1 /* 2 * (C) Copyright 2002-2004 3 * Brad Kemp, Seranoa Networks, Brad.Kemp@seranoa.com 4 * 5 * Copyright (C) 2003 Arabella Software Ltd. 6 * Yuli Barcohen <yuli@arabellasw.com> 7 * 8 * Copyright (C) 2004 9 * Ed Okerson 10 * 11 * Copyright (C) 2006 12 * Tolunay Orkun <listmember@orkun.us> 13 * 14 * See file CREDITS for list of people who contributed to this 15 * project. 16 * 17 * This program is free software; you can redistribute it and/or 18 * modify it under the terms of the GNU General Public License as 19 * published by the Free Software Foundation; either version 2 of 20 * the License, or (at your option) any later version. 21 * 22 * This program is distributed in the hope that it will be useful, 23 * but WITHOUT ANY WARRANTY; without even the implied warranty of 24 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 25 * GNU General Public License for more details. 26 * 27 * You should have received a copy of the GNU General Public License 28 * along with this program; if not, write to the Free Software 29 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, 30 * MA 02111-1307 USA 31 * 32 */ 33 34 /* The DEBUG define must be before common to enable debugging */ 35 /* #define DEBUG */ 36 37 #include <common.h> 38 #include <asm/processor.h> 39 #include <asm/io.h> 40 #include <asm/byteorder.h> 41 #include <environment.h> 42 43 /* 44 * This file implements a Common Flash Interface (CFI) driver for 45 * U-Boot. 46 * 47 * The width of the port and the width of the chips are determined at 48 * initialization. These widths are used to calculate the address for 49 * access CFI data structures. 50 * 51 * References 52 * JEDEC Standard JESD68 - Common Flash Interface (CFI) 53 * JEDEC Standard JEP137-A Common Flash Interface (CFI) ID Codes 54 * Intel Application Note 646 Common Flash Interface (CFI) and Command Sets 55 * Intel 290667-008 3 Volt Intel StrataFlash Memory datasheet 56 * AMD CFI Specification, Release 2.0 December 1, 2001 57 * AMD/Spansion Application Note: Migration from Single-byte to Three-byte 58 * Device IDs, Publication Number 25538 Revision A, November 8, 2001 59 * 60 * Define CONFIG_SYS_WRITE_SWAPPED_DATA, if you have to swap the Bytes between 61 * reading and writing ... (yes there is such a Hardware). 62 */ 63 64 #ifndef CONFIG_SYS_FLASH_BANKS_LIST 65 #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } 66 #endif 67 68 #define FLASH_CMD_CFI 0x98 69 #define FLASH_CMD_READ_ID 0x90 70 #define FLASH_CMD_RESET 0xff 71 #define FLASH_CMD_BLOCK_ERASE 0x20 72 #define FLASH_CMD_ERASE_CONFIRM 0xD0 73 #define FLASH_CMD_WRITE 0x40 74 #define FLASH_CMD_PROTECT 0x60 75 #define FLASH_CMD_PROTECT_SET 0x01 76 #define FLASH_CMD_PROTECT_CLEAR 0xD0 77 #define FLASH_CMD_CLEAR_STATUS 0x50 78 #define FLASH_CMD_READ_STATUS 0x70 79 #define FLASH_CMD_WRITE_TO_BUFFER 0xE8 80 #define FLASH_CMD_WRITE_BUFFER_PROG 0xE9 81 #define FLASH_CMD_WRITE_BUFFER_CONFIRM 0xD0 82 83 #define FLASH_STATUS_DONE 0x80 84 #define FLASH_STATUS_ESS 0x40 85 #define FLASH_STATUS_ECLBS 0x20 86 #define FLASH_STATUS_PSLBS 0x10 87 #define FLASH_STATUS_VPENS 0x08 88 #define FLASH_STATUS_PSS 0x04 89 #define FLASH_STATUS_DPS 0x02 90 #define FLASH_STATUS_R 0x01 91 #define FLASH_STATUS_PROTECT 0x01 92 93 #define AMD_CMD_RESET 0xF0 94 #define AMD_CMD_WRITE 0xA0 95 #define AMD_CMD_ERASE_START 0x80 96 #define AMD_CMD_ERASE_SECTOR 0x30 97 #define AMD_CMD_UNLOCK_START 0xAA 98 #define AMD_CMD_UNLOCK_ACK 0x55 99 #define AMD_CMD_WRITE_TO_BUFFER 0x25 100 #define AMD_CMD_WRITE_BUFFER_CONFIRM 0x29 101 102 #define AMD_STATUS_TOGGLE 0x40 103 #define AMD_STATUS_ERROR 0x20 104 105 #define ATM_CMD_UNLOCK_SECT 0x70 106 #define ATM_CMD_SOFTLOCK_START 0x80 107 #define ATM_CMD_LOCK_SECT 0x40 108 109 #define FLASH_OFFSET_MANUFACTURER_ID 0x00 110 #define FLASH_OFFSET_DEVICE_ID 0x01 111 #define FLASH_OFFSET_DEVICE_ID2 0x0E 112 #define FLASH_OFFSET_DEVICE_ID3 0x0F 113 #define FLASH_OFFSET_CFI 0x55 114 #define FLASH_OFFSET_CFI_ALT 0x555 115 #define FLASH_OFFSET_CFI_RESP 0x10 116 #define FLASH_OFFSET_PRIMARY_VENDOR 0x13 117 /* extended query table primary address */ 118 #define FLASH_OFFSET_EXT_QUERY_T_P_ADDR 0x15 119 #define FLASH_OFFSET_WTOUT 0x1F 120 #define FLASH_OFFSET_WBTOUT 0x20 121 #define FLASH_OFFSET_ETOUT 0x21 122 #define FLASH_OFFSET_CETOUT 0x22 123 #define FLASH_OFFSET_WMAX_TOUT 0x23 124 #define FLASH_OFFSET_WBMAX_TOUT 0x24 125 #define FLASH_OFFSET_EMAX_TOUT 0x25 126 #define FLASH_OFFSET_CEMAX_TOUT 0x26 127 #define FLASH_OFFSET_SIZE 0x27 128 #define FLASH_OFFSET_INTERFACE 0x28 129 #define FLASH_OFFSET_BUFFER_SIZE 0x2A 130 #define FLASH_OFFSET_NUM_ERASE_REGIONS 0x2C 131 #define FLASH_OFFSET_ERASE_REGIONS 0x2D 132 #define FLASH_OFFSET_PROTECT 0x02 133 #define FLASH_OFFSET_USER_PROTECTION 0x85 134 #define FLASH_OFFSET_INTEL_PROTECTION 0x81 135 136 #define CFI_CMDSET_NONE 0 137 #define CFI_CMDSET_INTEL_EXTENDED 1 138 #define CFI_CMDSET_AMD_STANDARD 2 139 #define CFI_CMDSET_INTEL_STANDARD 3 140 #define CFI_CMDSET_AMD_EXTENDED 4 141 #define CFI_CMDSET_MITSU_STANDARD 256 142 #define CFI_CMDSET_MITSU_EXTENDED 257 143 #define CFI_CMDSET_SST 258 144 #define CFI_CMDSET_INTEL_PROG_REGIONS 512 145 146 #ifdef CONFIG_SYS_FLASH_CFI_AMD_RESET /* needed for STM_ID_29W320DB on UC100 */ 147 # undef FLASH_CMD_RESET 148 # define FLASH_CMD_RESET AMD_CMD_RESET /* use AMD-Reset instead */ 149 #endif 150 151 typedef union { 152 unsigned char c; 153 unsigned short w; 154 unsigned long l; 155 unsigned long long ll; 156 } cfiword_t; 157 158 #define NUM_ERASE_REGIONS 4 /* max. number of erase regions */ 159 160 static uint flash_offset_cfi[2] = { FLASH_OFFSET_CFI, FLASH_OFFSET_CFI_ALT }; 161 static uint flash_verbose = 1; 162 163 /* use CONFIG_SYS_MAX_FLASH_BANKS_DETECT if defined */ 164 #ifdef CONFIG_SYS_MAX_FLASH_BANKS_DETECT 165 # define CFI_MAX_FLASH_BANKS CONFIG_SYS_MAX_FLASH_BANKS_DETECT 166 #else 167 # define CFI_MAX_FLASH_BANKS CONFIG_SYS_MAX_FLASH_BANKS 168 #endif 169 170 flash_info_t flash_info[CFI_MAX_FLASH_BANKS]; /* FLASH chips info */ 171 172 /* 173 * Check if chip width is defined. If not, start detecting with 8bit. 174 */ 175 #ifndef CONFIG_SYS_FLASH_CFI_WIDTH 176 #define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_8BIT 177 #endif 178 179 /* CFI standard query structure */ 180 struct cfi_qry { 181 u8 qry[3]; 182 u16 p_id; 183 u16 p_adr; 184 u16 a_id; 185 u16 a_adr; 186 u8 vcc_min; 187 u8 vcc_max; 188 u8 vpp_min; 189 u8 vpp_max; 190 u8 word_write_timeout_typ; 191 u8 buf_write_timeout_typ; 192 u8 block_erase_timeout_typ; 193 u8 chip_erase_timeout_typ; 194 u8 word_write_timeout_max; 195 u8 buf_write_timeout_max; 196 u8 block_erase_timeout_max; 197 u8 chip_erase_timeout_max; 198 u8 dev_size; 199 u16 interface_desc; 200 u16 max_buf_write_size; 201 u8 num_erase_regions; 202 u32 erase_region_info[NUM_ERASE_REGIONS]; 203 } __attribute__((packed)); 204 205 struct cfi_pri_hdr { 206 u8 pri[3]; 207 u8 major_version; 208 u8 minor_version; 209 } __attribute__((packed)); 210 211 static void __flash_write8(u8 value, void *addr) 212 { 213 __raw_writeb(value, addr); 214 } 215 216 static void __flash_write16(u16 value, void *addr) 217 { 218 __raw_writew(value, addr); 219 } 220 221 static void __flash_write32(u32 value, void *addr) 222 { 223 __raw_writel(value, addr); 224 } 225 226 static void __flash_write64(u64 value, void *addr) 227 { 228 /* No architectures currently implement __raw_writeq() */ 229 *(volatile u64 *)addr = value; 230 } 231 232 static u8 __flash_read8(void *addr) 233 { 234 return __raw_readb(addr); 235 } 236 237 static u16 __flash_read16(void *addr) 238 { 239 return __raw_readw(addr); 240 } 241 242 static u32 __flash_read32(void *addr) 243 { 244 return __raw_readl(addr); 245 } 246 247 static u64 __flash_read64(void *addr) 248 { 249 /* No architectures currently