xref: /openbmc/u-boot/drivers/mtd/nand/Kconfig (revision c66f5620)
1
2menuconfig NAND
3	bool "NAND Device Support"
4if NAND
5
6config SYS_NAND_SELF_INIT
7	bool
8	help
9	  This option, if enabled, provides more flexible and linux-like
10	  NAND initialization process.
11
12config NAND_DENALI
13	bool
14	select SYS_NAND_SELF_INIT
15	imply CMD_NAND
16
17config NAND_DENALI_DT
18	bool "Support Denali NAND controller as a DT device"
19	select NAND_DENALI
20	depends on OF_CONTROL && DM
21	help
22	  Enable the driver for NAND flash on platforms using a Denali NAND
23	  controller as a DT device.
24
25config NAND_DENALI_SPARE_AREA_SKIP_BYTES
26	int "Number of bytes skipped in OOB area"
27	depends on NAND_DENALI
28	range 0 63
29	help
30	  This option specifies the number of bytes to skip from the beginning
31	  of OOB area before last ECC sector data starts.  This is potentially
32	  used to preserve the bad block marker in the OOB area.
33
34config NAND_OMAP_GPMC
35	bool "Support OMAP GPMC NAND controller"
36	depends on ARCH_OMAP2PLUS
37	help
38	  Enables omap_gpmc.c driver for OMAPx and AMxxxx platforms.
39	  GPMC controller is used for parallel NAND flash devices, and can
40	  do ECC calculation (not ECC error detection) for HAM1, BCH4, BCH8
41	  and BCH16 ECC algorithms.
42
43config NAND_OMAP_GPMC_PREFETCH
44	bool "Enable GPMC Prefetch"
45	depends on NAND_OMAP_GPMC
46	default y
47	help
48	  On OMAP platforms that use the GPMC controller
49	  (CONFIG_NAND_OMAP_GPMC_PREFETCH), this options enables the code that
50	  uses the prefetch mode to speed up read operations.
51
52config NAND_OMAP_ELM
53	bool "Enable ELM driver for OMAPxx and AMxx platforms."
54	depends on NAND_OMAP_GPMC && !OMAP34XX
55	help
56	  ELM controller is used for ECC error detection (not ECC calculation)
57	  of BCH4, BCH8 and BCH16 ECC algorithms.
58	  Some legacy platforms like OMAP3xx do not have in-built ELM h/w engine,
59	  thus such SoC platforms need to depend on software library for ECC error
60	  detection. However ECC calculation on such plaforms would still be
61	  done by GPMC controller.
62
63config NAND_VF610_NFC
64	bool "Support for Freescale NFC for VF610"
65	select SYS_NAND_SELF_INIT
66	imply CMD_NAND
67	help
68	  Enables support for NAND Flash Controller on some Freescale
69	  processors like the VF610, MCF54418 or Kinetis K70.
70	  The driver supports a maximum 2k page size. The driver
71	  currently does not support hardware ECC.
72
73choice
74	prompt "Hardware ECC strength"
75	depends on NAND_VF610_NFC
76	default SYS_NAND_VF610_NFC_45_ECC_BYTES
77	help
78	  Select the ECC strength used in the hardware BCH ECC block.
79
80config SYS_NAND_VF610_NFC_45_ECC_BYTES
81	bool "24-error correction (45 ECC bytes)"
82
83config SYS_NAND_VF610_NFC_60_ECC_BYTES
84	bool "32-error correction (60 ECC bytes)"
85
86endchoice
87
88config NAND_PXA3XX
89	bool "Support for NAND on PXA3xx and Armada 370/XP/38x"
90	select SYS_NAND_SELF_INIT
91	imply CMD_NAND
92	help
93	  This enables the driver for the NAND flash device found on
94	  PXA3xx processors (NFCv1) and also on Armada 370/XP (NFCv2).
95
96config NAND_SUNXI
97	bool "Support for NAND on Allwinner SoCs"
98	default ARCH_SUNXI
99	depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I || MACH_SUN8I
100	select SYS_NAND_SELF_INIT
101	select SYS_NAND_U_BOOT_LOCATIONS
102	select SPL_NAND_SUPPORT
103	imply CMD_NAND
104	---help---
105	Enable support for NAND. This option enables the standard and
106	SPL drivers.
107	The SPL driver only supports reading from the NAND using DMA
108	transfers.
109
110if NAND_SUNXI
111
112config NAND_SUNXI_SPL_ECC_STRENGTH
113	int "Allwinner NAND SPL ECC Strength"
114	default 64
115
116config NAND_SUNXI_SPL_ECC_SIZE
117	int "Allwinner NAND SPL ECC Step Size"
118	default 1024
119
120config NAND_SUNXI_SPL_USABLE_PAGE_SIZE
121	int "Allwinner NAND SPL Usable Page Size"
122	default 1024
123
124endif
125
126config NAND_ARASAN
127	bool "Configure Arasan Nand"
128	select SYS_NAND_SELF_INIT
129	imply CMD_NAND
130	help
131	  This enables Nand driver support for Arasan nand flash
132	  controller. This uses the hardware ECC for read and
133	  write operations.
