1 // SPDX-License-Identifier: GPL-2.0+ 2 /* 3 * (C) Copyright 2000-2011 4 * Wolfgang Denk, DENX Software Engineering, wd@denx.de. 5 */ 6 7 #include <common.h> 8 #include <ata.h> 9 #include <dm.h> 10 #include <ide.h> 11 #include <watchdog.h> 12 #include <asm/io.h> 13 14 #ifdef __PPC__ 15 # define EIEIO __asm__ volatile ("eieio") 16 # define SYNC __asm__ volatile ("sync") 17 #else 18 # define EIEIO /* nothing */ 19 # define SYNC /* nothing */ 20 #endif 21 22 /* Current offset for IDE0 / IDE1 bus access */ 23 ulong ide_bus_offset[CONFIG_SYS_IDE_MAXBUS] = { 24 #if defined(CONFIG_SYS_ATA_IDE0_OFFSET) 25 CONFIG_SYS_ATA_IDE0_OFFSET, 26 #endif 27 #if defined(CONFIG_SYS_ATA_IDE1_OFFSET) && (CONFIG_SYS_IDE_MAXBUS > 1) 28 CONFIG_SYS_ATA_IDE1_OFFSET, 29 #endif 30 }; 31 32 static int ide_bus_ok[CONFIG_SYS_IDE_MAXBUS]; 33 34 struct blk_desc ide_dev_desc[CONFIG_SYS_IDE_MAXDEVICE]; 35 36 #define IDE_TIME_OUT 2000 /* 2 sec timeout */ 37 38 #define ATAPI_TIME_OUT 7000 /* 7 sec timeout (5 sec seems to work...) */ 39 40 #define IDE_SPIN_UP_TIME_OUT 5000 /* 5 sec spin-up timeout */ 41 42 #ifndef CONFIG_SYS_ATA_PORT_ADDR 43 #define CONFIG_SYS_ATA_PORT_ADDR(port) (port) 44 #endif 45 46 #ifdef CONFIG_IDE_RESET 47 extern void ide_set_reset(int idereset); 48 49 static void ide_reset(void) 50 { 51 int i; 52 53 for (i = 0; i < CONFIG_SYS_IDE_MAXBUS; ++i) 54 ide_bus_ok[i] = 0; 55 for (i = 0; i < CONFIG_SYS_IDE_MAXDEVICE; ++i) 56 ide_dev_desc[i].type = DEV_TYPE_UNKNOWN; 57 58 ide_set_reset(1); /* assert reset */ 59 60 /* the reset signal shall be asserted for et least 25 us */ 61 udelay(25); 62 63 WATCHDOG_RESET(); 64 65 /* de-assert RESET signal */ 66 ide_set_reset(0); 67 68 /* wait 250 ms */ 69 for (i = 0; i < 250; ++i) 70 udelay(1000); 71 } 72 #else 73 #define ide_reset() /* dummy */ 74 #endif /* CONFIG_IDE_RESET */ 75 76 /* 77 * Wait until Busy bit is off, or timeout (in ms) 78 * Return last status 79 */ 80 static uchar ide_wait(int dev, ulong t) 81 { 82 ulong delay = 10 * t; /* poll every 100 us */ 83 uchar c; 84 85 while ((c = ide_inb(dev, ATA_STATUS)) & ATA_STAT_BUSY) { 86 udelay(100); 87 if (delay-- == 0) 88 break; 89 } 90 return c; 91 } 92 93 /* 94 * copy src to dest, skipping leading and trailing blanks and null 95 * terminate the string 96 * "len" is the size of available memory including the terminating '\0' 97 */ 98 static void ident_cpy(unsigned char *dst, unsigned char *src, 99 unsigned int len) 100 { 101 unsigned char *end, *last; 102 103 last = dst; 104 end = src + len - 1; 105 106 /* reserve space for '\0' */ 107 if (len < 2) 108 goto OUT; 109 110 /* skip leading white space */ 111 while ((*src) && (src < end) && (*src == ' ')) 112 ++src; 113 114 /* copy string, omitting trailing white space */ 115 while ((*src) && (src < end)) { 116 *dst++ = *src; 117 if (*src++ != ' ') 118 last = dst; 119 } 120 OUT: 121 *last = '\0'; 122 } 123 124 #ifdef CONFIG_ATAPI 125 /**************************************************************************** 126 * ATAPI Support 127 */ 128 129 #if