xref: /openbmc/u-boot/drivers/i2c/Kconfig (revision 310ae37e)
1#
2# I2C subsystem configuration
3#
4
5menu "I2C support"
6
7config DM_I2C
8	bool "Enable Driver Model for I2C drivers"
9	depends on DM
10	help
11	  Enable driver model for I2C. The I2C uclass interface: probe, read,
12	  write and speed, is implemented with the bus drivers operations,
13	  which provide methods for bus setting and data transfer. Each chip
14	  device (bus child) info is kept as parent platdata. The interface
15	  is defined in include/i2c.h. When i2c bus driver supports the i2c
16	  uclass, but the device drivers not, then DM_I2C_COMPAT config can
17	  be used as compatibility layer.
18
19config DM_I2C_COMPAT
20	bool "Enable I2C compatibility layer"
21	depends on DM
22	help
23	  Enable old-style I2C functions for compatibility with existing code.
24	  This option can be enabled as a temporary measure to avoid needing
25	  to convert all code for a board in a single commit. It should not
26	  be enabled for any board in an official release.
27
28config I2C_CROS_EC_TUNNEL
29	tristate "Chrome OS EC tunnel I2C bus"
30	depends on CROS_EC
31	help
32	  This provides an I2C bus that will tunnel i2c commands through to
33	  the other side of the Chrome OS EC to the I2C bus connected there.
34	  This will work whatever the interface used to talk to the EC (SPI,
35	  I2C or LPC). Some Chromebooks use this when the hardware design
36	  does not allow direct access to the main PMIC from the AP.
37
38config I2C_CROS_EC_LDO
39	bool "Provide access to LDOs on the Chrome OS EC"
40	depends on CROS_EC
41	---help---
42	On many Chromebooks the main PMIC is inaccessible to the AP. This is
43	often dealt with by using an I2C pass-through interface provided by
44	the EC. On some unfortunate models (e.g. Spring) the pass-through
45	is not available, and an LDO message is available instead. This
46	option enables a driver which provides very basic access to those
47	regulators, via the EC. We implement this as an I2C bus	which
48	emulates just the TPS65090 messages we know about. This is done to
49	avoid duplicating the logic in the TPS65090 regulator driver for
50	enabling/disabling an LDO.
51
52config DM_I2C_GPIO
53	bool "Enable Driver Model for software emulated I2C bus driver"
54	depends on DM_I2C && DM_GPIO
55	help
56	  Enable the i2c bus driver emulation by using the GPIOs. The bus GPIO
57	  configuration is given by the device tree. Kernel-style device tree
58	  bindings are supported.
59	  Binding info: doc/device-tree-bindings/i2c/i2c-gpio.txt
60
61config SYS_I2C_ROCKCHIP
62	bool "Rockchip I2C driver"
63	depends on DM_I2C
64	help
65	  Add support for the Rockchip I2C driver. This is used with various
66	  Rockchip parts such as RK3126, RK3128, RK3036 and RK3288. All chips
67	  have several I2C ports and all are provided, controled by the
68	  device tree.
69
70config SYS_I2C_SANDBOX
71	bool "Sandbox I2C driver"
72	depends on SANDBOX && DM_I2C
73	help
74	  Enable I2C support for sandbox. This is an emulation of a real I2C
75	  bus. Devices can be attached to the bus using the device tree
76	  which specifies the driver to use. As an example, see this device
77	  tree fragment from sandbox.dts. It shows that the I2C bus has a
78	  single EEPROM at address 0x2c (7-bit address) which is emulated by
79	  the driver for "sandbox,i2c-eeprom", which is in
80	  drivers/misc/i2c_eeprom_emul.c.
81
82	  i2c@0 {
83		#address-cells = <1>;
84		#size-cells = <0>;
85		reg = <0>;
86		compatible = "sandbox,i2c";
87		clock-frequency = <400000>;
88		eeprom@2c {
89			reg = <0x2c>;
90			compatible = "i2c-eeprom";
91			emul {
92				compatible = "sandbox,i2c-eeprom";
93				sandbox,filename = "i2c.bin";
94				sandbox,size = <128>;
95			};
96		};
97	};
98
99
100config SYS_I2C_UNIPHIER
101	bool "UniPhier I2C driver"
102	depends on ARCH_UNIPHIER && DM_I2C
103	default y
104	help
105	  Support for UniPhier I2C controller driver.  This I2C controller
106	  is used on PH1-LD4, PH1-sLD8 or older UniPhier SoCs.
107
108config SYS_I2C_UNIPHIER_F
109	bool "UniPhier FIFO-builtin I2C driver"
110	depends on ARCH_UNIPHIER && DM_I2C
111	default y
112	help
113	  Support for UniPhier FIFO-builtin I2C controller driver.
114	  This I2C controller is used on PH1-Pro4 or newer UniPhier SoCs.
115
116source "drivers/i2c/muxes/Kconfig"
117
118endmenu
119