1 /* 2 * Copyright 2007, 2010-2011 Freescale Semiconductor, Inc 3 * Andy Fleming 4 * 5 * Based vaguely on the pxa mmc code: 6 * (C) Copyright 2003 7 * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net 8 * 9 * SPDX-License-Identifier: GPL-2.0+ 10 */ 11 12 #include <config.h> 13 #include <common.h> 14 #include <command.h> 15 #include <errno.h> 16 #include <hwconfig.h> 17 #include <mmc.h> 18 #include <part.h> 19 #include <power/regulator.h> 20 #include <malloc.h> 21 #include <fsl_esdhc.h> 22 #include <fdt_support.h> 23 #include <asm/io.h> 24 #include <dm.h> 25 #include <asm-generic/gpio.h> 26 27 DECLARE_GLOBAL_DATA_PTR; 28 29 #define SDHCI_IRQ_EN_BITS (IRQSTATEN_CC | IRQSTATEN_TC | \ 30 IRQSTATEN_CINT | \ 31 IRQSTATEN_CTOE | IRQSTATEN_CCE | IRQSTATEN_CEBE | \ 32 IRQSTATEN_CIE | IRQSTATEN_DTOE | IRQSTATEN_DCE | \ 33 IRQSTATEN_DEBE | IRQSTATEN_BRR | IRQSTATEN_BWR | \ 34 IRQSTATEN_DINT) 35 36 struct fsl_esdhc { 37 uint dsaddr; /* SDMA system address register */ 38 uint blkattr; /* Block attributes register */ 39 uint cmdarg; /* Command argument register */ 40 uint xfertyp; /* Transfer type register */ 41 uint cmdrsp0; /* Command response 0 register */ 42 uint cmdrsp1; /* Command response 1 register */ 43 uint cmdrsp2; /* Command response 2 register */ 44 uint cmdrsp3; /* Command response 3 register */ 45 uint datport; /* Buffer data port register */ 46 uint prsstat; /* Present state register */ 47 uint proctl; /* Protocol control register */ 48 uint sysctl; /* System Control Register */ 49 uint irqstat; /* Interrupt status register */ 50 uint irqstaten; /* Interrupt status enable register */ 51 uint irqsigen; /* Interrupt signal enable register */ 52 uint autoc12err; /* Auto CMD error status register */ 53 uint hostcapblt; /* Host controller capabilities register */ 54 uint wml; /* Watermark level register */ 55 uint mixctrl; /* For USDHC */ 56 char reserved1[4]; /* reserved */ 57 uint fevt; /* Force event register */ 58 uint admaes; /* ADMA error status register */ 59 uint adsaddr; /* ADMA system address register */ 60 char reserved2[4]; 61 uint dllctrl; 62 uint dllstat; 63 uint clktunectrlstatus; 64 char reserved3[84]; 65 uint vendorspec; 66 uint mmcboot; 67 uint vendorspec2; 68 char reserved4[48]; 69 uint hostver; /* Host controller version register */ 70 char reserved5[4]; /* reserved */ 71 uint dmaerraddr; /* DMA error address register */ 72 char reserved6[4]; /* reserved */ 73 uint dmaerrattr; /* DMA error attribute register */ 74 char reserved7[4]; /* reserved */ 75 uint hostcapblt2; /* Host controller capabilities register 2 */ 76 char reserved8[8]; /* reserved */ 77 uint tcr; /* Tuning control register */ 78 char reserved9[28]; /* reserved */ 79 uint sddirctl; /* SD direction control register */ 80 char reserved10[712];/* reserved */ 81 uint scr; /* eSDHC control register */ 82 }; 83 84 struct fsl_esdhc_plat { 85 struct mmc_config cfg; 86 struct mmc mmc; 87 }; 88 89 /** 90 * struct fsl_esdhc_priv 91 * 92 * @esdhc_regs: registers of the sdhc controller 93 * @sdhc_clk: Current clk of the sdhc controller 94 * @bus_width: bus width, 1bit, 4bit or 8bit 95 * @cfg: mmc config 96 * @mmc: mmc 97 * Following is used when Driver Model is enabled for MMC 98 * @dev: pointer for the device 99 * @non_removable: 0: removable; 1: non-removable 100 * @wp_enable: 1: enable checking wp; 0: no check 101 * @vs18_enable: 1: use 1.8V voltage; 0: use 3.3V 102 * @cd_gpio: gpio for card detection 103 * @wp_gpio: gpio for write protection 104 */ 105 struct fsl_esdhc_priv { 106 struct fsl_esdhc *esdhc_regs; 107 unsigned int sdhc_clk; 108 unsigned int bus_width; 109 #if !CONFIG_IS_ENABLED(BLK) 110 struct mmc *mmc; 111 #endif 112 struct udevice *dev; 113 int non_removable; 114 int wp_enable; 115 int vs18_enable; 116 #ifdef CONFIG_DM_GPIO 117 struct gpio_desc cd_gpio; 118 struct gpio_desc wp_gpio; 119 #endif 120 }; 121 122 /* Return the XFERTYP flags for a given command and data packet */ 123 static uint esdhc_xfertyp(struct mmc_cmd *cmd, struct mmc_data *data) 124 { 125 uint xfertyp = 0; 126 127 if (data) { 128 xfertyp |= XFERTYP_DPSEL; 