1 /* 2 * Copyright 2008, 2010-2012 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 #include <common.h> 8 #include <hwconfig.h> 9 #include <fsl_ddr_sdram.h> 10 11 #include <fsl_ddr.h> 12 13 /* 14 * Use our own stack based buffer before relocation to allow accessing longer 15 * hwconfig strings that might be in the environment before we've relocated. 16 * This is pretty fragile on both the use of stack and if the buffer is big 17 * enough. However we will get a warning from getenv_f for the later. 18 */ 19 20 /* Board-specific functions defined in each board's ddr.c */ 21 extern void fsl_ddr_board_options(memctl_options_t *popts, 22 dimm_params_t *pdimm, 23 unsigned int ctrl_num); 24 25 struct dynamic_odt { 26 unsigned int odt_rd_cfg; 27 unsigned int odt_wr_cfg; 28 unsigned int odt_rtt_norm; 29 unsigned int odt_rtt_wr; 30 }; 31 32 #ifdef CONFIG_SYS_FSL_DDR3 33 static const struct dynamic_odt single_Q[4] = { 34 { /* cs0 */ 35 FSL_DDR_ODT_NEVER, 36 FSL_DDR_ODT_CS_AND_OTHER_DIMM, 37 DDR3_RTT_20_OHM, 38 DDR3_RTT_120_OHM 39 }, 40 { /* cs1 */ 41 FSL_DDR_ODT_NEVER, 42 FSL_DDR_ODT_NEVER, /* tied high */ 43 DDR3_RTT_OFF, 44 DDR3_RTT_120_OHM 45 }, 46 { /* cs2 */ 47 FSL_DDR_ODT_NEVER, 48 FSL_DDR_ODT_CS_AND_OTHER_DIMM, 49 DDR3_RTT_20_OHM, 50 DDR3_RTT_120_OHM 51 }, 52 { /* cs3 */ 53 FSL_DDR_ODT_NEVER, 54 FSL_DDR_ODT_NEVER, /* tied high */ 55 DDR3_RTT_OFF, 56 DDR3_RTT_120_OHM 57 } 58 }; 59 60 static const struct dynamic_odt single_D[4] = { 61 { /* cs0 */ 62 FSL_DDR_ODT_NEVER, 63 FSL_DDR_ODT_ALL, 64 DDR3_RTT_40_OHM, 65 DDR3_RTT_OFF 66 }, 67 { /* cs1 */ 68 FSL_DDR_ODT_NEVER, 69 FSL_DDR_ODT_NEVER, 70 DDR3_RTT_OFF, 71 DDR3_RTT_OFF 72 }, 73 {0, 0, 0, 0}, 74 {0, 0, 0, 0} 75 }; 76 77 static const struct dynamic_odt single_S[4] = { 78 { /* cs0 */ 79 FSL_DDR_ODT_NEVER, 80 FSL_DDR_ODT_ALL, 81 DDR3_RTT_40_OHM, 82 DDR3_RTT_OFF 83 }, 84 {0, 0, 0, 0}, 85 {0, 0, 0, 0}, 86 {0, 0, 0, 0}, 87 }; 88 89 static const struct dynamic_odt dual_DD[4] = { 90 { /* cs0 */ 91 FSL_DDR_ODT_NEVER, 92 FSL_DDR_ODT_SAME_DIMM, 93 DDR3_RTT_120_OHM, 94 DDR3_RTT_OFF 95 }, 96 { /* cs1 */ 97 FSL_DDR_ODT_OTHER_DIMM, 98 FSL_DDR_ODT_OTHER_DIMM, 99 DDR3_RTT_30_OHM, 100 DDR3_RTT_OFF 101 }, 102 { /* cs2 */ 103 FSL_DDR_ODT_NEVER, 104 FSL_DDR_ODT_SAME_DIMM, 105 DDR3_RTT_120_OHM, 106 DDR3_RTT_OFF 107 }, 108 { /* cs3 */ 109 FSL_DDR_ODT_OTHER_DIMM, 110 FSL_DDR_ODT_OTHER_DIMM, 111 DDR3_RTT_30_OHM, 112 DDR3_RTT_OFF 113 } 114 }; 115 116 static const struct dynamic_odt dual_DS[4] = { 117 { /* cs0 */ 118 FSL_DDR_ODT_NEVER, 119 FSL_DDR_ODT_SAME_DIMM, 120 DDR3_RTT_120_OHM, 121 DDR3_RTT_OFF 122 }, 123 { /* cs1 */ 124 FSL_DDR_ODT_OTHER_DIMM, 125 FSL_DDR_ODT_OTHER_DIMM, 126 DDR3_RTT_30_OHM, 127 DDR3_RTT_OFF 128 }, 129 { /* cs2 */ 130 FSL_DDR_ODT_OTHER_DIMM, 131 FSL_DDR_ODT_ALL, 132 DDR3_RTT_20_OHM, 133 DDR3_RTT_120_OHM 134 }, 135 {0, 0, 0, 0} 136 }; 137 static const struct dynamic_odt dual_SD[4] = { 138 { /* cs0 */ 139 FSL_DDR_ODT_OTHER_DIMM, 140 FSL_DDR_ODT_ALL, 141 DDR3_RTT_20_OHM, 142 DDR3_RTT_120_OHM 143 }, 144 {0, 0, 0, 0}, 145 { /* cs2 */ 146 FSL_DDR_ODT_NEVER, 147 FSL_DDR_ODT_SAME_DIMM, 148 DDR3_RTT_120_OHM, 149 DDR3_RTT_OFF 150 }, 151 { /* cs3 */ 152 FSL_DDR_ODT_OTHER_DIMM, 153 FSL_DDR_ODT_OTHER_DIMM, 154 DDR3_RTT_20_OHM, 155 DDR3_RTT_OFF 156 } 157 }; 158 159 static const struct dynamic_odt dual_SS[4] = { 160 { /* cs0 */ 161 FSL_DDR_ODT_OTHER_DIMM, 162 FSL_DDR_ODT_ALL, 163 DDR3_RTT_30_OHM, 164 DDR3_RTT_120_OHM 165 }, 166 {0, 0, 0, 0}, 167 { /* cs2 */ 168 FSL_DDR_ODT_OTHER_DIMM, 169 FSL_DDR_ODT_ALL, 170 DDR3_RTT_30_OHM, 171 DDR3_RTT_120_OHM 172 }, 173 {0, 0, 0, 0} 174 }; 175 176 static const struct dynamic_odt dual_D0[4] = { 177 { /* cs0 */ 178 FSL_DDR_ODT_NEVER, 179 FSL_DDR_ODT_SAME_DIMM, 180 DDR3_RTT_40_OHM, 181 DDR3_RTT_OFF 182 }, 183 { /* cs1 */ 184 FSL_DDR_ODT_NEVER, 185 