1 /* 2 * 3 * Atmel DataFlash probing 4 * 5 * Copyright (C) 2004-2009, 2015 Freescale Semiconductor, Inc. 6 * Haikun Wang (haikun.wang@freescale.com) 7 * 8 * SPDX-License-Identifier: GPL-2.0+ 9 */ 10 #include <common.h> 11 #include <dm.h> 12 #include <errno.h> 13 #include <fdtdec.h> 14 #include <spi.h> 15 #include <spi_flash.h> 16 #include <div64.h> 17 #include <linux/err.h> 18 #include <linux/math64.h> 19 20 #include "sf_internal.h" 21 22 /* reads can bypass the buffers */ 23 #define OP_READ_CONTINUOUS 0xE8 24 #define OP_READ_PAGE 0xD2 25 26 /* group B requests can run even while status reports "busy" */ 27 #define OP_READ_STATUS 0xD7 /* group B */ 28 29 /* move data between host and buffer */ 30 #define OP_READ_BUFFER1 0xD4 /* group B */ 31 #define OP_READ_BUFFER2 0xD6 /* group B */ 32 #define OP_WRITE_BUFFER1 0x84 /* group B */ 33 #define OP_WRITE_BUFFER2 0x87 /* group B */ 34 35 /* erasing flash */ 36 #define OP_ERASE_PAGE 0x81 37 #define OP_ERASE_BLOCK 0x50 38 39 /* move data between buffer and flash */ 40 #define OP_TRANSFER_BUF1 0x53 41 #define OP_TRANSFER_BUF2 0x55 42 #define OP_MREAD_BUFFER1 0xD4 43 #define OP_MREAD_BUFFER2 0xD6 44 #define OP_MWERASE_BUFFER1 0x83 45 #define OP_MWERASE_BUFFER2 0x86 46 #define OP_MWRITE_BUFFER1 0x88 /* sector must be pre-erased */ 47 #define OP_MWRITE_BUFFER2 0x89 /* sector must be pre-erased */ 48 49 /* write to buffer, then write-erase to flash */ 50 #define OP_PROGRAM_VIA_BUF1 0x82 51 #define OP_PROGRAM_VIA_BUF2 0x85 52 53 /* compare buffer to flash */ 54 #define OP_COMPARE_BUF1 0x60 55 #define OP_COMPARE_BUF2 0x61 56 57 /* read flash to buffer, then write-erase to flash */ 58 #define OP_REWRITE_VIA_BUF1 0x58 59 #define OP_REWRITE_VIA_BUF2 0x59 60 61 /* 62 * newer chips report JEDEC manufacturer and device IDs; chip 63 * serial number and OTP bits; and per-sector writeprotect. 64 */ 65 #define OP_READ_ID 0x9F 66 #define OP_READ_SECURITY 0x77 67 #define OP_WRITE_SECURITY_REVC 0x9A 68 #define OP_WRITE_SECURITY 0x9B /* revision D */ 69 70 71 struct dataflash { 72 uint8_t command[16]; 73 unsigned short page_offset; /* offset in flash address */ 74 }; 75 76 /* 77 * Return the status of the DataFlash device. 78 */ 79 static inline int dataflash_status(struct spi_slave *spi) 80 { 81 int ret; 82 u8 status; 83 /* 84 * NOTE: at45db321c over 25 MHz wants to write 85 * a dummy byte after the opcode... 86 */ 87 ret = spi_flash_cmd(spi, OP_READ_STATUS, &status, 1); 88 return ret ? -EIO : status; 89 } 90 91 /* 92 * Poll the DataFlash device until it is READY. 93 * This usually takes 5-20 msec or so; more for sector erase. 94 * ready: return > 0 95 */ 96 static int dataflash_waitready(struct spi_slave *spi) 97 { 98 int status; 99 int timeout = 2 * CONFIG_SYS_HZ; 100 int timebase; 101 102 timebase = get_timer(0); 103 do { 104 status = dataflash_status(spi); 105 if (status < 0) 106 status = 0; 107 108 if (status & (1 << 7)) /* RDY/nBSY */ 109 return status; 110 111 mdelay(3); 112 } while (get_timer(timebase) < timeout); 113 114 return -ETIME; 115 } 116 117 /* 118 * Erase pages of flash. 