1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * Copyright 2007, 2010-2011 Freescale Semiconductor, Inc 4 * Andy Fleming 5 * 6 * Based vaguely on the pxa mmc code: 7 * (C) Copyright 2003 8 * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net 9 */ 10 11 #include <config.h> 12 #include <common.h> 13 #include <command.h> 14 #include <clk.h> 15 #include <errno.h> 16 #include <hwconfig.h> 17 #include <mmc.h> 18 #include <part.h> 19 #include <power/regulator.h> 20 #include <malloc.h> 21 #include <fsl_esdhc.h> 22 #include <fdt_support.h> 23 #include <asm/io.h> 24 #include <dm.h> 25 #include <asm-generic/gpio.h> 26 #include <dm/pinctrl.h> 27 28 DECLARE_GLOBAL_DATA_PTR; 29 30 #define SDHCI_IRQ_EN_BITS (IRQSTATEN_CC | IRQSTATEN_TC | \ 31 IRQSTATEN_CINT | \ 32 IRQSTATEN_CTOE | IRQSTATEN_CCE | IRQSTATEN_CEBE | \ 33 IRQSTATEN_CIE | IRQSTATEN_DTOE | IRQSTATEN_DCE | \ 34 IRQSTATEN_DEBE | IRQSTATEN_BRR | IRQSTATEN_BWR | \ 35 IRQSTATEN_DINT) 36 #define MAX_TUNING_LOOP 40 37 38 struct fsl_esdhc { 39 uint dsaddr; /* SDMA system address register */ 40 uint blkattr; /* Block attributes register */ 41 uint cmdarg; /* Command argument register */ 42 uint xfertyp; /* Transfer type register */ 43 uint cmdrsp0; /* Command response 0 register */ 44 uint cmdrsp1; /* Command response 1 register */ 45 uint cmdrsp2; /* Command response 2 register */ 46 uint cmdrsp3; /* Command response 3 register */ 47 uint datport; /* Buffer data port register */ 48 uint prsstat; /* Present state register */ 49 uint proctl; /* Protocol control register */ 50 uint sysctl; /* System Control Register */ 51 uint irqstat; /* Interrupt status register */ 52 uint irqstaten; /* Interrupt status enable register */ 53 uint irqsigen; /* Interrupt signal enable register */ 54 uint autoc12err; /* Auto CMD error status register */ 55 uint hostcapblt; /* Host controller capabilities register */ 56 uint wml; /* Watermark level register */ 57 uint mixctrl; /* For USDHC */ 58 char reserved1[4]; /* reserved */ 59 uint fevt; /* Force event register */ 60 uint admaes; /* ADMA error status register */ 61 uint adsaddr; /* ADMA system address register */ 62 char reserved2[4]; 63 uint dllctrl; 64 uint dllstat; 65 uint clktunectrlstatus; 66 char reserved3[4]; 67 uint strobe_dllctrl; 68 uint strobe_dllstat; 69 char reserved4[72]; 70 uint vendorspec; 71 uint mmcboot; 72 uint vendorspec2; 73 uint tuning_ctrl; /* on i.MX6/7/8 */ 74 char reserved5[44]; 75 uint hostver; /* Host controller version register */ 76 char reserved6[4]; /* reserved */ 77 uint dmaerraddr; /* DMA error address register */ 78 char reserved7[4]; /* reserved */ 79 uint dmaerrattr; /* DMA error attribute register */ 80 char reserved8[4]; /* reserved */ 81 uint hostcapblt2; /* Host controller capabilities register 2 */ 82 char reserved9[8]; /* reserved */ 83 uint tcr; /* Tuning control register */ 84 char reserved10[28]; /* reserved */ 85 uint sddirctl; /* SD direction control register */ 86 char reserved11[712];/* reserved */ 87 uint scr; /* eSDHC control register */ 88 }; 89 90 struct fsl_esdhc_plat { 91 struct mmc_config cfg; 92 struct mmc mmc; 93 }; 94 95 struct esdhc_soc_data { 96 u32 flags; 97 u32 caps; 98 }; 99 100 /** 101 * struct fsl_esdhc_priv 102 * 103 * @esdhc_regs: registers of the sdhc controller 104 * @sdhc_clk: Current clk of the sdhc controller 105 * @bus_width: bus width, 1bit, 4bit or 8bit 106 * @cfg: mmc config 107 * @mmc: mmc 108 * Following is used when Driver Model is enabled for MMC 109 * @dev: pointer for the device 110 * @non_removable: 0: removable; 1: non-removable 111 * @wp_enable: 1: enable checking wp; 0: no check 112 * @vs18_enable: 1: use 1.8V voltage; 0: use 3.3V 113 * @flags: ESDHC_FLAG_xx in include/fsl_esdhc.h 114 * @caps: controller capabilities 115 * @tuning_step: tuning step setting in tuning_ctrl register 116 * @start_tuning_tap: the start point for tuning in tuning_ctrl register 117 * @strobe_dll_delay_target: settings in strobe_dllctrl 118 * @signal_voltage: indicating the current voltage 119 * @cd_gpio: gpio for card detection 120 * @wp_gpio: gpio for write protection 121 */ 122 struct fsl_esdhc_priv { 123 struct fsl_esdhc *esdhc_regs; 124 unsigned int sdhc_clk; 125 struct clk per_clk; 126 unsigned int clock; 127 unsigned int mode; 128 unsigned int bus_width; 129 #if !CONFIG_IS_ENABLED(BLK) 130 struct mmc *mmc; 131 #endif 132 struct udevice *dev; 133 int non_removable; 134 int wp_enable; 135 int vs18_enable; 136 u32 flags; 137 u32 caps; 138 u32 tuning_step; 139 u32 tuning_start_tap; 140 u32 strobe_dll_delay_target; 141 u32 signal_voltage; 142 #if IS_ENABLED(CONFIG_DM_REGULATOR) 143 struct udevice *vqmmc_dev; 144 struct udevice *vmmc_dev; 145 #endif 146 #ifdef CONFIG_DM_GPIO 147 struct gpio_desc cd_gpio; 148 struct gpio_desc wp_gpio; 149 #endif 150 }; 151 152 /* Return the XFERTYP flags for a given command and data packet */ 153 static uint esdhc_xfertyp(struct mmc_cmd *cmd, struct mmc_data *data) 154 { 155 uint xfertyp = 0; 156 157 if (data) { 158 xfertyp |= XFERTYP_DPSEL; 159 #ifndef CONFIG_SYS_FSL_ESDHC_USE_PIO 160 xfertyp |= XFERTYP_DMAEN; 161 #endif 162 if (data->blocks > 1) { 163 xfertyp |= XFERTYP_MSBSEL; 164 xfertyp |= XFERTYP_BCEN; 165 #ifdef CONFIG_SYS_FSL_ERRATUM_ESDHC111 166 xfertyp |= XFERTYP_AC12EN; 167 #endif 168 } 169 170 if (data->flags & MMC_DATA_READ) 171 xfertyp |= XFERTYP_DTDSEL; 172 } 173 174 if (cmd->resp_type & MMC_RSP_CRC) 175 xfertyp |= XFERTYP_CCCEN; 176 if (cmd->resp_type & MMC_RSP_OPCODE) 177 xfertyp |= XFERTYP_CICEN; 178 if (cmd->resp_type & MMC_RSP_136) 179 xfertyp |= XFERTYP_RSPTYP_136; 180 else if (cmd->resp_type & MMC_RSP_BUSY) 181 xfertyp |= XFERTYP_RSPTYP_48_BUSY; 182 else if (cmd->resp_type & MMC_RSP_PRESENT) 183 xfertyp |= XFERTYP_RSPTYP_48; 184 185 if (cmd->cmdidx == MMC_CMD_STOP_TRANSMISSION) 186 xfertyp |= XFERTYP_CMDTYP_ABORT; 187 188 return XFERTYP_CMD(cmd->cmdidx) | xfertyp; 189 } 190 191 #ifdef CONFIG_SYS_FSL_ESDHC_USE_PIO 192 /* 193 * PIO Read/Write Mode reduce the performace as DMA is not used in this mode. 194 */ 195 static void esdhc_pio_read_write(struct fsl_esdhc_priv *priv, 196 struct mmc_data *data) 197 { 198 struct fsl_esdhc *regs = priv->esdhc_regs; 199 uint blocks; 200 char *buffer; 201 uint databuf; 202 uint size; 203 uint irqstat; 204 ulong start; 205 206 if (data->flags & MMC_DATA_READ) { 207 blocks = data->blocks; 208 buffer = data->dest; 209 while (blocks) { 210 start = get_timer(0); 211 size = data->blocksize; 212 irqstat = esdhc_read32(®s->irqstat); 213 while (!