1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * Copyright 2013 Broadcom Corporation. 4 * 5 * NOTE: This driver should be converted to driver model before June 2017. 6 * Please see doc/driver-model/i2c-howto.txt for instructions. 7 */ 8 9 #include <common.h> 10 #include <asm/io.h> 11 #include <linux/errno.h> 12 #include <asm/arch/sysmap.h> 13 #include <asm/kona-common/clk.h> 14 #include <i2c.h> 15 16 /* Hardware register offsets and field defintions */ 17 #define CS_OFFSET 0x00000020 18 #define CS_ACK_SHIFT 3 19 #define CS_ACK_MASK 0x00000008 20 #define CS_ACK_CMD_GEN_START 0x00000000 21 #define CS_ACK_CMD_GEN_RESTART 0x00000001 22 #define CS_CMD_SHIFT 1 23 #define CS_CMD_CMD_NO_ACTION 0x00000000 24 #define CS_CMD_CMD_START_RESTART 0x00000001 25 #define CS_CMD_CMD_STOP 0x00000002 26 #define CS_EN_SHIFT 0 27 #define CS_EN_CMD_ENABLE_BSC 0x00000001 28 29 #define TIM_OFFSET 0x00000024 30 #define TIM_PRESCALE_SHIFT 6 31 #define TIM_P_SHIFT 3 32 #define TIM_NO_DIV_SHIFT 2 33 #define TIM_DIV_SHIFT 0 34 35 #define DAT_OFFSET 0x00000028 36 37 #define TOUT_OFFSET 0x0000002c 38 39 #define TXFCR_OFFSET 0x0000003c 40 #define TXFCR_FIFO_FLUSH_MASK 0x00000080 41 #define TXFCR_FIFO_EN_MASK 0x00000040 42 43 #define IER_OFFSET 0x00000044 44 #define IER_READ_COMPLETE_INT_MASK 0x00000010 45 #define IER_I2C_INT_EN_MASK 0x00000008 46 #define IER_FIFO_INT_EN_MASK 0x00000002 47 #define IER_NOACK_EN_MASK 0x00000001 48 49 #define ISR_OFFSET 0x00000048 50 #define ISR_RESERVED_MASK 0xffffff60 51 #define ISR_CMDBUSY_MASK 0x00000080 52 #define ISR_READ_COMPLETE_MASK 0x00000010 53 #define ISR_SES_DONE_MASK 0x00000008 54 #define ISR_ERR_MASK 0x00000004 55 #define ISR_TXFIFOEMPTY_MASK 0x00000002 56 #define ISR_NOACK_MASK 0x00000001 57 58 #define CLKEN_OFFSET 0x0000004c 59 #define CLKEN_AUTOSENSE_OFF_MASK 0x00000080 60 #define CLKEN_M_SHIFT 4 61 #define CLKEN_N_SHIFT 1 62 #define CLKEN_CLKEN_MASK 0x00000001 63 64 #define FIFO_STATUS_OFFSET 0x00000054 65 #define FIFO_STATUS_RXFIFO_EMPTY_MASK 0x00000004 66 #define FIFO_STATUS_TXFIFO_EMPTY_MASK 0x00000010 67 68 #define HSTIM_OFFSET 0x00000058 69 #define HSTIM_HS_MODE_MASK 0x00008000 70 #define HSTIM_HS_HOLD_SHIFT 10 71 #define HSTIM_HS_HIGH_PHASE_SHIFT 5 72 #define HSTIM_HS_SETUP_SHIFT 0 73 74 #define PADCTL_OFFSET 0x0000005c 75 #define PADCTL_PAD_OUT_EN_MASK 0x00000004 76 77 #define RXFCR_OFFSET 0x00000068 78 #define RXFCR_NACK_EN_SHIFT 7 79 #define RXFCR_READ_COUNT_SHIFT 0 80 #define RXFIFORDOUT_OFFSET 0x0000006c 81 82 /* Locally used constants */ 83 #define MAX_RX_FIFO_SIZE 64U /* bytes */ 84 #define MAX_TX_FIFO_SIZE 64U /* bytes */ 85 86 #define I2C_TIMEOUT 100000 /* usecs */ 87 88 #define WAIT_INT_CHK 100 /* usecs */ 89 #if I2C_TIMEOUT % WAIT_INT_CHK 90 #error I2C_TIMEOUT must be a multiple of WAIT_INT_CHK 91 #endif 92 93 /* Operations that can be commanded