119 */ 120 static int spi_dataflash_erase(struct udevice *dev, u32 offset, size_t len) 121 { 122 struct dataflash *dataflash; 123 struct spi_flash *spi_flash; 124 struct spi_slave *spi; 125 unsigned blocksize; 126 uint8_t *command; 127 uint32_t rem; 128 int status; 129 130 dataflash = dev_get_priv(dev); 131 spi_flash = dev_get_uclass_priv(dev); 132 spi = spi_flash->spi; 133 134 blocksize = spi_flash->page_size << 3; 135 136 memset(dataflash->command, 0 , sizeof(dataflash->command)); 137 command = dataflash->command; 138 139 debug("%s: erase addr=0x%x len 0x%x\n", dev->name, offset, len); 140 141 div_u64_rem(len, spi_flash->page_size, &rem); 142 if (rem) 143 return -EINVAL; 144 div_u64_rem(offset, spi_flash->page_size, &rem); 145 if (rem) 146 return -EINVAL; 147 148 status = spi_claim_bus(spi); 149 if (status) { 150 debug("SPI DATAFLASH: unable to claim SPI bus\n"); 151 return status; 152 } 153 154 while (len > 0) { 155 unsigned int pageaddr; 156 int do_block; 157 /* 158 * Calculate flash page address; use block erase (for speed) if 159 * we're at a block boundary and need to erase the whole block. 160 */ 161 pageaddr = div_u64(offset, spi_flash->page_size); 162 do_block = (pageaddr & 0x7) == 0 && len >= blocksize; 163 pageaddr = pageaddr << dataflash->page_offset; 164 165 command[0] = do_block ? OP_ERASE_BLOCK : OP_ERASE_PAGE; 166 command[1] = (uint8_t)(pageaddr >> 16); 167 command[2] = (uint8_t)(pageaddr >> 8); 168 command[3] = 0; 169 170 debug("%s ERASE %s: (%x) %x %x %x [%d]\n", 171 dev->name, do_block ? "block" : "page", 172 command[0], command[1], command[2], command[3], 173 pageaddr); 174 175 status = spi_flash_cmd_write(spi, command, 4, NULL, 0); 176 if (status < 0) { 177 debug("%s: erase send command error!\n", dev->name); 178 return -EIO; 179 } 180 181 status = dataflash_waitready(spi); 182 if (status < 0) { 183 debug("%s: erase waitready error!\n", dev->name); 184 return status; 185 } 186 187 if (do_block) { 188 offset += blocksize; 189 len -= blocksize; 190 } else { 191 offset += spi_flash->page_size; 192 len -= spi_flash->page_size; 193 } 194 } 195 196 spi_release_bus(spi); 197 198 return 0; 199 } 200 201 /* 202 * Read from the DataFlash device. 203 * offset : Start offset in flash device 204 * len : Amount to read 205 * buf : Buffer containing the data 206 */ 207 static int spi_dataflash_read(struct udevice *dev, u32 offset, size_t len, 208 void *buf) 209 { 210 struct dataflash *dataflash; 211 struct spi_flash *spi_flash; 212 struct spi_slave *spi; 213 unsigned int addr; 214 uint8_t *command; 215 int status; 216 217 dataflash = dev_get_priv(dev); 218 spi_flash = dev_get_uclass_priv(dev); 219 spi = spi_flash->spi; 220 221 memset(dataflash->command, 0 , sizeof(dataflash->command)); 222 command = dataflash->command; 223 224 debug("%s: erase addr=0x%x len 0x%x\n", dev->name, offset, len); 225 debug("READ: (%x) %x %x %x\n", 226 command[0], command[1], command[2], command[3]); 227 228 /* Calculate flash page/byte address */ 229 addr = (((unsigned)offset / spi_flash->page_size) 230 << dataflash->page_offset) 231 + ((unsigned)offset % spi_flash->page_size); 232 233 status = spi_claim_bus(spi); 234 if (status) { 235 debug("SPI DATAFLASH: unable to claim SPI bus\n"); 236 return status; 237 } 238 239 /* 240 * Continuous read, max clock = f(car) which may be less than 241 * the peak rate available. Some chips support commands with 242 * fewer "don't care" bytes. Both buffers stay unchanged. 