(esdhc_read32(®s->prsstat) & PRSSTAT_BREN)) { 214 if (get_timer(start) > PIO_TIMEOUT) { 215 printf("\nData Read Failed in PIO Mode."); 216 return; 217 } 218 } 219 while (size && (!(irqstat & IRQSTAT_TC))) { 220 udelay(100); /* Wait before last byte transfer complete */ 221 irqstat = esdhc_read32(®s->irqstat); 222 databuf = in_le32(®s->datport); 223 *((uint *)buffer) = databuf; 224 buffer += 4; 225 size -= 4; 226 } 227 blocks--; 228 } 229 } else { 230 blocks = data->blocks; 231 buffer = (char *)data->src; 232 while (blocks) { 233 start = get_timer(0); 234 size = data->blocksize; 235 irqstat = esdhc_read32(®s->irqstat); 236 while (!(esdhc_read32(®s->prsstat) & PRSSTAT_BWEN)) { 237 if (get_timer(start) > PIO_TIMEOUT) { 238 printf("\nData Write Failed in PIO Mode."); 239 return; 240 } 241 } 242 while (size && (!(irqstat & IRQSTAT_TC))) { 243 udelay(100); /* Wait before last byte transfer complete */ 244 databuf = *((uint *)buffer); 245 buffer += 4; 246 size -= 4; 247 irqstat = esdhc_read32(®s->irqstat); 248 out_le32(®s->datport, databuf); 249 } 250 blocks--; 251 } 252 } 253 } 254 #endif 255 256 static int esdhc_setup_data(struct fsl_esdhc_priv *priv, struct mmc *mmc, 257 struct mmc_data *data) 258 { 259 int timeout; 260 struct fsl_esdhc *regs = priv->esdhc_regs; 261 #if defined(CONFIG_FSL_LAYERSCAPE) || defined(CONFIG_S32V234) || \ 262 defined(CONFIG_IMX8) || defined(CONFIG_IMX8M) 263 dma_addr_t addr; 264 #endif 265 uint wml_value; 266 267 wml_value = data->blocksize/4; 268 269 if (data->flags & MMC_DATA_READ) { 270 if (wml_value > WML_RD_WML_MAX) 271 wml_value = WML_RD_WML_MAX_VAL; 272 273 esdhc_clrsetbits32(®s->wml, WML_RD_WML_MASK, wml_value); 274 #ifndef CONFIG_SYS_FSL_ESDHC_USE_PIO 275 #if defined(CONFIG_FSL_LAYERSCAPE) || defined(CONFIG_S32V234) || \ 276 defined(CONFIG_IMX8) || defined(CONFIG_IMX8M) 277 addr = virt_to_phys((void *)(data->dest)); 278 if (upper_32_bits(addr)) 279 printf("Error found for upper 32 bits\n"); 280 else 281 esdhc_write32(®s->dsaddr, lower_32_bits(addr)); 282 #else 283 esdhc_write32(®s->dsaddr, (u32)data->dest); 284 #endif 285 #endif 286 } else { 287 #ifndef CONFIG_SYS_FSL_ESDHC_USE_PIO 288 flush_dcache_range((ulong)data->src, 289 (ulong)data->src+data->blocks 290 *data->blocksize); 291 #endif 292 if (wml_value > WML_WR_WML_MAX) 293 wml_value = WML_WR_WML_MAX_VAL; 294 if (priv->wp_enable) { 295 if ((esdhc_read32(®s->prsstat) & 296 PRSSTAT_WPSPL) == 0) { 297 printf("\nThe SD card is locked. Can not write to a locked card.\n\n"); 298 return -ETIMEDOUT; 299 } 300 } 301 302 esdhc_clrsetbits32(®s->wml, WML_WR_WML_MASK, 303 wml_value << 16); 304 #ifndef CONFIG_SYS_FSL_ESDHC_USE_PIO 305 #if defined(CONFIG_FSL_LAYERSCAPE) || defined(CONFIG_S32V234) || \ 306 defined(CONFIG_IMX8) || defined(CONFIG_IMX8M) 307 addr = virt_to_phys((void *)(data->src)); 308 if (upper_32_bits(addr)) 309 printf("Error found for upper 32 bits\n"); 310 else 311 esdhc_write32(®s->dsaddr, lower_32_bits(addr)); 312 #else 313 esdhc_write32(®s->dsaddr, (u32)data->src); 314 #endif 315 #endif 316 } 317 318 esdhc_write32(®s->blkattr, data->blocks << 16 | data->blocksize); 319 320 /* Calculate the timeout period for data transactions */ 321 /* 322 * 1)Timeout period = (2^(timeout+13)) SD Clock cycles 323 * 2)Timeout period should be minimum 0.250sec as per SD Card spec 324 * So, Number of SD Clock cycles for 0.25sec should be minimum 325 * (SD Clock/sec * 0.25 sec) SD Clock cycles 326 * = (mmc->clock * 1/4) SD Clock cycles 327 * As 1) >= 2) 328 * => (2^(timeout+13)) >= mmc->clock * 1/4 329 * Taking log2 both the sides 330 * => timeout + 13 >= log2(mmc->clock/4) 331 * Rounding up to next power of 2 332 * => timeout + 13 = log2(mmc->clock/4) + 1 333 * => timeout + 13 = fls(mmc->clock/4) 334 * 335 * However, the MMC spec "It is strongly recommended for hosts to 336 * implement more than 500ms timeout value even if the card 337 * indicates the 250ms maximum busy length." Even the previous 338 * value of 300ms is known to be insufficient for some cards. 339 * So, we use 340 * => timeout + 13 = fls(mmc->clock/2) 341 */ 342 timeout = fls(mmc->clock/2); 343 timeout -= 13; 344 345 if (timeout > 14) 346 timeout = 14; 347 348 if (timeout < 0) 349 timeout = 0; 350 351 #ifdef CONFIG_SYS_FSL_ERRATUM_ESDHC_A001 352 if ((timeout == 4) || (timeout == 8) || (timeout == 12)) 353 timeout++; 354 #endif 355 356 #ifdef ESDHCI_QUIRK_BROKEN_TIMEOUT_VALUE 357 timeout = 0xE; 358 #endif 359 esdhc_clrsetbits32(®s->sysctl, SYSCTL_TIMEOUT_MASK, timeout << 16); 360 361 return 0; 362 } 363 364 static void check_and_invalidate_dcache_range 365 (struct mmc_cmd *cmd, 366 struct mmc_data *data) { 367 unsigned start = 0; 368 unsigned end = 0; 369 unsigned size = roundup(ARCH_DMA_MINALIGN, 370 data->blocks*data->blocksize); 371 #if defined(CONFIG_FSL_LAYERSCAPE) || defined(CONFIG_S32V234) || \ 372 defined(CONFIG_IMX8) || defined(CONFIG_IMX8M) 373 dma_addr_t addr; 374 375 addr = virt_to_phys((void *)(data->dest)); 376 if (upper_32_bits(addr)) 377 printf("Error found for upper 32 bits\n"); 378 else 379 start = lower_32_bits(addr); 380 #else 381 start = (unsigned)data->dest; 382 #endif 383 end = start + size; 384 invalidate_dcache_range(start, end); 385 } 386 387 /* 388 * Sends a command out on the bus. Takes the mmc pointer, 389 * a command pointer, and an optional data pointer. 