1 /* 2 * (C) Copyright 2002 3 * David Mueller, ELSOFT AG, d.mueller@elsoft.ch 4 * 5 * SPDX-License-Identifier: GPL-2.0+ 6 */ 7 8 /* This code should work for both the S3C2400 and the S3C2410 9 * as they seem to have the same I2C controller inside. 10 * The different address mapping is handled by the s3c24xx.h files below. 11 */ 12 #include <common.h> 13 #include <errno.h> 14 #include <dm.h> 15 #include <fdtdec.h> 16 #if (defined CONFIG_EXYNOS4 || defined CONFIG_EXYNOS5) 17 #include <asm/arch/clk.h> 18 #include <asm/arch/cpu.h> 19 #include <asm/arch/pinmux.h> 20 #else 21 #include <asm/arch/s3c24x0_cpu.h> 22 #endif 23 #include <asm/io.h> 24 #include <i2c.h> 25 #include "s3c24x0_i2c.h" 26 27 #define I2C_WRITE 0 28 #define I2C_READ 1 29 30 #define I2C_OK 0 31 #define I2C_NOK 1 32 #define I2C_NACK 2 33 #define I2C_NOK_LA 3 /* Lost arbitration */ 34 #define I2C_NOK_TOUT 4 /* time out */ 35 36 /* HSI2C specific register description */ 37 38 /* I2C_CTL Register bits */ 39 #define HSI2C_FUNC_MODE_I2C (1u << 0) 40 #define HSI2C_MASTER (1u << 3) 41 #define HSI2C_RXCHON (1u << 6) /* Write/Send */ 42 #define HSI2C_TXCHON (1u << 7) /* Read/Receive */ 43 #define HSI2C_SW_RST (1u << 31) 44 45 /* I2C_FIFO_CTL Register bits */ 46 #define HSI2C_RXFIFO_EN (1u << 0) 47 #define HSI2C_TXFIFO_EN (1u << 1) 48 #define HSI2C_TXFIFO_TRIGGER_LEVEL (0x20 << 16) 49 #define HSI2C_RXFIFO_TRIGGER_LEVEL (0x20 << 4) 50 51 /* I2C_TRAILING_CTL Register bits */ 52 #define HSI2C_TRAILING_COUNT (0xff) 53 54 /* I2C_INT_EN Register bits */ 55 #define HSI2C_TX_UNDERRUN_EN (1u << 2) 56 #define HSI2C_TX_OVERRUN_EN (1u << 3) 57 #define HSI2C_RX_UNDERRUN_EN (1u << 4) 58 #define HSI2C_RX_OVERRUN_EN (1u << 5) 59 #define HSI2C_INT_TRAILING_EN (1u << 6) 60 #define HSI2C_INT_I2C_EN (1u << 9) 61 62 #define HSI2C_INT_ERROR_MASK (HSI2C_TX_UNDERRUN_EN |\ 63 HSI2C_TX_OVERRUN_EN |\ 64 HSI2C_RX_UNDERRUN_EN |\ 65 HSI2C_RX_OVERRUN_EN |\ 66 HSI2C_INT_TRAILING_EN) 67 68 /* I2C_CONF Register bits */ 69 #define HSI2C_AUTO_MODE (1u << 31) 70 #define HSI2C_10BIT_ADDR_MODE (1u << 30) 71 #define HSI2C_HS_MODE (1u << 29) 72 73 /* I2C_AUTO_CONF Register bits */ 74 #define HSI2C_READ_WRITE (1u << 16) 75 #define HSI2C_STOP_AFTER_TRANS (1u << 17) 76 #define HSI2C_MASTER_RUN (1u << 31) 77 78 /* I2C_TIMEOUT Register bits */ 79 #define HSI2C_TIMEOUT_EN (1u << 31) 80 81 /* I2C_TRANS_STATUS register bits */ 82 #define HSI2C_MASTER_BUSY (1u << 17) 83 #define HSI2C_SLAVE_BUSY (1u << 16) 84 #define HSI2C_TIMEOUT_AUTO (1u << 4) 85 #define HSI2C_NO_DEV (1u << 3) 86 #define HSI2C_NO_DEV_ACK (1u << 2) 87 #define HSI2C_TRANS_ABORT (1u << 1) 88 #define HSI2C_TRANS_SUCCESS (1u << 0) 89 #define HSI2C_TRANS_ERROR_MASK (HSI2C_TIMEOUT_AUTO |\ 90 HSI2C_NO_DEV | HSI2C_NO_DEV_ACK |\ 91 HSI2C_TRANS_ABORT) 92 #define HSI2C_TRANS_FINISHED_MASK (HSI2C_TRANS_ERROR_MASK | HSI2C_TRANS_SUCCESS) 93 94 95 /* I2C_FIFO_STAT Register bits */ 96 #define HSI2C_RX_FIFO_EMPTY (1u << 24) 97 #define HSI2C_RX_FIFO_FULL (1u << 23) 98 #define HSI2C_TX_FIFO_EMPTY (1u << 8) 99 #define HSI2C_TX_FIFO_FULL (1u << 7) 100 #define HSI2C_RX_FIFO_LEVEL(x) (((x) >> 16) & 0x7f) 101 #define HSI2C_TX_FIFO_LEVEL(x) ((x) & 0x7f) 102 103 #define HSI2C_SLV_ADDR_MAS(x) ((x & 0x3ff) << 10) 104 105 /* S3C I2C Controller bits */ 106 #define I2CSTAT_BSY 0x20 /* Busy bit */ 107 #define I2CSTAT_NACK 0x01 /* Nack bit */ 108 #define I2CCON_ACKGEN 0x80 /* Acknowledge generation */ 109 #define I2CCON_IRPND 0x10 /* Interrupt pending bit */ 110 #define I2C_MODE_MT 0xC0 /* Master Transmit Mode */ 111 #define I2C_MODE_MR 0x80 /* Master Receive Mode */ 112 #define I2C_START_STOP 0x20 /* START / STOP */ 113 #define I2C_TXRX_ENA 0x10 /* I2C Tx/Rx enable */ 114 115 #define I2C_TIMEOUT_MS 1000 /* 1 second */ 116 117 #define HSI2C_TIMEOUT_US 100000 /* 100 ms, finer granularity */ 118 119 120 /* To support VCMA9 boards and other who dont define max_i2c_num */ 121 #ifndef CONFIG_MAX_I2C_NUM 122 #define CONFIG_MAX_I2C_NUM 1 123 #endif 124 125 DECLARE_GLOBAL_DATA_PTR; 126 127 /* 128 * For SPL boot some boards need i2c before SDRAM is initialised so force 129 * variables to live in SRAM 130 */ 131 #ifdef CONFIG_SYS_I2C 132 static struct s3c24x0_i2c_bus i2c_bus[CONFIG_MAX_I2C_NUM] 133 __attribute__((section(".data"))); 134 #endif 135 136 enum exynos_i2c_type { 137 EXYNOS_I2C_STD, 138 EXYNOS_I2C_HS, 139 }; 140 141 #ifdef CONFIG_SYS_I2C 142 /** 143 * Get a pointer to the given bus index 144 * 145 * @bus_idx: Bus index to look up 146 * @return pointer to bus, or NULL if invalid or not available 147 */ 148 static struct s3c24x0_i2c_bus *get_bus(unsigned int bus_idx) 149 { 150 if (bus_idx < ARRAY_SIZE(i2c_bus)) { 151 struct s3c24x0_i2c_bus *bus; 152 153 bus = &i2c_bus[bus_idx]; 154 if (bus->active) 155 return bus; 156 } 157 158 debug("Undefined bus: %d\n", bus_idx); 159 return NULL; 160 } 161 #endif 162 163 #if !(defined CONFIG_EXYNOS4 || defined CONFIG_EXYNOS5) 164 static int GetI2CSDA(void) 165 { 166 struct s3c24x0_gpio *gpio = s3c24x0_get_base_gpio(); 167 168 #ifdef CONFIG_S3C2410 169 return (readl(&gpio->gpedat) & 0x8000) >> 15; 170 #endif 171 #ifdef CONFIG_S3C2400 172 return (readl(&gpio->pgdat) & 0x0020) >> 5; 173 #endif 174 } 175 176 static void SetI2CSCL(int x) 177 { 178 struct s3c24x0_gpio *gpio = s3c24x0_get_base_gpio(); 179 180 #ifdef CONFIG_S3C2410 181 writel((readl(&gpio->gpedat) & ~0x4000) | 182 (x & 1) << 14, &gpio->gpedat); 183 #endif 184 #ifdef CONFIG_S3C2400 185 writel((readl(&gpio->pgdat) & ~0x0040) | (x & 1) << 6, &gpio->pgdat); 186 #endif 187 } 188 #endif 189 190 /* 191 * Wait til the byte transfer is completed. 