1 /* 2 * Copyright 2008-2014 Freescale Semiconductor, Inc. 3 * 4 * SPDX-License-Identifier: GPL-2.0+ 5 */ 6 7 /* 8 * Generic driver for Freescale DDR/DDR2/DDR3 memory controller. 9 * Based on code from spd_sdram.c 10 * Author: James Yang [at freescale.com] 11 */ 12 13 #include <common.h> 14 #include <fsl_ddr_sdram.h> 15 16 #include <fsl_ddr.h> 17 #include <fsl_immap.h> 18 #include <asm/io.h> 19 20 unsigned int picos_to_mclk(unsigned int picos); 21 22 /* 23 * Determine Rtt value. 24 * 25 * This should likely be either board or controller specific. 26 * 27 * Rtt(nominal) - DDR2: 28 * 0 = Rtt disabled 29 * 1 = 75 ohm 30 * 2 = 150 ohm 31 * 3 = 50 ohm 32 * Rtt(nominal) - DDR3: 33 * 0 = Rtt disabled 34 * 1 = 60 ohm 35 * 2 = 120 ohm 36 * 3 = 40 ohm 37 * 4 = 20 ohm 38 * 5 = 30 ohm 39 * 40 * FIXME: Apparently 8641 needs a value of 2 41 * FIXME: Old code seys if 667 MHz or higher, use 3 on 8572 42 * 43 * FIXME: There was some effort down this line earlier: 44 * 45 * unsigned int i; 46 * for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL/2; i++) { 47 * if (popts->dimmslot[i].num_valid_cs 48 * && (popts->cs_local_opts[2*i].odt_rd_cfg 49 * || popts->cs_local_opts[2*i].odt_wr_cfg)) { 50 * rtt = 2; 51 * break; 52 * } 53 * } 54 */ 55 static inline int fsl_ddr_get_rtt(void) 56 { 57 int rtt; 58 59 #if defined(CONFIG_SYS_FSL_DDR1) 60 rtt = 0; 61 #elif defined(CONFIG_SYS_FSL_DDR2) 62 rtt = 3; 63 #else 64 rtt = 0; 65 #endif 66 67 return rtt; 68 } 69 70 #ifdef CONFIG_SYS_FSL_DDR4 71 /* 72 * compute CAS write latency according to DDR4 spec 73 * CWL = 9 for <= 1600MT/s 74 * 10 for <= 1866MT/s 75 * 11 for <= 2133MT/s 76 * 12 for <= 2400MT/s 77 * 14 for <= 2667MT/s 78 * 16 for <= 2933MT/s 79 * 18 for higher 80 */ 81 static inline unsigned int compute_cas_write_latency(void) 82 { 83 unsigned int cwl; 84 const unsigned int mclk_ps = get_memory_clk_period_ps(); 85 if (mclk_ps >= 1250) 86 cwl = 9; 87 else if (mclk_ps >= 1070) 88 cwl = 10; 89 else if (mclk_ps >= 935) 90 cwl = 11; 91 else if (mclk_ps >= 833) 92 cwl = 12; 93 else if (mclk_ps >= 750) 94 cwl = 14; 95 else if (mclk_ps >= 681) 96 cwl = 16; 97 else 98 cwl = 18; 99 100 return cwl; 101 } 102 #else 103 /* 104 * compute the CAS write latency according to DDR3 spec 105 * CWL = 5 if tCK >= 2.5ns 106 * 6 if 2.5ns > tCK >= 1.875ns 107 * 7 if 1.875ns > tCK >= 1.5ns 108 * 8 if 1.5ns > tCK >= 1.25ns 109 * 9 if 1.25ns > tCK >= 1.07ns 110 * 10 if 1.07ns > tCK >= 0.935ns 111 * 11 if 0.935ns > tCK >= 0.833ns 112 * 12 if 0.833ns > tCK >= 0.75ns 113 */ 114 static inline unsigned int compute_cas_write_latency(void) 115 { 116 unsigned int cwl; 117 const unsigned int mclk_ps = get_memory_clk_period_ps(); 118 119 if (mclk_ps >= 2500) 120 cwl = 5; 121 else if (mclk_ps >= 1875) 122 cwl = 6; 123 else if (mclk_ps >= 1500) 124 cwl = 7; 125 else if (mclk_ps >= 1250) 126 cwl = 8; 127 else if (mclk_ps >= 1070) 128 cwl = 9; 129 else if (mclk_ps >= 935) 130 cwl = 10; 131 else if (mclk_ps >= 833) 132 cwl = 11; 133 else if (mclk_ps >= 750) 134 cwl = 12; 135 else { 136 cwl = 12; 137 printf("Warning: CWL is out of range\n"); 138 } 139 return cwl; 140 } 141 #endif 142 143 /* Chip Select Configuration (CSn_CONFIG) */ 144 static void set_csn_config(int dimm_number, int i, fsl_ddr_cfg_regs_t *ddr, 145 const memctl_options_t *popts, 146 const dimm_params_t *dimm_params) 147 { 148 unsigned int cs_n_en = 0; /* Chip Select enable */ 149 unsigned int intlv_en = 0; /* Memory controller interleave enable */ 150 unsigned int intlv_ctl = 0; /* Interleaving control */ 151 unsigned int ap_n_en = 0; /* Chip select n auto-precharge enable */ 152 unsigned int odt_rd_cfg = 0; /* ODT for reads configuration */ 153 unsigned int odt_wr_cfg = 0; /* ODT for writes configuration */ 154 unsigned int ba_bits_cs_n = 0; /* Num of bank bits for SDRAM on CSn */ 155 unsigned int row_bits_cs_n = 0; /* Num of row bits for SDRAM on CSn */ 156 unsigned int col_bits_cs_n = 0; /* Num of ocl bits for SDRAM on CSn */ 157 int go_config = 0; 158 #ifdef CONFIG_SYS_FSL_DDR4 159 unsigned int bg_bits_cs_n = 0; /* Num of bank group bits */ 160 #else 161 unsigned int n_banks_per_sdram_device; 162 #endif 163 164 /* Compute CS_CONFIG only for existing ranks of each DIMM. */ 165 switch (i) { 166 case 0: 167 if (dimm_params[dimm_number].n_ranks > 0) { 168 go_config = 1; 169 /* These fields only available in CS0_CONFIG */ 170 if (!popts->memctl_interleaving) 171 break; 172 switch (popts->memctl_interleaving_mode) { 173 case FSL_DDR_256B_INTERLEAVING: 174 case FSL_DDR_CACHE_LINE_INTERLEAVING: 175 case FSL_DDR_PAGE_INTERLEAVING: 176 case FSL_DDR_BANK_INTERLEAVING: 177 case FSL_DDR_SUPERBANK_INTERLEAVING: 178 intlv_en = popts->memctl_interleaving; 179 intlv_ctl = popts->memctl_interleaving_mode; 180 break; 181 default: 182 break; 183 } 184 } 185 break; 186 case 1: 187 if ((dimm_number == 0 && dimm_params[0].n_ranks > 1) || \ 188 (dimm_number == 1 && dimm_params[1].n_ranks > 0)) 189 go_config = 1; 190 break; 191 case 2: 192 if ((dimm_number == 0 && dimm_params[0].n_ranks > 2) || \ 193 (dimm_number >= 1 && dimm_params[dimm_number].n_ranks > 0)) 194 go_config = 1; 195 break; 196 case 3: 197 if ((dimm_number == 0 && dimm_params[0].n_ranks > 3) || \ 198 (dimm_number == 1 && dimm_params[1].n_ranks > 1) || \ 199 (dimm_number == 3 && dimm_params[3].n_ranks > 0)) 200 go_config = 1; 201 break; 202 default: 203 break; 204 } 205 if (go_config) { 206 cs_n_en = 1; 207 ap_n_en = popts->cs_local_opts[i].auto_precharge; 208 odt_rd_cfg = popts->cs_local_opts[i].odt_rd_cfg; 209 odt_wr_cfg = popts->cs_local_opts[i].odt_wr_cfg; 210 #ifdef CONFIG_SYS_FSL_DDR4 211 ba_bits_cs_n = dimm_params[dimm_number].bank_addr_bits; 212 bg_bits_cs_n = dimm_params[dimm_number].bank_group_bits; 213 #else 214 n_banks_per_sdram_device 215 = dimm_params[dimm_number].n_banks_per_sdram_device; 216 ba_bits_cs_n = __ilog2(n_banks_per_sdram_device) - 2; 217 #endif 218 row_bits_cs_n = dimm_params[dimm_number].n_row_addr - 12; 219 col_bits_cs_n = dimm_params[dimm_number].n_col_addr - 8; 220 } 221 ddr->cs[i].config = (0 222 | ((cs_n_en & 0x1) << 31) 223 | ((intlv_en & 0x3) << 29) 224 | ((intlv_ctl & 0xf) << 24) 225 | ((ap_n_en & 0x1) << 23) 226 227 /* XXX: some implementation only have 1 bit starting at left */ 228 | ((odt_rd_cfg & 0x7) << 20) 229 230 /* XXX: Some implementation only have 1 bit starting at left */ 231 | ((odt_wr_cfg & 0x7) << 16) 232 233 | ((ba_bits_cs_n & 0x3) << 14) 234 | ((row_bits_cs_n & 0x7) << 8) 235 #ifdef CONFIG_SYS_FSL_DDR4 236 | ((bg_bits_cs_n & 0x3) << 4) 237 #endif 238 | ((col_bits_cs_n & 0x7) << 0) 239 ); 240 debug("FSLDDR: cs[%d]_config = 0x%08x\n", i,ddr->cs[i].config); 241 } 242 243 /* Chip Select Configuration 2 (CSn_CONFIG_2) */ 244 /* FIXME: 8572 */ 245 static void set_csn_config_2(int i, fsl_ddr_cfg_regs_t *ddr) 246 { 247 unsigned int pasr_cfg = 0; /* Partial array self refresh config */ 248 249 ddr->cs[i].config_2 = ((pasr_cfg & 7) << 24); 250 debug("FSLDDR: cs[%d]_config_2 = 0x%08x\n", i, ddr->cs[i].config_2); 251 } 252 253 /* -3E = 667 CL5, -25 = CL6 800, -25E = CL5 800 */ 254 255 #if !defined(CONFIG_SYS_FSL_DDR1) 256 static inline int avoid_odt_overlap(const dimm_params_t *dimm_params) 257 { 258 #if CONFIG_DIMM_SLOTS_PER_CTLR == 1 259 if (dimm_params[0].n_ranks == 4) 260 return 1; 261 #endif 262 263 #if CONFIG_DIMM_SLOTS_PER_CTLR == 2 264 if ((dimm_params[0].n_ranks == 2) && 265 (dimm_params[1].n_ranks == 2)) 266 return 1; 267 268 #ifdef CONFIG_FSL_DDR_FIRST_SLOT_QUAD_CAPABLE 269 if (dimm_params[0].n_ranks == 4) 270 return 1; 271 #endif 272 #endif 273 return 0; 274 } 275 276 /* 277 * DDR SDRAM Timing Configuration 0 (TIMING_CFG_0) 278 * 279 * Avoid writing for DDR I. The new PQ38 DDR controller 280 * dreams up non-zero default values to be backwards compatible. 281 */ 282 static void set_timing_cfg_0(fsl_ddr_cfg_regs_t *ddr, 283 const memctl_options_t *popts, 284 const dimm_params_t *dimm_params) 285 { 286 unsigned char trwt_mclk = 0; /* Read-to-write turnaround */ 287 unsigned char twrt_mclk = 0; /* Write-to-read turnaround */ 288 /* 7.5 ns on -3E; 0 means WL - CL + BL/2 + 1 */ 289 unsigned char trrt_mclk = 0; /* Read-to-read turnaround */ 290 unsigned char twwt_mclk = 0; /* Write-to-write turnaround */ 291 292 /* Active powerdown exit timing (tXARD and tXARDS). */ 293 unsigned char act_pd_exit_mclk; 294 /* Precharge powerdown exit timing (tXP). */ 295 unsigned char pre_pd_exit_mclk; 296 /* ODT powerdown exit timing (tAXPD). */ 297 unsigned char taxpd_mclk = 0; 298 /* Mode register set cycle time (tMRD). */ 299 unsigned char tmrd_mclk; 300 301 #ifdef CONFIG_SYS_FSL_DDR4 302 /* tXP=max(4nCK, 6ns) */ 303 int txp = max((get_memory_clk_period_ps() * 4), 6000); /* unit=ps */ 304 trwt_mclk = 2; 305 twrt_mclk = 1; 306 act_pd_exit_mclk = picos_to_mclk(txp); 307 pre_pd_exit_mclk = act_pd_exit_mclk; 308 /* 309 * MRS_CYC = max(tMRD, tMOD) 310 * tMRD = 8nCK, tMOD = max(24nCK, 15ns) 311 */ 312 tmrd_mclk = max(24, picos_to_mclk(15000)); 313 #elif defined(CONFIG_SYS_FSL_DDR3) 314 /* 315 * (tXARD and tXARDS). Empirical? 