to the controller */ 94 enum bcm_kona_cmd_t { 95 BCM_CMD_NOACTION = 0, 96 BCM_CMD_START, 97 BCM_CMD_RESTART, 98 BCM_CMD_STOP, 99 }; 100 101 enum bus_speed_index { 102 BCM_SPD_100K = 0, 103 BCM_SPD_400K, 104 BCM_SPD_1MHZ, 105 }; 106 107 /* Internal divider settings for standard mode, fast mode and fast mode plus */ 108 struct bus_speed_cfg { 109 uint8_t time_m; /* Number of cycles for setup time */ 110 uint8_t time_n; /* Number of cycles for hold time */ 111 uint8_t prescale; /* Prescale divider */ 112 uint8_t time_p; /* Timing coefficient */ 113 uint8_t no_div; /* Disable clock divider */ 114 uint8_t time_div; /* Post-prescale divider */ 115 }; 116 117 static const struct bus_speed_cfg std_cfg_table[] = { 118 [BCM_SPD_100K] = {0x01, 0x01, 0x03, 0x06, 0x00, 0x02}, 119 [BCM_SPD_400K] = {0x05, 0x01, 0x03, 0x05, 0x01, 0x02}, 120 [BCM_SPD_1MHZ] = {0x01, 0x01, 0x03, 0x01, 0x01, 0x03}, 121 }; 122 123 struct bcm_kona_i2c_dev { 124 void *base; 125 uint speed; 126 const struct bus_speed_cfg *std_cfg; 127 }; 128 129 /* Keep these two defines in sync */ 130 #define DEF_SPD 100000 131 #define DEF_SPD_ENUM BCM_SPD_100K 132 133 #define DEF_DEVICE(num) \ 134 {(void *)CONFIG_SYS_I2C_BASE##num, DEF_SPD, &std_cfg_table[DEF_SPD_ENUM]} 135 136 static struct bcm_kona_i2c_dev g_i2c_devs[CONFIG_SYS_MAX_I2C_BUS] = { 137 #ifdef CONFIG_SYS_I2C_BASE0 138 DEF_DEVICE(0), 139 #endif 140 #ifdef CONFIG_SYS_I2C_BASE1 141 DEF_DEVICE(1), 142 #endif 143 #ifdef CONFIG_SYS_I2C_BASE2 144 DEF_DEVICE(2), 145 #endif 146 #ifdef CONFIG_SYS_I2C_BASE3 147 DEF_DEVICE(3), 148 #endif 149 #ifdef CONFIG_SYS_I2C_BASE4 150 DEF_DEVICE(4), 151 #endif 152 #ifdef CONFIG_SYS_I2C_BASE5 153 DEF_DEVICE(5), 154 #endif 155 }; 156 157 #define I2C_M_TEN 0x0010 /* ten bit address */ 158 #define I2C_M_RD 0x0001 /* read data */ 159 #define I2C_M_NOSTART 0x4000 /* no restart between msgs */ 160 161 struct kona_i2c_msg { 162 uint16_t addr; 163 uint16_t flags; 164 uint16_t len; 165 uint8_t *buf; 166 }; 167 168 static void bcm_kona_i2c_send_cmd_to_ctrl(struct bcm_kona_i2c_dev *dev, 169 enum bcm_kona_cmd_t cmd) 170 { 171 debug("%s, %d\n", __func__, cmd); 172 173 switch (cmd) { 174 case BCM_CMD_NOACTION: 175 writel((CS_CMD_CMD_NO_ACTION << CS_CMD_SHIFT) | 176 (CS_EN_CMD_ENABLE_BSC << CS_EN_SHIFT), 177 dev->base + CS_OFFSET); 178 break; 179 180 case BCM_CMD_START: 181 writel((CS_ACK_CMD_GEN_START << CS_ACK_SHIFT) | 182 (CS_CMD_CMD_START_RESTART << CS_CMD_SHIFT) | 183 (CS_EN_CMD_ENABLE_BSC << CS_EN_SHIFT), 184 dev->base + CS_OFFSET); 185 break; 186 187 case BCM_CMD_RESTART: 188 writel((CS_ACK_CMD_GEN_RESTART << CS_ACK_SHIFT) | 189 (CS_CMD_CMD_START_RESTART << CS_CMD_SHIFT) | 190 (CS_EN_CMD_ENABLE_BSC << CS_EN_SHIFT), 191 dev->base + CS_OFFSET); 192 break; 193 194 case BCM_CMD_STOP: 195 writel((CS_CMD_CMD_STOP << CS_CMD_SHIFT) | 196 (CS_EN_CMD_ENABLE_BSC << CS_EN_SHIFT), 197 dev->base + CS_OFFSET); 198 break; 199 200 default: 201 printf("Unknown command %d\n", cmd); 202 } 203 } 204 205 static void bcm_kona_i2c_enable_clock(struct bcm_kona_i2c_dev *dev) 206 { 207 writel(readl(dev->base + CLKEN_OFFSET) | CLKEN_CLKEN_MASK, 208 dev->base + CLKEN_OFFSET); 209 } 210 211 static void bcm_kona_i2c_disable_clock(struct bcm_kona_i2c_dev *dev) 212 { 213 writel(readl(dev->base + CLKEN_OFFSET) & ~CLKEN_CLKEN_MASK, 214 dev->base + CLKEN_OFFSET); 215 } 216 217 /* Wait until at least one of the mask bit(s) are set */ 218 static unsigned long wait_for_int_timeout(struct bcm_kona_i2c_dev *dev, 219 unsigned long time_left, 220 uint32_t mask) 221 { 222 uint32_t status; 223 224 while (time_left) { 225 status = readl(dev->base + ISR_OFFSET); 226 227 if ((status & ~ISR_RESERVED_MASK) == 0) { 228 debug("Bogus I2C interrupt 0x%x\n", status); 229 continue; 230 } 231 232 /* Must flush the TX FIFO when NAK detected */ 233 if (status & ISR_NOACK_MASK) 234 writel(TXFCR_FIFO_FLUSH_MASK | TXFCR_FIFO_EN_MASK, 235 dev->base + TXFCR_OFFSET); 236 237 writel(status & ~ISR_RESERVED_MASK, dev->base + ISR_OFFSET); 238 239 if (status & mask) { 240 /* We are done since one of the mask bits are set */ 241 return time_left; 242 } 243 udelay(WAIT_INT_CHK); 244 time_left -= WAIT_INT_CHK; 245 } 246 return 0; 247 } 248 249 /* Send command to I2C bus */ 250 static int bcm_kona_send_i2c_cmd(struct bcm_kona_i2c_dev *dev, 251 enum bcm_kona_cmd_t cmd) 252 { 253 int rc = 0; 254 unsigned long time_left = I2C_TIMEOUT; 255 256 /* Send the command */ 257 bcm_kona_i2c_send_cmd_to_ctrl(dev, cmd); 258 259 /* Wait for transaction to finish or timeout */ 260 time_left = wait_for_int_timeout(dev, time_left, IER_I2C_INT_EN_MASK); 261 262 if (!time_left) { 263 printf("controller timed out\n"); 264 rc = -ETIMEDOUT; 265 } 266 267 /* Clear command */ 268 bcm_kona_i2c_send_cmd_to_ctrl(dev, BCM_CMD_NOACTION); 269 270 return rc; 271 } 272 273 /* Read a single RX FIFO worth of data from the i2c bus */ 274 static int bcm_kona_i2c_read_fifo_single(struct bcm_kona_i2c_dev *dev, 275 uint8_t *buf, unsigned int len, 276 unsigned int last_byte_nak) 277 { 278 unsigned long time_left = I2C_TIMEOUT; 279 280 /* Start the RX FIFO */ 281 writel((last_byte_nak << RXFCR_NACK_EN_SHIFT) | 282 (len << RXFCR_READ_COUNT_SHIFT), dev->base + RXFCR_OFFSET); 283 284 /* Wait for FIFO read to complete */ 285 time_left = 286 wait_for_int_timeout(dev, time_left, IER_READ_COMPLETE_INT_MASK); 287 288 if (!time_left) { 289 printf("RX FIFO time out\n"); 290 return -EREMOTEIO; 291 } 292 293 /* Read data from FIFO */ 294 for (; len > 0; len--, buf++) 295 *buf = readl(dev->base + RXFIFORDOUT_OFFSET); 296 297 return 0; 298 } 299 300 /* Read any amount of data using the RX FIFO from the i2c bus */ 301 static int bcm_kona_i2c_read_fifo(struct