FSL_DDR_ODT_NEVER, 186 DDR3_RTT_OFF, 187 DDR3_RTT_OFF 188 }, 189 {0, 0, 0, 0}, 190 {0, 0, 0, 0} 191 }; 192 193 static const struct dynamic_odt dual_0D[4] = { 194 {0, 0, 0, 0}, 195 {0, 0, 0, 0}, 196 { /* cs2 */ 197 FSL_DDR_ODT_NEVER, 198 FSL_DDR_ODT_SAME_DIMM, 199 DDR3_RTT_40_OHM, 200 DDR3_RTT_OFF 201 }, 202 { /* cs3 */ 203 FSL_DDR_ODT_NEVER, 204 FSL_DDR_ODT_NEVER, 205 DDR3_RTT_OFF, 206 DDR3_RTT_OFF 207 } 208 }; 209 210 static const struct dynamic_odt dual_S0[4] = { 211 { /* cs0 */ 212 FSL_DDR_ODT_NEVER, 213 FSL_DDR_ODT_CS, 214 DDR3_RTT_40_OHM, 215 DDR3_RTT_OFF 216 }, 217 {0, 0, 0, 0}, 218 {0, 0, 0, 0}, 219 {0, 0, 0, 0} 220 221 }; 222 223 static const struct dynamic_odt dual_0S[4] = { 224 {0, 0, 0, 0}, 225 {0, 0, 0, 0}, 226 { /* cs2 */ 227 FSL_DDR_ODT_NEVER, 228 FSL_DDR_ODT_CS, 229 DDR3_RTT_40_OHM, 230 DDR3_RTT_OFF 231 }, 232 {0, 0, 0, 0} 233 234 }; 235 236 static const struct dynamic_odt odt_unknown[4] = { 237 { /* cs0 */ 238 FSL_DDR_ODT_NEVER, 239 FSL_DDR_ODT_CS, 240 DDR3_RTT_120_OHM, 241 DDR3_RTT_OFF 242 }, 243 { /* cs1 */ 244 FSL_DDR_ODT_NEVER, 245 FSL_DDR_ODT_CS, 246 DDR3_RTT_120_OHM, 247 DDR3_RTT_OFF 248 }, 249 { /* cs2 */ 250 FSL_DDR_ODT_NEVER, 251 FSL_DDR_ODT_CS, 252 DDR3_RTT_120_OHM, 253 DDR3_RTT_OFF 254 }, 255 { /* cs3 */ 256 FSL_DDR_ODT_NEVER, 257 FSL_DDR_ODT_CS, 258 DDR3_RTT_120_OHM, 259 DDR3_RTT_OFF 260 } 261 }; 262 #else /* CONFIG_SYS_FSL_DDR3 */ 263 static const struct dynamic_odt single_Q[4] = { 264 {0, 0, 0, 0}, 265 {0, 0, 0, 0}, 266 {0, 0, 0, 0}, 267 {0, 0, 0, 0} 268 }; 269 270 static const struct dynamic_odt single_D[4] = { 271 { /* cs0 */ 272 FSL_DDR_ODT_NEVER, 273 FSL_DDR_ODT_ALL, 274 DDR2_RTT_150_OHM, 275 DDR2_RTT_OFF 276 }, 277 { /* cs1 */ 278 FSL_DDR_ODT_NEVER, 279 FSL_DDR_ODT_NEVER, 280 DDR2_RTT_OFF, 281 DDR2_RTT_OFF 282 }, 283 {0, 0, 0, 0}, 284 {0, 0, 0, 0} 285 }; 286 287 static const struct dynamic_odt single_S[4] = { 288 { /* cs0 */ 289 FSL_DDR_ODT_NEVER, 290 FSL_DDR_ODT_ALL, 291 DDR2_RTT_150_OHM, 292 DDR2_RTT_OFF 293 }, 294 {0, 0, 0, 0}, 295 {0, 0, 0, 0}, 296 {0, 0, 0, 0}, 297 }; 298 299 static const struct dynamic_odt dual_DD[4] = { 300 { /* cs0 */ 301 FSL_DDR_ODT_OTHER_DIMM, 302 FSL_DDR_ODT_OTHER_DIMM, 303 DDR2_RTT_75_OHM, 304 DDR2_RTT_OFF 305 }, 306 { /* cs1 */ 307 FSL_DDR_ODT_NEVER, 308 FSL_DDR_ODT_NEVER, 309 DDR2_RTT_OFF, 310 DDR2_RTT_OFF 311 }, 312 { /* cs2 */ 313 FSL_DDR_ODT_OTHER_DIMM, 314 FSL_DDR_ODT_OTHER_DIMM, 315 DDR2_RTT_75_OHM, 316 DDR2_RTT_OFF 317 }, 318 { /* cs3 */ 319 FSL_DDR_ODT_NEVER, 320 FSL_DDR_ODT_NEVER, 321 DDR2_RTT_OFF, 322 DDR2_RTT_OFF 323 } 324 }; 325 326 static const struct dynamic_odt dual_DS[4] = { 327 { /* cs0 */ 328 FSL_DDR_ODT_OTHER_DIMM, 329 FSL_DDR_ODT_OTHER_DIMM, 330 DDR2_RTT_75_OHM, 331 DDR2_RTT_OFF 332 }, 333 { /* cs1 */ 334 FSL_DDR_ODT_NEVER, 335 FSL_DDR_ODT_NEVER, 336 DDR2_RTT_OFF, 337 DDR2_RTT_OFF 338 }, 339 { /* cs2 */ 340 FSL_DDR_ODT_OTHER_DIMM, 341 FSL_DDR_ODT_OTHER_DIMM, 342 DDR2_RTT_75_OHM, 343 DDR2_RTT_OFF 344 }, 345 {0, 0, 0, 0} 346 }; 347 348 static const struct dynamic_odt dual_SD[4] = { 349 { /* cs0 */ 350 FSL_DDR_ODT_OTHER_DIMM, 351 FSL_DDR_ODT_OTHER_DIMM, 352 DDR2_RTT_75_OHM, 353 DDR2_RTT_OFF 354 }, 355 {0, 0, 0, 0}, 356 { /* cs2 */ 357 FSL_DDR_ODT_OTHER_DIMM, 358 FSL_DDR_ODT_OTHER_DIMM, 359 DDR2_RTT_75_OHM, 360 DDR2_RTT_OFF 361 }, 362 { /* cs3 */ 363 FSL_DDR_ODT_NEVER, 364 FSL_DDR_ODT_NEVER, 365 DDR2_RTT_OFF, 366 DDR2_RTT_OFF 367 } 368 }; 369 370 static const struct dynamic_odt dual_SS[4] = { 371 { /* cs0 */ 372 FSL_DDR_ODT_OTHER_DIMM, 373 FSL_DDR_ODT_OTHER_DIMM, 374 DDR2_RTT_75_OHM, 375 DDR2_RTT_OFF 376 }, 377 {0, 0, 0, 0}, 378 { /* cs2 */ 379 FSL_DDR_ODT_OTHER_DIMM, 380 FSL_DDR_ODT_OTHER_DIMM, 381 DDR2_RTT_75_OHM, 382 DDR2_RTT_OFF 383 }, 384 {0, 0, 0, 0} 385 }; 386 387 static const struct dynamic_odt dual_D0[4] = { 388 { /* cs0 */ 