1 /* 2 * Copyright (c) 2012 The Chromium OS Authors. All rights reserved. 3 * Copyright (c) 2010-2011 NVIDIA Corporation 4 * NVIDIA Corporation <www.nvidia.com> 5 * 6 * SPDX-License-Identifier: GPL-2.0+ 7 */ 8 9 #include <common.h> 10 #include <dm.h> 11 #include <errno.h> 12 #include <fdtdec.h> 13 #include <i2c.h> 14 #include <asm/io.h> 15 #include <clk.h> 16 #include <reset.h> 17 #ifndef CONFIG_TEGRA186 18 #include <asm/arch/clock.h> 19 #include <asm/arch/funcmux.h> 20 #endif 21 #include <asm/arch/gpio.h> 22 #include <asm/arch-tegra/tegra_i2c.h> 23 24 DECLARE_GLOBAL_DATA_PTR; 25 26 enum i2c_type { 27 TYPE_114, 28 TYPE_STD, 29 TYPE_DVC, 30 }; 31 32 /* Information about i2c controller */ 33 struct i2c_bus { 34 int id; 35 struct reset_ctl reset_ctl; 36 struct clk clk; 37 int speed; 38 int pinmux_config; 39 struct i2c_control *control; 40 struct i2c_ctlr *regs; 41 enum i2c_type type; 42 int inited; /* bus is inited */ 43 }; 44 45 static void set_packet_mode(struct i2c_bus *i2c_bus) 46 { 47 u32 config; 48 49 config = I2C_CNFG_NEW_MASTER_FSM_MASK | I2C_CNFG_PACKET_MODE_MASK; 50 51 if (i2c_bus->type == TYPE_DVC) { 52 struct dvc_ctlr *dvc = (struct dvc_ctlr *)i2c_bus->regs; 53 54 writel(config, &dvc->cnfg); 55 } else { 56 writel(config, &i2c_bus->regs->cnfg); 57 /* 58 * program I2C_SL_CNFG.NEWSL to ENABLE. This fixes probe 59 * issues, i.e., some slaves may be wrongly detected. 60 */ 61 setbits_le32(&i2c_bus->regs->sl_cnfg, I2C_SL_CNFG_NEWSL_MASK); 62 } 63 } 64 65 static void i2c_reset_controller(struct i2c_bus *i2c_bus) 66 { 67 /* Reset I2C controller. */ 68 reset_assert(&i2c_bus->reset_ctl); 69 udelay(1); 70 reset_deassert(&i2c_bus->reset_ctl); 71 udelay(1); 72 73 /* re-program config register to packet mode */ 74 set_packet_mode(i2c_bus); 75 } 76 77 static int i2c_init_clock(struct i2c_bus *i2c_bus, unsigned rate) 78 { 79 int ret; 80 81 ret = reset_assert(&i2c_bus->reset_ctl); 82 if (ret) 83 return ret; 84 ret = clk_enable(&i2c_bus->clk); 85 if (ret) 86 return ret; 87 ret = clk_set_rate(&i2c_bus->clk, rate); 88 if (IS_ERR_VALUE(ret)) 89 return ret; 90 ret = reset_deassert(&i2c_bus->reset_ctl); 91 if (ret) 92 return ret; 93 94 return 0; 95 } 96 97 static void i2c_init_controller(struct i2c_bus *i2c_bus) 98 { 99 if (!i2c_bus->speed) 100 return; 101 debug("%s: speed=%d\n", __func__, i2c_bus->speed); 102 /* 103 * Use PLLP - DP-04508-001_v06 datasheet indicates a divisor of 8 104 * here, in section 23.3.1, but in fact we seem to need a factor of 105 * 16 to get the right frequency. 106 */ 107 i2c_init_clock(i2c_bus, i2c_bus->speed * 2 * 8); 108 109 if (i2c_bus->type == TYPE_114) { 110 /* 111 * T114 I2C went to a single clock source for standard/fast and 112 * HS clock speeds. The new clock rate setting calculation is: 113 * SCL = CLK_SOURCE.I2C / 114 * (CLK_MULT_STD_FAST_MODE * (I2C_CLK_DIV_STD_FAST_MODE+1) * 115 * I2C FREQUENCY DIVISOR) as per the T114 TRM (sec 30.3.1). 