1 2menuconfig NAND 3 bool "NAND Device Support" 4if NAND 5 6config SYS_NAND_SELF_INIT 7 bool 8 help 9 This option, if enabled, provides more flexible and linux-like 10 NAND initialization process. 11 12config NAND_DENALI 13 bool 14 select SYS_NAND_SELF_INIT 15 imply CMD_NAND 16 17config NAND_DENALI_DT 18 bool "Support Denali NAND controller as a DT device" 19 select NAND_DENALI 20 depends on OF_CONTROL && DM 21 help 22 Enable the driver for NAND flash on platforms using a Denali NAND 23 controller as a DT device. 24 25config NAND_DENALI_SPARE_AREA_SKIP_BYTES 26 int "Number of bytes skipped in OOB area" 27 depends on NAND_DENALI 28 range 0 63 29 help 30 This option specifies the number of bytes to skip from the beginning 31 of OOB area before last ECC sector data starts. This is potentially 32 used to preserve the bad block marker in the OOB area. 33 34config NAND_OMAP_GPMC 35 bool "Support OMAP GPMC NAND controller" 36 depends on ARCH_OMAP2PLUS 37 help 38 Enables omap_gpmc.c driver for OMAPx and AMxxxx platforms. 39 GPMC controller is used for parallel NAND flash devices, and can 40 do ECC calculation (not ECC error detection) for HAM1, BCH4, BCH8 41 and BCH16 ECC algorithms. 42 43config NAND_OMAP_GPMC_PREFETCH 44 bool "Enable GPMC Prefetch" 45 depends on NAND_OMAP_GPMC 46 default y 47 help 48 On OMAP platforms that use the GPMC controller 49 (CONFIG_NAND_OMAP_GPMC_PREFETCH), this options enables the code that 50 uses the prefetch mode to speed up read operations. 51 52config NAND_OMAP_ELM 53 bool "Enable ELM driver for OMAPxx and AMxx platforms." 54 depends on NAND_OMAP_GPMC && !OMAP34XX 55 help 56 ELM controller is used for ECC error detection (not ECC calculation) 57 of BCH4, BCH8 and BCH16 ECC algorithms. 58 Some legacy platforms like OMAP3xx do not have in-built ELM h/w engine, 59 thus such SoC platforms need to depend on software library for ECC error 60 detection. However ECC calculation on such plaforms would still be 61 done by GPMC controller. 62 63config NAND_VF610_NFC 64 bool "Support for Freescale NFC for VF610" 65 select SYS_NAND_SELF_INIT 66 imply CMD_NAND 67 help 68 Enables support for NAND Flash Controller on some Freescale 69 processors like the VF610, MCF54418 or Kinetis K70. 70 The driver supports a maximum 2k page size. The driver 71 currently does not support hardware ECC. 72 73choice 74 prompt "Hardware ECC strength" 75 depends on NAND_VF610_NFC 76 default SYS_NAND_VF610_NFC_45_ECC_BYTES 77 help 78 Select the ECC strength used in the hardware BCH ECC block. 79 80config SYS_NAND_VF610_NFC_45_ECC_BYTES 81 bool "24-error correction (45 ECC bytes)" 82 83config SYS_NAND_VF610_NFC_60_ECC_BYTES 84 bool "32-error correction (60 ECC bytes)" 85 86endchoice 87 88config NAND_PXA3XX 89 bool "Support for NAND on PXA3xx and Armada 370/XP/38x" 90 select SYS_NAND_SELF_INIT 91 imply CMD_NAND 92 help 93 This enables the driver for the NAND flash device found on 94 PXA3xx processors (NFCv1) and also on Armada 370/XP (NFCv2). 95 96config NAND_SUNXI 97 bool "Support for NAND on Allwinner SoCs" 98 depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I 99 select SYS_NAND_SELF_INIT 100 select SYS_NAND_U_BOOT_LOCATIONS 101 imply CMD_NAND 102 ---help--- 103 Enable support for NAND. This option enables the standard and 104 SPL drivers. 105 The SPL driver only supports reading from the NAND using DMA 106 transfers. 107 108if NAND_SUNXI 109 110config NAND_SUNXI_SPL_ECC_STRENGTH 111 int "Allwinner NAND SPL ECC Strength" 112 default 64 113 114config NAND_SUNXI_SPL_ECC_SIZE 115 int "Allwinner NAND SPL ECC Step Size" 116 default 1024 117 118config NAND_SUNXI_SPL_USABLE_PAGE_SIZE 119 int "Allwinner NAND SPL Usable Page Size" 120 default 1024 121 122endif 123 124config NAND_ARASAN 125 bool "Configure Arasan Nand" 126 select SYS_NAND_SELF_INIT 127 imply CMD_NAND 128 help 129 This enables Nand driver support for Arasan nand flash 130 controller. This uses the hardware ECC for read and 131 write operations. 