status < 0) 613 goto err_status; 614 } 615 616 /* 617 * Older chips support only legacy commands, identifing 618 * capacity using bits in the status byte. 619 */ 620 status = dataflash_status(spi); 621 if (status <= 0 || status == 0xff) { 622 printf("dataflash: read status error %d\n", status); 623 if (status == 0 || status == 0xff) 624 status = -ENODEV; 625 goto err_jedec_probe; 626 } 627 628 /* 629 * if there's a device there, assume it's dataflash. 630 * board setup should have set spi->max_speed_max to 631 * match f(car) for continuous reads, mode 0 or 3. 632 */ 633 switch (status & 0x3c) { 634 case 0x0c: /* 0 0 1 1 x x */ 635 status = add_dataflash(dev, "AT45DB011B", 512, 264, 9, 0); 636 break; 637 case 0x14: /* 0 1 0 1 x x */ 638 status = add_dataflash(dev, "AT45DB021B", 1024, 264, 9, 0); 639 break; 640 case 0x1c: /* 0 1 1 1 x x */ 641 status = add_dataflash(dev, "AT45DB041x", 2048, 264, 9, 0); 642 break; 643 case 0x24: /* 1 0 0 1 x x */ 644 status = add_dataflash(dev, "AT45DB081B", 4096, 264, 9, 0); 645 break; 646 case 0x2c: /* 1 0 1 1 x x */ 647 status = add_dataflash(dev, "AT45DB161x", 4096, 528, 10, 0); 648 break; 649 case 0x34: /* 1 1 0 1 x x */ 650 status = add_dataflash(dev, "AT45DB321x", 8192, 528, 10, 0); 651 break; 652 case 0x38: /* 1 1 1 x x x */ 653 case 0x3c: 654 status = add_dataflash(dev, "AT45DB642x", 8192, 1056, 11, 0); 655 break; 656 /* obsolete AT45DB1282 not (yet?) supported */ 657 default: 658 printf("dataflash: unsupported device (%x)\n", status & 0x3c); 659 status = -ENODEV; 660 goto err_status; 661 } 662 663 return status; 664 665 err_status: 666 spi_free_slave(spi); 667 err_jedec_probe: 668 spi_release_bus(spi); 669 return status; 670 } 671 672 static const struct dm_spi_flash_ops spi_dataflash_ops = { 673 .read = spi_dataflash_read, 674 .write = spi_dataflash_write, 675 .erase = spi_dataflash_erase, 676 }; 677 678 static const struct udevice_id spi_dataflash_ids[] = { 679 { .compatible = "atmel,at45", }, 680 { .compatible = "atmel,dataflash", }, 681 { } 682 }; 683 684 U_BOOT_DRIVER(spi_dataflash) = { 685 .name = "spi_dataflash", 686 .id = UCLASS_SPI_FLASH, 687 .of_match = spi_dataflash_ids, 688 .probe = spi_dataflash_probe, 689 .priv_auto_alloc_size = sizeof(struct dataflash), 690 .ops = &spi_dataflash_ops, 691 }; 692