389 FSL_DDR_ODT_NEVER, 390 FSL_DDR_ODT_ALL, 391 DDR2_RTT_150_OHM, 392 DDR2_RTT_OFF 393 }, 394 { /* cs1 */ 395 FSL_DDR_ODT_NEVER, 396 FSL_DDR_ODT_NEVER, 397 DDR2_RTT_OFF, 398 DDR2_RTT_OFF 399 }, 400 {0, 0, 0, 0}, 401 {0, 0, 0, 0} 402 }; 403 404 static const struct dynamic_odt dual_0D[4] = { 405 {0, 0, 0, 0}, 406 {0, 0, 0, 0}, 407 { /* cs2 */ 408 FSL_DDR_ODT_NEVER, 409 FSL_DDR_ODT_ALL, 410 DDR2_RTT_150_OHM, 411 DDR2_RTT_OFF 412 }, 413 { /* cs3 */ 414 FSL_DDR_ODT_NEVER, 415 FSL_DDR_ODT_NEVER, 416 DDR2_RTT_OFF, 417 DDR2_RTT_OFF 418 } 419 }; 420 421 static const struct dynamic_odt dual_S0[4] = { 422 { /* cs0 */ 423 FSL_DDR_ODT_NEVER, 424 FSL_DDR_ODT_CS, 425 DDR2_RTT_150_OHM, 426 DDR2_RTT_OFF 427 }, 428 {0, 0, 0, 0}, 429 {0, 0, 0, 0}, 430 {0, 0, 0, 0} 431 432 }; 433 434 static const struct dynamic_odt dual_0S[4] = { 435 {0, 0, 0, 0}, 436 {0, 0, 0, 0}, 437 { /* cs2 */ 438 FSL_DDR_ODT_NEVER, 439 FSL_DDR_ODT_CS, 440 DDR2_RTT_150_OHM, 441 DDR2_RTT_OFF 442 }, 443 {0, 0, 0, 0} 444 445 }; 446 447 static const struct dynamic_odt odt_unknown[4] = { 448 { /* cs0 */ 449 FSL_DDR_ODT_NEVER, 450 FSL_DDR_ODT_CS, 451 DDR2_RTT_75_OHM, 452 DDR2_RTT_OFF 453 }, 454 { /* cs1 */ 455 FSL_DDR_ODT_NEVER, 456 FSL_DDR_ODT_NEVER, 457 DDR2_RTT_OFF, 458 DDR2_RTT_OFF 459 }, 460 { /* cs2 */ 461 FSL_DDR_ODT_NEVER, 462 FSL_DDR_ODT_CS, 463 DDR2_RTT_75_OHM, 464 DDR2_RTT_OFF 465 }, 466 { /* cs3 */ 467 FSL_DDR_ODT_NEVER, 468 FSL_DDR_ODT_NEVER, 469 DDR2_RTT_OFF, 470 DDR2_RTT_OFF 471 } 472 }; 473 #endif 474 475 /* 476 * Automatically seleect bank interleaving mode based on DIMMs 477 * in this order: cs0_cs1_cs2_cs3, cs0_cs1, null. 478 * This function only deal with one or two slots per controller. 479 */ 480 static inline unsigned int auto_bank_intlv(dimm_params_t *pdimm) 481 { 482 #if (CONFIG_DIMM_SLOTS_PER_CTLR == 1) 483 if (pdimm[0].n_ranks == 4) 484 return FSL_DDR_CS0_CS1_CS2_CS3; 485 else if (pdimm[0].n_ranks == 2) 486 return FSL_DDR_CS0_CS1; 487 #elif (CONFIG_DIMM_SLOTS_PER_CTLR == 2) 488 #ifdef CONFIG_FSL_DDR_FIRST_SLOT_QUAD_CAPABLE 489 if (pdimm[0].n_ranks == 4) 490 return FSL_DDR_CS0_CS1_CS2_CS3; 491 #endif 492 if (pdimm[0].n_ranks == 2) { 493 if (pdimm[1].n_ranks == 2) 494 return FSL_DDR_CS0_CS1_CS2_CS3; 495 else 496 return FSL_DDR_CS0_CS1; 497 } 498 #endif 499 return 0; 500 } 501 502 unsigned int populate_memctl_options(int all_dimms_registered, 503 memctl_options_t *popts, 504 dimm_params_t *pdimm, 505 unsigned int ctrl_num) 506 { 507 unsigned int i; 508 char buffer[HWCONFIG_BUFFER_SIZE]; 509 char *buf = NULL; 510 #if defined(CONFIG_SYS_FSL_DDR3) || defined(CONFIG_SYS_FSL_DDR2) 511 const struct dynamic_odt *pdodt = odt_unknown; 512 #endif 513 ulong ddr_freq; 514 515 /* 516 * Extract hwconfig from environment since we have not properly setup 517 * the environment but need it for ddr config params 518 */ 519 if (getenv_f("hwconfig", buffer, sizeof(buffer)) > 0) 520 buf = buffer; 521 522 #if defined(CONFIG_SYS_FSL_DDR3) || defined(CONFIG_SYS_FSL_DDR2) 523 /* Chip select options. */ 524 if (CONFIG_DIMM_SLOTS_PER_CTLR == 1) { 525 switch (pdimm[0].n_ranks) { 526 case 1: 527 pdodt = single_S; 528 break; 529 case 2: 530 pdodt = single_D; 531 break; 532 case 4: 533 pdodt = single_Q; 534 break; 535 } 536 } else if (CONFIG_DIMM_SLOTS_PER_CTLR == 2) { 537 switch (pdimm[0].n_ranks) { 538 #ifdef CONFIG_FSL_DDR_FIRST_SLOT_QUAD_CAPABLE 539 case 4: 540 pdodt = single_Q; 541 if (pdimm[1].n_ranks) 542 printf("Error: Quad- and Dual-rank DIMMs " 543 "cannot be used together\n"); 544 break; 545 #endif 546 case 2: 547 switch (pdimm[1].n_ranks) { 548 case 2: 549 pdodt = dual_DD; 550 break; 551 case 1: 552 pdodt = dual_DS; 553 break; 554 case 0: 555 pdodt = dual_D0; 556 break; 557 } 558 break; 559 case 1: 560 switch (pdimm[1].n_ranks) { 561 case 2: 562 pdodt = dual_SD; 563 