129 #ifndef CONFIG_SYS_FSL_ESDHC_USE_PIO 130 xfertyp |= XFERTYP_DMAEN; 131 #endif 132 if (data->blocks > 1) { 133 xfertyp |= XFERTYP_MSBSEL; 134 xfertyp |= XFERTYP_BCEN; 135 #ifdef CONFIG_SYS_FSL_ERRATUM_ESDHC111 136 xfertyp |= XFERTYP_AC12EN; 137 #endif 138 } 139 140 if (data->flags & MMC_DATA_READ) 141 xfertyp |= XFERTYP_DTDSEL; 142 } 143 144 if (cmd->resp_type & MMC_RSP_CRC) 145 xfertyp |= XFERTYP_CCCEN; 146 if (cmd->resp_type & MMC_RSP_OPCODE) 147 xfertyp |= XFERTYP_CICEN; 148 if (cmd->resp_type & MMC_RSP_136) 149 xfertyp |= XFERTYP_RSPTYP_136; 150 else if (cmd->resp_type & MMC_RSP_BUSY) 151 xfertyp |= XFERTYP_RSPTYP_48_BUSY; 152 else if (cmd->resp_type & MMC_RSP_PRESENT) 153 xfertyp |= XFERTYP_RSPTYP_48; 154 155 if (cmd->cmdidx == MMC_CMD_STOP_TRANSMISSION) 156 xfertyp |= XFERTYP_CMDTYP_ABORT; 157 158 return XFERTYP_CMD(cmd->cmdidx) | xfertyp; 159 } 160 161 #ifdef CONFIG_SYS_FSL_ESDHC_USE_PIO 162 /* 163 * PIO Read/Write Mode reduce the performace as DMA is not used in this mode. 164 */ 165 static void esdhc_pio_read_write(struct fsl_esdhc_priv *priv, 166 struct mmc_data *data) 167 { 168 struct fsl_esdhc *regs = priv->esdhc_regs; 169 uint blocks; 170 char *buffer; 171 uint databuf; 172 uint size; 173 uint irqstat; 174 ulong start; 175 176 if (data->flags & MMC_DATA_READ) { 177 blocks = data->blocks; 178 buffer = data->dest; 179 while (blocks) { 180 start = get_timer(0); 181 size = data->blocksize; 182 irqstat = esdhc_read32(®s->irqstat); 183 while (!(esdhc_read32(®s->prsstat) & PRSSTAT_BREN)) { 184 if (get_timer(start) > PIO_TIMEOUT) { 185 printf("\nData Read Failed in PIO Mode."); 186 return; 187 } 188 } 189 while (size && (!(irqstat & IRQSTAT_TC))) { 190 udelay(100); /* Wait before last byte transfer complete */ 191 irqstat = esdhc_read32(®s->irqstat); 192 databuf = in_le32(®s->datport); 193 *((uint *)buffer) = databuf; 194 buffer += 4; 195 size -= 4; 196 } 197 blocks--; 198 } 199 } else { 200 blocks = data->blocks; 201 buffer = (char *)data->src; 202 while (blocks) { 203 start = get_timer(0); 204 size = data->blocksize; 205 irqstat = esdhc_read32(®s->irqstat); 206 while (!(esdhc_read32(®s->prsstat) & PRSSTAT_BWEN)) { 207 if (get_timer(start) > PIO_TIMEOUT) { 208 printf("\nData Write Failed in PIO Mode."); 209 return; 210 } 211 } 212 while (size && (!(irqstat & IRQSTAT_TC))) { 213 udelay(100); /* Wait before last byte transfer complete */ 214 databuf = *((uint *)buffer); 215 buffer += 4; 216 size -= 4; 217 irqstat = esdhc_read32(®s->irqstat); 218 out_le32(®s->datport, databuf); 219 } 220 blocks--; 221 } 222 } 223 } 224 #endif 225 226 static int esdhc_setup_data(struct fsl_esdhc_priv *priv, struct mmc *mmc, 227 struct mmc_data *data) 228 { 229 int timeout; 230 struct fsl_esdhc *regs = priv->esdhc_regs; 231 #if defined(CONFIG_FSL_LAYERSCAPE) || defined(CONFIG_S32V234) 232 dma_addr_t addr; 233 #endif 234 uint wml_value; 235 236 wml_value = data->blocksize/4; 237 238 if (data->flags & MMC_DATA_READ) { 239 if (wml_value > WML_RD_WML_MAX) 240 wml_value = WML_RD_WML_MAX_VAL; 241 242 esdhc_clrsetbits32(®s->wml, WML_RD_WML_MASK, wml_value); 243 #ifndef CONFIG_SYS_FSL_ESDHC_USE_PIO 244 #if defined(CONFIG_FSL_LAYERSCAPE) || defined(CONFIG_S32V234) 245 addr = virt_to_phys((void *)(data->dest)); 246 if (upper_32_bits(addr)) 247 printf("Error found for upper 32 bits\n"); 248 else 249 esdhc_write32(®s->dsaddr, lower_32_bits(addr)); 250 #else 251 esdhc_write32(®s->dsaddr, (u32)data->dest); 252 #endif 253 #endif 254 } else { 255 #ifndef CONFIG_SYS_FSL_ESDHC_USE_PIO 256 flush_dcache_range((ulong)data->src, 257 (ulong)data->src+data->blocks 258 *data->blocksize); 259 #endif 260 if (wml_value > WML_WR_WML_MAX) 261 wml_value = WML_WR_WML_MAX_VAL; 262 if (priv->wp_enable) { 263 if ((esdhc_read32(®s->prsstat) & 264 PRSSTAT_WPSPL) == 0) { 265 printf("\nThe SD card is locked. Can not write to a locked card.