bcm_kona_i2c_dev *dev, 302 struct kona_i2c_msg *msg) 303 { 304 unsigned int bytes_to_read = MAX_RX_FIFO_SIZE; 305 unsigned int last_byte_nak = 0; 306 unsigned int bytes_read = 0; 307 int rc; 308 309 uint8_t *tmp_buf = msg->buf; 310 311 while (bytes_read < msg->len) { 312 if (msg->len - bytes_read <= MAX_RX_FIFO_SIZE) { 313 last_byte_nak = 1; /* NAK last byte of transfer */ 314 bytes_to_read = msg->len - bytes_read; 315 } 316 317 rc = bcm_kona_i2c_read_fifo_single(dev, tmp_buf, bytes_to_read, 318 last_byte_nak); 319 if (rc < 0) 320 return -EREMOTEIO; 321 322 bytes_read += bytes_to_read; 323 tmp_buf += bytes_to_read; 324 } 325 326 return 0; 327 } 328 329 /* Write a single byte of data to the i2c bus */ 330 static int bcm_kona_i2c_write_byte(struct bcm_kona_i2c_dev *dev, uint8_t data, 331 unsigned int nak_expected) 332 { 333 unsigned long time_left = I2C_TIMEOUT; 334 unsigned int nak_received; 335 336 /* Clear pending session done interrupt */ 337 writel(ISR_SES_DONE_MASK, dev->base + ISR_OFFSET); 338 339 /* Send one byte of data */ 340 writel(data, dev->base + DAT_OFFSET); 341 342 time_left = wait_for_int_timeout(dev, time_left, IER_I2C_INT_EN_MASK); 343 344 if (!time_left) { 345 debug("controller timed out\n"); 346 return -ETIMEDOUT; 347 } 348 349 nak_received = readl(dev->base + CS_OFFSET) & CS_ACK_MASK ? 1 : 0; 350 351 if (nak_received ^ nak_expected) { 352 debug("unexpected NAK/ACK\n"); 353 return -EREMOTEIO; 354 } 355 356 return 0; 357 } 358 359 /* Write a single TX FIFO worth of data to the i2c bus */ 360 static int bcm_kona_i2c_write_fifo_single(struct bcm_kona_i2c_dev *dev, 361 uint8_t *buf, unsigned int len) 362 { 363 int k; 364 unsigned long time_left = I2C_TIMEOUT; 365 unsigned int fifo_status; 366 367 /* Write data into FIFO */ 368 for (k = 0; k < len; k++) 369 writel(buf[k], (dev->base + DAT_OFFSET)); 370 371 /* Wait for FIFO to empty */ 372 do { 373 time_left = 374 wait_for_int_timeout(dev, time_left, 375 (IER_FIFO_INT_EN_MASK | 376 IER_NOACK_EN_MASK)); 377 fifo_status = readl(dev->base + FIFO_STATUS_OFFSET); 378 } while (time_left && !(fifo_status & FIFO_STATUS_TXFIFO_EMPTY_MASK)); 379 380 /* Check if there was a NAK */ 381 if (readl(dev->base + CS_OFFSET) & CS_ACK_MASK) { 382 printf("unexpected NAK\n"); 383 return -EREMOTEIO; 384 } 385 386 /* Check if a timeout occurred */ 387 if (!time_left) { 388 printf("completion timed out\n"); 389 return -EREMOTEIO; 390 } 391 392 return 0; 393 } 394 395 /* Write any amount of data using TX FIFO to the i2c bus */ 396 static int bcm_kona_i2c_write_fifo(struct bcm_kona_i2c_dev *dev, 397 struct kona_i2c_msg *msg) 398 { 399 unsigned int bytes_to_write = MAX_TX_FIFO_SIZE; 400 unsigned int bytes_written = 0; 401 int rc; 402 403 uint8_t *tmp_buf = msg->buf; 404 405 while (bytes_written < msg->len) { 406 if (msg->len - bytes_written <= MAX_TX_FIFO_SIZE) 