break; 564 case 1: 565 pdodt = dual_SS; 566 break; 567 case 0: 568 pdodt = dual_S0; 569 break; 570 } 571 break; 572 case 0: 573 switch (pdimm[1].n_ranks) { 574 case 2: 575 pdodt = dual_0D; 576 break; 577 case 1: 578 pdodt = dual_0S; 579 break; 580 } 581 break; 582 } 583 } 584 #endif 585 586 /* Pick chip-select local options. */ 587 for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) { 588 #if defined(CONFIG_SYS_FSL_DDR3) || defined(CONFIG_SYS_FSL_DDR2) 589 popts->cs_local_opts[i].odt_rd_cfg = pdodt[i].odt_rd_cfg; 590 popts->cs_local_opts[i].odt_wr_cfg = pdodt[i].odt_wr_cfg; 591 popts->cs_local_opts[i].odt_rtt_norm = pdodt[i].odt_rtt_norm; 592 popts->cs_local_opts[i].odt_rtt_wr = pdodt[i].odt_rtt_wr; 593 #else 594 popts->cs_local_opts[i].odt_rd_cfg = FSL_DDR_ODT_NEVER; 595 popts->cs_local_opts[i].odt_wr_cfg = FSL_DDR_ODT_CS; 596 #endif 597 popts->cs_local_opts[i].auto_precharge = 0; 598 } 599 600 /* Pick interleaving mode. */ 601 602 /* 603 * 0 = no interleaving 604 * 1 = interleaving between 2 controllers 605 */ 606 popts->memctl_interleaving = 0; 607 608 /* 609 * 0 = cacheline 610 * 1 = page 611 * 2 = (logical) bank 612 * 3 = superbank (only if CS interleaving is enabled) 613 */ 614 popts->memctl_interleaving_mode = 0; 615 616 /* 617 * 0: cacheline: bit 30 of the 36-bit physical addr selects the memctl 618 * 1: page: bit to the left of the column bits selects the memctl 619 * 2: bank: bit to the left of the bank bits selects the memctl 620 * 3: superbank: bit to the left of the chip select selects the memctl 621 * 622 * NOTE: ba_intlv (rank interleaving) is independent of memory 623 * controller interleaving; it is only within a memory controller. 624 * Must use superbank interleaving if rank interleaving is used and 625 * memory controller interleaving is enabled. 626 */ 627 628 /* 629 * 0 = no 630 * 0x40 = CS0,CS1 631 * 0x20 = CS2,CS3 632 * 0x60 = CS0,CS1 + CS2,CS3 633 * 0x04 = CS0,CS1,CS2,CS3 634 */ 635 popts->ba_intlv_ctl = 0; 636 637 /* Memory Organization Parameters */ 638 popts->registered_dimm_en = all_dimms_registered; 639 640 /* Operational Mode Paramters */ 641 642 /* Pick ECC modes */ 643 popts->ecc_mode = 0; /* 0 = disabled, 1 = enabled */ 644 #ifdef CONFIG_DDR_ECC 645 if (hwconfig_sub_f("fsl_ddr", "ecc", buf)) { 646 if (hwconfig_subarg_cmp_f("fsl_ddr", "ecc", "on", buf)) 647 popts->ecc_mode = 1; 648 } else 649 popts->ecc_mode = 1; 650 #endif 651 popts->ecc_init_using_memctl = 1; /* 0 = use DMA, 1 = use memctl */ 652 653 /* 654 * Choose DQS config 655 * 0 for DDR1 656 * 1 for DDR2 657 */ 658 #if defined(CONFIG_SYS_FSL_DDR1) 659 popts->dqs_config = 0; 660 #elif defined(CONFIG_SYS_FSL_DDR2) || defined(CONFIG_SYS_FSL_DDR3) 661 popts->dqs_config = 1; 662 #endif 663 664 /* Choose self-refresh during sleep. */ 665 popts->self_refresh_in_sleep = 1; 666 667 /* Choose dynamic power management mode. */ 668 popts->dynamic_power = 0; 669 670 /* 671 * check first dimm for primary sdram width 672 * presuming all dimms are similar 673 * 0 = 64-bit, 1 = 32-bit, 2 = 16-bit 674 */ 675 #if defined(CONFIG_SYS_FSL_DDR1) || defined(CONFIG_SYS_FSL_DDR2) 676 if (pdimm[0].n_ranks != 0) { 677 if ((pdimm[0].data_width >= 64) && \ 678 (pdimm[0].data_width <= 72)) 679 popts->data_bus_width = 0; 680 else if ((pdimm[0].data_width >= 32) || \ 681 (pdimm[0].data_width <= 40)) 682 popts->data_bus_width = 1; 683 else { 684 panic("Error: data width %u is invalid!\n", 685 pdimm[0].data_width); 686 } 687 } 688 #else 689 if (pdimm[0].n_ranks != 0) { 690 if (pdimm[0].primary_sdram_width == 64) 691 popts->data_bus_width = 0; 692 else if (pdimm[0].primary_sdram_width == 32) 693 popts->data_bus_width = 1; 694 else if (pdimm[0].primary_sdram_width == 16) 695 popts->data_bus_width = 2; 696 else { 697 panic("Error: primary sdram width %u is invalid!