\n\n"); 266 return -ETIMEDOUT; 267 } 268 } 269 270 esdhc_clrsetbits32(®s->wml, WML_WR_WML_MASK, 271 wml_value << 16); 272 #ifndef CONFIG_SYS_FSL_ESDHC_USE_PIO 273 #if defined(CONFIG_FSL_LAYERSCAPE) || defined(CONFIG_S32V234) 274 addr = virt_to_phys((void *)(data->src)); 275 if (upper_32_bits(addr)) 276 printf("Error found for upper 32 bits\n"); 277 else 278 esdhc_write32(®s->dsaddr, lower_32_bits(addr)); 279 #else 280 esdhc_write32(®s->dsaddr, (u32)data->src); 281 #endif 282 #endif 283 } 284 285 esdhc_write32(®s->blkattr, data->blocks << 16 | data->blocksize); 286 287 /* Calculate the timeout period for data transactions */ 288 /* 289 * 1)Timeout period = (2^(timeout+13)) SD Clock cycles 290 * 2)Timeout period should be minimum 0.250sec as per SD Card spec 291 * So, Number of SD Clock cycles for 0.25sec should be minimum 292 * (SD Clock/sec * 0.25 sec) SD Clock cycles 293 * = (mmc->clock * 1/4) SD Clock cycles 294 * As 1) >= 2) 295 * => (2^(timeout+13)) >= mmc->clock * 1/4 296 * Taking log2 both the sides 297 * => timeout + 13 >= log2(mmc->clock/4) 298 * Rounding up to next power of 2 299 * => timeout + 13 = log2(mmc->clock/4) + 1 300 * => timeout + 13 = fls(mmc->clock/4) 301 * 302 * However, the MMC spec "It is strongly recommended for hosts to 303 * implement more than 500ms timeout value even if the card 304 * indicates the 250ms maximum busy length." Even the previous 305 * value of 300ms is known to be insufficient for some cards. 306 * So, we use 307 * => timeout + 13 = fls(mmc->clock/2) 308 */ 309 timeout = fls(mmc->clock/2); 310 timeout -= 13; 311 312 if (timeout > 14) 313 timeout = 14; 314 315 if (timeout < 0) 316 timeout = 0; 317 318 #ifdef CONFIG_SYS_FSL_ERRATUM_ESDHC_A001 319 if ((timeout == 4) || (timeout == 8) || (timeout == 12)) 320 timeout++; 321 #endif 322 323 #ifdef ESDHCI_QUIRK_BROKEN_TIMEOUT_VALUE 324 timeout = 0xE; 325 #endif 326 esdhc_clrsetbits32(®s->sysctl, SYSCTL_TIMEOUT_MASK, timeout << 16); 327 328 return 0; 329 } 330 331 static void check_and_invalidate_dcache_range 332 (struct mmc_cmd *cmd, 333 struct mmc_data *data) { 334 unsigned start = 0; 335 unsigned end = 0; 336 unsigned size = roundup(ARCH_DMA_MINALIGN, 337 data->blocks*data->blocksize); 338 #if defined(CONFIG_FSL_LAYERSCAPE) || defined(CONFIG_S32V234) 339 dma_addr_t addr; 340 341 addr = virt_to_phys((void *)(data->dest)); 342 if (upper_32_bits(addr)) 343 printf("Error found for upper 32 bits\n"); 344 else 345 start = lower_32_bits(addr); 346 #else 347 start = (unsigned)data->dest; 348 #endif 349 end = start + size; 350 invalidate_dcache_range(start, end); 351 } 352 353 /* 354 * Sends a command out on the bus. Takes the mmc pointer, 355 * a command pointer, and an optional data pointer. 356 */ 357 static int esdhc_send_cmd_common(struct fsl_esdhc_priv *priv, struct mmc *mmc, 358 struct mmc_cmd *cmd, struct mmc_data *data) 359 { 360 int err = 0; 361 uint xfertyp; 362 uint irqstat; 363 struct fsl_esdhc *regs = priv->esdhc_regs; 364 365 #ifdef CONFIG_SYS_FSL_ERRATUM_ESDHC111 366 if (cmd->cmdidx == MMC_CMD_STOP_TRANSMISSION) 367 return 0; 368 #endif 369 370 esdhc_write32(®s->irqstat, -1); 371 372 sync(); 373 374 /* Wait for the bus to be idle */ 375 while ((esdhc_read32(®s->prsstat) & PRSSTAT_CICHB) || 376 (esdhc_read32(®s->prsstat) & PRSSTAT_CIDHB)) 377 ; 378 379 while (esdhc_read32(®s->prsstat) & PRSSTAT_DLA) 380 ; 381 382 /* Wait at least 8 SD clock cycles before the next command */ 383 /* 384 * Note: This is way more than 8 cycles, but 1ms seems to 385 * resolve timing issues with some cards 386 */ 387 udelay(1000); 388 389 /* Set up for a data transfer if we have one */ 390 if (data) { 391 err = esdhc_setup_data(priv, mmc, data); 392 if(err) 393 return err; 394 395 if (data->flags & MMC_DATA_READ) 396 check_and_invalidate_dcache_range(cmd, data); 397 } 398 399 /* Figure out the transfer arguments */ 400 xfertyp = esdhc_xfertyp(cmd, data); 401 402 /* Mask all irqs */ 403 esdhc_write32(®s->irqsigen, 0); 404 405 /* Send the command */ 406 esdhc_write32(®s->cmdarg, cmd->cmdarg); 407 #if defined(CONFIG_FSL_USDHC) 408 esdhc_write32(®s->mixctrl, 409 (esdhc_read32(®s->mixctrl) & 0xFFFFFF80) | (xfertyp & 0x7F) 410 | (mmc->ddr_mode ? XFERTYP_DDREN : 0)); 411 esdhc_write32(®s->xfertyp, xfertyp & 0xFFFF0000); 412 #else 413 esdhc_write32(®s->xfertyp, xfertyp); 414 #endif 415 416 /* Wait for the command to complete */ 417 while (!