407 bytes_to_write = msg->len - bytes_written; 408 409 rc = bcm_kona_i2c_write_fifo_single(dev, tmp_buf, 410 bytes_to_write); 411 if (rc < 0) 412 return -EREMOTEIO; 413 414 bytes_written += bytes_to_write; 415 tmp_buf += bytes_to_write; 416 } 417 418 return 0; 419 } 420 421 /* Send i2c address */ 422 static int bcm_kona_i2c_do_addr(struct bcm_kona_i2c_dev *dev, 423 struct kona_i2c_msg *msg) 424 { 425 unsigned char addr; 426 427 if (msg->flags & I2C_M_TEN) { 428 /* First byte is 11110XX0 where XX is upper 2 bits */ 429 addr = 0xf0 | ((msg->addr & 0x300) >> 7); 430 if (bcm_kona_i2c_write_byte(dev, addr, 0) < 0) 431 return -EREMOTEIO; 432 433 /* Second byte is the remaining 8 bits */ 434 addr = msg->addr & 0xff; 435 if (bcm_kona_i2c_write_byte(dev, addr, 0) < 0) 436 return -EREMOTEIO; 437 438 if (msg->flags & I2C_M_RD) { 439 /* For read, send restart command */ 440 if (bcm_kona_send_i2c_cmd(dev, BCM_CMD_RESTART) < 0) 441 return -EREMOTEIO; 442 443 /* Then re-send the first byte with the read bit set */ 444 addr = 0xf0 | ((msg->addr & 0x300) >> 7) | 0x01; 445 if (bcm_kona_i2c_write_byte(dev, addr, 0) < 0) 446 return -EREMOTEIO; 447 } 448 } else { 449 addr = msg->addr << 1; 450 451 if (msg->flags & I2C_M_RD) 452 addr |= 1; 453 454 if (bcm_kona_i2c_write_byte(dev, addr, 0) < 0) 455 return -EREMOTEIO; 456 } 457 458 return 0; 459 } 460 461 static void bcm_kona_i2c_enable_autosense(struct bcm_kona_i2c_dev *dev) 462 { 463 writel(readl(dev->base + CLKEN_OFFSET) & ~CLKEN_AUTOSENSE_OFF_MASK, 464 dev->base + CLKEN_OFFSET); 465 } 466 467 static void bcm_kona_i2c_config_timing(struct bcm_kona_i2c_dev *dev) 468 { 469 writel(readl(dev->base + HSTIM_OFFSET) & ~HSTIM_HS_MODE_MASK, 470 dev->base + HSTIM_OFFSET); 471 472 writel((dev->std_cfg->prescale << TIM_PRESCALE_SHIFT) | 473 (dev->std_cfg->time_p << TIM_P_SHIFT) | 474 (dev->std_cfg->no_div << TIM_NO_DIV_SHIFT) | 475 (dev->std_cfg->time_div << TIM_DIV_SHIFT), 476 dev->base + TIM_OFFSET); 477 478 writel((dev->std_cfg->time_m << CLKEN_M_SHIFT) | 479 (dev->std_cfg->time_n << CLKEN_N_SHIFT) | 480 CLKEN_CLKEN_MASK, dev->base + CLKEN_OFFSET); 481 } 482 483 /* Master transfer function */ 484 static int bcm_kona_i2c_xfer(struct bcm_kona_i2c_dev *dev, 485 struct kona_i2c_msg msgs[], int num) 486 { 487 struct kona_i2c_msg *pmsg; 488 int rc = 0; 489 int i; 490 491 /* Enable pad output */ 492 writel(0, dev->base + PADCTL_OFFSET); 493 494 /* Enable internal clocks */ 495 bcm_kona_i2c_enable_clock(dev); 496 497 /* Send start command */ 498 rc = bcm_kona_send_i2c_cmd(dev, BCM_CMD_START); 499 if (rc < 0) { 500 printf("Start command failed rc = %d\n", rc); 501 goto xfer_disable_pad; 502 } 503 504 /* Loop through all messages */ 505 for (i = 0; i < num; i++) { 506 pmsg = &msgs[i]; 507 508 /* Send restart for subsequent messages */ 509 if ((i != 0) && ((pmsg->flags & I2C_M_NOSTART) == 0)) { 510 rc = bcm_kona_send_i2c_cmd(dev, BCM_CMD_RESTART); 511 if (rc < 0) { 512 printf("restart cmd failed rc = %d\n", rc); 513 goto xfer_send_stop; 514 } 515 } 516 517 /* Send slave address */ 518 if (!