243 */ 244 command[0] = OP_READ_CONTINUOUS; 245 command[1] = (uint8_t)(addr >> 16); 246 command[2] = (uint8_t)(addr >> 8); 247 command[3] = (uint8_t)(addr >> 0); 248 249 /* plus 4 "don't care" bytes, command len: 4 + 4 "don't care" bytes */ 250 status = spi_flash_cmd_read(spi, command, 8, buf, len); 251 252 spi_release_bus(spi); 253 254 return status; 255 } 256 257 /* 258 * Write to the DataFlash device. 259 * offset : Start offset in flash device 260 * len : Amount to write 261 * buf : Buffer containing the data 262 */ 263 int spi_dataflash_write(struct udevice *dev, u32 offset, size_t len, 264 const void *buf) 265 { 266 struct dataflash *dataflash; 267 struct spi_flash *spi_flash; 268 struct spi_slave *spi; 269 uint8_t *command; 270 unsigned int pageaddr, addr, to, writelen; 271 size_t remaining = len; 272 u_char *writebuf = (u_char *)buf; 273 int status = -EINVAL; 274 275 dataflash = dev_get_priv(dev); 276 spi_flash = dev_get_uclass_priv(dev); 277 spi = spi_flash->spi; 278 279 memset(dataflash->command, 0 , sizeof(dataflash->command)); 280 command = dataflash->command; 281 282 debug("%s: write 0x%x..0x%x\n", dev->name, offset, (offset + len)); 283 284 pageaddr = ((unsigned)offset / spi_flash->page_size); 285 to = ((unsigned)offset % spi_flash->page_size); 286 if (to + len > spi_flash->page_size) 287 writelen = spi_flash->page_size - to; 288 else 289 writelen = len; 290 291 status = spi_claim_bus(spi); 292 if (status) { 293 debug("SPI DATAFLASH: unable to claim SPI bus\n"); 294 return status; 295 } 296 297 while (remaining > 0) { 298 debug("write @ %d:%d len=%d\n", pageaddr, to, writelen); 299 300 /* 301 * REVISIT: 302 * (a) each page in a sector must be rewritten at least 303 * once every 10K sibling erase/program operations. 304 * (b) for pages that are already erased, we could 305 * use WRITE+MWRITE not PROGRAM for ~30% speedup. 306 * (c) WRITE to buffer could be done while waiting for 307 * a previous MWRITE/MWERASE to complete ... 308 * (d) error handling here seems to be mostly missing. 309 * 310 * Two persistent bits per page, plus a per-sector counter, 311 * could support (a) and (b) ... we might consider using 312 * the second half of sector zero, which is just one block, 313 * to track that state. (On AT91, that sector should also 314 * support boot-from-DataFlash.) 315 */ 316 317 addr = pageaddr << dataflash->page_offset; 318 319 /* (1) Maybe transfer partial page to Buffer1 */ 320 if (writelen != spi_flash->page_size) { 321 command[0] = OP_TRANSFER_BUF1; 322 command[1] = (addr & 0x00FF0000) >> 16; 323 command[2] = (addr & 0x0000FF00) >> 8; 324 command[3] = 0; 325 326 debug("TRANSFER: (%x) %x %x %x\n", 327 command[0], command[1], command[2], command[3]); 328 329 status = spi_flash_cmd_write(spi, command, 4, NULL, 0); 330 if (status < 0) { 331 debug("%s: write(<pagesize) command error!\n", 332 dev->name); 333 return -EIO; 334 } 335 336 status = dataflash_waitready(spi); 337 if (status < 0) { 338 debug("%s: write(<pagesize) waitready error!\n", 339 dev->name); 340 return status; 341 } 342 } 343 344 /* (2) Program full page via Buffer1 */ 345 addr += to; 346 command[0] = OP_PROGRAM_VIA_BUF1; 347 command[1] = (addr & 0x00FF0000) >> 16; 348 command[2] = (addr & 0x0000FF00) >> 8; 349 command[3] = (addr & 0x000000FF); 350 351 debug("PROGRAM: (%x) %x %x %x\n", 352 command[0], command[1], command[2], command[3]); 353 354 status = spi_flash_cmd_write(spi, command, 355 4, writebuf, writelen); 356 if (status < 0) { 357 debug("%s: write send command error!