(esdhc_read32(®s->irqstat) & (IRQSTAT_CC | IRQSTAT_CTOE))) 418 ; 419 420 irqstat = esdhc_read32(®s->irqstat); 421 422 if (irqstat & CMD_ERR) { 423 err = -ECOMM; 424 goto out; 425 } 426 427 if (irqstat & IRQSTAT_CTOE) { 428 err = -ETIMEDOUT; 429 goto out; 430 } 431 432 /* Switch voltage to 1.8V if CMD11 succeeded */ 433 if (cmd->cmdidx == SD_CMD_SWITCH_UHS18V) { 434 esdhc_setbits32(®s->vendorspec, ESDHC_VENDORSPEC_VSELECT); 435 436 printf("Run CMD11 1.8V switch\n"); 437 /* Sleep for 5 ms - max time for card to switch to 1.8V */ 438 udelay(5000); 439 } 440 441 /* Workaround for ESDHC errata ENGcm03648 */ 442 if (!data && (cmd->resp_type & MMC_RSP_BUSY)) { 443 int timeout = 6000; 444 445 /* Poll on DATA0 line for cmd with busy signal for 600 ms */ 446 while (timeout > 0 && !(esdhc_read32(®s->prsstat) & 447 PRSSTAT_DAT0)) { 448 udelay(100); 449 timeout--; 450 } 451 452 if (timeout <= 0) { 453 printf("Timeout waiting for DAT0 to go high!\n"); 454 err = -ETIMEDOUT; 455 goto out; 456 } 457 } 458 459 /* Copy the response to the response buffer */ 460 if (cmd->resp_type & MMC_RSP_136) { 461 u32 cmdrsp3, cmdrsp2, cmdrsp1, cmdrsp0; 462 463 cmdrsp3 = esdhc_read32(®s->cmdrsp3); 464 cmdrsp2 = esdhc_read32(®s->cmdrsp2); 465 cmdrsp1 = esdhc_read32(®s->cmdrsp1); 466 cmdrsp0 = esdhc_read32(®s->cmdrsp0); 467 cmd->response[0] = (cmdrsp3 << 8) | (cmdrsp2 >> 24); 468 cmd->response[1] = (cmdrsp2 << 8) | (cmdrsp1 >> 24); 469 cmd->response[2] = (cmdrsp1 << 8) | (cmdrsp0 >> 24); 470 cmd->response[3] = (cmdrsp0 << 8); 471 } else 472 cmd->response[0] = esdhc_read32(®s->cmdrsp0); 473 474 /* Wait until all of the blocks are transferred */ 475 if (data) { 476 #ifdef CONFIG_SYS_FSL_ESDHC_USE_PIO 477 esdhc_pio_read_write(priv, data); 478 #else 479 do { 480 irqstat = esdhc_read32(®s->irqstat); 481 482 if (irqstat & IRQSTAT_DTOE) { 483 err = -ETIMEDOUT; 484 goto out; 485 } 486 487 if (irqstat & DATA_ERR) { 488 err = -ECOMM; 489 goto out; 490 } 491 } while ((irqstat & DATA_COMPLETE) != DATA_COMPLETE); 492 493 /* 494 * Need invalidate the dcache here again to avoid any 495 * cache-fill during the DMA operations such as the 496 * speculative pre-fetching etc. 497 */ 498 if (data->flags & MMC_DATA_READ) 499 check_and_invalidate_dcache_range(cmd, data); 500 #endif 501 } 502 503 out: 504 /* Reset CMD and DATA portions on error */ 505 if (err) { 506 esdhc_write32(®s->sysctl, esdhc_read32(®s->sysctl) | 507 SYSCTL_RSTC); 508 while (esdhc_read32(®s->sysctl) & SYSCTL_RSTC) 509 ; 510 511 if (data) { 512 esdhc_write32(®s->sysctl, 513 esdhc_read32(®s->sysctl) | 514 SYSCTL_RSTD); 515 while ((esdhc_read32(®s->sysctl) & SYSCTL_RSTD)) 516 ; 517 } 518 519 /* If this was CMD11, then notify that power cycle is needed */ 520 if (cmd->cmdidx == SD_CMD_SWITCH_UHS18V) 521 printf("CMD11 to switch to 1.8V mode failed, card requires power cycle.\n"); 522 } 523 524 esdhc_write32(®s->irqstat, -1); 525 526 return err; 527 } 528 529 static void set_sysctl(struct fsl_esdhc_priv *priv, struct mmc *mmc, uint clock) 530 { 531 int div = 1; 532 #ifdef ARCH_MXC 533 int pre_div = 1; 534 #else 535 int pre_div = 2; 536 #endif 537 int ddr_pre_div = mmc->ddr_mode ? 2 : 1; 538 struct fsl_esdhc *regs = priv->esdhc_regs; 539 int sdhc_clk = priv->sdhc_clk; 540 uint clk; 541 542 if (clock < mmc->cfg->f_min) 543 clock = mmc->cfg->f_min; 544 545 while (sdhc_clk / (16 * pre_div * ddr_pre_div) > clock && pre_div < 256) 546 pre_div *= 2; 547 548 while (sdhc_clk / (div * pre_div * ddr_pre_div) > clock && div < 16) 549 div++; 550 551 pre_div >>= 1; 552 div -= 1; 553 554 clk = (pre_div << 8) | (div << 4); 555 556 #ifdef CONFIG_FSL_USDHC 557 esdhc_clrbits32(®s->vendorspec, VENDORSPEC_CKEN); 558 #else 559 esdhc_clrbits32(®s->sysctl, SYSCTL_CKEN); 560 #endif 561 562 esdhc_clrsetbits32(®s->sysctl, SYSCTL_CLOCK_MASK, clk); 563 564 udelay(10000); 565 566 #ifdef CONFIG_FSL_USDHC 567 esdhc_setbits32(®s->vendorspec, VENDORSPEC_PEREN | VENDORSPEC_CKEN); 568 #else 569 esdhc_setbits32(®s->sysctl, SYSCTL_PEREN | SYSCTL_CKEN); 570 #endif 571 572 } 573 574 #ifdef CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK 575 static void esdhc_clock_control(struct fsl_esdhc_priv *priv, bool enable) 576 { 577 struct fsl_esdhc *regs = priv->esdhc_regs; 578 u32 value; 579 u32 time_out; 580 581 value = esdhc_read32(®s->sysctl); 582 583 if (enable) 584 value |= SYSCTL_CKEN; 585 else 586 value &= ~SYSCTL_CKEN; 587 588 esdhc_write32(®s->sysctl, value); 589 590 time_out = 20; 591 value = PRSSTAT_SDSTB; 592 while (!