(pmsg->flags & I2C_M_NOSTART)) { 519 rc = bcm_kona_i2c_do_addr(dev, pmsg); 520 if (rc < 0) { 521 debug("NAK from addr %2.2x msg#%d rc = %d\n", 522 pmsg->addr, i, rc); 523 goto xfer_send_stop; 524 } 525 } 526 527 /* Perform data transfer */ 528 if (pmsg->flags & I2C_M_RD) { 529 rc = bcm_kona_i2c_read_fifo(dev, pmsg); 530 if (rc < 0) { 531 printf("read failure\n"); 532 goto xfer_send_stop; 533 } 534 } else { 535 rc = bcm_kona_i2c_write_fifo(dev, pmsg); 536 if (rc < 0) { 537 printf("write failure"); 538 goto xfer_send_stop; 539 } 540 } 541 } 542 543 rc = num; 544 545 xfer_send_stop: 546 /* Send a STOP command */ 547 bcm_kona_send_i2c_cmd(dev, BCM_CMD_STOP); 548 549 xfer_disable_pad: 550 /* Disable pad output */ 551 writel(PADCTL_PAD_OUT_EN_MASK, dev->base + PADCTL_OFFSET); 552 553 /* Stop internal clock */ 554 bcm_kona_i2c_disable_clock(dev); 555 556 return rc; 557 } 558 559 static uint bcm_kona_i2c_assign_bus_speed(struct bcm_kona_i2c_dev *dev, 560 uint speed) 561 { 562 switch (speed) { 563 case 100000: 564 dev->std_cfg = &std_cfg_table[BCM_SPD_100K]; 565 break; 566 case 400000: 567 dev->std_cfg = &std_cfg_table[BCM_SPD_400K]; 568 break; 569 case 1000000: 570 dev->std_cfg = &std_cfg_table[BCM_SPD_1MHZ]; 571 break; 572 default: 573 printf("%d hz bus speed not supported\n", speed); 574 return -EINVAL; 575 } 576 dev->speed = speed; 577 return 0; 578 } 579 580 static void bcm_kona_i2c_init(struct bcm_kona_i2c_dev *dev) 581 { 582 /* Parse bus speed */ 583 bcm_kona_i2c_assign_bus_speed(dev, dev->speed); 584 585 /* Enable internal clocks */ 586 bcm_kona_i2c_enable_clock(dev); 587 588 /* Configure internal dividers */ 589 bcm_kona_i2c_config_timing(dev); 590 591 /* Disable timeout */ 592 writel(0, dev->base + TOUT_OFFSET); 593 594 /* Enable autosense */ 595 bcm_kona_i2c_enable_autosense(dev); 596 597 /* Enable TX FIFO */ 598 writel(TXFCR_FIFO_FLUSH_MASK | TXFCR_FIFO_EN_MASK, 599 dev->base + TXFCR_OFFSET); 600 601 /* Mask all interrupts */ 602 writel(0, dev->base + IER_OFFSET); 603 604 /* Clear all pending interrupts */ 605 writel(ISR_CMDBUSY_MASK | 606 ISR_READ_COMPLETE_MASK | 607 ISR_SES_DONE_MASK | 608 ISR_ERR_MASK | 609 ISR_TXFIFOEMPTY_MASK | ISR_NOACK_MASK, dev->base + ISR_OFFSET); 610 611 /* Enable the controller but leave it idle */ 612 bcm_kona_i2c_send_cmd_to_ctrl(dev, BCM_CMD_NOACTION); 613 614 /* Disable pad output */ 615 writel(PADCTL_PAD_OUT_EN_MASK, dev->base + PADCTL_OFFSET); 616 } 617 618 /* 619 * uboot layer 620 */ 621 struct bcm_kona_i2c_dev *kona_get_dev(struct i2c_adapter *adap) 622 { 623 return &g_i2c_devs[adap->hwadapnr]; 624 } 625 626 static void