1 /* 2 * Copyright 2007, 2010-2011 Freescale Semiconductor, Inc 3 * Andy Fleming 4 * 5 * Based vaguely on the pxa mmc code: 6 * (C) Copyright 2003 7 * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net 8 * 9 * SPDX-License-Identifier: GPL-2.0+ 10 */ 11 12 #include <config.h> 13 #include <common.h> 14 #include <command.h> 15 #include <errno.h> 16 #include <hwconfig.h> 17 #include <mmc.h> 18 #include <part.h> 19 #include <malloc.h> 20 #include <fsl_esdhc.h> 21 #include <fdt_support.h> 22 #include <asm/io.h> 23 #include <dm.h> 24 #include <asm-generic/gpio.h> 25 26 DECLARE_GLOBAL_DATA_PTR; 27 28 #define SDHCI_IRQ_EN_BITS (IRQSTATEN_CC | IRQSTATEN_TC | \ 29 IRQSTATEN_CINT | \ 30 IRQSTATEN_CTOE | IRQSTATEN_CCE | IRQSTATEN_CEBE | \ 31 IRQSTATEN_CIE | IRQSTATEN_DTOE | IRQSTATEN_DCE | \ 32 IRQSTATEN_DEBE | IRQSTATEN_BRR | IRQSTATEN_BWR | \ 33 IRQSTATEN_DINT) 34 35 struct fsl_esdhc { 36 uint dsaddr; /* SDMA system address register */ 37 uint blkattr; /* Block attributes register */ 38 uint cmdarg; /* Command argument register */ 39 uint xfertyp; /* Transfer type register */ 40 uint cmdrsp0; /* Command response 0 register */ 41 uint cmdrsp1; /* Command response 1 register */ 42 uint cmdrsp2; /* Command response 2 register */ 43 uint cmdrsp3; /* Command response 3 register */ 44 uint datport; /* Buffer data port register */ 45 uint prsstat; /* Present state register */ 46 uint proctl; /* Protocol control register */ 47 uint sysctl; /* System Control Register */ 48 uint irqstat; /* Interrupt status register */ 49 uint irqstaten; /* Interrupt status enable register */ 50 uint irqsigen; /* Interrupt signal enable register */ 51 uint autoc12err; /* Auto CMD error status register */ 52 uint hostcapblt; /* Host controller capabilities register */ 53 uint wml; /* Watermark level register */ 54 uint mixctrl; /* For USDHC */ 55 char reserved1[4]; /* reserved */ 56 uint fevt; /* Force event register */ 57 uint admaes; /* ADMA error status register */ 58 uint adsaddr; /* ADMA system address register */ 59 char reserved2[4]; 60 uint dllctrl; 61 uint dllstat; 62 uint clktunectrlstatus; 63 char reserved3[84]; 64 uint vendorspec; 65 uint mmcboot; 66 uint vendorspec2; 67 char reserved4[48]; 68 uint hostver; /* Host controller version register */ 69 char reserved5[4]; /* reserved */ 70 uint dmaerraddr; /* DMA error address register */ 71 char reserved6[4]; /* reserved */ 72 uint dmaerrattr; /* DMA error attribute register */ 73 char reserved7[4]; /* reserved */ 74 uint hostcapblt2; /* Host controller capabilities register 2 */ 75 char reserved8[8]; /* reserved */ 76 uint tcr; /* Tuning control register */ 77 char reserved9[28]; /* reserved */ 78 uint sddirctl; /* SD direction control register */ 79 char reserved10[712];/* reserved */ 80 uint scr; /* eSDHC control register */ 81 }; 82 83 /** 84 * struct fsl_esdhc_priv 85 * 86 * @esdhc_regs: registers of the sdhc controller 87 * @sdhc_clk: Current clk of the sdhc controller 88 * @bus_width: bus width, 1bit, 4bit or 8bit 89 * @cfg: mmc config 90 * @mmc: mmc 91 * Following is used when Driver Model is enabled for MMC 92 * @dev: pointer for the device 93 * @non_removable: 0: removable; 1: non-removable 94 * @wp_enable: 1: enable checking wp; 0: no check 95 * @cd_gpio: gpio for card detection 96 * @wp_gpio: gpio for write protection 97 */ 98 struct fsl_esdhc_priv { 99 struct fsl_esdhc *esdhc_regs; 100 unsigned int sdhc_clk; 101 unsigned int bus_width; 102 struct mmc_config cfg; 103 struct mmc *mmc; 104 struct udevice *dev; 105 int non_removable; 106 int wp_enable; 107 #ifdef CONFIG_DM_GPIO 108 struct gpio_desc cd_gpio; 109 struct gpio_desc wp_gpio; 110 #endif 111 }; 112 113 /* Return the XFERTYP flags for a given command and data packet */ 114 static uint esdhc_xfertyp(struct mmc_cmd *cmd, struct mmc_data *data) 115 { 116 uint xfertyp = 0; 117 118 if (data) { 119 xfertyp |= XFERTYP_DPSEL; 120 #ifndef CONFIG_SYS_FSL_ESDHC_USE_PIO 121 xfertyp |= XFERTYP_DMAEN; 122 #endif 123 if (data->blocks > 1) { 124 xfertyp |= XFERTYP_MSBSEL; 125 xfertyp |= XFERTYP_BCEN; 126 #ifdef CONFIG_SYS_FSL_ERRATUM_ESDHC111 127 xfertyp |= XFERTYP_AC12EN; 128 #endif 129 } 130 131 if (data->flags & MMC_DATA_READ) 132 xfertyp |= XFERTYP_DTDSEL; 133 } 134 135 if (cmd->resp_type & MMC_RSP_CRC) 136 xfertyp |= XFERTYP_CCCEN; 137 if (cmd->resp_type & MMC_RSP_OPCODE) 138 xfertyp |= XFERTYP_CICEN; 139 if (cmd->resp_type & MMC_RSP_136) 140 xfertyp |= XFERTYP_RSPTYP_136; 141 else if (cmd->resp_type & MMC_RSP_BUSY) 142 xfertyp |= XFERTYP_RSPTYP_48_BUSY; 143 else if (cmd->resp_type & MMC_RSP_PRESENT) 144 xfertyp |= XFERTYP_RSPTYP_48; 145 146 if (cmd->cmdidx == MMC_CMD_STOP_TRANSMISSION) 147 xfertyp |= XFERTYP_CMDTYP_ABORT; 148 149 return XFERTYP_CMD(cmd->cmdidx) | xfertyp; 150 } 151 152 #ifdef CONFIG_SYS_FSL_ESDHC_USE_PIO 153 /* 154 * PIO Read/Write Mode reduce the performace as DMA is not used in this mode. 155 */ 156 static void 157 esdhc_pio_read_write(struct mmc *mmc, struct mmc_data *data) 158 { 159 struct fsl_esdhc_priv *priv = mmc->priv; 160 struct fsl_esdhc *regs = priv->esdhc_regs; 161 uint blocks; 162 char *buffer; 163 uint databuf; 164 uint size; 165 uint irqstat; 166 uint timeout; 167 168 if (data->flags & MMC_DATA_READ) { 169 blocks = data->blocks; 170 buffer = data->dest; 171 while (blocks) { 172 timeout = PIO_TIMEOUT; 173 size = data->blocksize; 174 irqstat = esdhc_read32(®s->irqstat); 175 while (!(esdhc_read32(®s->prsstat) & PRSSTAT_BREN) 176 && --timeout); 177 if (timeout <= 0) { 178 printf("\nData Read Failed in PIO Mode."); 179 return; 180 } 181 while (size && (!(irqstat & IRQSTAT_TC))) { 182 udelay(100); /* Wait before last byte transfer complete */ 183 irqstat = esdhc_read32(®s->irqstat); 184 databuf = in_le32(®s->datport); 185 *((uint *)buffer) = databuf; 186 buffer += 4; 187 size -= 4; 188 } 189 blocks--; 190 } 191 } else { 192 blocks = data->blocks; 193 buffer = (char *)data->src; 194 while (blocks) { 195 timeout = PIO_TIMEOUT; 196 size = data->blocksize; 197 irqstat = esdhc_read32(®s->irqstat); 198 while (!(esdhc_read32(®s->prsstat) & PRSSTAT_BWEN) 199 && --timeout); 200 if (timeout <= 0) { 201 printf("\nData Write Failed in PIO Mode."); 202 return; 203 } 204 while (size && (!(irqstat & IRQSTAT_TC))) { 205 udelay(100); /* Wait before last byte transfer complete */ 206 databuf = *((uint *)buffer); 207 buffer += 4; 208 size -= 4; 209 irqstat = esdhc_read32(®s->irqstat); 210 out_le32(®s->datport, databuf); 211 } 212 blocks--; 213 } 214 } 215 } 216 #endif 217 218 static int esdhc_setup_data(struct mmc *mmc, struct mmc_data *data) 219 { 220 int timeout; 221 struct fsl_esdhc_priv *priv = mmc->priv; 222 struct fsl_esdhc *regs = priv->esdhc_regs; 223 #if defined(CONFIG_FSL_LAYERSCAPE) || defined(CONFIG_S32V234) 224 dma_addr_t addr; 225 #endif 226 uint wml_value; 227 228 wml_value = data->blocksize/4; 229 230 if (data->flags & MMC_DATA_READ) { 231 if (wml_value > WML_RD_WML_MAX) 232 wml_value = WML_RD_WML_MAX_VAL; 233 234 esdhc_clrsetbits32(®s->wml, WML_RD_WML_MASK, wml_value); 235 #ifndef CONFIG_SYS_FSL_ESDHC_USE_PIO 236 #if defined(CONFIG_FSL_LAYERSCAPE) || defined(CONFIG_S32V234) 237 addr = virt_to_phys((void *)(data->dest)); 238 if (upper_32_bits(addr)) 239 printf("Error found for upper 32 bits\n"); 240 else 241 esdhc_write32(®s->dsaddr, lower_32_bits(addr)); 242 #else 243 esdhc_write32(®s->dsaddr, (u32)data->dest); 244 #endif 245 #endif 246 } else { 247 #ifndef CONFIG_SYS_FSL_ESDHC_USE_PIO 248 flush_dcache_range((ulong)data->src, 249 (ulong)data->src+data->blocks 250 *data->blocksize); 251 #endif 252 if (wml_value > WML_WR_WML_MAX) 253 wml_value = WML_WR_WML_MAX_VAL; 254 if (priv->wp_enable) { 255 if ((esdhc_read32(®s->prsstat) & 256 PRSSTAT_WPSPL) == 0) { 257 printf("\nThe SD card is locked. Can not write to a locked card.