\n", 698 pdimm[0].primary_sdram_width); 699 } 700 } 701 #endif 702 703 popts->x4_en = (pdimm[0].device_width == 4) ? 1 : 0; 704 705 /* Choose burst length. */ 706 #if defined(CONFIG_SYS_FSL_DDR3) 707 #if defined(CONFIG_E500MC) 708 popts->otf_burst_chop_en = 0; /* on-the-fly burst chop disable */ 709 popts->burst_length = DDR_BL8; /* Fixed 8-beat burst len */ 710 #else 711 if ((popts->data_bus_width == 1) || (popts->data_bus_width == 2)) { 712 /* 32-bit or 16-bit bus */ 713 popts->otf_burst_chop_en = 0; 714 popts->burst_length = DDR_BL8; 715 } else { 716 popts->otf_burst_chop_en = 1; /* on-the-fly burst chop */ 717 popts->burst_length = DDR_OTF; /* on-the-fly BC4 and BL8 */ 718 } 719 #endif 720 #else 721 popts->burst_length = DDR_BL4; /* has to be 4 for DDR2 */ 722 #endif 723 724 /* Choose ddr controller address mirror mode */ 725 #if defined(CONFIG_SYS_FSL_DDR3) 726 popts->mirrored_dimm = pdimm[0].mirrored_dimm; 727 #endif 728 729 /* Global Timing Parameters. */ 730 debug("mclk_ps = %u ps\n", get_memory_clk_period_ps()); 731 732 /* Pick a caslat override. */ 733 popts->cas_latency_override = 0; 734 popts->cas_latency_override_value = 3; 735 if (popts->cas_latency_override) { 736 debug("using caslat override value = %u\n", 737 popts->cas_latency_override_value); 738 } 739 740 /* Decide whether to use the computed derated latency */ 741 popts->use_derated_caslat = 0; 742 743 /* Choose an additive latency. */ 744 popts->additive_latency_override = 0; 745 popts->additive_latency_override_value = 3; 746 if (popts->additive_latency_override) { 747 debug("using additive latency override value = %u\n", 748 popts->additive_latency_override_value); 749 } 750 751 /* 752 * 2T_EN setting 753 * 754 * Factors to consider for 2T_EN: 755 * - number of DIMMs installed 756 * - number of components, number of active ranks 757 * - how much time you want to spend playing around 758 */ 759 popts->twot_en = 0; 760 popts->threet_en = 0; 761 762 /* for RDIMM, address parity enable */ 763 popts->ap_en = 1; 764 765 /* 766 * BSTTOPRE precharge interval 767 * 768 * Set this to 0 for global auto precharge 769 * 770 * FIXME: Should this be configured in picoseconds? 771 * Why it should be in ps: better understanding of this 772 * relative to actual DRAM timing parameters such as tRAS. 773 * e.g. tRAS(min) = 40 ns 774 */ 775 popts->bstopre = 0x100; 776 777 /* Minimum CKE pulse width -- tCKE(MIN) */ 778 popts->tcke_clock_pulse_width_ps 779 = mclk_to_picos(FSL_DDR_MIN_TCKE_PULSE_WIDTH_DDR); 780 781 /* 782 * Window for four activates -- tFAW 783 * 784 * FIXME: UM: applies only to DDR2/DDR3 with eight logical banks only 785 * FIXME: varies depending upon number of column addresses or data 786 * FIXME: width, was considering looking at pdimm->primary_sdram_width 787 */ 788 #if defined(CONFIG_SYS_FSL_DDR1) 789 popts->tfaw_window_four_activates_ps = mclk_to_picos(1); 790 791 #elif defined(CONFIG_SYS_FSL_DDR2) 792 /* 793 * x4/x8; some datasheets have 35000 794 * x16 wide columns only? Use 50000? 795 */ 796 popts->tfaw_window_four_activates_ps = 37500; 797 798 #elif defined(CONFIG_SYS_FSL_DDR3) 799 popts->tfaw_window_four_activates_ps = pdimm[0].tfaw_ps; 800 #endif 801 popts->zq_en = 0; 802 popts->wrlvl_en = 0; 803 #if defined(CONFIG_SYS_FSL_DDR3) 804 /* 805 * due to ddr3 dimm is fly-by topology 806 * we suggest to enable write leveling to 807 * meet the tQDSS under different loading. 808 */ 809 popts->wrlvl_en = 1; 810 popts->zq_en = 1; 811 popts->wrlvl_override = 0; 812 #endif 813 814 /* 815 * Check interleaving configuration from environment. 816 * Please refer to doc/README.fsl-ddr for the detail. 817 * 818 * If memory controller interleaving is enabled, then the data 819 * bus widths must be programmed identically for all memory controllers. 