316 * The DDR3 spec has not tXARD, 317 * we use the tXP instead of it. 318 * tXP=max(3nCK, 7.5ns) for DDR3. 319 * spec has not the tAXPD, we use 320 * tAXPD=1, need design to confirm. 321 */ 322 int txp = max((get_memory_clk_period_ps() * 3), 7500); /* unit=ps */ 323 unsigned int data_rate = get_ddr_freq(0); 324 tmrd_mclk = 4; 325 /* set the turnaround time */ 326 327 /* 328 * for single quad-rank DIMM and two dual-rank DIMMs 329 * to avoid ODT overlap 330 */ 331 if (avoid_odt_overlap(dimm_params)) { 332 twwt_mclk = 2; 333 trrt_mclk = 1; 334 } 335 /* for faster clock, need more time for data setup */ 336 trwt_mclk = (data_rate/1000000 > 1800) ? 2 : 1; 337 338 if ((data_rate/1000000 > 1150) || (popts->memctl_interleaving)) 339 twrt_mclk = 1; 340 341 if (popts->dynamic_power == 0) { /* powerdown is not used */ 342 act_pd_exit_mclk = 1; 343 pre_pd_exit_mclk = 1; 344 taxpd_mclk = 1; 345 } else { 346 /* act_pd_exit_mclk = tXARD, see above */ 347 act_pd_exit_mclk = picos_to_mclk(txp); 348 /* Mode register MR0[A12] is '1' - fast exit */ 349 pre_pd_exit_mclk = act_pd_exit_mclk; 350 taxpd_mclk = 1; 351 } 352 #else /* CONFIG_SYS_FSL_DDR2 */ 353 /* 354 * (tXARD and tXARDS). Empirical? 355 * tXARD = 2 for DDR2 356 * tXP=2 357 * tAXPD=8 358 */ 359 act_pd_exit_mclk = 2; 360 pre_pd_exit_mclk = 2; 361 taxpd_mclk = 8; 362 tmrd_mclk = 2; 363 #endif 364 365 if (popts->trwt_override) 366 trwt_mclk = popts->trwt; 367 368 ddr->timing_cfg_0 = (0 369 | ((trwt_mclk & 0x3) << 30) /* RWT */ 370 | ((twrt_mclk & 0x3) << 28) /* WRT */ 371 | ((trrt_mclk & 0x3) << 26) /* RRT */ 372 | ((twwt_mclk & 0x3) << 24) /* WWT */ 373 | ((act_pd_exit_mclk & 0xf) << 20) /* ACT_PD_EXIT */ 374 | ((pre_pd_exit_mclk & 0xF) << 16) /* PRE_PD_EXIT */ 375 | ((taxpd_mclk & 0xf) << 8) /* ODT_PD_EXIT */ 376 | ((tmrd_mclk & 0x1f) << 0) /* MRS_CYC */ 377 ); 378 debug("FSLDDR: timing_cfg_0 = 0x%08x\n", ddr->timing_cfg_0); 379 } 380 #endif /* defined(CONFIG_SYS_FSL_DDR2) */ 381 382 /* DDR SDRAM Timing Configuration 3 (TIMING_CFG_3) */ 383 static void set_timing_cfg_3(fsl_ddr_cfg_regs_t *ddr, 384 const memctl_options_t *popts, 385 const common_timing_params_t *common_dimm, 386 unsigned int cas_latency, 387 unsigned int additive_latency) 388 { 389 /* Extended precharge to activate interval (tRP) */ 390 unsigned int ext_pretoact = 0; 391 /* Extended Activate to precharge interval (tRAS) */ 392 unsigned int ext_acttopre = 0; 393 /* Extended activate to read/write interval (tRCD) */ 394 unsigned int ext_acttorw = 0; 395 /* Extended refresh recovery time (tRFC) */ 396 unsigned int ext_refrec; 397 /* Extended MCAS latency from READ cmd */ 398 unsigned int ext_caslat = 0; 399 /* Extended additive latency */ 400 unsigned int ext_add_lat = 0; 401 /* Extended last data to precharge interval (tWR) */ 402 unsigned int ext_wrrec = 0; 403 /* Control Adjust */ 404 unsigned int cntl_adj = 0; 405 406 ext_pretoact = picos_to_mclk(common_dimm->trp_ps) >> 4; 407 ext_acttopre = picos_to_mclk(common_dimm->tras_ps) >> 4; 408 ext_acttorw = picos_to_mclk(common_dimm->trcd_ps) >> 4; 409 ext_caslat = (2 * cas_latency - 1) >> 4; 410 ext_add_lat = additive_latency >> 4; 411 #ifdef CONFIG_SYS_FSL_DDR4 412 ext_refrec = (picos_to_mclk(common_dimm->trfc1_ps) - 8) >> 4; 413 #else 414 ext_refrec = (picos_to_mclk(common_dimm->trfc_ps) - 8) >> 4; 415 /* ext_wrrec only deals with 16 clock and above, or 14 with OTF */ 416 #endif 417 ext_wrrec = (picos_to_mclk(common_dimm->twr_ps) + 418 (popts->otf_burst_chop_en ? 2 : 0)) >> 4; 419 420 ddr->timing_cfg_3 = (0 421 | ((ext_pretoact & 0x1) << 28) 422 | ((ext_acttopre & 0x3) << 24) 423 | ((ext_acttorw & 0x1) << 22) 424 | ((ext_refrec & 0x1F) << 16) 425 | ((ext_caslat & 0x3) << 12) 426 | ((ext_add_lat & 0x1) << 10) 427 | ((ext_wrrec & 0x1) << 8) 428 | ((cntl_adj & 0x7) << 0) 429 ); 430 debug("FSLDDR: timing_cfg_3 = 0x%08x\n", ddr->timing_cfg_3); 431 } 432 433 /* DDR SDRAM Timing Configuration 1 (TIMING_CFG_1) */ 434 static void set_timing_cfg_1(fsl_ddr_cfg_regs_t *ddr, 435 const memctl_options_t *popts, 436 const common_timing_params_t *common_dimm, 437 unsigned int cas_latency) 438 { 439 /* Precharge-to-activate interval (tRP) */ 440 unsigned char pretoact_mclk; 441 /* Activate to precharge interval (tRAS) */ 442 unsigned char acttopre_mclk; 443 /* Activate to read/write interval (tRCD) */ 444 unsigned char acttorw_mclk; 445 /* CASLAT */ 446 unsigned char caslat_ctrl; 447 /* Refresh recovery time (tRFC) ; trfc_low */ 448 unsigned char refrec_ctrl; 449 /* Last data to precharge minimum interval (tWR) */ 450 unsigned char wrrec_mclk; 451 /* Activate-to-activate interval (tRRD) */ 452 unsigned char acttoact_mclk; 453 /* Last write data pair to read command issue interval (tWTR) */ 454 unsigned char wrtord_mclk; 455 #ifdef CONFIG_SYS_FSL_DDR4 456 /* DDR4 supports 10, 12, 14, 16, 18, 20, 24 */ 457 static const u8 wrrec_table[] = { 458 10, 10, 10, 10, 10, 459 10, 10, 10, 10, 10, 460 12, 12, 14, 14, 16, 461 16, 18, 18, 20, 20, 462 24, 24, 24, 24}; 463 #else 464 /* DDR_SDRAM_MODE doesn't support 9,11,13,15 */ 465 static const u8 wrrec_table[] = { 466 1, 2, 3, 4, 5, 6, 7, 8, 10, 10, 12, 12, 14, 14, 0, 0}; 467 #endif 468 469 pretoact_mclk = picos_to_mclk(common_dimm->trp_ps); 470 acttopre_mclk = picos_to_mclk(common_dimm->tras_ps); 471 acttorw_mclk = picos_to_mclk(common_dimm->trcd_ps); 472 473 /* 474 * Translate CAS Latency to a DDR controller field value: 475 * 476 * CAS Lat DDR I DDR II Ctrl 477 * Clocks SPD Bit SPD Bit Value 478 * ------- ------- ------- ----- 479 * 1.0 0 0001 480 * 1.5 1 0010 481 * 2.0 2 2 0011 482 * 2.5 3 0100 483 * 3.0 4 3 0101 484 * 3.5 5 0110 485 * 4.0 4 0111 486 * 4.5 1000 487 * 5.0 5 1001 488 */ 489 #if defined(CONFIG_SYS_FSL_DDR1) 490 caslat_ctrl = (cas_latency + 1) & 0x07; 491 #elif defined(CONFIG_SYS_FSL_DDR2) 492 caslat_ctrl = 2 * cas_latency - 1; 493 #else 494 /* 495 * if the CAS latency more than 8 cycle, 496 * we need set extend bit for it at 497 * TIMING_CFG_3[EXT_CASLAT] 498 */ 499 if (fsl_ddr_get_version() <= 0x40400) 500 caslat_ctrl = 2 * cas_latency - 1; 501 else 502 caslat_ctrl = (cas_latency - 1) << 1; 503 #endif 504 505 #ifdef CONFIG_SYS_FSL_DDR4 506 refrec_ctrl = picos_to_mclk(common_dimm->trfc1_ps) - 8; 507 wrrec_mclk = picos_to_mclk(common_dimm->twr_ps); 508 acttoact_mclk = max(picos_to_mclk(common_dimm->trrds_ps), 4); 509 wrtord_mclk = max(2, picos_to_mclk(2500)); 510 if ((wrrec_mclk < 1) || (wrrec_mclk > 24)) 511 printf("Error: WRREC doesn't support %d clocks\n", wrrec_mclk); 512 else 513 wrrec_mclk = wrrec_table[wrrec_mclk - 1]; 514 #else 515 refrec_ctrl = picos_to_mclk(common_dimm->trfc_ps) - 8; 516 wrrec_mclk = picos_to_mclk(common_dimm->twr_ps); 517 acttoact_mclk = picos_to_mclk(common_dimm->trrd_ps); 518 wrtord_mclk = picos_to_mclk(common_dimm->twtr_ps); 519 if ((wrrec_mclk < 1) || (wrrec_mclk > 16)) 520 printf("Error: WRREC doesn't support %d clocks\n", wrrec_mclk); 521 else 522 wrrec_mclk = wrrec_table[wrrec_mclk - 1]; 523 #endif 524 if (popts->otf_burst_chop_en) 525 wrrec_mclk += 2; 526 527 /* 528 * JEDEC has min requirement for tRRD 529 */ 530 #if defined(CONFIG_SYS_FSL_DDR3) 531 if (acttoact_mclk < 4) 532 acttoact_mclk = 4; 533 #endif 534 /* 535 * JEDEC has some min requirements for tWTR 536 */ 537 #if defined(CONFIG_SYS_FSL_DDR2) 538 if (wrtord_mclk < 2) 539 wrtord_mclk = 2; 540 #elif defined(CONFIG_SYS_FSL_DDR3) 541 if (wrtord_mclk < 4) 542 wrtord_mclk = 4; 543 #endif 544 if (popts->otf_burst_chop_en) 545 wrtord_mclk += 2; 546 547 ddr->timing_cfg_1 = (0 548 | ((pretoact_mclk & 0x0F) << 28) 549 | ((acttopre_mclk & 0x0F) << 24) 550 | ((acttorw_mclk & 0xF) << 20) 551 | ((caslat_ctrl & 0xF) << 16) 552 | ((refrec_ctrl & 0xF) << 12) 553 | ((wrrec_mclk & 0x0F) << 8) 554 | ((acttoact_mclk & 0x0F) << 4) 555 | ((wrtord_mclk & 0x0F) << 0) 556 ); 557 debug("FSLDDR: timing_cfg_1 = 0x%08x\n", ddr->timing_cfg_1); 558 } 559 560 /* DDR SDRAM Timing Configuration 2 (TIMING_CFG_2) */ 561 static void set_timing_cfg_2(fsl_ddr_cfg_regs_t *ddr, 562 const memctl_options_t *popts, 563 const common_timing_params_t *common_dimm, 564 unsigned int cas_latency, 565 unsigned int additive_latency) 566 { 567 /* Additive latency */ 568 unsigned char add_lat_mclk; 569 /* CAS-to-preamble override */ 570 unsigned short cpo; 571 /* Write latency */ 572 unsigned char wr_lat; 573 /* Read to precharge (tRTP) */ 574 unsigned char rd_to_pre; 575 /* Write command to write data strobe timing adjustment */ 576 unsigned char wr_data_delay; 577 /* Minimum CKE pulse width (tCKE) */ 578 unsigned char cke_pls; 579 /* Window for four activates (tFAW) */ 580 unsigned short four_act; 581 582 /* FIXME add check that this must be less than acttorw_mclk */ 583 add_lat_mclk = additive_latency; 584 cpo = popts->cpo_override; 585 586 #if