1 /* 2 * (C) Copyright 2012-2013, Xilinx, Michal Simek 3 * 4 * (C) Copyright 2012 5 * Joe Hershberger <joe.hershberger@ni.com> 6 * 7 * SPDX-License-Identifier: GPL-2.0+ 8 */ 9 10 #include <common.h> 11 #include <asm/io.h> 12 #include <zynqpl.h> 13 #include <asm/sizes.h> 14 #include <asm/arch/hardware.h> 15 #include <asm/arch/sys_proto.h> 16 17 #define DEVCFG_CTRL_PCFG_PROG_B 0x40000000 18 #define DEVCFG_ISR_FATAL_ERROR_MASK 0x00740040 19 #define DEVCFG_ISR_ERROR_FLAGS_MASK 0x00340840 20 #define DEVCFG_ISR_RX_FIFO_OV 0x00040000 21 #define DEVCFG_ISR_DMA_DONE 0x00002000 22 #define DEVCFG_ISR_PCFG_DONE 0x00000004 23 #define DEVCFG_STATUS_DMA_CMD_Q_F 0x80000000 24 #define DEVCFG_STATUS_DMA_CMD_Q_E 0x40000000 25 #define DEVCFG_STATUS_DMA_DONE_CNT_MASK 0x30000000 26 #define DEVCFG_STATUS_PCFG_INIT 0x00000010 27 #define DEVCFG_MCTRL_PCAP_LPBK 0x00000010 28 #define DEVCFG_MCTRL_RFIFO_FLUSH 0x00000002 29 #define DEVCFG_MCTRL_WFIFO_FLUSH 0x00000001 30 31 #ifndef CONFIG_SYS_FPGA_WAIT 32 #define CONFIG_SYS_FPGA_WAIT CONFIG_SYS_HZ/100 /* 10 ms */ 33 #endif 34 35 #ifndef CONFIG_SYS_FPGA_PROG_TIME 36 #define CONFIG_SYS_FPGA_PROG_TIME (CONFIG_SYS_HZ * 4) /* 4 s */ 37 #endif 38 39 int zynq_info(Xilinx_desc *desc) 40 { 41 return FPGA_SUCCESS; 42 } 43 44 #define DUMMY_WORD 0xffffffff 45 46 /* Xilinx binary format header */ 47 static const u32 bin_format[] = { 48 DUMMY_WORD, /* Dummy words */ 49 DUMMY_WORD, 50 DUMMY_WORD, 51 DUMMY_WORD, 52 DUMMY_WORD, 53 DUMMY_WORD, 54 DUMMY_WORD, 55 DUMMY_WORD, 56 0x000000bb, /* Sync word */ 57 0x11220044, /* Sync word */ 58 DUMMY_WORD, 59 DUMMY_WORD, 60 0xaa995566, /* Sync word */ 61 }; 62 63 #define SWAP_NO 1 64 #define SWAP_DONE 2 65 66 /* 67 * Load the whole word from unaligned buffer 68 * Keep in your mind that it is byte loading on little-endian system 69 */ 70 static u32 load_word(const void *buf, u32 swap) 71 { 72 u32 word = 0; 73 u8 *bitc = (u8 *)buf; 74 int p; 75 76 if (swap == SWAP_NO) { 77 for (p = 0; p < 4; p++) { 78 word <<= 8; 79 word |= bitc[p]; 80 } 81 } else { 82 for (p = 3; p >= 0; p--) { 83 word <<= 8; 84 word |= bitc[p]; 85 } 86 } 87 88 return word; 89 } 90 91 static u32 check_header(const void *buf) 92 { 93 u32 i, pattern; 94 int swap = SWAP_NO; 95 u32 *test = (u32 *)buf; 96 97 debug("%s: Let's check bitstream header\n", __func__); 98 99 /* Checking that passing bin is not a bitstream */ 100 for (i = 0; i < ARRAY_SIZE(bin_format); i++) { 101 pattern = load_word(&test[i], swap); 102 103 /* 104 * Bitstreams in binary format are swapped 105 * compare to regular bistream. 106 * Do not swap dummy word but if swap is done assume 107 * that parsing buffer is binary format 108 */ 109 if ((__swab32(pattern) != DUMMY_WORD) && 110 (__swab32(pattern) == bin_format[i])) { 111 pattern = __swab32(pattern); 112 swap = SWAP_DONE; 113 debug("%s: data swapped - let's swap\n", __func__); 114 } 115 116 debug("%s: %d/%x: pattern %x/%x bin_format\n", __func__, i, 117 (u32)&test[i], pattern, bin_format[i]); 118 if (pattern != bin_format[i]) { 119 debug("%s: Bitstream is not recognized\n", __func__); 120 return 0; 121 } 122 } 123 debug("%s: Found bitstream header at %x %s swapinng\n", __func__, 124 (u32)buf, swap == SWAP_NO ? "without" : "with"); 125 126 return swap; 127 } 128 129 static void *check_data(u8 *buf, size_t bsize, u32 *swap) 130 { 131 u32 word, p = 0; /* possition */ 132 133 /* Because buf doesn't need to be aligned let's read it by chars */ 134 for (p = 0; p < bsize; p++) { 135 word = load_word(&buf[p], SWAP_NO); 136 debug("%s: word %x %x/%x\n", __func__, word, p, (u32)&buf[p]); 137 138 /* Find the first bitstream dummy word */ 139 if (word == DUMMY_WORD) { 140 debug("%s: Found dummy word at position %x/%x\n", 141 __func__, p, (u32)&buf[p]); 142 *swap = check_header(&buf[p]); 143 if (*swap) { 144 /* FIXME add full bitstream checking here */ 145 return &buf[p]; 146 } 147 } 148 /* Loop can be huge - support CTRL + C */ 149 if (ctrlc()) 150 return 0; 151 } 152 return 0; 153 } 154 155 156 int zynq_load(Xilinx_desc *desc, const void *buf, size_t bsize) 157 { 158 unsigned long ts; /* Timestamp */ 159 u32 partialbit = 0; 160 u32 i, control, isr_status, status, swap, diff; 161 u32 *buf_start; 162 163 /* Detect if we are going working with partial or full bitstream */ 164 if (bsize != desc->size) { 165 printf("%s: Working with partial bitstream\n", __func__); 166 partialbit = 1; 167 } 168 169 buf_start = check_data((u8 *)buf, bsize, &swap); 170 if (!buf_start) 171 return FPGA_FAIL; 172 173 /* Check if data is postpone from start */ 174 diff = (u32)buf_start - (u32)buf; 175 if (diff) { 176 printf("%s: Bitstream is not validated yet (diff %x)\n", 177 __func__, diff); 178 return FPGA_FAIL; 179 } 180 181 if ((u32)buf < SZ_1M) { 182 printf("%s: Bitstream has to be placed up to 1MB (%x)\n", 183 __func__, (u32)buf); 184 return FPGA_FAIL; 185 } 186 187 if ((u32)buf != ALIGN((u32)buf, ARCH_DMA_MINALIGN)) { 188 u32 *new_buf = (u32 *)ALIGN((u32)buf, ARCH_DMA_MINALIGN); 189 190 printf("%s: Align buffer at %x to %x(swap %d)\n", __func__, 191 (u32)buf_start, (u32)new_buf, swap); 192 193 for (i = 0; i < (bsize/4); i++) 194 new_buf[i] = load_word(&buf_start[i], swap); 195 196 swap = SWAP_DONE; 197 buf = new_buf; 198 } else if (swap != SWAP_DONE) { 199 /* For bitstream which are aligned */ 200 u32 *new_buf = (u32 *)buf; 201 202 printf("%s: Bitstream is not swapped(%d) - swap it\n", __func__, 203 swap); 204 205 for (i = 0; i < (bsize/4); i++) 206 new_buf[i] = load_word(&buf_start[i], swap); 207 208 swap = SWAP_DONE; 209 } 210 211 /* Clear loopback bit */ 212 clrbits_le32(&devcfg_base->mctrl, DEVCFG_MCTRL_PCAP_LPBK); 213 214 if (!partialbit) { 215 zynq_slcr_devcfg_disable(); 216 217 /* Setting PCFG_PROG_B signal to high */ 218 control = readl(&devcfg_base->ctrl); 219 writel(control | DEVCFG_CTRL_PCFG_PROG_B, &devcfg_base->ctrl); 220 /* Setting PCFG_PROG_B signal to low */ 221 writel(control & ~DEVCFG_CTRL_PCFG_PROG_B, &devcfg_base->ctrl); 222 223 /* Polling the PCAP_INIT status for Reset */ 224 ts = get_timer(0); 225 while (readl(&devcfg_base->status) & DEVCFG_STATUS_PCFG_INIT) { 226 if (get_timer(ts) > CONFIG_SYS_FPGA_WAIT) { 227 printf("%s: Timeout wait for INIT to clear\n", 228 __func__); 229 return FPGA_FAIL; 230 } 231 } 232 233 /* Setting PCFG_PROG_B signal to high */ 234 writel(control | DEVCFG_CTRL_PCFG_PROG_B, &devcfg_base->ctrl); 235 236 /* Polling the PCAP_INIT status for Set */ 237 ts = get_timer(0); 238 while (!