820 * 821 * Attempt to set all controllers to the same chip select 822 * interleaving mode. It will do a best effort to get the 823 * requested ranks interleaved together such that the result 824 * should be a subset of the requested configuration. 825 * 826 * if CONFIG_SYS_FSL_DDR_INTLV_256B is defined, mandatory interleaving 827 * with 256 Byte is enabled. 828 */ 829 #if (CONFIG_NUM_DDR_CONTROLLERS > 1) 830 if (!hwconfig_sub_f("fsl_ddr", "ctlr_intlv", buf)) 831 #ifdef CONFIG_SYS_FSL_DDR_INTLV_256B 832 ; 833 #else 834 goto done; 835 #endif 836 if (pdimm[0].n_ranks == 0) { 837 printf("There is no rank on CS0 for controller %d.\n", ctrl_num); 838 popts->memctl_interleaving = 0; 839 goto done; 840 } 841 popts->memctl_interleaving = 1; 842 #ifdef CONFIG_SYS_FSL_DDR_INTLV_256B 843 popts->memctl_interleaving_mode = FSL_DDR_256B_INTERLEAVING; 844 popts->memctl_interleaving = 1; 845 debug("256 Byte interleaving\n"); 846 goto done; 847 #endif 848 /* 849 * test null first. if CONFIG_HWCONFIG is not defined 850 * hwconfig_arg_cmp returns non-zero 851 */ 852 if (hwconfig_subarg_cmp_f("fsl_ddr", "ctlr_intlv", 853 "null", buf)) { 854 popts->memctl_interleaving = 0; 855 debug("memory controller interleaving disabled.\n"); 856 } else if (hwconfig_subarg_cmp_f("fsl_ddr", 857 "ctlr_intlv", 858 "cacheline", buf)) { 859 popts->memctl_interleaving_mode = 860 ((CONFIG_NUM_DDR_CONTROLLERS == 3) && ctrl_num == 2) ? 861 0 : FSL_DDR_CACHE_LINE_INTERLEAVING; 862 popts->memctl_interleaving = 863 ((CONFIG_NUM_DDR_CONTROLLERS == 3) && ctrl_num == 2) ? 864 0 : 1; 865 } else if (hwconfig_subarg_cmp_f("fsl_ddr", 866 "ctlr_intlv", 867 "page", buf)) { 868 popts->memctl_interleaving_mode = 869 ((CONFIG_NUM_DDR_CONTROLLERS == 3) && ctrl_num == 2) ? 870 0 : FSL_DDR_PAGE_INTERLEAVING; 871 popts->memctl_interleaving = 872 ((CONFIG_NUM_DDR_CONTROLLERS == 3) && ctrl_num == 2) ? 873 0 : 1; 874 } else if (hwconfig_subarg_cmp_f("fsl_ddr", 875 "ctlr_intlv", 876 "bank", buf)) { 877 popts->memctl_interleaving_mode = 878 ((CONFIG_NUM_DDR_CONTROLLERS == 3) && ctrl_num == 2) ? 879 0 : FSL_DDR_BANK_INTERLEAVING; 880 popts->memctl_interleaving = 881 ((CONFIG_NUM_DDR_CONTROLLERS == 3) && ctrl_num == 2) ? 882 0 : 1; 883 } else if (hwconfig_subarg_cmp_f("fsl_ddr", 884 "ctlr_intlv", 885 "superbank", buf)) { 886 popts->memctl_interleaving_mode = 887 ((CONFIG_NUM_DDR_CONTROLLERS == 3) && ctrl_num == 2) ? 888 0 : FSL_DDR_SUPERBANK_INTERLEAVING; 889 popts->memctl_interleaving = 890 ((CONFIG_NUM_DDR_CONTROLLERS == 3) && ctrl_num == 2) ? 891 0 : 1; 892 #if (CONFIG_NUM_DDR_CONTROLLERS == 3) 893 } else if (hwconfig_subarg_cmp_f("fsl_ddr", 894 "ctlr_intlv", 895 "3way_1KB", buf)) { 896 popts->memctl_interleaving_mode = 897 FSL_DDR_3WAY_1KB_INTERLEAVING; 898 } else if (hwconfig_subarg_cmp_f("fsl_ddr", 899 "ctlr_intlv", 900 "3way_4KB", buf)) { 901 popts->memctl_interleaving_mode = 902 FSL_DDR_3WAY_4KB_INTERLEAVING; 903 } else if (hwconfig_subarg_cmp_f("fsl_ddr", 904 "ctlr_intlv", 905 "3way_8KB", buf)) { 906 popts->memctl_interleaving_mode = 907 FSL_DDR_3WAY_8KB_INTERLEAVING; 908 #elif (CONFIG_NUM_DDR_CONTROLLERS == 4) 909 } else if (hwconfig_subarg_cmp_f("fsl_ddr", 910 "ctlr_intlv", 911 "4way_1KB", buf)) { 912 popts->memctl_interleaving_mode = 913 FSL_DDR_4WAY_1KB_INTERLEAVING; 914 } else if (hwconfig_subarg_cmp_f("fsl_ddr", 915 "ctlr_intlv", 916 "4way_4KB", buf)) { 917 popts->memctl_interleaving_mode = 918 FSL_DDR_4WAY_4KB_INTERLEAVING; 919 } else if (hwconfig_subarg_cmp_f("fsl_ddr", 920 "ctlr_intlv", 921 "4way_8KB", buf)) { 922 popts->memctl_interleaving_mode = 923 FSL_DDR_4WAY_8KB_INTERLEAVING; 924 #endif 925 } else { 926 popts->memctl_interleaving = 0; 927 printf("hwconfig has unrecognized parameter for ctlr_intlv.