390 */ 391 static int esdhc_send_cmd_common(struct fsl_esdhc_priv *priv, struct mmc *mmc, 392 struct mmc_cmd *cmd, struct mmc_data *data) 393 { 394 int err = 0; 395 uint xfertyp; 396 uint irqstat; 397 u32 flags = IRQSTAT_CC | IRQSTAT_CTOE; 398 struct fsl_esdhc *regs = priv->esdhc_regs; 399 unsigned long start; 400 401 #ifdef CONFIG_SYS_FSL_ERRATUM_ESDHC111 402 if (cmd->cmdidx == MMC_CMD_STOP_TRANSMISSION) 403 return 0; 404 #endif 405 406 esdhc_write32(®s->irqstat, -1); 407 408 sync(); 409 410 /* Wait for the bus to be idle */ 411 while ((esdhc_read32(®s->prsstat) & PRSSTAT_CICHB) || 412 (esdhc_read32(®s->prsstat) & PRSSTAT_CIDHB)) 413 ; 414 415 while (esdhc_read32(®s->prsstat) & PRSSTAT_DLA) 416 ; 417 418 /* Wait at least 8 SD clock cycles before the next command */ 419 /* 420 * Note: This is way more than 8 cycles, but 1ms seems to 421 * resolve timing issues with some cards 422 */ 423 udelay(1000); 424 425 /* Set up for a data transfer if we have one */ 426 if (data) { 427 err = esdhc_setup_data(priv, mmc, data); 428 if(err) 429 return err; 430 431 if (data->flags & MMC_DATA_READ) 432 check_and_invalidate_dcache_range(cmd, data); 433 } 434 435 /* Figure out the transfer arguments */ 436 xfertyp = esdhc_xfertyp(cmd, data); 437 438 /* Mask all irqs */ 439 esdhc_write32(®s->irqsigen, 0); 440 441 /* Send the command */ 442 esdhc_write32(®s->cmdarg, cmd->cmdarg); 443 #if defined(CONFIG_FSL_USDHC) 444 esdhc_write32(®s->mixctrl, 445 (esdhc_read32(®s->mixctrl) & 0xFFFFFF80) | (xfertyp & 0x7F) 446 | (mmc->ddr_mode ? XFERTYP_DDREN : 0)); 447 esdhc_write32(®s->xfertyp, xfertyp & 0xFFFF0000); 448 #else 449 esdhc_write32(®s->xfertyp, xfertyp); 450 #endif 451 452 if ((cmd->cmdidx == MMC_CMD_SEND_TUNING_BLOCK) || 453 (cmd->cmdidx == MMC_CMD_SEND_TUNING_BLOCK_HS200)) 454 flags = IRQSTAT_BRR; 455 456 /* Wait for the command to complete */ 457 start = get_timer(0); 458 while (!(esdhc_read32(®s->irqstat) & flags)) { 459 if (get_timer(start) > 1000) { 460 err = -ETIMEDOUT; 461 goto out; 462 } 463 } 464 465 irqstat = esdhc_read32(®s->irqstat); 466 467 if (irqstat & CMD_ERR) { 468 err = -ECOMM; 469 goto out; 470 } 471 472 if (irqstat & IRQSTAT_CTOE) { 473 err = -ETIMEDOUT; 474 goto out; 475 } 476 477 /* Switch voltage to 1.8V if CMD11 succeeded */ 478 if (cmd->cmdidx == SD_CMD_SWITCH_UHS18V) { 479 esdhc_setbits32(®s->vendorspec, ESDHC_VENDORSPEC_VSELECT); 480 481 printf("Run CMD11 1.8V switch\n"); 482 /* Sleep for 5 ms - max time for card to switch to 1.8V */ 483 udelay(5000); 484 } 485 486 /* Workaround for ESDHC errata ENGcm03648 */ 487 if (!data && (cmd->resp_type & MMC_RSP_BUSY)) { 488 int timeout = 6000; 489 490 /* Poll on DATA0 line for cmd with busy signal for 600 ms */ 491 while (timeout > 0 && !(esdhc_read32(®s->prsstat) & 492 PRSSTAT_DAT0)) { 493 udelay(100); 494 timeout--; 495 } 496 497 if (timeout <= 0) { 498 printf("Timeout waiting for DAT0 to go high!\n"); 499 err = -ETIMEDOUT; 500 goto out; 501 } 502 } 503 504 /* Copy the response to the response buffer */ 505 if (cmd->resp_type & MMC_RSP_136) { 506 u32 cmdrsp3, cmdrsp2, cmdrsp1, cmdrsp0; 507 508 cmdrsp3 = esdhc_read32(®s->cmdrsp3); 509 cmdrsp2 = esdhc_read32(®s->cmdrsp2); 510 cmdrsp1 = esdhc_read32(®s->cmdrsp1); 511 cmdrsp0 = esdhc_read32(®s->cmdrsp0); 512 cmd->response[0] = (cmdrsp3 << 8) | (cmdrsp2 >> 24); 513 cmd->response[1] = (cmdrsp2 << 8) | (cmdrsp1 >> 24); 514 cmd->response[2] = (cmdrsp1 << 8) | (cmdrsp0 >> 24); 515 cmd->response[3] = (cmdrsp0 << 8); 516 } else 517 cmd->response[0] = esdhc_read32(®s->cmdrsp0); 518 519 /* Wait until all of the blocks are transferred */ 520 if (data) { 521 #ifdef CONFIG_SYS_FSL_ESDHC_USE_PIO 522 esdhc_pio_read_write(priv, data); 523 #else 524 flags = DATA_COMPLETE; 525 if ((cmd->cmdidx == MMC_CMD_SEND_TUNING_BLOCK) || 526 (cmd->cmdidx == MMC_CMD_SEND_TUNING_BLOCK_HS200)) { 527 flags = IRQSTAT_BRR; 528 } 529 530 do { 531 irqstat = esdhc_read32(®s->irqstat); 532 533 if (irqstat & IRQSTAT_DTOE) { 534 err = -ETIMEDOUT; 535 goto out; 536 } 537 538 if (irqstat & DATA_ERR) { 539 err = -ECOMM; 540 goto out; 541 } 542 } while ((irqstat & flags) != flags); 543 544 /* 545 * Need invalidate the dcache here again to avoid any 546 * cache-fill during the DMA operations such as the 547 * speculative pre-fetching etc. 548 */ 549 if (data->flags & MMC_DATA_READ) 550 check_and_invalidate_dcache_range(cmd, data); 551 #endif 552 } 553 554 out: 555 /* Reset CMD and DATA portions on error */ 556 if (err) { 557 esdhc_write32(®s->sysctl, esdhc_read32(®s->sysctl) | 558 SYSCTL_RSTC); 559 while (esdhc_read32(®s->sysctl) & SYSCTL_RSTC) 560 ; 561 562 if (data) { 563 esdhc_write32(®s->sysctl, 564 esdhc_read32(®s->sysctl) | 565 SYSCTL_RSTD); 566 while ((esdhc_read32(®s->sysctl) & SYSCTL_RSTD)) 567 ; 568 } 569 570 /* If this was CMD11, then notify that power cycle is needed */ 571 if (cmd->cmdidx == SD_CMD_SWITCH_UHS18V) 572 printf("CMD11 to switch to 1.8V mode failed, card requires power cycle.