1 2menuconfig NAND 3 bool "NAND Device Support" 4if NAND 5 6config SYS_NAND_SELF_INIT 7 bool 8 help 9 This option, if enabled, provides more flexible and linux-like 10 NAND initialization process. 11 12config NAND_DENALI 13 bool 14 select SYS_NAND_SELF_INIT 15 imply CMD_NAND 16 17config NAND_DENALI_DT 18 bool "Support Denali NAND controller as a DT device" 19 select NAND_DENALI 20 depends on OF_CONTROL && DM 21 help 22 Enable the driver for NAND flash on platforms using a Denali NAND 23 controller as a DT device. 24 25config NAND_DENALI_SPARE_AREA_SKIP_BYTES 26 int "Number of bytes skipped in OOB area" 27 depends on NAND_DENALI 28 range 0 63 29 help 30 This option specifies the number of bytes to skip from the beginning 31 of OOB area before last ECC sector data starts. This is potentially 32 used to preserve the bad block marker in the OOB area. 33 34config NAND_OMAP_GPMC 35 bool "Support OMAP GPMC NAND controller" 36 depends on ARCH_OMAP2PLUS 37 help 38 Enables omap_gpmc.c driver for OMAPx and AMxxxx platforms. 39 GPMC controller is used for parallel NAND flash devices, and can 40 do ECC calculation (not ECC error detection) for HAM1, BCH4, BCH8 41 and BCH16 ECC algorithms. 42 43config NAND_OMAP_GPMC_PREFETCH 44 bool "Enable GPMC Prefetch" 45 depends on NAND_OMAP_GPMC 46 default y 47 help 48 On OMAP platforms that use the GPMC controller 49 (CONFIG_NAND_OMAP_GPMC_PREFETCH), this options enables the code that 50 uses the prefetch mode to speed up read operations. 51 52config NAND_OMAP_ELM 53 bool "Enable ELM driver for OMAPxx and AMxx platforms." 54 depends on NAND_OMAP_GPMC && !OMAP34XX 55 help 56 ELM controller is used for ECC error detection (not ECC calculation) 57 of BCH4, BCH8 and BCH16 ECC algorithms. 58 Some legacy platforms like OMAP3xx do not have in-built ELM h/w engine, 59 thus such SoC platforms need to depend on software library for ECC error 60 detection. However ECC calculation on such plaforms would still be 61 done by GPMC controller. 62 63config NAND_VF610_NFC 64 bool "Support for Freescale NFC for VF610" 65 select SYS_NAND_SELF_INIT 66 imply CMD_NAND 67 help 68 Enables support for NAND Flash Controller on some Freescale 69 processors like the VF610, MCF54418 or Kinetis K70. 70 The driver supports a maximum 2k page size. The driver 71 currently does not support hardware ECC. 72 73choice 74 prompt "Hardware ECC strength" 75 depends on NAND_VF610_NFC 76 default SYS_NAND_VF610_NFC_45_ECC_BYTES 77 help 78 Select the ECC strength used in the hardware BCH ECC block. 79 80config SYS_NAND_VF610_NFC_45_ECC_BYTES 81 bool "24-error correction (45 ECC bytes)" 82 83config SYS_NAND_VF610_NFC_60_ECC_BYTES 84 bool "32-error correction (60 ECC bytes)" 85 86endchoice 87 88config NAND_PXA3XX 89 bool "Support for NAND on PXA3xx and Armada 370/XP/38x" 90 select SYS_NAND_SELF_INIT 91 imply CMD_NAND 92 help 93 This enables the driver for the NAND flash device found on 94 PXA3xx processors (NFCv1) and also on Armada 370/XP (NFCv2). 95 96config NAND_SUNXI 97 bool "Support for NAND on Allwinner SoCs" 98 default ARCH_SUNXI 99 depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I || MACH_SUN8I 100 select SYS_NAND_SELF_INIT 101 select SYS_NAND_U_BOOT_LOCATIONS 102 select SPL_NAND_SUPPORT 103 imply CMD_NAND 104 ---help--- 105 Enable support for NAND. This option enables the standard and 106 SPL drivers. 107 The SPL driver only supports reading from the NAND using DMA 108 transfers. 109 110if NAND_SUNXI 111 112config NAND_SUNXI_SPL_ECC_STRENGTH 113 int "Allwinner NAND SPL ECC Strength" 114 default 64 115 116config NAND_SUNXI_SPL_ECC_SIZE 117 int "Allwinner NAND SPL ECC Step Size" 118 default 1024 119 120config NAND_SUNXI_SPL_USABLE_PAGE_SIZE 121 int "Allwinner NAND SPL Usable Page Size" 122 default 1024 123 124endif 125 126config NAND_ARASAN 127 bool "Configure Arasan Nand" 128 select SYS_NAND_SELF_INIT 129 imply CMD_NAND 130 help 131 This enables Nand driver support for Arasan nand flash 132 controller. This uses the hardware ECC for read and 133 write operations. 134 135config NAND_MXC 136 bool "MXC NAND support" 137 depends on CPU_ARM926EJS || CPU_ARM1136 || MX5 138 imply CMD_NAND 139 help 140 This enables the NAND driver for the NAND flash controller on the 141 i.MX27 / i.MX31 / i.MX5 rocessors. 