1 /* 2 * Copyright 2008-2014 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0 5 */ 6 7 /* 8 * Generic driver for Freescale DDR/DDR2/DDR3 memory controller. 9 * Based on code from spd_sdram.c 10 * Author: James Yang [at freescale.com] 11 */ 12 13 #include <common.h> 14 #include <i2c.h> 15 #include <fsl_ddr_sdram.h> 16 #include <fsl_ddr.h> 17 18 /* 19 * CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY is the physical address from the view 20 * of DDR controllers. It is the same as CONFIG_SYS_DDR_SDRAM_BASE for 21 * all Power SoCs. But it could be different for ARM SoCs. For example, 22 * fsl_lsch3 has a mapping mechanism to map DDR memory to ranges (in order) of 23 * 0x00_8000_0000 ~ 0x00_ffff_ffff 24 * 0x80_8000_0000 ~ 0xff_ffff_ffff 25 */ 26 #ifndef CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 27 #define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY CONFIG_SYS_DDR_SDRAM_BASE 28 #endif 29 30 #ifdef CONFIG_PPC 31 #include <asm/fsl_law.h> 32 33 void fsl_ddr_set_lawbar( 34 const common_timing_params_t *memctl_common_params, 35 unsigned int memctl_interleaved, 36 unsigned int ctrl_num); 37 #endif 38 39 void fsl_ddr_set_intl3r(const unsigned int granule_size); 40 #if defined(SPD_EEPROM_ADDRESS) || \ 41 defined(SPD_EEPROM_ADDRESS1) || defined(SPD_EEPROM_ADDRESS2) || \ 42 defined(SPD_EEPROM_ADDRESS3) || defined(SPD_EEPROM_ADDRESS4) 43 #if (CONFIG_NUM_DDR_CONTROLLERS == 1) && (CONFIG_DIMM_SLOTS_PER_CTLR == 1) 44 u8 spd_i2c_addr[CONFIG_NUM_DDR_CONTROLLERS][CONFIG_DIMM_SLOTS_PER_CTLR] = { 45 [0][0] = SPD_EEPROM_ADDRESS, 46 }; 47 #elif (CONFIG_NUM_DDR_CONTROLLERS == 1) && (CONFIG_DIMM_SLOTS_PER_CTLR == 2) 48 u8 spd_i2c_addr[CONFIG_NUM_DDR_CONTROLLERS][CONFIG_DIMM_SLOTS_PER_CTLR] = { 49 [0][0] = SPD_EEPROM_ADDRESS1, /* controller 1 */ 50 [0][1] = SPD_EEPROM_ADDRESS2, /* controller 1 */ 51 }; 52 #elif (CONFIG_NUM_DDR_CONTROLLERS == 2) && (CONFIG_DIMM_SLOTS_PER_CTLR == 1) 53 u8 spd_i2c_addr[CONFIG_NUM_DDR_CONTROLLERS][CONFIG_DIMM_SLOTS_PER_CTLR] = { 54 [0][0] = SPD_EEPROM_ADDRESS1, /* controller 1 */ 55 [1][0] = SPD_EEPROM_ADDRESS2, /* controller 2 */ 56 }; 57 #elif (CONFIG_NUM_DDR_CONTROLLERS == 2) && (CONFIG_DIMM_SLOTS_PER_CTLR == 2) 58 u8 spd_i2c_addr[CONFIG_NUM_DDR_CONTROLLERS][CONFIG_DIMM_SLOTS_PER_CTLR] = { 59 [0][0] = SPD_EEPROM_ADDRESS1, /* controller 1 */ 60 [0][1] = SPD_EEPROM_ADDRESS2, /* controller 1 */ 61 [1][0] = SPD_EEPROM_ADDRESS3, /* controller 2 */ 62 [1][1] = SPD_EEPROM_ADDRESS4, /* controller 2 */ 63 }; 64 #elif (CONFIG_NUM_DDR_CONTROLLERS == 3) && (CONFIG_DIMM_SLOTS_PER_CTLR == 1) 65 u8 spd_i2c_addr[CONFIG_NUM_DDR_CONTROLLERS][CONFIG_DIMM_SLOTS_PER_CTLR] = { 66 [0][0] = SPD_EEPROM_ADDRESS1, /* controller 1 */ 67 [1][0] = SPD_EEPROM_ADDRESS2, /* controller 2 */ 68 [2][0] = SPD_EEPROM_ADDRESS3, /* controller 3 */ 69 }; 70 #elif (CONFIG_NUM_DDR_CONTROLLERS == 3) && (CONFIG_DIMM_SLOTS_PER_CTLR == 2) 71 u8 spd_i2c_addr[CONFIG_NUM_DDR_CONTROLLERS][CONFIG_DIMM_SLOTS_PER_CTLR] = { 72 [0][0] = SPD_EEPROM_ADDRESS1, /* controller 1 */ 73 [0][1] = SPD_EEPROM_ADDRESS2, /* controller 1 */ 74 [1][0] = SPD_EEPROM_ADDRESS3, /* controller 2 */ 75 [1][1] = SPD_EEPROM_ADDRESS4, /* controller 2 */ 76 [2][0] = SPD_EEPROM_ADDRESS5, /* controller 3 */ 77 [2][1] = SPD_EEPROM_ADDRESS6, /* controller 3 */ 78 }; 79 80 #endif 81 82 #define SPD_SPA0_ADDRESS 0x36 83 #define SPD_SPA1_ADDRESS 0x37 84 85 static void __get_spd(generic_spd_eeprom_t *spd, u8 i2c_address) 86 { 87 int ret; 88 #ifdef CONFIG_SYS_FSL_DDR4 89 uint8_t dummy = 0; 90 #endif 91 92 i2c_set_bus_num(CONFIG_SYS_SPD_BUS_NUM); 93 94 #ifdef CONFIG_SYS_FSL_DDR4 95 /* 96 * DDR4 SPD has 384 to 512 bytes 97 * To access the lower 256 bytes, we need to set EE page address to 0 98 * To access the upper 256 bytes, we need to set EE page address to 1 99 * See Jedec standar No. 21-C for detail 100 */ 101 i2c_write(SPD_SPA0_ADDRESS, 0, 1, &dummy, 1); 102 ret = i2c_read(i2c_address, 0, 1, (uchar *)spd, 256); 103 if (!ret) { 104 i2c_write(SPD_SPA1_ADDRESS, 0, 1, &dummy, 1); 105 ret = i2c_read(i2c_address, 0, 1, 106 (uchar *)((ulong)spd + 256), 107 min(256, 108 (int)sizeof(generic_spd_eeprom_t) - 256)); 109 } 110 #else 111 ret = i2c_read(i2c_address, 0, 1, (uchar *)spd, 112 sizeof(generic_spd_eeprom_t)); 113 #endif 114 115 if (ret) { 116 if (i2c_address == 117 #ifdef SPD_EEPROM_ADDRESS 118 SPD_EEPROM_ADDRESS 119 #elif defined(SPD_EEPROM_ADDRESS1) 120 SPD_EEPROM_ADDRESS1 121 #endif 122 ) { 123 printf("DDR: failed to read SPD from address %u\n", 124 i2c_address); 125 } else { 126 debug("DDR: failed to read SPD from address %u\n", 127 i2c_address); 128 } 129 memset(spd, 0, sizeof(generic_spd_eeprom_t)); 130 } 131 } 132 133 __attribute__((weak, alias("__get_spd"))) 134 void get_spd(generic_spd_eeprom_t *spd, u8 i2c_address); 135 136 /* This function allows boards to update SPD address */ 137 __weak void update_spd_address(unsigned int ctrl_num, 138 unsigned int slot, 139 unsigned int *addr) 140 { 141 } 142 143 void fsl_ddr_get_spd(generic_spd_eeprom_t *ctrl_dimms_spd, 144 unsigned int ctrl_num, unsigned int dimm_slots_per_ctrl) 145 { 146 unsigned int i; 147 unsigned int i2c_address = 0; 148 149 if (ctrl_num >= CONFIG_NUM_DDR_CONTROLLERS) { 150 printf("%s unexpected ctrl_num = %u\n", __FUNCTION__, ctrl_num); 151 return; 152 } 153 154 for (i = 0; i < dimm_slots_per_ctrl; i++) { 155 i2c_address = spd_i2c_addr[ctrl_num][i]; 156 update_spd_address(ctrl_num, i, &i2c_address); 157 get_spd(&(ctrl_dimms_spd[i]), i2c_address); 158 } 159 } 160 #else 161 void fsl_ddr_get_spd(generic_spd_eeprom_t *ctrl_dimms_spd, 162 unsigned int ctrl_num, unsigned int dimm_slots_per_ctrl) 163 { 164 } 165 #endif /* SPD_EEPROM_ADDRESSx */ 166 167 /* 168 * ASSUMPTIONS: 169 * - Same number of CONFIG_DIMM_SLOTS_PER_CTLR on each controller 170 * - Same memory data bus width on all controllers 171 * 172 * NOTES: 173 * 174 * The memory controller and associated documentation use confusing 175 * terminology when referring to the orgranization of DRAM. 176 * 177 * Here is a terminology translation table: 178 * 179 * memory controller/documention |industry |this code |signals 180 * -------------------------------|-----------|-----------|----------------- 181 * physical bank/bank |rank |rank |chip select (CS) 182 * logical bank/sub-bank |bank |bank |bank address (BA) 183 * page/row |row |page |row address 184 * ??? |column |column |column address 185 * 186 * The naming confusion is further exacerbated by the descriptions of the 187 * memory controller interleaving feature, where accesses are interleaved 188 * _BETWEEN_ two seperate memory controllers. This is configured only in 189 * CS0_CONFIG[INTLV_CTL] of each memory controller. 