\n\n"); 258 return -ETIMEDOUT; 259 } 260 } 261 262 esdhc_clrsetbits32(®s->wml, WML_WR_WML_MASK, 263 wml_value << 16); 264 #ifndef CONFIG_SYS_FSL_ESDHC_USE_PIO 265 #if defined(CONFIG_FSL_LAYERSCAPE) || defined(CONFIG_S32V234) 266 addr = virt_to_phys((void *)(data->src)); 267 if (upper_32_bits(addr)) 268 printf("Error found for upper 32 bits\n"); 269 else 270 esdhc_write32(®s->dsaddr, lower_32_bits(addr)); 271 #else 272 esdhc_write32(®s->dsaddr, (u32)data->src); 273 #endif 274 #endif 275 } 276 277 esdhc_write32(®s->blkattr, data->blocks << 16 | data->blocksize); 278 279 /* Calculate the timeout period for data transactions */ 280 /* 281 * 1)Timeout period = (2^(timeout+13)) SD Clock cycles 282 * 2)Timeout period should be minimum 0.250sec as per SD Card spec 283 * So, Number of SD Clock cycles for 0.25sec should be minimum 284 * (SD Clock/sec * 0.25 sec) SD Clock cycles 285 * = (mmc->clock * 1/4) SD Clock cycles 286 * As 1) >= 2) 287 * => (2^(timeout+13)) >= mmc->clock * 1/4 288 * Taking log2 both the sides 289 * => timeout + 13 >= log2(mmc->clock/4) 290 * Rounding up to next power of 2 291 * => timeout + 13 = log2(mmc->clock/4) + 1 292 * => timeout + 13 = fls(mmc->clock/4) 293 * 294 * However, the MMC spec "It is strongly recommended for hosts to 295 * implement more than 500ms timeout value even if the card 296 * indicates the 250ms maximum busy length." Even the previous 297 * value of 300ms is known to be insufficient for some cards. 298 * So, we use 299 * => timeout + 13 = fls(mmc->clock/2) 300 */ 301 timeout = fls(mmc->clock/2); 302 timeout -= 13; 303 304 if (timeout > 14) 305 timeout = 14; 306 307 if (timeout < 0) 308 timeout = 0; 309 310 #ifdef CONFIG_SYS_FSL_ERRATUM_ESDHC_A001 311 if ((timeout == 4) || (timeout == 8) || (timeout == 12)) 312 timeout++; 313 #endif 314 315 #ifdef ESDHCI_QUIRK_BROKEN_TIMEOUT_VALUE 316 timeout = 0xE; 317 #endif 318 esdhc_clrsetbits32(®s->sysctl, SYSCTL_TIMEOUT_MASK, timeout << 16); 319 320 return 0; 321 } 322 323 static void check_and_invalidate_dcache_range 324 (struct mmc_cmd *cmd, 325 struct mmc_data *data) { 326 unsigned start = 0; 327 unsigned end = 0; 328 unsigned size = roundup(ARCH_DMA_MINALIGN, 329 data->blocks*data->blocksize); 330 #if defined(CONFIG_FSL_LAYERSCAPE) || defined(CONFIG_S32V234) 331 dma_addr_t addr; 332 333 addr = virt_to_phys((void *)(data->dest)); 334 if (upper_32_bits(addr)) 335 printf("Error found for upper 32 bits\n"); 336 else 337 start = lower_32_bits(addr); 338 #else 339 start = (unsigned)data->dest; 340 #endif 341 end = start + size; 342 invalidate_dcache_range(start, end); 343 } 344 345 /* 346 * Sends a command out on the bus. Takes the mmc pointer, 347 * a command pointer, and an optional data pointer. 