\n"); 928 } 929 done: 930 #endif 931 if ((hwconfig_sub_f("fsl_ddr", "bank_intlv", buf)) && 932 (CONFIG_CHIP_SELECTS_PER_CTRL > 1)) { 933 /* test null first. if CONFIG_HWCONFIG is not defined, 934 * hwconfig_subarg_cmp_f returns non-zero */ 935 if (hwconfig_subarg_cmp_f("fsl_ddr", "bank_intlv", 936 "null", buf)) 937 debug("bank interleaving disabled.\n"); 938 else if (hwconfig_subarg_cmp_f("fsl_ddr", "bank_intlv", 939 "cs0_cs1", buf)) 940 popts->ba_intlv_ctl = FSL_DDR_CS0_CS1; 941 else if (hwconfig_subarg_cmp_f("fsl_ddr", "bank_intlv", 942 "cs2_cs3", buf)) 943 popts->ba_intlv_ctl = FSL_DDR_CS2_CS3; 944 else if (hwconfig_subarg_cmp_f("fsl_ddr", "bank_intlv", 945 "cs0_cs1_and_cs2_cs3", buf)) 946 popts->ba_intlv_ctl = FSL_DDR_CS0_CS1_AND_CS2_CS3; 947 else if (hwconfig_subarg_cmp_f("fsl_ddr", "bank_intlv", 948 "cs0_cs1_cs2_cs3", buf)) 949 popts->ba_intlv_ctl = FSL_DDR_CS0_CS1_CS2_CS3; 950 else if (hwconfig_subarg_cmp_f("fsl_ddr", "bank_intlv", 951 "auto", buf)) 952 popts->ba_intlv_ctl = auto_bank_intlv(pdimm); 953 else 954 printf("hwconfig has unrecognized parameter for bank_intlv.\n"); 955 switch (popts->ba_intlv_ctl & FSL_DDR_CS0_CS1_CS2_CS3) { 956 case FSL_DDR_CS0_CS1_CS2_CS3: 957 #if (CONFIG_DIMM_SLOTS_PER_CTLR == 1) 958 if (pdimm[0].n_ranks < 4) { 959 popts->ba_intlv_ctl = 0; 960 printf("Not enough bank(chip-select) for " 961 "CS0+CS1+CS2+CS3 on controller %d, " 962 "interleaving disabled!\n", ctrl_num); 963 } 964 #elif (CONFIG_DIMM_SLOTS_PER_CTLR == 2) 965 #ifdef CONFIG_FSL_DDR_FIRST_SLOT_QUAD_CAPABLE 966 if (pdimm[0].n_ranks == 4) 967 break; 968 #endif 969 if ((pdimm[0].n_ranks < 2) && (pdimm[1].n_ranks < 2)) { 970 popts->ba_intlv_ctl = 0; 971 printf("Not enough bank(chip-select) for " 972 "CS0+CS1+CS2+CS3 on controller %d, " 973 "interleaving disabled!\n", ctrl_num); 974 } 975 if (pdimm[0].capacity != pdimm[1].capacity) { 976 popts->ba_intlv_ctl = 0; 977 printf("Not identical DIMM size for " 978 "CS0+CS1+CS2+CS3 on controller %d, " 979 "interleaving disabled!\n", ctrl_num); 980 } 981 #endif 982 break; 983 case FSL_DDR_CS0_CS1: 984 if (pdimm[0].n_ranks < 2) { 985 popts->ba_intlv_ctl = 0; 986 printf("Not enough bank(chip-select) for " 987 "CS0+CS1 on controller %d, " 988 "interleaving disabled!\n", ctrl_num); 989 } 990 break; 991 case FSL_DDR_CS2_CS3: 992 #if (CONFIG_DIMM_SLOTS_PER_CTLR == 1) 993 if (pdimm[0].n_ranks < 4) { 994 popts->ba_intlv_ctl = 0; 995 printf("Not enough bank(chip-select) for CS2+CS3 " 996 "on controller %d, interleaving disabled!\n", ctrl_num); 997 } 998 #elif (CONFIG_DIMM_SLOTS_PER_CTLR == 2) 999 if (pdimm[1].n_ranks < 2) { 1000 popts->ba_intlv_ctl = 0; 1001 printf("Not enough bank(chip-select) for CS2+CS3 " 1002 "on controller %d, interleaving disabled!\n", ctrl_num); 1003 } 1004 #endif 1005 break; 1006 case FSL_DDR_CS0_CS1_AND_CS2_CS3: 1007 #if (CONFIG_DIMM_SLOTS_PER_CTLR == 1) 1008 if (pdimm[0].n_ranks < 4) { 1009 popts->ba_intlv_ctl = 0; 1010 printf("Not enough bank(CS) for CS0+CS1 and " 1011 "CS2+CS3 on controller %d, " 1012 "interleaving disabled!\n", ctrl_num); 1013 } 1014 #elif (CONFIG_DIMM_SLOTS_PER_CTLR == 2) 1015 if ((pdimm[0].n_ranks < 2) || (pdimm[1].n_ranks < 2)) { 1016 popts->ba_intlv_ctl = 0; 1017 printf("Not enough bank(CS) for CS0+CS1 and " 1018 "CS2+CS3 on controller %d, " 1019 "interleaving disabled!