190 * 191 * memory controller documentation | number of chip selects 192 * | per memory controller supported 193 * --------------------------------|----------------------------------------- 194 * cache line interleaving | 1 (CS0 only) 195 * page interleaving | 1 (CS0 only) 196 * bank interleaving | 1 (CS0 only) 197 * superbank interleraving | depends on bank (chip select) 198 * | interleraving [rank interleaving] 199 * | mode used on every memory controller 200 * 201 * Even further confusing is the existence of the interleaving feature 202 * _WITHIN_ each memory controller. The feature is referred to in 203 * documentation as chip select interleaving or bank interleaving, 204 * although it is configured in the DDR_SDRAM_CFG field. 205 * 206 * Name of field | documentation name | this code 207 * -----------------------------|-----------------------|------------------ 208 * DDR_SDRAM_CFG[BA_INTLV_CTL] | Bank (chip select) | rank interleaving 209 * | interleaving 210 */ 211 212 const char *step_string_tbl[] = { 213 "STEP_GET_SPD", 214 "STEP_COMPUTE_DIMM_PARMS", 215 "STEP_COMPUTE_COMMON_PARMS", 216 "STEP_GATHER_OPTS", 217 "STEP_ASSIGN_ADDRESSES", 218 "STEP_COMPUTE_REGS", 219 "STEP_PROGRAM_REGS", 220 "STEP_ALL" 221 }; 222 223 const char * step_to_string(unsigned int step) { 224 225 unsigned int s = __ilog2(step); 226 227 if ((1 << s) != step) 228 return step_string_tbl[7]; 229 230 if (s >= ARRAY_SIZE(step_string_tbl)) { 231 printf("Error for the step in %s\n", __func__); 232 s = 0; 233 } 234 235 return step_string_tbl[s]; 236 } 237 238 static unsigned long long __step_assign_addresses(fsl_ddr_info_t *pinfo, 239 unsigned int dbw_cap_adj[]) 240 { 241 unsigned int i, j; 242 unsigned long long total_mem, current_mem_base, total_ctlr_mem; 243 unsigned long long rank_density, ctlr_density = 0; 244 unsigned int first_ctrl = pinfo->first_ctrl; 245 unsigned int last_ctrl = first_ctrl + pinfo->num_ctrls - 1; 246 247 /* 248 * If a reduced data width is requested, but the SPD 249 * specifies a physically wider device, adjust the 250 * computed dimm capacities accordingly before 251 * assigning addresses. 252 */ 253 for (i = first_ctrl; i <= last_ctrl; i++) { 254 unsigned int found = 0; 255 256 switch (pinfo->memctl_opts[i].data_bus_width) { 257 case 2: 258 /* 16-bit */ 259 for (j = 0; j < CONFIG_DIMM_SLOTS_PER_CTLR; j++) { 260 unsigned int dw; 261 if (!pinfo->dimm_params[i][j].n_ranks) 262 continue; 263 dw = pinfo->dimm_params[i][j].primary_sdram_width; 264 if ((dw == 72 || dw == 64)) { 265 dbw_cap_adj[i] = 2; 266 break; 267 } else if ((dw == 40 || dw == 32)) { 268 dbw_cap_adj[i] = 1; 269 break; 270 } 271 } 272 break; 273 274 case 1: 275 /* 32-bit */ 276 for (j = 0; j < CONFIG_DIMM_SLOTS_PER_CTLR; j++) { 277 unsigned int dw; 278 dw = pinfo->dimm_params[i][j].data_width; 279 if (pinfo->dimm_params[i][j].n_ranks 280 && (dw == 72 || dw == 64)) { 281 /* 282 * FIXME: can't really do it 283 * like this because this just 284 * further reduces the memory 285 */ 286 found = 1; 287 break; 288 } 289 } 290 if (found) { 291 dbw_cap_adj[i] = 1; 292 } 293 break; 294 295 case 0: 296 /* 64-bit */ 297 break; 298 299 default: 300 printf("unexpected data bus width " 301 "specified controller %u\n", i); 302 return 1; 303 } 304 debug("dbw_cap_adj[%d]=%d\n", i, dbw_cap_adj[i]); 305 } 306 307 current_mem_base = pinfo->mem_base; 308 total_mem = 0; 309 if (pinfo->memctl_opts[first_ctrl].memctl_interleaving) { 310 rank_density = pinfo->dimm_params[first_ctrl][0].rank_density >> 311 dbw_cap_adj[first_ctrl]; 312 switch (pinfo->memctl_opts[first_ctrl].ba_intlv_ctl & 313 FSL_DDR_CS0_CS1_CS2_CS3) { 314 case FSL_DDR_CS0_CS1_CS2_CS3: 315 ctlr_density = 4 * rank_density; 316 break; 317 case FSL_DDR_CS0_CS1: 318 case FSL_DDR_CS0_CS1_AND_CS2_CS3: 319 ctlr_density = 2 * rank_density; 320 break; 321 case FSL_DDR_CS2_CS3: 322 default: 323 ctlr_density = rank_density; 324 break; 325 } 326 debug("rank density is 0x%llx, ctlr density is 0x%llx\n", 327 rank_density, ctlr_density); 328 for (i = first_ctrl; i <= last_ctrl; i++) { 329 if (pinfo->memctl_opts[i].memctl_interleaving) { 330 switch (pinfo->memctl_opts[i].memctl_interleaving_mode) { 331 case FSL_DDR_256B_INTERLEAVING: 332 case FSL_DDR_CACHE_LINE_INTERLEAVING: 333 case FSL_DDR_PAGE_INTERLEAVING: 334 case FSL_DDR_BANK_INTERLEAVING: 335 case FSL_DDR_SUPERBANK_INTERLEAVING: 336 total_ctlr_mem = 2 * ctlr_density; 337 break; 338 case FSL_DDR_3WAY_1KB_INTERLEAVING: 339 case FSL_DDR_3WAY_4KB_INTERLEAVING: 340 case FSL_DDR_3WAY_8KB_INTERLEAVING: 341 total_ctlr_mem = 3 * ctlr_density; 342 break; 343 case FSL_DDR_4WAY_1KB_INTERLEAVING: 344 case FSL_DDR_4WAY_4KB_INTERLEAVING: 345 case FSL_DDR_4WAY_8KB_INTERLEAVING: 346 total_ctlr_mem = 4 * ctlr_density; 347 break; 348 default: 349 panic("Unknown interleaving mode"); 350 } 351 pinfo->common_timing_params[i].base_address = 352 current_mem_base; 353 pinfo->common_timing_params[i].total_mem = 354 total_ctlr_mem; 355 total_mem = current_mem_base + total_ctlr_mem; 356 debug("ctrl %d base 0x%llx\n", i, current_mem_base); 357 debug("ctrl %d total 0x%llx\n", i, total_ctlr_mem); 358 } else { 359 /* when 3rd controller not interleaved */ 360 current_mem_base = total_mem; 361 total_ctlr_mem = 0; 362 pinfo->common_timing_params[i].base_address = 363 current_mem_base; 364 for (j = 0; j < CONFIG_DIMM_SLOTS_PER_CTLR; j++) { 365 unsigned long long cap = 366 pinfo->dimm_params[i][j].capacity >> dbw_cap_adj[i]; 367 pinfo->dimm_params[i][j].base_address = 368 current_mem_base; 369 debug("ctrl %d dimm %d base 0x%llx\n", i, j, current_mem_base); 370 current_mem_base += cap; 371 total_ctlr_mem += cap; 372 } 373 debug("ctrl %d total 0x%llx\n", i, total_ctlr_mem); 374 pinfo->common_timing_params[i].total_mem = 375 total_ctlr_mem; 376 total_mem += total_ctlr_mem; 377 } 378 } 379 } else { 380 /* 381 * Simple linear assignment if memory 382 * controllers are not interleaved. 383 */ 384 for (i = first_ctrl; i <= last_ctrl; i++) { 385 total_ctlr_mem = 0; 386 pinfo->common_timing_params[i].base_address = 387 current_mem_base; 388 for (j = 0; j < CONFIG_DIMM_SLOTS_PER_CTLR; j++) { 389 /* Compute DIMM base addresses. */ 390 unsigned long long cap = 391 pinfo->dimm_params[i][j].capacity >> dbw_cap_adj[i]; 392 pinfo->dimm_params[i][j].base_address = 393 current_mem_base; 394 debug("ctrl %d dimm %d base 0x%llx\n", i, j, current_mem_base); 395 current_mem_base += cap; 396 total_ctlr_mem += cap; 397 } 398 debug("ctrl %d total 0x%llx\n", i, total_ctlr_mem); 399 pinfo->common_timing_params[i].total_mem = 400 total_ctlr_mem; 401 total_mem += total_ctlr_mem; 402 } 403 } 404 debug("Total mem by %s is 0x%llx\n", __func__, total_mem); 405 406 return total_mem; 407 } 408 409 /* Use weak function to allow board file to override the address assignment */ 410 __attribute__((weak, alias("__step_assign_addresses"))) 411 unsigned long long step_assign_addresses(fsl_ddr_info_t *pinfo, 412 unsigned int dbw_cap_adj[]); 413 414 