1 2menuconfig NAND 3 bool "NAND Device Support" 4if NAND 5 6config SYS_NAND_SELF_INIT 7 bool 8 help 9 This option, if enabled, provides more flexible and linux-like 10 NAND initialization process. 11 12config NAND_DENALI 13 bool "Support Denali NAND controller" 14 select SYS_NAND_SELF_INIT 15 imply CMD_NAND 16 help 17 Enable support for the Denali NAND controller. 18 19config NAND_DENALI_DT 20 bool "Support Denali NAND controller as a DT device" 21 depends on NAND_DENALI && OF_CONTROL && DM 22 help 23 Enable the driver for NAND flash on platforms using a Denali NAND 24 controller as a DT device. 25 26config NAND_DENALI_SPARE_AREA_SKIP_BYTES 27 int "Number of bytes skipped in OOB area" 28 depends on NAND_DENALI 29 range 0 63 30 help 31 This option specifies the number of bytes to skip from the beginning 32 of OOB area before last ECC sector data starts. This is potentially 33 used to preserve the bad block marker in the OOB area. 34 35config NAND_OMAP_GPMC 36 bool "Support OMAP GPMC NAND controller" 37 depends on ARCH_OMAP2PLUS 38 help 39 Enables omap_gpmc.c driver for OMAPx and AMxxxx platforms. 40 GPMC controller is used for parallel NAND flash devices, and can 41 do ECC calculation (not ECC error detection) for HAM1, BCH4, BCH8 42 and BCH16 ECC algorithms. 43 44config NAND_OMAP_GPMC_PREFETCH 45 bool "Enable GPMC Prefetch" 46 depends on NAND_OMAP_GPMC 47 default y 48 help 49 On OMAP platforms that use the GPMC controller 50 (CONFIG_NAND_OMAP_GPMC_PREFETCH), this options enables the code that 51 uses the prefetch mode to speed up read operations. 52 53config NAND_OMAP_ELM 54 bool "Enable ELM driver for OMAPxx and AMxx platforms." 55 depends on NAND_OMAP_GPMC && !OMAP34XX 56 help 57 ELM controller is used for ECC error detection (not ECC calculation) 58 of BCH4, BCH8 and BCH16 ECC algorithms. 59 Some legacy platforms like OMAP3xx do not have in-built ELM h/w engine, 60 thus such SoC platforms need to depend on software library for ECC error 61 detection. However ECC calculation on such plaforms would still be 62 done by GPMC controller. 63 64config NAND_VF610_NFC 65 bool "Support for Freescale NFC for VF610" 66 select SYS_NAND_SELF_INIT 67 imply CMD_NAND 68 help 69 Enables support for NAND Flash Controller on some Freescale 70 processors like the VF610, MCF54418 or Kinetis K70. 71 The driver supports a maximum 2k page size. The driver 72 currently does not support hardware ECC. 73 74choice 75 prompt "Hardware ECC strength" 76 depends on NAND_VF610_NFC 77 default SYS_NAND_VF610_NFC_45_ECC_BYTES 78 help 79 Select the ECC strength used in the hardware BCH ECC block. 80 81config SYS_NAND_VF610_NFC_45_ECC_BYTES 82 bool "24-error correction (45 ECC bytes)" 83 84config SYS_NAND_VF610_NFC_60_ECC_BYTES 85 bool "32-error correction (60 ECC bytes)" 86 87endchoice 88 89config NAND_PXA3XX 90 bool "Support for NAND on PXA3xx and Armada 370/XP/38x" 91 select SYS_NAND_SELF_INIT 92 imply CMD_NAND 93 help 94 This enables the driver for the NAND flash device found on 95 PXA3xx processors (NFCv1) and also on Armada 370/XP (NFCv2). 96 97config NAND_SUNXI 98 bool "Support for NAND on Allwinner SoCs" 99 depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I 100 select SYS_NAND_SELF_INIT 101 select SYS_NAND_U_BOOT_LOCATIONS 102 imply CMD_NAND 103 ---help--- 104 Enable support for NAND. This option enables the standard and 105 SPL drivers. 106 The SPL driver only supports reading from the NAND using DMA 107 transfers. 108 109if NAND_SUNXI 110 111config NAND_SUNXI_SPL_ECC_STRENGTH 112 int "Allwinner NAND SPL ECC Strength" 113 default 64 114 115config NAND_SUNXI_SPL_ECC_SIZE 116 int "Allwinner NAND SPL ECC Step Size" 117 default 1024 118 119config NAND_SUNXI_SPL_USABLE_PAGE_SIZE 120 int "Allwinner NAND SPL Usable Page Size" 121 default 1024 122 123endif 124 125config NAND_ARASAN 126 bool "Configure Arasan Nand" 127 imply CMD_NAND 128 help 129 This enables Nand driver support for Arasan nand flash 130 controller. This uses the hardware ECC for read and 131 write operations. 