\n"); 573 } 574 575 esdhc_write32(®s->irqstat, -1); 576 577 return err; 578 } 579 580 static void set_sysctl(struct fsl_esdhc_priv *priv, struct mmc *mmc, uint clock) 581 { 582 struct fsl_esdhc *regs = priv->esdhc_regs; 583 int div = 1; 584 #ifdef ARCH_MXC 585 #ifdef CONFIG_MX53 586 /* For i.MX53 eSDHCv3, SYSCTL.SDCLKFS may not be set to 0. */ 587 int pre_div = (regs == (struct fsl_esdhc *)MMC_SDHC3_BASE_ADDR) ? 2 : 1; 588 #else 589 int pre_div = 1; 590 #endif 591 #else 592 int pre_div = 2; 593 #endif 594 int ddr_pre_div = mmc->ddr_mode ? 2 : 1; 595 int sdhc_clk = priv->sdhc_clk; 596 uint clk; 597 598 if (clock < mmc->cfg->f_min) 599 clock = mmc->cfg->f_min; 600 601 while (sdhc_clk / (16 * pre_div * ddr_pre_div) > clock && pre_div < 256) 602 pre_div *= 2; 603 604 while (sdhc_clk / (div * pre_div * ddr_pre_div) > clock && div < 16) 605 div++; 606 607 pre_div >>= 1; 608 div -= 1; 609 610 clk = (pre_div << 8) | (div << 4); 611 612 #ifdef CONFIG_FSL_USDHC 613 esdhc_clrbits32(®s->vendorspec, VENDORSPEC_CKEN); 614 #else 615 esdhc_clrbits32(®s->sysctl, SYSCTL_CKEN); 616 #endif 617 618 esdhc_clrsetbits32(®s->sysctl, SYSCTL_CLOCK_MASK, clk); 619 620 udelay(10000); 621 622 #ifdef CONFIG_FSL_USDHC 623 esdhc_setbits32(®s->vendorspec, VENDORSPEC_PEREN | VENDORSPEC_CKEN); 624 #else 625 esdhc_setbits32(®s->sysctl, SYSCTL_PEREN | SYSCTL_CKEN); 626 #endif 627 628 priv->clock = clock; 629 } 630 631 #ifdef CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK 632 static void esdhc_clock_control(struct fsl_esdhc_priv *priv, bool enable) 633 { 634 struct fsl_esdhc *regs = priv->esdhc_regs; 635 u32 value; 636 u32 time_out; 637 638 value = esdhc_read32(®s->sysctl); 639 640 if (enable) 641 value |= SYSCTL_CKEN; 642 else 643 value &= ~SYSCTL_CKEN; 644 645 esdhc_write32(®s->sysctl, value); 646 647 time_out = 20; 648 value = PRSSTAT_SDSTB; 649 while (!(esdhc_read32(®s->prsstat) & value)) { 650 if (time_out == 0) { 651 printf("fsl_esdhc: Internal clock never stabilised.\n"); 652 break; 653 } 654 time_out--; 655 mdelay(1); 656 } 657 } 658 #endif 659 660 #ifdef MMC_SUPPORTS_TUNING 661 static int esdhc_change_pinstate(struct udevice *dev) 662 { 663 struct fsl_esdhc_priv *priv = dev_get_priv(dev); 664 int ret; 665 666 switch (priv->mode) { 667 case UHS_SDR50: 668 case UHS_DDR50: 669 ret = pinctrl_select_state(dev, "state_100mhz"); 670 break; 671 case UHS_SDR104: 672 case MMC_HS_200: 673 case MMC_HS_400: 674 ret = pinctrl_select_state(dev, "state_200mhz"); 675 break; 676 default: 677 ret = pinctrl_select_state(dev, "default"); 678 break; 679 } 680 681 if (ret) 682 printf("%s %d error\n", __func__, priv->mode); 683 684 return ret; 685 } 686 687 static void esdhc_reset_tuning(struct mmc *mmc) 688 { 689 struct fsl_esdhc_priv *priv = dev_get_priv(mmc->dev); 690 struct fsl_esdhc *regs = priv->esdhc_regs; 691 692 if (priv->flags & ESDHC_FLAG_USDHC) { 693 if (priv->flags & ESDHC_FLAG_STD_TUNING) { 694 esdhc_clrbits32(®s->autoc12err, 695 MIX_CTRL_SMPCLK_SEL | 696 MIX_CTRL_EXE_TUNE); 697 } 698 } 699 } 700 701 static void esdhc_set_strobe_dll(struct mmc *mmc) 702 { 703 struct fsl_esdhc_priv *priv = dev_get_priv(mmc->dev); 704 struct fsl_esdhc *regs = priv->esdhc_regs; 705 u32 val; 706 707 if (priv->clock > ESDHC_STROBE_DLL_CLK_FREQ) { 708 writel(ESDHC_STROBE_DLL_CTRL_RESET, ®s->strobe_dllctrl); 709 710 /* 711 * enable strobe dll ctrl and adjust the delay target 712 * for the uSDHC loopback read clock 713 */ 714 val = ESDHC_STROBE_DLL_CTRL_ENABLE | 715 (priv->strobe_dll_delay_target << 716 ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_SHIFT); 717 writel(val, ®s->strobe_dllctrl); 718 /* wait 1us to make sure strobe dll status register stable */ 719 mdelay(1); 720 val = readl(®s->strobe_dllstat); 721 if (!(val & ESDHC_STROBE_DLL_STS_REF_LOCK)) 722 pr_warn("HS400 strobe DLL status REF not lock!\n"); 723 if (!(val & ESDHC_STROBE_DLL_STS_SLV_LOCK)) 724 pr_warn("HS400 strobe DLL status SLV not lock!\n"); 725 } 726 } 727 728 static int esdhc_set_timing(struct mmc *mmc) 729 { 730 struct fsl_esdhc_priv *priv = dev_get_priv(mmc->dev); 731 struct fsl_esdhc *regs = priv->esdhc_regs; 732 u32 mixctrl; 733 734 mixctrl = readl(®s->mixctrl); 735 mixctrl &= ~(MIX_CTRL_DDREN | MIX_CTRL_HS400_EN); 736 737 switch (mmc->selected_mode) { 738 case MMC_LEGACY: 739 case SD_LEGACY: 740 esdhc_reset_tuning(mmc); 741 writel(mixctrl, ®s->mixctrl); 742 break; 743 case MMC_HS_400: 744 mixctrl |= MIX_CTRL_DDREN | MIX_CTRL_HS400_EN; 745 writel(mixctrl, ®s->mixctrl); 746 esdhc_set_strobe_dll(mmc); 747 break; 748 case MMC_HS: 749 case MMC_HS_52: 750 case MMC_HS_200: 751 case SD_HS: 752 case UHS_SDR12: 753 case UHS_SDR25: 754 case UHS_SDR50: 755 case UHS_SDR104: 756 writel(mixctrl, ®s->mixctrl); 757 break; 758 case UHS_DDR50: 759 case MMC_DDR_52: 760 mixctrl |= MIX_CTRL_DDREN; 761 writel(mixctrl, ®s->mixctrl); 762 break; 763 default: 764 printf("Not supported %d\n", mmc->selected_mode); 765 return -EINVAL; 766 } 767 768 priv->mode = mmc->selected_mode; 769 770 return esdhc_change_pinstate(mmc->dev); 771 } 772 773 static int esdhc_set_voltage(struct mmc *mmc) 774 { 775 struct fsl_esdhc_priv *priv = dev_get_priv(mmc->dev); 776 struct fsl_esdhc *regs = priv->esdhc_regs; 777 int ret; 778 779 priv->signal_voltage = mmc->signal_voltage; 780 switch (mmc->signal_voltage) { 781 case MMC_SIGNAL_VOLTAGE_330: 782 if (priv->vs18_enable) 783 return -EIO; 784 #ifdef CONFIG_DM_REGULATOR 785 if (!IS_ERR_OR_NULL(priv->vqmmc_dev)) { 786 ret = regulator_set_value(priv->vqmmc_dev, 3300000); 787 if (ret) { 788 printf("Setting to 3.3V error"); 789 return -EIO; 790 } 791 /* Wait for 5ms */ 792 mdelay(5); 793 } 794 #endif 795 796 esdhc_clrbits32(®s->vendorspec, ESDHC_VENDORSPEC_VSELECT); 797 if (!