1# 2# Boot count configuration 3# 4 5menuconfig BOOTCOUNT_LIMIT 6 bool "Enable support for checking boot count limit" 7 help 8 Enable checking for exceeding the boot count limit. 9 More information: http://www.denx.de/wiki/DULG/UBootBootCountLimit 10 11if BOOTCOUNT_LIMIT 12 13choice 14 prompt "Boot count device" 15 default BOOTCOUNT_AM33XX if AM33XX || SOC_DA8XX 16 default BOOTCOUNT_AT91 if AT91SAM9XE 17 default BOOTCOUNT_GENERIC 18 19config BOOTCOUNT_GENERIC 20 bool "Generic default boot counter" 21 help 22 Generic bootcount stored at SYS_BOOTCOUNT_ADDR. 23 24 SYS_BOOTCOUNT_ADDR: 25 Set to the address where the bootcount and bootcount magic 26 will be stored. 27 28config BOOTCOUNT_EXT 29 bool "Boot counter on EXT filesystem" 30 help 31 Add support for maintaining boot count in a file on an EXT 32 filesystem. 33 34config BOOTCOUNT_AM33XX 35 bool "Boot counter in AM33XX RTC IP block" 36 depends on AM33XX || SOC_DA8XX 37 select SPL_AM33XX_ENABLE_RTC32K_OSC if AM33XX 38 help 39 A bootcount driver for the RTC IP block found on many TI platforms. 40 This requires the RTC clocks, etc, to be enabled prior to use and 41 not all boards with this IP block on it will have the RTC in use. 42 43config BOOTCOUNT_ENV 44 bool "Boot counter in environment" 45 help 46 If no softreset save registers are found on the hardware 47 "bootcount" is stored in the environment. To prevent a 48 saveenv on all reboots, the environment variable 49 "upgrade_available" is used. If "upgrade_available" is 50 0, "bootcount" is always 0, if "upgrade_available" is 51 1 "bootcount" is incremented in the environment. 52 So the Userspace Application must set the "upgrade_available" 53 and "bootcount" variable to 0, if a boot was successfully. 54 55config BOOTCOUNT_RAM 56 bool "Boot counter in RAM" 57 help 58 Store the bootcount in DRAM protected against against bit errors 59 due to short power loss or holding a system in RESET. 60 61config BOOTCOUNT_I2C 62 bool "Boot counter on I2C device" 63 help 64 Enable support for the bootcounter on an i2c (like RTC) device. 65 CONFIG_SYS_I2C_RTC_ADDR = i2c chip address 66 CONFIG_SYS_BOOTCOUNT_ADDR = i2c addr which is used for 67 the bootcounter. 68 69config BOOTCOUNT_AT91 70 bool "Boot counter for Atmel AT91SAM9XE" 71 depends on AT91SAM9XE 72 73endchoice 74 75config BOOTCOUNT_BOOTLIMIT 76 int "Maximum number of reboot cycles allowed" 77 default 0 78 help 79 Set the Maximum number of reboot cycles allowed without the boot 80 counter being cleared. 81 If set to 0 do not set a boot limit in the environment. 82 83config BOOTCOUNT_ALEN 84 int "I2C address length" 85 default 1 86 depends on BOOTCOUNT_I2C 87 help 88 Length of the the I2C address at SYS_BOOTCOUNT_ADDR for storing 89 the boot counter. 90 91config SYS_BOOTCOUNT_SINGLEWORD 92 bool "Use single word to pack boot count and magic value" 93 depends on BOOTCOUNT_GENERIC 94 help 95 This option enables packing boot count magic value and boot count 96 into single word (32 bits). 97 98config SYS_BOOTCOUNT_EXT_INTERFACE 99 string "Interface on which to find boot counter EXT filesystem" 100 default "mmc" 101 depends on BOOTCOUNT_EXT 102 help 103 Set the interface to use when locating the filesystem to use for the 104 boot counter. 105 106config SYS_BOOTCOUNT_EXT_DEVPART 107 string "Partition of the boot counter EXT filesystem" 108 default "0:1" 109 depends on BOOTCOUNT_EXT 110 help 111 Set the partition to use when locating the filesystem to use for the 112 boot counter. 113 114config SYS_BOOTCOUNT_EXT_NAME 115 string "Path and filename of the EXT filesystem based boot counter" 116 default "/boot/failures" 117 depends on BOOTCOUNT_EXT 118 help 119 Set the filename and path of the file used to store the boot counter. 120 121config SYS_BOOTCOUNT_ADDR 122 hex "RAM address used for reading and writing the boot counter" 123 default 0x44E3E000 if BOOTCOUNT_AM33XX 124 default 0xE0115FF8 if ARCH_LS1043A || ARCH_LS1021A 125 depends on BOOTCOUNT_AM33XX || BOOTCOUNT_GENERIC || BOOTCOUNT_EXT || \ 126 BOOTCOUNT_I2C 127 help 128 Set the address used for reading and writing the boot counter. 129 130config SYS_BOOTCOUNT_MAGIC 131 hex "Magic value for the boot counter" 132 default 0xB001C041 133 help 134 Set the magic value used for the boot counter. 135 136endif 137