1 /* 2 * (C) Copyright 2004-2010 3 * Texas Instruments, <www.ti.com> 4 * 5 * SPDX-License-Identifier: GPL-2.0+ 6 */ 7 #ifndef _OMAP2PLUS_I2C_H_ 8 #define _OMAP2PLUS_I2C_H_ 9 10 /* I2C masks */ 11 12 /* I2C Interrupt Enable Register (I2C_IE): */ 13 #define I2C_IE_GC_IE (1 << 5) 14 #define I2C_IE_XRDY_IE (1 << 4) /* Transmit data ready interrupt enable */ 15 #define I2C_IE_RRDY_IE (1 << 3) /* Receive data ready interrupt enable */ 16 #define I2C_IE_ARDY_IE (1 << 2) /* Register access ready interrupt enable */ 17 #define I2C_IE_NACK_IE (1 << 1) /* No acknowledgment interrupt enable */ 18 #define I2C_IE_AL_IE (1 << 0) /* Arbitration lost interrupt enable */ 19 20 /* I2C Status Register (I2C_STAT): */ 21 22 #define I2C_STAT_SBD (1 << 15) /* Single byte data */ 23 #define I2C_STAT_BB (1 << 12) /* Bus busy */ 24 #define I2C_STAT_ROVR (1 << 11) /* Receive overrun */ 25 #define I2C_STAT_XUDF (1 << 10) /* Transmit underflow */ 26 #define I2C_STAT_AAS (1 << 9) /* Address as slave */ 27 #define I2C_STAT_GC (1 << 5) 28 #define I2C_STAT_XRDY (1 << 4) /* Transmit data ready */ 29 #define I2C_STAT_RRDY (1 << 3) /* Receive data ready */ 30 #define I2C_STAT_ARDY (1 << 2) /* Register access ready */ 31 #define I2C_STAT_NACK (1 << 1) /* No acknowledgment interrupt enable */ 32 #define I2C_STAT_AL (1 << 0) /* Arbitration lost interrupt enable */ 33 34 /* I2C Interrupt Code Register (I2C_INTCODE): */ 35 36 #define I2C_INTCODE_MASK 7 37 #define I2C_INTCODE_NONE 0 38 #define I2C_INTCODE_AL 1 /* Arbitration lost */ 39 #define I2C_INTCODE_NAK 2 /* No acknowledgement/general call */ 40 #define I2C_INTCODE_ARDY 3 /* Register access ready */ 41 #define I2C_INTCODE_RRDY 4 /* Rcv data ready */ 42 #define I2C_INTCODE_XRDY 5 /* Xmit data ready */ 43 44 /* I2C Buffer Configuration Register (I2C_BUF): */ 45 46 #define I2C_BUF_RDMA_EN (1 << 15) /* Receive DMA channel enable */ 47 #define I2C_BUF_XDMA_EN (1 << 7) /* Transmit DMA channel enable */ 48 49 /* I2C Configuration Register (I2C_CON): */ 50 51 #define I2C_CON_EN (1 << 15) /* I2C module enable */ 52 #define I2C_CON_BE (1 << 14) /* Big endian mode */ 53 #define I2C_CON_STB (1 << 11) /* Start byte mode (master mode only) */ 54 #define I2C_CON_MST (1 << 10) /* Master/slave mode */ 55 #define I2C_CON_TRX (1 << 9) /* Transmitter/receiver mode */ 56 /* (master mode only) */ 57 #define I2C_CON_XA (1 << 8) /* Expand address */ 58 #define I2C_CON_STP (1 << 1) /* Stop condition (master mode only) */ 59 #define I2C_CON_STT (1 << 0) /* Start condition (master mode only) */ 60 61 /* I2C System Test Register (I2C_SYSTEST): */ 62 63 #define I2C_SYSTEST_ST_EN (1 << 15) /* System test enable */ 64 #define I2C_SYSTEST_FREE (1 << 14) /* Free running mode, on brkpoint) */ 65 #define I2C_SYSTEST_TMODE_MASK (3 << 12) /* Test mode select */ 66 #define I2C_SYSTEST_TMODE_SHIFT (12) /* Test mode select */ 67 #define I2C_SYSTEST_SCL_I (1 << 3) /* SCL line sense input value */ 68 #define I2C_SYSTEST_SCL_O (1 << 2) /* SCL line drive output value */ 69 #define I2C_SYSTEST_SDA_I (1 << 1) /* SDA line sense input value */ 70 #define I2C_SYSTEST_SDA_O (1 << 0) /* SDA line drive output value */ 71 72 /* I2C System Status Register (I2C_SYSS): */ 73 74 #define I2C_SYSS_RDONE (1 << 0) /* Internel reset monitoring */ 75 76 #define I2C_SCLL_SCLL 0 77 #define I2C_SCLL_SCLL_M 0xFF 78 #define I2C_SCLL_HSSCLL 8 79 #define I2C_SCLH_HSSCLL_M 0xFF 80 #define I2C_SCLH_SCLH 0 81 #define I2C_SCLH_SCLH_M 0xFF 82 #define I2C_SCLH_HSSCLH 8 83 #define I2C_SCLH_HSSCLH_M 0xFF 84 85 #define OMAP_I2C_STANDARD 100000 86 #define OMAP_I2C_FAST_MODE 400000 87 #define OMAP_I2C_HIGH_SPEED 3400000 88 89 #define SYSTEM_CLOCK_12 12000000 90 #define SYSTEM_CLOCK_13 13000000 91 #define SYSTEM_CLOCK_192 19200000 92 #define SYSTEM_CLOCK_96 96000000 93 94 /* Use the reference value of 96MHz if not explicitly set by the board */ 95 #ifndef I2C_IP_CLK 96 #define I2C_IP_CLK SYSTEM_CLOCK_96 97 #endif 98 99 /* 100 * The reference minimum clock for high speed is 19.2MHz. 101 * The linux 2.6.30 kernel uses this value. 102 * The reference minimum clock for fast mode is 9.6MHz 103 * The reference minimum clock for standard mode is 4MHz 104 * In TRM, the value of 12MHz is used. 105 */ 106 #ifndef I2C_INTERNAL_SAMPLING_CLK 107 #define I2C_INTERNAL_SAMPLING_CLK 19200000 108 #endif 109 110 /* 111 * The equation for the low and high time is 112 * tlow = scll + scll_trim = (sampling clock * tlow_duty) / speed 113 * thigh = sclh + sclh_trim = (sampling clock * (1 - tlow_duty)) / speed 114 * 115 * If the duty cycle is 50% 116 * 117 * tlow = scll + scll_trim = sampling clock / (2 * speed) 118 * thigh = sclh + sclh_trim = sampling clock / (2 * speed) 119 * 120 * In TRM 121 * scll_trim = 7 122 * sclh_trim = 5 123 * 124 * The linux 2.6.30 kernel uses 125 * scll_trim = 6 126 * sclh_trim = 6 127 * 128 * These are the trim values for standard and fast speed 129 */ 130 #ifndef I2C_FASTSPEED_SCLL_TRIM 131 #define I2C_FASTSPEED_SCLL_TRIM 6 132 #endif 133 #ifndef I2C_FASTSPEED_SCLH_TRIM 134 #define I2C_FASTSPEED_SCLH_TRIM 6 135 #endif 136 137 /* These are the trim values for high speed */ 138 #ifndef I2C_HIGHSPEED_PHASE_ONE_SCLL_TRIM 139 #define I2C_HIGHSPEED_PHASE_ONE_SCLL_TRIM I2C_FASTSPEED_SCLL_TRIM 140 #endif 141 #ifndef I2C_HIGHSPEED_PHASE_ONE_SCLH_TRIM 142 #define I2C_HIGHSPEED_PHASE_ONE_SCLH_TRIM I2C_FASTSPEED_SCLH_TRIM 143 #endif 144 #ifndef I2C_HIGHSPEED_PHASE_TWO_SCLL_TRIM 145 #define I2C_HIGHSPEED_PHASE_TWO_SCLL_TRIM I2C_FASTSPEED_SCLL_TRIM 146 #endif 147 #ifndef I2C_HIGHSPEED_PHASE_TWO_SCLH_TRIM 148 #define I2C_HIGHSPEED_PHASE_TWO_SCLH_TRIM I2C_FASTSPEED_SCLH_TRIM 149 #endif 150 151 #define I2C_PSC_MAX 0x0f 152 #define I2C_PSC_MIN 0x00 153 154 #endif /* _OMAP24XX_I2C_H_ */ 155