implement __raw_readq() */ 250 return *(volatile u64 *)addr; 251 } 252 253 #ifdef CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS 254 void flash_write8(u8 value, void *addr)__attribute__((weak, alias("__flash_write8"))); 255 void flash_write16(u16 value, void *addr)__attribute__((weak, alias("__flash_write16"))); 256 void flash_write32(u32 value, void *addr)__attribute__((weak, alias("__flash_write32"))); 257 void flash_write64(u64 value, void *addr)__attribute__((weak, alias("__flash_write64"))); 258 u8 flash_read8(void *addr)__attribute__((weak, alias("__flash_read8"))); 259 u16 flash_read16(void *addr)__attribute__((weak, alias("__flash_read16"))); 260 u32 flash_read32(void *addr)__attribute__((weak, alias("__flash_read32"))); 261 u64 flash_read64(void *addr)__attribute__((weak, alias("__flash_read64"))); 262 #else 263 #define flash_write8 __flash_write8 264 #define flash_write16 __flash_write16 265 #define flash_write32 __flash_write32 266 #define flash_write64 __flash_write64 267 #define flash_read8 __flash_read8 268 #define flash_read16 __flash_read16 269 #define flash_read32 __flash_read32 270 #define flash_read64 __flash_read64 271 #endif 272 273 /*----------------------------------------------------------------------- 274 */ 275 #if defined(CONFIG_ENV_IS_IN_FLASH) || defined(CONFIG_ENV_ADDR_REDUND) || (CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE) 276 flash_info_t *flash_get_info(ulong base) 277 { 278 int i; 279 flash_info_t * info = 0; 280 281 for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; i++) { 282 info = & flash_info[i]; 283 if (info->size && info->start[0] <= base && 284 base <= info->start[0] + info->size - 1) 285 break; 286 } 287 288 return i == CONFIG_SYS_MAX_FLASH_BANKS ? 0 : info; 289 } 290 #endif 291 292 unsigned long flash_sector_size(flash_info_t *info, flash_sect_t sect) 293 { 294 if (sect != (info->sector_count - 1)) 295 return info->start[sect + 1] - info->start[sect]; 296 else 297 return info->start[0] + info->size - info->start[sect]; 298 } 299 300 /*----------------------------------------------------------------------- 301 * create an address based on the offset and the port width 302 */ 303 static inline void * 304 flash_map (flash_info_t * info, flash_sect_t sect, uint offset) 305 { 306 unsigned int byte_offset = offset * info->portwidth; 307 308 return (void *)(info->start[sect] + byte_offset); 309 } 310 311 static inline void flash_unmap(flash_info_t *info, flash_sect_t sect, 312 unsigned int offset, void *addr) 313 { 314 } 315 316 /*----------------------------------------------------------------------- 317 * make a proper sized command based on the port and chip widths 318 */ 319 static void flash_make_cmd(flash_info_t *info, u32 cmd, void *cmdbuf) 320 { 321 int i; 322 int cword_offset; 323 int cp_offset; 324 #if defined(__LITTLE_ENDIAN) || defined(CONFIG_SYS_WRITE_SWAPPED_DATA) 325 u32 cmd_le = cpu_to_le32(cmd); 326 #endif 327 uchar val; 328 uchar *cp = (uchar *) cmdbuf; 329 330 for (i = info->portwidth; i > 0; i--){ 331 cword_offset = (info->portwidth-i)%info->chipwidth; 332 #if defined(__LITTLE_ENDIAN) || defined(CONFIG_SYS_WRITE_SWAPPED_DATA) 333 cp_offset = info->portwidth - i; 334 val = *((uchar*)&cmd_le + cword_offset); 335 #else 336 cp_offset = i - 1; 337 val = *((uchar*)&cmd + sizeof(u32) - cword_offset - 1); 338 #endif 339 cp[cp_offset] = (cword_offset >= sizeof(u32)) ? 0x00 : val; 340 } 341 } 342 343 #ifdef DEBUG 344 /*----------------------------------------------------------------------- 345 * Debug support 346 */ 347 static void print_longlong (char *str, unsigned long long data) 348 { 349 int i; 350 char *cp; 351 352 cp = (char *) &data; 353 for (i = 0; i < 8; i++) 354 sprintf (&str[i * 2], "%2.2x", *cp++); 355 } 356 357 static void flash_printqry (struct cfi_qry *qry) 358 { 359 u8 *p = (u8 *)qry; 360 int x, y; 361 362 for (x = 0; x < sizeof(struct cfi_qry); x += 16) { 363 debug("%02x : ", x); 364 for (y = 0; y < 16; y++) 365 debug("%2.2x ", p[x + y]); 366 debug(" "); 367 for (y = 0; y < 16; y++) { 368 unsigned char c = p[x + y]; 369 if (c >= 0x20 && c <= 0x7e) 370 debug("%c", c); 371 else 372 debug("."); 373 } 374 debug("\n"); 375 } 376 } 377 #endif 378 379 380 /*----------------------------------------------------------------------- 381 * read a character at a port width address 382 */ 383 static inline uchar flash_read_uchar (flash_info_t * info, uint offset) 384 { 385 uchar *cp; 386 uchar retval; 387 388 cp = flash_map (info, 0, offset); 389 #if defined(__LITTLE_ENDIAN) || defined(CONFIG_SYS_WRITE_SWAPPED_DATA) 390 retval = flash_read8(cp); 391 #else 392 retval = flash_read8(cp + info->portwidth - 1); 393 #endif 394 flash_unmap (info, 0, offset, cp); 395 return retval; 396 } 397 398 /*----------------------------------------------------------------------- 399 * read a word at a port width address, assume 16bit bus 400 */ 401 static inline ushort flash_read_word (flash_info_t * info, uint offset) 402 { 403 ushort *addr, retval; 404 405 addr = flash_map (info, 0, offset); 406 retval = flash_read16 (addr); 407 flash_unmap (info, 0, offset, addr); 408 return retval; 409 } 410 411 412 /*----------------------------------------------------------------------- 413 * read a long word by picking the least significant byte of each maximum 414 * port size word. Swap for ppc format. 415 */ 416 static ulong flash_read_long (flash_info_t * info, flash_sect_t sect, 417 uint offset) 418 { 419 uchar *addr; 420 ulong retval; 421 422 #ifdef DEBUG 423 int x; 424 #endif 425 addr = flash_map (info, sect, offset); 426 427 #ifdef DEBUG 428 debug ("long addr is at %p info->portwidth = %d\n", addr, 429 info->portwidth); 430 for (x = 0; x < 4 * info->portwidth; x++) { 431 debug ("addr[%x] = 0x%x\n", x, flash_read8(addr + x)); 432 } 433 #endif 434 #if defined(__LITTLE_ENDIAN) || defined(CONFIG_SYS_WRITE_SWAPPED_DATA) 435 retval = ((flash_read8(addr) << 16) | 436 (flash_read8(addr + info->portwidth) << 24) | 437 (flash_read8(addr + 2 * info->portwidth)) | 438 (flash_read8(addr + 3 * info->portwidth) << 8)); 439 #else 440 retval = ((flash_read8(addr + 2 * info->portwidth - 1) << 24) | 441 (flash_read8(addr + info->portwidth - 1) << 16) | 442 (flash_read8(addr + 4 * info->portwidth - 1) << 8) | 443 (flash_read8(addr + 3 * info->portwidth - 1))); 444 #endif 445 flash_unmap(info, sect, offset, addr); 446 447 return retval; 448 } 449 450 /* 451 * Write a proper sized command to the correct address 452 */ 453 static void flash_write_cmd (flash_info_t * info, flash_sect_t sect, 454 uint offset, u32 cmd) 455 { 456 457 void *addr; 458 cfiword_t cword; 459 460 addr = flash_map (info, sect, offset); 461 flash_make_cmd (info, cmd, &cword); 462 switch (info->portwidth) { 463 case FLASH_CFI_8BIT: 464 debug ("fwc addr %p cmd %x %x 8bit x %d bit\n", addr, cmd, 465 cword.c, info->chipwidth << CFI_FLASH_SHIFT_WIDTH); 466 flash_write8(cword.c, addr); 467 break; 468 case FLASH_CFI_16BIT: 469 debug ("fwc addr %p cmd %x %4.4x 16bit x %d bit\n", addr, 470 cmd, cword.w, 471 info->chipwidth << CFI_FLASH_SHIFT_WIDTH); 472 flash_write16(cword.w, addr); 473 break; 474 case FLASH_CFI_32BIT: 475 debug ("fwc addr %p cmd %x %8.8lx 32bit x %d bit\n", addr, 476 cmd, cword.l, 477 info->chipwidth << CFI_FLASH_SHIFT_WIDTH); 478 flash_write32(cword.l, addr); 479 break; 480 case FLASH_CFI_64BIT: 481 #ifdef DEBUG 482 { 483 char str[20]; 484 485 print_longlong (str, cword.ll); 486 487 debug ("fwrite addr %p cmd %x %s 64 bit x %d bit\n", 488 addr, cmd, str, 489 info->chipwidth << CFI_FLASH_SHIFT_WIDTH); 490 } 491 #endif 492 flash_write64(cword.ll, addr); 493 break; 494 } 495 496 /* Ensure all the instructions are fully finished */ 497 sync(); 498 499 flash_unmap(info, sect, offset, addr); 