defined(CONFIG_IDE_SWAP_IO) 130 /* since ATAPI may use commands with not 4 bytes alligned length 131 * we have our own transfer functions, 2 bytes alligned */ 132 __weak void ide_output_data_shorts(int dev, ushort *sect_buf, int shorts) 133 { 134 ushort *dbuf; 135 volatile ushort *pbuf; 136 137 pbuf = (ushort *)(ATA_CURR_BASE(dev) + ATA_DATA_REG); 138 dbuf = (ushort *)sect_buf; 139 140 debug("in output data shorts base for read is %lx\n", 141 (unsigned long) pbuf); 142 143 while (shorts--) { 144 EIEIO; 145 *pbuf = *dbuf++; 146 } 147 } 148 149 __weak void ide_input_data_shorts(int dev, ushort *sect_buf, int shorts) 150 { 151 ushort *dbuf; 152 volatile ushort *pbuf; 153 154 pbuf = (ushort *)(ATA_CURR_BASE(dev) + ATA_DATA_REG); 155 dbuf = (ushort *)sect_buf; 156 157 debug("in input data shorts base for read is %lx\n", 158 (unsigned long) pbuf); 159 160 while (shorts--) { 161 EIEIO; 162 *dbuf++ = *pbuf; 163 } 164 } 165 166 #else /* ! CONFIG_IDE_SWAP_IO */ 167 __weak void ide_output_data_shorts(int dev, ushort *sect_buf, int shorts) 168 { 169 outsw(ATA_CURR_BASE(dev) + ATA_DATA_REG, sect_buf, shorts); 170 } 171 172 __weak void ide_input_data_shorts(int dev, ushort *sect_buf, int shorts) 173 { 174 insw(ATA_CURR_BASE(dev) + ATA_DATA_REG, sect_buf, shorts); 175 } 176 177 #endif /* CONFIG_IDE_SWAP_IO */ 178 179 /* 180 * Wait until (Status & mask) == res, or timeout (in ms) 181 * Return last status 182 * This is used since some ATAPI CD ROMs clears their Busy Bit first 183 * and then they set their DRQ Bit 184 */ 185 static uchar atapi_wait_mask(int dev, ulong t, uchar mask, uchar res) 186 { 187 ulong delay = 10 * t; /* poll every 100 us */ 188 uchar c; 189 190 /* prevents to read the status before valid */ 191 c = ide_inb(dev, ATA_DEV_CTL); 192 193 while (((c = ide_inb(dev, ATA_STATUS)) & mask) != res) { 194 /* break if error occurs (doesn't make sense to wait more) */ 195 if ((c & ATA_STAT_ERR) == ATA_STAT_ERR) 196 break; 197 udelay(100); 198 if (delay-- == 0) 199 break; 200 } 201 return c; 202 } 203 204 /* 205 * issue an atapi command 206 */ 207 unsigned char atapi_issue(int device, unsigned char *ccb, int ccblen, 208 unsigned char *buffer, int buflen) 209 { 210 unsigned char c, err, mask, res; 211 int n; 212 213 /* Select device 214 */ 215 mask = ATA_STAT_BUSY | ATA_STAT_DRQ; 216 res = 0; 217 ide_outb(device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device)); 218 c = atapi_wait_mask(device, ATAPI_TIME_OUT, mask, res); 219 if ((c & mask) != res) { 220 printf("ATAPI_ISSUE: device %d not ready status %X\n", device, 221 c); 222 err = 0xFF; 223 goto AI_OUT; 224 } 225 /* write taskfile */ 226 ide_outb(device, ATA_ERROR_REG, 0); /* no DMA, no overlaped */ 227 ide_outb(device, ATA_SECT_CNT, 0); 228 ide_outb(device, ATA_SECT_NUM, 0); 229 ide_outb(device, ATA_CYL_LOW, (unsigned char) (buflen & 0xFF)); 230 ide_outb(device, ATA_CYL_HIGH, 231 (unsigned char) ((buflen >> 8) & 0xFF)); 232 ide_outb(device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device)); 233 234 