unsigned long long 415 fsl_ddr_compute(fsl_ddr_info_t *pinfo, unsigned int start_step, 416 unsigned int size_only) 417 { 418 unsigned int i, j; 419 unsigned long long total_mem = 0; 420 int assert_reset = 0; 421 unsigned int first_ctrl = pinfo->first_ctrl; 422 unsigned int last_ctrl = first_ctrl + pinfo->num_ctrls - 1; 423 __maybe_unused int retval; 424 __maybe_unused bool goodspd = false; 425 __maybe_unused int dimm_slots_per_ctrl = pinfo->dimm_slots_per_ctrl; 426 427 fsl_ddr_cfg_regs_t *ddr_reg = pinfo->fsl_ddr_config_reg; 428 common_timing_params_t *timing_params = pinfo->common_timing_params; 429 if (pinfo->board_need_mem_reset) 430 assert_reset = pinfo->board_need_mem_reset(); 431 432 /* data bus width capacity adjust shift amount */ 433 unsigned int dbw_capacity_adjust[CONFIG_NUM_DDR_CONTROLLERS]; 434 435 for (i = first_ctrl; i <= last_ctrl; i++) 436 dbw_capacity_adjust[i] = 0; 437 438 debug("starting at step %u (%s)\n", 439 start_step, step_to_string(start_step)); 440 441 switch (start_step) { 442 case STEP_GET_SPD: 443 #if defined(CONFIG_DDR_SPD) || defined(CONFIG_SPD_EEPROM) 444 /* STEP 1: Gather all DIMM SPD data */ 445 for (i = first_ctrl; i <= last_ctrl; i++) { 446 fsl_ddr_get_spd(pinfo->spd_installed_dimms[i], i, 447 dimm_slots_per_ctrl); 448 } 449 450 case STEP_COMPUTE_DIMM_PARMS: 451 /* STEP 2: Compute DIMM parameters from SPD data */ 452 453 for (i = first_ctrl; i <= last_ctrl; i++) { 454 for (j = 0; j < CONFIG_DIMM_SLOTS_PER_CTLR; j++) { 455 generic_spd_eeprom_t *spd = 456 &(pinfo->spd_installed_dimms[i][j]); 457 dimm_params_t *pdimm = 458 &(pinfo->dimm_params[i][j]); 459 retval = compute_dimm_parameters( 460 i, spd, pdimm, j); 461 #ifdef CONFIG_SYS_DDR_RAW_TIMING 462 if (!j && retval) { 463 printf("SPD error on controller %d! " 464 "Trying fallback to raw timing " 465 "calculation\n", i); 466 retval = fsl_ddr_get_dimm_params(pdimm, 467 i, j); 468 } 469 #else 470 if (retval == 2) { 471 printf("Error: compute_dimm_parameters" 472 " non-zero returned FATAL value " 473 "for memctl=%u dimm=%u\n", i, j); 474 return 0; 475 } 476 #endif 477 if (retval) { 478 debug("Warning: compute_dimm_parameters" 479 " non-zero return value for memctl=%u " 480 "dimm=%u\n", i, j); 481 } else { 482 goodspd = true; 483 } 484 } 485 } 486 if (!goodspd) { 487 /* 488 * No valid SPD found 489 * Throw an error if this is for main memory, i.e. 490 * first_ctrl == 0. Otherwise, siliently return 0 491 * as the memory size. 492 */ 493 if (first_ctrl == 0) 494 printf("Error: No valid SPD detected.\n"); 495 496 return 0; 497 } 498 #elif defined(CONFIG_SYS_DDR_RAW_TIMING) 499 case STEP_COMPUTE_DIMM_PARMS: 500 for (i = first_ctrl; i <= last_ctrl; i++) { 501 for (j = 0; j < CONFIG_DIMM_SLOTS_PER_CTLR; j++) { 502 dimm_params_t *pdimm = 503 &(pinfo->dimm_params[i][j]); 504 fsl_ddr_get_dimm_params(pdimm, i, j); 505 } 506 } 507 debug("Filling dimm parameters from board specific file\n"); 508 #endif 509 case STEP_COMPUTE_COMMON_PARMS: 510 /* 511 * STEP 3: Compute a common set of timing parameters 512 * suitable for all of the DIMMs on each memory controller 513 */ 514 for (i = first_ctrl; i <= last_ctrl; i++) { 515 debug("Computing lowest common DIMM" 516 " parameters for memctl=%u\n", i); 517 compute_lowest_common_dimm_parameters 518 (i, 519 pinfo->dimm_params[i], 520 &timing_params[i], 521 CONFIG_DIMM_SLOTS_PER_CTLR); 522 } 523 524 case STEP_GATHER_OPTS: 525 /* STEP 4: Gather configuration requirements from user */ 526 for (i = first_ctrl; i <= last_ctrl; i++) { 527 debug("Reloading memory controller " 528 "configuration options for memctl=%u\n", i); 529 /* 530 * This "reloads" the memory controller options 531 * to defaults. If the user "edits" an option, 532 * next_step points to the step after this, 533 * which is currently STEP_ASSIGN_ADDRESSES. 