500 } 501 502 static void flash_unlock_seq (flash_info_t * info, flash_sect_t sect) 503 { 504 flash_write_cmd (info, sect, info->addr_unlock1, AMD_CMD_UNLOCK_START); 505 flash_write_cmd (info, sect, info->addr_unlock2, AMD_CMD_UNLOCK_ACK); 506 } 507 508 /*----------------------------------------------------------------------- 509 */ 510 static int flash_isequal (flash_info_t * info, flash_sect_t sect, 511 uint offset, uchar cmd) 512 { 513 void *addr; 514 cfiword_t cword; 515 int retval; 516 517 addr = flash_map (info, sect, offset); 518 flash_make_cmd (info, cmd, &cword); 519 520 debug ("is= cmd %x(%c) addr %p ", cmd, cmd, addr); 521 switch (info->portwidth) { 522 case FLASH_CFI_8BIT: 523 debug ("is= %x %x\n", flash_read8(addr), cword.c); 524 retval = (flash_read8(addr) == cword.c); 525 break; 526 case FLASH_CFI_16BIT: 527 debug ("is= %4.4x %4.4x\n", flash_read16(addr), cword.w); 528 retval = (flash_read16(addr) == cword.w); 529 break; 530 case FLASH_CFI_32BIT: 531 debug ("is= %8.8x %8.8lx\n", flash_read32(addr), cword.l); 532 retval = (flash_read32(addr) == cword.l); 533 break; 534 case FLASH_CFI_64BIT: 535 #ifdef DEBUG 536 { 537 char str1[20]; 538 char str2[20]; 539 540 print_longlong (str1, flash_read64(addr)); 541 print_longlong (str2, cword.ll); 542 debug ("is= %s %s\n", str1, str2); 543 } 544 #endif 545 retval = (flash_read64(addr) == cword.ll); 546 break; 547 default: 548 retval = 0; 549 break; 550 } 551 flash_unmap(info, sect, offset, addr); 552 553 return retval; 554 } 555 556 /*----------------------------------------------------------------------- 557 */ 558 static int flash_isset (flash_info_t * info, flash_sect_t sect, 559 uint offset, uchar cmd) 560 { 561 void *addr; 562 cfiword_t cword; 563 int retval; 564 565 addr = flash_map (info, sect, offset); 566 flash_make_cmd (info, cmd, &cword); 567 switch (info->portwidth) { 568 case FLASH_CFI_8BIT: 569 retval = ((flash_read8(addr) & cword.c) == cword.c); 570 break; 571 case FLASH_CFI_16BIT: 572 retval = ((flash_read16(addr) & cword.w) == cword.w); 573 break; 574 case FLASH_CFI_32BIT: 575 retval = ((flash_read32(addr) & cword.l) == cword.l); 576 break; 577 case FLASH_CFI_64BIT: 578 retval = ((flash_read64(addr) & cword.ll) == cword.ll); 579 break; 580 default: 581 retval = 0; 582 break; 583 } 584 flash_unmap(info, sect, offset, addr); 585 586 return retval; 587 } 588 589 /*----------------------------------------------------------------------- 590 */ 591 static int flash_toggle (flash_info_t * info, flash_sect_t sect, 592 uint offset, uchar cmd) 593 { 594 void *addr; 595 cfiword_t cword; 596 int retval; 597 598 addr = flash_map (info, sect, offset); 599 flash_make_cmd (info, cmd, &cword); 600 switch (info->portwidth) { 601 case FLASH_CFI_8BIT: 602 retval = flash_read8(addr) != flash_read8(addr); 603 break; 604 case FLASH_CFI_16BIT: 605 retval = flash_read16(addr) != flash_read16(addr); 606 break; 607 case FLASH_CFI_32BIT: 608 retval = flash_read32(addr) != flash_read32(addr); 609 break; 610 case FLASH_CFI_64BIT: 611 retval = ( (flash_read32( addr ) != flash_read32( addr )) || 612 (flash_read32(addr+4) != flash_read32(addr+4)) ); 613 break; 614 default: 615 retval = 0; 616 break; 617 } 618 flash_unmap(info, sect, offset, addr); 619 620 return retval; 621 } 622 623 /* 624 * flash_is_busy - check to see if the flash is busy 625 * 626 * This routine checks the status of the chip and returns true if the 627 * chip is busy. 628 */ 629 static int flash_is_busy (flash_info_t * info, flash_sect_t sect) 630 { 631 int retval; 632 633 switch (info->vendor) { 634 case CFI_CMDSET_INTEL_PROG_REGIONS: 635 case CFI_CMDSET_INTEL_STANDARD: 636 case CFI_CMDSET_INTEL_EXTENDED: 637 retval = !flash_isset (info, sect, 0, FLASH_STATUS_DONE); 638 break; 639 case CFI_CMDSET_AMD_STANDARD: 640 case CFI_CMDSET_AMD_EXTENDED: 641 #ifdef CONFIG_FLASH_CFI_LEGACY 642 case CFI_CMDSET_AMD_LEGACY: 643 #endif 644 retval = flash_toggle (info, sect, 0, AMD_STATUS_TOGGLE); 645 break; 646 default: 647 retval = 0; 648 } 649 debug ("flash_is_busy: %d\n", retval); 650 return retval; 651 } 652 653 /*----------------------------------------------------------------------- 654 * wait for XSR.7 to be set. Time out with an error if it does not. 655 * This routine does not set the flash to read-array mode. 656 */ 657 static int flash_status_check (flash_info_t * info, flash_sect_t sector, 658 ulong tout, char *prompt) 659 { 660 ulong start; 661 662 #if CONFIG_SYS_HZ != 1000 663 tout *= CONFIG_SYS_HZ/1000; 664 #endif 665 666 /* Wait for command completion */ 667 start = get_timer (0); 668 while (flash_is_busy (info, sector)) { 669 if (get_timer (start) > tout) { 670 printf ("Flash %s timeout at address %lx data %lx\n", 671 prompt, info->start[sector], 672 flash_read_long (info, sector, 0)); 673 flash_write_cmd (info, sector, 0, info->cmd_reset); 674 return ERR_TIMOUT; 675 } 676 udelay (1); /* also triggers watchdog */ 677 } 678 return ERR_OK; 679 } 680 681 /*----------------------------------------------------------------------- 682 * Wait for XSR.7 to be set, if it times out print an error, otherwise 683 * do a full status check. 684 * 685 * This routine sets the flash to read-array mode. 686 */ 687 static int flash_full_status_check (flash_info_t * info, flash_sect_t sector, 688 ulong tout, char *prompt) 689 { 690 int retcode; 691 692 retcode = flash_status_check (info, sector, tout, prompt); 693 switch (info->vendor) { 694 case CFI_CMDSET_INTEL_PROG_REGIONS: 695 case CFI_CMDSET_INTEL_EXTENDED: 696 case CFI_CMDSET_INTEL_STANDARD: 697 if ((retcode != ERR_OK) 698 && !flash_isequal (info, sector, 0, FLASH_STATUS_DONE)) { 699 retcode = ERR_INVAL; 700 printf ("Flash %s error at address %lx\n", prompt, 701 info->start[sector]); 702 if (flash_isset (info, sector, 0, FLASH_STATUS_ECLBS | 703 FLASH_STATUS_PSLBS)) { 704 puts ("Command Sequence Error.\n"); 705 } else if (flash_isset (info, sector, 0, 706 FLASH_STATUS_ECLBS)) { 707 puts ("Block Erase Error.\n"); 708 retcode = ERR_NOT_ERASED; 709 } else if (flash_isset (info, sector, 0, 710 FLASH_STATUS_PSLBS)) { 711 puts ("Locking Error\n"); 712 } 713 if (flash_isset (info, sector, 0, FLASH_STATUS_DPS)) { 714 puts ("Block locked.\n"); 715 retcode = ERR_PROTECTED; 716 } 717 if (flash_isset (info, sector, 0, FLASH_STATUS_VPENS)) 718 puts ("Vpp Low Error.\n"); 719 } 720 flash_write_cmd (info, sector, 0, info->cmd_reset); 721 break; 722 default: 723 break; 724 } 725 return retcode; 726 } 727 728 /*----------------------------------------------------------------------- 729 */ 730 static void flash_add_byte (flash_info_t * info, cfiword_t * cword, uchar c) 731 { 732 #if defined(__LITTLE_ENDIAN) && !defined(CONFIG_SYS_WRITE_SWAPPED_DATA) 733 unsigned short w; 734 unsigned int l; 735 unsigned long long ll; 736 #endif 737 738 switch (info->portwidth) { 739 case FLASH_CFI_8BIT: 740 cword->c = c; 741 break; 742 case FLASH_CFI_16BIT: 743 #if defined(__LITTLE_ENDIAN) && !defined(CONFIG_SYS_WRITE_SWAPPED_DATA) 744 w = c; 745 w <<= 8; 746 cword->w = (cword->w >> 8) | w; 747 #else 748 cword->w = (cword->w << 8) | c; 749 #endif 750 break; 751 case FLASH_CFI_32BIT: 752 #if defined(__LITTLE_ENDIAN) && !defined(CONFIG_SYS_WRITE_SWAPPED_DATA) 753 l = c; 754 l <<= 24; 755 cword->l = (cword->l >> 8) | l; 756 #else 757 cword->l = (cword->l << 8) | c; 758 #endif 759 break; 760 case FLASH_CFI_64BIT: 761 #if defined(__LITTLE_ENDIAN) && !defined(CONFIG_SYS_WRITE_SWAPPED_DATA) 762 ll = c; 763 ll <<= 56; 764 cword->ll = (cword->ll >> 8) | ll; 765 #else 766 cword->ll = (cword->ll << 8) | c; 767 #endif 768 break; 769 } 770 } 771 772 /* 773 * Loop through the sector table starting from the previously found sector. 774 * Searches forwards or backwards, dependent on the passed address. 