defined(CONFIG_SYS_FSL_DDR1) 587 /* 588 * This is a lie. It should really be 1, but if it is 589 * set to 1, bits overlap into the old controller's 590 * otherwise unused ACSM field. If we leave it 0, then 591 * the HW will magically treat it as 1 for DDR 1. Oh Yea. 592 */ 593 wr_lat = 0; 594 #elif defined(CONFIG_SYS_FSL_DDR2) 595 wr_lat = cas_latency - 1; 596 #else 597 wr_lat = compute_cas_write_latency(); 598 #endif 599 600 #ifdef CONFIG_SYS_FSL_DDR4 601 rd_to_pre = picos_to_mclk(7500); 602 #else 603 rd_to_pre = picos_to_mclk(common_dimm->trtp_ps); 604 #endif 605 /* 606 * JEDEC has some min requirements for tRTP 607 */ 608 #if defined(CONFIG_SYS_FSL_DDR2) 609 if (rd_to_pre < 2) 610 rd_to_pre = 2; 611 #elif defined(CONFIG_SYS_FSL_DDR3) || defined(CONFIG_SYS_FSL_DDR4) 612 if (rd_to_pre < 4) 613 rd_to_pre = 4; 614 #endif 615 if (popts->otf_burst_chop_en) 616 rd_to_pre += 2; /* according to UM */ 617 618 wr_data_delay = popts->write_data_delay; 619 #ifdef CONFIG_SYS_FSL_DDR4 620 cpo = 0; 621 cke_pls = max(3, picos_to_mclk(5000)); 622 #else 623 cke_pls = picos_to_mclk(popts->tcke_clock_pulse_width_ps); 624 #endif 625 626 four_act = picos_to_mclk(popts->tfaw_window_four_activates_ps); 627 628 ddr->timing_cfg_2 = (0 629 | ((add_lat_mclk & 0xf) << 28) 630 | ((cpo & 0x1f) << 23) 631 | ((wr_lat & 0xf) << 19) 632 | ((wr_lat & 0x10) << 14) 633 | ((rd_to_pre & RD_TO_PRE_MASK) << RD_TO_PRE_SHIFT) 634 | ((wr_data_delay & WR_DATA_DELAY_MASK) << WR_DATA_DELAY_SHIFT) 635 | ((cke_pls & 0x7) << 6) 636 | ((four_act & 0x3f) << 0) 637 ); 638 debug("FSLDDR: timing_cfg_2 = 0x%08x\n", ddr->timing_cfg_2); 639 } 640 641 /* DDR SDRAM Register Control Word */ 642 static void set_ddr_sdram_rcw(fsl_ddr_cfg_regs_t *ddr, 643 const memctl_options_t *popts, 644 const common_timing_params_t *common_dimm) 645 { 646 if (common_dimm->all_dimms_registered && 647 !common_dimm->all_dimms_unbuffered) { 648 if (popts->rcw_override) { 649 ddr->ddr_sdram_rcw_1 = popts->rcw_1; 650 ddr->ddr_sdram_rcw_2 = popts->rcw_2; 651 } else { 652 ddr->ddr_sdram_rcw_1 = 653 common_dimm->rcw[0] << 28 | \ 654 common_dimm->rcw[1] << 24 | \ 655 common_dimm->rcw[2] << 20 | \ 656 common_dimm->rcw[3] << 16 | \ 657 common_dimm->rcw[4] << 12 | \ 658 common_dimm->rcw[5] << 8 | \ 659 common_dimm->rcw[6] << 4 | \ 660 common_dimm->rcw[7]; 661 ddr->ddr_sdram_rcw_2 = 662 common_dimm->rcw[8] << 28 | \ 663 common_dimm->rcw[9] << 24 | \ 664 common_dimm->rcw[10] << 20 | \ 665 common_dimm->rcw[11] << 16 | \ 666 common_dimm->rcw[12] << 12 | \ 667 common_dimm->rcw[13] << 8 | \ 668 common_dimm->rcw[14] << 4 | \ 669 common_dimm->rcw[15]; 670 } 671 debug("FSLDDR: ddr_sdram_rcw_1 = 0x%08x\n", ddr->ddr_sdram_rcw_1); 672 debug("FSLDDR: ddr_sdram_rcw_2 = 0x%08x\n", ddr->ddr_sdram_rcw_2); 673 } 674 } 675 676 /* DDR SDRAM control configuration (DDR_SDRAM_CFG) */ 677 static void set_ddr_sdram_cfg(fsl_ddr_cfg_regs_t *ddr, 678 const memctl_options_t *popts, 679 const common_timing_params_t *common_dimm) 680 { 681 unsigned int mem_en; /* DDR SDRAM interface logic enable */ 682 unsigned int sren; /* Self refresh enable (during sleep) */ 683 unsigned int ecc_en; /* ECC enable. */ 684 unsigned int rd_en; /* Registered DIMM enable */ 685 unsigned int sdram_type; /* Type of SDRAM */ 686 unsigned int dyn_pwr; /* Dynamic power management mode */ 687 unsigned int dbw; /* DRAM dta bus width */ 688 unsigned int eight_be = 0; /* 8-beat burst enable, DDR2 is zero */ 689 unsigned int ncap = 0; /* Non-concurrent auto-precharge */ 690 unsigned int threet_en; /* Enable 3T timing */ 691 unsigned int twot_en; /* Enable 2T timing */ 692 unsigned int ba_intlv_ctl; /* Bank (CS) interleaving control */ 693 unsigned int x32_en = 0; /* x32 enable */ 694 unsigned int pchb8 = 0; /* precharge bit 8 enable */ 695 unsigned int hse; /* Global half strength override */ 696 unsigned int mem_halt = 0; /* memory controller halt */ 697 unsigned int bi = 0; /* Bypass initialization */ 698 699 mem_en = 1; 700 sren = popts->self_refresh_in_sleep; 701 if (common_dimm->all_dimms_ecc_capable) { 702 /* Allow setting of ECC only if all DIMMs are ECC. */ 703 ecc_en = popts->ecc_mode; 704 } else { 705 ecc_en = 0; 706 } 707 708 if (common_dimm->all_dimms_registered && 709 !common_dimm->all_dimms_unbuffered) { 710 rd_en = 1; 711 twot_en = 0; 712 } else { 713 rd_en = 0; 714 twot_en = popts->twot_en; 715 } 716 717 sdram_type = CONFIG_FSL_SDRAM_TYPE; 718 719 dyn_pwr = popts->dynamic_power; 720 dbw = popts->data_bus_width; 721 /* 8-beat burst enable DDR-III case 722 * we must clear it when use the on-the-fly mode, 723 * must set it when use the 32-bits bus mode. 724 */ 725 if ((sdram_type == SDRAM_TYPE_DDR3) || 726 (sdram_type == SDRAM_TYPE_DDR4)) { 727 if (popts->burst_length == DDR_BL8) 728 eight_be = 1; 729 if (popts->burst_length == DDR_OTF) 730 eight_be = 0; 731 if (dbw == 0x1) 732 eight_be = 1; 733 } 734 735 threet_en = popts->threet_en; 736 ba_intlv_ctl = popts->ba_intlv_ctl; 737 hse = popts->half_strength_driver_enable; 738 739 ddr->ddr_sdram_cfg = (0 740 | ((mem_en & 0x1) << 31) 741 | ((sren & 0x1) << 30) 742 | ((ecc_en & 0x1) << 29) 743 | ((rd_en & 0x1) << 28) 744 | ((sdram_type & 0x7) << 24) 745 | ((dyn_pwr & 0x1) << 21) 746 | ((dbw & 0x3) << 19) 747 | ((eight_be & 0x1) << 18) 748 | ((ncap & 0x1) << 17) 749 | ((threet_en & 0x1) << 16) 750 | ((twot_en & 0x1) << 15) 751 | ((ba_intlv_ctl & 0x7F) << 8) 752 | ((x32_en & 0x1) << 5) 753 | ((pchb8 & 0x1) << 4) 754 | ((hse & 0x1) << 3) 755 | ((mem_halt & 0x1) << 1) 756 | ((bi & 0x1) << 0) 757 ); 758 debug("FSLDDR: ddr_sdram_cfg = 0x%08x\n", ddr->ddr_sdram_cfg); 759 } 760 761 /* DDR SDRAM control configuration 2 (DDR_SDRAM_CFG_2) */ 762 static void set_ddr_sdram_cfg_2(fsl_ddr_cfg_regs_t *ddr, 763 const memctl_options_t *popts, 764 const unsigned int unq_mrs_en) 765 { 766 unsigned int frc_sr = 0; /* Force self refresh */ 767 unsigned int sr_ie = 0; /* Self-refresh interrupt enable */ 768 unsigned int odt_cfg = 0; /* ODT configuration */ 769 unsigned int num_pr; /* Number of posted refreshes */ 770 unsigned int slow = 0; /* DDR will be run less than 1250 */ 771 unsigned int x4_en = 0; /* x4 DRAM enable */ 772 unsigned int obc_cfg; /* On-The-Fly Burst Chop Cfg */ 773 unsigned int ap_en; /* Address Parity Enable */ 774 unsigned int d_init; /* DRAM data initialization */ 775 unsigned int rcw_en = 0; /* Register Control Word Enable */ 776 unsigned int md_en = 0; /* Mirrored DIMM Enable */ 777 unsigned int qd_en = 0; /* quad-rank DIMM Enable */ 778 int i; 779 #ifndef CONFIG_SYS_FSL_DDR4 780 unsigned int dll_rst_dis = 1; /* DLL reset disable */ 781 unsigned int dqs_cfg; /* DQS configuration */ 782 783 dqs_cfg = popts->dqs_config; 784 #endif 785 for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) { 786 if (popts->cs_local_opts[i].odt_rd_cfg 787 || popts->cs_local_opts[i].odt_wr_cfg) { 788 odt_cfg = SDRAM_CFG2_ODT_ONLY_READ; 789 break; 790 } 791 } 792 793 num_pr = 1; /* Make this configurable */ 794 795 /* 796 * 8572 manual says 797 * {TIMING_CFG_1[PRETOACT] 798 * + [DDR_SDRAM_CFG_2[NUM_PR] 799 * * ({EXT_REFREC || REFREC} + 8 + 2)]} 800 * << DDR_SDRAM_INTERVAL[REFINT] 801 */ 802 #if defined(CONFIG_SYS_FSL_DDR3) || defined(CONFIG_SYS_FSL_DDR4) 803 obc_cfg = popts->otf_burst_chop_en; 804 #else 805 obc_cfg = 0; 806 #endif 807 808 #if (CONFIG_SYS_FSL_DDR_VER >= FSL_DDR_VER_4_7) 809 slow = get_ddr_freq(0) < 1249000000; 810 #endif 811 812 if (popts->registered_dimm_en) { 813 rcw_en = 1; 814 ap_en = popts->ap_en; 815 } else { 816 ap_en = 0; 817 } 818 819 x4_en = popts->x4_en ? 1 : 0; 820 821 #if defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER) 822 /* Use the DDR controller to auto initialize memory. */ 823 d_init = popts->ecc_init_using_memctl; 824 ddr->ddr_data_init = CONFIG_MEM_INIT_VALUE; 825 debug("DDR: ddr_data_init = 0x%08x\n", ddr->ddr_data_init); 826 #else 827 /* Memory will be initialized via DMA, or not at all. */ 828 d_init = 0; 829 #endif 830 831 #if defined(CONFIG_SYS_FSL_DDR3) || defined(CONFIG_SYS_FSL_DDR4) 832 md_en = popts->mirrored_dimm; 833 #endif 834 qd_en = popts->quad_rank_present ? 