192 * 193 * @param i2c- pointer to the appropriate i2c register bank. 194 * @return I2C_OK, if transmission was ACKED 195 * I2C_NACK, if transmission was NACKED 196 * I2C_NOK_TIMEOUT, if transaction did not complete in I2C_TIMEOUT_MS 197 */ 198 199 static int WaitForXfer(struct s3c24x0_i2c *i2c) 200 { 201 ulong start_time = get_timer(0); 202 203 do { 204 if (readl(&i2c->iiccon) & I2CCON_IRPND) 205 return (readl(&i2c->iicstat) & I2CSTAT_NACK) ? 206 I2C_NACK : I2C_OK; 207 } while (get_timer(start_time) < I2C_TIMEOUT_MS); 208 209 return I2C_NOK_TOUT; 210 } 211 212 /* 213 * Wait for transfer completion. 214 * 215 * This function reads the interrupt status register waiting for the INT_I2C 216 * bit to be set, which indicates copletion of a transaction. 217 * 218 * @param i2c: pointer to the appropriate register bank 219 * 220 * @return: I2C_OK in case of successful completion, I2C_NOK_TIMEOUT in case 221 * the status bits do not get set in time, or an approrpiate error 222 * value in case of transfer errors. 223 */ 224 static int hsi2c_wait_for_trx(struct exynos5_hsi2c *i2c) 225 { 226 int i = HSI2C_TIMEOUT_US; 227 228 while (i-- > 0) { 229 u32 int_status = readl(&i2c->usi_int_stat); 230 231 if (int_status & HSI2C_INT_I2C_EN) { 232 u32 trans_status = readl(&i2c->usi_trans_status); 233 234 /* Deassert pending interrupt. */ 235 writel(int_status, &i2c->usi_int_stat); 236 237 if (trans_status & HSI2C_NO_DEV_ACK) { 238 debug("%s: no ACK from device\n", __func__); 239 return I2C_NACK; 240 } 241 if (trans_status & HSI2C_NO_DEV) { 242 debug("%s: no device\n", __func__); 243 return I2C_NOK; 244 } 245 if (trans_status & HSI2C_TRANS_ABORT) { 246 debug("%s: arbitration lost\n", __func__); 247 return I2C_NOK_LA; 248 } 249 if (trans_status & HSI2C_TIMEOUT_AUTO) { 250 debug("%s: device timed out\n", __func__); 251 return I2C_NOK_TOUT; 252 } 253 return I2C_OK; 254 } 255 udelay(1); 256 } 257 debug("%s: transaction timeout!\n", __func__); 258 return I2C_NOK_TOUT; 259 } 260 261 static void ReadWriteByte(struct s3c24x0_i2c *i2c) 262 { 263 writel(readl(&i2c->iiccon) & ~I2CCON_IRPND, &i2c->iiccon); 264 } 265 266 #ifdef CONFIG_SYS_I2C 267 static struct s3c24x0_i2c *get_base_i2c(int bus) 268 { 269 #ifdef CONFIG_EXYNOS4 270 struct s3c24x0_i2c *i2c = (struct s3c24x0_i2c *)(samsung_get_base_i2c() 271 + (EXYNOS4_I2C_SPACING 272 * bus)); 273 return i2c; 274 #elif defined CONFIG_EXYNOS5 275 struct s3c24x0_i2c *i2c = (struct s3c24x0_i2c *)(samsung_get_base_i2c() 276 + (EXYNOS5_I2C_SPACING 277 * bus)); 278 return i2c; 279 #else 280 return s3c24x0_get_base_i2c(); 281 #endif 282 } 283 #endif 284 285 static void i2c_ch_init(struct s3c24x0_i2c *i2c, int speed, int slaveadd) 286 { 287 ulong freq, pres = 16, div; 288 #if (defined CONFIG_EXYNOS4 || defined CONFIG_EXYNOS5) 289 freq = get_i2c_clk(); 290 #else 291 freq = get_PCLK(); 292 #endif 293 /* calculate prescaler and divisor values */ 294 if ((freq / pres / (16 + 1)) > speed) 295 /* set prescaler to 512 */ 296 pres = 512; 297 298 div = 0; 299 while ((freq / pres / (div + 1)) > speed) 300 div++; 301 302 /* set prescaler, divisor according to freq, also set ACKGEN, IRQ */ 303 writel((div & 0x0F) | 0xA0 | ((pres == 512) ? 0x40 : 0), &i2c->iiccon); 304 305 /* init to SLAVE REVEIVE and set slaveaddr */ 306 writel(0, &i2c->iicstat); 307 writel(slaveadd, &i2c->iicadd); 308 /* program Master Transmit (and implicit STOP) */ 309 writel(I2C_MODE_MT | I2C_TXRX_ENA, &i2c->iicstat); 310 } 311 312 static int hsi2c_get_clk_details(struct s3c24x0_i2c_bus *i2c_bus) 313 { 314 struct exynos5_hsi2c *hsregs = i2c_bus->hsregs; 315 ulong clkin; 316 unsigned int op_clk = i2c_bus->clock_frequency; 317 unsigned int i = 0, utemp0 = 0, utemp1 = 0; 318 unsigned int t_ftl_cycle; 319 320 #if (defined CONFIG_EXYNOS4 || defined CONFIG_EXYNOS5) 321 clkin = get_i2c_clk(); 322 #else 323 clkin = get_PCLK(); 324 #endif 325 /* FPCLK / FI2C = 326 * (CLK_DIV + 1) * (TSCLK_L + TSCLK_H + 2) + 8 + 2 * FLT_CYCLE 327 * uTemp0 = (CLK_DIV + 1) * (TSCLK_L + TSCLK_H + 2) 328 * uTemp1 = (TSCLK_L + TSCLK_H + 2) 329 * uTemp2 = TSCLK_L + TSCLK_H 330 */ 331 t_ftl_cycle = (readl(&hsregs->usi_conf) >> 16) & 0x7; 332 utemp0 = (clkin / op_clk) - 8 - 2 * t_ftl_cycle; 333 334 /* CLK_DIV max is 256 */ 335 for (i = 0; i < 256; i++) { 336 utemp1 = utemp0 / (i + 1); 337 if ((utemp1 < 512) && (utemp1 > 4)) { 338 i2c_bus->clk_cycle = utemp1 - 2; 339 i2c_bus->clk_div = i; 340 return 0; 341 } 342 } 343 return -EINVAL; 344 } 345 346 static void hsi2c_ch_init(struct s3c24x0_i2c_bus *i2c_bus) 347 { 348 struct exynos5_hsi2c *hsregs = i2c_bus->hsregs; 349 unsigned int t_sr_release; 350 unsigned int n_clkdiv; 351 unsigned int t_start_su, t_start_hd; 352 unsigned int t_stop_su; 353 unsigned int t_data_su, t_data_hd; 354 unsigned int t_scl_l, t_scl_h; 355 u32 i2c_timing_s1; 356 u32 i2c_timing_s2; 357 u32 i2c_timing_s3; 358 u32 i2c_timing_sla; 359 