1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * (C) Copyright 2009 4 * Heiko Schocher, DENX Software Engineering, hs@denx.de. 5 * Changes for multibus/multiadapter I2C support. 6 * 7 * (C) Copyright 2001, 2002 8 * Wolfgang Denk, DENX Software Engineering, wd@denx.de. 9 * 10 * This has been changed substantially by Gerald Van Baren, Custom IDEAS, 11 * vanbaren@cideas.com. It was heavily influenced by LiMon, written by 12 * Neil Russell. 13 * 14 * NOTE: This driver should be converted to driver model before June 2017. 15 * Please see doc/driver-model/i2c-howto.txt for instructions. 16 */ 17 18 #include <common.h> 19 #if defined(CONFIG_AT91FAMILY) 20 #include <asm/io.h> 21 #include <asm/arch/hardware.h> 22 #include <asm/arch/at91_pio.h> 23 #ifdef CONFIG_ATMEL_LEGACY 24 #include <asm/arch/gpio.h> 25 #endif 26 #endif 27 #include <i2c.h> 28 29 #if defined(CONFIG_SOFT_I2C_GPIO_SCL) 30 # include <asm/gpio.h> 31 32 # ifndef I2C_GPIO_SYNC 33 # define I2C_GPIO_SYNC 34 # endif 35 36 # ifndef I2C_INIT 37 # define I2C_INIT \ 38 do { \ 39 gpio_request(CONFIG_SOFT_I2C_GPIO_SCL, "soft_i2c"); \ 40 gpio_request(CONFIG_SOFT_I2C_GPIO_SDA, "soft_i2c"); \ 41 } while (0) 42 # endif 43 44 # ifndef I2C_ACTIVE 45 # define I2C_ACTIVE do { } while (0) 46 # endif 47 48 # ifndef I2C_TRISTATE 49 # define I2C_TRISTATE do { } while (0) 50 # endif 51 52 # ifndef I2C_READ 53 # define I2C_READ gpio_get_value(CONFIG_SOFT_I2C_GPIO_SDA) 54 # endif 55 56 # ifndef I2C_SDA 57 # define I2C_SDA(bit) \ 58 do { \ 59 if (bit) \ 60 gpio_direction_input(CONFIG_SOFT_I2C_GPIO_SDA); \ 61 else \ 62 gpio_direction_output(CONFIG_SOFT_I2C_GPIO_SDA, 0); \ 63 I2C_GPIO_SYNC; \ 64 } while (0) 65 # endif 66 67 # ifndef I2C_SCL 68 # define I2C_SCL(bit) \ 69 do { \ 70 gpio_direction_output(CONFIG_SOFT_I2C_GPIO_SCL, bit); \ 71 I2C_GPIO_SYNC; \ 72 } while (0) 73 # endif 74 75 # ifndef I2C_DELAY 76 # define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ 77 # endif 78 79 #endif 80 81 /* #define DEBUG_I2C */ 82 83 DECLARE_GLOBAL_DATA_PTR; 84 85 #ifndef I2C_SOFT_DECLARATIONS 86 # define I2C_SOFT_DECLARATIONS 87 #endif 88 89 #if !defined(CONFIG_SYS_I2C_SOFT_SPEED) 90 #define CONFIG_SYS_I2C_SOFT_SPEED CONFIG_SYS_I2C_SPEED 91 #endif 92 #if !defined(CONFIG_SYS_I2C_SOFT_SLAVE) 93 #define CONFIG_SYS_I2C_SOFT_SLAVE CONFIG_SYS_I2C_SLAVE 94 #endif 95 96 /*----------------------------------------------------------------------- 97 * Definitions 98 */ 99 #define RETRIES 0 100 101 #define I2C_ACK 0 /* PD_SDA level to ack a byte */ 102 #define I2C_NOACK 1 /* PD_SDA level to noack a byte */ 103 104 105 #ifdef DEBUG_I2C 106 #define PRINTD(fmt,args...) do { \ 107 printf (fmt ,##args); \ 108 } while (0) 109 #else 110 #define PRINTD(fmt,args...) 111 #endif 112 113 /*----------------------------------------------------------------------- 114 * Local functions 115 */ 116 #if !defined(CONFIG_SYS_I2C_INIT_BOARD) 117 static void send_reset (void); 118 #endif 119 static void send_start (void); 120 static void send_stop (void); 121 static void send_ack (int); 122 static int write_byte (uchar byte); 123 static uchar read_byte (int); 124 125 #if !defined(CONFIG_SYS_I2C_INIT_BOARD) 126 /*----------------------------------------------------------------------- 127 * Send a reset sequence consisting of 9 clocks with the data signal high 128 * to clock any confused device back into an idle state. Also send a 129 * <stop> at the end of the sequence for belts & suspenders. 