1 : 0; 835 ddr->ddr_sdram_cfg_2 = (0 836 | ((frc_sr & 0x1) << 31) 837 | ((sr_ie & 0x1) << 30) 838 #ifndef CONFIG_SYS_FSL_DDR4 839 | ((dll_rst_dis & 0x1) << 29) 840 | ((dqs_cfg & 0x3) << 26) 841 #endif 842 | ((odt_cfg & 0x3) << 21) 843 | ((num_pr & 0xf) << 12) 844 | ((slow & 1) << 11) 845 | (x4_en << 10) 846 | (qd_en << 9) 847 | (unq_mrs_en << 8) 848 | ((obc_cfg & 0x1) << 6) 849 | ((ap_en & 0x1) << 5) 850 | ((d_init & 0x1) << 4) 851 | ((rcw_en & 0x1) << 2) 852 | ((md_en & 0x1) << 0) 853 ); 854 debug("FSLDDR: ddr_sdram_cfg_2 = 0x%08x\n", ddr->ddr_sdram_cfg_2); 855 } 856 857 #ifdef CONFIG_SYS_FSL_DDR4 858 /* DDR SDRAM Mode configuration 2 (DDR_SDRAM_MODE_2) */ 859 static void set_ddr_sdram_mode_2(fsl_ddr_cfg_regs_t *ddr, 860 const memctl_options_t *popts, 861 const common_timing_params_t *common_dimm, 862 const unsigned int unq_mrs_en) 863 { 864 unsigned short esdmode2 = 0; /* Extended SDRAM mode 2 */ 865 unsigned short esdmode3 = 0; /* Extended SDRAM mode 3 */ 866 int i; 867 unsigned int wr_crc = 0; /* Disable */ 868 unsigned int rtt_wr = 0; /* Rtt_WR - dynamic ODT off */ 869 unsigned int srt = 0; /* self-refresh temerature, normal range */ 870 unsigned int cwl = compute_cas_write_latency() - 9; 871 unsigned int mpr = 0; /* serial */ 872 unsigned int wc_lat; 873 const unsigned int mclk_ps = get_memory_clk_period_ps(); 874 875 if (popts->rtt_override) 876 rtt_wr = popts->rtt_wr_override_value; 877 else 878 rtt_wr = popts->cs_local_opts[0].odt_rtt_wr; 879 880 if (common_dimm->extended_op_srt) 881 srt = common_dimm->extended_op_srt; 882 883 esdmode2 = (0 884 | ((wr_crc & 0x1) << 12) 885 | ((rtt_wr & 0x3) << 9) 886 | ((srt & 0x3) << 6) 887 | ((cwl & 0x7) << 3)); 888 889 if (mclk_ps >= 1250) 890 wc_lat = 0; 891 else if (mclk_ps >= 833) 892 wc_lat = 1; 893 else 894 wc_lat = 2; 895 896 esdmode3 = (0 897 | ((mpr & 0x3) << 11) 898 | ((wc_lat & 0x3) << 9)); 899 900 ddr->ddr_sdram_mode_2 = (0 901 | ((esdmode2 & 0xFFFF) << 16) 902 | ((esdmode3 & 0xFFFF) << 0) 903 ); 904 debug("FSLDDR: ddr_sdram_mode_2 = 0x%08x\n", ddr->ddr_sdram_mode_2); 905 906 if (unq_mrs_en) { /* unique mode registers are supported */ 907 for (i = 1; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) { 908 if (popts->rtt_override) 909 rtt_wr = popts->rtt_wr_override_value; 910 else 911 rtt_wr = popts->cs_local_opts[i].odt_rtt_wr; 912 913 esdmode2 &= 0xF9FF; /* clear bit 10, 9 */ 914 esdmode2 |= (rtt_wr & 0x3) << 9; 915 switch (i) { 916 case 1: 917 ddr->ddr_sdram_mode_4 = (0 918 | ((esdmode2 & 0xFFFF) << 16) 919 | ((esdmode3 & 0xFFFF) << 0) 920 ); 921 break; 922 case 2: 923 ddr->ddr_sdram_mode_6 = (0 924 | ((esdmode2 & 0xFFFF) << 16) 925 | ((esdmode3 & 0xFFFF) << 0) 926 ); 927 break; 928 case 3: 929 ddr->ddr_sdram_mode_8 = (0 930 | ((esdmode2 & 0xFFFF) << 16) 931 | ((esdmode3 & 0xFFFF) << 0) 932 ); 933 break; 934 } 935 } 936 debug("FSLDDR: ddr_sdram_mode_4 = 0x%08x\n", 937 ddr->ddr_sdram_mode_4); 938 debug("FSLDDR: ddr_sdram_mode_6 = 0x%08x\n", 939 ddr->ddr_sdram_mode_6); 940 debug("FSLDDR: ddr_sdram_mode_8 = 0x%08x\n", 941 ddr->ddr_sdram_mode_8); 942 } 943 } 944 #elif defined(CONFIG_SYS_FSL_DDR3) 945 /* DDR SDRAM Mode configuration 2 (DDR_SDRAM_MODE_2) */ 946 static void set_ddr_sdram_mode_2(fsl_ddr_cfg_regs_t *ddr, 947 const memctl_options_t *popts, 948 const common_timing_params_t *common_dimm, 949 const unsigned int unq_mrs_en) 950 { 951 unsigned short esdmode2 = 0; /* Extended SDRAM mode 2 */ 952 unsigned short esdmode3 = 0; /* Extended SDRAM mode 3 */ 953 int i; 954 unsigned int rtt_wr = 0; /* Rtt_WR - dynamic ODT off */ 955 unsigned int srt = 0; /* self-refresh temerature, normal range */ 956 unsigned int asr = 0; /* auto self-refresh disable */ 957 unsigned int cwl = compute_cas_write_latency() - 5; 958 unsigned int pasr = 0; /* partial array self refresh disable */ 959 960 if (popts->rtt_override) 961 rtt_wr = popts->rtt_wr_override_value; 962 else 963 rtt_wr = popts->cs_local_opts[0].odt_rtt_wr; 964 965 if (common_dimm->extended_op_srt) 966 srt = common_dimm->extended_op_srt; 967 968 esdmode2 = (0 969 | ((rtt_wr & 0x3) << 9) 970 | ((srt & 0x1) << 7) 971 | ((asr & 0x1) << 6) 972 | ((cwl & 0x7) << 3) 973 | ((pasr & 0x7) << 0)); 974 ddr->ddr_sdram_mode_2 = (0 975 | ((esdmode2 & 0xFFFF) << 16) 976 | ((esdmode3 & 0xFFFF) << 0) 977 ); 978 debug("FSLDDR: ddr_sdram_mode_2 = 0x%08x\n", ddr->ddr_sdram_mode_2); 979 980 if (unq_mrs_en) { /* unique mode registers are supported */ 981 for (i = 1; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) { 982 if (popts->rtt_override) 983 rtt_wr = popts->rtt_wr_override_value; 984 else 985 rtt_wr = popts->cs_local_opts[i].odt_rtt_wr; 986 987 esdmode2 &= 0xF9FF; /* clear bit 10, 9 */ 988 esdmode2 |= (rtt_wr & 0x3) << 9; 989 switch (i) { 990 case 1: 991 ddr->ddr_sdram_mode_4 = (0 992 | ((esdmode2 & 0xFFFF) << 16) 993 | ((esdmode3 & 0xFFFF) << 0) 994 ); 995 break; 996 case 2: 997 ddr->ddr_sdram_mode_6 = (0 998 | ((esdmode2 & 0xFFFF) << 16) 999 | ((esdmode3 & 0xFFFF) << 0) 1000 ); 1001 break; 1002 case 3: 1003 ddr->ddr_sdram_mode_8 = (0 1004 | ((esdmode2 & 0xFFFF) << 16) 1005 | ((esdmode3 & 0xFFFF) << 0) 1006 ); 1007 break; 1008 } 1009 } 1010 debug("FSLDDR: ddr_sdram_mode_4 = 0x%08x\n", 1011 ddr->ddr_sdram_mode_4); 1012 debug("FSLDDR: ddr_sdram_mode_6 = 0x%08x\n", 1013 ddr->ddr_sdram_mode_6); 1014 debug("FSLDDR: ddr_sdram_mode_8 = 0x%08x\n", 1015 ddr->ddr_sdram_mode_8); 1016 } 1017 } 1018 1019 #else /* for DDR2 and DDR1 */ 1020 /* DDR SDRAM Mode configuration 2 (DDR_SDRAM_MODE_2) */ 1021 static void set_ddr_sdram_mode_2(fsl_ddr_cfg_regs_t *ddr, 1022 const memctl_options_t *popts, 1023 const common_timing_params_t *common_dimm, 1024 const unsigned int unq_mrs_en) 1025 { 1026 unsigned short esdmode2 = 0; /* Extended SDRAM mode 2 */ 1027 unsigned short esdmode3 = 0; /* Extended SDRAM mode 3 */ 1028 1029 ddr->ddr_sdram_mode_2 = (0 1030 | ((esdmode2 & 0xFFFF) << 16) 1031 | ((esdmode3 & 0xFFFF) << 0) 1032 ); 1033 debug("FSLDDR: ddr_sdram_mode_2 = 0x%08x\n", ddr->ddr_sdram_mode_2); 1034 } 1035 #endif 1036 1037 #ifdef CONFIG_SYS_FSL_DDR4 1038 /* DDR SDRAM Mode configuration 9 (DDR_SDRAM_MODE_9) */ 1039 static void set_ddr_sdram_mode_9(fsl_ddr_cfg_regs_t *ddr, 1040 const memctl_options_t *popts, 1041 const common_timing_params_t *common_dimm, 1042 const unsigned int unq_mrs_en) 1043 { 1044 int i; 1045 unsigned short esdmode4 = 0; /* Extended SDRAM mode 4 */ 1046 unsigned short esdmode5; /* Extended SDRAM mode 5 */ 1047 1048 esdmode5 = 0x00000400; /* Data mask enabled */ 1049 1050 ddr->ddr_sdram_mode_9 = (0 1051 | ((esdmode4 & 0xffff) << 16) 1052 | ((esdmode5 & 0xffff) << 0) 1053 ); 1054 debug("FSLDDR: ddr_sdram_mode_9) = 0x%08x\n", ddr->ddr_sdram_mode_9); 1055 if (unq_mrs_en) { /* unique mode registers are supported */ 1056 for (i = 1; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) { 1057 switch (i) { 1058 case 1: 1059 ddr->ddr_sdram_mode_11 = (0 1060 | ((esdmode4 & 0xFFFF) << 16) 1061 | ((esdmode5 & 0xFFFF) << 0) 1062 ); 1063 break; 1064 case 2: 1065 ddr->ddr_sdram_mode_13 = (0 1066 | ((esdmode4 & 0xFFFF) << 16) 1067 | ((esdmode5 & 0xFFFF) << 0) 1068 ); 1069 break; 1070 case 3: 1071 ddr->ddr_sdram_mode_15 = (0 1072 | ((esdmode4 & 0xFFFF) << 16) 1073 | ((esdmode5 & 0xFFFF) << 0) 1074 ); 1075 break; 1076 } 1077 } 1078 debug("FSLDDR: ddr_sdram_mode_11 = 0x%08x\n", 1079 ddr->ddr_sdram_mode_11); 1080 debug("FSLDDR: ddr_sdram_mode_13 = 0x%08x\n", 1081 ddr->ddr_sdram_mode_13); 1082 debug("FSLDDR: ddr_sdram_mode_15 = 0x%08x\n", 1083 ddr->ddr_sdram_mode_15); 1084 } 1085 } 1086 1087 /* DDR SDRAM Mode configuration 10 (DDR_SDRAM_MODE_10) */ 1088 static void set_ddr_sdram_mode_10(fsl_ddr_cfg_regs_t *ddr, 1089 const memctl_options_t *popts, 1090 const common_timing_params_t *common_dimm, 1091 const unsigned int unq_mrs_en) 1092 { 1093 int i; 1094 unsigned short esdmode6 = 0; /* Extended SDRAM mode 6 */ 1095 unsigned short esdmode7 = 0; /* Extended SDRAM mode 7 */ 1096 unsigned int tccdl_min = picos_to_mclk(common_dimm->tccdl_ps); 1097 1098 esdmode6 = ((tccdl_min - 4) & 0x7) << 10; 1099 1100 ddr->ddr_sdram_mode_10 = (0 1101 | ((esdmode6 & 0xffff) << 16) 1102 | ((esdmode7 & 0xffff) << 0) 1103 ); 1104 debug("FSLDDR: ddr_sdram_mode_10) = 0x%08x\n", ddr->ddr_sdram_mode_10); 1105 if (unq_mrs_en) { /* unique mode registers are supported */ 1106 for (i = 1; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) { 1107 switch (i) { 1108 case 1: 1109 ddr->ddr_sdram_mode_12 = (0 1110 | ((esdmode6 & 0xFFFF) << 16) 1111 | ((esdmode7 & 0xFFFF) << 0) 1112 ); 1113 break; 1114 case 2: 1115 ddr->ddr_sdram_mode_14 = (0 1116 | ((esdmode6 & 0xFFFF) << 16) 1117 | ((esdmode7 & 0xFFFF) << 0) 1118 ); 1119 break; 1120 case 3: 1121 ddr->ddr_sdram_mode_16 = (0 1122 | ((esdmode6 & 0xFFFF) << 16) 1123 | ((esdmode7 & 0xFFFF) << 0) 1124 ); 1125 break; 1126 } 1127 } 1128 debug("FSLDDR: ddr_sdram_mode_12 = 0x%08x\n", 1129 ddr->ddr_sdram_mode_12); 1130 debug("FSLDDR: ddr_sdram_mode_14 = 0x%08x\n", 1131 ddr->ddr_sdram_mode_14); 1132 debug("FSLDDR: ddr_sdram_mode_16 = 0x%08x\n", 1133 ddr->ddr_sdram_mode_16); 1134 } 1135 } 1136 1137 #endif 1138 1139 /* DDR SDRAM Interval Configuration (DDR_SDRAM_INTERVAL) */ 1140 static void set_ddr_sdram_interval(fsl_ddr_cfg_regs_t *ddr, 1141 const memctl_options_t *popts, 1142 const common_timing_params_t *common_dimm) 1143 { 1144 unsigned int refint; /* Refresh interval */ 1145 unsigned int bstopre; /* Precharge interval */ 1146 1147 refint = picos_to_mclk(common_dimm->refresh_rate_ps); 1148 1149 bstopre = popts->bstopre; 1150 1151 /* refint field used 0x3FFF in earlier controllers */ 1152 ddr->ddr_sdram_interval = (0 1153 | ((refint & 0xFFFF) << 16) 1154 | ((bstopre & 0x3FFF) << 0) 1155 ); 1156 debug("FSLDDR: ddr_sdram_interval = 