348 */ 349 static int 350 esdhc_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd, struct mmc_data *data) 351 { 352 int err = 0; 353 uint xfertyp; 354 uint irqstat; 355 struct fsl_esdhc_priv *priv = mmc->priv; 356 struct fsl_esdhc *regs = priv->esdhc_regs; 357 358 #ifdef CONFIG_SYS_FSL_ERRATUM_ESDHC111 359 if (cmd->cmdidx == MMC_CMD_STOP_TRANSMISSION) 360 return 0; 361 #endif 362 363 esdhc_write32(®s->irqstat, -1); 364 365 sync(); 366 367 /* Wait for the bus to be idle */ 368 while ((esdhc_read32(®s->prsstat) & PRSSTAT_CICHB) || 369 (esdhc_read32(®s->prsstat) & PRSSTAT_CIDHB)) 370 ; 371 372 while (esdhc_read32(®s->prsstat) & PRSSTAT_DLA) 373 ; 374 375 /* Wait at least 8 SD clock cycles before the next command */ 376 /* 377 * Note: This is way more than 8 cycles, but 1ms seems to 378 * resolve timing issues with some cards 379 */ 380 udelay(1000); 381 382 /* Set up for a data transfer if we have one */ 383 if (data) { 384 err = esdhc_setup_data(mmc, data); 385 if(err) 386 return err; 387 388 if (data->flags & MMC_DATA_READ) 389 check_and_invalidate_dcache_range(cmd, data); 390 } 391 392 /* Figure out the transfer arguments */ 393 xfertyp = esdhc_xfertyp(cmd, data); 394 395 /* Mask all irqs */ 396 esdhc_write32(®s->irqsigen, 0); 397 398 /* Send the command */ 399 esdhc_write32(®s->cmdarg, cmd->cmdarg); 400 #if defined(CONFIG_FSL_USDHC) 401 esdhc_write32(®s->mixctrl, 402 (esdhc_read32(®s->mixctrl) & 0xFFFFFF80) | (xfertyp & 0x7F) 403 | (mmc->ddr_mode ? XFERTYP_DDREN : 0)); 404 esdhc_write32(®s->xfertyp, xfertyp & 0xFFFF0000); 405 #else 406 esdhc_write32(®s->xfertyp, xfertyp); 407 #endif 408 409 /* Wait for the command to complete */ 410 while (!(esdhc_read32(®s->irqstat) & (IRQSTAT_CC | IRQSTAT_CTOE))) 411 ; 412 413 irqstat = esdhc_read32(®s->irqstat); 414 415 if (irqstat & CMD_ERR) { 416 err = -ECOMM; 417 goto out; 418 } 419 420 if (irqstat & IRQSTAT_CTOE) { 421 err = -ETIMEDOUT; 422 goto out; 423 } 424 425 /* Switch voltage to 1.8V if CMD11 succeeded */ 426 if (cmd->cmdidx == SD_CMD_SWITCH_UHS18V) { 427 esdhc_setbits32(®s->vendorspec, ESDHC_VENDORSPEC_VSELECT); 428 429 printf("Run CMD11 1.8V switch\n"); 430 /* Sleep for 5 ms - max time for card to switch to 1.8V */ 431 udelay(5000); 432 } 433 434 /* Workaround for ESDHC errata ENGcm03648 */ 435 if (!data && (cmd->resp_type & MMC_RSP_BUSY)) { 436 int timeout = 6000; 437 438 /* Poll on DATA0 line for cmd with busy signal for 600 ms */ 439 while (timeout > 0 && !(esdhc_read32(®s->prsstat) & 440 PRSSTAT_DAT0)) { 441 udelay(100); 442 timeout--; 443 } 444 445 if (timeout <= 0) { 446 printf("Timeout waiting for DAT0 to go high!\n"); 447 err = -ETIMEDOUT; 448 goto out; 449 } 450 } 451 452 /* Copy the response to the response buffer */ 453 if (cmd->resp_type & MMC_RSP_136) { 454 u32 cmdrsp3, cmdrsp2, cmdrsp1, cmdrsp0; 455 456 cmdrsp3 = esdhc_read32(®s->cmdrsp3); 457 cmdrsp2 = esdhc_read32(®s->cmdrsp2); 458 cmdrsp1 = esdhc_read32(®s->cmdrsp1); 459 cmdrsp0 = esdhc_read32(®s->cmdrsp0); 460 cmd->response[0] = (cmdrsp3 << 8) | (cmdrsp2 >> 24); 461 cmd->response[1] = (cmdrsp2 << 8) | (cmdrsp1 >> 24); 462 cmd->response[2] = (cmdrsp1 << 8) | (cmdrsp0 >> 24); 463 cmd->response[3] = (cmdrsp0 << 8); 464 } else 465 cmd->response[0] = esdhc_read32(®s->cmdrsp0); 466 467 /* Wait until all of the blocks are transferred */ 468 if (data) { 469 #ifdef CONFIG_SYS_FSL_ESDHC_USE_PIO 470 esdhc_pio_read_write(mmc, data); 471 #else 472 do { 473 irqstat = esdhc_read32(®s->irqstat); 474 475 if (irqstat & IRQSTAT_DTOE) { 476 err = -ETIMEDOUT; 477 goto out; 478 } 479 480 if (irqstat & DATA_ERR) { 481 err = -ECOMM; 482 goto out; 483 } 484 } while ((irqstat & DATA_COMPLETE) != DATA_COMPLETE); 485 486 /* 487 * Need invalidate the dcache here again to avoid any 488 * cache-fill during the DMA operations such as the 489 * speculative pre-fetching etc. 490 */ 491 if (data->flags & MMC_DATA_READ) 492 check_and_invalidate_dcache_range(cmd, data); 493 #endif 494 } 495 496 out: 497 /* Reset CMD and DATA portions on error */ 498 if (err) { 499 esdhc_write32(®s->sysctl, esdhc_read32(®s->sysctl) | 500 SYSCTL_RSTC); 501 while (esdhc_read32(®s->sysctl) & SYSCTL_RSTC) 502 ; 503 504 if (data) { 505 esdhc_write32(®s->sysctl, 506 esdhc_read32(®s->sysctl) | 507 SYSCTL_RSTD); 508 while ((esdhc_read32(®s->sysctl) & SYSCTL_RSTD)) 509 ; 510 } 511 512 /* If this was CMD11, then notify that power cycle is needed */ 513 if (cmd->cmdidx == SD_CMD_SWITCH_UHS18V) 514 printf("CMD11 to switch to 1.8V mode failed, card requires power cycle.