(esdhc_read32(®s->vendorspec) & 798 ESDHC_VENDORSPEC_VSELECT)) 799 return 0; 800 801 return -EAGAIN; 802 case MMC_SIGNAL_VOLTAGE_180: 803 #ifdef CONFIG_DM_REGULATOR 804 if (!IS_ERR_OR_NULL(priv->vqmmc_dev)) { 805 ret = regulator_set_value(priv->vqmmc_dev, 1800000); 806 if (ret) { 807 printf("Setting to 1.8V error"); 808 return -EIO; 809 } 810 } 811 #endif 812 esdhc_setbits32(®s->vendorspec, ESDHC_VENDORSPEC_VSELECT); 813 if (esdhc_read32(®s->vendorspec) & ESDHC_VENDORSPEC_VSELECT) 814 return 0; 815 816 return -EAGAIN; 817 case MMC_SIGNAL_VOLTAGE_120: 818 return -ENOTSUPP; 819 default: 820 return 0; 821 } 822 } 823 824 static void esdhc_stop_tuning(struct mmc *mmc) 825 { 826 struct mmc_cmd cmd; 827 828 cmd.cmdidx = MMC_CMD_STOP_TRANSMISSION; 829 cmd.cmdarg = 0; 830 cmd.resp_type = MMC_RSP_R1b; 831 832 dm_mmc_send_cmd(mmc->dev, &cmd, NULL); 833 } 834 835 static int fsl_esdhc_execute_tuning(struct udevice *dev, uint32_t opcode) 836 { 837 struct fsl_esdhc_plat *plat = dev_get_platdata(dev); 838 struct fsl_esdhc_priv *priv = dev_get_priv(dev); 839 struct fsl_esdhc *regs = priv->esdhc_regs; 840 struct mmc *mmc = &plat->mmc; 841 u32 irqstaten = readl(®s->irqstaten); 842 u32 irqsigen = readl(®s->irqsigen); 843 int i, ret = -ETIMEDOUT; 844 u32 val, mixctrl; 845 846 /* clock tuning is not needed for upto 52MHz */ 847 if (mmc->clock <= 52000000) 848 return 0; 849 850 /* This is readw/writew SDHCI_HOST_CONTROL2 when tuning */ 851 if (priv->flags & ESDHC_FLAG_STD_TUNING) { 852 val = readl(®s->autoc12err); 853 mixctrl = readl(®s->mixctrl); 854 val &= ~MIX_CTRL_SMPCLK_SEL; 855 mixctrl &= ~(MIX_CTRL_FBCLK_SEL | MIX_CTRL_AUTO_TUNE_EN); 856 857 val |= MIX_CTRL_EXE_TUNE; 858 mixctrl |= MIX_CTRL_FBCLK_SEL | MIX_CTRL_AUTO_TUNE_EN; 859 860 writel(val, ®s->autoc12err); 861 writel(mixctrl, ®s->mixctrl); 862 } 863 864 /* sdhci_writew(host, SDHCI_TRNS_READ, SDHCI_TRANSFER_MODE); */ 865 mixctrl = readl(®s->mixctrl); 866 mixctrl = MIX_CTRL_DTDSEL_READ | (mixctrl & ~MIX_CTRL_SDHCI_MASK); 867 writel(mixctrl, ®s->mixctrl); 868 869 writel(IRQSTATEN_BRR, ®s->irqstaten); 870 writel(IRQSTATEN_BRR, ®s->irqsigen); 871 872 /* 873 * Issue opcode repeatedly till Execute Tuning is set to 0 or the number 874 * of loops reaches 40 times. 875 */ 876 for (i = 0; i < MAX_TUNING_LOOP; i++) { 877 u32 ctrl; 878 879 if (opcode == MMC_CMD_SEND_TUNING_BLOCK_HS200) { 880 if (mmc->bus_width == 8) 881 writel(0x7080, ®s->blkattr); 882 else if (mmc->bus_width == 4) 883 writel(0x7040, ®s->blkattr); 884 } else { 885 writel(0x7040, ®s->blkattr); 886 } 887 888 /* sdhci_writew(host, SDHCI_TRNS_READ, SDHCI_TRANSFER_MODE) */ 889 val = readl(®s->mixctrl); 890 val = MIX_CTRL_DTDSEL_READ | (val & ~MIX_CTRL_SDHCI_MASK); 891 writel(val, ®s->mixctrl); 892 893 /* We are using STD tuning, no need to check return value */ 894 mmc_send_tuning(mmc, opcode, NULL); 895 896 ctrl = readl(®s->autoc12err); 897 if ((!(ctrl & MIX_CTRL_EXE_TUNE)) && 898 (ctrl & MIX_CTRL_SMPCLK_SEL)) { 899 /* 900 * need to wait some time, make sure sd/mmc fininsh 901 * send out tuning data, otherwise, the sd/mmc can't 902 * response to any command when the card still out 903 * put the tuning data. 904 */ 905 mdelay(1); 906 ret = 0; 907 break; 908 } 909 910 /* Add 1ms delay for SD and eMMC */ 911 mdelay(1); 912 } 913 914 writel(irqstaten, ®s->irqstaten); 915 writel(irqsigen, ®s->irqsigen); 916 917 esdhc_stop_tuning(mmc); 918 919 return ret; 920 } 921 #endif 922 923 static int esdhc_set_ios_common(struct fsl_esdhc_priv *priv, struct mmc *mmc) 924 { 925 struct fsl_esdhc *regs = priv->esdhc_regs; 926 int ret __maybe_unused; 927 928 #ifdef CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK 929 /* Select to use peripheral clock */ 930 esdhc_clock_control(priv, false); 931 esdhc_setbits32(®s->scr, ESDHCCTL_PCS); 932 esdhc_clock_control(priv, true); 933 #endif 934 /* Set the clock speed */ 935 if (priv->clock != mmc->clock) 936 set_sysctl(priv, mmc, mmc->clock); 937 938 #ifdef MMC_SUPPORTS_TUNING 939 if (mmc->clk_disable) { 940 #ifdef CONFIG_FSL_USDHC 941 esdhc_clrbits32(®s->vendorspec, VENDORSPEC_CKEN); 942 #else 943 esdhc_clrbits32(®s->sysctl, SYSCTL_CKEN); 944 #endif 945 } else { 946 #ifdef CONFIG_FSL_USDHC 947 esdhc_setbits32(®s->vendorspec, VENDORSPEC_PEREN | 948 VENDORSPEC_CKEN); 949 #else 950 esdhc_setbits32(®s->sysctl, SYSCTL_PEREN | SYSCTL_CKEN); 951 #endif 952 } 953 954 if (priv->mode != mmc->selected_mode) { 955 ret = esdhc_set_timing(mmc); 956 if (ret) { 957 printf("esdhc_set_timing error %d\n", ret); 958 return ret; 959 } 960 } 961 962 if (priv->signal_voltage != mmc->signal_voltage) { 963 ret = esdhc_set_voltage(mmc); 964 if (ret) { 965 printf("esdhc_set_voltage error %d\n", ret); 966 return ret; 967 } 968 } 969 #endif 970 971 /* Set the bus width */ 972 esdhc_clrbits32(®s->proctl, PROCTL_DTW_4 | PROCTL_DTW_8); 973 974 if (mmc->bus_width == 4) 975 esdhc_setbits32(®s->proctl, PROCTL_DTW_4); 976 else if (mmc->bus_width == 8) 977 esdhc_setbits32(®s->proctl, PROCTL_DTW_8); 978 979 return 0; 980 } 981 982 static int esdhc_init_common(struct fsl_esdhc_priv *priv, struct mmc *mmc) 983 { 984 struct fsl_esdhc *regs = priv->esdhc_regs; 985 ulong start; 986 987 /* Reset the entire host controller */ 988 esdhc_setbits32(®s->sysctl, SYSCTL_RSTA); 989 990 /* Wait until the controller is available */ 991 start = get_timer(0); 992 while ((esdhc_read32(®s->sysctl) & SYSCTL_RSTA)) { 993 if (get_timer(start) > 1000) 994 return -ETIMEDOUT; 995 } 996 997 #if defined(CONFIG_FSL_USDHC) 998 /* RSTA doesn't reset MMC_BOOT register, so manually reset it */ 999 esdhc_write32(®s->mmcboot, 0x0); 1000 /* Reset MIX_CTRL and CLK_TUNE_CTRL_STATUS regs to 0 */ 1001 esdhc_write32(®s->mixctrl, 0x0); 1002 esdhc_write32(®s->clktunectrlstatus, 0x0); 1003 1004 /* Put VEND_SPEC to default value */ 