360 n_clkdiv = i2c_bus->clk_div; 361 t_scl_l = i2c_bus->clk_cycle / 2; 362 t_scl_h = i2c_bus->clk_cycle / 2; 363 t_start_su = t_scl_l; 364 t_start_hd = t_scl_l; 365 t_stop_su = t_scl_l; 366 t_data_su = t_scl_l / 2; 367 t_data_hd = t_scl_l / 2; 368 t_sr_release = i2c_bus->clk_cycle; 369 370 i2c_timing_s1 = t_start_su << 24 | t_start_hd << 16 | t_stop_su << 8; 371 i2c_timing_s2 = t_data_su << 24 | t_scl_l << 8 | t_scl_h << 0; 372 i2c_timing_s3 = n_clkdiv << 16 | t_sr_release << 0; 373 i2c_timing_sla = t_data_hd << 0; 374 375 writel(HSI2C_TRAILING_COUNT, &hsregs->usi_trailing_ctl); 376 377 /* Clear to enable Timeout */ 378 clrsetbits_le32(&hsregs->usi_timeout, HSI2C_TIMEOUT_EN, 0); 379 380 /* set AUTO mode */ 381 writel(readl(&hsregs->usi_conf) | HSI2C_AUTO_MODE, &hsregs->usi_conf); 382 383 /* Enable completion conditions' reporting. */ 384 writel(HSI2C_INT_I2C_EN, &hsregs->usi_int_en); 385 386 /* Enable FIFOs */ 387 writel(HSI2C_RXFIFO_EN | HSI2C_TXFIFO_EN, &hsregs->usi_fifo_ctl); 388 389 /* Currently operating in Fast speed mode. */ 390 writel(i2c_timing_s1, &hsregs->usi_timing_fs1); 391 writel(i2c_timing_s2, &hsregs->usi_timing_fs2); 392 writel(i2c_timing_s3, &hsregs->usi_timing_fs3); 393 writel(i2c_timing_sla, &hsregs->usi_timing_sla); 394 } 395 396 /* SW reset for the high speed bus */ 397 static void exynos5_i2c_reset(struct s3c24x0_i2c_bus *i2c_bus) 398 { 399 struct exynos5_hsi2c *i2c = i2c_bus->hsregs; 400 u32 i2c_ctl; 401 402 /* Set and clear the bit for reset */ 403 i2c_ctl = readl(&i2c->usi_ctl); 404 i2c_ctl |= HSI2C_SW_RST; 405 writel(i2c_ctl, &i2c->usi_ctl); 406 407 i2c_ctl = readl(&i2c->usi_ctl); 408 i2c_ctl &= ~HSI2C_SW_RST; 409 writel(i2c_ctl, &i2c->usi_ctl); 410 411 /* Initialize the configure registers */ 412 hsi2c_ch_init(i2c_bus); 413 } 414 415 #ifdef CONFIG_SYS_I2C 416 static void s3c24x0_i2c_init(struct i2c_adapter *adap, int speed, int slaveadd) 417 { 418 struct s3c24x0_i2c *i2c; 419 struct s3c24x0_i2c_bus *bus; 420 #if !(defined CONFIG_EXYNOS4 || defined CONFIG_EXYNOS5) 421 struct s3c24x0_gpio *gpio = s3c24x0_get_base_gpio(); 422 #endif 423 ulong start_time = get_timer(0); 424 425 i2c = get_base_i2c(adap->hwadapnr); 426 bus = &i2c_bus[adap->hwadapnr]; 427 if (!bus) 428 return; 429 430 /* 431 * In case the previous transfer is still going, wait to give it a 432 * chance to finish. 433 */ 434 while (readl(&i2c->iicstat) & I2CSTAT_BSY) { 435 if (get_timer(start_time) > I2C_TIMEOUT_MS) { 436 printf("%s: I2C bus busy for %p\n", __func__, 437 &i2c->iicstat); 438 return; 439 } 440 } 441 442 #if !(defined CONFIG_EXYNOS4 || defined CONFIG_EXYNOS5) 443 int i; 444 445 if ((readl(&i2c->iicstat) & I2CSTAT_BSY) || GetI2CSDA() == 0) { 446 #ifdef CONFIG_S3C2410 447 ulong old_gpecon = readl(&gpio->gpecon); 448 #endif 449 #ifdef CONFIG_S3C2400 450 ulong old_gpecon = readl(&gpio->pgcon); 451 #endif 452 /* bus still busy probably by (most) previously interrupted 453 transfer */ 454 455 #ifdef CONFIG_S3C2410 456 /* set I2CSDA and I2CSCL (GPE15, GPE14) to GPIO */ 457 writel((readl(&gpio->gpecon) & ~0xF0000000) | 0x10000000, 458 &gpio->gpecon); 459 #endif 460 #ifdef CONFIG_S3C2400 461 /* set I2CSDA and I2CSCL (PG5, PG6) to GPIO */ 462 writel((readl(&gpio->pgcon) & ~0x00003c00) | 0x00001000, 463 &gpio->pgcon); 464 #endif 465 466 /* toggle I2CSCL until bus idle */ 467 SetI2CSCL(0); 468 udelay(1000); 469 i = 10; 470 while ((i > 0) && (GetI2CSDA() != 1)) { 471 SetI2CSCL(1); 472 udelay(1000); 473 SetI2CSCL(0); 474 udelay(1000); 475 i--; 476 } 477 SetI2CSCL(1); 478 udelay(1000); 479 480 /* restore pin functions */ 481 #ifdef CONFIG_S3C2410 482 writel(old_gpecon, &gpio->gpecon); 483 #endif 484 #ifdef CONFIG_S3C2400 485 writel(old_gpecon, &gpio->pgcon); 486 #endif 487 } 488 #endif /* #if !(defined CONFIG_EXYNOS4 || defined CONFIG_EXYNOS5) */ 489 490 i2c_ch_init(i2c, speed, slaveadd); 491 492 bus->active = true; 493 bus->regs = i2c; 494 } 495 #endif /* CONFIG_SYS_I2C */ 496 497 /* 498 * Poll the appropriate bit of the fifo status register until the interface is 499 * ready to process the next byte or timeout expires. 500 * 501 * In addition to the FIFO status register this function also polls the 502 * interrupt status register to be able to detect unexpected transaction 503 * completion. 504 * 505 * When FIFO is ready to process the next byte, this function returns I2C_OK. 506 * If in course of polling the INT_I2C assertion is detected, the function 507 * returns I2C_NOK. If timeout happens before any of the above conditions is 508 * met - the function returns I2C_NOK_TOUT; 509 510 * @param i2c: pointer to the appropriate i2c register bank. 511 * @param rx_transfer: set to True if the receive transaction is in progress. 512 * @return: as described above. 513 */ 514 static unsigned hsi2c_poll_fifo(struct exynos5_hsi2c *i2c, bool rx_transfer) 515 { 516 u32 fifo_bit = rx_transfer ? HSI2C_RX_FIFO_EMPTY : HSI2C_TX_FIFO_FULL; 517 int i = HSI2C_TIMEOUT_US; 518 519 while (readl(&i2c->usi_fifo_stat) & fifo_bit) { 520 if (readl(&i2c->usi_int_stat) & HSI2C_INT_I2C_EN) { 521 /* 522 * There is a chance that assertion of 523 * HSI2C_INT_I2C_EN and deassertion of 524 * HSI2C_RX_FIFO_EMPTY happen simultaneously. Let's 525 * give FIFO status priority and check it one more 526 * time before reporting interrupt. The interrupt will 527 * be reported next time this function is called. 