134
135config NAND_MXC
136	bool "MXC NAND support"
137	depends on CPU_ARM926EJS || CPU_ARM1136 || MX5
138	imply CMD_NAND
139	help
140	  This enables the NAND driver for the NAND flash controller on the
141	  i.MX27 / i.MX31 / i.MX5 rocessors.
142
143config NAND_MXS
144	bool "MXS NAND support"
145	depends on MX23 || MX28 || MX6 || MX7
146	imply CMD_NAND
147	select APBH_DMA
148	select APBH_DMA_BURST if ARCH_MX6 || ARCH_MX7
149	select APBH_DMA_BURST8 if ARCH_MX6 || ARCH_MX7
150	help
151	  This enables NAND driver for the NAND flash controller on the
152	  MXS processors.
153
154config NAND_ZYNQ
155	bool "Support for Zynq Nand controller"
156	select SYS_NAND_SELF_INIT
157	imply CMD_NAND
158	help
159	  This enables Nand driver support for Nand flash controller
160	  found on Zynq SoC.
161
162config NAND_ZYNQ_USE_BOOTLOADER1_TIMINGS
163	bool "Enable use of 1st stage bootloader timing for NAND"
164	depends on NAND_ZYNQ
165	help
166	  This flag prevent U-boot reconfigure NAND flash controller and reuse
167	  the NAND timing from 1st stage bootloader.
168
169comment "Generic NAND options"
170
171config SYS_NAND_BLOCK_SIZE
172	hex "NAND chip eraseblock size"
173	depends on ARCH_SUNXI
174	help
175	  Number of data bytes in one eraseblock for the NAND chip on the
176	  board. This is the multiple of NAND_PAGE_SIZE and the number of
177	  pages.
178
179config SYS_NAND_PAGE_SIZE
180	hex "NAND chip page size"
181	depends on ARCH_SUNXI
182	help
183	  Number of data bytes in one page for the NAND chip on the
184	  board, not including the OOB area.
185
186config SYS_NAND_OOBSIZE
187	hex "NAND chip OOB size"
188	depends on ARCH_SUNXI
189	help
190	  Number of bytes in the Out-Of-Band area for the NAND chip on
191	  the board.
192
193# Enhance depends when converting drivers to Kconfig which use this config
194# option (mxc_nand, ndfc, omap_gpmc).
195config SYS_NAND_BUSWIDTH_16BIT
196	bool "Use 16-bit NAND interface"
197	depends on NAND_VF610_NFC || NAND_OMAP_GPMC || NAND_MXC || ARCH_DAVINCI
198	help
199	  Indicates that NAND device has 16-bit wide data-bus. In absence of this
200	  config, bus-width of NAND device is assumed to be either 8-bit and later
201	  determined by reading ONFI params.
202	  Above config is useful when NAND device's bus-width information cannot
203	  be determined from on-chip ONFI params, like in following scenarios:
204	  - SPL boot does not support reading of ONFI parameters. This is done to
205	    keep SPL code foot-print small.
206	  - In current U-Boot flow using nand_init(), driver initialization
207	    happens in board_nand_init() which is called before any device probe
208	    (nand_scan_ident + nand_scan_tail), thus device's ONFI parameters are
209	    not available while configuring controller. So a static CONFIG_NAND_xx
210	    is needed to know the device's bus-width in advance.
211
212if SPL
213
214config SYS_NAND_U_BOOT_LOCATIONS
215	bool "Define U-boot binaries locations in NAND"
216	help
217	Enable CONFIG_SYS_NAND_U_BOOT_OFFS though Kconfig.
218	This option should not be enabled when compiling U-boot for boards
219	defining CONFIG_SYS_NAND_U_BOOT_OFFS in their include/configs/<board>.h
220	file.
221
222config SYS_NAND_U_BOOT_OFFS
223	hex "Location in NAND to read U-Boot from"
224	default 0x800000 if NAND_SUNXI
225	depends on SYS_NAND_U_BOOT_LOCATIONS
226	help
227	Set the offset from the start of the nand where u-boot should be
228	loaded from.
229
230config SYS_NAND_U_BOOT_OFFS_REDUND
231	hex "Location in NAND to read U-Boot from"
232	default SYS_NAND_U_BOOT_OFFS
233	depends on SYS_NAND_U_BOOT_LOCATIONS
234	help
235	Set the offset from the start of the nand where the redundant u-boot
236	should be loaded from.
237
238config SPL_NAND_AM33XX_BCH
239	bool "Enables SPL-NAND driver which supports ELM based"
240	depends on NAND_OMAP_GPMC && !OMAP34XX
241	default y
242        help
243	  Hardware ECC correction. This is useful for platforms which have ELM
244	  hardware engine and use NAND boot mode.
245	  Some legacy platforms like OMAP3xx do not have in-built ELM h/w engine,
246	  so those platforms should use CONFIG_SPL_NAND_SIMPLE for enabling
247          SPL-NAND driver with software ECC correction support.
248
249config SPL_NAND_DENALI
250	bool "Support Denali NAND controller for SPL"
251	help
252	  This is a small implementation of the Denali NAND controller
253	  for use on SPL.
254
255config SPL_NAND_SIMPLE
256	bool "Use simple SPL NAND driver"
257	depends on !SPL_NAND_AM33XX_BCH
258	help
259	  Support for NAND boot using simple NAND drivers that
260	  expose the cmd_ctrl() interface.
261endif
262
263endif   # if NAND
264