xref: /openbmc/u-boot/drivers/misc/Kconfig (revision e7ab6dfc) 
1#
2# Multifunction miscellaneous devices
3#
4
5menu "Multifunction device drivers"
6
7config MISC
8	bool "Enable Driver Model for Misc drivers"
9	depends on DM
10	help
11	  Enable driver model for miscellaneous devices. This class is
12	  used only for those do not fit other more general classes. A
13	  set of generic read, write and ioctl methods may be used to
14	  access the device.
15
16config ALTERA_SYSID
17	bool "Altera Sysid support"
18	depends on MISC
19	help
20	  Select this to enable a sysid for Altera devices. Please find
21	  details on the "Embedded Peripherals IP User Guide" of Altera.
22
23config ATSHA204A
24	bool "Support for Atmel ATSHA204A module"
25	depends on MISC
26	help
27	   Enable support for I2C connected Atmel's ATSHA204A
28	   CryptoAuthentication module found for example on the Turris Omnia
29	   board.
30
31config ROCKCHIP_EFUSE
32        bool "Rockchip e-fuse support"
33	depends on MISC
34	help
35	  Enable (read-only) access for the e-fuse block found in Rockchip
36	  SoCs: accesses can either be made using byte addressing and a length
37	  or through child-nodes that are generated based on the e-fuse map
38	  retrieved from the DTS.
39
40	  This driver currently supports the RK3399 only, but can easily be
41	  extended (by porting the read function from the Linux kernel sources)
42	  to support other recent Rockchip devices.
43
44config VEXPRESS_CONFIG
45	bool "Enable support for Arm Versatile Express config bus"
46	depends on MISC
47	help
48	  If you say Y here, you will get support for accessing the
49	  configuration bus on the Arm Versatile Express boards via
50	  a sysreg driver.
51
52config CMD_CROS_EC
53	bool "Enable crosec command"
54	depends on CROS_EC
55	help
56	  Enable command-line access to the Chrome OS EC (Embedded
57	  Controller). This provides the 'crosec' command which has
58	  a number of sub-commands for performing EC tasks such as
59	  updating its flash, accessing a small saved context area
60	  and talking to the I2C bus behind the EC (if there is one).
61
62config CROS_EC
63	bool "Enable Chrome OS EC"
64	help
65	  Enable access to the Chrome OS EC. This is a separate
66	  microcontroller typically available on a SPI bus on Chromebooks. It
67	  provides access to the keyboard, some internal storage and may
68	  control access to the battery and main PMIC depending on the
69	  device. You can use the 'crosec' command to access it.
70
71config CROS_EC_I2C
72	bool "Enable Chrome OS EC I2C driver"
73	depends on CROS_EC
74	help
75	  Enable I2C access to the Chrome OS EC. This is used on older
76	  ARM Chromebooks such as snow and spring before the standard bus
77	  changed to SPI. The EC will accept commands across the I2C using
78	  a special message protocol, and provide responses.
79
80config CROS_EC_LPC
81	bool "Enable Chrome OS EC LPC driver"
82	depends on CROS_EC
83	help
84	  Enable I2C access to the Chrome OS EC. This is used on x86
85	  Chromebooks such as link and falco. The keyboard is provided
86	  through a legacy port interface, so on x86 machines the main
87	  function of the EC is power and thermal management.
88
89config CROS_EC_SANDBOX
90	bool "Enable Chrome OS EC sandbox driver"
91	depends on CROS_EC && SANDBOX
92	help
93	  Enable a sandbox emulation of the Chrome OS EC. This supports
94	  keyboard (use the -l flag to enable the LCD), verified boot context,
95	  EC flash read/write/erase support and a few other things. It is
96	  enough to perform a Chrome OS verified boot on sandbox.
97
98config CROS_EC_SPI
99	bool "Enable Chrome OS EC SPI driver"
100	depends on CROS_EC
101	help
102	  Enable SPI access to the Chrome OS EC. This is used on newer
103	  ARM Chromebooks such as pit, pi and nyan-big. The SPI interface
104	  provides a faster and more robust interface than I2C but the bugs
105	  are less interesting.