528 */ 529 if (rx_transfer && 530 !(readl(&i2c->usi_fifo_stat) & fifo_bit)) 531 break; 532 return I2C_NOK; 533 } 534 if (!i--) { 535 debug("%s: FIFO polling timeout!\n", __func__); 536 return I2C_NOK_TOUT; 537 } 538 udelay(1); 539 } 540 return I2C_OK; 541 } 542 543 /* 544 * Preapre hsi2c transaction, either read or write. 545 * 546 * Set up transfer as described in section 27.5.1.2 'I2C Channel Auto Mode' of 547 * the 5420 UM. 548 * 549 * @param i2c: pointer to the appropriate i2c register bank. 550 * @param chip: slave address on the i2c bus (with read/write bit exlcuded) 551 * @param len: number of bytes expected to be sent or received 552 * @param rx_transfer: set to true for receive transactions 553 * @param: issue_stop: set to true if i2c stop condition should be generated 554 * after this transaction. 555 * @return: I2C_NOK_TOUT in case the bus remained busy for HSI2C_TIMEOUT_US, 556 * I2C_OK otherwise. 557 */ 558 static int hsi2c_prepare_transaction(struct exynos5_hsi2c *i2c, 559 u8 chip, 560 u16 len, 561 bool rx_transfer, 562 bool issue_stop) 563 { 564 u32 conf; 565 566 conf = len | HSI2C_MASTER_RUN; 567 568 if (issue_stop) 569 conf |= HSI2C_STOP_AFTER_TRANS; 570 571 /* Clear to enable Timeout */ 572 writel(readl(&i2c->usi_timeout) & ~HSI2C_TIMEOUT_EN, &i2c->usi_timeout); 573 574 /* Set slave address */ 575 writel(HSI2C_SLV_ADDR_MAS(chip), &i2c->i2c_addr); 576 577 if (rx_transfer) { 578 /* i2c master, read transaction */ 579 writel((HSI2C_RXCHON | HSI2C_FUNC_MODE_I2C | HSI2C_MASTER), 580 &i2c->usi_ctl); 581 582 /* read up to len bytes, stop after transaction is finished */ 583 writel(conf | HSI2C_READ_WRITE, &i2c->usi_auto_conf); 584 } else { 585 /* i2c master, write transaction */ 586 writel((HSI2C_TXCHON | HSI2C_FUNC_MODE_I2C | HSI2C_MASTER), 587 &i2c->usi_ctl); 588 589 /* write up to len bytes, stop after transaction is finished */ 590 writel(conf, &i2c->usi_auto_conf); 591 } 592 593 /* Reset all pending interrupt status bits we care about, if any */ 594 writel(HSI2C_INT_I2C_EN, &i2c->usi_int_stat); 595 596 return I2C_OK; 597 } 598 599 /* 600 * Wait while i2c bus is settling down (mostly stop gets completed). 601 */ 602 static int hsi2c_wait_while_busy(struct exynos5_hsi2c *i2c) 603 { 604 int i = HSI2C_TIMEOUT_US; 605 606 while (readl(&i2c->usi_trans_status) & HSI2C_MASTER_BUSY) { 607 if (!i--) { 608 debug("%s: bus busy\n", __func__); 609 return I2C_NOK_TOUT; 610 } 611 udelay(1); 612 } 613 return I2C_OK; 614 } 615 616 static int hsi2c_write(struct exynos5_hsi2c *i2c, 617 unsigned char chip, 618 unsigned char addr[], 619 unsigned char alen, 620 unsigned char data[], 621 unsigned short len, 622 bool issue_stop) 623 { 624 int i, rv = 0; 625 626 if (!(len + alen)) { 627 /* Writes of zero length not supported in auto mode. */ 628 debug("%s: zero length writes not supported\n", __func__); 629 return I2C_NOK; 630 } 631 632 rv = hsi2c_prepare_transaction 633 (i2c, chip, len + alen, false, issue_stop); 634 if (rv != I2C_OK) 635 return rv; 636 637 /* Move address, if any, and the data, if any, into the FIFO. */ 638 for (i = 0; i < alen; i++) { 639 rv = hsi2c_poll_fifo(i2c, false); 640 if (rv != I2C_OK) { 641 debug("%s: address write failed\n", __func__); 642 goto write_error; 643 } 644 writel(addr[i], &i2c->usi_txdata); 645 } 646 647 for (i = 0; i < len; i++) { 648 rv = hsi2c_poll_fifo(i2c, false); 649 if (rv != I2C_OK) { 650 debug("%s: data write failed\n", __func__); 651 goto write_error; 652 } 653 writel(data[i], &i2c->usi_txdata); 654 } 655 656 rv = hsi2c_wait_for_trx(i2c); 657 658 write_error: 659 if (issue_stop) { 660 int tmp_ret = hsi2c_wait_while_busy(i2c); 661 if (rv == I2C_OK) 662 rv = tmp_ret; 663 } 664 665 writel(HSI2C_FUNC_MODE_I2C, &i2c->usi_ctl); /* done */ 666 return rv; 667 } 668 669 static int hsi2c_read(struct exynos5_hsi2c *i2c, 670 unsigned char chip, 671 unsigned char addr[], 672 unsigned char alen, 673 unsigned char data[], 674 unsigned short len) 675 { 676 int i, rv, tmp_ret; 677 bool drop_data = false; 678 679 if (!len) { 680 /* Reads of zero length not supported in auto mode. */ 681 debug("%s: zero length read adjusted\n", __func__); 682 drop_data = true; 683 len = 1; 684 } 685 686 if (alen) { 687 /* Internal register adress needs to be written first. */ 688 rv = hsi2c_write(i2c, chip, addr, alen, NULL, 0, false); 689 if (rv != I2C_OK) 690 return rv; 691 } 692 693 rv = hsi2c_prepare_transaction(i2c, chip, len, true, true); 694 695 if (rv != I2C_OK) 696 return rv; 697 698 for (i = 0; i < len; i++) { 699 rv = hsi2c_poll_fifo(i2c, true); 700 if (rv != I2C_OK) 701 goto read_err; 702 if (drop_data) 703 continue; 704 data[i] = readl(&i2c->usi_rxdata); 705 } 706 707 rv = hsi2c_wait_for_trx(i2c); 708 709 read_err: 710 tmp_ret = hsi2c_wait_while_busy(i2c); 711 if (rv == I2C_OK) 712 rv = tmp_ret; 713 714 writel(HSI2C_FUNC_MODE_I2C, &i2c->usi_ctl); /* done */ 715 return rv; 716 } 717 718 #ifdef CONFIG_SYS_I2C 719 static unsigned int s3c24x0_i2c_set_bus_speed(struct i2c_adapter *adap, 720 unsigned int speed) 721 #else 722 static int s3c24x0_i2c_set_bus_speed(struct udevice *dev, unsigned int speed) 723 #endif 724 { 725 struct s3c24x0_i2c_bus *i2c_bus; 726 727 #ifdef CONFIG_SYS_I2C 728 i2c_bus = get_bus(adap->hwadapnr); 729 if (!i2c_bus) 730 return -EFAULT; 731 #else 732 i2c_bus = dev_get_priv(dev); 733 #endif 734 i2c_bus->clock_frequency = speed; 735 736 if (i2c_bus->is_highspeed) { 737 if (hsi2c_get_clk_details(i2c_bus)) 738 return -EFAULT; 739 hsi2c_ch_init(i2c_bus); 740 } else { 741 i2c_ch_init(i2c_bus->regs, i2c_bus->clock_frequency, 742 CONFIG_SYS_I2C_S3C24X0_SLAVE); 743 } 744 745 return 0; 746 } 747 748 /* 749 * cmd_type is 0 for write, 1 for read. 750 * 751 * addr_len can take any value from 0-255, it is only limited 752 * by the char, we could make it larger if needed. If it is 753 * 0 we skip the address write cycle. 