116 * 117 * NOTE: We do this here, after the initial clock/pll start, 118 * because if we read the clk_div reg before the controller 119 * is running, we hang, and we need it for the new calc. 120 */ 121 int clk_div_stdfst_mode = readl(&i2c_bus->regs->clk_div) >> 16; 122 unsigned rate = CLK_MULT_STD_FAST_MODE * 123 (clk_div_stdfst_mode + 1) * i2c_bus->speed * 2; 124 debug("%s: CLK_DIV_STD_FAST_MODE setting = %d\n", __func__, 125 clk_div_stdfst_mode); 126 127 i2c_init_clock(i2c_bus, rate); 128 } 129 130 /* Reset I2C controller. */ 131 i2c_reset_controller(i2c_bus); 132 133 /* Configure I2C controller. */ 134 if (i2c_bus->type == TYPE_DVC) { /* only for DVC I2C */ 135 struct dvc_ctlr *dvc = (struct dvc_ctlr *)i2c_bus->regs; 136 137 setbits_le32(&dvc->ctrl3, DVC_CTRL_REG3_I2C_HW_SW_PROG_MASK); 138 } 139 140 #ifndef CONFIG_TEGRA186 141 funcmux_select(i2c_bus->clk.id, i2c_bus->pinmux_config); 142 #endif 143 } 144 145 static void send_packet_headers( 146 struct i2c_bus *i2c_bus, 147 struct i2c_trans_info *trans, 148 u32 packet_id, 149 bool end_with_repeated_start) 150 { 151 u32 data; 152 153 /* prepare header1: Header size = 0 Protocol = I2C, pktType = 0 */ 154 data = PROTOCOL_TYPE_I2C << PKT_HDR1_PROTOCOL_SHIFT; 155 data |= packet_id << PKT_HDR1_PKT_ID_SHIFT; 156 data |= i2c_bus->id << PKT_HDR1_CTLR_ID_SHIFT; 157 writel(data, &i2c_bus->control->tx_fifo); 158 debug("pkt header 1 sent (0x%x)\n", data); 159 160 /* prepare header2 */ 161 data = (trans->num_bytes - 1) << PKT_HDR2_PAYLOAD_SIZE_SHIFT; 162 writel(data, &i2c_bus->control->tx_fifo); 163 debug("pkt header 2 sent (0x%x)\n", data); 164 165 /* prepare IO specific header: configure the slave address */ 166 data = trans->address << PKT_HDR3_SLAVE_ADDR_SHIFT; 167 168 /* Enable Read if it is not a write transaction */ 169 if (!(trans->flags & I2C_IS_WRITE)) 170 data |= PKT_HDR3_READ_MODE_MASK; 171 if (end_with_repeated_start) 172 data |= PKT_HDR3_REPEAT_START_MASK; 173 174 /* Write I2C specific header */ 175 writel(data, &i2c_bus->control->tx_fifo); 176 debug("pkt header 3 sent (0x%x)\n", data); 177 } 178 179 static int wait_for_tx_fifo_empty(struct i2c_control *control) 180 { 181 u32 count; 182 int timeout_us = I2C_TIMEOUT_USEC; 183 184 while (timeout_us >= 0) { 185 count = (readl(&control->fifo_status) & TX_FIFO_EMPTY_CNT_MASK) 186 >> TX_FIFO_EMPTY_CNT_SHIFT; 187 if (count == I2C_FIFO_DEPTH) 188 return 1; 189 udelay(10); 190 timeout_us -= 10; 191 } 192 193 return 0; 194 } 195 196 static int wait_for_rx_fifo_notempty(struct i2c_control *control) 197 { 198 u32 count; 199 int timeout_us = I2C_TIMEOUT_USEC; 200 201 while (timeout_us >= 0) { 202 count = (readl(&control->fifo_status) & TX_FIFO_FULL_CNT_MASK) 203 >> TX_FIFO_FULL_CNT_SHIFT; 204 if (count) 205 return 1; 206 udelay(10); 207 timeout_us -= 10; 208 } 209 210 return 0; 211 } 212 213 