1 /* 2 * Copyright 2006,2009 Freescale Semiconductor, Inc. 3 * 4 * This program is free software; you can redistribute it and/or 5 * modify it under the terms of the GNU General Public License 6 * Version 2 as published by the Free Software Foundation. 7 * 8 * This program is distributed in the hope that it will be useful, 9 * but WITHOUT ANY WARRANTY; without even the implied warranty of 10 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 11 * GNU General Public License for more details. 12 * 13 * You should have received a copy of the GNU General Public License 14 * along with this program; if not, write to the Free Software 15 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, 16 * MA 02111-1307 USA 17 */ 18 19 #include <common.h> 20 21 #ifdef CONFIG_HARD_I2C 22 23 #include <command.h> 24 #include <i2c.h> /* Functional interface */ 25 26 #include <asm/io.h> 27 #include <asm/fsl_i2c.h> /* HW definitions */ 28 29 /* The maximum number of microseconds we will wait until another master has 30 * released the bus. If not defined in the board header file, then use a 31 * generic value. 32 */ 33 #ifndef CONFIG_I2C_MBB_TIMEOUT 34 #define CONFIG_I2C_MBB_TIMEOUT 100000 35 #endif 36 37 /* The maximum number of microseconds we will wait for a read or write 38 * operation to complete. If not defined in the board header file, then use a 39 * generic value. 40 */ 41 #ifndef CONFIG_I2C_TIMEOUT 42 #define CONFIG_I2C_TIMEOUT 10000 43 #endif 44 45 #define I2C_READ_BIT 1 46 #define I2C_WRITE_BIT 0 47 48 DECLARE_GLOBAL_DATA_PTR; 49 50 /* Initialize the bus pointer to whatever one the SPD EEPROM is on. 51 * Default is bus 0. This is necessary because the DDR initialization 52 * runs from ROM, and we can't switch buses because we can't modify 53 * the global variables. 54 */ 55 #ifndef CONFIG_SYS_SPD_BUS_NUM 56 #define CONFIG_SYS_SPD_BUS_NUM 0 57 #endif 58 static unsigned int i2c_bus_num __attribute__ ((section (".data"))) = CONFIG_SYS_SPD_BUS_NUM; 59 #if defined(CONFIG_I2C_MUX) 60 static unsigned int i2c_bus_num_mux __attribute__ ((section ("data"))) = 0; 61 #endif 62 63 static unsigned int i2c_bus_speed[2] = {CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SPEED}; 64 65 static const struct fsl_i2c *i2c_dev[2] = { 66 (struct fsl_i2c *) (CONFIG_SYS_IMMR + CONFIG_SYS_I2C_OFFSET), 67 #ifdef CONFIG_SYS_I2C2_OFFSET 68 (struct fsl_i2c *) (CONFIG_SYS_IMMR + CONFIG_SYS_I2C2_OFFSET) 69 #endif 70 }; 71 72 /* I2C speed map for a DFSR value of 1 */ 73 74 /* 75 * Map I2C frequency dividers to FDR and DFSR values 76 * 77 * This structure is used to define the elements of a table that maps I2C 78 * frequency divider (I2C clock rate divided by I2C bus speed) to a value to be 79 * programmed into the Frequency Divider Ratio (FDR) and Digital Filter 80 * Sampling Rate (DFSR) registers. 81 * 82 * The actual table should be defined in the board file, and it must be called 83 * fsl_i2c_speed_map[]. 84 * 85 * The last entry of the table must have a value of {-1, X}, where X is same 86 * FDR/DFSR values as the second-to-last entry. This guarantees that any 87 * search through the array will always find a match. 88 * 89 * The values of the divider must be in increasing numerical order, i.e. 90 * fsl_i2c_speed_map[x+1].divider > fsl_i2c_speed_map[x].divider. 