\n", dev->name); 358 return -EIO; 359 } 360 361 status = dataflash_waitready(spi); 362 if (status < 0) { 363 debug("%s: write waitready error!\n", dev->name); 364 return status; 365 } 366 367 #ifdef CONFIG_SPI_DATAFLASH_WRITE_VERIFY 368 /* (3) Compare to Buffer1 */ 369 addr = pageaddr << dataflash->page_offset; 370 command[0] = OP_COMPARE_BUF1; 371 command[1] = (addr & 0x00FF0000) >> 16; 372 command[2] = (addr & 0x0000FF00) >> 8; 373 command[3] = 0; 374 375 debug("COMPARE: (%x) %x %x %x\n", 376 command[0], command[1], command[2], command[3]); 377 378 status = spi_flash_cmd_write(spi, command, 379 4, writebuf, writelen); 380 if (status < 0) { 381 debug("%s: write(compare) send command error!\n", 382 dev->name); 383 return -EIO; 384 } 385 386 status = dataflash_waitready(spi); 387 388 /* Check result of the compare operation */ 389 if (status & (1 << 6)) { 390 printf("SPI DataFlash: write compare page %u, err %d\n", 391 pageaddr, status); 392 remaining = 0; 393 status = -EIO; 394 break; 395 } else { 396 status = 0; 397 } 398 399 #endif /* CONFIG_SPI_DATAFLASH_WRITE_VERIFY */ 400 remaining = remaining - writelen; 401 pageaddr++; 402 to = 0; 403 writebuf += writelen; 404 405 if (remaining > spi_flash->page_size) 406 writelen = spi_flash->page_size; 407 else 408 writelen = remaining; 409 } 410 411 spi_release_bus(spi); 412 413 return 0; 414 } 415 416 static int add_dataflash(struct udevice *dev, char *name, int nr_pages, 417 int pagesize, int pageoffset, char revision) 418 { 419 struct spi_flash *spi_flash; 420 struct dataflash *dataflash; 421 422 dataflash = dev_get_priv(dev); 423 spi_flash = dev_get_uclass_priv(dev); 424 425 dataflash->page_offset = pageoffset; 426 427 spi_flash->name = name; 428 spi_flash->page_size = pagesize; 429 spi_flash->size = nr_pages * pagesize; 430 spi_flash->erase_size = pagesize; 431 432 #ifndef CONFIG_SPL_BUILD 433 printf("SPI DataFlash: Detected %s with page size ", spi_flash->name); 434 print_size(spi_flash->page_size, ", erase size "); 435 print_size(spi_flash->erase_size, ", total "); 436 print_size(spi_flash->size, ""); 437 printf(", revision %c", revision); 438 puts("\n"); 439 #endif 440 441 return 0; 442 } 443 444 struct flash_info { 445 char *name; 446 447 /* 448 * JEDEC id has a high byte of zero plus three data bytes: 449 * the manufacturer id, then a two byte device id. 450 */ 451 uint32_t jedec_id; 452 453 /* The size listed here is what works with OP_ERASE_PAGE. */ 454 unsigned nr_pages; 455 uint16_t pagesize; 456 uint16_t pageoffset; 457 458 uint16_t flags; 459 #define SUP_POW2PS 0x0002 /* supports 2^N byte pages */ 460 #define IS_POW2PS 0x0001 /* uses 2^N byte pages */ 461 }; 462 463 static struct flash_info dataflash_data[] = { 464 /* 465 * NOTE: chips with SUP_POW2PS (rev D and up) need two entries, 466 * one with IS_POW2PS and the other without. The entry with the 467 * non-2^N byte page size can't name exact chip revisions without 468 * losing backwards compatibility for cmdlinepart. 469 * 470 * Those two entries have different name spelling format in order to 471 * show their difference obviously. 472 * The upper case refer to the chip isn't in normal 2^N bytes page-size 473 * mode. 474 * The lower case refer to the chip is in normal 2^N bytes page-size 475 * mode. 476 * 477 * These newer chips also support 128-byte security registers (with 478 * 64 bytes one-time-programmable) and software write-protection. 