534 */ 535 populate_memctl_options( 536 &timing_params[i], 537 &pinfo->memctl_opts[i], 538 pinfo->dimm_params[i], i); 539 /* 540 * For RDIMMs, JEDEC spec requires clocks to be stable 541 * before reset signal is deasserted. For the boards 542 * using fixed parameters, this function should be 543 * be called from board init file. 544 */ 545 if (timing_params[i].all_dimms_registered) 546 assert_reset = 1; 547 } 548 if (assert_reset && !size_only) { 549 if (pinfo->board_mem_reset) { 550 debug("Asserting mem reset\n"); 551 pinfo->board_mem_reset(); 552 } else { 553 debug("Asserting mem reset missing\n"); 554 } 555 } 556 557 case STEP_ASSIGN_ADDRESSES: 558 /* STEP 5: Assign addresses to chip selects */ 559 check_interleaving_options(pinfo); 560 total_mem = step_assign_addresses(pinfo, dbw_capacity_adjust); 561 debug("Total mem %llu assigned\n", total_mem); 562 563 case STEP_COMPUTE_REGS: 564 /* STEP 6: compute controller register values */ 565 debug("FSL Memory ctrl register computation\n"); 566 for (i = first_ctrl; i <= last_ctrl; i++) { 567 if (timing_params[i].ndimms_present == 0) { 568 memset(&ddr_reg[i], 0, 569 sizeof(fsl_ddr_cfg_regs_t)); 570 continue; 571 } 572 573 compute_fsl_memctl_config_regs 574 (i, 575 &pinfo->memctl_opts[i], 576 &ddr_reg[i], &timing_params[i], 577 pinfo->dimm_params[i], 578 dbw_capacity_adjust[i], 579 size_only); 580 } 581 582 default: 583 break; 584 } 585 586 { 587 /* 588 * Compute the amount of memory available just by 589 * looking for the highest valid CSn_BNDS value. 590 * This allows us to also experiment with using 591 * only CS0 when using dual-rank DIMMs. 592 */ 593 unsigned int max_end = 0; 594 595 for (i = first_ctrl; i <= last_ctrl; i++) { 596 for (j = 0; j < CONFIG_CHIP_SELECTS_PER_CTRL; j++) { 597 fsl_ddr_cfg_regs_t *reg = &ddr_reg[i]; 598 if (reg->cs[j].config & 0x80000000) { 599 unsigned int end; 600 /* 601 * 0xfffffff is a special value we put 602 * for unused bnds 603 */ 604 if (reg->cs[j].bnds == 0xffffffff) 605 continue; 606 end = reg->cs[j].bnds & 0xffff; 607 if (end > max_end) { 608 max_end = end; 609 } 610 } 611 } 612 } 613 614 total_mem = 1 + (((unsigned long long)max_end << 24ULL) | 615 0xFFFFFFULL) - pinfo->mem_base; 616 } 617 618 return total_mem; 619 } 620 621 phys_size_t __fsl_ddr_sdram(fsl_ddr_info_t *pinfo) 622 { 623 unsigned int i, first_ctrl, last_ctrl; 624 #ifdef CONFIG_PPC 625 unsigned int law_memctl = LAW_TRGT_IF_DDR_1; 626 #endif 627 unsigned long long total_memory; 628 int deassert_reset = 0; 629 630 first_ctrl = pinfo->first_ctrl; 631 last_ctrl = first_ctrl + pinfo->num_ctrls - 1; 632 633 /* Compute it once normally. */ 634 #ifdef CONFIG_FSL_DDR_INTERACTIVE 635 if (tstc() && (getc() == 'd')) { /* we got a key press of 'd' */ 636 total_memory = fsl_ddr_interactive(pinfo, 0); 637 } else if (fsl_ddr_interactive_env_var_exists()) { 638 total_memory = fsl_ddr_interactive(pinfo, 1); 639 } else 640 #endif 641 total_memory = fsl_ddr_compute(pinfo, STEP_GET_SPD, 0); 642 643 /* setup 3-way interleaving before enabling DDRC */ 644 switch (pinfo->memctl_opts[first_ctrl].memctl_interleaving_mode) { 645 case FSL_DDR_3WAY_1KB_INTERLEAVING: 646 case FSL_DDR_3WAY_4KB_INTERLEAVING: 647 case FSL_DDR_3WAY_8KB_INTERLEAVING: 648 fsl_ddr_set_intl3r( 649 pinfo->memctl_opts[first_ctrl]. 