132 133config NAND_MXC 134 bool "MXC NAND support" 135 depends on CPU_ARM926EJS || CPU_ARM1136 || MX5 136 imply CMD_NAND 137 help 138 This enables the NAND driver for the NAND flash controller on the 139 i.MX27 / i.MX31 / i.MX5 rocessors. 140 141config NAND_MXS 142 bool "MXS NAND support" 143 depends on MX6 || MX7 144 imply CMD_NAND 145 help 146 This enables NAND driver for the NAND flash controller on the 147 MXS processors. 148 149config NAND_ZYNQ 150 bool "Support for Zynq Nand controller" 151 select SYS_NAND_SELF_INIT 152 imply CMD_NAND 153 help 154 This enables Nand driver support for Nand flash controller 155 found on Zynq SoC. 156 157config NAND_ZYNQ_USE_BOOTLOADER1_TIMINGS 158 bool "Enable use of 1st stage bootloader timing for NAND" 159 depends on NAND_ZYNQ 160 help 161 This flag prevent U-boot reconfigure NAND flash controller and reuse 162 the NAND timing from 1st stage bootloader. 163 164comment "Generic NAND options" 165 166# Enhance depends when converting drivers to Kconfig which use this config 167# option (mxc_nand, ndfc, omap_gpmc). 168config SYS_NAND_BUSWIDTH_16BIT 169 bool "Use 16-bit NAND interface" 170 depends on NAND_VF610_NFC || NAND_OMAP_GPMC || NAND_MXC || ARCH_DAVINCI 171 help 172 Indicates that NAND device has 16-bit wide data-bus. In absence of this 173 config, bus-width of NAND device is assumed to be either 8-bit and later 174 determined by reading ONFI params. 175 Above config is useful when NAND device's bus-width information cannot 176 be determined from on-chip ONFI params, like in following scenarios: 177 - SPL boot does not support reading of ONFI parameters. This is done to 178 keep SPL code foot-print small. 179 - In current U-Boot flow using nand_init(), driver initialization 180 happens in board_nand_init() which is called before any device probe 181 (nand_scan_ident + nand_scan_tail), thus device's ONFI parameters are 182 not available while configuring controller. So a static CONFIG_NAND_xx 183 is needed to know the device's bus-width in advance. 184 185if SPL 186 187config SYS_NAND_U_BOOT_LOCATIONS 188 bool "Define U-boot binaries locations in NAND" 189 help 190 Enable CONFIG_SYS_NAND_U_BOOT_OFFS though Kconfig. 191 This option should not be enabled when compiling U-boot for boards 192 defining CONFIG_SYS_NAND_U_BOOT_OFFS in their include/configs/<board>.h 193 file. 194 195config SYS_NAND_U_BOOT_OFFS 196 hex "Location in NAND to read U-Boot from" 197 default 0x800000 if NAND_SUNXI 198 depends on SYS_NAND_U_BOOT_LOCATIONS 199 help 200 Set the offset from the start of the nand where u-boot should be 201 loaded from. 202 203config SYS_NAND_U_BOOT_OFFS_REDUND 204 hex "Location in NAND to read U-Boot from" 205 default SYS_NAND_U_BOOT_OFFS 206 depends on SYS_NAND_U_BOOT_LOCATIONS 207 help 208 Set the offset from the start of the nand where the redundant u-boot 209 should be loaded from. 210 211config SPL_NAND_AM33XX_BCH 212 bool "Enables SPL-NAND driver which supports ELM based" 213 depends on NAND_OMAP_GPMC && !OMAP34XX 214 default y 215 help 216 Hardware ECC correction. This is useful for platforms which have ELM 217 hardware engine and use NAND boot mode. 218 Some legacy platforms like OMAP3xx do not have in-built ELM h/w engine, 219 so those platforms should use CONFIG_SPL_NAND_SIMPLE for enabling 220 SPL-NAND driver with software ECC correction support. 221 222config SPL_NAND_DENALI 223 bool "Support Denali NAND controller for SPL" 224 help 225 This is a small implementation of the Denali NAND controller 226 for use on SPL. 227 228config SPL_NAND_SIMPLE 229 bool "Use simple SPL NAND driver" 230 depends on !SPL_NAND_AM33XX_BCH 231 help 232 Support for NAND boot using simple NAND drivers that 233 expose the cmd_ctrl() interface. 234endif 235 236endif # if NAND 237