static int wait_for_transfer_complete(struct i2c_control *control) 214 { 215 int int_status; 216 int timeout_us = I2C_TIMEOUT_USEC; 217 218 while (timeout_us >= 0) { 219 int_status = readl(&control->int_status); 220 if (int_status & I2C_INT_NO_ACK_MASK) 221 return -int_status; 222 if (int_status & I2C_INT_ARBITRATION_LOST_MASK) 223 return -int_status; 224 if (int_status & I2C_INT_XFER_COMPLETE_MASK) 225 return 0; 226 227 udelay(10); 228 timeout_us -= 10; 229 } 230 231 return -1; 232 } 233 234 static int send_recv_packets(struct i2c_bus *i2c_bus, 235 struct i2c_trans_info *trans) 236 { 237 struct i2c_control *control = i2c_bus->control; 238 u32 int_status; 239 u32 words; 240 u8 *dptr; 241 u32 local; 242 uchar last_bytes; 243 int error = 0; 244 int is_write = trans->flags & I2C_IS_WRITE; 245 246 /* clear status from previous transaction, XFER_COMPLETE, NOACK, etc. */ 247 int_status = readl(&control->int_status); 248 writel(int_status, &control->int_status); 249 250 send_packet_headers(i2c_bus, trans, 1, 251 trans->flags & I2C_USE_REPEATED_START); 252 253 words = DIV_ROUND_UP(trans->num_bytes, 4); 254 last_bytes = trans->num_bytes & 3; 255 dptr = trans->buf; 256 257 while (words) { 258 u32 *wptr = (u32 *)dptr; 259 260 if (is_write) { 261 /* deal with word alignment */ 262 if ((words == 1) && last_bytes) { 263 local = 0; 264 memcpy(&local, dptr, last_bytes); 265 } else if ((unsigned long)dptr & 3) { 266 memcpy(&local, dptr, sizeof(u32)); 267 } else { 268 local = *wptr; 269 } 270 writel(local, &control->tx_fifo); 271 debug("pkt data sent (0x%x)\n", local); 272 if (!wait_for_tx_fifo_empty(control)) { 273 error = -1; 274 goto exit; 275 } 276 } else { 277 if (!wait_for_rx_fifo_notempty(control)) { 278 error = -1; 279 goto exit; 280 } 281 /* 282 * for the last word, we read into our local buffer, 283 * in case that caller did not provide enough buffer. 284 */ 285 local = readl(&control->rx_fifo); 286 if ((words == 1) && last_bytes) 287 memcpy(dptr, (char *)&local, last_bytes); 288 else if ((unsigned long)dptr & 3) 289 memcpy(dptr, &local, sizeof(u32)); 290 else 291 *wptr = local; 292 debug("pkt data received (0x%x)\n", local); 293 } 294 words--; 295 dptr += sizeof(u32); 296 } 297 298 if (wait_for_transfer_complete(control)) { 299 error = -1; 300 goto exit; 301 } 302 return 0; 303 exit: 304 /* error, reset the controller. */ 305 i2c_reset_controller(i2c_bus); 306 307 return error; 308 } 309 310 static int tegra_i2c_write_data(struct i2c_bus *i2c_bus, u32 addr, u8 *data, 311 u32 len, bool end_with_repeated_start) 312 { 313 int error; 314 struct i2c_trans_info trans_info; 315 316 trans_info.address = addr; 317 trans_info.buf = data; 318 trans_info.flags = I2C_IS_WRITE; 319 if (end_with_repeated_start) 320 trans_info.flags |= I2C_USE_REPEATED_START; 321 trans_info.num_bytes = len; 322 trans_info.is_10bit_address = 0; 323 324 error = send_recv_packets(i2c_bus, &trans_info); 325 if (error) 326 debug("tegra_i2c_write_data: Error (%d) !!!