\n", ctrl_num); 1020 } 1021 #endif 1022 break; 1023 default: 1024 popts->ba_intlv_ctl = 0; 1025 break; 1026 } 1027 } 1028 1029 if (hwconfig_sub_f("fsl_ddr", "addr_hash", buf)) { 1030 if (hwconfig_subarg_cmp_f("fsl_ddr", "addr_hash", "null", buf)) 1031 popts->addr_hash = 0; 1032 else if (hwconfig_subarg_cmp_f("fsl_ddr", "addr_hash", 1033 "true", buf)) 1034 popts->addr_hash = 1; 1035 } 1036 1037 if (pdimm[0].n_ranks == 4) 1038 popts->quad_rank_present = 1; 1039 1040 ddr_freq = get_ddr_freq(0) / 1000000; 1041 if (popts->registered_dimm_en) { 1042 popts->rcw_override = 1; 1043 popts->rcw_1 = 0x000a5a00; 1044 if (ddr_freq <= 800) 1045 popts->rcw_2 = 0x00000000; 1046 else if (ddr_freq <= 1066) 1047 popts->rcw_2 = 0x00100000; 1048 else if (ddr_freq <= 1333) 1049 popts->rcw_2 = 0x00200000; 1050 else 1051 popts->rcw_2 = 0x00300000; 1052 } 1053 1054 fsl_ddr_board_options(popts, pdimm, ctrl_num); 1055 1056 return 0; 1057 } 1058 1059 void check_interleaving_options(fsl_ddr_info_t *pinfo) 1060 { 1061 int i, j, k, check_n_ranks, intlv_invalid = 0; 1062 unsigned int check_intlv, check_n_row_addr, check_n_col_addr; 1063 unsigned long long check_rank_density; 1064 struct dimm_params_s *dimm; 1065 /* 1066 * Check if all controllers are configured for memory 1067 * controller interleaving. Identical dimms are recommended. At least 1068 * the size, row and col address should be checked. 1069 */ 1070 j = 0; 1071 check_n_ranks = pinfo->dimm_params[0][0].n_ranks; 1072 check_rank_density = pinfo->dimm_params[0][0].rank_density; 1073 check_n_row_addr = pinfo->dimm_params[0][0].n_row_addr; 1074 check_n_col_addr = pinfo->dimm_params[0][0].n_col_addr; 1075 check_intlv = pinfo->memctl_opts[0].memctl_interleaving_mode; 1076 for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) { 1077 dimm = &pinfo->dimm_params[i][0]; 1078 if (!pinfo->memctl_opts[i].memctl_interleaving) { 1079 continue; 1080 } else if (((check_rank_density != dimm->rank_density) || 1081 (check_n_ranks != dimm->n_ranks) || 1082 (check_n_row_addr != dimm->n_row_addr) || 1083 (check_n_col_addr != dimm->n_col_addr) || 1084 (check_intlv != 1085 pinfo->memctl_opts[i].memctl_interleaving_mode))){ 1086 intlv_invalid = 1; 1087 break; 1088 } else { 1089 j++; 1090 } 1091 1092 } 1093 if (intlv_invalid) { 1094 for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) 1095 pinfo->memctl_opts[i].memctl_interleaving = 0; 1096 printf("Not all DIMMs are identical. " 1097 "Memory controller interleaving disabled.\n"); 1098 } else { 1099 switch (check_intlv) { 1100 case FSL_DDR_256B_INTERLEAVING: 1101 case FSL_DDR_CACHE_LINE_INTERLEAVING: 1102 case FSL_DDR_PAGE_INTERLEAVING: 1103 case FSL_DDR_BANK_INTERLEAVING: 1104 case FSL_DDR_SUPERBANK_INTERLEAVING: 1105 if (3 == CONFIG_NUM_DDR_CONTROLLERS) 1106 k = 2; 1107 else 1108 k = CONFIG_NUM_DDR_CONTROLLERS; 1109 break; 1110 case FSL_DDR_3WAY_1KB_INTERLEAVING: 1111 case FSL_DDR_3WAY_4KB_INTERLEAVING: 1112 case FSL_DDR_3WAY_8KB_INTERLEAVING: 1113 case FSL_DDR_4WAY_1KB_INTERLEAVING: 1114 case FSL_DDR_4WAY_4KB_INTERLEAVING: 1115 case FSL_DDR_4WAY_8KB_INTERLEAVING: 1116 default: 1117 k = CONFIG_NUM_DDR_CONTROLLERS; 1118 break; 1119 } 1120 debug("%d of %d controllers are interleaving.\n", j, k); 1121 if (j && (j != k)) { 1122 for (i = 0; i < CONFIG_NUM_DDR_CONTROLLERS; i++) 1123 pinfo->memctl_opts[i].memctl_interleaving = 0; 1124 printf("Not all controllers have compatible " 1125 "interleaving mode. All disabled.\n"); 1126 } 1127 } 1128 debug("Checking interleaving options completed\n"); 1129 } 1130 1131 int fsl_use_spd(void) 1132 { 1133 int use_spd = 0; 1134 1135 #ifdef CONFIG_DDR_SPD 1136 char buffer[HWCONFIG_BUFFER_SIZE]; 1137 char *buf = NULL; 1138 1139 /* 1140 * Extract hwconfig from environment since we have not properly setup 1141 * the environment but need it for ddr config params 1142 */ 1143 if (getenv_f("hwconfig", buffer, sizeof(buffer)) > 0) 1144 buf = buffer; 1145 1146 /* if hwconfig is not enabled, or "sdram" is not defined, use spd */ 1147 if (hwconfig_sub_f("fsl_ddr", "sdram", buf)) { 1148 if (hwconfig_subarg_cmp_f("fsl_ddr", "sdram", "spd", buf)) 1149 use_spd = 1; 1150 else if (hwconfig_subarg_cmp_f("fsl_ddr", "sdram", 1151 "fixed", buf)) 1152 use_spd = 0; 1153 else 1154 use_spd = 1; 1155 } else 1156 use_spd = 1; 1157 #endif 1158 1159 return use_spd; 1160 } 1161