1005 if (priv->vs18_enable) 1006 esdhc_write32(®s->vendorspec, (VENDORSPEC_INIT | 1007 ESDHC_VENDORSPEC_VSELECT)); 1008 else 1009 esdhc_write32(®s->vendorspec, VENDORSPEC_INIT); 1010 1011 /* Disable DLL_CTRL delay line */ 1012 esdhc_write32(®s->dllctrl, 0x0); 1013 #endif 1014 1015 #ifndef ARCH_MXC 1016 /* Enable cache snooping */ 1017 esdhc_write32(®s->scr, 0x00000040); 1018 #endif 1019 1020 #ifndef CONFIG_FSL_USDHC 1021 esdhc_setbits32(®s->sysctl, SYSCTL_HCKEN | SYSCTL_IPGEN); 1022 #else 1023 esdhc_setbits32(®s->vendorspec, VENDORSPEC_HCKEN | VENDORSPEC_IPGEN); 1024 #endif 1025 1026 /* Set the initial clock speed */ 1027 mmc_set_clock(mmc, 400000, MMC_CLK_ENABLE); 1028 1029 /* Disable the BRR and BWR bits in IRQSTAT */ 1030 esdhc_clrbits32(®s->irqstaten, IRQSTATEN_BRR | IRQSTATEN_BWR); 1031 1032 /* Put the PROCTL reg back to the default */ 1033 esdhc_write32(®s->proctl, PROCTL_INIT); 1034 1035 /* Set timout to the maximum value */ 1036 esdhc_clrsetbits32(®s->sysctl, SYSCTL_TIMEOUT_MASK, 14 << 16); 1037 1038 return 0; 1039 } 1040 1041 static int esdhc_getcd_common(struct fsl_esdhc_priv *priv) 1042 { 1043 struct fsl_esdhc *regs = priv->esdhc_regs; 1044 int timeout = 1000; 1045 1046 #ifdef CONFIG_ESDHC_DETECT_QUIRK 1047 if (CONFIG_ESDHC_DETECT_QUIRK) 1048 return 1; 1049 #endif 1050 1051 #if CONFIG_IS_ENABLED(DM_MMC) 1052 if (priv->non_removable) 1053 return 1; 1054 #ifdef CONFIG_DM_GPIO 1055 if (dm_gpio_is_valid(&priv->cd_gpio)) 1056 return dm_gpio_get_value(&priv->cd_gpio); 1057 #endif 1058 #endif 1059 1060 while (!(esdhc_read32(®s->prsstat) & PRSSTAT_CINS) && --timeout) 1061 udelay(1000); 1062 1063 return timeout > 0; 1064 } 1065 1066 static int esdhc_reset(struct fsl_esdhc *regs) 1067 { 1068 ulong start; 1069 1070 /* reset the controller */ 1071 esdhc_setbits32(®s->sysctl, SYSCTL_RSTA); 1072 1073 /* hardware clears the bit when it is done */ 1074 start = get_timer(0); 1075 while ((esdhc_read32(®s->sysctl) & SYSCTL_RSTA)) { 1076 if (get_timer(start) > 100) { 1077 printf("MMC/SD: Reset never completed.\n"); 1078 return -ETIMEDOUT; 1079 } 1080 } 1081 1082 return 0; 1083 } 1084 1085 #if !CONFIG_IS_ENABLED(DM_MMC) 1086 static int esdhc_getcd(struct mmc *mmc) 1087 { 1088 struct fsl_esdhc_priv *priv = mmc->priv; 1089 1090 return esdhc_getcd_common(priv); 1091 } 1092 1093 static int esdhc_init(struct mmc *mmc) 1094 { 1095 struct fsl_esdhc_priv *priv = mmc->priv; 1096 1097 return esdhc_init_common(priv, mmc); 1098 } 1099 1100 static int esdhc_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd, 1101 struct mmc_data *data) 1102 { 1103 struct fsl_esdhc_priv *priv = mmc->priv; 1104 1105 return esdhc_send_cmd_common(priv, mmc, cmd, data); 1106 } 1107 1108 static int esdhc_set_ios(struct mmc *mmc) 1109 { 1110 struct fsl_esdhc_priv *priv = mmc->priv; 1111 1112 return esdhc_set_ios_common(priv, mmc); 1113 } 1114 1115 static const struct mmc_ops esdhc_ops = { 1116 .getcd = esdhc_getcd, 1117 .init = esdhc_init, 1118 .send_cmd = esdhc_send_cmd, 1119 .set_ios = esdhc_set_ios, 1120 }; 1121 #endif 1122 1123 static int fsl_esdhc_init(struct fsl_esdhc_priv *priv, 1124 struct fsl_esdhc_plat *plat) 1125 { 1126 struct mmc_config *cfg; 1127 struct fsl_esdhc *regs; 1128 u32 caps, voltage_caps; 1129 int ret; 1130 1131 if (!priv) 1132 return -EINVAL; 1133 1134 regs = priv->esdhc_regs; 1135 1136 /* First reset the eSDHC controller */ 1137 ret = esdhc_reset(regs); 1138 if (ret) 1139 return ret; 1140 1141 #ifndef CONFIG_FSL_USDHC 1142 esdhc_setbits32(®s->sysctl, SYSCTL_PEREN | SYSCTL_HCKEN 1143 | SYSCTL_IPGEN | SYSCTL_CKEN); 1144 /* Clearing tuning bits in case ROM has set it already */ 1145 esdhc_write32(®s->mixctrl, 0); 1146 esdhc_write32(®s->autoc12err, 0); 1147 esdhc_write32(®s->clktunectrlstatus, 0); 1148 #else 1149 esdhc_setbits32(®s->vendorspec, VENDORSPEC_PEREN | 1150 VENDORSPEC_HCKEN | VENDORSPEC_IPGEN | VENDORSPEC_CKEN); 1151 #endif 1152 1153 if (priv->vs18_enable) 1154 esdhc_setbits32(®s->vendorspec, ESDHC_VENDORSPEC_VSELECT); 1155 1156 writel(SDHCI_IRQ_EN_BITS, ®s->irqstaten); 1157 cfg = &plat->cfg; 1158 #ifndef CONFIG_DM_MMC 1159 memset(cfg, '\0', sizeof(*cfg)); 1160 #endif 1161 1162 voltage_caps = 0; 1163 caps = esdhc_read32(®s->hostcapblt); 1164 1165 #ifdef CONFIG_SYS_FSL_ERRATUM_ESDHC135 1166 caps = caps & ~(ESDHC_HOSTCAPBLT_SRS | 1167 ESDHC_HOSTCAPBLT_VS18 | ESDHC_HOSTCAPBLT_VS30); 1168 #endif 1169 1170 /* T4240 host controller capabilities register should have VS33 bit */ 1171 #ifdef CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 1172 caps = caps | ESDHC_HOSTCAPBLT_VS33; 1173 #endif 1174 1175 if (caps & ESDHC_HOSTCAPBLT_VS18) 1176 voltage_caps |= MMC_VDD_165_195; 1177 if (caps & ESDHC_HOSTCAPBLT_VS30) 1178 voltage_caps |= MMC_VDD_29_30 | MMC_VDD_30_31; 1179 if (caps & ESDHC_HOSTCAPBLT_VS33) 1180 voltage_caps |= MMC_VDD_32_33 | MMC_VDD_33_34; 1181 1182 cfg->name = "FSL_SDHC"; 1183 #if !CONFIG_IS_ENABLED(DM_MMC) 1184 cfg->ops = &esdhc_ops; 1185 #endif 1186 #ifdef CONFIG_SYS_SD_VOLTAGE 1187 cfg->voltages = CONFIG_SYS_SD_VOLTAGE; 1188 #else 1189 cfg->voltages = MMC_VDD_32_33 | MMC_VDD_33_34; 1190 #endif 1191 if ((cfg->voltages & voltage_caps) == 0) { 1192 printf("voltage not supported by controller\n"); 1193 return -1; 1194 } 1195 1196 if (priv->bus_width == 8) 1197 cfg->host_caps = MMC_MODE_4BIT | MMC_MODE_8BIT; 1198 else if (priv->bus_width == 4) 1199 cfg->host_caps = MMC_MODE_4BIT; 1200 1201 cfg->host_caps = MMC_MODE_4BIT | MMC_MODE_8BIT; 1202 #ifdef CONFIG_SYS_FSL_ESDHC_HAS_DDR_MODE 1203 cfg->host_caps |= MMC_MODE_DDR_52MHz; 1204 #endif 1205 1206 if (priv->bus_width > 0) { 1207 if (priv->bus_width < 8) 1208 cfg->host_caps &= ~MMC_MODE_8BIT; 1209 