kona_i2c_init(struct i2c_adapter *adap, int speed, int slaveaddr) 627 { 628 struct bcm_kona_i2c_dev *dev = kona_get_dev(adap); 629 630 if (clk_bsc_enable(dev->base)) 631 return; 632 633 bcm_kona_i2c_init(dev); 634 } 635 636 static int kona_i2c_read(struct i2c_adapter *adap, uchar chip, uint addr, 637 int alen, uchar *buffer, int len) 638 { 639 /* msg[0] writes the addr, msg[1] reads the data */ 640 struct kona_i2c_msg msg[2]; 641 unsigned char msgbuf0[64]; 642 struct bcm_kona_i2c_dev *dev = kona_get_dev(adap); 643 644 msg[0].addr = chip; 645 msg[0].flags = 0; 646 msg[0].len = 1; 647 msg[0].buf = msgbuf0; /* msgbuf0 contains incrementing reg addr */ 648 649 msg[1].addr = chip; 650 msg[1].flags = I2C_M_RD; 651 /* msg[1].buf dest ptr increments each read */ 652 653 msgbuf0[0] = (unsigned char)addr; 654 msg[1].buf = buffer; 655 msg[1].len = len; 656 if (bcm_kona_i2c_xfer(dev, msg, 2) < 0) { 657 /* Sending 2 i2c messages */ 658 kona_i2c_init(adap, adap->speed, adap->slaveaddr); 659 debug("I2C read: I/O error\n"); 660 return -EIO; 661 } 662 return 0; 663 } 664 665 static int kona_i2c_write(struct i2c_adapter *adap, uchar chip, uint addr, 666 int alen, uchar *buffer, int len) 667 { 668 struct kona_i2c_msg msg[1]; 669 unsigned char msgbuf0[64]; 670 unsigned int i; 671 struct bcm_kona_i2c_dev *dev = kona_get_dev(adap); 672 673 msg[0].addr = chip; 674 msg[0].flags = 0; 675 msg[0].len = 2; /* addr byte plus data */ 676 msg[0].buf = msgbuf0; 677 678 for (i = 0; i < len; i++) { 679 msgbuf0[0] = addr++; 680 msgbuf0[1] = buffer[i]; 681 if (bcm_kona_i2c_xfer(dev, msg, 1) < 0) { 682 kona_i2c_init(adap, adap->speed, adap->slaveaddr); 683 debug("I2C write: I/O error\n"); 684 return -EIO; 685 } 686 } 687 return 0; 688 } 689 690 static int kona_i2c_probe(struct i2c_adapter *adap, uchar chip) 691 { 692 uchar tmp; 693 694 /* 695 * read addr 0x0 of the given chip. 696 */ 697 return kona_i2c_read(adap, chip, 0x0, 1, &tmp, 1); 698 } 699 700 static uint kona_i2c_set_bus_speed(struct i2c_adapter *adap, uint speed) 701 { 702 struct bcm_kona_i2c_dev *dev = kona_get_dev(adap); 703 return bcm_kona_i2c_assign_bus_speed(dev, speed); 704 } 705 706 /* 707 * Register kona i2c adapters. Keep the order below so 708 * that the bus number matches the adapter number. 709 */ 710 #define DEF_ADAPTER(num) \ 711 U_BOOT_I2C_ADAP_COMPLETE(kona##num, kona_i2c_init, kona_i2c_probe, \ 712 kona_i2c_read, kona_i2c_write, \ 713 kona_i2c_set_bus_speed, DEF_SPD, 0x00, num) 714 715 #ifdef CONFIG_SYS_I2C_BASE0 716 DEF_ADAPTER(0) 717 #endif 718 #ifdef CONFIG_SYS_I2C_BASE1 719 DEF_ADAPTER(1) 720 #endif 721 #ifdef CONFIG_SYS_I2C_BASE2 722 DEF_ADAPTER(2) 723 #endif 724 #ifdef CONFIG_SYS_I2C_BASE3 725 DEF_ADAPTER(3) 726 #endif 727 #ifdef CONFIG_SYS_I2C_BASE4 728 DEF_ADAPTER(4) 729 #endif 730 #ifdef CONFIG_SYS_I2C_BASE5 731 DEF_ADAPTER(5) 732 #endif 733