91 * 92 * For this table, the values are based on a value of 1 for the DFSR 93 * register. See the application note AN2919 "Determining the I2C Frequency 94 * Divider Ratio for SCL" 95 * 96 * ColdFire I2C frequency dividers for FDR values are different from 97 * PowerPC. The protocol to use the I2C module is still the same. 98 * A different table is defined and are based on MCF5xxx user manual. 99 * 100 */ 101 static const struct { 102 unsigned short divider; 103 u8 fdr; 104 } fsl_i2c_speed_map[] = { 105 #ifdef __M68K__ 106 {20, 32}, {22, 33}, {24, 34}, {26, 35}, 107 {28, 0}, {28, 36}, {30, 1}, {32, 37}, 108 {34, 2}, {36, 38}, {40, 3}, {40, 39}, 109 {44, 4}, {48, 5}, {48, 40}, {56, 6}, 110 {56, 41}, {64, 42}, {68, 7}, {72, 43}, 111 {80, 8}, {80, 44}, {88, 9}, {96, 41}, 112 {104, 10}, {112, 42}, {128, 11}, {128, 43}, 113 {144, 12}, {160, 13}, {160, 48}, {192, 14}, 114 {192, 49}, {224, 50}, {240, 15}, {256, 51}, 115 {288, 16}, {320, 17}, {320, 52}, {384, 18}, 116 {384, 53}, {448, 54}, {480, 19}, {512, 55}, 117 {576, 20}, {640, 21}, {640, 56}, {768, 22}, 118 {768, 57}, {960, 23}, {896, 58}, {1024, 59}, 119 {1152, 24}, {1280, 25}, {1280, 60}, {1536, 26}, 120 {1536, 61}, {1792, 62}, {1920, 27}, {2048, 63}, 121 {2304, 28}, {2560, 29}, {3072, 30}, {3840, 31}, 122 {-1, 31} 123 #endif 124 }; 125 126 /** 127 * Set the I2C bus speed for a given I2C device 128 * 129 * @param dev: the I2C device 130 * @i2c_clk: I2C bus clock frequency 131 * @speed: the desired speed of the bus 132 * 133 * The I2C device must be stopped before calling this function. 134 * 135 * The return value is the actual bus speed that is set. 136 */ 137 static unsigned int set_i2c_bus_speed(const struct fsl_i2c *dev, 138 unsigned int i2c_clk, unsigned int speed) 139 { 140 unsigned short divider = min(i2c_clk / speed, (unsigned short) -1); 141 142 /* 143 * We want to choose an FDR/DFSR that generates an I2C bus speed that 144 * is equal to or lower than the requested speed. That means that we 145 * want the first divider that is equal to or greater than the 146 * calculated divider. 147 */ 148 #ifdef __PPC__ 149 u8 dfsr, fdr = 0x31; /* Default if no FDR found */ 150 /* a, b and dfsr matches identifiers A,B and C respectively in AN2919 */ 151 unsigned short a, b, ga, gb; 152 unsigned long c_div, est_div; 153 154 #ifdef CONFIG_FSL_I2C_CUSTOM_DFSR 155 dfsr = CONFIG_FSL_I2C_CUSTOM_DFSR; 156 #else 157 /* Condition 1: dfsr <= 50/T */ 158 dfsr = (5 * (i2c_clk / 1000)) / 100000; 159 #endif 160 #ifdef CONFIG_FSL_I2C_CUSTOM_FDR 161 fdr = CONFIG_FSL_I2C_CUSTOM_FDR; 162 speed = i2c_clk / divider; /* Fake something */ 163 #else 164 debug("Requested speed:%d, i2c_clk:%d\n", speed, i2c_clk); 165 if (!dfsr) 166 dfsr = 1; 167 168 est_div = ~0; 169 for (ga = 0x4, a = 10; a <= 30; ga++, a += 2) { 170 for (gb = 0; gb < 8; gb++) { 171 b = 16 << gb; 172 c_div = b * (a + ((3*dfsr)/b)*2); 173 if ((c_div > divider) && (c_div < est_div)) { 174 unsigned short bin_gb, bin_ga; 175 176 est_div = c_div; 177 bin_gb = gb << 2; 178 bin_ga = (ga & 0x3) | ((ga & 0x4) << 3); 179 fdr = bin_gb | bin_ga; 180 speed = i2c_clk / est_div; 181 debug("FDR:0x%.2x, div:%ld, ga:0x%x, gb:0x%x, " 182 "a:%d, b:%d, speed:%d\n", 183 fdr, est_div, ga, gb, a, b, speed); 184 /* Condition 2 not accounted for */ 185 debug("Tr <= %d ns\n", 186 (b - 3 * dfsr) * 1000000 / 187 (i2c_clk / 1000)); 188 } 189 } 190 if (a == 20) 191 a += 2; 192 if (a == 24) 193 a += 4; 194 } 195 debug("divider:%d, est_div:%ld, DFSR:%d\n", divider, est_div, dfsr); 196 debug("FDR:0x%.2x, speed:%d\n", fdr, speed); 197 #endif 198 writeb(dfsr, &dev->dfsrr); /* set default filter */ 199 writeb(fdr, &dev->fdr); /* set bus speed */ 200 #else 201 unsigned int i; 202 203 for (i = 0; i < ARRAY_SIZE(fsl_i2c_speed_map); i++) 204 if (fsl_i2c_speed_map[i].divider >= divider) { 205 u8 fdr; 206 207 fdr = fsl_i2c_speed_map[i].fdr; 208 speed = i2c_clk / fsl_i2c_speed_map[i].divider; 209 writeb(fdr, &dev->fdr); /* set bus speed */ 210 211 break; 212 } 213 #endif 214 return speed; 215 } 216 217 static unsigned int get_i2c_clock(int bus) 218 { 219 if (bus) 220 return gd->arch.i2c2_clk; /* I2C2 clock */ 221 else 222 return gd->arch.i2c1_clk; /* I2C1 clock */ 223 } 224 225 void 226 i2c_init(int speed, int slaveadd) 227 { 228 const struct fsl_i2c *dev; 229 unsigned int temp; 230 int bus_num, i; 231 232 #ifdef CONFIG_SYS_I2C_INIT_BOARD 233 /* Call board specific i2c bus reset routine before accessing the 234 * environment, which might be in a chip on that bus. For details 235 * about this problem see doc/I2C_Edge_Conditions. 236 */ 237 i2c_init_board(); 238 #endif 239 #ifdef CONFIG_SYS_I2C2_OFFSET 240 bus_num = 2; 241 #else 242 bus_num = 1; 243 #endif 244 for (i = 0; i < bus_num; i++) { 245 dev = i2c_dev[i]; 246 247 writeb(0, &dev->cr); /* stop I2C controller */ 248 udelay(5); /* let it shutdown in peace */ 249 temp = set_i2c_bus_speed(dev, get_i2c_clock(i), speed); 250 if (gd->flags & GD_FLG_RELOC) 251 i2c_bus_speed[i] = temp; 252 writeb(slaveadd << 1, &dev->adr);/* write slave address */ 253 writeb(0x0, &dev->sr); /* clear status register */ 254 writeb(I2C_CR_MEN, &dev->cr); /* start I2C controller */ 255 } 256 257 #ifdef CONFIG_SYS_I2C_BOARD_LATE_INIT 258 /* Call board specific i2c bus reset routine AFTER the bus has been 259 * initialized. Use either this callpoint or i2c_init_board; 260 * which is called before i2c_init operations. 261 * For details about this problem see doc/I2C_Edge_Conditions. 262 */ 263 i2c_board_late_init(); 264 #endif 265 } 266 267 static int 268 i2c_wait4bus(void) 269 { 270 unsigned long long timeval = get_ticks(); 271 const unsigned long long timeout = usec2ticks(CONFIG_I2C_MBB_TIMEOUT); 272 273 while (readb(&i2c_dev[i2c_bus_num]->sr) & I2C_SR_MBB) { 274 if ((get_ticks() - timeval) > timeout) 275 return -1; 276 } 277 278 return 0; 279 } 280 281 static __inline__ int 282 i2c_wait(int write) 283 { 284 u32 csr; 285 unsigned long long timeval = get_ticks(); 286 const unsigned long long timeout = usec2ticks(CONFIG_I2C_TIMEOUT); 287 288 do { 289 csr = readb(&i2c_dev[i2c_bus_num]->sr); 290 if (!(csr & I2C_SR_MIF)) 291 continue; 292 /* Read again to allow register to stabilise */ 293 csr = readb(&i2c_dev[i2c_bus_num]->sr); 294 295 writeb(0x0, &i2c_dev[i2c_bus_num]->sr); 296 297 if (csr & I2C_SR_MAL) { 298 debug("i2c_wait: MAL\n"); 299 return -1; 300 } 301 302 if (!(csr & I2C_SR_MCF)) { 303 debug("i2c_wait: unfinished\n"); 304 return -1; 305 } 306 307 if (write == I2C_WRITE_BIT && (csr & I2C_SR_RXAK)) { 308 debug("i2c_wait: No RXACK\n"); 309 return -1; 310 } 311 312 return 0; 313 } while ((get_ticks() - timeval) < timeout); 314 315 debug("i2c_wait: timed out\n"); 316 return -1; 317 } 318 319 static __inline__ int 320 i2c_write_addr (u8 dev, u8 dir, int rsta) 321 { 322 writeb(I2C_CR_MEN | I2C_CR_MSTA | I2C_CR_MTX 323 | (rsta ? I2C_CR_RSTA : 0), 324 &i2c_dev[i2c_bus_num]->cr); 325 326 writeb((dev << 1) | dir, &i2c_dev[i2c_bus_num]->dr); 327 328 if (i2c_wait(I2C_WRITE_BIT) < 0) 329 return 0; 330 331 return 1; 332 } 333 334 static __inline__ int 335 __i2c_write(u8 *data, int length) 336 { 337 int i; 338 339 for (i = 0; i < length; i++) { 340 