775 */ 776 static flash_sect_t find_sector (flash_info_t * info, ulong addr) 777 { 778 static flash_sect_t saved_sector = 0; /* previously found sector */ 779 flash_sect_t sector = saved_sector; 780 781 while ((info->start[sector] < addr) 782 && (sector < info->sector_count - 1)) 783 sector++; 784 while ((info->start[sector] > addr) && (sector > 0)) 785 /* 786 * also decrements the sector in case of an overshot 787 * in the first loop 788 */ 789 sector--; 790 791 saved_sector = sector; 792 return sector; 793 } 794 795 /*----------------------------------------------------------------------- 796 */ 797 static int flash_write_cfiword (flash_info_t * info, ulong dest, 798 cfiword_t cword) 799 { 800 void *dstaddr = (void *)dest; 801 int flag; 802 flash_sect_t sect = 0; 803 char sect_found = 0; 804 805 /* Check if Flash is (sufficiently) erased */ 806 switch (info->portwidth) { 807 case FLASH_CFI_8BIT: 808 flag = ((flash_read8(dstaddr) & cword.c) == cword.c); 809 break; 810 case FLASH_CFI_16BIT: 811 flag = ((flash_read16(dstaddr) & cword.w) == cword.w); 812 break; 813 case FLASH_CFI_32BIT: 814 flag = ((flash_read32(dstaddr) & cword.l) == cword.l); 815 break; 816 case FLASH_CFI_64BIT: 817 flag = ((flash_read64(dstaddr) & cword.ll) == cword.ll); 818 break; 819 default: 820 flag = 0; 821 break; 822 } 823 if (!flag) 824 return ERR_NOT_ERASED; 825 826 /* Disable interrupts which might cause a timeout here */ 827 flag = disable_interrupts (); 828 829 switch (info->vendor) { 830 case CFI_CMDSET_INTEL_PROG_REGIONS: 831 case CFI_CMDSET_INTEL_EXTENDED: 832 case CFI_CMDSET_INTEL_STANDARD: 833 flash_write_cmd (info, 0, 0, FLASH_CMD_CLEAR_STATUS); 834 flash_write_cmd (info, 0, 0, FLASH_CMD_WRITE); 835 break; 836 case CFI_CMDSET_AMD_EXTENDED: 837 case CFI_CMDSET_AMD_STANDARD: 838 #ifdef CONFIG_FLASH_CFI_LEGACY 839 case CFI_CMDSET_AMD_LEGACY: 840 #endif 841 sect = find_sector(info, dest); 842 flash_unlock_seq (info, sect); 843 flash_write_cmd (info, sect, info->addr_unlock1, AMD_CMD_WRITE); 844 sect_found = 1; 845 break; 846 } 847 848 switch (info->portwidth) { 849 case FLASH_CFI_8BIT: 850 flash_write8(cword.c, dstaddr); 851 break; 852 case FLASH_CFI_16BIT: 853 flash_write16(cword.w, dstaddr); 854 break; 855 case FLASH_CFI_32BIT: 856 flash_write32(cword.l, dstaddr); 857 break; 858 case FLASH_CFI_64BIT: 859 flash_write64(cword.ll, dstaddr); 860 break; 861 } 862 863 /* re-enable interrupts if necessary */ 864 if (flag) 865 enable_interrupts (); 866 867 if (!sect_found) 868 sect = find_sector (info, dest); 869 870 return flash_full_status_check (info, sect, info->write_tout, "write"); 871 } 872 873 #ifdef CONFIG_SYS_FLASH_USE_BUFFER_WRITE 874 875 static int flash_write_cfibuffer (flash_info_t * info, ulong dest, uchar * cp, 876 int len) 877 { 878 flash_sect_t sector; 879 int cnt; 880 int retcode; 881 void *src = cp; 882 void *dst = (void *)dest; 883 void *dst2 = dst; 884 int flag = 0; 885 uint offset = 0; 886 unsigned int shift; 887 uchar write_cmd; 888 889 switch (info->portwidth) { 890 case FLASH_CFI_8BIT: 891 shift = 0; 892 break; 893 case FLASH_CFI_16BIT: 894 shift = 1; 895 break; 896 case FLASH_CFI_32BIT: 897 shift = 2; 898 break; 899 case FLASH_CFI_64BIT: 900 shift = 3; 901 break; 902 default: 903 retcode = ERR_INVAL; 904 goto out_unmap; 905 } 906 907 cnt = len >> shift; 908 909 while ((cnt-- > 0) && (flag == 0)) { 910 switch (info->portwidth) { 911 case FLASH_CFI_8BIT: 912 flag = ((flash_read8(dst2) & flash_read8(src)) == 913 flash_read8(src)); 914 src += 1, dst2 += 1; 915 break; 916 case FLASH_CFI_16BIT: 917 flag = ((flash_read16(dst2) & flash_read16(src)) == 918 flash_read16(src)); 919 src += 2, dst2 += 2; 920 break; 921 case FLASH_CFI_32BIT: 922 flag = ((flash_read32(dst2) & flash_read32(src)) == 923 flash_read32(src)); 924 src += 4, dst2 += 4; 925 break; 926 case FLASH_CFI_64BIT: 927 flag = ((flash_read64(dst2) & flash_read64(src)) == 928 flash_read64(src)); 929 src += 8, dst2 += 8; 930 break; 931 } 932 } 933 if (!flag) { 934 retcode = ERR_NOT_ERASED; 935 goto out_unmap; 936 } 937 938 src = cp; 939 sector = find_sector (info, dest); 940 941 switch (info->vendor) { 942 case CFI_CMDSET_INTEL_PROG_REGIONS: 943 case CFI_CMDSET_INTEL_STANDARD: 944 case CFI_CMDSET_INTEL_EXTENDED: 945 write_cmd = (info->vendor == CFI_CMDSET_INTEL_PROG_REGIONS) ? 946 FLASH_CMD_WRITE_BUFFER_PROG : FLASH_CMD_WRITE_TO_BUFFER; 947 flash_write_cmd (info, sector, 0, FLASH_CMD_CLEAR_STATUS); 948 flash_write_cmd (info, sector, 0, FLASH_CMD_READ_STATUS); 949 flash_write_cmd (info, sector, 0, write_cmd); 950 retcode = flash_status_check (info, sector, 951 info->buffer_write_tout, 952 "write to buffer"); 953 if (retcode == ERR_OK) { 954 /* reduce the number of loops by the width of 955 * the port */ 956 cnt = len >> shift; 957 flash_write_cmd (info, sector, 0, cnt - 1); 958 while (cnt-- > 0) { 959 switch (info->portwidth) { 960 case FLASH_CFI_8BIT: 961 flash_write8(flash_read8(src), dst); 962 src += 1, dst += 1; 963 break; 964 case FLASH_CFI_16BIT: 965 flash_write16(flash_read16(src), dst); 966 src += 2, dst += 2; 967 break; 968 case FLASH_CFI_32BIT: 969 flash_write32(flash_read32(src), dst); 970 src += 4, dst += 4; 971 break; 972 case FLASH_CFI_64BIT: 973 flash_write64(flash_read64(src), dst); 974 src += 8, dst += 8; 975 break; 976 default: 977 retcode = ERR_INVAL; 978 goto out_unmap; 979 } 980 } 981 flash_write_cmd (info, sector, 0, 982 FLASH_CMD_WRITE_BUFFER_CONFIRM); 983 retcode = flash_full_status_check ( 984 info, sector, info->buffer_write_tout, 985 "buffer write"); 986 } 987 988 break; 989 990 case CFI_CMDSET_AMD_STANDARD: 991 case CFI_CMDSET_AMD_EXTENDED: 992 flash_unlock_seq(info,0); 993 994 #ifdef CONFIG_FLASH_SPANSION_S29WS_N 995 offset = ((unsigned long)dst - info->start[sector]) >> shift; 996 #endif 997 flash_write_cmd(info, sector, offset, AMD_CMD_WRITE_TO_BUFFER); 998 cnt = len >> shift; 999 flash_write_cmd(info, sector, offset, (uchar)cnt - 1); 1000 1001 switch (info->portwidth) { 1002 case FLASH_CFI_8BIT: 1003 while (cnt-- > 0) { 1004 flash_write8(flash_read8(src), dst); 1005 src += 1, dst += 1; 1006 } 1007 break; 1008 case FLASH_CFI_16BIT: 1009 while (cnt-- > 0) { 1010 flash_write16(flash_read16(src), dst); 1011 src += 2, dst += 2; 1012 } 1013 break; 1014 case FLASH_CFI_32BIT: 1015 while (cnt-- > 0) { 1016 flash_write32(flash_read32(src), dst); 1017 src += 4, dst += 4; 1018 } 1019 break; 1020 case FLASH_CFI_64BIT: 1021 while (cnt-- > 0) { 1022 flash_write64(flash_read64(src), dst); 1023 src += 8, dst += 8; 1024 } 1025 break; 1026 default: 1027 retcode = ERR_INVAL; 1028 goto out_unmap; 1029 } 1030 1031 flash_write_cmd (info, sector, 0, AMD_CMD_WRITE_BUFFER_CONFIRM); 1032 retcode = flash_full_status_check (info, sector, 1033 info->buffer_write_tout, 1034 "buffer write"); 1035 break; 1036 1037 default: 1038 debug ("Unknown Command Set\n"); 1039 retcode = ERR_INVAL; 1040 break; 1041 } 1042 1043 out_unmap: 1044 return retcode; 1045 } 1046 #endif /* CONFIG_SYS_FLASH_USE_BUFFER_WRITE */ 1047 1048 1049 /*----------------------------------------------------------------------- 1050 */ 1051 int flash_erase (flash_info_t * info, int s_first, int s_last) 1052 { 1053 int rcode = 0; 1054 int prot; 1055 flash_sect_t sect; 1056 1057 if (info->flash_id != FLASH_MAN_CFI) { 1058 puts ("Can't erase unknown flash type - aborted\n"); 1059 return 1; 1060 } 1061 if ((s_first < 0) || (s_first > s_last)) { 1062 puts ("- no sectors to erase\n"); 1063 return 1; 1064 } 1065 1066 prot = 0; 1067 for (sect = s_first; sect <= s_last; ++sect) { 1068 if (info->protect[sect]) { 1069 prot++; 1070 } 1071 } 1072 if (prot) { 1073 printf ("- Warning: %d protected sectors will not be erased!