1 /* 2 * Copyright (C) Marvell International Ltd. and its affiliates 3 * 4 * SPDX-License-Identifier: GPL-2.0 5 */ 6 7 #ifndef __DDR3_AXP_CONFIG_H 8 #define __DDR3_AXP_CONFIG_H 9 10 /* 11 * DDR3_LOG_LEVEL Information 12 * 13 * Level 0: Provides an error code in a case of failure, RL, WL errors 14 * and other algorithm failure 15 * Level 1: Provides the D-Unit setup (SPD/Static configuration) 16 * Level 2: Provides the windows margin as a results of DQS centeralization 17 * Level 3: Provides the windows margin of each DQ as a results of DQS 18 * centeralization 19 */ 20 #ifdef CONFIG_DDR_LOG_LEVEL 21 #define DDR3_LOG_LEVEL CONFIG_DDR_LOG_LEVEL 22 #else 23 #define DDR3_LOG_LEVEL 0 24 #endif 25 26 #define DDR3_PBS 1 27 28 /* This flag allows the execution of SW WL/RL upon HW failure */ 29 #define DDR3_RUN_SW_WHEN_HW_FAIL 1 30 31 /* 32 * General Configurations 33 * 34 * The following parameters are required for proper setup: 35 * 36 * DDR_TARGET_FABRIC - Set desired fabric configuration 37 * (for sample@Reset fabfreq parameter) 38 * DRAM_ECC - Set ECC support 1/0 39 * BUS_WIDTH - 64/32 bit 40 * CONFIG_SPD_EEPROM - Enables auto detection of DIMMs and their timing values 41 * DQS_CLK_ALIGNED - Set this if CLK and DQS signals are aligned on board 42 * MIXED_DIMM_STATIC - Mixed DIMM + On board devices support (ODT registers 43 * values are taken statically) 44 * DDR3_TRAINING_DEBUG - Debug prints of internal code 45 */ 46 #define DDR_TARGET_FABRIC 5 47 #define DRAM_ECC 1 48 49 #ifdef MV_DDR_32BIT 50 #define BUS_WIDTH 32 51 #else 52 #define BUS_WIDTH 64 53 #endif 54 55 #undef DQS_CLK_ALIGNED 56 #undef MIXED_DIMM_STATIC 57 #define DDR3_TRAINING_DEBUG 0 58 #define REG_DIMM_SKIP_WL 0 59 60 /* Marvell boards specific configurations */ 61 #if defined(DB_78X60_PCAC) 62 #undef CONFIG_SPD_EEPROM 63 #define STATIC_TRAINING 64 #endif 65 66 #if defined(DB_78X60_AMC) 67 #undef CONFIG_SPD_EEPROM 68 #undef DRAM_ECC 69 #define DRAM_ECC 1 70 #endif 71 72 #ifdef CONFIG_SPD_EEPROM 73 /* 74 * DIMM support parameters: 75 * DRAM_2T - Set Desired 2T Mode - 0 - 1T, 0x1 - 2T, 0x2 - 3T 76 * DIMM_CS_BITMAP - bitmap representing the optional CS in DIMMs 77 * (0xF=CS0+CS1+CS2+CS3, 0xC=CS2+CS3...) 78 */ 79 #define DRAM_2T 0x0 80 #define DIMM_CS_BITMAP 0xF 81 #define DUNIT_SPD 82 #endif 83 84 #ifdef DRAM_ECC 85 /* 86 * ECC support parameters: 87 * 88 * U_BOOT_START_ADDR, U_BOOT_SCRUB_SIZE - relevant when using ECC and need 89 * to configure the scrubbing area 90 */ 91 #define TRAINING_SIZE 0x20000 92 #define U_BOOT_START_ADDR 0 93 #define U_BOOT_SCRUB_SIZE 0x1000000 /* TRAINING_SIZE */ 94 #endif 95 96 /* 97 * Registered DIMM Support - In case registered DIMM is attached, 98 * please supply the following values: 99 * (see JEDEC - JESD82-29A "Definition of the SSTE32882 Registering Clock 100 * Driver with Parity and Quad Chip 101 * Selects for DDR3/DDR3L/DDR3U RDIMM 1.5 V/1.35 V/1.25 V Applications") 102 * RC0: Global Features Control Word 103 * RC1: Clock Driver Enable Control Word 104 * RC2: Timing Control Word 105 * RC3-RC5 - taken from SPD 106 * RC8: Additional IBT Setting Control Word 107 * RC9: Power Saving Settings Control Word 108 * RC10: Encoding for RDIMM Operating Speed 109 * RC11: Operating Voltage VDD and VREFCA Control Word 110 */ 111 #define RDIMM_RC0 0 112 #define RDIMM_RC1 0 113 #define RDIMM_RC2 0 114 #define RDIMM_RC8 0 115 #define RDIMM_RC9 0 116 #define RDIMM_RC10 0x2 117 #define RDIMM_RC11 0x0 118 119 #if defined(MIXED_DIMM_STATIC) || !defined(CONFIG_SPD_EEPROM) 120 #define DUNIT_STATIC 121 #endif 122 123 #if defined(MIXED_DIMM_STATIC) || defined(CONFIG_SPD_EEPROM) 124 /* 125 * This flag allows the user to change the dram refresh cycle in ps, 126 * only in case of SPD or MIX DIMM topology 127 */ 128 #define TREFI_USER_EN 129 130 #ifdef TREFI_USER_EN 131 #define TREFI_USER 3900000 132 #endif 133 #endif 134 135 #ifdef CONFIG_SPD_EEPROM 136 /* 137 * AUTO_DETECTION_SUPPORT - relevant ONLY for Marvell DB boards. 138 * Enables I2C auto detection different options 139 */ 140 #if defined(CONFIG_DB_88F78X60) || defined(CONFIG_DB_88F78X60_REV2) || \ 141 defined(CONFIG_DB_784MP_GP) 142 #define AUTO_DETECTION_SUPPORT 143 #endif 144 #endif 145 146 #endif /* __DDR3_AXP_CONFIG_H */ 147