(esdhc_read32(®s->prsstat) & value)) { 593 if (time_out == 0) { 594 printf("fsl_esdhc: Internal clock never stabilised.\n"); 595 break; 596 } 597 time_out--; 598 mdelay(1); 599 } 600 } 601 #endif 602 603 static int esdhc_set_ios_common(struct fsl_esdhc_priv *priv, struct mmc *mmc) 604 { 605 struct fsl_esdhc *regs = priv->esdhc_regs; 606 607 #ifdef CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK 608 /* Select to use peripheral clock */ 609 esdhc_clock_control(priv, false); 610 esdhc_setbits32(®s->scr, ESDHCCTL_PCS); 611 esdhc_clock_control(priv, true); 612 #endif 613 /* Set the clock speed */ 614 set_sysctl(priv, mmc, mmc->clock); 615 616 /* Set the bus width */ 617 esdhc_clrbits32(®s->proctl, PROCTL_DTW_4 | PROCTL_DTW_8); 618 619 if (mmc->bus_width == 4) 620 esdhc_setbits32(®s->proctl, PROCTL_DTW_4); 621 else if (mmc->bus_width == 8) 622 esdhc_setbits32(®s->proctl, PROCTL_DTW_8); 623 624 return 0; 625 } 626 627 static int esdhc_init_common(struct fsl_esdhc_priv *priv, struct mmc *mmc) 628 { 629 struct fsl_esdhc *regs = priv->esdhc_regs; 630 ulong start; 631 632 /* Reset the entire host controller */ 633 esdhc_setbits32(®s->sysctl, SYSCTL_RSTA); 634 635 /* Wait until the controller is available */ 636 start = get_timer(0); 637 while ((esdhc_read32(®s->sysctl) & SYSCTL_RSTA)) { 638 if (get_timer(start) > 1000) 639 return -ETIMEDOUT; 640 } 641 642 #if defined(CONFIG_FSL_USDHC) 643 /* RSTA doesn't reset MMC_BOOT register, so manually reset it */ 644 esdhc_write32(®s->mmcboot, 0x0); 645 /* Reset MIX_CTRL and CLK_TUNE_CTRL_STATUS regs to 0 */ 646 esdhc_write32(®s->mixctrl, 0x0); 647 esdhc_write32(®s->clktunectrlstatus, 0x0); 648 649 /* Put VEND_SPEC to default value */ 650 esdhc_write32(®s->vendorspec, VENDORSPEC_INIT); 651 652 /* Disable DLL_CTRL delay line */ 653 esdhc_write32(®s->dllctrl, 0x0); 654 #endif 655 656 #ifndef ARCH_MXC 657 /* Enable cache snooping */ 658 esdhc_write32(®s->scr, 0x00000040); 659 #endif 660 661 #ifndef CONFIG_FSL_USDHC 662 esdhc_setbits32(®s->sysctl, SYSCTL_HCKEN | SYSCTL_IPGEN); 663 #else 664 esdhc_setbits32(®s->vendorspec, VENDORSPEC_HCKEN | VENDORSPEC_IPGEN); 665 #endif 666 667 /* Set the initial clock speed */ 668 mmc_set_clock(mmc, 400000); 669 670 /* Disable the BRR and BWR bits in IRQSTAT */ 671 esdhc_clrbits32(®s->irqstaten, IRQSTATEN_BRR | IRQSTATEN_BWR); 672 673 /* Put the PROCTL reg back to the default */ 674 esdhc_write32(®s->proctl, PROCTL_INIT); 675 676 /* Set timout to the maximum value */ 677 esdhc_clrsetbits32(®s->sysctl, SYSCTL_TIMEOUT_MASK, 14 << 16); 678 679 if (priv->vs18_enable) 680 esdhc_setbits32(®s->vendorspec, ESDHC_VENDORSPEC_VSELECT); 681 682 return 0; 683 } 684 685 static int esdhc_getcd_common(struct fsl_esdhc_priv *priv) 686 { 687 struct fsl_esdhc *regs = priv->esdhc_regs; 688 int timeout = 1000; 689 690 #ifdef CONFIG_ESDHC_DETECT_QUIRK 691 if (CONFIG_ESDHC_DETECT_QUIRK) 692 return 1; 693 #endif 694 695 #if CONFIG_IS_ENABLED(DM_MMC) 696 if (priv->non_removable) 697 return 1; 698 #ifdef CONFIG_DM_GPIO 699 if (dm_gpio_is_valid(&priv->cd_gpio)) 700 return dm_gpio_get_value(&priv->cd_gpio); 701 #endif 702 #endif 703 704 while (!(esdhc_read32(®s->prsstat) & PRSSTAT_CINS) && --timeout) 705 udelay(1000); 706 707 return timeout > 0; 708 } 709 710 static int esdhc_reset(struct fsl_esdhc *regs) 711 { 712 ulong start; 713 714 /* reset the controller */ 715 esdhc_setbits32(®s->sysctl, SYSCTL_RSTA); 716 717 /* hardware clears the bit when it is done */ 718 start = get_timer(0); 719 while ((esdhc_read32(®s->sysctl) & SYSCTL_RSTA)) { 720 if (get_timer(start) > 100) { 721 printf("MMC/SD: Reset never completed.