1menu "NAND Device Support" 2 3config SYS_NAND_SELF_INIT 4 bool 5 help 6 This option, if enabled, provides more flexible and linux-like 7 NAND initialization process. 8 9config NAND_DENALI 10 bool "Support Denali NAND controller" 11 select SYS_NAND_SELF_INIT 12 help 13 Enable support for the Denali NAND controller. 14 15config SYS_NAND_DENALI_64BIT 16 bool "Use 64-bit variant of Denali NAND controller" 17 depends on NAND_DENALI 18 help 19 The Denali NAND controller IP has some variations in terms of 20 the bus interface. The DMA setup sequence is completely differenct 21 between 32bit / 64bit AXI bus variants. 22 23 If your Denali NAND controller is the 64-bit variant, say Y. 24 Otherwise (32 bit), say N. 25 26config NAND_DENALI_SPARE_AREA_SKIP_BYTES 27 int "Number of bytes skipped in OOB area" 28 depends on NAND_DENALI 29 range 0 63 30 help 31 This option specifies the number of bytes to skip from the beginning 32 of OOB area before last ECC sector data starts. This is potentially 33 used to preserve the bad block marker in the OOB area. 34 35config NAND_VF610_NFC 36 bool "Support for Freescale NFC for VF610/MPC5125" 37 select SYS_NAND_SELF_INIT 38 help 39 Enables support for NAND Flash Controller on some Freescale 40 processors like the VF610, MPC5125, MCF54418 or Kinetis K70. 41 The driver supports a maximum 2k page size. The driver 42 currently does not support hardware ECC. 43 44choice 45 prompt "Hardware ECC strength" 46 depends on NAND_VF610_NFC 47 default SYS_NAND_VF610_NFC_45_ECC_BYTES 48 help 49 Select the ECC strength used in the hardware BCH ECC block. 50 51config SYS_NAND_VF610_NFC_45_ECC_BYTES 52 bool "24-error correction (45 ECC bytes)" 53 54config SYS_NAND_VF610_NFC_60_ECC_BYTES 55 bool "32-error correction (60 ECC bytes)" 56 57endchoice 58 59config NAND_PXA3XX 60 bool "Support for NAND on PXA3xx and Armada 370/XP/38x" 61 select SYS_NAND_SELF_INIT 62 help 63 This enables the driver for the NAND flash device found on 64 PXA3xx processors (NFCv1) and also on Armada 370/XP (NFCv2). 65 66config NAND_SUNXI 67 bool "Support for NAND on Allwinner SoCs" 68 depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I 69 select SYS_NAND_SELF_INIT 70 ---help--- 71 Enable support for NAND. This option enables the standard and 72 SPL drivers. 73 The SPL driver only supports reading from the NAND using DMA 74 transfers. 75 76config NAND_ARASAN 77 bool "Configure Arasan Nand" 78 help 79 This enables Nand driver support for Arasan nand flash 80 controller. This uses the hardware ECC for read and 81 write operations. 82 83comment "Generic NAND options" 84 85# Enhance depends when converting drivers to Kconfig which use this config 86# option (mxc_nand, ndfc, omap_gpmc). 87config SYS_NAND_BUSWIDTH_16BIT 88 bool "Use 16-bit NAND interface" 89 depends on NAND_VF610_NFC 90 help 91 Indicates that NAND device has 16-bit wide data-bus. In absence of this 92 config, bus-width of NAND device is assumed to be either 8-bit and later 93 determined by reading ONFI params. 94 Above config is useful when NAND device's bus-width information cannot 95 be determined from on-chip ONFI params, like in following scenarios: 96 - SPL boot does not support reading of ONFI parameters. This is done to 97 keep SPL code foot-print small. 98 - In current U-Boot flow using nand_init(), driver initialization 99 happens in board_nand_init() which is called before any device probe 100 (nand_scan_ident + nand_scan_tail), thus device's ONFI parameters are 101 not available while configuring controller. So a static CONFIG_NAND_xx 102 is needed to know the device's bus-width in advance. 103 104if SPL 105 106config SYS_NAND_U_BOOT_LOCATIONS 107 bool "Define U-boot binaries locations in NAND" 108 help 109 Enable CONFIG_SYS_NAND_U_BOOT_OFFS though Kconfig. 110 This option should not be enabled when compiling U-boot for boards 111 defining CONFIG_SYS_NAND_U_BOOT_OFFS in their include/configs/<board>.h 112 file. 113 114config SYS_NAND_U_BOOT_OFFS 115 hex "Location in NAND to read U-Boot from" 116 default 0x8000 if NAND_SUNXI 117 depends on SYS_NAND_U_BOOT_LOCATIONS 118 help 119 Set the offset from the start of the nand where u-boot should be 120 loaded from. 121 122config SYS_NAND_U_BOOT_OFFS_REDUND 123 hex "Location in NAND to read U-Boot from" 124 default SYS_NAND_U_BOOT_OFFS 125 depends on SYS_NAND_U_BOOT_LOCATIONS 126 help 127 Set the offset from the start of the nand where the redundant u-boot 128 should be loaded from. 129 130config SPL_NAND_DENALI 131 bool "Support Denali NAND controller for SPL" 132 help 133 This is a small implementation of the Denali NAND controller 134 for use on SPL. 135 136endif 137 138endmenu 139