\n"); 515 } 516 517 esdhc_write32(®s->irqstat, -1); 518 519 return err; 520 } 521 522 static void set_sysctl(struct mmc *mmc, uint clock) 523 { 524 int div, pre_div; 525 struct fsl_esdhc_priv *priv = mmc->priv; 526 struct fsl_esdhc *regs = priv->esdhc_regs; 527 int sdhc_clk = priv->sdhc_clk; 528 uint clk; 529 530 if (clock < mmc->cfg->f_min) 531 clock = mmc->cfg->f_min; 532 533 if (sdhc_clk / 16 > clock) { 534 for (pre_div = 2; pre_div < 256; pre_div *= 2) 535 if ((sdhc_clk / pre_div) <= (clock * 16)) 536 break; 537 } else 538 pre_div = 2; 539 540 for (div = 1; div <= 16; div++) 541 if ((sdhc_clk / (div * pre_div)) <= clock) 542 break; 543 544 pre_div >>= mmc->ddr_mode ? 2 : 1; 545 div -= 1; 546 547 clk = (pre_div << 8) | (div << 4); 548 549 #ifdef CONFIG_FSL_USDHC 550 esdhc_clrbits32(®s->vendorspec, VENDORSPEC_CKEN); 551 #else 552 esdhc_clrbits32(®s->sysctl, SYSCTL_CKEN); 553 #endif 554 555 esdhc_clrsetbits32(®s->sysctl, SYSCTL_CLOCK_MASK, clk); 556 557 udelay(10000); 558 559 #ifdef CONFIG_FSL_USDHC 560 esdhc_setbits32(®s->vendorspec, VENDORSPEC_PEREN | VENDORSPEC_CKEN); 561 #else 562 esdhc_setbits32(®s->sysctl, SYSCTL_PEREN | SYSCTL_CKEN); 563 #endif 564 565 } 566 567 #ifdef CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK 568 static void esdhc_clock_control(struct mmc *mmc, bool enable) 569 { 570 struct fsl_esdhc_priv *priv = mmc->priv; 571 struct fsl_esdhc *regs = priv->esdhc_regs; 572 u32 value; 573 u32 time_out; 574 575 value = esdhc_read32(®s->sysctl); 576 577 if (enable) 578 value |= SYSCTL_CKEN; 579 else 580 value &= ~SYSCTL_CKEN; 581 582 esdhc_write32(®s->sysctl, value); 583 584 time_out = 20; 585 value = PRSSTAT_SDSTB; 586 while (!(esdhc_read32(®s->prsstat) & value)) { 587 if (time_out == 0) { 588 printf("fsl_esdhc: Internal clock never stabilised.\n"); 589 break; 590 } 591 time_out--; 592 mdelay(1); 593 } 594 } 595 #endif 596 597 static int esdhc_set_ios(struct mmc *mmc) 598 { 599 struct fsl_esdhc_priv *priv = mmc->priv; 600 struct fsl_esdhc *regs = priv->esdhc_regs; 601 602 #ifdef CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK 603 /* Select to use peripheral clock */ 604 esdhc_clock_control(mmc, false); 605 esdhc_setbits32(®s->scr, ESDHCCTL_PCS); 606 esdhc_clock_control(mmc, true); 607 #endif 608 /* Set the clock speed */ 609 set_sysctl(mmc, mmc->clock); 610 611 /* Set the bus width */ 612 esdhc_clrbits32(®s->proctl, PROCTL_DTW_4 | PROCTL_DTW_8); 613 614 if (mmc->bus_width == 4) 615 esdhc_setbits32(®s->proctl, PROCTL_DTW_4); 616 else if (mmc->bus_width == 8) 617 esdhc_setbits32(®s->proctl, PROCTL_DTW_8); 618 619 return 0; 620 } 621 622 static int esdhc_init(struct mmc *mmc) 623 { 624 struct fsl_esdhc_priv *priv = mmc->priv; 625 struct fsl_esdhc *regs = priv->esdhc_regs; 626 int timeout = 1000; 627 628 /* Reset the entire host controller */ 629 esdhc_setbits32(®s->sysctl, SYSCTL_RSTA); 630 631 /* Wait until the controller is available */ 632 while ((esdhc_read32(®s->sysctl) & SYSCTL_RSTA) && --timeout) 633 udelay(1000); 634 635 #if defined(CONFIG_FSL_USDHC) 636 /* RSTA doesn't reset MMC_BOOT register, so manually reset it */ 637 esdhc_write32(®s->mmcboot, 0x0); 638 /* Reset MIX_CTRL and CLK_TUNE_CTRL_STATUS regs to 0 */ 639 