650 memctl_interleaving_mode); 651 break; 652 default: 653 break; 654 } 655 656 /* 657 * Program configuration registers. 658 * JEDEC specs requires clocks to be stable before deasserting reset 659 * for RDIMMs. Clocks start after chip select is enabled and clock 660 * control register is set. During step 1, all controllers have their 661 * registers set but not enabled. Step 2 proceeds after deasserting 662 * reset through board FPGA or GPIO. 663 * For non-registered DIMMs, initialization can go through but it is 664 * also OK to follow the same flow. 665 */ 666 if (pinfo->board_need_mem_reset) 667 deassert_reset = pinfo->board_need_mem_reset(); 668 for (i = first_ctrl; i <= last_ctrl; i++) { 669 if (pinfo->common_timing_params[i].all_dimms_registered) 670 deassert_reset = 1; 671 } 672 for (i = first_ctrl; i <= last_ctrl; i++) { 673 debug("Programming controller %u\n", i); 674 if (pinfo->common_timing_params[i].ndimms_present == 0) { 675 debug("No dimms present on controller %u; " 676 "skipping programming\n", i); 677 continue; 678 } 679 /* 680 * The following call with step = 1 returns before enabling 681 * the controller. It has to finish with step = 2 later. 682 */ 683 fsl_ddr_set_memctl_regs(&(pinfo->fsl_ddr_config_reg[i]), i, 684 deassert_reset ? 1 : 0); 685 } 686 if (deassert_reset) { 687 /* Use board FPGA or GPIO to deassert reset signal */ 688 if (pinfo->board_mem_de_reset) { 689 debug("Deasserting mem reset\n"); 690 pinfo->board_mem_de_reset(); 691 } else { 692 debug("Deasserting mem reset missing\n"); 693 } 694 for (i = first_ctrl; i <= last_ctrl; i++) { 695 /* Call with step = 2 to continue initialization */ 696 fsl_ddr_set_memctl_regs(&(pinfo->fsl_ddr_config_reg[i]), 697 i, 2); 698 } 699 } 700 701 #ifdef CONFIG_FSL_DDR_SYNC_REFRESH 702 fsl_ddr_sync_memctl_refresh(first_ctrl, last_ctrl); 703 #endif 704 705 #ifdef CONFIG_PPC 706 /* program LAWs */ 707 for (i = first_ctrl; i <= last_ctrl; i++) { 708 if (pinfo->memctl_opts[i].memctl_interleaving) { 709 switch (pinfo->memctl_opts[i]. 710 memctl_interleaving_mode) { 711 case FSL_DDR_CACHE_LINE_INTERLEAVING: 712 case FSL_DDR_PAGE_INTERLEAVING: 713 case FSL_DDR_BANK_INTERLEAVING: 714 case FSL_DDR_SUPERBANK_INTERLEAVING: 715 if (i % 2) 716 break; 717 if (i == 0) { 718 law_memctl = LAW_TRGT_IF_DDR_INTRLV; 719 fsl_ddr_set_lawbar( 720 &pinfo->common_timing_params[i], 721 law_memctl, i); 722 } 723 #if CONFIG_NUM_DDR_CONTROLLERS > 3 724 else if (i == 2) { 725 law_memctl = LAW_TRGT_IF_DDR_INTLV_34; 726 fsl_ddr_set_lawbar( 727 &pinfo->common_timing_params[i], 728 law_memctl, i); 729 } 730 #endif 731 break; 732 case FSL_DDR_3WAY_1KB_INTERLEAVING: 733 case FSL_DDR_3WAY_4KB_INTERLEAVING: 734 case FSL_DDR_3WAY_8KB_INTERLEAVING: 735 law_memctl = LAW_TRGT_IF_DDR_INTLV_123; 736 if (i == 0) { 737 fsl_ddr_set_lawbar( 738 &pinfo->common_timing_params[i], 739 law_memctl, i); 740 } 741 break; 742 case FSL_DDR_4WAY_1KB_INTERLEAVING: 743 case FSL_DDR_4WAY_4KB_INTERLEAVING: 744 case FSL_DDR_4WAY_8KB_INTERLEAVING: 745 law_memctl = LAW_TRGT_IF_DDR_INTLV_1234; 746 if (i == 0) 747 fsl_ddr_set_lawbar( 748 &pinfo->common_timing_params[i], 749 