106
107config DS4510
108	bool "Enable support for DS4510 CPU supervisor"
109	help
110	  Enable support for the Maxim DS4510 CPU supervisor. It has an
111	  integrated 64-byte EEPROM, four programmable non-volatile I/O pins
112	  and a configurable timer for the supervisor function. The device is
113	  connected over I2C.
114
115config FSL_SEC_MON
116	bool "Enable FSL SEC_MON Driver"
117	help
118	  Freescale Security Monitor block is responsible for monitoring
119	  system states.
120	  Security Monitor can be transitioned on any security failures,
121	  like software violations or hardware security violations.
122
123config JZ4780_EFUSE
124	bool "Ingenic JZ4780 eFUSE support"
125	depends on ARCH_JZ47XX
126	help
127	  This selects support for the eFUSE on Ingenic JZ4780 SoCs.
128
129config MXC_OCOTP
130	bool "Enable MXC OCOTP Driver"
131	help
132	  If you say Y here, you will get support for the One Time
133	  Programmable memory pages that are stored on the some
134	  Freescale i.MX processors.
135
136config NUVOTON_NCT6102D
137	bool "Enable Nuvoton NCT6102D Super I/O driver"
138	help
139	  If you say Y here, you will get support for the Nuvoton
140	  NCT6102D Super I/O driver. This can be used to enable or
141	  disable the legacy UART, the watchdog or other devices
142	  in the Nuvoton Super IO chips on X86 platforms.
143
144config PWRSEQ
145	bool "Enable power-sequencing drivers"
146	depends on DM
147	help
148	  Power-sequencing drivers provide support for controlling power for
149	  devices. They are typically referenced by a phandle from another
150	  device. When the device is started up, its power sequence can be
151	  initiated.
152
153config SPL_PWRSEQ
154	bool "Enable power-sequencing drivers for SPL"
155	depends on PWRSEQ
156	help
157	  Power-sequencing drivers provide support for controlling power for
158	  devices. They are typically referenced by a phandle from another
159	  device. When the device is started up, its power sequence can be
160	  initiated.
161
162config PCA9551_LED
163	bool "Enable PCA9551 LED driver"
164	help
165	  Enable driver for PCA9551 LED controller. This controller
166	  is connected via I2C. So I2C needs to be enabled.
167
168config PCA9551_I2C_ADDR
169	hex "I2C address of PCA9551 LED controller"
170	depends on PCA9551_LED
171	default 0x60
172	help
173	  The I2C address of the PCA9551 LED controller.
174
175config STM32MP_FUSE
176	bool "Enable STM32MP fuse wrapper providing the fuse API"
177	depends on ARCH_STM32MP && MISC
178	default y if CMD_FUSE
179	help
180	  If you say Y here, you will get support for the fuse API (OTP)
181	  for STM32MP architecture.
182	  This API is needed for CMD_FUSE.
183
184config STM32_RCC
185	bool "Enable RCC driver for the STM32 SoC's family"
186	depends on (STM32 || ARCH_STM32MP) && MISC
187	help
188	  Enable the STM32 RCC driver. The RCC block (Reset and Clock Control
189	  block) is responsible of the management of the clock and reset
190	  generation.
191	  This driver is similar to an MFD driver in the Linux kernel.
192
193config TEGRA_CAR
194	bool "Enable support for the Tegra CAR driver"
195	depends on TEGRA_NO_BPMP
196	help
197	  The Tegra CAR (Clock and Reset Controller) is a HW module that
198	  controls almost all clocks and resets in a Tegra SoC.
199
200config TEGRA186_BPMP
201	bool "Enable support for the Tegra186 BPMP driver"
202	depends on TEGRA186
203	help
204	  The Tegra BPMP (Boot and Power Management Processor) is a separate
205	  auxiliary CPU embedded into Tegra to perform power management work,
206	  and controls related features such as clocks, resets, power domains,
207	  PMIC I2C bus, etc. This driver provides the core low-level
208	  communication path by which feature-specific drivers (such as clock)
209	  can make requests to the BPMP. This driver is similar to an MFD
210	  driver in the Linux kernel.