130 */ 131 static void send_reset(void) 132 { 133 I2C_SOFT_DECLARATIONS /* intentional without ';' */ 134 int j; 135 136 I2C_SCL(1); 137 I2C_SDA(1); 138 #ifdef I2C_INIT 139 I2C_INIT; 140 #endif 141 I2C_TRISTATE; 142 for(j = 0; j < 9; j++) { 143 I2C_SCL(0); 144 I2C_DELAY; 145 I2C_DELAY; 146 I2C_SCL(1); 147 I2C_DELAY; 148 I2C_DELAY; 149 } 150 send_stop(); 151 I2C_TRISTATE; 152 } 153 #endif 154 155 /*----------------------------------------------------------------------- 156 * START: High -> Low on SDA while SCL is High 157 */ 158 static void send_start(void) 159 { 160 I2C_SOFT_DECLARATIONS /* intentional without ';' */ 161 162 I2C_DELAY; 163 I2C_SDA(1); 164 I2C_ACTIVE; 165 I2C_DELAY; 166 I2C_SCL(1); 167 I2C_DELAY; 168 I2C_SDA(0); 169 I2C_DELAY; 170 } 171 172 /*----------------------------------------------------------------------- 173 * STOP: Low -> High on SDA while SCL is High 174 */ 175 static void send_stop(void) 176 { 177 I2C_SOFT_DECLARATIONS /* intentional without ';' */ 178 179 I2C_SCL(0); 180 I2C_DELAY; 181 I2C_SDA(0); 182 I2C_ACTIVE; 183 I2C_DELAY; 184 I2C_SCL(1); 185 I2C_DELAY; 186 I2C_SDA(1); 187 I2C_DELAY; 188 I2C_TRISTATE; 189 } 190 191 /*----------------------------------------------------------------------- 192 * ack should be I2C_ACK or I2C_NOACK 193 */ 194 static void send_ack(int ack) 195 { 196 I2C_SOFT_DECLARATIONS /* intentional without ';' */ 197 198 I2C_SCL(0); 199 I2C_DELAY; 200 I2C_ACTIVE; 201 I2C_SDA(ack); 202 I2C_DELAY; 203 I2C_SCL(1); 204 I2C_DELAY; 205 I2C_DELAY; 206 I2C_SCL(0); 207 I2C_DELAY; 208 } 209 210 /*----------------------------------------------------------------------- 211 * Send 8 bits and look for an acknowledgement. 212 */ 213 static int write_byte(uchar data) 214 { 215 I2C_SOFT_DECLARATIONS /* intentional without ';' */ 216 int j; 217 int nack; 218 219 I2C_ACTIVE; 220 for(j = 0; j < 8; j++) { 221 I2C_SCL(0); 222 I2C_DELAY; 223 I2C_SDA(data & 0x80); 224 I2C_DELAY; 225 I2C_SCL(1); 226 I2C_DELAY; 227 I2C_DELAY; 228 229 data <<= 1; 230 } 231 232 /* 233 * Look for an <ACK>(negative logic) and return it. 234 */ 235 I2C_SCL(0); 236 I2C_DELAY; 237 I2C_SDA(1); 238 I2C_TRISTATE; 239 I2C_DELAY; 240 I2C_SCL(1); 241 I2C_DELAY; 242 I2C_DELAY; 243 nack = I2C_READ; 244 I2C_SCL(0); 245 I2C_DELAY; 246 I2C_ACTIVE; 247 248 return(nack); /* not a nack is an ack */ 249 } 250 251 /*----------------------------------------------------------------------- 252 * if ack == I2C_ACK, ACK the byte so can continue reading, else 253 * send I2C_NOACK to end the read. 254 */ 255 static uchar read_byte(int ack) 256 { 257 I2C_SOFT_DECLARATIONS /* intentional without ';' */ 258 int data; 259 int j; 260 261 /* 262 * Read 8 bits, MSB first. 263 */ 264 I2C_TRISTATE; 265 I2C_SDA(1); 266 data = 0; 267 for(j = 0; j < 8; j++) { 268 I2C_SCL(0); 269 I2C_DELAY; 270 I2C_SCL(1); 271 I2C_DELAY; 272 data <<= 1; 273 data |= I2C_READ; 274 I2C_DELAY; 275 } 276 send_ack(ack); 277 278 return(data); 279 } 280 281 /*----------------------------------------------------------------------- 282 * Initialization 283 */ 284 static void soft_i2c_init(struct i2c_adapter *adap, int speed, int slaveaddr) 285 { 286 #if defined(CONFIG_SYS_I2C_INIT_BOARD) 287 /* call board specific i2c bus reset routine before accessing the */ 288 /* environment, which might be in a chip on that bus. For details */ 289 /* about this problem see doc/I2C_Edge_Conditions. */ 290 i2c_init_board(); 291 #else 292 /* 293 * WARNING: Do NOT save speed in a static variable: if the 294 * I2C routines are called before RAM is initialized (to read 295 * the DIMM SPD, for instance), RAM won't be usable and your 296 * system will crash. 