law_memctl, i); 750 /* place holder for future 4-way interleaving */ 751 break; 752 default: 753 break; 754 } 755 } else { 756 switch (i) { 757 case 0: 758 law_memctl = LAW_TRGT_IF_DDR_1; 759 break; 760 case 1: 761 law_memctl = LAW_TRGT_IF_DDR_2; 762 break; 763 case 2: 764 law_memctl = LAW_TRGT_IF_DDR_3; 765 break; 766 case 3: 767 law_memctl = LAW_TRGT_IF_DDR_4; 768 break; 769 default: 770 break; 771 } 772 fsl_ddr_set_lawbar(&pinfo->common_timing_params[i], 773 law_memctl, i); 774 } 775 } 776 #endif 777 778 debug("total_memory by %s = %llu\n", __func__, total_memory); 779 780 #if !defined(CONFIG_PHYS_64BIT) 781 /* Check for 4G or more. Bad. */ 782 if ((first_ctrl == 0) && (total_memory >= (1ull << 32))) { 783 puts("Detected "); 784 print_size(total_memory, " of memory\n"); 785 printf(" This U-Boot only supports < 4G of DDR\n"); 786 printf(" You could rebuild it with CONFIG_PHYS_64BIT\n"); 787 printf(" "); /* re-align to match init_func_ram print */ 788 total_memory = CONFIG_MAX_MEM_MAPPED; 789 } 790 #endif 791 792 return total_memory; 793 } 794 795 /* 796 * fsl_ddr_sdram(void) -- this is the main function to be 797 * called by initdram() in the board file. 798 * 799 * It returns amount of memory configured in bytes. 800 */ 801 phys_size_t fsl_ddr_sdram(void) 802 { 803 fsl_ddr_info_t info; 804 805 /* Reset info structure. */ 806 memset(&info, 0, sizeof(fsl_ddr_info_t)); 807 info.mem_base = CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY; 808 info.first_ctrl = 0; 809 info.num_ctrls = CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS; 810 info.dimm_slots_per_ctrl = CONFIG_DIMM_SLOTS_PER_CTLR; 811 info.board_need_mem_reset = board_need_mem_reset; 812 info.board_mem_reset = board_assert_mem_reset; 813 info.board_mem_de_reset = board_deassert_mem_reset; 814 remove_unused_controllers(&info); 815 816 return __fsl_ddr_sdram(&info); 817 } 818 819 #ifdef CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS 820 phys_size_t fsl_other_ddr_sdram(unsigned long long base, 821 unsigned int first_ctrl, 822 unsigned int num_ctrls, 823 unsigned int dimm_slots_per_ctrl, 824 int (*board_need_reset)(void), 825 void (*board_reset)(void), 826 void (*board_de_reset)(void)) 827 { 828 fsl_ddr_info_t info; 829 830 /* Reset info structure. */ 831 memset(&info, 0, sizeof(fsl_ddr_info_t)); 832 info.mem_base = base; 833 info.first_ctrl = first_ctrl; 834 info.num_ctrls = num_ctrls; 835 info.dimm_slots_per_ctrl = dimm_slots_per_ctrl; 836 info.board_need_mem_reset = board_need_reset; 837 info.board_mem_reset = board_reset; 838 info.board_mem_de_reset = board_de_reset; 839 840 return __fsl_ddr_sdram(&info); 841 } 842 #endif 843 844 /* 845 * fsl_ddr_sdram_size(first_ctrl, last_intlv) - This function only returns the 846 * size of the total memory without setting ddr control registers. 847 */ 848 phys_size_t 849 fsl_ddr_sdram_size(void) 850 { 851 fsl_ddr_info_t info; 852 unsigned long long total_memory = 0; 853 854 memset(&info, 0 , sizeof(fsl_ddr_info_t)); 855 info.mem_base = CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY; 856 info.first_ctrl = 0; 857 info.num_ctrls = CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS; 858 info.dimm_slots_per_ctrl = CONFIG_DIMM_SLOTS_PER_CTLR; 859 info.board_need_mem_reset = NULL; 860 861 /* Compute it once normally. */ 862 total_memory = fsl_ddr_compute(&info, STEP_GET_SPD, 1); 863 864 return total_memory; 865 } 866