0x%08x\n", ddr->ddr_sdram_interval); 1157 } 1158 1159 #ifdef CONFIG_SYS_FSL_DDR4 1160 /* DDR SDRAM Mode configuration set (DDR_SDRAM_MODE) */ 1161 static void set_ddr_sdram_mode(fsl_ddr_cfg_regs_t *ddr, 1162 const memctl_options_t *popts, 1163 const common_timing_params_t *common_dimm, 1164 unsigned int cas_latency, 1165 unsigned int additive_latency, 1166 const unsigned int unq_mrs_en) 1167 { 1168 int i; 1169 unsigned short esdmode; /* Extended SDRAM mode */ 1170 unsigned short sdmode; /* SDRAM mode */ 1171 1172 /* Mode Register - MR1 */ 1173 unsigned int qoff = 0; /* Output buffer enable 0=yes, 1=no */ 1174 unsigned int tdqs_en = 0; /* TDQS Enable: 0=no, 1=yes */ 1175 unsigned int rtt; 1176 unsigned int wrlvl_en = 0; /* Write level enable: 0=no, 1=yes */ 1177 unsigned int al = 0; /* Posted CAS# additive latency (AL) */ 1178 unsigned int dic = 0; /* Output driver impedance, 40ohm */ 1179 unsigned int dll_en = 1; /* DLL Enable 1=Enable (Normal), 1180 0=Disable (Test/Debug) */ 1181 1182 /* Mode Register - MR0 */ 1183 unsigned int wr = 0; /* Write Recovery */ 1184 unsigned int dll_rst; /* DLL Reset */ 1185 unsigned int mode; /* Normal=0 or Test=1 */ 1186 unsigned int caslat = 4;/* CAS# latency, default set as 6 cycles */ 1187 /* BT: Burst Type (0=Nibble Sequential, 1=Interleaved) */ 1188 unsigned int bt; 1189 unsigned int bl; /* BL: Burst Length */ 1190 1191 unsigned int wr_mclk; 1192 /* DDR4 support WR 10, 12, 14, 16, 18, 20, 24 */ 1193 static const u8 wr_table[] = { 1194 0, 1, 1, 2, 2, 3, 3, 4, 4, 5, 5, 6, 6, 6, 6}; 1195 /* DDR4 support CAS 9, 10, 11, 12, 13, 14, 15, 16, 18, 20, 22, 24 */ 1196 static const u8 cas_latency_table[] = { 1197 0, 1, 2, 3, 4, 5, 6, 7, 8, 8, 1198 9, 9, 10, 10, 11, 11}; 1199 1200 if (popts->rtt_override) 1201 rtt = popts->rtt_override_value; 1202 else 1203 rtt = popts->cs_local_opts[0].odt_rtt_norm; 1204 1205 if (additive_latency == (cas_latency - 1)) 1206 al = 1; 1207 if (additive_latency == (cas_latency - 2)) 1208 al = 2; 1209 1210 if (popts->quad_rank_present) 1211 dic = 1; /* output driver impedance 240/7 ohm */ 1212 1213 /* 1214 * The esdmode value will also be used for writing 1215 * MR1 during write leveling for DDR3, although the 1216 * bits specifically related to the write leveling 1217 * scheme will be handled automatically by the DDR 1218 * controller. so we set the wrlvl_en = 0 here. 1219 */ 1220 esdmode = (0 1221 | ((qoff & 0x1) << 12) 1222 | ((tdqs_en & 0x1) << 11) 1223 | ((rtt & 0x7) << 8) 1224 | ((wrlvl_en & 0x1) << 7) 1225 | ((al & 0x3) << 3) 1226 | ((dic & 0x3) << 1) /* DIC field is split */ 1227 | ((dll_en & 0x1) << 0) 1228 ); 1229 1230 /* 1231 * DLL control for precharge PD 1232 * 0=slow exit DLL off (tXPDLL) 1233 * 1=fast exit DLL on (tXP) 1234 */ 1235 1236 wr_mclk = picos_to_mclk(common_dimm->twr_ps); 1237 if (wr_mclk <= 24) { 1238 wr = wr_table[wr_mclk - 10]; 1239 } else { 1240 printf("Error: unsupported write recovery for mode register wr_mclk = %d\n", 1241 wr_mclk); 1242 } 1243 1244 dll_rst = 0; /* dll no reset */ 1245 mode = 0; /* normal mode */ 1246 1247 /* look up table to get the cas latency bits */ 1248 if (cas_latency >= 9 && cas_latency <= 24) 1249 caslat = cas_latency_table[cas_latency - 9]; 1250 else 1251 printf("Error: unsupported cas latency for mode register\n"); 1252 1253 bt = 0; /* Nibble sequential */ 1254 1255 switch (popts->burst_length) { 1256 case DDR_BL8: 1257 bl = 0; 1258 break; 1259 case DDR_OTF: 1260 bl = 1; 1261 break; 1262 case DDR_BC4: 1263 bl = 2; 1264 break; 1265 default: 1266 printf("Error: invalid burst length of %u specified. ", 1267 popts->burst_length); 1268 puts("Defaulting to on-the-fly BC4 or BL8 beats.\n"); 1269 bl = 1; 1270 break; 1271 } 1272 1273 sdmode = (0 1274 | ((wr & 0x7) << 9) 1275 | ((dll_rst & 0x1) << 8) 1276 | ((mode & 0x1) << 7) 1277 | (((caslat >> 1) & 0x7) << 4) 1278 | ((bt & 0x1) << 3) 1279 | ((caslat & 1) << 2) 1280 | ((bl & 0x3) << 0) 1281 ); 1282 1283 ddr->ddr_sdram_mode = (0 1284 | ((esdmode & 0xFFFF) << 16) 1285 | ((sdmode & 0xFFFF) << 0) 1286 ); 1287 1288 debug("FSLDDR: ddr_sdram_mode = 0x%08x\n", ddr->ddr_sdram_mode); 1289 1290 if (unq_mrs_en) { /* unique mode registers are supported */ 1291 for (i = 1; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) { 1292 if (popts->rtt_override) 1293 rtt = popts->rtt_override_value; 1294 else 1295 rtt = popts->cs_local_opts[i].odt_rtt_norm; 1296 1297 esdmode &= 0xF8FF; /* clear bit 10,9,8 for rtt */ 1298 esdmode |= (rtt & 0x7) << 8; 1299 switch (i) { 1300 case 1: 1301 ddr->ddr_sdram_mode_3 = (0 1302 | ((esdmode & 0xFFFF) << 16) 1303 | ((sdmode & 0xFFFF) << 0) 1304 ); 1305 break; 1306 case 2: 1307 ddr->ddr_sdram_mode_5 = (0 1308 | ((esdmode & 0xFFFF) << 16) 1309 | ((sdmode & 0xFFFF) << 0) 1310 ); 1311 break; 1312 case 3: 1313 ddr->ddr_sdram_mode_7 = (0 1314 | ((esdmode & 0xFFFF) << 16) 1315 | ((sdmode & 0xFFFF) << 0) 1316 ); 1317 break; 1318 } 1319 } 1320 debug("FSLDDR: ddr_sdram_mode_3 = 0x%08x\n", 1321 ddr->ddr_sdram_mode_3); 1322 debug("FSLDDR: ddr_sdram_mode_5 = 0x%08x\n", 1323 ddr->ddr_sdram_mode_5); 1324 debug("FSLDDR: ddr_sdram_mode_5 = 0x%08x\n", 1325 ddr->ddr_sdram_mode_5); 1326 } 1327 } 1328 1329 #elif defined(CONFIG_SYS_FSL_DDR3) 1330 /* DDR SDRAM Mode configuration set (DDR_SDRAM_MODE) */ 1331 static void set_ddr_sdram_mode(fsl_ddr_cfg_regs_t *ddr, 1332 const memctl_options_t *popts, 1333 const common_timing_params_t *common_dimm, 1334 unsigned int cas_latency, 1335 unsigned int additive_latency, 1336 const unsigned int unq_mrs_en) 1337 { 1338 int i; 1339 unsigned short esdmode; /* Extended SDRAM mode */ 1340 unsigned short sdmode; /* SDRAM mode */ 1341 1342 /* Mode Register - MR1 */ 1343 unsigned int qoff = 0; /* Output buffer enable 0=yes, 1=no */ 1344 unsigned int tdqs_en = 0; /* TDQS Enable: 0=no, 1=yes */ 1345 unsigned int rtt; 1346 unsigned int wrlvl_en = 0; /* Write level enable: 0=no, 1=yes */ 1347 unsigned int al = 0; /* Posted CAS# additive latency (AL) */ 1348 unsigned int dic = 0; /* Output driver impedance, 40ohm */ 1349 unsigned int dll_en = 0; /* DLL Enable 0=Enable (Normal), 1350 1=Disable (Test/Debug) */ 1351 1352 /* Mode Register - MR0 */ 1353 unsigned int dll_on; /* DLL control for precharge PD, 0=off, 1=on */ 1354 unsigned int wr = 0; /* Write Recovery */ 1355 unsigned int dll_rst; /* DLL Reset */ 1356 unsigned int mode; /* Normal=0 or Test=1 */ 1357 unsigned int caslat = 4;/* CAS# latency, default set as 6 cycles */ 1358 /* BT: Burst Type (0=Nibble Sequential, 1=Interleaved) */ 1359 unsigned int bt; 1360 unsigned int bl; /* BL: Burst Length */ 1361 1362 unsigned int wr_mclk; 1363 /* 1364 * DDR_SDRAM_MODE doesn't support 9,11,13,15 1365 * Please refer JEDEC Standard No. 79-3E for Mode Register MR0 1366 * for this table 1367 */ 1368 static const u8 wr_table[] = {1, 2, 3, 4, 5, 5, 6, 6, 7, 7, 0, 0}; 1369 1370 if (popts->rtt_override) 1371 rtt = popts->rtt_override_value; 1372 else 1373 rtt = popts->cs_local_opts[0].odt_rtt_norm; 1374 1375 if (additive_latency == (cas_latency - 1)) 1376 al = 1; 1377 if (additive_latency == (cas_latency - 2)) 1378 al = 2; 1379 1380 if (popts->quad_rank_present) 1381 dic = 1; /* output driver impedance 240/7 ohm */ 1382 1383 /* 1384 * The esdmode value will also be used for writing 1385 * MR1 during write leveling for DDR3, although the 1386 * bits specifically related to the write leveling 1387 * scheme will be handled automatically by the DDR 1388 * controller. so we set the wrlvl_en = 0 here. 1389 */ 1390 esdmode = (0 1391 | ((qoff & 0x1) << 12) 1392 | ((tdqs_en & 0x1) << 11) 1393 | ((rtt & 0x4) << 7) /* rtt field is split */ 1394 | ((wrlvl_en & 0x1) << 7) 1395 | ((rtt & 0x2) << 5) /* rtt field is split */ 1396 | ((dic & 0x2) << 4) /* DIC field is split */ 1397 | ((al & 0x3) << 3) 1398 | ((rtt & 0x1) << 2) /* rtt field is split */ 1399 | ((dic & 0x1) << 1) /* DIC field is split */ 1400 | ((dll_en & 0x1) << 0) 1401 ); 1402 1403 /* 1404 * DLL control for precharge PD 1405 * 0=slow exit DLL off (tXPDLL) 1406 * 1=fast exit DLL on (tXP) 1407 */ 1408 dll_on = 1; 1409 1410 wr_mclk = picos_to_mclk(common_dimm->twr_ps); 1411 if (wr_mclk <= 16) { 1412 wr = wr_table[wr_mclk - 5]; 1413 } else { 1414 printf("Error: unsupported write recovery for mode register " 1415 "wr_mclk = %d\n", wr_mclk); 1416 } 1417 1418 dll_rst = 0; /* dll no reset */ 1419 mode = 0; /* normal mode */ 1420 1421 /* look up table to get the cas latency bits */ 1422 if (cas_latency >= 5 && cas_latency <= 16) { 1423 unsigned char cas_latency_table[] = { 1424 0x2, /* 5 clocks */ 1425 0x4, /* 6 clocks */ 1426 0x6, /* 7 clocks */ 1427 0x8, /* 8 clocks */ 1428 0xa, /* 9 clocks */ 1429 0xc, /* 10 clocks */ 1430 0xe, /* 11 clocks */ 1431 0x1, /* 12 clocks */ 1432 0x3, /* 13 clocks */ 1433 0x5, /* 14 clocks */ 1434 0x7, /* 15 clocks */ 1435 0x9, /* 16 clocks */ 1436 }; 1437 caslat = cas_latency_table[cas_latency - 5]; 1438 } else { 1439 printf("Error: unsupported cas latency for mode register\n"); 1440 } 1441 1442 bt = 0; /* Nibble sequential */ 1443 1444 switch (popts->burst_length) { 1445 case DDR_BL8: 1446 bl = 0; 1447 break; 1448 case DDR_OTF: 1449 bl = 1; 1450 break; 1451 case DDR_BC4: 1452 bl = 2; 1453 break; 1454 default: 1455 printf("Error: invalid burst length of %u specified. " 1456 " Defaulting to on-the-fly BC4 or BL8 beats.