\n"); 722 return -ETIMEDOUT; 723 } 724 } 725 726 return 0; 727 } 728 729 #if !CONFIG_IS_ENABLED(DM_MMC) 730 static int esdhc_getcd(struct mmc *mmc) 731 { 732 struct fsl_esdhc_priv *priv = mmc->priv; 733 734 return esdhc_getcd_common(priv); 735 } 736 737 static int esdhc_init(struct mmc *mmc) 738 { 739 struct fsl_esdhc_priv *priv = mmc->priv; 740 741 return esdhc_init_common(priv, mmc); 742 } 743 744 static int esdhc_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd, 745 struct mmc_data *data) 746 { 747 struct fsl_esdhc_priv *priv = mmc->priv; 748 749 return esdhc_send_cmd_common(priv, mmc, cmd, data); 750 } 751 752 static int esdhc_set_ios(struct mmc *mmc) 753 { 754 struct fsl_esdhc_priv *priv = mmc->priv; 755 756 return esdhc_set_ios_common(priv, mmc); 757 } 758 759 static const struct mmc_ops esdhc_ops = { 760 .getcd = esdhc_getcd, 761 .init = esdhc_init, 762 .send_cmd = esdhc_send_cmd, 763 .set_ios = esdhc_set_ios, 764 }; 765 #endif 766 767 static int fsl_esdhc_init(struct fsl_esdhc_priv *priv, 768 struct fsl_esdhc_plat *plat) 769 { 770 struct mmc_config *cfg; 771 struct fsl_esdhc *regs; 772 u32 caps, voltage_caps; 773 int ret; 774 775 if (!priv) 776 return -EINVAL; 777 778 regs = priv->esdhc_regs; 779 780 /* First reset the eSDHC controller */ 781 ret = esdhc_reset(regs); 782 if (ret) 783 return ret; 784 785 #ifndef CONFIG_FSL_USDHC 786 esdhc_setbits32(®s->sysctl, SYSCTL_PEREN | SYSCTL_HCKEN 787 | SYSCTL_IPGEN | SYSCTL_CKEN); 788 #else 789 esdhc_setbits32(®s->vendorspec, VENDORSPEC_PEREN | 790 VENDORSPEC_HCKEN | VENDORSPEC_IPGEN | VENDORSPEC_CKEN); 791 #endif 792 793 if (priv->vs18_enable) 794 esdhc_setbits32(®s->vendorspec, ESDHC_VENDORSPEC_VSELECT); 795 796 writel(SDHCI_IRQ_EN_BITS, ®s->irqstaten); 797 cfg = &plat->cfg; 798 #ifndef CONFIG_DM_MMC 799 memset(cfg, '\0', sizeof(*cfg)); 800 #endif 801 802 voltage_caps = 0; 803 caps = esdhc_read32(®s->hostcapblt); 804 805 #ifdef CONFIG_SYS_FSL_ERRATUM_ESDHC135 806 caps = caps & ~(ESDHC_HOSTCAPBLT_SRS | 807 ESDHC_HOSTCAPBLT_VS18 | ESDHC_HOSTCAPBLT_VS30); 808 #endif 809 810 /* T4240 host controller capabilities register should have VS33 bit */ 811 #ifdef CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 812 caps = caps | ESDHC_HOSTCAPBLT_VS33; 813 #endif 814 815 if (caps & ESDHC_HOSTCAPBLT_VS18) 816 voltage_caps |= MMC_VDD_165_195; 817 if (caps & ESDHC_HOSTCAPBLT_VS30) 818 voltage_caps |= MMC_VDD_29_30 | MMC_VDD_30_31; 819 if (caps & ESDHC_HOSTCAPBLT_VS33) 820 voltage_caps |= MMC_VDD_32_33 | MMC_VDD_33_34; 821 822 cfg->name = "FSL_SDHC"; 823 #if !CONFIG_IS_ENABLED(DM_MMC) 824 cfg->ops = &esdhc_ops; 825 #endif 826 #ifdef CONFIG_SYS_SD_VOLTAGE 827 cfg->voltages = CONFIG_SYS_SD_VOLTAGE; 828 #else 829 cfg->voltages = MMC_VDD_32_33 | MMC_VDD_33_34; 830 #endif 831 if ((cfg->voltages & voltage_caps) == 0) { 832 printf("voltage not supported by controller\n"); 833 return -1; 834 } 835 836 if (priv->bus_width == 8) 837 cfg->host_caps = MMC_MODE_4BIT | MMC_MODE_8BIT; 838 else if (priv->bus_width == 4) 839 cfg->host_caps = MMC_MODE_4BIT; 840 841 cfg->host_caps = MMC_MODE_4BIT | MMC_MODE_8BIT; 842 #ifdef CONFIG_SYS_FSL_ESDHC_HAS_DDR_MODE 843 cfg->host_caps |= MMC_MODE_DDR_52MHz; 844 #endif 845 846 if (priv->bus_width > 0) { 847 if (priv->bus_width < 8) 848 cfg->host_caps &= ~MMC_MODE_8BIT; 849 if (priv->bus_width < 4) 850 cfg->host_caps &= ~MMC_MODE_4BIT; 851 } 852 853 if (caps & ESDHC_HOSTCAPBLT_HSS) 854 cfg->host_caps |= MMC_MODE_HS_52MHz | MMC_MODE_HS; 855 856 #ifdef CONFIG_ESDHC_DETECT_8_BIT_QUIRK 857 if (CONFIG_ESDHC_DETECT_8_BIT_QUIRK) 858 cfg->host_caps &= ~MMC_MODE_8BIT; 859 #endif 860 861 cfg->f_min = 400000; 862 cfg->f_max = min(priv->sdhc_clk, (u32)52000000); 863 864 cfg->b_max = CONFIG_SYS_MMC_MAX_BLK_COUNT; 865 866 return 0; 867 } 868 869 #if !CONFIG_IS_ENABLED(DM_MMC) 870 static int fsl_esdhc_cfg_to_priv(struct fsl_esdhc_cfg *cfg, 871 struct fsl_esdhc_priv *priv) 872 { 873 if (!cfg || !priv) 874 return -EINVAL; 875 876 priv->esdhc_regs = (struct fsl_esdhc *)(unsigned long)(cfg->esdhc_base); 877 priv->bus_width = cfg->max_bus_width; 878 priv->sdhc_clk = cfg->sdhc_clk; 