ide_outb(device, ATA_COMMAND, ATAPI_CMD_PACKET); 235 udelay(50); 236 237 mask = ATA_STAT_DRQ | ATA_STAT_BUSY | ATA_STAT_ERR; 238 res = ATA_STAT_DRQ; 239 c = atapi_wait_mask(device, ATAPI_TIME_OUT, mask, res); 240 241 if ((c & mask) != res) { /* DRQ must be 1, BSY 0 */ 242 printf("ATAPI_ISSUE: Error (no IRQ) before sending ccb dev %d status 0x%02x\n", 243 device, c); 244 err = 0xFF; 245 goto AI_OUT; 246 } 247 248 /* write command block */ 249 ide_output_data_shorts(device, (unsigned short *)ccb, ccblen / 2); 250 251 /* ATAPI Command written wait for completition */ 252 udelay(5000); /* device must set bsy */ 253 254 mask = ATA_STAT_DRQ | ATA_STAT_BUSY | ATA_STAT_ERR; 255 /* 256 * if no data wait for DRQ = 0 BSY = 0 257 * if data wait for DRQ = 1 BSY = 0 258 */ 259 res = 0; 260 if (buflen) 261 res = ATA_STAT_DRQ; 262 c = atapi_wait_mask(device, ATAPI_TIME_OUT, mask, res); 263 if ((c & mask) != res) { 264 if (c & ATA_STAT_ERR) { 265 err = (ide_inb(device, ATA_ERROR_REG)) >> 4; 266 debug("atapi_issue 1 returned sense key %X status %02X\n", 267 err, c); 268 } else { 269 printf("ATAPI_ISSUE: (no DRQ) after sending ccb (%x) status 0x%02x\n", 270 ccb[0], c); 271 err = 0xFF; 272 } 273 goto AI_OUT; 274 } 275 n = ide_inb(device, ATA_CYL_HIGH); 276 n <<= 8; 277 n += ide_inb(device, ATA_CYL_LOW); 278 if (n > buflen) { 279 printf("ERROR, transfer bytes %d requested only %d\n", n, 280 buflen); 281 err = 0xff; 282 goto AI_OUT; 283 } 284 if ((n == 0) && (buflen < 0)) { 285 printf("ERROR, transfer bytes %d requested %d\n", n, buflen); 286 err = 0xff; 287 goto AI_OUT; 288 } 289 if (n != buflen) { 290 debug("WARNING, transfer bytes %d not equal with requested %d\n", 291 n, buflen); 292 } 293 if (n != 0) { /* data transfer */ 294 debug("ATAPI_ISSUE: %d Bytes to transfer\n", n); 295 /* we transfer shorts */ 296 n >>= 1; 297 /* ok now decide if it is an in or output */ 298 if ((ide_inb(device, ATA_SECT_CNT) & 0x02) == 0) { 299 debug("Write to device\n"); 300 ide_output_data_shorts(device, (unsigned short *)buffer, 301 n); 302 } else { 303 debug("Read from device @ %p shorts %d\n", buffer, n); 304 ide_input_data_shorts(device, (unsigned short *)buffer, 305 n); 306 } 307 } 308 udelay(5000); /* seems that some CD ROMs need this... */ 309 mask = ATA_STAT_BUSY | ATA_STAT_ERR; 310 res = 0; 311 c = atapi_wait_mask(device, ATAPI_TIME_OUT, mask, res); 312 if ((c & ATA_STAT_ERR) == ATA_STAT_ERR) { 313 err = (ide_inb(device, ATA_ERROR_REG) >> 4); 314 debug("atapi_issue 2 returned sense key %X status %X\n", err, 315 c); 316 } else { 317 err = 0; 318 } 319 AI_OUT: 320 return err; 321 } 322 323 /* 324 * sending the command to atapi_issue. If an status other than good 325 * returns, an request_sense will be issued 326 */ 327 328 #define ATAPI_DRIVE_NOT_READY 100 329 #define ATAPI_UNIT_ATTN 10 330 331 unsigned char atapi_issue_autoreq(int device, 332 unsigned char *ccb, 333 int ccblen, 334 unsigned char *buffer, int buflen) 335 { 336 unsigned char sense_data[18], sense_ccb[12]; 337 unsigned char res, key, asc, ascq; 338 int