297 */ 298 send_reset (); 299 #endif 300 } 301 302 /*----------------------------------------------------------------------- 303 * Probe to see if a chip is present. Also good for checking for the 304 * completion of EEPROM writes since the chip stops responding until 305 * the write completes (typically 10mSec). 306 */ 307 static int soft_i2c_probe(struct i2c_adapter *adap, uint8_t addr) 308 { 309 int rc; 310 311 /* 312 * perform 1 byte write transaction with just address byte 313 * (fake write) 314 */ 315 send_start(); 316 rc = write_byte ((addr << 1) | 0); 317 send_stop(); 318 319 return (rc ? 1 : 0); 320 } 321 322 /*----------------------------------------------------------------------- 323 * Read bytes 324 */ 325 static int soft_i2c_read(struct i2c_adapter *adap, uchar chip, uint addr, 326 int alen, uchar *buffer, int len) 327 { 328 int shift; 329 PRINTD("i2c_read: chip %02X addr %02X alen %d buffer %p len %d\n", 330 chip, addr, alen, buffer, len); 331 332 #ifdef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 333 /* 334 * EEPROM chips that implement "address overflow" are ones 335 * like Catalyst 24WC04/08/16 which has 9/10/11 bits of 336 * address and the extra bits end up in the "chip address" 337 * bit slots. This makes a 24WC08 (1Kbyte) chip look like 338 * four 256 byte chips. 339 * 340 * Note that we consider the length of the address field to 341 * still be one byte because the extra address bits are 342 * hidden in the chip address. 343 */ 344 chip |= ((addr >> (alen * 8)) & CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW); 345 346 PRINTD("i2c_read: fix addr_overflow: chip %02X addr %02X\n", 347 chip, addr); 348 #endif 349 350 /* 351 * Do the addressing portion of a write cycle to set the 352 * chip's address pointer. If the address length is zero, 353 * don't do the normal write cycle to set the address pointer, 354 * there is no address pointer in this chip. 355 */ 356 send_start(); 357 if(alen > 0) { 358 if(write_byte(chip << 1)) { /* write cycle */ 359 send_stop(); 360 PRINTD("i2c_read, no chip responded %02X\n", chip); 361 return(1); 362 } 363 shift = (alen-1) * 8; 364 while(alen-- > 0) { 365 if(write_byte(addr >> shift)) { 366 PRINTD("i2c_read, address not <ACK>ed\n"); 367 return(1); 368 } 369 shift -= 8; 370 } 371 372 /* Some I2C chips need a stop/start sequence here, 373 * other chips don't work with a full stop and need 374 * only a start. Default behaviour is to send the 375 * stop/start sequence. 376 */ 377 #ifdef CONFIG_SOFT_I2C_READ_REPEATED_START 378 send_start(); 379 #else 380 send_stop(); 381 send_start(); 382 #endif 383 } 384 /* 385 * Send the chip address again, this time for a read cycle. 