if (priv->bus_width < 4) 1210 cfg->host_caps &= ~MMC_MODE_4BIT; 1211 } 1212 1213 if (caps & ESDHC_HOSTCAPBLT_HSS) 1214 cfg->host_caps |= MMC_MODE_HS_52MHz | MMC_MODE_HS; 1215 1216 #ifdef CONFIG_ESDHC_DETECT_8_BIT_QUIRK 1217 if (CONFIG_ESDHC_DETECT_8_BIT_QUIRK) 1218 cfg->host_caps &= ~MMC_MODE_8BIT; 1219 #endif 1220 1221 cfg->host_caps |= priv->caps; 1222 1223 cfg->f_min = 400000; 1224 cfg->f_max = min(priv->sdhc_clk, (u32)200000000); 1225 1226 cfg->b_max = CONFIG_SYS_MMC_MAX_BLK_COUNT; 1227 1228 writel(0, ®s->dllctrl); 1229 if (priv->flags & ESDHC_FLAG_USDHC) { 1230 if (priv->flags & ESDHC_FLAG_STD_TUNING) { 1231 u32 val = readl(®s->tuning_ctrl); 1232 1233 val |= ESDHC_STD_TUNING_EN; 1234 val &= ~ESDHC_TUNING_START_TAP_MASK; 1235 val |= priv->tuning_start_tap; 1236 val &= ~ESDHC_TUNING_STEP_MASK; 1237 val |= (priv->tuning_step) << ESDHC_TUNING_STEP_SHIFT; 1238 writel(val, ®s->tuning_ctrl); 1239 } 1240 } 1241 1242 return 0; 1243 } 1244 1245 #if !CONFIG_IS_ENABLED(DM_MMC) 1246 static int fsl_esdhc_cfg_to_priv(struct fsl_esdhc_cfg *cfg, 1247 struct fsl_esdhc_priv *priv) 1248 { 1249 if (!cfg || !priv) 1250 return -EINVAL; 1251 1252 priv->esdhc_regs = (struct fsl_esdhc *)(unsigned long)(cfg->esdhc_base); 1253 priv->bus_width = cfg->max_bus_width; 1254 priv->sdhc_clk = cfg->sdhc_clk; 1255 priv->wp_enable = cfg->wp_enable; 1256 priv->vs18_enable = cfg->vs18_enable; 1257 1258 return 0; 1259 }; 1260 1261 int fsl_esdhc_initialize(bd_t *bis, struct fsl_esdhc_cfg *cfg) 1262 { 1263 struct fsl_esdhc_plat *plat; 1264 struct fsl_esdhc_priv *priv; 1265 struct mmc *mmc; 1266 int ret; 1267 1268 if (!cfg) 1269 return -EINVAL; 1270 1271 priv = calloc(sizeof(struct fsl_esdhc_priv), 1); 1272 if (!priv) 1273 return -ENOMEM; 1274 plat = calloc(sizeof(struct fsl_esdhc_plat), 1); 1275 if (!plat) { 1276 free(priv); 1277 return -ENOMEM; 1278 } 1279 1280 ret = fsl_esdhc_cfg_to_priv(cfg, priv); 1281 if (ret) { 1282 debug("%s xlate failure\n", __func__); 1283 free(plat); 1284 free(priv); 1285 return ret; 1286 } 1287 1288 ret = fsl_esdhc_init(priv, plat); 1289 if (ret) { 1290 debug("%s init failure\n", __func__); 1291 free(plat); 1292 free(priv); 1293 return ret; 1294 } 1295 1296 mmc = mmc_create(&plat->cfg, priv); 1297 if (!mmc) 1298 return -EIO; 1299 1300 priv->mmc = mmc; 1301 1302 return 0; 1303 } 1304 1305 int fsl_esdhc_mmc_init(bd_t *bis) 1306 { 1307 struct fsl_esdhc_cfg *cfg; 1308 1309 cfg = calloc(sizeof(struct fsl_esdhc_cfg), 1); 1310 cfg->esdhc_base = CONFIG_SYS_FSL_ESDHC_ADDR; 1311 cfg->sdhc_clk = gd->arch.sdhc_clk; 1312 return fsl_esdhc_initialize(bis, cfg); 1313 } 1314 #endif 1315 1316 #ifdef CONFIG_FSL_ESDHC_ADAPTER_IDENT 1317 void mmc_adapter_card_type_ident(void) 1318 { 1319 u8 card_id; 1320 u8 value; 1321 1322 card_id = QIXIS_READ(present) & QIXIS_SDID_MASK; 1323 gd->arch.sdhc_adapter = card_id; 1324 1325 switch (card_id) { 1326 case QIXIS_ESDHC_ADAPTER_TYPE_EMMC45: 1327 value = QIXIS_READ(brdcfg[5]); 1328 value |= (QIXIS_DAT4 | QIXIS_DAT5_6_7); 1329 QIXIS_WRITE(brdcfg[5], value); 1330 break; 1331 case QIXIS_ESDHC_ADAPTER_TYPE_SDMMC_LEGACY: 1332 value = QIXIS_READ(pwr_ctl[1]); 1333 value |= QIXIS_EVDD_BY_SDHC_VS; 1334 QIXIS_WRITE(pwr_ctl[1], value); 1335 break; 1336 case QIXIS_ESDHC_ADAPTER_TYPE_EMMC44: 1337 value = QIXIS_READ(brdcfg[5]); 1338 value |= (QIXIS_SDCLKIN | QIXIS_SDCLKOUT); 1339 QIXIS_WRITE(brdcfg[5], value); 1340 break; 1341 case QIXIS_ESDHC_ADAPTER_TYPE_RSV: 1342 break; 1343 case QIXIS_ESDHC_ADAPTER_TYPE_MMC: 1344 break; 1345 case QIXIS_ESDHC_ADAPTER_TYPE_SD: 1346 break; 1347 case QIXIS_ESDHC_NO_ADAPTER: 1348 break; 1349 default: 1350 break; 1351 } 1352 } 1353 #endif 1354 1355 #ifdef CONFIG_OF_LIBFDT 1356 __weak int esdhc_status_fixup(void *blob, const char *compat) 1357 { 1358 #ifdef CONFIG_FSL_ESDHC_PIN_MUX 1359 if (!hwconfig("esdhc")) { 1360 do_fixup_by_compat(blob, compat, "status", "disabled", 1361 sizeof("disabled"), 1); 1362 return 1; 1363 } 1364 #endif 1365 return 0; 1366 } 1367 1368 void fdt_fixup_esdhc(void *blob, bd_t *bd) 1369 { 1370 const char *compat = "fsl,esdhc"; 1371 1372 if (esdhc_status_fixup(blob, compat)) 1373 return; 1374 1375 #ifdef CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK 1376 do_fixup_by_compat_u32(blob, compat, "peripheral-frequency", 1377 gd->arch.sdhc_clk, 1); 1378 #else 1379 do_fixup_by_compat_u32(blob, compat, "clock-frequency", 1380 gd->arch.sdhc_clk, 1); 1381 #endif 1382 #ifdef CONFIG_FSL_ESDHC_ADAPTER_IDENT 1383 do_fixup_by_compat_u32(blob, compat, "adapter-type", 1384 (u32)(gd->arch.sdhc_adapter), 1); 1385 #endif 1386 } 1387 #endif 1388 1389 #if CONFIG_IS_ENABLED(DM_MMC) 1390 #include <asm/arch/clock.h> 1391 __weak void init_clk_usdhc(u32 index) 1392 { 1393 } 1394 1395 static int fsl_esdhc_probe(struct udevice *dev) 1396 { 1397 struct mmc_uclass_priv *upriv = dev_get_uclass_priv(dev); 1398 struct fsl_esdhc_plat *plat = dev_get_platdata(dev); 1399 struct fsl_esdhc_priv *priv = dev_get_priv(dev); 1400 const void *fdt = gd->fdt_blob; 1401 int node = dev_of_offset(dev); 1402 struct esdhc_soc_data *data = 1403 (struct esdhc_soc_data *)dev_get_driver_data(dev); 1404 #ifdef CONFIG_DM_REGULATOR 1405 struct udevice *vqmmc_dev; 1406 #endif 1407 fdt_addr_t addr; 1408 unsigned int val; 1409 struct mmc *mmc; 1410 int ret; 1411 1412 addr = dev_read_addr(dev); 1413 if (addr == FDT_ADDR_T_NONE) 1414 return -EINVAL; 1415 1416 priv->esdhc_regs = (struct fsl_esdhc *)addr; 1417 priv->dev = dev; 1418 priv->mode = -1; 1419 if (data) { 1420 priv->flags = data->flags; 1421 priv->caps = data->caps; 1422 } 1423 1424 val = dev_read_u32_default(dev, "bus-width", -1); 1425 if (val == 8) 1426 priv->bus_width = 8; 1427 else if (val == 4) 1428 priv->bus_width = 4; 1429 else 1430 priv->bus_width = 1; 1431 1432 val = fdtdec_get_int(fdt, node, "fsl,tuning-step", 1); 1433 priv->tuning_step = val; 1434 val = fdtdec_get_int(fdt, node, "fsl,tuning-start-tap", 1435 ESDHC_TUNING_START_TAP_DEFAULT); 1436 priv->tuning_start_tap = val; 1437 val = fdtdec_get_int(fdt, node, "fsl,strobe-dll-delay-target", 1438 ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_DEFAULT); 1439 priv->strobe_dll_delay_target = val; 1440 1441 if (dev_read_bool(dev, "non-removable")) { 1442 priv->non_removable = 1; 1443 } else { 1444 priv->non_removable = 0; 1445 #ifdef CONFIG_DM_GPIO 1446 gpio_request_by_name(dev, "cd-gpios", 0, &priv->cd_gpio, 1447 GPIOD_IS_IN); 1448 #endif 1449 } 1450 1451 priv->wp_enable = 1; 1452 1453 #ifdef CONFIG_DM_GPIO 1454 ret = gpio_request_by_name(dev, "wp-gpios", 0, &priv->wp_gpio, 1455 GPIOD_IS_IN); 1456 if (ret) 1457 priv->wp_enable = 0; 1458 #endif 1459 1460 priv->vs18_enable = 0; 1461 1462 #ifdef CONFIG_DM_REGULATOR 1463 /* 1464 * If emmc I/O has a fixed voltage at 1.8V, this must be provided, 1465 * otherwise, emmc will work abnormally. 1466 */ 1467 ret = device_get_supply_regulator(dev, "vqmmc-supply", &vqmmc_dev); 1468 if (ret) { 1469 dev_dbg(dev, "no vqmmc-supply\n"); 1470 } else { 1471 ret = regulator_set_enable(vqmmc_dev, true); 1472 if (ret) { 1473 dev_err(dev, "fail to enable vqmmc-supply\n"); 1474 return ret; 1475 } 1476 1477 if (regulator_get_value(vqmmc_dev) == 1800000) 1478 priv->vs18_enable = 1; 1479 } 1480 #endif 1481 1482 if (fdt_get_property(fdt, node, "no-1-8-v", NULL)) 1483 priv->caps &= ~(UHS_CAPS | MMC_MODE_HS200 | MMC_MODE_HS400); 1484 1485 /* 1486 * TODO: 1487 * Because lack of clk driver, if SDHC clk is not enabled, 1488 * need to enable it first before this driver is invoked. 1489 * 1490 * we use MXC_ESDHC_CLK to get clk freq. 1491 * If one would like to make this function work, 1492 * the aliases should be provided in dts as this: 1493 * 1494 * aliases { 1495 * mmc0 = &usdhc1; 1496 * mmc1 = &usdhc2; 1497 * mmc2 = &usdhc3; 1498 * mmc3 = &usdhc4; 1499 * }; 1500 * Then if your board only supports mmc2 and mmc3, but we can 1501 * correctly get the seq as 2 and 3, then let mxc_get_clock 1502 * work as expected. 1503 */ 1504 1505 init_clk_usdhc(dev->seq); 1506 1507 if (IS_ENABLED(CONFIG_CLK)) { 1508 /* Assigned clock already set clock */ 1509 ret = clk_get_by_name(dev, "per", &priv->per_clk); 1510 if (ret) { 1511 printf("Failed to get per_clk\n"); 1512 return ret; 1513 } 1514 ret = clk_enable(&priv->per_clk); 1515 if (ret) { 1516 printf("Failed to enable per_clk\n"); 1517 return ret; 1518 } 1519 1520 priv->sdhc_clk = clk_get_rate(&priv->per_clk); 1521 } else { 1522 priv->sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK + dev->seq); 1523 if (priv->sdhc_clk <= 0) { 1524 dev_err(dev, "Unable to get clk for %s\n", dev->name); 1525 return -EINVAL; 1526 } 1527 } 1528 1529 ret = fsl_esdhc_init(priv, plat); 1530 if (ret) { 1531 dev_err(dev, "fsl_esdhc_init failure\n"); 1532 return ret; 1533 } 1534 1535 mmc = &plat->mmc; 1536 mmc->cfg = &plat->cfg; 1537 mmc->dev = dev; 1538 upriv->mmc = mmc; 1539 1540 return esdhc_init_common(priv, mmc); 1541 } 1542 1543 #if CONFIG_IS_ENABLED(DM_MMC) 1544 static int fsl_esdhc_get_cd(struct udevice *dev) 1545 { 1546 struct fsl_esdhc_priv *priv = dev_get_priv(dev); 1547 1548 return esdhc_getcd_common(priv); 1549 } 1550 1551 static int fsl_esdhc_send_cmd(struct udevice *dev, struct mmc_cmd *cmd, 1552 struct mmc_data *data) 1553 { 1554 struct fsl_esdhc_plat *plat = dev_get_platdata(dev); 1555 struct fsl_esdhc_priv *priv = dev_get_priv(dev); 1556 1557 return esdhc_send_cmd_common(priv, &plat->mmc, cmd, data); 1558 } 1559 1560 static int fsl_esdhc_set_ios(struct udevice *dev) 1561 { 1562 struct fsl_esdhc_plat *plat = dev_get_platdata(dev); 1563 struct fsl_esdhc_priv *priv = dev_get_priv(dev); 1564 1565 return esdhc_set_ios_common(priv, &plat->mmc); 1566 } 1567 1568 static const struct dm_mmc_ops fsl_esdhc_ops = { 1569 .get_cd = fsl_esdhc_get_cd, 1570 .send_cmd = fsl_esdhc_send_cmd, 1571 .set_ios = fsl_esdhc_set_ios, 1572 #ifdef MMC_SUPPORTS_TUNING 1573 .execute_tuning = fsl_esdhc_execute_tuning, 1574 #endif 1575 }; 1576 #endif 1577 1578 static struct esdhc_soc_data usdhc_imx7d_data = { 1579 .flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING 1580 | ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200 1581 | ESDHC_FLAG_HS400, 1582 .caps = UHS_CAPS | MMC_MODE_HS200 | MMC_MODE_DDR_52MHz | 1583 MMC_MODE_HS_52MHz | MMC_MODE_HS, 1584 }; 1585 1586 static const struct udevice_id fsl_esdhc_ids[] = { 1587 { .compatible = "fsl,imx53-esdhc", }, 1588 { .compatible = "fsl,imx6ul-usdhc", }, 1589 { .compatible = "fsl,imx6sx-usdhc", }, 1590 { .compatible = "fsl,imx6sl-usdhc", }, 1591 { .compatible = "fsl,imx6q-usdhc", }, 1592 { .compatible = "fsl,imx7d-usdhc", .data = (ulong)&usdhc_imx7d_data,}, 1593 { .compatible = "fsl,imx7ulp-usdhc", }, 1594 { .compatible = "fsl,esdhc", }, 1595 { /* sentinel */ } 1596 }; 1597 1598 #if CONFIG_IS_ENABLED(BLK) 1599 static int fsl_esdhc_bind(struct udevice *dev) 1600 { 1601 struct fsl_esdhc_plat *plat = dev_get_platdata(dev); 1602 1603 return mmc_bind(dev, &plat->mmc, &plat->cfg); 1604 } 1605 #endif 1606 1607 U_BOOT_DRIVER(fsl_esdhc) = { 1608 .name = "fsl-esdhc-mmc", 1609 .id = UCLASS_MMC, 1610 .of_match = fsl_esdhc_ids, 1611 .ops = &fsl_esdhc_ops, 1612 #if CONFIG_IS_ENABLED(BLK) 1613 .bind = fsl_esdhc_bind, 1614 #endif 1615 .probe = fsl_esdhc_probe, 1616 .platdata_auto_alloc_size = sizeof(struct fsl_esdhc_plat), 1617 .priv_auto_alloc_size = sizeof(struct fsl_esdhc_priv), 1618 }; 1619 #endif 1620