(readl(&devcfg_base->status) & 239 DEVCFG_STATUS_PCFG_INIT)) { 240 if (get_timer(ts) > CONFIG_SYS_FPGA_WAIT) { 241 printf("%s: Timeout wait for INIT to set\n", 242 __func__); 243 return FPGA_FAIL; 244 } 245 } 246 } 247 248 isr_status = readl(&devcfg_base->int_sts); 249 250 /* Clear it all, so if Boot ROM comes back, it can proceed */ 251 writel(0xFFFFFFFF, &devcfg_base->int_sts); 252 253 if (isr_status & DEVCFG_ISR_FATAL_ERROR_MASK) { 254 debug("%s: Fatal errors in PCAP 0x%X\n", __func__, isr_status); 255 256 /* If RX FIFO overflow, need to flush RX FIFO first */ 257 if (isr_status & DEVCFG_ISR_RX_FIFO_OV) { 258 writel(DEVCFG_MCTRL_RFIFO_FLUSH, &devcfg_base->mctrl); 259 writel(0xFFFFFFFF, &devcfg_base->int_sts); 260 } 261 return FPGA_FAIL; 262 } 263 264 status = readl(&devcfg_base->status); 265 266 debug("%s: Status = 0x%08X\n", __func__, status); 267 268 if (status & DEVCFG_STATUS_DMA_CMD_Q_F) { 269 debug("%s: Error: device busy\n", __func__); 270 return FPGA_FAIL; 271 } 272 273 debug("%s: Device ready\n", __func__); 274 275 if (!(status & DEVCFG_STATUS_DMA_CMD_Q_E)) { 276 if (!(readl(&devcfg_base->int_sts) & DEVCFG_ISR_DMA_DONE)) { 277 /* Error state, transfer cannot occur */ 278 debug("%s: ISR indicates error\n", __func__); 279 return FPGA_FAIL; 280 } else { 281 /* Clear out the status */ 282 writel(DEVCFG_ISR_DMA_DONE, &devcfg_base->int_sts); 283 } 284 } 285 286 if (status & DEVCFG_STATUS_DMA_DONE_CNT_MASK) { 287 /* Clear the count of completed DMA transfers */ 288 writel(DEVCFG_STATUS_DMA_DONE_CNT_MASK, &devcfg_base->status); 289 } 290 291 debug("%s: Source = 0x%08X\n", __func__, (u32)buf); 292 debug("%s: Size = %zu\n", __func__, bsize); 293 294 /* flush(clean & invalidate) d-cache range buf */ 295 flush_dcache_range((u32)buf, (u32)buf + 296 roundup(bsize, ARCH_DMA_MINALIGN)); 297 298 /* Set up the transfer */ 299 writel((u32)buf | 1, &devcfg_base->dma_src_addr); 300 writel(0xFFFFFFFF, &devcfg_base->dma_dst_addr); 301 writel(bsize >> 2, &devcfg_base->dma_src_len); 302 writel(0, &devcfg_base->dma_dst_len); 303 304 isr_status = readl(&devcfg_base->int_sts); 305 306 /* Polling the PCAP_INIT status for Set */ 307 ts = get_timer(0); 308 while (!(isr_status & DEVCFG_ISR_DMA_DONE)) { 309 if (isr_status & DEVCFG_ISR_ERROR_FLAGS_MASK) { 310 debug("%s: Error: isr = 0x%08X\n", __func__, 311 isr_status); 312 debug("%s: Write count = 0x%08X\n", __func__, 313 readl(&devcfg_base->write_count)); 314 debug("%s: Read count = 0x%08X\n", __func__, 315 readl(&devcfg_base->read_count)); 316 317 return FPGA_FAIL; 318 } 319 if (get_timer(ts) > CONFIG_SYS_FPGA_PROG_TIME) { 320 printf("%s: Timeout wait for DMA to complete\n", 321 __func__); 322 return FPGA_FAIL; 323 } 324 isr_status = readl(&devcfg_base->int_sts); 325 } 326 327 debug("%s: DMA transfer is done\n", __func__); 328 329 /* Check FPGA configuration completion */ 330 ts = get_timer(0); 331 while (!(isr_status & DEVCFG_ISR_PCFG_DONE)) { 332 if (get_timer(ts) > CONFIG_SYS_FPGA_WAIT) { 333 printf("%s: Timeout wait for FPGA to config\n", 334 __func__); 335 return FPGA_FAIL; 336 } 337 isr_status = readl(&devcfg_base->int_sts); 338 } 339 340 debug("%s: FPGA config done\n", __func__); 341 342 /* Clear out the DMA status */ 343 writel(DEVCFG_ISR_DMA_DONE, &devcfg_base->int_sts); 344 345 if (!partialbit) 346 zynq_slcr_devcfg_enable(); 347 348 return FPGA_SUCCESS; 349 } 350 351 int zynq_dump(Xilinx_desc *desc, const void *buf, size_t bsize) 352 { 353 return FPGA_FAIL; 354 } 355