\n", 1457 popts->burst_length); 1458 bl = 1; 1459 break; 1460 } 1461 1462 sdmode = (0 1463 | ((dll_on & 0x1) << 12) 1464 | ((wr & 0x7) << 9) 1465 | ((dll_rst & 0x1) << 8) 1466 | ((mode & 0x1) << 7) 1467 | (((caslat >> 1) & 0x7) << 4) 1468 | ((bt & 0x1) << 3) 1469 | ((caslat & 1) << 2) 1470 | ((bl & 0x3) << 0) 1471 ); 1472 1473 ddr->ddr_sdram_mode = (0 1474 | ((esdmode & 0xFFFF) << 16) 1475 | ((sdmode & 0xFFFF) << 0) 1476 ); 1477 1478 debug("FSLDDR: ddr_sdram_mode = 0x%08x\n", ddr->ddr_sdram_mode); 1479 1480 if (unq_mrs_en) { /* unique mode registers are supported */ 1481 for (i = 1; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) { 1482 if (popts->rtt_override) 1483 rtt = popts->rtt_override_value; 1484 else 1485 rtt = popts->cs_local_opts[i].odt_rtt_norm; 1486 1487 esdmode &= 0xFDBB; /* clear bit 9,6,2 */ 1488 esdmode |= (0 1489 | ((rtt & 0x4) << 7) /* rtt field is split */ 1490 | ((rtt & 0x2) << 5) /* rtt field is split */ 1491 | ((rtt & 0x1) << 2) /* rtt field is split */ 1492 ); 1493 switch (i) { 1494 case 1: 1495 ddr->ddr_sdram_mode_3 = (0 1496 | ((esdmode & 0xFFFF) << 16) 1497 | ((sdmode & 0xFFFF) << 0) 1498 ); 1499 break; 1500 case 2: 1501 ddr->ddr_sdram_mode_5 = (0 1502 | ((esdmode & 0xFFFF) << 16) 1503 | ((sdmode & 0xFFFF) << 0) 1504 ); 1505 break; 1506 case 3: 1507 ddr->ddr_sdram_mode_7 = (0 1508 | ((esdmode & 0xFFFF) << 16) 1509 | ((sdmode & 0xFFFF) << 0) 1510 ); 1511 break; 1512 } 1513 } 1514 debug("FSLDDR: ddr_sdram_mode_3 = 0x%08x\n", 1515 ddr->ddr_sdram_mode_3); 1516 debug("FSLDDR: ddr_sdram_mode_5 = 0x%08x\n", 1517 ddr->ddr_sdram_mode_5); 1518 debug("FSLDDR: ddr_sdram_mode_5 = 0x%08x\n", 1519 ddr->ddr_sdram_mode_5); 1520 } 1521 } 1522 1523 #else /* !CONFIG_SYS_FSL_DDR3 */ 1524 1525 /* DDR SDRAM Mode configuration set (DDR_SDRAM_MODE) */ 1526 static void set_ddr_sdram_mode(fsl_ddr_cfg_regs_t *ddr, 1527 const memctl_options_t *popts, 1528 const common_timing_params_t *common_dimm, 1529 unsigned int cas_latency, 1530 unsigned int additive_latency, 1531 const unsigned int unq_mrs_en) 1532 { 1533 unsigned short esdmode; /* Extended SDRAM mode */ 1534 unsigned short sdmode; /* SDRAM mode */ 1535 1536 /* 1537 * FIXME: This ought to be pre-calculated in a 1538 * technology-specific routine, 1539 * e.g. compute_DDR2_mode_register(), and then the 1540 * sdmode and esdmode passed in as part of common_dimm. 1541 */ 1542 1543 /* Extended Mode Register */ 1544 unsigned int mrs = 0; /* Mode Register Set */ 1545 unsigned int outputs = 0; /* 0=Enabled, 1=Disabled */ 1546 unsigned int rdqs_en = 0; /* RDQS Enable: 0=no, 1=yes */ 1547 unsigned int dqs_en = 0; /* DQS# Enable: 0=enable, 1=disable */ 1548 unsigned int ocd = 0; /* 0x0=OCD not supported, 1549 0x7=OCD default state */ 1550 unsigned int rtt; 1551 unsigned int al; /* Posted CAS# additive latency (AL) */ 1552 unsigned int ods = 0; /* Output Drive Strength: 1553 0 = Full strength (18ohm) 1554 1 = Reduced strength (4ohm) */ 1555 unsigned int dll_en = 0; /* DLL Enable 0=Enable (Normal), 1556 1=Disable (Test/Debug) */ 1557 1558 /* Mode Register (MR) */ 1559 unsigned int mr; /* Mode Register Definition */ 1560 unsigned int pd; /* Power-Down Mode */ 1561 unsigned int wr; /* Write Recovery */ 1562 unsigned int dll_res; /* DLL Reset */ 1563 unsigned int mode; /* Normal=0 or Test=1 */ 1564 unsigned int caslat = 0;/* CAS# latency */ 1565 /* BT: Burst Type (0=Sequential, 1=Interleaved) */ 1566 unsigned int bt; 1567 unsigned int bl; /* BL: Burst Length */ 1568 1569 dqs_en = !popts->dqs_config; 1570 rtt = fsl_ddr_get_rtt(); 1571 1572 al = additive_latency; 1573 1574 esdmode = (0 1575 | ((mrs & 0x3) << 14) 1576 | ((outputs & 0x1) << 12) 1577 | ((rdqs_en & 0x1) << 11) 1578 | ((dqs_en & 0x1) << 10) 1579 | ((ocd & 0x7) << 7) 1580 | ((rtt & 0x2) << 5) /* rtt field is split */ 1581 | ((al & 0x7) << 3) 1582 | ((rtt & 0x1) << 2) /* rtt field is split */ 1583 | ((ods & 0x1) << 1) 1584 | ((dll_en & 0x1) << 0) 1585 ); 1586 1587 mr = 0; /* FIXME: CHECKME */ 1588 1589 /* 1590 * 0 = Fast Exit (Normal) 1591 * 1 = Slow Exit (Low Power) 1592 */ 1593 pd = 0; 1594 1595 #if defined(CONFIG_SYS_FSL_DDR1) 1596 wr = 0; /* Historical */ 1597 #elif defined(CONFIG_SYS_FSL_DDR2) 1598 wr = picos_to_mclk(common_dimm->twr_ps); 1599 #endif 1600 dll_res = 0; 1601 mode = 0; 1602 1603 #if defined(CONFIG_SYS_FSL_DDR1) 1604 if (1 <= cas_latency && cas_latency <= 4) { 1605 unsigned char mode_caslat_table[4] = { 1606 0x5, /* 1.5 clocks */ 1607 0x2, /* 2.0 clocks */ 1608 0x6, /* 2.5 clocks */ 1609 0x3 /* 3.0 clocks */ 1610 }; 1611 caslat = mode_caslat_table[cas_latency - 1]; 1612 } else { 1613 printf("Warning: unknown cas_latency %d\n", cas_latency); 1614 } 1615 #elif defined(CONFIG_SYS_FSL_DDR2) 1616 caslat = cas_latency; 1617 #endif 1618 bt = 0; 1619 1620 switch (popts->burst_length) { 1621 case DDR_BL4: 1622 bl = 2; 1623 break; 1624 case DDR_BL8: 1625 bl = 3; 1626 break; 1627 default: 1628 printf("Error: invalid burst length of %u specified. " 1629 " Defaulting to 4 beats.\n", 1630 popts->burst_length); 1631 bl = 2; 1632 break; 1633 } 1634 1635 sdmode = (0 1636 | ((mr & 0x3) << 14) 1637 | ((pd & 0x1) << 12) 1638 | ((wr & 0x7) << 9) 1639 | ((dll_res & 0x1) << 8) 1640 | ((mode & 0x1) << 7) 1641 | ((caslat & 0x7) << 4) 1642 | ((bt & 0x1) << 3) 1643 | ((bl & 0x7) << 0) 1644 ); 1645 1646 ddr->ddr_sdram_mode = (0 1647 | ((esdmode & 0xFFFF) << 16) 1648 | ((sdmode & 0xFFFF) << 0) 1649 ); 1650 debug("FSLDDR: ddr_sdram_mode = 0x%08x\n", ddr->ddr_sdram_mode); 1651 } 1652 #endif 1653 1654 /* DDR SDRAM Data Initialization (DDR_DATA_INIT) */ 1655 static void set_ddr_data_init(fsl_ddr_cfg_regs_t *ddr) 1656 { 1657 unsigned int init_value; /* Initialization value */ 1658 1659 #ifdef CONFIG_MEM_INIT_VALUE 1660 init_value = CONFIG_MEM_INIT_VALUE; 1661 #else 1662 init_value = 0xDEADBEEF; 1663 #endif 1664 ddr->ddr_data_init = init_value; 1665 } 1666 1667 /* 1668 * DDR SDRAM Clock Control (DDR_SDRAM_CLK_CNTL) 1669 * The old controller on the 8540/60 doesn't have this register. 1670 * Hope it's OK to set it (to 0) anyway. 1671 */ 1672 static void set_ddr_sdram_clk_cntl(fsl_ddr_cfg_regs_t *ddr, 1673 const memctl_options_t *popts) 1674 { 1675 unsigned int clk_adjust; /* Clock adjust */ 1676 1677 clk_adjust = popts->clk_adjust; 1678 ddr->ddr_sdram_clk_cntl = (clk_adjust & 0xF) << 23; 1679 debug("FSLDDR: clk_cntl = 0x%08x\n", ddr->ddr_sdram_clk_cntl); 1680 } 1681 1682 /* DDR Initialization Address (DDR_INIT_ADDR) */ 1683 static void set_ddr_init_addr(fsl_ddr_cfg_regs_t *ddr) 1684 { 1685 unsigned int init_addr = 0; /* Initialization address */ 1686 1687 ddr->ddr_init_addr = init_addr; 1688 } 1689 1690 /* DDR Initialization Address (DDR_INIT_EXT_ADDR) */ 1691 static void set_ddr_init_ext_addr(fsl_ddr_cfg_regs_t *ddr) 1692 { 1693 unsigned int uia = 0; /* Use initialization address */ 1694 unsigned int init_ext_addr = 0; /* Initialization address */ 1695 1696 ddr->ddr_init_ext_addr = (0 1697 | ((uia & 0x1) << 31) 1698 | (init_ext_addr & 0xF) 1699 ); 1700 } 1701 1702 /* DDR SDRAM Timing Configuration 4 (TIMING_CFG_4) */ 1703 static void set_timing_cfg_4(fsl_ddr_cfg_regs_t *ddr, 1704 const memctl_options_t *popts) 1705 { 1706 unsigned int rwt = 0; /* Read-to-write turnaround for same CS */ 1707 unsigned int wrt = 0; /* Write-to-read turnaround for same CS */ 1708 unsigned int rrt = 0; /* Read-to-read turnaround for same CS */ 1709 unsigned int wwt = 0; /* Write-to-write turnaround for same CS */ 1710 unsigned int dll_lock = 0; /* DDR SDRAM DLL Lock Time */ 1711 1712 #if defined(CONFIG_SYS_FSL_DDR3) || defined(CONFIG_SYS_FSL_DDR4) 1713 if (popts->burst_length == DDR_BL8) { 1714 /* We set BL/2 for fixed BL8 */ 1715 rrt = 0; /* BL/2 clocks */ 1716 wwt = 0; /* BL/2 clocks */ 1717 } else { 1718 /* We need to set BL/2 + 2 to BC4 and OTF */ 1719 rrt = 2; /* BL/2 + 2 clocks */ 1720 wwt = 2; /* BL/2 + 2 clocks */ 1721 } 1722 #endif 1723 1724 #ifdef CONFIG_SYS_FSL_DDR4 1725 dll_lock = 2; /* tDLLK = 1024 clocks */ 1726 #elif defined(CONFIG_SYS_FSL_DDR3) 1727 dll_lock = 1; /* tDLLK = 512 clocks from spec */ 1728 #endif 1729 ddr->timing_cfg_4 = (0 1730 | ((rwt & 0xf) << 28) 1731 | ((wrt & 0xf) << 24) 1732 | ((rrt & 0xf) << 20) 1733 | ((wwt & 0xf) << 16) 1734 | (dll_lock & 0x3) 1735 ); 1736 debug("FSLDDR: timing_cfg_4 = 0x%08x\n", ddr->timing_cfg_4); 1737 } 1738 1739 /* DDR SDRAM Timing Configuration 5 (TIMING_CFG_5) */ 1740 static void set_timing_cfg_5(fsl_ddr_cfg_regs_t *ddr, unsigned int cas_latency) 1741 { 1742 unsigned int rodt_on = 0; /* Read to ODT on */ 1743 unsigned