esdhc_write32(®s->mixctrl, 0x0); 640 esdhc_write32(®s->clktunectrlstatus, 0x0); 641 642 /* Put VEND_SPEC to default value */ 643 esdhc_write32(®s->vendorspec, VENDORSPEC_INIT); 644 645 /* Disable DLL_CTRL delay line */ 646 esdhc_write32(®s->dllctrl, 0x0); 647 #endif 648 649 #ifndef ARCH_MXC 650 /* Enable cache snooping */ 651 esdhc_write32(®s->scr, 0x00000040); 652 #endif 653 654 #ifndef CONFIG_FSL_USDHC 655 esdhc_setbits32(®s->sysctl, SYSCTL_HCKEN | SYSCTL_IPGEN); 656 #else 657 esdhc_setbits32(®s->vendorspec, VENDORSPEC_HCKEN | VENDORSPEC_IPGEN); 658 #endif 659 660 /* Set the initial clock speed */ 661 mmc_set_clock(mmc, 400000); 662 663 /* Disable the BRR and BWR bits in IRQSTAT */ 664 esdhc_clrbits32(®s->irqstaten, IRQSTATEN_BRR | IRQSTATEN_BWR); 665 666 /* Put the PROCTL reg back to the default */ 667 esdhc_write32(®s->proctl, PROCTL_INIT); 668 669 /* Set timout to the maximum value */ 670 esdhc_clrsetbits32(®s->sysctl, SYSCTL_TIMEOUT_MASK, 14 << 16); 671 672 #ifdef CONFIG_SYS_FSL_ESDHC_FORCE_VSELECT 673 esdhc_setbits32(®s->vendorspec, ESDHC_VENDORSPEC_VSELECT); 674 #endif 675 676 return 0; 677 } 678 679 static int esdhc_getcd(struct mmc *mmc) 680 { 681 struct fsl_esdhc_priv *priv = mmc->priv; 682 struct fsl_esdhc *regs = priv->esdhc_regs; 683 int timeout = 1000; 684 685 #ifdef CONFIG_ESDHC_DETECT_QUIRK 686 if (CONFIG_ESDHC_DETECT_QUIRK) 687 return 1; 688 #endif 689 690 #ifdef CONFIG_DM_MMC 691 if (priv->non_removable) 692 return 1; 693 #ifdef CONFIG_DM_GPIO 694 if (dm_gpio_is_valid(&priv->cd_gpio)) 695 return dm_gpio_get_value(&priv->cd_gpio); 696 #endif 697 #endif 698 699 while (!(esdhc_read32(®s->prsstat) & PRSSTAT_CINS) && --timeout) 700 udelay(1000); 701 702 return timeout > 0; 703 } 704 705 static void esdhc_reset(struct fsl_esdhc *regs) 706 { 707 unsigned long timeout = 100; /* wait max 100 ms */ 708 709 /* reset the controller */ 710 esdhc_setbits32(®s->sysctl, SYSCTL_RSTA); 711 712 /* hardware clears the bit when it is done */ 713 while ((esdhc_read32(®s->sysctl) & SYSCTL_RSTA) && --timeout) 714 udelay(1000); 715 if (!timeout) 716 printf("MMC/SD: Reset never completed.\n"); 717 } 718 719 static const struct mmc_ops esdhc_ops = { 720 .send_cmd = esdhc_send_cmd, 721 .set_ios = esdhc_set_ios, 722 .init = esdhc_init, 723 .getcd = esdhc_getcd, 724 }; 725 726 static int fsl_esdhc_cfg_to_priv(struct fsl_esdhc_cfg *cfg, 727 struct fsl_esdhc_priv *priv) 728 { 729 if (!cfg || !priv) 730 return -EINVAL; 731 732 priv->esdhc_regs = (struct fsl_esdhc *)(unsigned long)(cfg->esdhc_base); 733 priv->bus_width = cfg->max_bus_width; 734 priv->sdhc_clk = cfg->sdhc_clk; 735 priv->wp_enable = cfg->wp_enable; 736 737 return 0; 738 }; 739 740 static int fsl_esdhc_init(struct fsl_esdhc_priv *priv) 741 { 742 struct fsl_esdhc *regs; 743 struct mmc *mmc; 744 u32 caps, voltage_caps; 745 746 if (!priv) 747 return -EINVAL; 748 749 regs = priv->esdhc_regs; 750 751 /* First reset the eSDHC controller */ 752 esdhc_reset(regs); 753 754 #ifndef CONFIG_FSL_USDHC 755 esdhc_setbits32(®s->sysctl, SYSCTL_PEREN | SYSCTL_HCKEN 756 | SYSCTL_IPGEN | SYSCTL_CKEN); 757 #else 758 esdhc_setbits32(®s->vendorspec, VENDORSPEC_PEREN | 759 VENDORSPEC_HCKEN | VENDORSPEC_IPGEN | VENDORSPEC_CKEN); 760 #endif 761 762 writel(SDHCI_IRQ_EN_BITS, ®s->irqstaten); 763 memset(&priv->cfg, 0, sizeof(priv->cfg)); 764 765 voltage_caps = 0; 766 caps = esdhc_read32(®s->hostcapblt); 767 768 #ifdef CONFIG_SYS_FSL_ERRATUM_ESDHC135 769 caps = caps & ~(ESDHC_HOSTCAPBLT_SRS | 770 ESDHC_HOSTCAPBLT_VS18 | ESDHC_HOSTCAPBLT_VS30); 771 #endif 772 773 /* T4240 host controller capabilities register should have VS33 bit */ 774 #ifdef CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 775 caps = caps | ESDHC_HOSTCAPBLT_VS33; 776 #endif 777 778 if (caps & ESDHC_HOSTCAPBLT_VS18) 779 voltage_caps |= MMC_VDD_165_195; 780 if (caps & ESDHC_HOSTCAPBLT_VS30) 781 voltage_caps |= MMC_VDD_29_30 | MMC_VDD_30_31; 782 if (caps & ESDHC_HOSTCAPBLT_VS33) 783 voltage_caps |= MMC_VDD_32_33 | MMC_VDD_33_34; 784 785 priv->cfg.name = "FSL_SDHC"; 786 priv->cfg.ops = &esdhc_ops; 787 #ifdef CONFIG_SYS_SD_VOLTAGE 788 priv->cfg.voltages = CONFIG_SYS_SD_VOLTAGE; 789 #else 790 priv->cfg.voltages = MMC_VDD_32_33 | MMC_VDD_33_34; 791 #endif 792 if ((priv->cfg.voltages & voltage_caps) == 0) { 793 printf("voltage not supported by controller\n"); 794 return -1; 795 } 796 797 if (priv->bus_width == 8) 798 priv->cfg.host_caps = MMC_MODE_4BIT | MMC_MODE_8BIT; 799 else if (priv->bus_width == 4) 800 priv->cfg.host_caps = MMC_MODE_4BIT; 801 802 priv->cfg.host_caps = MMC_MODE_4BIT | MMC_MODE_8BIT; 803 #ifdef CONFIG_SYS_FSL_ESDHC_HAS_DDR_MODE 804 priv->cfg.host_caps |= MMC_MODE_DDR_52MHz; 805 #endif 806 807 if (priv->bus_width > 0) { 808 if (priv->bus_width < 8) 809 priv->cfg.host_caps &= ~MMC_MODE_8BIT; 810 if (priv->bus_width < 4) 811 priv->cfg.host_caps &= ~MMC_MODE_4BIT; 812 } 813 814 if (caps & ESDHC_HOSTCAPBLT_HSS) 815 priv->cfg.host_caps |= MMC_MODE_HS_52MHz | MMC_MODE_HS; 816 817 #ifdef CONFIG_ESDHC_DETECT_8_BIT_QUIRK 818 if (CONFIG_ESDHC_DETECT_8_BIT_QUIRK) 819 priv->cfg.host_caps &= ~MMC_MODE_8BIT; 820 #endif 821 822 priv->cfg.f_min = 400000; 823 priv->cfg.f_max = min(priv->sdhc_clk, (u32)52000000); 824 825 priv->cfg.b_max = CONFIG_SYS_MMC_MAX_BLK_COUNT; 826 827 mmc = mmc_create(&priv->cfg, priv); 828 if (mmc == NULL) 829 return -1; 830 831 priv->mmc = mmc; 832 833 return 0; 834 } 835 836 int fsl_esdhc_initialize(bd_t *bis, struct fsl_esdhc_cfg *cfg) 837 { 838 struct fsl_esdhc_priv *priv; 839 int ret; 840 841 if (!cfg) 842 return -EINVAL; 843 844 priv = calloc(sizeof(struct fsl_esdhc_priv), 1); 845 if (!priv) 846 return -ENOMEM; 847 848 ret = fsl_esdhc_cfg_to_priv(cfg, priv); 849 if (ret) { 850 debug("%s xlate failure\n", __func__); 851 free(priv); 852 return ret; 853 } 854 855 ret = fsl_esdhc_init(priv); 856 if (ret) { 857 debug("%s init failure\n", __func__); 858 free(priv); 859 return ret; 860 } 861 862 return 0; 863 } 864 865 int fsl_esdhc_mmc_init(bd_t *bis) 866 { 867 struct fsl_esdhc_cfg *cfg; 868 869 cfg = calloc(sizeof(struct fsl_esdhc_cfg), 1); 870 cfg->esdhc_base = CONFIG_SYS_FSL_ESDHC_ADDR; 871 cfg->sdhc_clk = gd->arch.sdhc_clk; 872 return fsl_esdhc_initialize(bis, cfg); 873 } 874 875 #ifdef CONFIG_FSL_ESDHC_ADAPTER_IDENT 876 void mmc_adapter_card_type_ident(void) 877 { 878 u8 card_id; 879 u8 value; 880 881 card_id = QIXIS_READ(present) & QIXIS_SDID_MASK; 882 gd->arch.sdhc_adapter = card_id; 883 884 switch (card_id) { 885 case QIXIS_ESDHC_ADAPTER_TYPE_EMMC45: 886 value = QIXIS_READ(brdcfg[5]); 887 value |= (QIXIS_DAT4 | QIXIS_DAT5_6_7); 888 QIXIS_WRITE(brdcfg[5], value); 889 break; 890 case QIXIS_ESDHC_ADAPTER_TYPE_SDMMC_LEGACY: 891 value = QIXIS_READ(pwr_ctl[1]); 892 value |= QIXIS_EVDD_BY_SDHC_VS; 893 QIXIS_WRITE(pwr_ctl[1], value); 894 break; 895 case QIXIS_ESDHC_ADAPTER_TYPE_EMMC44: 896 value = QIXIS_READ(brdcfg[5]); 897 value |= (QIXIS_SDCLKIN | QIXIS_SDCLKOUT); 898 QIXIS_WRITE(brdcfg[5], value); 899 break; 900 case QIXIS_ESDHC_ADAPTER_TYPE_RSV: 901 break; 902 case QIXIS_ESDHC_ADAPTER_TYPE_MMC: 903 break; 904 case QIXIS_ESDHC_ADAPTER_TYPE_SD: 905 break; 906 case QIXIS_ESDHC_NO_ADAPTER: 907 break; 908 default: 909 break; 910 } 911 } 912 #endif 913 914 #ifdef CONFIG_OF_LIBFDT 915 __weak int esdhc_status_fixup(void *blob, const char *compat) 916 { 917 #ifdef CONFIG_FSL_ESDHC_PIN_MUX 918 if (!hwconfig("esdhc")) { 919 do_fixup_by_compat(blob, compat, "status", "disabled", 920 sizeof("disabled"), 1); 921 return 1; 922 } 923 #endif 924 do_fixup_by_compat(blob, compat, "status", "okay", 925 sizeof("okay"), 1); 926 return 0; 927 } 928 929 void fdt_fixup_esdhc(void *blob, bd_t *bd) 930 { 931 const char *compat = "fsl,esdhc"; 932 933 if (esdhc_status_fixup(blob, compat)) 934 return; 935 936 #ifdef CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK 937 do_fixup_by_compat_u32(blob, compat, "peripheral-frequency", 938 gd->arch.sdhc_clk, 1); 939 #else 940 do_fixup_by_compat_u32(blob, compat, "clock-frequency", 941 gd->arch.sdhc_clk, 1); 942 #endif 943 #ifdef CONFIG_FSL_ESDHC_ADAPTER_IDENT 944 do_fixup_by_compat_u32(blob, compat, "adapter-type", 945 (u32)(gd->arch.sdhc_adapter), 1); 946 #endif 947 } 948 #endif 949 950 #ifdef CONFIG_DM_MMC 951 #include <asm/arch/clock.h> 952 static int fsl_esdhc_probe(struct udevice *dev) 953 { 954 struct mmc_uclass_priv *upriv = dev_get_uclass_priv(dev); 955 struct fsl_esdhc_priv *priv = dev_get_priv(dev); 956 const void *fdt = gd->fdt_blob; 957 int node = dev_of_offset(dev); 958 fdt_addr_t addr; 959 unsigned int val; 960 int ret; 961 962 addr = dev_get_addr(dev); 963 if (addr == FDT_ADDR_T_NONE) 964 return -EINVAL; 965 966 priv->esdhc_regs = (struct fsl_esdhc *)addr; 967 priv->dev = dev; 968 969 val = fdtdec_get_int(fdt, node, "bus-width", -1); 970 if (val == 8) 971 priv->bus_width = 8; 972 else if (val == 4) 973 priv->bus_width = 4; 974 else 975 priv->bus_width = 1; 976 977 if (fdt_get_property(fdt, node, "non-removable", NULL)) { 978 priv->non_removable = 1; 979 } else { 980 priv->non_removable = 0; 981 #ifdef CONFIG_DM_GPIO 982 gpio_request_by_name_nodev(fdt, node, "cd-gpios", 0, 983 &priv->cd_gpio, GPIOD_IS_IN); 984 #endif 985 } 986 987 priv->wp_enable = 1; 988 989 #ifdef CONFIG_DM_GPIO 990 ret = gpio_request_by_name_nodev(fdt, node, "wp-gpios", 0, 991 &priv->wp_gpio, GPIOD_IS_IN); 992 if (ret) 993 priv->wp_enable = 0; 994 #endif 995 /* 996 * TODO: 997 * Because lack of clk driver, if SDHC clk is not enabled, 998 * need to enable it first before this driver is invoked. 999 * 1000 * we use MXC_ESDHC_CLK to get clk freq. 1001 * If one would like to make this function work, 1002 * the aliases should be provided in dts as this: 1003 * 1004 * aliases { 1005 * mmc0 = &usdhc1; 1006 * mmc1 = &usdhc2; 1007 * mmc2 = &usdhc3; 1008 * mmc3 = &usdhc4; 1009 * }; 1010 * Then if your board only supports mmc2 and mmc3, but we can 1011 * correctly get the seq as 2 and 3, then let mxc_get_clock 1012 * work as expected. 1013 */ 1014 priv->sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK + dev->seq); 1015 if (priv->sdhc_clk <= 0) { 1016 dev_err(dev, "Unable to get clk for %s\n", dev->name); 1017 return -EINVAL; 1018 } 1019 1020 ret = fsl_esdhc_init(priv); 1021 if (ret) { 1022 dev_err(dev, "fsl_esdhc_init failure\n"); 1023 return ret; 1024 } 1025 1026 upriv->mmc = priv->mmc; 1027 priv->mmc->dev = dev; 1028 1029 return 0; 1030 } 1031 1032 static const struct udevice_id fsl_esdhc_ids[] = { 1033 { .compatible = "fsl,imx6ul-usdhc", }, 1034 { .compatible = "fsl,imx6sx-usdhc", }, 1035 { .compatible = "fsl,imx6sl-usdhc", }, 1036 { .compatible = "fsl,imx6q-usdhc", }, 1037 { .compatible = "fsl,imx7d-usdhc", }, 1038 { .compatible = "fsl,esdhc", }, 1039 { /* sentinel */ } 1040 }; 1041 1042 U_BOOT_DRIVER(fsl_esdhc) = { 1043 .name = "fsl-esdhc-mmc", 1044 .id = UCLASS_MMC, 1045 .of_match = fsl_esdhc_ids, 1046 .probe = fsl_esdhc_probe, 1047 .priv_auto_alloc_size = sizeof(struct fsl_esdhc_priv), 1048 }; 1049 #endif 1050