132 133config NAND_MXC 134 bool "MXC NAND support" 135 depends on CPU_ARM926EJS || CPU_ARM1136 || MX5 136 imply CMD_NAND 137 help 138 This enables the NAND driver for the NAND flash controller on the 139 i.MX27 / i.MX31 / i.MX5 rocessors. 140 141config NAND_MXS 142 bool "MXS NAND support" 143 depends on MX6 || MX7 144 imply CMD_NAND 145 help 146 This enables NAND driver for the NAND flash controller on the 147 MXS processors. 148 149config NAND_ZYNQ 150 bool "Support for Zynq Nand controller" 151 select SYS_NAND_SELF_INIT 152 imply CMD_NAND 153 help 154 This enables Nand driver support for Nand flash controller 155 found on Zynq SoC. 156 157comment "Generic NAND options" 158 159# Enhance depends when converting drivers to Kconfig which use this config 160# option (mxc_nand, ndfc, omap_gpmc). 161config SYS_NAND_BUSWIDTH_16BIT 162 bool "Use 16-bit NAND interface" 163 depends on NAND_VF610_NFC || NAND_OMAP_GPMC || NAND_MXC || ARCH_DAVINCI 164 help 165 Indicates that NAND device has 16-bit wide data-bus. In absence of this 166 config, bus-width of NAND device is assumed to be either 8-bit and later 167 determined by reading ONFI params. 168 Above config is useful when NAND device's bus-width information cannot 169 be determined from on-chip ONFI params, like in following scenarios: 170 - SPL boot does not support reading of ONFI parameters. This is done to 171 keep SPL code foot-print small. 172 - In current U-Boot flow using nand_init(), driver initialization 173 happens in board_nand_init() which is called before any device probe 174 (nand_scan_ident + nand_scan_tail), thus device's ONFI parameters are 175 not available while configuring controller. So a static CONFIG_NAND_xx 176 is needed to know the device's bus-width in advance. 177 178if SPL 179 180config SYS_NAND_U_BOOT_LOCATIONS 181 bool "Define U-boot binaries locations in NAND" 182 help 183 Enable CONFIG_SYS_NAND_U_BOOT_OFFS though Kconfig. 184 This option should not be enabled when compiling U-boot for boards 185 defining CONFIG_SYS_NAND_U_BOOT_OFFS in their include/configs/<board>.h 186 file. 187 188config SYS_NAND_U_BOOT_OFFS 189 hex "Location in NAND to read U-Boot from" 190 default 0x800000 if NAND_SUNXI 191 depends on SYS_NAND_U_BOOT_LOCATIONS 192 help 193 Set the offset from the start of the nand where u-boot should be 194 loaded from. 195 196config SYS_NAND_U_BOOT_OFFS_REDUND 197 hex "Location in NAND to read U-Boot from" 198 default SYS_NAND_U_BOOT_OFFS 199 depends on SYS_NAND_U_BOOT_LOCATIONS 200 help 201 Set the offset from the start of the nand where the redundant u-boot 202 should be loaded from. 203 204config SPL_NAND_AM33XX_BCH 205 bool "Enables SPL-NAND driver which supports ELM based" 206 depends on NAND_OMAP_GPMC && !OMAP34XX 207 default y 208 help 209 Hardware ECC correction. This is useful for platforms which have ELM 210 hardware engine and use NAND boot mode. 211 Some legacy platforms like OMAP3xx do not have in-built ELM h/w engine, 212 so those platforms should use CONFIG_SPL_NAND_SIMPLE for enabling 213 SPL-NAND driver with software ECC correction support. 214 215config SPL_NAND_DENALI 216 bool "Support Denali NAND controller for SPL" 217 help 218 This is a small implementation of the Denali NAND controller 219 for use on SPL. 220 221config SPL_NAND_SIMPLE 222 bool "Use simple SPL NAND driver" 223 depends on !SPL_NAND_AM33XX_BCH 224 help 225 Support for NAND boot using simple NAND drivers that 226 expose the cmd_ctrl() interface. 227endif 228 229endif # if NAND 230