notready, unitattn; 339 340 unitattn = ATAPI_UNIT_ATTN; 341 notready = ATAPI_DRIVE_NOT_READY; 342 343 retry: 344 res = atapi_issue(device, ccb, ccblen, buffer, buflen); 345 if (res == 0) 346 return 0; /* Ok */ 347 348 if (res == 0xFF) 349 return 0xFF; /* error */ 350 351 debug("(auto_req)atapi_issue returned sense key %X\n", res); 352 353 memset(sense_ccb, 0, sizeof(sense_ccb)); 354 memset(sense_data, 0, sizeof(sense_data)); 355 sense_ccb[0] = ATAPI_CMD_REQ_SENSE; 356 sense_ccb[4] = 18; /* allocation Length */ 357 358 res = atapi_issue(device, sense_ccb, 12, sense_data, 18); 359 key = (sense_data[2] & 0xF); 360 asc = (sense_data[12]); 361 ascq = (sense_data[13]); 362 363 debug("ATAPI_CMD_REQ_SENSE returned %x\n", res); 364 debug(" Sense page: %02X key %02X ASC %02X ASCQ %02X\n", 365 sense_data[0], key, asc, ascq); 366 367 if ((key == 0)) 368 return 0; /* ok device ready */ 369 370 if ((key == 6) || (asc == 0x29) || (asc == 0x28)) { /* Unit Attention */ 371 if (unitattn-- > 0) { 372 udelay(200 * 1000); 373 goto retry; 374 } 375 printf("Unit Attention, tried %d\n", ATAPI_UNIT_ATTN); 376 goto error; 377 } 378 if ((asc == 0x4) && (ascq == 0x1)) { 379 /* not ready, but will be ready soon */ 380 if (notready-- > 0) { 381 udelay(200 * 1000); 382 goto retry; 383 } 384 printf("Drive not ready, tried %d times\n", 385 ATAPI_DRIVE_NOT_READY); 386 goto error; 387 } 388 if (asc == 0x3a) { 389 debug("Media not present\n"); 390 goto error; 391 } 392 393 printf("ERROR: Unknown Sense key %02X ASC %02X ASCQ %02X\n", key, asc, 394 ascq); 395 error: 396 debug("ERROR Sense key %02X ASC %02X ASCQ %02X\n", key, asc, ascq); 397 return 0xFF; 398 } 399 400 /* 401 * atapi_read: 402 * we transfer only one block per command, since the multiple DRQ per 403 * command is not yet implemented 404 */ 405 #define ATAPI_READ_MAX_BYTES 2048 /* we read max 2kbytes */ 406 #define ATAPI_READ_BLOCK_SIZE 2048 /* assuming CD part */ 407 #define ATAPI_READ_MAX_BLOCK (ATAPI_READ_MAX_BYTES/ATAPI_READ_BLOCK_SIZE) 408 409 ulong atapi_read(struct blk_desc *block_dev, lbaint_t blknr, lbaint_t blkcnt, 410 void *buffer) 411 { 412 int device = block_dev->devnum; 413 ulong n = 0; 414 unsigned char ccb[12]; /* Command descriptor block */ 415 ulong cnt; 416 417 debug("atapi_read dev %d start " LBAF " blocks " LBAF 418 " buffer at %lX\n", device, blknr, blkcnt, (ulong) buffer); 419 420 do { 421 if (blkcnt > ATAPI_READ_MAX_BLOCK) 422 cnt = ATAPI_READ_MAX_BLOCK; 423 else 424 cnt = blkcnt; 425 426 ccb[0] = ATAPI_CMD_READ_12; 427 ccb[1] = 0; /* reserved */ 428 ccb[2] = (unsigned char) (blknr >> 24) & 0xFF; /* MSB Block */ 429 ccb[3] = (unsigned char) (blknr >> 16) & 0xFF; /* */ 430 ccb[4] = (unsigned char) (blknr >> 8) & 0xFF; 431 ccb[5] = (unsigned char) blknr & 0xFF; /* LSB Block */ 432 ccb[6] = (unsigned char) (cnt >> 24) & 0xFF; /* MSB Block cnt */ 433 ccb[7] = (unsigned char) (cnt >> 16) & 0xFF; 434 ccb[8] = (unsigned char) (cnt >> 8) & 0xFF; 435 ccb[9] = (unsigned char) cnt & 0xFF; /* LSB Block */ 436 ccb[10] = 0; /* reserved */ 437 