754 */ 755 static int i2c_transfer(struct s3c24x0_i2c *i2c, 756 unsigned char cmd_type, 757 unsigned char chip, 758 unsigned char addr[], 759 unsigned char addr_len, 760 unsigned char data[], 761 unsigned short data_len) 762 { 763 int i = 0, result; 764 ulong start_time = get_timer(0); 765 766 if (data == 0 || data_len == 0) { 767 /*Don't support data transfer of no length or to address 0 */ 768 debug("i2c_transfer: bad call\n"); 769 return I2C_NOK; 770 } 771 772 while (readl(&i2c->iicstat) & I2CSTAT_BSY) { 773 if (get_timer(start_time) > I2C_TIMEOUT_MS) 774 return I2C_NOK_TOUT; 775 } 776 777 writel(readl(&i2c->iiccon) | I2CCON_ACKGEN, &i2c->iiccon); 778 779 /* Get the slave chip address going */ 780 writel(chip, &i2c->iicds); 781 if ((cmd_type == I2C_WRITE) || (addr && addr_len)) 782 writel(I2C_MODE_MT | I2C_TXRX_ENA | I2C_START_STOP, 783 &i2c->iicstat); 784 else 785 writel(I2C_MODE_MR | I2C_TXRX_ENA | I2C_START_STOP, 786 &i2c->iicstat); 787 788 /* Wait for chip address to transmit. */ 789 result = WaitForXfer(i2c); 790 if (result != I2C_OK) 791 goto bailout; 792 793 /* If register address needs to be transmitted - do it now. */ 794 if (addr && addr_len) { 795 while ((i < addr_len) && (result == I2C_OK)) { 796 writel(addr[i++], &i2c->iicds); 797 ReadWriteByte(i2c); 798 result = WaitForXfer(i2c); 799 } 800 i = 0; 801 if (result != I2C_OK) 802 goto bailout; 803 } 804 805 switch (cmd_type) { 806 case I2C_WRITE: 807 while ((i < data_len) && (result == I2C_OK)) { 808 writel(data[i++], &i2c->iicds); 809 ReadWriteByte(i2c); 810 result = WaitForXfer(i2c); 811 } 812 break; 813 814 case I2C_READ: 815 if (addr && addr_len) { 816 /* 817 * Register address has been sent, now send slave chip 818 * address again to start the actual read transaction. 819 */ 820 writel(chip, &i2c->iicds); 821 822 /* Generate a re-START. */ 823 writel(I2C_MODE_MR | I2C_TXRX_ENA | I2C_START_STOP, 824 &i2c->iicstat); 825 ReadWriteByte(i2c); 826 result = WaitForXfer(i2c); 827 828 if (result != I2C_OK) 829 goto bailout; 830 } 831 832 while ((i < data_len) && (result == I2C_OK)) { 833 /* disable ACK for final READ */ 834 if (i == data_len - 1) 835 writel(readl(&i2c->iiccon) 836 & ~I2CCON_ACKGEN, 837 &i2c->iiccon); 838 ReadWriteByte(i2c); 839 result = WaitForXfer(i2c); 840 data[i++] = readl(&i2c->iicds); 841 } 842 if (result == I2C_NACK) 843 result = I2C_OK; /* Normal terminated read. */ 844 break; 845 846 default: 847 debug("i2c_transfer: bad call\n"); 848 result = I2C_NOK; 849 break; 850 } 851 852 bailout: 853 /* Send STOP. */ 854 writel(I2C_MODE_MR | I2C_TXRX_ENA, &i2c->iicstat); 855 ReadWriteByte(i2c); 856 857 return result; 858 } 859 860 #ifdef CONFIG_SYS_I2C 861 static int s3c24x0_i2c_probe(struct i2c_adapter *adap, uchar chip) 862 #else 863 static int s3c24x0_i2c_probe(struct udevice *dev, uint chip, uint chip_flags) 864 #endif 865 { 866 struct s3c24x0_i2c_bus *i2c_bus; 867 uchar buf[1]; 868 int ret; 869 870 #ifdef CONFIG_SYS_I2C 871 i2c_bus = get_bus(adap->hwadapnr); 872 if (!i2c_bus) 873 return -EFAULT; 874 #else 875 i2c_bus = dev_get_priv(dev); 876 #endif 877 buf[0] = 0; 878 879 /* 880 * What is needed is to send the chip address and verify that the 881 * address was <ACK>ed (i.e. there was a chip at that address which 882 * drove the data line low). 883 */ 884 if (i2c_bus->is_highspeed) { 885 ret = hsi2c_read(i2c_bus->hsregs, 886 chip, 0, 0, buf, 1); 887 } else { 888 ret = i2c_transfer(i2c_bus->regs, 889 I2C_READ, chip << 1, 0, 0, buf, 1); 890 } 891 892 return ret != I2C_OK; 893 } 894 895 #ifdef CONFIG_SYS_I2C 896 static int s3c24x0_i2c_read(struct i2c_adapter *adap, uchar chip, uint addr, 897 int alen, uchar *buffer, int len) 898 { 899 struct s3c24x0_i2c_bus *i2c_bus; 900 uchar xaddr[4]; 901 int ret; 902 903 i2c_bus = get_bus(adap->hwadapnr); 904 if (!i2c_bus) 905 return -EFAULT; 906 907 if (alen > 4) { 908 debug("I2C read: addr len %d not supported\n", alen); 909 return -EADDRNOTAVAIL; 910 } 911 912 if (alen > 0) { 913 xaddr[0] = (addr >> 24) & 0xFF; 914 xaddr[1] = (addr >> 16) & 0xFF; 915 xaddr[2] = (addr >> 8) & 0xFF; 916 xaddr[3] = addr & 0xFF; 917 } 918 919 #ifdef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 920 /* 921 * EEPROM chips that implement "address overflow" are ones 922 * like Catalyst 24WC04/08/16 which has 9/10/11 bits of 923 * address and the extra bits end up in the "chip address" 924 * bit slots. This makes a 24WC08 (1Kbyte) chip look like 925 * four 256 byte chips. 