142 143config NAND_MXS 144 bool "MXS NAND support" 145 depends on MX23 || MX28 || MX6 || MX7 146 select SYS_NAND_SELF_INIT 147 imply CMD_NAND 148 select APBH_DMA 149 select APBH_DMA_BURST if ARCH_MX6 || ARCH_MX7 150 select APBH_DMA_BURST8 if ARCH_MX6 || ARCH_MX7 151 help 152 This enables NAND driver for the NAND flash controller on the 153 MXS processors. 154 155config NAND_ZYNQ 156 bool "Support for Zynq Nand controller" 157 select SYS_NAND_SELF_INIT 158 imply CMD_NAND 159 help 160 This enables Nand driver support for Nand flash controller 161 found on Zynq SoC. 162 163config NAND_ZYNQ_USE_BOOTLOADER1_TIMINGS 164 bool "Enable use of 1st stage bootloader timing for NAND" 165 depends on NAND_ZYNQ 166 help 167 This flag prevent U-boot reconfigure NAND flash controller and reuse 168 the NAND timing from 1st stage bootloader. 169 170comment "Generic NAND options" 171 172config SYS_NAND_BLOCK_SIZE 173 hex "NAND chip eraseblock size" 174 depends on ARCH_SUNXI 175 help 176 Number of data bytes in one eraseblock for the NAND chip on the 177 board. This is the multiple of NAND_PAGE_SIZE and the number of 178 pages. 179 180config SYS_NAND_PAGE_SIZE 181 hex "NAND chip page size" 182 depends on ARCH_SUNXI 183 help 184 Number of data bytes in one page for the NAND chip on the 185 board, not including the OOB area. 186 187config SYS_NAND_OOBSIZE 188 hex "NAND chip OOB size" 189 depends on ARCH_SUNXI 190 help 191 Number of bytes in the Out-Of-Band area for the NAND chip on 192 the board. 193 194# Enhance depends when converting drivers to Kconfig which use this config 195# option (mxc_nand, ndfc, omap_gpmc). 196config SYS_NAND_BUSWIDTH_16BIT 197 bool "Use 16-bit NAND interface" 198 depends on NAND_VF610_NFC || NAND_OMAP_GPMC || NAND_MXC || ARCH_DAVINCI 199 help 200 Indicates that NAND device has 16-bit wide data-bus. In absence of this 201 config, bus-width of NAND device is assumed to be either 8-bit and later 202 determined by reading ONFI params. 203 Above config is useful when NAND device's bus-width information cannot 204 be determined from on-chip ONFI params, like in following scenarios: 205 - SPL boot does not support reading of ONFI parameters. This is done to 206 keep SPL code foot-print small. 207 - In current U-Boot flow using nand_init(), driver initialization 208 happens in board_nand_init() which is called before any device probe 209 (nand_scan_ident + nand_scan_tail), thus device's ONFI parameters are 210 not available while configuring controller. So a static CONFIG_NAND_xx 211 is needed to know the device's bus-width in advance. 212 213if SPL 214 215config SYS_NAND_U_BOOT_LOCATIONS 216 bool "Define U-boot binaries locations in NAND" 217 help 218 Enable CONFIG_SYS_NAND_U_BOOT_OFFS though Kconfig. 219 This option should not be enabled when compiling U-boot for boards 220 defining CONFIG_SYS_NAND_U_BOOT_OFFS in their include/configs/<board>.h 221 file. 222 223config SYS_NAND_U_BOOT_OFFS 224 hex "Location in NAND to read U-Boot from" 225 default 0x800000 if NAND_SUNXI 226 depends on SYS_NAND_U_BOOT_LOCATIONS 227 help 228 Set the offset from the start of the nand where u-boot should be 229 loaded from. 230 231config SYS_NAND_U_BOOT_OFFS_REDUND 232 hex "Location in NAND to read U-Boot from" 233 default SYS_NAND_U_BOOT_OFFS 234 depends on SYS_NAND_U_BOOT_LOCATIONS 235 help 236 Set the offset from the start of the nand where the redundant u-boot 237 should be loaded from. 238 239config SPL_NAND_AM33XX_BCH 240 bool "Enables SPL-NAND driver which supports ELM based" 241 depends on NAND_OMAP_GPMC && !OMAP34XX 242 default y 243 help 244 Hardware ECC correction. This is useful for platforms which have ELM 245 hardware engine and use NAND boot mode. 246 Some legacy platforms like OMAP3xx do not have in-built ELM h/w engine, 247 so those platforms should use CONFIG_SPL_NAND_SIMPLE for enabling 248 SPL-NAND driver with software ECC correction support. 249 250config SPL_NAND_DENALI 251 bool "Support Denali NAND controller for SPL" 252 help 253 This is a small implementation of the Denali NAND controller 254 for use on SPL. 255 256config SPL_NAND_SIMPLE 257 bool "Use simple SPL NAND driver" 258 depends on !SPL_NAND_AM33XX_BCH 259 help 260 Support for NAND boot using simple NAND drivers that 261 expose the cmd_ctrl() interface. 262endif 263 264endif # if NAND 265