\n", error); 327 328 return error; 329 } 330 331 static int tegra_i2c_read_data(struct i2c_bus *i2c_bus, u32 addr, u8 *data, 332 u32 len) 333 { 334 int error; 335 struct i2c_trans_info trans_info; 336 337 trans_info.address = addr | 1; 338 trans_info.buf = data; 339 trans_info.flags = 0; 340 trans_info.num_bytes = len; 341 trans_info.is_10bit_address = 0; 342 343 error = send_recv_packets(i2c_bus, &trans_info); 344 if (error) 345 debug("tegra_i2c_read_data: Error (%d) !!!\n", error); 346 347 return error; 348 } 349 350 static int tegra_i2c_set_bus_speed(struct udevice *dev, unsigned int speed) 351 { 352 struct i2c_bus *i2c_bus = dev_get_priv(dev); 353 354 i2c_bus->speed = speed; 355 i2c_init_controller(i2c_bus); 356 357 return 0; 358 } 359 360 static int tegra_i2c_probe(struct udevice *dev) 361 { 362 struct i2c_bus *i2c_bus = dev_get_priv(dev); 363 int ret; 364 bool is_dvc; 365 366 i2c_bus->id = dev->seq; 367 i2c_bus->type = dev_get_driver_data(dev); 368 i2c_bus->regs = (struct i2c_ctlr *)dev_get_addr(dev); 369 370 ret = reset_get_by_name(dev, "i2c", &i2c_bus->reset_ctl); 371 if (ret) { 372 error("reset_get_by_name() failed: %d\n", ret); 373 return ret; 374 } 375 ret = clk_get_by_name(dev, "div-clk", &i2c_bus->clk); 376 if (ret) { 377 error("clk_get_by_name() failed: %d\n", ret); 378 return ret; 379 } 380 381 #ifndef CONFIG_TEGRA186 382 /* 383 * We don't have a binding for pinmux yet. Leave it out for now. So 384 * far no one needs anything other than the default. 385 */ 386 i2c_bus->pinmux_config = FUNCMUX_DEFAULT; 387 388 /* 389 * We can't specify the pinmux config in the fdt, so I2C2 will not 390 * work on Seaboard. It normally has no devices on it anyway. 391 * You could add in this little hack if you need to use it. 392 * The correct solution is a pinmux binding in the fdt. 393 * 394 * if (i2c_bus->clk.id == PERIPH_ID_I2C2) 395 * i2c_bus->pinmux_config = FUNCMUX_I2C2_PTA; 396 */ 397 #endif 398 399 is_dvc = dev_get_driver_data(dev) == TYPE_DVC; 400 if (is_dvc) { 401 i2c_bus->control = 402 &((struct dvc_ctlr *)i2c_bus->regs)->control; 403 } else { 404 i2c_bus->control = &i2c_bus->regs->control; 405 } 406 i2c_init_controller(i2c_bus); 407 debug("%s: controller bus %d at %p, speed %d: ", 408 is_dvc ? "dvc" : "i2c", dev->seq, i2c_bus->regs, i2c_bus->speed); 409 410 return 0; 411 } 412 413 /* i2c write version without the register address */ 414 static int i2c_write_data(struct i2c_bus *i2c_bus, uchar chip, uchar *buffer, 415 int len, bool end_with_repeated_start) 416 { 417 int rc; 418 419 debug("i2c_write_data: chip=0x%x, len=0x%x\n", chip, len); 420 debug("write_data: "); 421 /* use rc for counter */ 422 for (rc = 0; rc < len; ++rc) 423 debug(" 0x%02x", buffer[rc]); 424 debug("\n"); 425 426 /* Shift 7-bit address over for