\n", 1074 prot); 1075 } else if (flash_verbose) { 1076 putc ('\n'); 1077 } 1078 1079 1080 for (sect = s_first; sect <= s_last; sect++) { 1081 if (info->protect[sect] == 0) { /* not protected */ 1082 switch (info->vendor) { 1083 case CFI_CMDSET_INTEL_PROG_REGIONS: 1084 case CFI_CMDSET_INTEL_STANDARD: 1085 case CFI_CMDSET_INTEL_EXTENDED: 1086 flash_write_cmd (info, sect, 0, 1087 FLASH_CMD_CLEAR_STATUS); 1088 flash_write_cmd (info, sect, 0, 1089 FLASH_CMD_BLOCK_ERASE); 1090 flash_write_cmd (info, sect, 0, 1091 FLASH_CMD_ERASE_CONFIRM); 1092 break; 1093 case CFI_CMDSET_AMD_STANDARD: 1094 case CFI_CMDSET_AMD_EXTENDED: 1095 flash_unlock_seq (info, sect); 1096 flash_write_cmd (info, sect, 1097 info->addr_unlock1, 1098 AMD_CMD_ERASE_START); 1099 flash_unlock_seq (info, sect); 1100 flash_write_cmd (info, sect, 0, 1101 AMD_CMD_ERASE_SECTOR); 1102 break; 1103 #ifdef CONFIG_FLASH_CFI_LEGACY 1104 case CFI_CMDSET_AMD_LEGACY: 1105 flash_unlock_seq (info, 0); 1106 flash_write_cmd (info, 0, info->addr_unlock1, 1107 AMD_CMD_ERASE_START); 1108 flash_unlock_seq (info, 0); 1109 flash_write_cmd (info, sect, 0, 1110 AMD_CMD_ERASE_SECTOR); 1111 break; 1112 #endif 1113 default: 1114 debug ("Unkown flash vendor %d\n", 1115 info->vendor); 1116 break; 1117 } 1118 1119 if (flash_full_status_check 1120 (info, sect, info->erase_blk_tout, "erase")) { 1121 rcode = 1; 1122 } else if (flash_verbose) 1123 putc ('.'); 1124 } 1125 } 1126 1127 if (flash_verbose) 1128 puts (" done\n"); 1129 1130 return rcode; 1131 } 1132 1133 /*----------------------------------------------------------------------- 1134 */ 1135 void flash_print_info (flash_info_t * info) 1136 { 1137 int i; 1138 1139 if (info->flash_id != FLASH_MAN_CFI) { 1140 puts ("missing or unknown FLASH type\n"); 1141 return; 1142 } 1143 1144 printf ("%s FLASH (%d x %d)", 1145 info->name, 1146 (info->portwidth << 3), (info->chipwidth << 3)); 1147 if (info->size < 1024*1024) 1148 printf (" Size: %ld kB in %d Sectors\n", 1149 info->size >> 10, info->sector_count); 1150 else 1151 printf (" Size: %ld MB in %d Sectors\n", 1152 info->size >> 20, info->sector_count); 1153 printf (" "); 1154 switch (info->vendor) { 1155 case CFI_CMDSET_INTEL_PROG_REGIONS: 1156 printf ("Intel Prog Regions"); 1157 break; 1158 case CFI_CMDSET_INTEL_STANDARD: 1159 printf ("Intel Standard"); 1160 break; 1161 case CFI_CMDSET_INTEL_EXTENDED: 1162 printf ("Intel Extended"); 1163 break; 1164 case CFI_CMDSET_AMD_STANDARD: 1165 printf ("AMD Standard"); 1166 break; 1167 case CFI_CMDSET_AMD_EXTENDED: 1168 printf ("AMD Extended"); 1169 break; 1170 #ifdef CONFIG_FLASH_CFI_LEGACY 1171 case CFI_CMDSET_AMD_LEGACY: 1172 printf ("AMD Legacy"); 1173 break; 1174 #endif 1175 default: 1176 printf ("Unknown (%d)", info->vendor); 1177 break; 1178 } 1179 printf (" command set, Manufacturer ID: 0x%02X, Device ID: 0x%02X", 1180 info->manufacturer_id, info->device_id); 1181 if (info->device_id == 0x7E) { 1182 printf("%04X", info->device_id2); 1183 } 1184 printf ("\n Erase timeout: %ld ms, write timeout: %ld ms\n", 1185 info->erase_blk_tout, 1186 info->write_tout); 1187 if (info->buffer_size > 1) { 1188 printf (" Buffer write timeout: %ld ms, " 1189 "buffer size: %d bytes\n", 1190 info->buffer_write_tout, 1191 info->buffer_size); 1192 } 1193 1194 puts ("\n Sector Start Addresses:"); 1195 for (i = 0; i < info->sector_count; ++i) { 1196 if ((i % 5) == 0) 1197 printf ("\n"); 1198 #ifdef CONFIG_SYS_FLASH_EMPTY_INFO 1199 int k; 1200 int size; 1201 int erased; 1202 volatile unsigned long *flash; 1203 1204 /* 1205 * Check if whole sector is erased 1206 */ 1207 size = flash_sector_size(info, i); 1208 erased = 1; 1209 flash = (volatile unsigned long *) info->start[i]; 1210 size = size >> 2; /* divide by 4 for longword access */ 1211 for (k = 0; k < size; k++) { 1212 if (*flash++ != 0xffffffff) { 1213 erased = 0; 1214 break; 1215 } 1216 } 1217 1218 /* print empty and read-only info */ 1219 printf (" %08lX %c %s ", 1220 info->start[i], 1221 erased ? 'E' : ' ', 1222 info->protect[i] ? "RO" : " "); 1223 #else /* ! CONFIG_SYS_FLASH_EMPTY_INFO */ 1224 printf (" %08lX %s ", 1225 info->start[i], 1226 info->protect[i] ? "RO" : " "); 1227 #endif 1228 } 1229 putc ('\n'); 1230 return; 1231 } 1232 1233 /*----------------------------------------------------------------------- 1234 * This is used in a few places in write_buf() to show programming 1235 * progress. Making it a function is nasty because it needs to do side 1236 * effect updates to digit and dots. Repeated code is nasty too, so 1237 * we define it once here. 1238 */ 1239 #ifdef CONFIG_FLASH_SHOW_PROGRESS 1240 #define FLASH_SHOW_PROGRESS(scale, dots, digit, dots_sub) \ 1241 if (flash_verbose) { \ 1242 dots -= dots_sub; \ 1243 if ((scale > 0) && (dots <= 0)) { \ 1244 if ((digit % 5) == 0) \ 1245 printf ("%d", digit / 5); \ 1246 else \ 1247 putc ('.'); \ 1248 digit--; \ 1249 dots += scale; \ 1250 } \ 1251 } 1252 #else 1253 #define FLASH_SHOW_PROGRESS(scale, dots, digit, dots_sub) 1254 #endif 1255 1256 /*----------------------------------------------------------------------- 1257 * Copy memory to flash, returns: 1258 * 0 - OK 1259 * 1 - write timeout 1260 * 2 - Flash not erased 1261 */ 1262 int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt) 1263 { 1264 ulong wp; 1265 uchar *p; 1266 int aln; 1267 cfiword_t cword; 1268 int i, rc; 1269 #ifdef CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1270 int buffered_size; 1271 #endif 1272 #ifdef CONFIG_FLASH_SHOW_PROGRESS 1273 int digit = CONFIG_FLASH_SHOW_PROGRESS; 1274 int scale = 0; 1275 int dots = 0; 1276 1277 /* 1278 * Suppress if there are fewer than CONFIG_FLASH_SHOW_PROGRESS writes. 1279 */ 1280 if (cnt >= CONFIG_FLASH_SHOW_PROGRESS) { 1281 scale = (int)((cnt + CONFIG_FLASH_SHOW_PROGRESS - 1) / 1282 CONFIG_FLASH_SHOW_PROGRESS); 1283 } 1284 #endif 1285 1286 /* get lower aligned address */ 1287 wp = (addr & ~(info->portwidth - 1)); 1288 1289 /* handle unaligned start */ 1290 if ((aln = addr - wp) != 0) { 1291 cword.l = 0; 1292 p = (uchar *)wp; 1293 for (i = 0; i < aln; ++i) 1294 flash_add_byte (info, &cword, flash_read8(p + i)); 1295 1296 for (; (i < info->portwidth) && (cnt > 0); i++) { 1297 flash_add_byte (info, &cword, *src++); 1298 cnt--; 1299 } 1300 for (; (cnt == 0) && (i < info->portwidth); ++i) 1301 flash_add_byte (info, &cword, flash_read8(p + i)); 1302 1303 rc = flash_write_cfiword (info, wp, cword); 1304 if (rc != 0) 1305 return rc; 1306 1307 wp += i; 1308 FLASH_SHOW_PROGRESS(scale, dots, digit, i); 1309 } 1310 1311 /* handle the aligned part */ 1312 #ifdef CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1313 buffered_size = (info->portwidth / info->chipwidth); 1314 buffered_size *= info->buffer_size; 1315 while (cnt >= info->portwidth) { 1316 /* prohibit buffer write when buffer_size is 1 */ 1317 if (info->buffer_size == 1) { 1318 cword.l = 0; 1319 for (i = 0; i < info->portwidth; i++) 1320 flash_add_byte (info, &cword, *src++); 1321 if ((rc = flash_write_cfiword (info, wp, cword)) != 0) 1322 return rc; 1323 wp += info->portwidth; 1324 cnt -= info->portwidth; 1325 continue; 1326 } 1327 1328 /* write buffer until next buffered_size aligned boundary */ 1329 i = buffered_size - (wp % buffered_size); 1330 if (i > cnt) 1331 i = cnt; 1332 if ((rc = flash_write_cfibuffer (info, wp, src, i)) != ERR_OK) 1333 return rc; 1334 i -= i & (info->portwidth - 1); 1335 wp += i; 1336 src += i; 1337 cnt -= i; 1338 FLASH_SHOW_PROGRESS(scale, dots, digit, i); 1339 } 1340 #else 1341 while (cnt >= info->portwidth) { 1342 cword.l = 0; 1343 for (i = 0; i < info->portwidth; i++) { 1344 flash_add_byte (info, &cword, *src++); 1345 } 1346 if ((rc = flash_write_cfiword (info, wp, cword)) != 0) 1347 return rc; 1348 wp += info->portwidth; 1349 cnt -= info->portwidth; 1350 FLASH_SHOW_PROGRESS(scale, dots, digit, info->portwidth); 1351 } 1352 #endif /* CONFIG_SYS_FLASH_USE_BUFFER_WRITE */ 1353 1354 if (cnt == 0) { 1355 return (0); 1356 } 1357 1358 /* 1359 * handle unaligned tail bytes 1360 */ 1361 cword.l = 0; 1362 p = (uchar *)wp; 1363 for (i = 0; (i < info->portwidth) && (cnt > 0); ++i) { 1364 flash_add_byte (info, &cword, *src++); 1365 --cnt; 1366 } 1367 for (; i < info->portwidth; ++i) 1368 flash_add_byte (info, &cword, flash_read8(p + i)); 1369 1370 return flash_write_cfiword (info, wp, cword); 1371 } 1372 1373 /*----------------------------------------------------------------------- 1374 */ 1375 #ifdef CONFIG_SYS_FLASH_PROTECTION 1376 1377 int flash_real_protect (flash_info_t * info, long sector, int prot) 1378 { 1379 int retcode = 0; 1380 1381 switch (info->vendor) { 1382 case CFI_CMDSET_INTEL_PROG_REGIONS: 1383 case CFI_CMDSET_INTEL_STANDARD: 1384 case CFI_CMDSET_INTEL_EXTENDED: 1385 flash_write_cmd (info, sector, 0, 1386 FLASH_CMD_CLEAR_STATUS); 1387 flash_write_cmd (info, sector, 0, FLASH_CMD_PROTECT); 1388 if (prot) 1389 flash_write_cmd (info, sector, 0, 1390 FLASH_CMD_PROTECT_SET); 1391 else 1392 flash_write_cmd (info, sector, 0, 1393 FLASH_CMD_PROTECT_CLEAR); 1394 break; 1395 case CFI_CMDSET_AMD_EXTENDED: 1396 case CFI_CMDSET_AMD_STANDARD: 1397 /* U-Boot only checks the first byte */ 1398 if (info->manufacturer_id == (uchar)ATM_MANUFACT) { 1399 if (prot) { 1400 flash_unlock_seq (info, 0); 1401 flash_write_cmd (info, 0, 1402 info->addr_unlock1, 1403 ATM_CMD_SOFTLOCK_START); 1404 flash_unlock_seq (info, 0); 1405 flash_write_cmd (info, sector, 0, 1406 ATM_CMD_LOCK_SECT); 1407 } else { 1408 flash_write_cmd (info, 0, 1409 info->addr_unlock1, 1410 AMD_CMD_UNLOCK_START); 1411 if (info->device_id == ATM_ID_BV6416) 1412 flash_write_cmd (info, sector, 1413 0, ATM_CMD_UNLOCK_SECT); 1414 } 1415 } 1416 break; 1417 #ifdef CONFIG_FLASH_CFI_LEGACY 1418 case CFI_CMDSET_AMD_LEGACY: 1419 flash_write_cmd (info, sector, 0, FLASH_CMD_CLEAR_STATUS); 1420 flash_write_cmd (info, sector, 0, FLASH_CMD_PROTECT); 1421 if (prot) 1422 flash_write_cmd (info, sector, 0, FLASH_CMD_PROTECT_SET); 1423 else 1424 flash_write_cmd (info, sector, 0, FLASH_CMD_PROTECT_CLEAR); 1425 #endif 1426 }; 1427 1428 if ((retcode = 1429 flash_full_status_check (info, sector, info->erase_blk_tout, 1430 prot ? "protect" : "unprotect")) == 0) { 1431 1432 info->protect[sector] = prot; 1433 1434 /* 1435 * On some of Intel's flash chips (marked via legacy_unlock) 1436 * unprotect unprotects all locking. 1437 */ 1438 if ((prot == 0) && (info->legacy_unlock)) { 1439 flash_sect_t i; 1440 1441 for (i = 0; i < info->sector_count; i++) { 1442 if (info->protect[i]) 1443 flash_real_protect (info, i, 1); 1444 } 1445 } 1446 } 1447 return retcode; 1448 } 1449 1450 /*----------------------------------------------------------------------- 1451 * flash_read_user_serial - read the OneTimeProgramming cells 1452 */ 1453 void flash_read_user_serial (flash_info_t * info, void *buffer, int offset, 1454 int len) 1455 { 1456 uchar *src; 1457 uchar *dst; 1458 1459 dst = buffer; 1460 src = flash_map (info, 0, FLASH_OFFSET_USER_PROTECTION); 1461 flash_write_cmd (info, 0, 0, FLASH_CMD_READ_ID); 1462 memcpy (dst, src + offset, len); 1463 flash_write_cmd (info, 0, 0, info->cmd_reset); 1464 flash_unmap(info, 0, FLASH_OFFSET_USER_PROTECTION, src); 1465 } 1466 1467 /* 1468 * flash_read_factory_serial - read the device Id from the protection area 1469 */ 1470 void flash_read_factory_serial (flash_info_t * info, void *buffer, int offset, 1471 int len) 1472 { 1473 uchar *src; 1474 1475 src = flash_map (info, 0, FLASH_OFFSET_INTEL_PROTECTION); 1476 flash_write_cmd (info, 0, 0, FLASH_CMD_READ_ID); 1477 memcpy (buffer, src + offset, len); 1478 flash_write_cmd (info, 0, 0, info->cmd_reset); 1479 flash_unmap(info, 0, FLASH_OFFSET_INTEL_PROTECTION, src); 1480 } 1481 1482 #endif /* CONFIG_SYS_FLASH_PROTECTION */ 1483 1484 /*----------------------------------------------------------------------- 1485 * Reverse the order of the erase regions in the CFI QRY structure. 1486 * This is needed for chips that are either a) correctly detected as 1487 * top-boot, or b) buggy. 1488 */ 1489 static void cfi_reverse_geometry(struct cfi_qry *qry) 1490 { 1491 unsigned int i, j; 1492 u32 tmp; 1493 1494 for (i = 0, j = qry->num_erase_regions - 1; i < j; i++, j--) { 1495 tmp = qry->erase_region_info[i]; 1496 qry->erase_region_info[i] = qry->erase_region_info[j]; 1497 qry->erase_region_info[j] = tmp; 1498 } 1499 } 1500 1501 /*----------------------------------------------------------------------- 1502 * read jedec ids from device and set corresponding fields in info struct 1503 * 1504 * Note: assume cfi->vendor, cfi->portwidth and cfi->chipwidth are correct 1505 * 1506 */ 1507 static void cmdset_intel_read_jedec_ids(flash_info_t *info) 1508 { 1509 flash_write_cmd(info, 0, 0, FLASH_CMD_RESET); 1510 flash_write_cmd(info, 0, 0, FLASH_CMD_READ_ID); 1511 udelay(1000); /* some flash are slow to respond */ 1512 info->manufacturer_id = flash_read_uchar (info, 1513 FLASH_OFFSET_MANUFACTURER_ID); 1514 info->device_id = flash_read_uchar (info, 1515 FLASH_OFFSET_DEVICE_ID); 1516 flash_write_cmd(info, 0, 0, FLASH_CMD_RESET); 1517 } 1518 1519 static int cmdset_intel_init(flash_info_t *info, struct cfi_qry *qry) 1520 { 1521 info->cmd_reset = FLASH_CMD_RESET; 1522 1523 cmdset_intel_read_jedec_ids(info); 1524 flash_write_cmd(info, 0, info->cfi_offset, FLASH_CMD_CFI); 1525 1526 #ifdef CONFIG_SYS_FLASH_PROTECTION 1527 /* read legacy lock/unlock bit from intel flash */ 1528 if (info->ext_addr) { 1529 info->legacy_unlock = flash_read_uchar (info, 1530 info->ext_addr + 5) & 0x08; 1531 } 1532 #endif 1533 1534 return 0; 1535 } 1536 1537 static void cmdset_amd_read_jedec_ids(flash_info_t *info) 1538 { 1539 flash_write_cmd(info, 0, 0, AMD_CMD_RESET); 1540 flash_unlock_seq(info, 0); 1541 flash_write_cmd(info, 0, info->addr_unlock1, FLASH_CMD_READ_ID); 1542 udelay(1000); /* some flash are slow to respond */ 1543 1544 info->manufacturer_id = flash_read_uchar (info, 1545 FLASH_OFFSET_MANUFACTURER_ID); 1546 1547 switch (info->chipwidth){ 1548 case FLASH_CFI_8BIT: 1549 info->device_id = flash_read_uchar (info, 1550 FLASH_OFFSET_DEVICE_ID); 1551 if (info->device_id == 0x7E) { 1552 /* AMD 3-byte (expanded) device ids */ 1553 info->device_id2 = flash_read_uchar (info, 1554 FLASH_OFFSET_DEVICE_ID2); 1555 info->device_id2 <<= 8; 1556 info->device_id2 |= flash_read_uchar (info, 1557 FLASH_OFFSET_DEVICE_ID3); 1558 } 1559 break; 1560 case FLASH_CFI_16BIT: 1561 info->device_id = flash_read_word (info, 1562 FLASH_OFFSET_DEVICE_ID); 1563 break; 1564 default: 1565 break; 1566 } 1567 flash_write_cmd(info, 0, 0, AMD_CMD_RESET); 1568 } 1569 1570 static int cmdset_amd_init(flash_info_t *info, struct cfi_qry *qry) 1571 { 1572 info->cmd_reset = AMD_CMD_RESET; 1573 1574 cmdset_amd_read_jedec_ids(info); 1575 flash_write_cmd(info, 0, info->cfi_offset, FLASH_CMD_CFI); 1576 1577 return 0; 1578 } 1579 1580 #ifdef CONFIG_FLASH_CFI_LEGACY 1581 static void flash_read_jedec_ids (flash_info_t * info) 1582 { 1583 info->manufacturer_id = 0; 1584 info->device_id = 0; 1585 info->device_id2 = 0; 1586 1587 switch (info->vendor) { 1588 case CFI_CMDSET_INTEL_PROG_REGIONS: 1589 case CFI_CMDSET_INTEL_STANDARD: 1590 case CFI_CMDSET_INTEL_EXTENDED: 1591 cmdset_intel_read_jedec_ids(info); 1592 break; 1593 case CFI_CMDSET_AMD_STANDARD: 1594 case CFI_CMDSET_AMD_EXTENDED: 1595 cmdset_amd_read_jedec_ids(info); 1596 break; 1597 default: 1598 break; 1599 } 1600 } 1601 1602 /*----------------------------------------------------------------------- 1603 * Call board code to request info about non-CFI flash. 1604 * board_flash_get_legacy needs to fill in at least: 1605 * info->portwidth, info->chipwidth and info->interface for Jedec probing. 