879 priv->wp_enable = cfg->wp_enable; 880 priv->vs18_enable = cfg->vs18_enable; 881 882 return 0; 883 }; 884 885 int fsl_esdhc_initialize(bd_t *bis, struct fsl_esdhc_cfg *cfg) 886 { 887 struct fsl_esdhc_plat *plat; 888 struct fsl_esdhc_priv *priv; 889 struct mmc *mmc; 890 int ret; 891 892 if (!cfg) 893 return -EINVAL; 894 895 priv = calloc(sizeof(struct fsl_esdhc_priv), 1); 896 if (!priv) 897 return -ENOMEM; 898 plat = calloc(sizeof(struct fsl_esdhc_plat), 1); 899 if (!plat) { 900 free(priv); 901 return -ENOMEM; 902 } 903 904 ret = fsl_esdhc_cfg_to_priv(cfg, priv); 905 if (ret) { 906 debug("%s xlate failure\n", __func__); 907 free(plat); 908 free(priv); 909 return ret; 910 } 911 912 ret = fsl_esdhc_init(priv, plat); 913 if (ret) { 914 debug("%s init failure\n", __func__); 915 free(plat); 916 free(priv); 917 return ret; 918 } 919 920 mmc = mmc_create(&plat->cfg, priv); 921 if (!mmc) 922 return -EIO; 923 924 priv->mmc = mmc; 925 926 return 0; 927 } 928 929 int fsl_esdhc_mmc_init(bd_t *bis) 930 { 931 struct fsl_esdhc_cfg *cfg; 932 933 cfg = calloc(sizeof(struct fsl_esdhc_cfg), 1); 934 cfg->esdhc_base = CONFIG_SYS_FSL_ESDHC_ADDR; 935 cfg->sdhc_clk = gd->arch.sdhc_clk; 936 return fsl_esdhc_initialize(bis, cfg); 937 } 938 #endif 939 940 #ifdef CONFIG_FSL_ESDHC_ADAPTER_IDENT 941 void mmc_adapter_card_type_ident(void) 942 { 943 u8 card_id; 944 u8 value; 945 946 card_id = QIXIS_READ(present) & QIXIS_SDID_MASK; 947 gd->arch.sdhc_adapter = card_id; 948 949 switch (card_id) { 950 case QIXIS_ESDHC_ADAPTER_TYPE_EMMC45: 951 value = QIXIS_READ(brdcfg[5]); 952 value |= (QIXIS_DAT4 | QIXIS_DAT5_6_7); 953 QIXIS_WRITE(brdcfg[5], value); 954 break; 955 case QIXIS_ESDHC_ADAPTER_TYPE_SDMMC_LEGACY: 956 value = QIXIS_READ(pwr_ctl[1]); 957 value |= QIXIS_EVDD_BY_SDHC_VS; 958 QIXIS_WRITE(pwr_ctl[1], value); 959 break; 960 case QIXIS_ESDHC_ADAPTER_TYPE_EMMC44: 961 value = QIXIS_READ(brdcfg[5]); 962 value |= (QIXIS_SDCLKIN | QIXIS_SDCLKOUT); 963 QIXIS_WRITE(brdcfg[5], value); 964 break; 965 case QIXIS_ESDHC_ADAPTER_TYPE_RSV: 966 break; 967 case QIXIS_ESDHC_ADAPTER_TYPE_MMC: 968 break; 969 case QIXIS_ESDHC_ADAPTER_TYPE_SD: 970 break; 971 case QIXIS_ESDHC_NO_ADAPTER: 972 break; 973 default: 974 break; 975 } 976 } 977 #endif 978 979 #ifdef CONFIG_OF_LIBFDT 980 __weak int esdhc_status_fixup(void *blob, const char *compat) 981 { 982 #ifdef CONFIG_FSL_ESDHC_PIN_MUX 983 if (!hwconfig("esdhc")) { 984 do_fixup_by_compat(blob, compat, "status", "disabled", 985 sizeof("disabled"), 1); 986 return 1; 987 } 988 #endif 989 return 0; 990 } 991 992 void fdt_fixup_esdhc(void *blob, bd_t *bd) 993 { 994 const char *compat = "fsl,esdhc"; 995 996 if (esdhc_status_fixup(blob, compat)) 997 return; 998 999 #ifdef CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK 1000 do_fixup_by_compat_u32(blob, compat, "peripheral-frequency", 1001 gd->arch.sdhc_clk, 1); 1002 #else 1003 do_fixup_by_compat_u32(blob, compat, "clock-frequency", 1004 gd->arch.sdhc_clk, 1); 1005 #endif 1006 #ifdef CONFIG_FSL_ESDHC_ADAPTER_IDENT 1007 do_fixup_by_compat_u32(blob, compat, "adapter-type", 1008 (u32)(gd->arch.sdhc_adapter), 1); 1009 #endif 1010 } 1011 #endif 1012 1013 #if CONFIG_IS_ENABLED(DM_MMC) 1014 #include <asm/arch/clock.h> 1015 __weak void init_clk_usdhc(u32 index) 1016 { 1017 } 1018 1019 static int fsl_esdhc_probe(struct udevice *dev) 1020 { 1021 struct mmc_uclass_priv *upriv = dev_get_uclass_priv(dev); 1022 struct fsl_esdhc_plat *plat = dev_get_platdata(dev); 1023 struct fsl_esdhc_priv *priv = dev_get_priv(dev); 1024 #ifdef CONFIG_DM_REGULATOR 1025 struct udevice *vqmmc_dev; 1026 #endif 1027 fdt_addr_t addr; 1028 unsigned int val; 1029 struct mmc *mmc; 1030 int ret; 1031 1032 addr = dev_read_addr(dev); 1033 if (addr == FDT_ADDR_T_NONE) 1034 return -EINVAL; 1035 1036 priv->esdhc_regs = (struct fsl_esdhc *)addr; 1037 priv->dev = dev; 1038 1039 val = dev_read_u32_default(dev, "bus-width", -1); 1040 if (val == 8) 1041 priv->bus_width = 8; 1042 else if (val == 4) 1043 priv->bus_width = 4; 1044 else 1045 priv->bus_width = 1; 1046 1047 if (dev_read_bool(dev, "non-removable")) { 1048 priv->non_removable = 1; 1049 } else { 1050 priv->non_removable = 0; 1051 #ifdef CONFIG_DM_GPIO 1052 gpio_request_by_name(dev, "cd-gpios", 0, &priv->cd_gpio, 1053 GPIOD_IS_IN); 1054 #endif 1055 } 1056 1057 priv->wp_enable = 1; 1058 1059 #ifdef CONFIG_DM_GPIO 1060 ret = gpio_request_by_name(dev, "wp-gpios", 0, &priv->wp_gpio, 1061 GPIOD_IS_IN); 1062 if (ret) 1063 priv->wp_enable = 0; 1064 #endif 1065 1066 priv->vs18_enable = 0; 1067 1068 #ifdef CONFIG_DM_REGULATOR 1069 /* 1070 * If emmc I/O has a fixed voltage at 1.8V, this must be provided, 1071 * otherwise, emmc will work abnormally. 