386 * Then read the data. On the last byte, we do a NACK instead 387 * of an ACK(len == 0) to terminate the read. 388 */ 389 write_byte((chip << 1) | 1); /* read cycle */ 390 while(len-- > 0) { 391 *buffer++ = read_byte(len == 0); 392 } 393 send_stop(); 394 return(0); 395 } 396 397 /*----------------------------------------------------------------------- 398 * Write bytes 399 */ 400 static int soft_i2c_write(struct i2c_adapter *adap, uchar chip, uint addr, 401 int alen, uchar *buffer, int len) 402 { 403 int shift, failures = 0; 404 405 PRINTD("i2c_write: chip %02X addr %02X alen %d buffer %p len %d\n", 406 chip, addr, alen, buffer, len); 407 408 send_start(); 409 if(write_byte(chip << 1)) { /* write cycle */ 410 send_stop(); 411 PRINTD("i2c_write, no chip responded %02X\n", chip); 412 return(1); 413 } 414 shift = (alen-1) * 8; 415 while(alen-- > 0) { 416 if(write_byte(addr >> shift)) { 417 PRINTD("i2c_write, address not <ACK>ed\n"); 418 return(1); 419 } 420 shift -= 8; 421 } 422 423 while(len-- > 0) { 424 if(write_byte(*buffer++)) { 425 failures++; 426 } 427 } 428 send_stop(); 429 return(failures); 430 } 431 432 /* 433 * Register soft i2c adapters 434 */ 435 U_BOOT_I2C_ADAP_COMPLETE(soft00, soft_i2c_init, soft_i2c_probe, 436 soft_i2c_read, soft_i2c_write, NULL, 437 CONFIG_SYS_I2C_SOFT_SPEED, CONFIG_SYS_I2C_SOFT_SLAVE, 438 0) 439 #if defined(I2C_SOFT_DECLARATIONS2) 440 U_BOOT_I2C_ADAP_COMPLETE(soft01, soft_i2c_init, soft_i2c_probe, 441 soft_i2c_read, soft_i2c_write, NULL, 442 CONFIG_SYS_I2C_SOFT_SPEED_2, 443 CONFIG_SYS_I2C_SOFT_SLAVE_2, 444 1) 445 #endif 446 #if defined(I2C_SOFT_DECLARATIONS3) 447 U_BOOT_I2C_ADAP_COMPLETE(soft02, soft_i2c_init, soft_i2c_probe, 448 soft_i2c_read, soft_i2c_write, NULL, 449 CONFIG_SYS_I2C_SOFT_SPEED_3, 450 CONFIG_SYS_I2C_SOFT_SLAVE_3, 451 2) 452 #endif 453 #if defined(I2C_SOFT_DECLARATIONS4) 454 U_BOOT_I2C_ADAP_COMPLETE(soft03, soft_i2c_init, soft_i2c_probe, 455 soft_i2c_read, soft_i2c_write, NULL, 456 CONFIG_SYS_I2C_SOFT_SPEED_4, 457 CONFIG_SYS_I2C_SOFT_SLAVE_4, 458 3) 459 #endif 460 #if defined(I2C_SOFT_DECLARATIONS5) 461 U_BOOT_I2C_ADAP_COMPLETE(soft04, soft_i2c_init, soft_i2c_probe, 462 soft_i2c_read, soft_i2c_write, NULL, 463 CONFIG_SYS_I2C_SOFT_SPEED_5, 464 CONFIG_SYS_I2C_SOFT_SLAVE_5, 465 4) 466 #endif 467 #if defined(I2C_SOFT_DECLARATIONS6) 468 U_BOOT_I2C_ADAP_COMPLETE(soft05, soft_i2c_init, soft_i2c_probe, 469 soft_i2c_read, soft_i2c_write, NULL, 470 CONFIG_SYS_I2C_SOFT_SPEED_6, 471 CONFIG_SYS_I2C_SOFT_SLAVE_6, 472 5) 473 #endif 474 #if defined(I2C_SOFT_DECLARATIONS7) 475 U_BOOT_I2C_ADAP_COMPLETE(soft06, soft_i2c_init, soft_i2c_probe, 476 soft_i2c_read, soft_i2c_write, NULL, 477 CONFIG_SYS_I2C_SOFT_SPEED_7, 478 CONFIG_SYS_I2C_SOFT_SLAVE_7, 479 6) 480 #endif 481 #if defined(I2C_SOFT_DECLARATIONS8) 482 U_BOOT_I2C_ADAP_COMPLETE(soft07, soft_i2c_init, soft_i2c_probe, 483 soft_i2c_read, soft_i2c_write, NULL, 484 CONFIG_SYS_I2C_SOFT_SPEED_8, 485 CONFIG_SYS_I2C_SOFT_SLAVE_8, 486 7) 487 #endif 488 #if defined(I2C_SOFT_DECLARATIONS9) 489 U_BOOT_I2C_ADAP_COMPLETE(soft08, soft_i2c_init, soft_i2c_probe, 490 soft_i2c_read, soft_i2c_write, NULL, 491 CONFIG_SYS_I2C_SOFT_SPEED_9, 492 CONFIG_SYS_I2C_SOFT_SLAVE_9, 493 8) 494 #endif 495 #if defined(I2C_SOFT_DECLARATIONS10) 496 U_BOOT_I2C_ADAP_COMPLETE(soft09, soft_i2c_init, soft_i2c_probe, 497 soft_i2c_read, soft_i2c_write, NULL, 498 CONFIG_SYS_I2C_SOFT_SPEED_10, 499 CONFIG_SYS_I2C_SOFT_SLAVE_10, 500 9) 501 #endif 502 #if defined(I2C_SOFT_DECLARATIONS11) 503 U_BOOT_I2C_ADAP_COMPLETE(soft10, soft_i2c_init, soft_i2c_probe, 504 soft_i2c_read, soft_i2c_write, NULL, 505 CONFIG_SYS_I2C_SOFT_SPEED_11, 506 CONFIG_SYS_I2C_SOFT_SLAVE_11, 507 10) 508 #endif 509 #if defined(I2C_SOFT_DECLARATIONS12) 510 U_BOOT_I2C_ADAP_COMPLETE(soft11, soft_i2c_init, soft_i2c_probe, 511 soft_i2c_read, soft_i2c_write, NULL, 512 CONFIG_SYS_I2C_SOFT_SPEED_12, 513 CONFIG_SYS_I2C_SOFT_SLAVE_12, 514 11) 515 #endif 516