926 * 927 * Note that we consider the length of the address field to 928 * still be one byte because the extra address bits are 929 * hidden in the chip address. 930 */ 931 if (alen > 0) 932 chip |= ((addr >> (alen * 8)) & 933 CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW); 934 #endif 935 if (i2c_bus->is_highspeed) 936 ret = hsi2c_read(i2c_bus->hsregs, chip, &xaddr[4 - alen], 937 alen, buffer, len); 938 else 939 ret = i2c_transfer(i2c_bus->regs, I2C_READ, chip << 1, 940 &xaddr[4 - alen], alen, buffer, len); 941 942 if (ret) { 943 if (i2c_bus->is_highspeed) 944 exynos5_i2c_reset(i2c_bus); 945 debug("I2c read failed %d\n", ret); 946 return -EIO; 947 } 948 return 0; 949 } 950 951 static int s3c24x0_i2c_write(struct i2c_adapter *adap, uchar chip, uint addr, 952 int alen, uchar *buffer, int len) 953 { 954 struct s3c24x0_i2c_bus *i2c_bus; 955 uchar xaddr[4]; 956 int ret; 957 958 i2c_bus = get_bus(adap->hwadapnr); 959 if (!i2c_bus) 960 return -EFAULT; 961 962 if (alen > 4) { 963 debug("I2C write: addr len %d not supported\n", alen); 964 return -EINVAL; 965 } 966 967 if (alen > 0) { 968 xaddr[0] = (addr >> 24) & 0xFF; 969 xaddr[1] = (addr >> 16) & 0xFF; 970 xaddr[2] = (addr >> 8) & 0xFF; 971 xaddr[3] = addr & 0xFF; 972 } 973 #ifdef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 974 /* 975 * EEPROM chips that implement "address overflow" are ones 976 * like Catalyst 24WC04/08/16 which has 9/10/11 bits of 977 * address and the extra bits end up in the "chip address" 978 * bit slots. This makes a 24WC08 (1Kbyte) chip look like 979 * four 256 byte chips. 980 * 981 * Note that we consider the length of the address field to 982 * still be one byte because the extra address bits are 983 * hidden in the chip address. 984 */ 985 if (alen > 0) 986 chip |= ((addr >> (alen * 8)) & 987 CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW); 988 #endif 989 if (i2c_bus->is_highspeed) 990 ret = hsi2c_write(i2c_bus->hsregs, chip, &xaddr[4 - alen], 991 alen, buffer, len, true); 992 else 993 ret = i2c_transfer(i2c_bus->regs, I2C_WRITE, chip << 1, 994 &xaddr[4 - alen], alen, buffer, len); 995 996 if (ret != 0) { 997 if (i2c_bus->is_highspeed) 998 exynos5_i2c_reset(i2c_bus); 999 return 1; 1000 } else { 1001 return 0; 1002 } 1003 } 1004 1005 #ifdef CONFIG_OF_CONTROL 1006 static void process_nodes(const void *blob, int node_list[], int count, 1007 int is_highspeed) 1008 { 1009 struct s3c24x0_i2c_bus *bus; 1010 int i, flags; 1011 1012 for (i = 0; i < count; i++) { 1013 int node = node_list[i]; 1014 1015 if (node <= 0) 1016 continue; 1017 1018 bus = &i2c_bus[i]; 1019 bus->active = true; 1020 bus->is_highspeed = is_highspeed; 1021 1022 if (is_highspeed) { 1023 flags = PINMUX_FLAG_HS_MODE; 1024 bus->hsregs = (struct exynos5_hsi2c *) 1025 fdtdec_get_addr(blob, node, "reg"); 1026 } else { 1027 flags = 0; 1028 bus->regs = (struct s3c24x0_i2c *) 1029 fdtdec_get_addr(blob, node, "reg"); 1030 } 1031 1032 bus->id = pinmux_decode_periph_id(blob, node); 1033 bus->clock_frequency = fdtdec_get_int(blob, node, 1034 "clock-frequency", 1035 CONFIG_SYS_I2C_S3C24X0_SPEED); 1036 bus->node = node; 1037 bus->bus_num = i; 1038 exynos_pinmux_config(PERIPH_ID_I2C0 + bus->id, flags); 1039 1040 /* Mark position as used */ 1041 node_list[i] = -1; 1042 } 1043 } 1044 1045 void board_i2c_init(const void *blob) 1046 { 1047 int node_list[CONFIG_MAX_I2C_NUM]; 1048 int count; 1049 1050 /* First get the normal i2c ports */ 1051 count = fdtdec_find_aliases_for_id(blob, "i2c", 1052 COMPAT_SAMSUNG_S3C2440_I2C, node_list, 1053 CONFIG_MAX_I2C_NUM); 1054 process_nodes(blob, node_list, count, 0); 1055 1056 /* Now look for high speed i2c ports */ 1057 count = fdtdec_find_aliases_for_id(blob, "i2c", 1058 COMPAT_SAMSUNG_EXYNOS5_I2C, node_list, 1059 CONFIG_MAX_I2C_NUM); 1060 process_nodes(blob, node_list, count, 1); 1061 } 1062 1063 int i2c_get_bus_num_fdt(int node) 1064 { 1065 int i; 1066 1067 for (i = 0; i < ARRAY_SIZE(i2c_bus); i++) { 1068 if (node == i2c_bus[i].node) 1069 return i; 1070 } 1071 1072 debug("%s: Can't find any matched I2C bus\n", __func__); 1073 return -EINVAL; 1074 } 1075 1076 int i2c_reset_port_fdt(const void *blob, int node) 1077 { 1078 struct s3c24x0_i2c_bus *i2c_bus; 1079 int bus; 1080 1081 bus = i2c_get_bus_num_fdt(node); 1082 if (bus < 0) { 1083 debug("could not get bus for node %d\n", node); 1084 return bus; 1085 } 1086 1087 i2c_bus = get_bus(bus); 1088 if (!i2c_bus) { 1089 debug("get_bus() failed for node %d\n", node); 1090 return -EFAULT; 1091 } 1092 1093 if (i2c_bus->is_highspeed) { 1094 if (hsi2c_get_clk_details(i2c_bus)) 1095 return -EINVAL; 1096 hsi2c_ch_init(i2c_bus); 1097 } else { 1098 i2c_ch_init(i2c_bus->regs, i2c_bus->clock_frequency, 1099 CONFIG_SYS_I2C_S3C24X0_SLAVE); 1100 } 1101 1102 return 0; 1103 } 1104 #endif /* CONFIG_OF_CONTROL */ 1105 1106 #ifdef CONFIG_EXYNOS5 1107 static void exynos_i2c_init(struct i2c_adapter *adap, int speed, int slaveaddr) 1108 { 1109 /* This will override the speed selected in the fdt for that port */ 1110 debug("i2c_init(speed=%u, slaveaddr=0x%x)\n", speed, slaveaddr); 1111 if (i2c_set_bus_speed(speed)) 1112 error("i2c_init: failed to init bus for speed = %d", speed); 1113 } 1114 #endif /* CONFIG_EXYNOS5 */ 1115 1116 /* 1117 * Register s3c24x0 i2c adapters 1118 */ 1119 #if defined(CONFIG_EXYNOS5420) 1120 U_BOOT_I2C_ADAP_COMPLETE(i2c00, s3c24x0_i2c_init, s3c24x0_i2c_probe, 1121 s3c24x0_i2c_read, s3c24x0_i2c_write, 1122 s3c24x0_i2c_set_bus_speed, 1123 CONFIG_SYS_I2C_S3C24X0_SPEED, 1124 CONFIG_SYS_I2C_S3C24X0_SLAVE, 0) 1125 U_BOOT_I2C_ADAP_COMPLETE(i2c01, s3c24x0_i2c_init, s3c24x0_i2c_probe, 1126 s3c24x0_i2c_read, s3c24x0_i2c_write, 1127 s3c24x0_i2c_set_bus_speed, 1128 CONFIG_SYS_I2C_S3C24X0_SPEED, 1129 CONFIG_SYS_I2C_S3C24X0_SLAVE, 1) 1130 U_BOOT_I2C_ADAP_COMPLETE(i2c02, s3c24x0_i2c_init, s3c24x0_i2c_probe, 1131 s3c24x0_i2c_read, s3c24x0_i2c_write, 1132 s3c24x0_i2c_set_bus_speed, 1133 CONFIG_SYS_I2C_S3C24X0_SPEED, 1134 CONFIG_SYS_I2C_S3C24X0_SLAVE, 2) 1135 U_BOOT_I2C_ADAP_COMPLETE(i2c03, exynos_i2c_init, s3c24x0_i2c_probe, 1136 s3c24x0_i2c_read, s3c24x0_i2c_write, 1137 s3c24x0_i2c_set_bus_speed, 1138 CONFIG_SYS_I2C_S3C24X0_SPEED, 1139 CONFIG_SYS_I2C_S3C24X0_SLAVE, 3) 1140 U_BOOT_I2C_ADAP_COMPLETE(i2c04, exynos_i2c_init, s3c24x0_i2c_probe, 1141 s3c24x0_i2c_read, s3c24x0_i2c_write, 1142 s3c24x0_i2c_set_bus_speed, 1143 CONFIG_SYS_I2C_S3C24X0_SPEED, 1144 CONFIG_SYS_I2C_S3C24X0_SLAVE, 4) 1145 U_BOOT_I2C_ADAP_COMPLETE(i2c05, exynos_i2c_init, s3c24x0_i2c_probe, 1146 s3c24x0_i2c_read, s3c24x0_i2c_write, 1147 s3c24x0_i2c_set_bus_speed, 1148 CONFIG_SYS_I2C_S3C24X0_SPEED, 1149 CONFIG_SYS_I2C_S3C24X0_SLAVE, 5) 1150 U_BOOT_I2C_ADAP_COMPLETE(i2c06, exynos_i2c_init, s3c24x0_i2c_probe, 1151 s3c24x0_i2c_read, s3c24x0_i2c_write, 1152 s3c24x0_i2c_set_bus_speed, 1153 CONFIG_SYS_I2C_S3C24X0_SPEED, 1154 CONFIG_SYS_I2C_S3C24X0_SLAVE, 6) 1155 U_BOOT_I2C_ADAP_COMPLETE(i2c07, exynos_i2c_init, s3c24x0_i2c_probe, 1156 s3c24x0_i2c_read, s3c24x0_i2c_write, 1157 s3c24x0_i2c_set_bus_speed, 1158 CONFIG_SYS_I2C_S3C24X0_SPEED, 1159 CONFIG_SYS_I2C_S3C24X0_SLAVE, 7) 1160 U_BOOT_I2C_ADAP_COMPLETE(i2c08, exynos_i2c_init, s3c24x0_i2c_probe, 1161 s3c24x0_i2c_read, s3c24x0_i2c_write, 1162 s3c24x0_i2c_set_bus_speed, 1163 CONFIG_SYS_I2C_S3C24X0_SPEED, 1164 CONFIG_SYS_I2C_S3C24X0_SLAVE, 8) 1165 U_BOOT_I2C_ADAP_COMPLETE(i2c09, exynos_i2c_init, s3c24x0_i2c_probe, 1166 s3c24x0_i2c_read, s3c24x0_i2c_write, 1167 s3c24x0_i2c_set_bus_speed, 1168 CONFIG_SYS_I2C_S3C24X0_SPEED, 1169 CONFIG_SYS_I2C_S3C24X0_SLAVE, 9) 1170 U_BOOT_I2C_ADAP_COMPLETE(i2c10, exynos_i2c_init, s3c24x0_i2c_probe, 1171 s3c24x0_i2c_read, s3c24x0_i2c_write, 1172 s3c24x0_i2c_set_bus_speed, 1173 CONFIG_SYS_I2C_S3C24X0_SPEED, 1174 CONFIG_SYS_I2C_S3C24X0_SLAVE, 10) 1175 #elif defined(CONFIG_EXYNOS5250) 1176 U_BOOT_I2C_ADAP_COMPLETE(i2c00, exynos_i2c_init, s3c24x0_i2c_probe, 1177 s3c24x0_i2c_read, s3c24x0_i2c_write, 1178 s3c24x0_i2c_set_bus_speed, 1179 CONFIG_SYS_I2C_S3C24X0_SPEED, 1180 CONFIG_SYS_I2C_S3C24X0_SLAVE, 0) 1181 U_BOOT_I2C_ADAP_COMPLETE(i2c01, exynos_i2c_init, s3c24x0_i2c_probe, 1182 s3c24x0_i2c_read, s3c24x0_i2c_write, 1183 s3c24x0_i2c_set_bus_speed, 1184 CONFIG_SYS_I2C_S3C24X0_SPEED, 1185 CONFIG_SYS_I2C_S3C24X0_SLAVE, 1) 1186 U_BOOT_I2C_ADAP_COMPLETE(i2c02, exynos_i2c_init, s3c24x0_i2c_probe, 1187 s3c24x0_i2c_read, s3c24x0_i2c_write, 1188 s3c24x0_i2c_set_bus_speed, 1189 CONFIG_SYS_I2C_S3C24X0_SPEED, 1190 CONFIG_SYS_I2C_S3C24X0_SLAVE, 2) 1191 U_BOOT_I2C_ADAP_COMPLETE(i2c03, exynos_i2c_init, s3c24x0_i2c_probe, 1192 s3c24x0_i2c_read, s3c24x0_i2c_write, 1193 s3c24x0_i2c_set_bus_speed, 1194 CONFIG_SYS_I2C_S3C24X0_SPEED, 1195 CONFIG_SYS_I2C_S3C24X0_SLAVE, 3) 1196 U_BOOT_I2C_ADAP_COMPLETE(i2c04, s3c24x0_i2c_init, s3c24x0_i2c_probe, 1197 s3c24x0_i2c_read, s3c24x0_i2c_write, 1198 s3c24x0_i2c_set_bus_speed, 1199 CONFIG_SYS_I2C_S3C24X0_SPEED, 1200 CONFIG_SYS_I2C_S3C24X0_SLAVE, 4) 1201 U_BOOT_I2C_ADAP_COMPLETE(i2c05, s3c24x0_i2c_init, s3c24x0_i2c_probe, 1202 s3c24x0_i2c_read, s3c24x0_i2c_write, 1203 s3c24x0_i2c_set_bus_speed, 1204 CONFIG_SYS_I2C_S3C24X0_SPEED, 1205 CONFIG_SYS_I2C_S3C24X0_SLAVE, 5) 1206 U_BOOT_I2C_ADAP_COMPLETE(i2c06, s3c24x0_i2c_init, s3c24x0_i2c_probe, 1207 s3c24x0_i2c_read, s3c24x0_i2c_write, 1208 s3c24x0_i2c_set_bus_speed, 1209 CONFIG_SYS_I2C_S3C24X0_SPEED, 1210 CONFIG_SYS_I2C_S3C24X0_SLAVE, 6) 1211 U_BOOT_I2C_ADAP_COMPLETE(i2c07, s3c24x0_i2c_init, s3c24x0_i2c_probe, 1212 s3c24x0_i2c_read, s3c24x0_i2c_write, 1213 s3c24x0_i2c_set_bus_speed, 1214 CONFIG_SYS_I2C_S3C24X0_SPEED, 1215 CONFIG_SYS_I2C_S3C24X0_SLAVE, 7) 1216 U_BOOT_I2C_ADAP_COMPLETE(i2c08, s3c24x0_i2c_init, s3c24x0_i2c_probe, 1217 s3c24x0_i2c_read, s3c24x0_i2c_write, 1218 s3c24x0_i2c_set_bus_speed, 1219 CONFIG_SYS_I2C_S3C24X0_SPEED, 1220 CONFIG_SYS_I2C_S3C24X0_SLAVE, 8) 1221 U_BOOT_I2C_ADAP_COMPLETE(i2c09, s3c24x0_i2c_init, s3c24x0_i2c_probe, 1222 s3c24x0_i2c_read, s3c24x0_i2c_write, 1223 s3c24x0_i2c_set_bus_speed, 1224 CONFIG_SYS_I2C_S3C24X0_SPEED, 1225 CONFIG_SYS_I2C_S3C24X0_SLAVE, 9) 1226 U_BOOT_I2C_ADAP_COMPLETE(s3c10, s3c24x0_i2c_init, s3c24x0_i2c_probe, 1227 s3c24x0_i2c_read, s3c24x0_i2c_write, 1228 s3c24x0_i2c_set_bus_speed, 1229 CONFIG_SYS_I2C_S3C24X0_SPEED, 1230 CONFIG_SYS_I2C_S3C24X0_SLAVE, 10) 1231 #elif defined(CONFIG_EXYNOS4) 1232 U_BOOT_I2C_ADAP_COMPLETE(i2c00, s3c24x0_i2c_init, s3c24x0_i2c_probe, 1233 s3c24x0_i2c_read, s3c24x0_i2c_write, 1234 s3c24x0_i2c_set_bus_speed, 1235 CONFIG_SYS_I2C_S3C24X0_SPEED, 1236 CONFIG_SYS_I2C_S3C24X0_SLAVE, 