int rodt_off = 0; /* Read to ODT off */ 1744 unsigned int wodt_on = 0; /* Write to ODT on */ 1745 unsigned int wodt_off = 0; /* Write to ODT off */ 1746 1747 #if defined(CONFIG_SYS_FSL_DDR3) || defined(CONFIG_SYS_FSL_DDR4) 1748 unsigned int wr_lat = ((ddr->timing_cfg_2 & 0x00780000) >> 19) + 1749 ((ddr->timing_cfg_2 & 0x00040000) >> 14); 1750 /* rodt_on = timing_cfg_1[caslat] - timing_cfg_2[wrlat] + 1 */ 1751 if (cas_latency >= wr_lat) 1752 rodt_on = cas_latency - wr_lat + 1; 1753 rodt_off = 4; /* 4 clocks */ 1754 wodt_on = 1; /* 1 clocks */ 1755 wodt_off = 4; /* 4 clocks */ 1756 #endif 1757 1758 ddr->timing_cfg_5 = (0 1759 | ((rodt_on & 0x1f) << 24) 1760 | ((rodt_off & 0x7) << 20) 1761 | ((wodt_on & 0x1f) << 12) 1762 | ((wodt_off & 0x7) << 8) 1763 ); 1764 debug("FSLDDR: timing_cfg_5 = 0x%08x\n", ddr->timing_cfg_5); 1765 } 1766 1767 #ifdef CONFIG_SYS_FSL_DDR4 1768 static void set_timing_cfg_6(fsl_ddr_cfg_regs_t *ddr) 1769 { 1770 unsigned int hs_caslat = 0; 1771 unsigned int hs_wrlat = 0; 1772 unsigned int hs_wrrec = 0; 1773 unsigned int hs_clkadj = 0; 1774 unsigned int hs_wrlvl_start = 0; 1775 1776 ddr->timing_cfg_6 = (0 1777 | ((hs_caslat & 0x1f) << 24) 1778 | ((hs_wrlat & 0x1f) << 19) 1779 | ((hs_wrrec & 0x1f) << 12) 1780 | ((hs_clkadj & 0x1f) << 6) 1781 | ((hs_wrlvl_start & 0x1f) << 0) 1782 ); 1783 debug("FSLDDR: timing_cfg_6 = 0x%08x\n", ddr->timing_cfg_6); 1784 } 1785 1786 static void set_timing_cfg_7(fsl_ddr_cfg_regs_t *ddr, 1787 const common_timing_params_t *common_dimm) 1788 { 1789 unsigned int txpr, tcksre, tcksrx; 1790 unsigned int cke_rst, cksre, cksrx, par_lat, cs_to_cmd; 1791 1792 txpr = max(5, picos_to_mclk(common_dimm->trfc1_ps + 10000)); 1793 tcksre = max(5, picos_to_mclk(10000)); 1794 tcksrx = max(5, picos_to_mclk(10000)); 1795 par_lat = 0; 1796 cs_to_cmd = 0; 1797 1798 if (txpr <= 200) 1799 cke_rst = 0; 1800 else if (txpr <= 256) 1801 cke_rst = 1; 1802 else if (txpr <= 512) 1803 cke_rst = 2; 1804 else 1805 cke_rst = 3; 1806 1807 if (tcksre <= 19) 1808 cksre = tcksre - 5; 1809 else 1810 cksre = 15; 1811 1812 if (tcksrx <= 19) 1813 cksrx = tcksrx - 5; 1814 else 1815 cksrx = 15; 1816 1817 ddr->timing_cfg_7 = (0 1818 | ((cke_rst & 0x3) << 28) 1819 | ((cksre & 0xf) << 24) 1820 | ((cksrx & 0xf) << 20) 1821 | ((par_lat & 0xf) << 16) 1822 | ((cs_to_cmd & 0xf) << 4) 1823 ); 1824 debug("FSLDDR: timing_cfg_7 = 0x%08x\n", ddr->timing_cfg_7); 1825 } 1826 1827 static void set_timing_cfg_8(fsl_ddr_cfg_regs_t *ddr, 1828 const memctl_options_t *popts, 1829 const common_timing_params_t *common_dimm, 1830 unsigned int cas_latency) 1831 { 1832 unsigned int rwt_bg, wrt_bg, rrt_bg, wwt_bg; 1833 unsigned int acttoact_bg, wrtord_bg, pre_all_rec; 1834 unsigned int tccdl = picos_to_mclk(common_dimm->tccdl_ps); 1835 unsigned int wr_lat = ((ddr->timing_cfg_2 & 0x00780000) >> 19) + 1836 ((ddr->timing_cfg_2 & 0x00040000) >> 14); 1837 1838 rwt_bg = cas_latency + 2 + 4 - wr_lat; 1839 if (rwt_bg < tccdl) 1840 rwt_bg = tccdl - rwt_bg; 1841 else 1842 rwt_bg = 0; 1843 1844 wrt_bg = wr_lat + 4 + 1 - cas_latency; 1845 if (wrt_bg < tccdl) 1846 wrt_bg = tccdl - wrt_bg; 1847 else 1848 wrt_bg = 0; 1849 1850 if (popts->burst_length == DDR_BL8) { 1851 rrt_bg = tccdl - 4; 1852 wwt_bg = tccdl - 4; 1853 } else { 1854 rrt_bg = tccdl - 2; 1855 wwt_bg = tccdl - 4; 1856 } 1857 1858 acttoact_bg = picos_to_mclk(common_dimm->trrdl_ps); 1859 wrtord_bg = max(4, picos_to_mclk(7500)); 1860 if (popts->otf_burst_chop_en) 1861 wrtord_bg += 2; 1862 1863 pre_all_rec = 0; 1864 1865 ddr->timing_cfg_8 = (0 1866 | ((rwt_bg & 0xf) << 28) 1867 | ((wrt_bg & 0xf) << 24) 1868 | ((rrt_bg & 0xf) << 20) 1869 | ((wwt_bg & 0xf) << 16) 1870 | ((acttoact_bg & 0xf) << 12) 1871 | ((wrtord_bg & 0xf) << 8) 1872 | ((pre_all_rec & 0x1f) << 0) 1873 ); 1874 1875 debug("FSLDDR: timing_cfg_8 = 0x%08x\n", ddr->timing_cfg_8); 1876 } 1877 1878 static void set_timing_cfg_9(fsl_ddr_cfg_regs_t *ddr) 1879 { 1880 ddr->timing_cfg_9 = 0; 1881 debug("FSLDDR: timing_cfg_9 = 0x%08x\n", ddr->timing_cfg_9); 1882 } 1883 1884 static void set_ddr_dq_mapping(fsl_ddr_cfg_regs_t *ddr, 1885 const dimm_params_t *dimm_params) 1886 { 1887 ddr->dq_map_0 = ((dimm_params->dq_mapping[0] & 0x3F) << 26) | 1888 ((dimm_params->dq_mapping[1] & 0x3F) << 20) | 1889 ((dimm_params->dq_mapping[2] & 0x3F) << 14) | 1890 ((dimm_params->dq_mapping[3] & 0x3F) << 8) | 1891 ((dimm_params->dq_mapping[4] & 0x3F) << 2); 1892 1893 ddr->dq_map_1 = ((dimm_params->dq_mapping[5] & 0x3F) << 26) | 1894 ((dimm_params->dq_mapping[6] & 0x3F) << 20) | 1895 ((dimm_params->dq_mapping[7] & 0x3F) << 14) | 1896 ((dimm_params->dq_mapping[10] & 0x3F) << 8) | 1897 ((dimm_params->dq_mapping[11] & 0x3F) << 2); 1898 1899 ddr->dq_map_2 = ((dimm_params->dq_mapping[12] & 0x3F) << 26) | 1900 ((dimm_params->dq_mapping[13] & 0x3F) << 20) | 1901 ((dimm_params->dq_mapping[14] & 0x3F) << 14) | 1902 ((dimm_params->dq_mapping[15] & 0x3F) << 8) | 1903 ((dimm_params->dq_mapping[16] & 0x3F) << 2); 1904 1905 ddr->dq_map_3 = ((dimm_params->dq_mapping[17] & 0x3F) << 26) | 1906 ((dimm_params->dq_mapping[8] & 0x3F) << 20) | 1907 ((dimm_params->dq_mapping[9] & 0x3F) << 14) | 1908 dimm_params->dq_mapping_ors; 1909 1910 debug("FSLDDR: dq_map_0 = 0x%08x\n", ddr->dq_map_0); 1911 debug("FSLDDR: dq_map_1 = 0x%08x\n", ddr->dq_map_1); 1912 debug("FSLDDR: dq_map_2 = 0x%08x\n", ddr->dq_map_2); 1913 debug("FSLDDR: dq_map_3 = 0x%08x\n", ddr->dq_map_3); 1914 } 1915 static void set_ddr_sdram_cfg_3(fsl_ddr_cfg_regs_t *ddr, 1916 const memctl_options_t *popts) 1917 { 1918 int rd_pre; 1919 1920 rd_pre = popts->quad_rank_present ? 1 : 0; 1921 1922 ddr->ddr_sdram_cfg_3 = (rd_pre & 0x1) << 16; 1923 1924 debug("FSLDDR: ddr_sdram_cfg_3 = 0x%08x\n", ddr->ddr_sdram_cfg_3); 1925 } 1926 #endif /* CONFIG_SYS_FSL_DDR4 */ 1927 1928 /* DDR ZQ Calibration Control (DDR_ZQ_CNTL) */ 1929 static void set_ddr_zq_cntl(fsl_ddr_cfg_regs_t *ddr, unsigned int zq_en) 1930 { 1931 unsigned int zqinit = 0;/* POR ZQ Calibration Time (tZQinit) */ 1932 /* Normal Operation Full Calibration Time (tZQoper) */ 1933 unsigned int zqoper = 0; 1934 /* Normal Operation Short Calibration Time (tZQCS) */ 1935 unsigned int zqcs = 0; 1936 #ifdef CONFIG_SYS_FSL_DDR4 1937 unsigned int zqcs_init; 1938 #endif 1939 1940 if (zq_en) { 1941 #ifdef CONFIG_SYS_FSL_DDR4 1942 zqinit = 10; /* 1024 clocks */ 1943 zqoper = 9; /* 512 clocks */ 1944 zqcs = 7; /* 128 clocks */ 1945 zqcs_init = 5; /* 1024 refresh sequences */ 1946 #else 1947 zqinit = 9; /* 512 clocks */ 1948 zqoper = 8; /* 256 clocks */ 1949 zqcs = 6; /* 64 clocks */ 1950 #endif 1951 } 1952 1953 ddr->ddr_zq_cntl = (0 1954 | ((zq_en & 0x1) << 31) 1955 | ((zqinit & 0xF) << 24) 1956 | ((zqoper & 0xF) << 16) 1957 | ((zqcs & 0xF) << 8) 1958 #ifdef CONFIG_SYS_FSL_DDR4 1959 | ((zqcs_init & 0xF) << 0) 1960 #endif 1961 ); 1962 debug("FSLDDR: zq_cntl = 0x%08x\n", ddr->ddr_zq_cntl); 1963 } 1964 1965 /* DDR Write Leveling Control (DDR_WRLVL_CNTL) */ 1966 static void set_ddr_wrlvl_cntl(fsl_ddr_cfg_regs_t *ddr, unsigned int wrlvl_en, 1967 const memctl_options_t *popts) 1968 { 1969 /* 1970 * First DQS pulse rising edge after margining mode 1971 * is programmed (tWL_MRD) 1972 */ 1973 unsigned int wrlvl_mrd = 0; 1974 /* ODT delay after margining mode is programmed (tWL_ODTEN) */ 1975 unsigned int wrlvl_odten = 0; 1976 /* DQS/DQS_ delay after margining mode is programmed (tWL_DQSEN) */ 1977 unsigned int wrlvl_dqsen = 0; 1978 /* WRLVL_SMPL: Write leveling sample time */ 1979 unsigned int wrlvl_smpl = 0; 1980 /* WRLVL_WLR: Write leveling repeition time */ 1981 unsigned int wrlvl_wlr = 0; 1982 /* WRLVL_START: Write leveling start time */ 1983 unsigned int wrlvl_start = 0; 1984 1985 /* suggest enable write leveling for DDR3 due to fly-by topology */ 1986 if (wrlvl_en) { 1987 /* tWL_MRD min = 40 nCK, we set it 64 */ 1988 wrlvl_mrd = 0x6; 1989 /* tWL_ODTEN 128 */ 1990 wrlvl_odten = 0x7; 1991 /* tWL_DQSEN min = 25 nCK, we set it 32 */ 1992 wrlvl_dqsen = 0x5; 1993 /* 1994 * Write leveling sample time at least need 6 clocks 1995 * higher than tWLO to allow enough time for progagation 1996 * delay and sampling the prime data bits. 1997 */ 1998 wrlvl_smpl = 0xf; 1999 /* 2000 * Write leveling repetition time 2001 * at least tWLO + 6 clocks clocks 2002 * we set it 64 2003 */ 2004 wrlvl_wlr = 0x6; 2005 /* 2006 * Write leveling start time 2007 * The value use for the DQS_ADJUST for the first sample 2008 * when write leveling is enabled. It probably needs to be 2009 * overriden per platform. 