1072 */ 1073 ret = device_get_supply_regulator(dev, "vqmmc-supply", &vqmmc_dev); 1074 if (ret) { 1075 dev_dbg(dev, "no vqmmc-supply\n"); 1076 } else { 1077 ret = regulator_set_enable(vqmmc_dev, true); 1078 if (ret) { 1079 dev_err(dev, "fail to enable vqmmc-supply\n"); 1080 return ret; 1081 } 1082 1083 if (regulator_get_value(vqmmc_dev) == 1800000) 1084 priv->vs18_enable = 1; 1085 } 1086 #endif 1087 1088 /* 1089 * TODO: 1090 * Because lack of clk driver, if SDHC clk is not enabled, 1091 * need to enable it first before this driver is invoked. 1092 * 1093 * we use MXC_ESDHC_CLK to get clk freq. 1094 * If one would like to make this function work, 1095 * the aliases should be provided in dts as this: 1096 * 1097 * aliases { 1098 * mmc0 = &usdhc1; 1099 * mmc1 = &usdhc2; 1100 * mmc2 = &usdhc3; 1101 * mmc3 = &usdhc4; 1102 * }; 1103 * Then if your board only supports mmc2 and mmc3, but we can 1104 * correctly get the seq as 2 and 3, then let mxc_get_clock 1105 * work as expected. 1106 */ 1107 1108 init_clk_usdhc(dev->seq); 1109 1110 priv->sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK + dev->seq); 1111 if (priv->sdhc_clk <= 0) { 1112 dev_err(dev, "Unable to get clk for %s\n", dev->name); 1113 return -EINVAL; 1114 } 1115 1116 ret = fsl_esdhc_init(priv, plat); 1117 if (ret) { 1118 dev_err(dev, "fsl_esdhc_init failure\n"); 1119 return ret; 1120 } 1121 1122 mmc = &plat->mmc; 1123 mmc->cfg = &plat->cfg; 1124 mmc->dev = dev; 1125 upriv->mmc = mmc; 1126 1127 return esdhc_init_common(priv, mmc); 1128 } 1129 1130 #if CONFIG_IS_ENABLED(DM_MMC) 1131 static int fsl_esdhc_get_cd(struct udevice *dev) 1132 { 1133 struct fsl_esdhc_priv *priv = dev_get_priv(dev); 1134 1135 return true; 1136 return esdhc_getcd_common(priv); 1137 } 1138 1139 static int fsl_esdhc_send_cmd(struct udevice *dev, struct mmc_cmd *cmd, 1140 struct mmc_data *data) 1141 { 1142 struct fsl_esdhc_plat *plat = dev_get_platdata(dev); 1143 struct fsl_esdhc_priv *priv = dev_get_priv(dev); 1144 1145 return esdhc_send_cmd_common(priv, &plat->mmc, cmd, data); 1146 } 1147 1148 static int fsl_esdhc_set_ios(struct udevice *dev) 1149 { 1150 struct fsl_esdhc_plat *plat = dev_get_platdata(dev); 1151 struct fsl_esdhc_priv *priv = dev_get_priv(dev); 1152 1153 return esdhc_set_ios_common(priv, &plat->mmc); 1154 } 1155 1156 static const struct dm_mmc_ops fsl_esdhc_ops = { 1157 .get_cd = fsl_esdhc_get_cd, 1158 .send_cmd = fsl_esdhc_send_cmd, 1159 .set_ios = fsl_esdhc_set_ios, 1160 }; 1161 #endif 1162 1163 static const struct udevice_id fsl_esdhc_ids[] = { 1164 { .compatible = "fsl,imx6ul-usdhc", }, 1165 { .compatible = "fsl,imx6sx-usdhc", }, 1166 { .compatible = "fsl,imx6sl-usdhc", }, 1167 { .compatible = "fsl,imx6q-usdhc", }, 1168 { .compatible = "fsl,imx7d-usdhc", }, 1169 { .compatible = "fsl,imx7ulp-usdhc", }, 1170 { .compatible = "fsl,esdhc", }, 1171 { /* sentinel */ } 1172 }; 1173 1174 #if CONFIG_IS_ENABLED(BLK) 1175 static int fsl_esdhc_bind(struct udevice *dev) 1176 { 1177 struct fsl_esdhc_plat *plat = dev_get_platdata(dev); 1178 1179 return mmc_bind(dev, &plat->mmc, &plat->cfg); 1180 } 1181 #endif 1182 1183 U_BOOT_DRIVER(fsl_esdhc) = { 1184 .name = "fsl-esdhc-mmc", 1185 .id = UCLASS_MMC, 1186 .of_match = fsl_esdhc_ids, 1187 .ops = &fsl_esdhc_ops, 1188 #if CONFIG_IS_ENABLED(BLK) 1189 .bind = fsl_esdhc_bind, 1190 #endif 1191 .probe = fsl_esdhc_probe, 1192 .platdata_auto_alloc_size = sizeof(struct fsl_esdhc_plat), 1193 .priv_auto_alloc_size = sizeof(struct fsl_esdhc_priv), 1194 }; 1195 #endif 1196