1606 */ 1607 static int flash_detect_legacy(phys_addr_t base, int banknum) 1608 { 1609 flash_info_t *info = &flash_info[banknum]; 1610 1611 if (board_flash_get_legacy(base, banknum, info)) { 1612 /* board code may have filled info completely. If not, we 1613 use JEDEC ID probing. */ 1614 if (!info->vendor) { 1615 int modes[] = { 1616 CFI_CMDSET_AMD_STANDARD, 1617 CFI_CMDSET_INTEL_STANDARD 1618 }; 1619 int i; 1620 1621 for (i = 0; i < sizeof(modes) / sizeof(modes[0]); i++) { 1622 info->vendor = modes[i]; 1623 info->start[0] = 1624 (ulong)map_physmem(base, 1625 info->portwidth, 1626 MAP_NOCACHE); 1627 if (info->portwidth == FLASH_CFI_8BIT 1628 && info->interface == FLASH_CFI_X8X16) { 1629 info->addr_unlock1 = 0x2AAA; 1630 info->addr_unlock2 = 0x5555; 1631 } else { 1632 info->addr_unlock1 = 0x5555; 1633 info->addr_unlock2 = 0x2AAA; 1634 } 1635 flash_read_jedec_ids(info); 1636 debug("JEDEC PROBE: ID %x %x %x\n", 1637 info->manufacturer_id, 1638 info->device_id, 1639 info->device_id2); 1640 if (jedec_flash_match(info, info->start[0])) 1641 break; 1642 else 1643 unmap_physmem((void *)info->start[0], 1644 MAP_NOCACHE); 1645 } 1646 } 1647 1648 switch(info->vendor) { 1649 case CFI_CMDSET_INTEL_PROG_REGIONS: 1650 case CFI_CMDSET_INTEL_STANDARD: 1651 case CFI_CMDSET_INTEL_EXTENDED: 1652 info->cmd_reset = FLASH_CMD_RESET; 1653 break; 1654 case CFI_CMDSET_AMD_STANDARD: 1655 case CFI_CMDSET_AMD_EXTENDED: 1656 case CFI_CMDSET_AMD_LEGACY: 1657 info->cmd_reset = AMD_CMD_RESET; 1658 break; 1659 } 1660 info->flash_id = FLASH_MAN_CFI; 1661 return 1; 1662 } 1663 return 0; /* use CFI */ 1664 } 1665 #else 1666 static inline int flash_detect_legacy(phys_addr_t base, int banknum) 1667 { 1668 return 0; /* use CFI */ 1669 } 1670 #endif 1671 1672 /*----------------------------------------------------------------------- 1673 * detect if flash is compatible with the Common Flash Interface (CFI) 1674 * http://www.jedec.org/download/search/jesd68.pdf 1675 */ 1676 static void flash_read_cfi (flash_info_t *info, void *buf, 1677 unsigned int start, size_t len) 1678 { 1679 u8 *p = buf; 1680 unsigned int i; 1681 1682 for (i = 0; i < len; i++) 1683 p[i] = flash_read_uchar(info, start + i); 1684 } 1685 1686 static int __flash_detect_cfi (flash_info_t * info, struct cfi_qry *qry) 1687 { 1688 int cfi_offset; 1689 1690 /* We do not yet know what kind of commandset to use, so we issue 1691 the reset command in both Intel and AMD variants, in the hope 1692 that AMD flash roms ignore the Intel command. */ 1693 flash_write_cmd (info, 0, 0, AMD_CMD_RESET); 1694 flash_write_cmd (info, 0, 0, FLASH_CMD_RESET); 1695 1696 for (cfi_offset=0; 1697 cfi_offset < sizeof(flash_offset_cfi) / sizeof(uint); 1698 cfi_offset++) { 1699 flash_write_cmd (info, 0, flash_offset_cfi[cfi_offset], 1700 FLASH_CMD_CFI); 1701 if (flash_isequal (info, 0, FLASH_OFFSET_CFI_RESP, 'Q') 1702 && flash_isequal (info, 0, FLASH_OFFSET_CFI_RESP + 1, 'R') 1703 && flash_isequal (info, 0, FLASH_OFFSET_CFI_RESP + 2, 'Y')) { 1704 flash_read_cfi(info, qry, FLASH_OFFSET_CFI_RESP, 1705 sizeof(struct cfi_qry)); 1706 info->interface = le16_to_cpu(qry->interface_desc); 1707 1708 info->cfi_offset = flash_offset_cfi[cfi_offset]; 1709 debug ("device interface is %d\n", 1710 info->interface); 1711 debug ("found port %d chip %d ", 1712 info->portwidth, info->chipwidth); 1713 debug ("port %d bits chip %d bits\n", 1714 info->portwidth << CFI_FLASH_SHIFT_WIDTH, 1715 info->chipwidth << CFI_FLASH_SHIFT_WIDTH); 1716 1717 /* calculate command offsets as in the Linux driver */ 1718 info->addr_unlock1 = 0x555; 1719 info->addr_unlock2 = 0x2aa; 1720 1721 /* 1722 * modify the unlock address if we are 1723 * in compatibility mode 1724 */ 1725 if ( /* x8/x16 in x8 mode */ 1726 ((info->chipwidth == FLASH_CFI_BY8) && 1727 (info->interface == FLASH_CFI_X8X16)) || 1728 /* x16/x32 in x16 mode */ 1729 ((info->chipwidth == FLASH_CFI_BY16) && 1730 (info->interface == FLASH_CFI_X16X32))) 1731 { 1732 info->addr_unlock1 = 0xaaa; 1733 info->addr_unlock2 = 0x555; 1734 } 1735 1736 info->name = "CFI conformant"; 1737 return 1; 1738 } 1739 } 1740 1741 return 0; 1742 } 1743 1744 static int flash_detect_cfi (flash_info_t * info, struct cfi_qry *qry) 1745 { 1746 debug ("flash detect cfi\n"); 1747 1748 for (info->portwidth = CONFIG_SYS_FLASH_CFI_WIDTH; 1749 info->portwidth <= FLASH_CFI_64BIT; info->portwidth <<= 1) { 1750 for (info->chipwidth = FLASH_CFI_BY8; 1751 info->chipwidth <= info->portwidth; 1752 info->chipwidth <<= 1) 1753 if (__flash_detect_cfi(info, qry)) 1754 return 1; 1755 } 1756 debug ("not found\n"); 1757 return 0; 1758 } 1759 1760 /* 1761 * Manufacturer-specific quirks. Add workarounds for geometry 1762 * reversal, etc. here. 1763 */ 1764 static void flash_fixup_amd(flash_info_t *info, struct cfi_qry *qry) 1765 { 1766 /* check if flash geometry needs reversal */ 1767 if (qry->num_erase_regions > 1) { 1768 /* reverse geometry if top boot part */ 1769 if (info->cfi_version < 0x3131) { 1770 /* CFI < 1.1, try to guess from device id */ 1771 if ((info->device_id & 0x80) != 0) 1772 cfi_reverse_geometry(qry); 1773 } else if (flash_read_uchar(info, info->ext_addr + 0xf) == 3) { 1774 /* CFI >= 1.1, deduct from top/bottom flag */ 1775 /* note: ext_addr is valid since cfi_version > 0 */ 1776 cfi_reverse_geometry(qry); 1777 } 1778 } 1779 } 1780 1781 static void flash_fixup_atmel(flash_info_t *info, struct cfi_qry *qry) 1782 { 1783 int reverse_geometry = 0; 1784 1785 /* Check the "top boot" bit in the PRI */ 1786 if (info->ext_addr && !(flash_read_uchar(info, info->ext_addr + 6) & 1)) 1787 reverse_geometry = 1; 1788 1789 /* AT49BV6416(T) list the erase regions in the wrong order. 1790 * However, the device ID is identical with the non-broken 1791 * AT49BV642D they differ in the high byte. 1792 */ 1793 if (info->device_id == 0xd6 || info->device_id == 0xd2) 1794 reverse_geometry = !reverse_geometry; 1795 1796 if (reverse_geometry) 1797 cfi_reverse_geometry(qry); 1798 } 1799 1800 static void flash_fixup_stm(flash_info_t *info, struct cfi_qry *qry) 1801 { 1802 /* check if flash geometry needs reversal */ 1803 if (qry->num_erase_regions > 1) { 1804 /* reverse geometry if top boot part */ 1805 if (info->cfi_version < 0x3131) { 1806 /* CFI < 1.1, guess by device id (M29W320{DT,ET} only) */ 1807 if (info->device_id == 0x22CA || 1808 info->device_id == 0x2256) { 1809 cfi_reverse_geometry(qry); 1810 } 1811 } 1812 } 1813 } 1814 1815 /* 1816 * The following code cannot be run from FLASH! 1817 * 1818 */ 1819 ulong flash_get_size (phys_addr_t base, int banknum) 1820 { 1821 flash_info_t *info = &flash_info[banknum]; 1822 int i, j; 1823 flash_sect_t sect_cnt; 1824 phys_addr_t sector; 1825 unsigned long tmp; 1826 int size_ratio; 1827 uchar num_erase_regions; 1828 int erase_region_size; 1829 int erase_region_count; 1830 struct cfi_qry qry; 1831 1832 memset(&qry, 0, sizeof(qry)); 1833 1834 info->ext_addr = 0; 1835 info->cfi_version = 0; 1836 #ifdef CONFIG_SYS_FLASH_PROTECTION 1837 info->legacy_unlock = 0; 1838 #endif 1839 1840 info->start[0] = (ulong)map_physmem(base, info->portwidth, MAP_NOCACHE); 1841 1842 if (flash_detect_cfi (info, &qry)) { 1843 info->vendor = le16_to_cpu(qry.p_id); 1844 info->ext_addr = le16_to_cpu(qry.p_adr); 1845 num_erase_regions = qry.num_erase_regions; 1846 1847 if (info->ext_addr) { 1848 info->cfi_version = (ushort) flash_read_uchar (info, 1849 info->ext_addr + 3) << 8; 1850 info->cfi_version |= (ushort) flash_read_uchar (info, 1851 info->ext_addr + 4); 1852 } 1853 1854 #ifdef DEBUG 1855 flash_printqry (&qry); 1856 #endif 1857 1858 switch (info->vendor) { 1859 case CFI_CMDSET_INTEL_PROG_REGIONS: 1860 case CFI_CMDSET_INTEL_STANDARD: 1861 case CFI_CMDSET_INTEL_EXTENDED: 1862 cmdset_intel_init(info, &qry); 1863 break; 1864 case CFI_CMDSET_AMD_STANDARD: 1865 case CFI_CMDSET_AMD_EXTENDED: 1866 cmdset_amd_init(info, &qry); 1867 break; 1868 default: 1869 printf("CFI: Unknown command set 0x%x\n", 1870 info->vendor); 1871 /* 1872 * Unfortunately, this means we don't know how 1873 * to get the chip back to Read mode. Might 1874 * as well try an Intel-style reset... 