2010 */ 2011 wrlvl_start = 0x8; 2012 /* 2013 * Override the write leveling sample and start time 2014 * according to specific board 2015 */ 2016 if (popts->wrlvl_override) { 2017 wrlvl_smpl = popts->wrlvl_sample; 2018 wrlvl_start = popts->wrlvl_start; 2019 } 2020 } 2021 2022 ddr->ddr_wrlvl_cntl = (0 2023 | ((wrlvl_en & 0x1) << 31) 2024 | ((wrlvl_mrd & 0x7) << 24) 2025 | ((wrlvl_odten & 0x7) << 20) 2026 | ((wrlvl_dqsen & 0x7) << 16) 2027 | ((wrlvl_smpl & 0xf) << 12) 2028 | ((wrlvl_wlr & 0x7) << 8) 2029 | ((wrlvl_start & 0x1F) << 0) 2030 ); 2031 debug("FSLDDR: wrlvl_cntl = 0x%08x\n", ddr->ddr_wrlvl_cntl); 2032 ddr->ddr_wrlvl_cntl_2 = popts->wrlvl_ctl_2; 2033 debug("FSLDDR: wrlvl_cntl_2 = 0x%08x\n", ddr->ddr_wrlvl_cntl_2); 2034 ddr->ddr_wrlvl_cntl_3 = popts->wrlvl_ctl_3; 2035 debug("FSLDDR: wrlvl_cntl_3 = 0x%08x\n", ddr->ddr_wrlvl_cntl_3); 2036 2037 } 2038 2039 /* DDR Self Refresh Counter (DDR_SR_CNTR) */ 2040 static void set_ddr_sr_cntr(fsl_ddr_cfg_regs_t *ddr, unsigned int sr_it) 2041 { 2042 /* Self Refresh Idle Threshold */ 2043 ddr->ddr_sr_cntr = (sr_it & 0xF) << 16; 2044 } 2045 2046 static void set_ddr_eor(fsl_ddr_cfg_regs_t *ddr, const memctl_options_t *popts) 2047 { 2048 if (popts->addr_hash) { 2049 ddr->ddr_eor = 0x40000000; /* address hash enable */ 2050 puts("Address hashing enabled.\n"); 2051 } 2052 } 2053 2054 static void set_ddr_cdr1(fsl_ddr_cfg_regs_t *ddr, const memctl_options_t *popts) 2055 { 2056 ddr->ddr_cdr1 = popts->ddr_cdr1; 2057 debug("FSLDDR: ddr_cdr1 = 0x%08x\n", ddr->ddr_cdr1); 2058 } 2059 2060 static void set_ddr_cdr2(fsl_ddr_cfg_regs_t *ddr, const memctl_options_t *popts) 2061 { 2062 ddr->ddr_cdr2 = popts->ddr_cdr2; 2063 debug("FSLDDR: ddr_cdr2 = 0x%08x\n", ddr->ddr_cdr2); 2064 } 2065 2066 unsigned int 2067 check_fsl_memctl_config_regs(const fsl_ddr_cfg_regs_t *ddr) 2068 { 2069 unsigned int res = 0; 2070 2071 /* 2072 * Check that DDR_SDRAM_CFG[RD_EN] and DDR_SDRAM_CFG[2T_EN] are 2073 * not set at the same time. 2074 */ 2075 if (ddr->ddr_sdram_cfg & 0x10000000 2076 && ddr->ddr_sdram_cfg & 0x00008000) { 2077 printf("Error: DDR_SDRAM_CFG[RD_EN] and DDR_SDRAM_CFG[2T_EN] " 2078 " should not be set at the same time.\n"); 2079 res++; 2080 } 2081 2082 return res; 2083 } 2084 2085 unsigned int 2086 compute_fsl_memctl_config_regs(const memctl_options_t *popts, 2087 fsl_ddr_cfg_regs_t *ddr, 2088 const common_timing_params_t *common_dimm, 2089 const dimm_params_t *dimm_params, 2090 unsigned int dbw_cap_adj, 2091 unsigned int size_only) 2092 { 2093 unsigned int i; 2094 unsigned int cas_latency; 2095 unsigned int additive_latency; 2096 unsigned int sr_it; 2097 unsigned int zq_en; 2098 unsigned int wrlvl_en; 2099 unsigned int ip_rev = 0; 2100 unsigned int unq_mrs_en = 0; 2101 int cs_en = 1; 2102 2103 memset(ddr, 0, sizeof(fsl_ddr_cfg_regs_t)); 2104 2105 if (common_dimm == NULL) { 2106 printf("Error: subset DIMM params struct null pointer\n"); 2107 return 1; 2108 } 2109 2110 /* 2111 * Process overrides first. 2112 * 2113 * FIXME: somehow add dereated caslat to this 2114 */ 2115 cas_latency = (popts->cas_latency_override) 2116 ? popts->cas_latency_override_value 2117 : common_dimm->lowest_common_spd_caslat; 2118 2119 additive_latency = (popts->additive_latency_override) 2120 ? popts->additive_latency_override_value 2121 : common_dimm->additive_latency; 2122 2123 sr_it = (popts->auto_self_refresh_en) 2124 ? popts->sr_it 2125 : 0; 2126 /* ZQ calibration */ 2127 zq_en = (popts->zq_en) ? 1 : 0; 2128 /* write leveling */ 2129 wrlvl_en = (popts->wrlvl_en) ? 1 : 0; 2130 2131 /* Chip Select Memory Bounds (CSn_BNDS) */ 2132 for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) { 2133 unsigned long long ea, sa; 2134 unsigned int cs_per_dimm 2135 = CONFIG_CHIP_SELECTS_PER_CTRL / CONFIG_DIMM_SLOTS_PER_CTLR; 2136 unsigned int dimm_number 2137 = i / cs_per_dimm; 2138 unsigned long long rank_density 2139 = dimm_params[dimm_number].rank_density >> dbw_cap_adj; 2140 2141 if (dimm_params[dimm_number].n_ranks == 0) { 2142 debug("Skipping setup of CS%u " 2143 "because n_ranks on DIMM %u is 0\n", i, dimm_number); 2144 continue; 2145 } 2146 if (popts->memctl_interleaving) { 2147 switch (popts->ba_intlv_ctl & FSL_DDR_CS0_CS1_CS2_CS3) { 2148 case FSL_DDR_CS0_CS1_CS2_CS3: 2149 break; 2150 case FSL_DDR_CS0_CS1: 2151 case FSL_DDR_CS0_CS1_AND_CS2_CS3: 2152 if (i > 1) 2153 cs_en = 0; 2154 break; 2155 case FSL_DDR_CS2_CS3: 2156 default: 2157 if (i > 0) 2158 cs_en = 0; 2159 break; 2160 } 2161 sa = common_dimm->base_address; 2162 ea = sa + common_dimm->total_mem - 1; 2163 } else if (!popts->memctl_interleaving) { 2164 /* 2165 * If memory interleaving between controllers is NOT 2166 * enabled, the starting address for each memory 2167 * controller is distinct. However, because rank 2168 * interleaving is enabled, the starting and ending 2169 * addresses of the total memory on that memory 2170 * controller needs to be programmed into its 2171 * respective CS0_BNDS. 2172 */ 2173 switch (popts->ba_intlv_ctl & FSL_DDR_CS0_CS1_CS2_CS3) { 2174 case FSL_DDR_CS0_CS1_CS2_CS3: 2175 sa = common_dimm->base_address; 2176 ea = sa + common_dimm->total_mem - 1; 2177 break; 2178 case FSL_DDR_CS0_CS1_AND_CS2_CS3: 2179 if ((i >= 2) && (dimm_number == 0)) { 2180 sa = dimm_params[dimm_number].base_address + 2181 2 * rank_density; 2182 ea = sa + 2 * rank_density - 1; 2183 } else { 2184 sa = dimm_params[dimm_number].base_address; 2185 ea = sa + 2 * rank_density - 1; 2186 } 2187 break; 2188 case FSL_DDR_CS0_CS1: 2189 if (dimm_params[dimm_number].n_ranks > (i % cs_per_dimm)) { 2190 sa = dimm_params[dimm_number].base_address; 2191 ea = sa + rank_density - 1; 2192 if (i != 1) 2193 sa += (i % cs_per_dimm) * rank_density; 2194 ea += (i % cs_per_dimm) * rank_density; 2195 } else { 2196 sa = 0; 2197 ea = 0; 2198 } 2199 if (i == 0) 2200 ea += rank_density; 2201 break; 2202 case FSL_DDR_CS2_CS3: 2203 if (dimm_params[dimm_number].n_ranks > (i % cs_per_dimm)) { 2204 sa = dimm_params[dimm_number].base_address; 2205 ea = sa + rank_density - 1; 2206 if (i != 3) 2207 sa += (i % cs_per_dimm) * rank_density; 2208 ea += (i % cs_per_dimm) * rank_density; 2209 } else { 2210 sa = 0; 2211 ea = 0; 2212 } 2213 if (i == 2) 2214 ea += (rank_density >> dbw_cap_adj); 2215 break; 2216 default: /* No bank(chip-select) interleaving */ 2217 sa = dimm_params[dimm_number].base_address; 2218 ea = sa + rank_density - 1; 2219 if (dimm_params[dimm_number].n_ranks > (i % cs_per_dimm)) { 2220 sa += (i % cs_per_dimm) * rank_density; 2221 ea += (i % cs_per_dimm) * rank_density; 2222 } else { 2223 sa = 0; 2224 ea = 0; 2225 } 2226 break; 2227 } 2228 } 2229 2230 sa >>= 24; 2231 ea >>= 24; 2232 2233 if (cs_en) { 2234 ddr->cs[i].bnds = (0 2235 | ((sa & 0xffff) << 16) /* starting address */ 2236 | ((ea & 0xffff) << 0) /* ending address */ 2237 ); 2238 } else { 2239 /* setting bnds to 0xffffffff for inactive CS */ 2240 ddr->cs[i].bnds = 0xffffffff; 2241 } 2242 2243 debug("FSLDDR: cs[%d]_bnds = 0x%08x\n", i, ddr->cs[i].bnds); 2244 set_csn_config(dimm_number, i, ddr, popts, dimm_params); 2245 set_csn_config_2(i, ddr); 2246 } 2247 2248 /* 2249 * In the case we only need to compute the ddr sdram size, we only need 2250 * to set csn registers, so return from here. 2251 */ 2252 if (size_only) 2253 return 0; 2254 2255 set_ddr_eor(ddr, popts); 2256 2257 #if !defined(CONFIG_SYS_FSL_DDR1) 2258 set_timing_cfg_0(ddr, popts, dimm_params); 2259 #endif 2260 2261 set_timing_cfg_3(ddr, popts, common_dimm, cas_latency, 2262 additive_latency); 2263 set_timing_cfg_1(ddr, popts, common_dimm, cas_latency); 2264 set_timing_cfg_2(ddr, popts, common_dimm, 2265 cas_latency, additive_latency); 2266 2267 set_ddr_cdr1(ddr, popts); 2268 set_ddr_cdr2(ddr, popts); 2269 set_ddr_sdram_cfg(ddr, popts, common_dimm); 2270 ip_rev = fsl_ddr_get_version(); 2271 if (ip_rev > 0x40400) 2272 unq_mrs_en = 1; 2273 2274 set_ddr_sdram_cfg_2(ddr, popts, unq_mrs_en); 2275 set_ddr_sdram_mode(ddr, popts, common_dimm, 2276 cas_latency, additive_latency, unq_mrs_en); 2277 set_ddr_sdram_mode_2(ddr, popts, common_dimm, unq_mrs_en); 2278 #ifdef CONFIG_SYS_FSL_DDR4 2279 set_ddr_sdram_mode_9(ddr, popts, common_dimm, unq_mrs_en); 2280 set_ddr_sdram_mode_10(ddr, popts, common_dimm, unq_mrs_en); 2281 #endif 2282 set_ddr_sdram_interval(ddr, popts, common_dimm); 2283 set_ddr_data_init(ddr); 2284 set_ddr_sdram_clk_cntl(ddr, popts); 2285 set_ddr_init_addr(ddr); 2286 set_ddr_init_ext_addr(ddr); 2287 set_timing_cfg_4(ddr, popts); 2288 set_timing_cfg_5(ddr, cas_latency); 2289 #ifdef CONFIG_SYS_FSL_DDR4 2290 set_ddr_sdram_cfg_3(ddr, popts); 2291 set_timing_cfg_6(ddr); 2292 set_timing_cfg_7(ddr, common_dimm); 2293 set_timing_cfg_8(ddr, popts, common_dimm, cas_latency); 2294 set_timing_cfg_9(ddr); 2295 set_ddr_dq_mapping(ddr, dimm_params); 2296 #endif 2297 2298 set_ddr_zq_cntl(ddr, zq_en); 2299 set_ddr_wrlvl_cntl(ddr, wrlvl_en, popts); 2300 2301 set_ddr_sr_cntr(ddr, sr_it); 2302 2303 set_ddr_sdram_rcw(ddr, popts, common_dimm); 2304 2305 #ifdef CONFIG_SYS_FSL_DDR_EMU 2306 /* disble DDR training for emulator */ 2307 ddr->debug[2] = 0x00000400; 2308 ddr->debug[4] = 0xff800000; 2309 #endif 2310 #ifdef CONFIG_SYS_FSL_ERRATUM_A004508 2311 if ((ip_rev >= 0x40000) && (ip_rev < 0x40400)) 2312 ddr->debug[2] |= 0x00000200; /* set bit 22 */ 2313 #endif 2314 2315 return check_fsl_memctl_config_regs(ddr); 2316 } 2317