0) 1237 U_BOOT_I2C_ADAP_COMPLETE(i2c01, s3c24x0_i2c_init, s3c24x0_i2c_probe, 1238 s3c24x0_i2c_read, s3c24x0_i2c_write, 1239 s3c24x0_i2c_set_bus_speed, 1240 CONFIG_SYS_I2C_S3C24X0_SPEED, 1241 CONFIG_SYS_I2C_S3C24X0_SLAVE, 1) 1242 U_BOOT_I2C_ADAP_COMPLETE(i2c02, s3c24x0_i2c_init, s3c24x0_i2c_probe, 1243 s3c24x0_i2c_read, s3c24x0_i2c_write, 1244 s3c24x0_i2c_set_bus_speed, 1245 CONFIG_SYS_I2C_S3C24X0_SPEED, 1246 CONFIG_SYS_I2C_S3C24X0_SLAVE, 2) 1247 U_BOOT_I2C_ADAP_COMPLETE(i2c03, s3c24x0_i2c_init, s3c24x0_i2c_probe, 1248 s3c24x0_i2c_read, s3c24x0_i2c_write, 1249 s3c24x0_i2c_set_bus_speed, 1250 CONFIG_SYS_I2C_S3C24X0_SPEED, 1251 CONFIG_SYS_I2C_S3C24X0_SLAVE, 3) 1252 U_BOOT_I2C_ADAP_COMPLETE(i2c04, s3c24x0_i2c_init, s3c24x0_i2c_probe, 1253 s3c24x0_i2c_read, s3c24x0_i2c_write, 1254 s3c24x0_i2c_set_bus_speed, 1255 CONFIG_SYS_I2C_S3C24X0_SPEED, 1256 CONFIG_SYS_I2C_S3C24X0_SLAVE, 4) 1257 U_BOOT_I2C_ADAP_COMPLETE(i2c05, s3c24x0_i2c_init, s3c24x0_i2c_probe, 1258 s3c24x0_i2c_read, s3c24x0_i2c_write, 1259 s3c24x0_i2c_set_bus_speed, 1260 CONFIG_SYS_I2C_S3C24X0_SPEED, 1261 CONFIG_SYS_I2C_S3C24X0_SLAVE, 5) 1262 U_BOOT_I2C_ADAP_COMPLETE(i2c06, s3c24x0_i2c_init, s3c24x0_i2c_probe, 1263 s3c24x0_i2c_read, s3c24x0_i2c_write, 1264 s3c24x0_i2c_set_bus_speed, 1265 CONFIG_SYS_I2C_S3C24X0_SPEED, 1266 CONFIG_SYS_I2C_S3C24X0_SLAVE, 6) 1267 U_BOOT_I2C_ADAP_COMPLETE(i2c07, s3c24x0_i2c_init, s3c24x0_i2c_probe, 1268 s3c24x0_i2c_read, s3c24x0_i2c_write, 1269 s3c24x0_i2c_set_bus_speed, 1270 CONFIG_SYS_I2C_S3C24X0_SPEED, 1271 CONFIG_SYS_I2C_S3C24X0_SLAVE, 7) 1272 U_BOOT_I2C_ADAP_COMPLETE(i2c08, s3c24x0_i2c_init, s3c24x0_i2c_probe, 1273 s3c24x0_i2c_read, s3c24x0_i2c_write, 1274 s3c24x0_i2c_set_bus_speed, 1275 CONFIG_SYS_I2C_S3C24X0_SPEED, 1276 CONFIG_SYS_I2C_S3C24X0_SLAVE, 8) 1277 #else 1278 U_BOOT_I2C_ADAP_COMPLETE(s3c0, s3c24x0_i2c_init, s3c24x0_i2c_probe, 1279 s3c24x0_i2c_read, s3c24x0_i2c_write, 1280 s3c24x0_i2c_set_bus_speed, 1281 CONFIG_SYS_I2C_S3C24X0_SPEED, 1282 CONFIG_SYS_I2C_S3C24X0_SLAVE, 0) 1283 #endif 1284 #endif /* CONFIG_SYS_I2C */ 1285 1286 #ifdef CONFIG_DM_I2C 1287 static int i2c_write_data(struct s3c24x0_i2c_bus *i2c_bus, uchar chip, 1288 uchar *buffer, int len, bool end_with_repeated_start) 1289 { 1290 int ret; 1291 1292 if (i2c_bus->is_highspeed) { 1293 ret = hsi2c_write(i2c_bus->hsregs, chip, 0, 0, 1294 buffer, len, true); 1295 if (ret) 1296 exynos5_i2c_reset(i2c_bus); 1297 } else { 1298 ret = i2c_transfer(i2c_bus->regs, I2C_WRITE, 1299 chip << 1, 0, 0, buffer, len); 1300 } 1301 1302 return ret != I2C_OK; 1303 } 1304 1305 static int i2c_read_data(struct s3c24x0_i2c_bus *i2c_bus, uchar chip, 1306 uchar *buffer, int len) 1307 { 1308 int ret; 1309 1310 if (i2c_bus->is_highspeed) { 1311 ret = hsi2c_read(i2c_bus->hsregs, chip, 0, 0, buffer, len); 1312 if (ret) 1313 exynos5_i2c_reset(i2c_bus); 1314 } else { 1315 ret = i2c_transfer(i2c_bus->regs, I2C_READ, 1316 chip << 1, 0, 0, buffer, len); 1317 } 1318 1319 return ret != I2C_OK; 1320 } 1321 1322 static int s3c24x0_i2c_xfer(struct udevice *dev, struct i2c_msg *msg, 1323 int nmsgs) 1324 { 1325 struct s3c24x0_i2c_bus *i2c_bus = dev_get_priv(dev); 1326 int ret; 1327 1328 for (; nmsgs > 0; nmsgs--, msg++) { 1329 bool next_is_read = nmsgs > 1 && (msg[1].flags & I2C_M_RD); 1330 1331 if (msg->flags & I2C_M_RD) { 1332 ret = i2c_read_data(i2c_bus, msg->addr, msg->buf, 1333 msg->len); 1334 } else { 1335 ret = i2c_write_data(i2c_bus, msg->addr, msg->buf, 1336 msg->len, next_is_read); 1337 } 1338 if (ret) 1339 return -EREMOTEIO; 1340 } 1341 1342 return 0; 1343 } 1344 1345 static int s3c_i2c_ofdata_to_platdata(struct udevice *dev) 1346 { 1347 const void *blob = gd->fdt_blob; 1348 struct s3c24x0_i2c_bus *i2c_bus = dev_get_priv(dev); 1349 int node, flags; 1350 1351 i2c_bus->is_highspeed = dev->of_id->data; 1352 node = dev->of_offset; 1353 1354 if (i2c_bus->is_highspeed) { 1355 flags = PINMUX_FLAG_HS_MODE; 1356 i2c_bus->hsregs = (struct exynos5_hsi2c *) 1357 fdtdec_get_addr(blob, node, "reg"); 1358 } else { 1359 flags = 0; 1360 i2c_bus->regs = (struct s3c24x0_i2c *) 1361 fdtdec_get_addr(blob, node, "reg"); 1362 } 1363 1364 i2c_bus->id = pinmux_decode_periph_id(blob, node); 1365 1366 i2c_bus->clock_frequency = fdtdec_get_int(blob, node, 1367 "clock-frequency", 1368 CONFIG_SYS_I2C_S3C24X0_SPEED); 1369 i2c_bus->node = node; 1370 i2c_bus->bus_num = dev->seq; 1371 1372 exynos_pinmux_config(i2c_bus->id, flags); 1373 1374 i2c_bus->active = true; 1375 1376 return 0; 1377 } 1378 1379 static const struct dm_i2c_ops s3c_i2c_ops = { 1380 .xfer = s3c24x0_i2c_xfer, 1381 .probe_chip = s3c24x0_i2c_probe, 1382 .set_bus_speed = s3c24x0_i2c_set_bus_speed, 1383 }; 1384 1385 static const struct udevice_id s3c_i2c_ids[] = { 1386 { .compatible = "samsung,s3c2440-i2c", .data = EXYNOS_I2C_STD }, 1387 { .compatible = "samsung,exynos5-hsi2c", .data = EXYNOS_I2C_HS }, 1388 { } 1389 }; 1390 1391 U_BOOT_DRIVER(i2c_s3c) = { 1392 .name = "i2c_s3c", 1393 .id = UCLASS_I2C, 1394 .of_match = s3c_i2c_ids, 1395 .ofdata_to_platdata = s3c_i2c_ofdata_to_platdata, 1396 .per_child_auto_alloc_size = sizeof(struct dm_i2c_chip), 1397 .priv_auto_alloc_size = sizeof(struct s3c24x0_i2c_bus), 1398 .ops = &s3c_i2c_ops, 1399 }; 1400 #endif /* CONFIG_DM_I2C */ 1401