writeb(data[i], &i2c_dev[i2c_bus_num]->dr); 341 342 if (i2c_wait(I2C_WRITE_BIT) < 0) 343 break; 344 } 345 346 return i; 347 } 348 349 static __inline__ int 350 __i2c_read(u8 *data, int length) 351 { 352 int i; 353 354 writeb(I2C_CR_MEN | I2C_CR_MSTA | ((length == 1) ? I2C_CR_TXAK : 0), 355 &i2c_dev[i2c_bus_num]->cr); 356 357 /* dummy read */ 358 readb(&i2c_dev[i2c_bus_num]->dr); 359 360 for (i = 0; i < length; i++) { 361 if (i2c_wait(I2C_READ_BIT) < 0) 362 break; 363 364 /* Generate ack on last next to last byte */ 365 if (i == length - 2) 366 writeb(I2C_CR_MEN | I2C_CR_MSTA | I2C_CR_TXAK, 367 &i2c_dev[i2c_bus_num]->cr); 368 369 /* Do not generate stop on last byte */ 370 if (i == length - 1) 371 writeb(I2C_CR_MEN | I2C_CR_MSTA | I2C_CR_MTX, 372 &i2c_dev[i2c_bus_num]->cr); 373 374 data[i] = readb(&i2c_dev[i2c_bus_num]->dr); 375 } 376 377 return i; 378 } 379 380 int 381 i2c_read(u8 dev, uint addr, int alen, u8 *data, int length) 382 { 383 int i = -1; /* signal error */ 384 u8 *a = (u8*)&addr; 385 386 if (i2c_wait4bus() >= 0 387 && i2c_write_addr(dev, I2C_WRITE_BIT, 0) != 0 388 && __i2c_write(&a[4 - alen], alen) == alen) 389 i = 0; /* No error so far */ 390 391 if (length 392 && i2c_write_addr(dev, I2C_READ_BIT, 1) != 0) 393 i = __i2c_read(data, length); 394 395 writeb(I2C_CR_MEN, &i2c_dev[i2c_bus_num]->cr); 396 397 if (i2c_wait4bus()) /* Wait until STOP */ 398 debug("i2c_read: wait4bus timed out\n"); 399 400 if (i == length) 401 return 0; 402 403 return -1; 404 } 405 406 int 407 i2c_write(u8 dev, uint addr, int alen, u8 *data, int length) 408 { 409 int i = -1; /* signal error */ 410 u8 *a = (u8*)&addr; 411 412 if (i2c_wait4bus() >= 0 413 && i2c_write_addr(dev, I2C_WRITE_BIT, 0) != 0 414 && __i2c_write(&a[4 - alen], alen) == alen) { 415 i = __i2c_write(data, length); 416 } 417 418 writeb(I2C_CR_MEN, &i2c_dev[i2c_bus_num]->cr); 419 if (i2c_wait4bus()) /* Wait until STOP */ 420 debug("i2c_write: wait4bus timed out\n"); 421 422 if (i == length) 423 return 0; 424 425 return -1; 426 } 427 428 int 429 i2c_probe(uchar chip) 430 { 431 /* For unknow reason the controller will ACK when 432 * probing for a slave with the same address, so skip 433 * it. 434 */ 435 if (chip == (readb(&i2c_dev[i2c_bus_num]->adr) >> 1)) 436 return -1; 437 438 return i2c_read(chip, 0, 0, NULL, 0); 439 } 440 441 int i2c_set_bus_num(unsigned int bus) 442 { 443 #if defined(CONFIG_I2C_MUX) 444 if (bus < CONFIG_SYS_MAX_I2C_BUS) { 445 i2c_bus_num = bus; 446 } else { 447 int ret; 448 449 ret = i2x_mux_select_mux(bus); 450 if (ret) 451 return ret; 452 i2c_bus_num = 0; 453 } 454 i2c_bus_num_mux = bus; 455 #else 456 #ifdef CONFIG_SYS_I2C2_OFFSET 457 if (bus > 1) { 458 #else 459 if (bus > 0) { 460 #endif 461 return -1; 462 } 463 464 i2c_bus_num = bus; 465 #endif 466 return 0; 467 } 468 469 int i2c_set_bus_speed(unsigned int speed) 470 { 471 unsigned int i2c_clk = (i2c_bus_num == 1) 472 ? gd->arch.i2c2_clk : gd->arch.i2c1_clk; 473 474 writeb(0, &i2c_dev[i2c_bus_num]->cr); /* stop controller */ 475 i2c_bus_speed[i2c_bus_num] = 476 set_i2c_bus_speed(i2c_dev[i2c_bus_num], i2c_clk, speed); 477 writeb(I2C_CR_MEN, &i2c_dev[i2c_bus_num]->cr); /* start controller */ 478 479 return 0; 480 } 481 482 unsigned int i2c_get_bus_num(void) 483 { 484 #if defined(CONFIG_I2C_MUX) 485 return i2c_bus_num_mux; 486 #else 487 return i2c_bus_num; 488 #endif 489 } 490 491 unsigned int i2c_get_bus_speed(void) 492 { 493 return i2c_bus_speed[i2c_bus_num]; 494 } 495 496 #endif /* CONFIG_HARD_I2C */ 497