211
212config TWL4030_LED
213	bool "Enable TWL4030 LED controller"
214	help
215	  Enable this to add support for the TWL4030 LED controller.
216
217config WINBOND_W83627
218	bool "Enable Winbond Super I/O driver"
219	help
220	  If you say Y here, you will get support for the Winbond
221	  W83627 Super I/O driver. This can be used to enable the
222	  legacy UART or other devices in the Winbond Super IO chips
223	  on X86 platforms.
224
225config QFW
226	bool
227	help
228	  Hidden option to enable QEMU fw_cfg interface. This will be selected by
229	  either CONFIG_CMD_QFW or CONFIG_GENERATE_ACPI_TABLE.
230
231config I2C_EEPROM
232	bool "Enable driver for generic I2C-attached EEPROMs"
233	depends on MISC
234	help
235	  Enable a generic driver for EEPROMs attached via I2C.
236
237
238config SPL_I2C_EEPROM
239	bool "Enable driver for generic I2C-attached EEPROMs for SPL"
240	depends on MISC && SPL && SPL_DM
241	help
242	  This option is an SPL-variant of the I2C_EEPROM option.
243	  See the help of I2C_EEPROM for details.
244
245config ZYNQ_GEM_I2C_MAC_OFFSET
246	hex "Set the I2C MAC offset"
247	default 0x0
248	help
249	  Set the MAC offset for i2C.
250
251if I2C_EEPROM
252
253config SYS_I2C_EEPROM_ADDR
254	hex "Chip address of the EEPROM device"
255	default 0
256
257config SYS_I2C_EEPROM_BUS
258	int "I2C bus of the EEPROM device."
259	default 0
260
261config SYS_EEPROM_SIZE
262	int "Size in bytes of the EEPROM device"
263	default 256
264
265config SYS_EEPROM_PAGE_WRITE_BITS
266	int "Number of bits used to address bytes in a single page"
267	default 0
268	help
269	  The EEPROM page size is 2^SYS_EEPROM_PAGE_WRITE_BITS.
270	  A 64 byte page, for example would require six bits.
271
272config SYS_EEPROM_PAGE_WRITE_DELAY_MS
273	int "Number of milliseconds to delay between page writes"
274	default 0
275
276config SYS_I2C_EEPROM_ADDR_LEN
277	int "Length in bytes of the EEPROM memory array address"
278	default 1
279	help
280	  Note: This is NOT the chip address length!
281
282config SYS_I2C_EEPROM_ADDR_OVERFLOW
283	hex "EEPROM Address Overflow"
284	default 0
285	help
286	  EEPROM chips that implement "address overflow" are ones
287	  like Catalyst 24WC04/08/16 which has 9/10/11 bits of
288	  address and the extra bits end up in the "chip address" bit
289	  slots. This makes a 24WC08 (1Kbyte) chip look like four 256
290	  byte chips.
291
292endif
293
294config GDSYS_RXAUI_CTRL
295	bool "Enable gdsys RXAUI control driver"
296	depends on MISC
297	help
298	  Support gdsys FPGA's RXAUI control.
299
300config GDSYS_IOEP
301	bool "Enable gdsys IOEP driver"
302	depends on MISC
303	help
304	  Support gdsys FPGA's IO endpoint driver.
305
306config MPC83XX_SERDES
307	bool "Enable MPC83xx serdes driver"
308	depends on MISC
309	help
310	  Support for serdes found on MPC83xx SoCs.
311
312config FS_LOADER
313	bool "Enable loader driver for file system"
314	help
315	  This is file system generic loader which can be used to load
316	  the file image from the storage into target such as memory.
317
318	  The consumer driver would then use this loader to program whatever,
319	  ie. the FPGA device.
320
321config GDSYS_SOC
322	bool "Enable gdsys SOC driver"
323	depends on MISC
324	help
325	  Support for gdsys IHS SOC, a simple bus associated with each gdsys
326	  IHS (Integrated Hardware Systems) FPGA, which holds all devices whose
327	  register maps are contained within the FPGA's register map.
328
329config IHS_FPGA
330	bool "Enable IHS FPGA driver"
331	depends on MISC
332	help
333	  Support IHS (Integrated Hardware Systems) FPGA, the main FPGAs on
334	  gdsys devices, which supply the majority of the functionality offered
335	  by the devices. This driver supports both CON and CPU variants of the
336	  devices, depending on the device tree entry.
337
338endmenu
339