lower-level i2c functions */ 427 rc = tegra_i2c_write_data(i2c_bus, chip << 1, buffer, len, 428 end_with_repeated_start); 429 if (rc) 430 debug("i2c_write_data(): rc=%d\n", rc); 431 432 return rc; 433 } 434 435 /* i2c read version without the register address */ 436 static int i2c_read_data(struct i2c_bus *i2c_bus, uchar chip, uchar *buffer, 437 int len) 438 { 439 int rc; 440 441 debug("inside i2c_read_data():\n"); 442 /* Shift 7-bit address over for lower-level i2c functions */ 443 rc = tegra_i2c_read_data(i2c_bus, chip << 1, buffer, len); 444 if (rc) { 445 debug("i2c_read_data(): rc=%d\n", rc); 446 return rc; 447 } 448 449 debug("i2c_read_data: "); 450 /* reuse rc for counter*/ 451 for (rc = 0; rc < len; ++rc) 452 debug(" 0x%02x", buffer[rc]); 453 debug("\n"); 454 455 return 0; 456 } 457 458 /* Probe to see if a chip is present. */ 459 static int tegra_i2c_probe_chip(struct udevice *bus, uint chip_addr, 460 uint chip_flags) 461 { 462 struct i2c_bus *i2c_bus = dev_get_priv(bus); 463 int rc; 464 u8 reg; 465 466 /* Shift 7-bit address over for lower-level i2c functions */ 467 rc = tegra_i2c_write_data(i2c_bus, chip_addr << 1, ®, sizeof(reg), 468 false); 469 470 return rc; 471 } 472 473 static int tegra_i2c_xfer(struct udevice *bus, struct i2c_msg *msg, 474 int nmsgs) 475 { 476 struct i2c_bus *i2c_bus = dev_get_priv(bus); 477 int ret; 478 479 debug("i2c_xfer: %d messages\n", nmsgs); 480 for (; nmsgs > 0; nmsgs--, msg++) { 481 bool next_is_read = nmsgs > 1 && (msg[1].flags & I2C_M_RD); 482 483 debug("i2c_xfer: chip=0x%x, len=0x%x\n", msg->addr, msg->len); 484 if (msg->flags & I2C_M_RD) { 485 ret = i2c_read_data(i2c_bus, msg->addr, msg->buf, 486 msg->len); 487 } else { 488 ret = i2c_write_data(i2c_bus, msg->addr, msg->buf, 489 msg->len, next_is_read); 490 } 491 if (ret) { 492 debug("i2c_write: error sending\n"); 493 return -EREMOTEIO; 494 } 495 } 496 497 return 0; 498 } 499 500 int tegra_i2c_get_dvc_bus(struct udevice **busp) 501 { 502 struct udevice *bus; 503 504 for (uclass_first_device(UCLASS_I2C, &bus); 505 bus; 506 uclass_next_device(&bus)) { 507 if (dev_get_driver_data(bus) == TYPE_DVC) { 508 *busp = bus; 509 return 0; 510 } 511 } 512 513 return -ENODEV; 514 } 515 516 static const struct dm_i2c_ops tegra_i2c_ops = { 517 .xfer = tegra_i2c_xfer, 518 .probe_chip = tegra_i2c_probe_chip, 519 .set_bus_speed = tegra_i2c_set_bus_speed, 520 }; 521 522 static const struct udevice_id tegra_i2c_ids[] = { 523 { .compatible = "nvidia,tegra114-i2c", .data = TYPE_114 }, 524 { .compatible = "nvidia,tegra20-i2c", .data = TYPE_STD }, 525 { .compatible = "nvidia,tegra20-i2c-dvc", .data = TYPE_DVC }, 526 { } 527 }; 528 529 U_BOOT_DRIVER(i2c_tegra) = { 530 .name = "i2c_tegra", 531 .id = UCLASS_I2C, 532 .of_match = tegra_i2c_ids, 533 .probe = tegra_i2c_probe, 534 .priv_auto_alloc_size = sizeof(struct i2c_bus), 535 .ops = &tegra_i2c_ops, 536 }; 537