479 */ 480 { "AT45DB011B", 0x1f2200, 512, 264, 9, SUP_POW2PS}, 481 { "at45db011d", 0x1f2200, 512, 256, 8, SUP_POW2PS | IS_POW2PS}, 482 483 { "AT45DB021B", 0x1f2300, 1024, 264, 9, SUP_POW2PS}, 484 { "at45db021d", 0x1f2300, 1024, 256, 8, SUP_POW2PS | IS_POW2PS}, 485 486 { "AT45DB041x", 0x1f2400, 2048, 264, 9, SUP_POW2PS}, 487 { "at45db041d", 0x1f2400, 2048, 256, 8, SUP_POW2PS | IS_POW2PS}, 488 489 { "AT45DB081B", 0x1f2500, 4096, 264, 9, SUP_POW2PS}, 490 { "at45db081d", 0x1f2500, 4096, 256, 8, SUP_POW2PS | IS_POW2PS}, 491 492 { "AT45DB161x", 0x1f2600, 4096, 528, 10, SUP_POW2PS}, 493 { "at45db161d", 0x1f2600, 4096, 512, 9, SUP_POW2PS | IS_POW2PS}, 494 495 { "AT45DB321x", 0x1f2700, 8192, 528, 10, 0}, /* rev C */ 496 497 { "AT45DB321x", 0x1f2701, 8192, 528, 10, SUP_POW2PS}, 498 { "at45db321d", 0x1f2701, 8192, 512, 9, SUP_POW2PS | IS_POW2PS}, 499 500 { "AT45DB642x", 0x1f2800, 8192, 1056, 11, SUP_POW2PS}, 501 { "at45db642d", 0x1f2800, 8192, 1024, 10, SUP_POW2PS | IS_POW2PS}, 502 }; 503 504 static struct flash_info *jedec_probe(struct spi_slave *spi, u8 *id) 505 { 506 int tmp; 507 uint32_t jedec; 508 struct flash_info *info; 509 int status; 510 511 /* 512 * JEDEC also defines an optional "extended device information" 513 * string for after vendor-specific data, after the three bytes 514 * we use here. Supporting some chips might require using it. 515 * 516 * If the vendor ID isn't Atmel's (0x1f), assume this call failed. 517 * That's not an error; only rev C and newer chips handle it, and 518 * only Atmel sells these chips. 519 */ 520 if (id[0] != 0x1f) 521 return NULL; 522 523 jedec = id[0]; 524 jedec = jedec << 8; 525 jedec |= id[1]; 526 jedec = jedec << 8; 527 jedec |= id[2]; 528 529 for (tmp = 0, info = dataflash_data; 530 tmp < ARRAY_SIZE(dataflash_data); 531 tmp++, info++) { 532 if (info->jedec_id == jedec) { 533 if (info->flags & SUP_POW2PS) { 534 status = dataflash_status(spi); 535 if (status < 0) { 536 debug("SPI DataFlash: status error %d\n", 537 status); 538 return NULL; 539 } 540 if (status & 0x1) { 541 if (info->flags & IS_POW2PS) 542 return info; 543 } else { 544 if (!(info->flags & IS_POW2PS)) 545 return info; 546 } 547 } else { 548 return info; 549 } 550 } 551 } 552 553 /* 554 * Treat other chips as errors ... we won't know the right page 555 * size (it might be binary) even when we can tell which density 556 * class is involved (legacy chip id scheme). 557 */ 558 printf("SPI DataFlash: Unsupported flash IDs: "); 559 printf("manuf %02x, jedec %04x, ext_jedec %04x\n", 560 id[0], jedec, id[3] << 8 | id[4]); 561 return NULL; 562 } 563 564 /* 565 * Detect and initialize DataFlash device, using JEDEC IDs on newer chips 566 * or else the ID code embedded in the status bits: 567 * 568 * Device Density ID code #Pages PageSize Offset 569 * AT45DB011B 1Mbit (128K) xx0011xx (0x0c) 512 264 9 570 * AT45DB021B 2Mbit (256K) xx0101xx (0x14) 1024 264 9 571 * AT45DB041B 4Mbit (512K) xx0111xx (0x1c) 2048 264 9 572 * AT45DB081B 8Mbit (1M) xx1001xx (0x24) 4096 264 9 573 * AT45DB0161B 16Mbit (2M) xx1011xx (0x2c) 4096 528 10 574 * AT45DB0321B 32Mbit (4M) xx1101xx (0x34) 8192 528 10 575 * AT45DB0642 64Mbit (8M) xx111xxx (0x3c) 8192 1056 11 576 * AT45DB1282 128Mbit (16M) xx0100xx (0x10) 16384 1056 11 577 */ 578 static int spi_dataflash_probe(struct udevice *dev) 579 { 580 struct spi_slave *spi = dev_get_parentdata(dev); 581 struct spi_flash *spi_flash; 582 struct flash_info *info; 583 u8 idcode[5]; 584 int ret, status = 0; 585 586 spi_flash = dev_get_uclass_priv(dev); 587 spi_flash->dev = dev; 588 589 ret = spi_claim_bus(spi); 590 if (ret) 591 return ret; 592 593 ret = spi_flash_cmd(spi, CMD_READ_ID, idcode, sizeof(idcode)); 594 if (ret) { 595 printf("SPI DataFlash: Failed to get idcodes\n"); 596 goto err_read_cmd; 597 } 598 599 /* 600 * Try to detect dataflash by JEDEC ID. 601 * If it succeeds we know we have either a C or D part. 602 * D will support power of 2 pagesize option. 603 * Both support the security register, though with different 604 * write procedures. 605 */ 606 info = jedec_probe(spi, idcode); 607 if (info != NULL) 608 add_dataflash(dev, info->name, info->nr_pages, 609 info->pagesize, info->pageoffset, 610 (info->flags & SUP_POW2PS) ? 'd' : 'c'); 611 else { 612 /* 613 * Older chips support only legacy commands, identifing 614 * capacity using bits in the status byte. 615 */ 616 status = dataflash_status(spi); 617 if (status <= 0 || status == 0xff) { 618 printf("SPI DataFlash: read status error %d\n", status); 619 if (status == 0 || status == 0xff) 620 status = -ENODEV; 621 goto err_read_cmd; 622 } 623 /* 624 * if there's a device there, assume it's dataflash. 625 * board setup should have set spi->max_speed_max to 626 * match f(car) for continuous reads, mode 0 or 3. 627 */ 628 switch (status & 0x3c) { 629 case 0x0c: /* 0 0 1 1 x x */ 630 status = add_dataflash(dev, "AT45DB011B", 631 512, 264, 9, 0); 632 break; 633 case 0x14: /* 0 1 0 1 x x */ 634 status = add_dataflash(dev, "AT45DB021B", 635 1024, 264, 9, 0); 636 break; 637 case 0x1c: /* 0 1 1 1 x x */ 638 status = add_dataflash(dev, "AT45DB041x", 639 2048, 264, 9, 0); 640 break; 641 case 0x24: /* 1 0 0 1 x x */ 642 status = add_dataflash(dev, "AT45DB081B", 643 4096, 264, 9, 0); 644 break; 645 case 0x2c: /* 1 0 1 1 x x */ 646 status = add_dataflash(dev, "AT45DB161x", 647 4096, 528, 10, 0); 648 break; 649 case 0x34: /* 1 1 0 1 x x */ 650 status = add_dataflash(dev, "AT45DB321x", 651 8192, 528, 10, 0); 652 break; 653 case 0x38: /* 1 1 1 x x x */ 654 case 0x3c: 655 status = add_dataflash(dev, "AT45DB642x", 656 8192, 1056, 11, 0); 657 break; 658 /* obsolete AT45DB1282 not (yet?) supported */ 659 default: 660 dev_info(&spi->dev, "unsupported device (%x)\n", 661 status & 0x3c); 662 status = -ENODEV; 663 goto err_read_cmd; 664 } 665 } 666 667 /* Assign spi data */ 668 spi_flash->spi = spi; 669 spi_flash->memory_map = spi->memory_map; 670 spi_flash->dual_flash = spi->option; 671 672 spi_release_bus(spi); 673 674 return 0; 675 676 err_read_cmd: 677 spi_release_bus(spi); 678 679 return status; 680 } 681 682 static const struct dm_spi_flash_ops spi_dataflash_ops = { 683 .read = spi_dataflash_read, 684 .write = spi_dataflash_write, 685 .erase = spi_dataflash_erase, 686 }; 687 688 static const struct udevice_id spi_dataflash_ids[] = { 689 { .compatible = "atmel,at45", }, 690 { .compatible = "atmel,dataflash", }, 691 { } 692 }; 693 694 U_BOOT_DRIVER(spi_dataflash) = { 695 .name = "spi_dataflash", 696 .id = UCLASS_SPI_FLASH, 697 .of_match = spi_dataflash_ids, 698 .probe = spi_dataflash_probe, 699 .priv_auto_alloc_size = sizeof(struct dataflash), 700 .ops = &spi_dataflash_ops, 701 }; 702