1875 */ 1876 flash_write_cmd(info, 0, 0, FLASH_CMD_RESET); 1877 return 0; 1878 } 1879 1880 /* Do manufacturer-specific fixups */ 1881 switch (info->manufacturer_id) { 1882 case 0x0001: 1883 flash_fixup_amd(info, &qry); 1884 break; 1885 case 0x001f: 1886 flash_fixup_atmel(info, &qry); 1887 break; 1888 case 0x0020: 1889 flash_fixup_stm(info, &qry); 1890 break; 1891 } 1892 1893 debug ("manufacturer is %d\n", info->vendor); 1894 debug ("manufacturer id is 0x%x\n", info->manufacturer_id); 1895 debug ("device id is 0x%x\n", info->device_id); 1896 debug ("device id2 is 0x%x\n", info->device_id2); 1897 debug ("cfi version is 0x%04x\n", info->cfi_version); 1898 1899 size_ratio = info->portwidth / info->chipwidth; 1900 /* if the chip is x8/x16 reduce the ratio by half */ 1901 if ((info->interface == FLASH_CFI_X8X16) 1902 && (info->chipwidth == FLASH_CFI_BY8)) { 1903 size_ratio >>= 1; 1904 } 1905 debug ("size_ratio %d port %d bits chip %d bits\n", 1906 size_ratio, info->portwidth << CFI_FLASH_SHIFT_WIDTH, 1907 info->chipwidth << CFI_FLASH_SHIFT_WIDTH); 1908 debug ("found %d erase regions\n", num_erase_regions); 1909 sect_cnt = 0; 1910 sector = base; 1911 for (i = 0; i < num_erase_regions; i++) { 1912 if (i > NUM_ERASE_REGIONS) { 1913 printf ("%d erase regions found, only %d used\n", 1914 num_erase_regions, NUM_ERASE_REGIONS); 1915 break; 1916 } 1917 1918 tmp = le32_to_cpu(qry.erase_region_info[i]); 1919 debug("erase region %u: 0x%08lx\n", i, tmp); 1920 1921 erase_region_count = (tmp & 0xffff) + 1; 1922 tmp >>= 16; 1923 erase_region_size = 1924 (tmp & 0xffff) ? ((tmp & 0xffff) * 256) : 128; 1925 debug ("erase_region_count = %d erase_region_size = %d\n", 1926 erase_region_count, erase_region_size); 1927 for (j = 0; j < erase_region_count; j++) { 1928 if (sect_cnt >= CONFIG_SYS_MAX_FLASH_SECT) { 1929 printf("ERROR: too many flash sectors\n"); 1930 break; 1931 } 1932 info->start[sect_cnt] = 1933 (ulong)map_physmem(sector, 1934 info->portwidth, 1935 MAP_NOCACHE); 1936 sector += (erase_region_size * size_ratio); 1937 1938 /* 1939 * Only read protection status from 1940 * supported devices (intel...) 1941 */ 1942 switch (info->vendor) { 1943 case CFI_CMDSET_INTEL_PROG_REGIONS: 1944 case CFI_CMDSET_INTEL_EXTENDED: 1945 case CFI_CMDSET_INTEL_STANDARD: 1946 info->protect[sect_cnt] = 1947 flash_isset (info, sect_cnt, 1948 FLASH_OFFSET_PROTECT, 1949 FLASH_STATUS_PROTECT); 1950 break; 1951 default: 1952 /* default: not protected */ 1953 info->protect[sect_cnt] = 0; 1954 } 1955 1956 sect_cnt++; 1957 } 1958 } 1959 1960 info->sector_count = sect_cnt; 1961 info->size = 1 << qry.dev_size; 1962 /* multiply the size by the number of chips */ 1963 info->size *= size_ratio; 1964 info->buffer_size = 1 << le16_to_cpu(qry.max_buf_write_size); 1965 tmp = 1 << qry.block_erase_timeout_typ; 1966 info->erase_blk_tout = tmp * 1967 (1 << qry.block_erase_timeout_max); 1968 tmp = (1 << qry.buf_write_timeout_typ) * 1969 (1 << qry.buf_write_timeout_max); 1970 1971 /* round up when converting to ms */ 1972 info->buffer_write_tout = (tmp + 999) / 1000; 1973 tmp = (1 << qry.word_write_timeout_typ) * 1974 (1 << qry.word_write_timeout_max); 1975 /* round up when converting to ms */ 1976 info->write_tout = (tmp + 999) / 1000; 1977 info->flash_id = FLASH_MAN_CFI; 1978 if ((info->interface == FLASH_CFI_X8X16) && 1979 (info->chipwidth == FLASH_CFI_BY8)) { 1980 /* XXX - Need to test on x8/x16 in parallel. */ 1981 info->portwidth >>= 1; 1982 } 1983 1984 flash_write_cmd (info, 0, 0, info->cmd_reset); 1985 } 1986 1987 return (info->size); 1988 } 1989 1990 void flash_set_verbose(uint v) 1991 { 1992 flash_verbose = v; 1993 } 1994 1995 /*----------------------------------------------------------------------- 1996 */ 1997 unsigned long flash_init (void) 1998 { 1999 unsigned long size = 0; 2000 int i; 2001 #if defined(CONFIG_SYS_FLASH_AUTOPROTECT_LIST) 2002 struct apl_s { 2003 ulong start; 2004 ulong size; 2005 } apl[] = CONFIG_SYS_FLASH_AUTOPROTECT_LIST; 2006 #endif 2007 2008 #ifdef CONFIG_SYS_FLASH_PROTECTION 2009 /* read environment from EEPROM */ 2010 char s[64]; 2011 getenv_r ("unlock", s, sizeof(s)); 2012 #endif 2013 2014 #define BANK_BASE(i) (((phys_addr_t [CFI_MAX_FLASH_BANKS])CONFIG_SYS_FLASH_BANKS_LIST)[i]) 2015 2016 /* Init: no FLASHes known */ 2017 for (i = 0; i < CONFIG_SYS_MAX_FLASH_BANKS; ++i) { 2018 flash_info[i].flash_id = FLASH_UNKNOWN; 2019 2020 if (!flash_detect_legacy (BANK_BASE(i), i)) 2021 flash_get_size (BANK_BASE(i), i); 2022 size += flash_info[i].size; 2023 if (flash_info[i].flash_id == FLASH_UNKNOWN) { 2024 #ifndef CONFIG_SYS_FLASH_QUIET_TEST 2025 printf ("## Unknown FLASH on Bank %d " 2026 "- Size = 0x%08lx = %ld MB\n", 2027 i+1, flash_info[i].size, 2028 flash_info[i].size << 20); 2029 #endif /* CONFIG_SYS_FLASH_QUIET_TEST */ 2030 } 2031 #ifdef CONFIG_SYS_FLASH_PROTECTION 2032 else if ((s != NULL) && (strcmp(s, "yes") == 0)) { 2033 /* 2034 * Only the U-Boot image and it's environment 2035 * is protected, all other sectors are 2036 * unprotected (unlocked) if flash hardware 2037 * protection is used (CONFIG_SYS_FLASH_PROTECTION) 2038 * and the environment variable "unlock" is 2039 * set to "yes". 2040 */ 2041 if (flash_info[i].legacy_unlock) { 2042 int k; 2043 2044 /* 2045 * Disable legacy_unlock temporarily, 2046 * since flash_real_protect would 2047 * relock all other sectors again 2048 * otherwise. 2049 */ 2050 flash_info[i].legacy_unlock = 0; 2051 2052 /* 2053 * Legacy unlocking (e.g. Intel J3) -> 2054 * unlock only one sector. This will 2055 * unlock all sectors. 2056 */ 2057 flash_real_protect (&flash_info[i], 0, 0); 2058 2059 flash_info[i].legacy_unlock = 1; 2060 2061 /* 2062 * Manually mark other sectors as 2063 * unlocked (unprotected) 2064 */ 2065 for (k = 1; k < flash_info[i].sector_count; k++) 2066 flash_info[i].protect[k] = 0; 2067 } else { 2068 /* 2069 * No legancy unlocking -> unlock all sectors 2070 */ 2071 flash_protect (FLAG_PROTECT_CLEAR, 2072 flash_info[i].start[0], 2073 flash_info[i].start[0] 2074 + flash_info[i].size - 1, 2075 &flash_info[i]); 2076 } 2077 } 2078 #endif /* CONFIG_SYS_FLASH_PROTECTION */ 2079 } 2080 2081 /* Monitor protection ON by default */ 2082 #if (CONFIG_SYS_MONITOR_BASE >= CONFIG_SYS_FLASH_BASE) 2083 flash_protect (FLAG_PROTECT_SET, 2084 CONFIG_SYS_MONITOR_BASE, 2085 CONFIG_SYS_MONITOR_BASE + monitor_flash_len - 1, 2086 flash_get_info(CONFIG_SYS_MONITOR_BASE)); 2087 #endif 2088 2089 /* Environment protection ON by default */ 2090 #ifdef CONFIG_ENV_IS_IN_FLASH 2091 flash_protect (FLAG_PROTECT_SET, 2092 CONFIG_ENV_ADDR, 2093 CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE - 1, 2094 flash_get_info(CONFIG_ENV_ADDR)); 2095 #endif 2096 2097 /* Redundant environment protection ON by default */ 2098 #ifdef CONFIG_ENV_ADDR_REDUND 2099 flash_protect (FLAG_PROTECT_SET, 2100 CONFIG_ENV_ADDR_REDUND, 2101 CONFIG_ENV_ADDR_REDUND + CONFIG_ENV_SECT_SIZE - 1, 2102 flash_get_info(CONFIG_ENV_ADDR_REDUND)); 2103 #endif 2104 2105 #if defined(CONFIG_SYS_FLASH_AUTOPROTECT_LIST) 2106 for (i = 0; i < (sizeof(apl) / sizeof(struct apl_s)); i++) { 2107 debug("autoprotecting from %08x to %08x\n", 2108 apl[i].start, apl[i].start + apl[i].size - 1); 2109 flash_protect (FLAG_PROTECT_SET, 2110 apl[i].start, 2111 apl[i].start + apl[i].size - 1, 2112 flash_get_info(apl[i].start)); 2113 } 2114 #endif 2115 2116 #ifdef CONFIG_FLASH_CFI_MTD 2117 cfi_mtd_init(); 2118 #endif 2119 2120 return (size); 2121 } 2122