ccb[11] = 0; /* reserved */ 438 439 if (atapi_issue_autoreq(device, ccb, 12, 440 (unsigned char *)buffer, 441 cnt * ATAPI_READ_BLOCK_SIZE) 442 == 0xFF) { 443 return n; 444 } 445 n += cnt; 446 blkcnt -= cnt; 447 blknr += cnt; 448 buffer += (cnt * ATAPI_READ_BLOCK_SIZE); 449 } while (blkcnt > 0); 450 return n; 451 } 452 453 static void atapi_inquiry(struct blk_desc *dev_desc) 454 { 455 unsigned char ccb[12]; /* Command descriptor block */ 456 unsigned char iobuf[64]; /* temp buf */ 457 unsigned char c; 458 int device; 459 460 device = dev_desc->devnum; 461 dev_desc->type = DEV_TYPE_UNKNOWN; /* not yet valid */ 462 #ifndef CONFIG_BLK 463 dev_desc->block_read = atapi_read; 464 #endif 465 466 memset(ccb, 0, sizeof(ccb)); 467 memset(iobuf, 0, sizeof(iobuf)); 468 469 ccb[0] = ATAPI_CMD_INQUIRY; 470 ccb[4] = 40; /* allocation Legnth */ 471 c = atapi_issue_autoreq(device, ccb, 12, (unsigned char *)iobuf, 40); 472 473 debug("ATAPI_CMD_INQUIRY returned %x\n", c); 474 if (c != 0) 475 return; 476 477 /* copy device ident strings */ 478 ident_cpy((unsigned char *)dev_desc->vendor, &iobuf[8], 8); 479 ident_cpy((unsigned char *)dev_desc->product, &iobuf[16], 16); 480 ident_cpy((unsigned char *)dev_desc->revision, &iobuf[32], 5); 481 482 dev_desc->lun = 0; 483 dev_desc->lba = 0; 484 dev_desc->blksz = 0; 485 dev_desc->log2blksz = LOG2_INVALID(typeof(dev_desc->log2blksz)); 486 dev_desc->type = iobuf[0] & 0x1f; 487 488 if ((iobuf[1] & 0x80) == 0x80) 489 dev_desc->removable = 1; 490 else 491 dev_desc->removable = 0; 492 493 memset(ccb, 0, sizeof(ccb)); 494 memset(iobuf, 0, sizeof(iobuf)); 495 ccb[0] = ATAPI_CMD_START_STOP; 496 ccb[4] = 0x03; /* start */ 497 498 c = atapi_issue_autoreq(device, ccb, 12, (unsigned char *)iobuf, 0); 499 500 debug("ATAPI_CMD_START_STOP returned %x\n", c); 501 if (c != 0) 502 return; 503 504 memset(ccb, 0, sizeof(ccb)); 505 memset(iobuf, 0, sizeof(iobuf)); 506 c = atapi_issue_autoreq(device, ccb, 12, (unsigned char *)iobuf, 0); 507 508 debug("ATAPI_CMD_UNIT_TEST_READY returned %x\n", c); 509 if (c != 0) 510 return; 511 512 memset(ccb, 0, sizeof(ccb)); 513 memset(iobuf, 0, sizeof(iobuf)); 514 ccb[0] = ATAPI_CMD_READ_CAP; 515 c = atapi_issue_autoreq(device, ccb, 12, (unsigned char *)iobuf, 8); 516 debug("ATAPI_CMD_READ_CAP returned %x\n", c); 517 if (c != 0) 518 return; 519 520 debug("Read Cap: LBA %02X%02X%02X%02X blksize %02X%02X%02X%02X\n", 521 iobuf[0], iobuf[1], iobuf[2], iobuf[3], 522 iobuf[4], iobuf[5], iobuf[6], iobuf[7]); 523 524 dev_desc->lba = ((unsigned long) iobuf[0] << 24) + 525 ((unsigned long) iobuf[1] << 16) + 526 ((unsigned long) iobuf[2] << 8) + ((unsigned long) iobuf[3]); 527 dev_desc->blksz = ((unsigned long) iobuf[4] << 24) + 528 ((unsigned long) iobuf[5] << 16) + 529 ((unsigned long) iobuf[6] << 8) + ((unsigned long) iobuf[7]); 530 dev_desc->log2blksz = LOG2(dev_desc->blksz); 531 #ifdef CONFIG_LBA48 532 /* ATAPI devices cannot use 48bit addressing (ATA/ATAPI v7) */ 533 dev_desc->lba48 = 0; 534 #endif 535 return; 536 } 537 538 #endif /* CONFIG_ATAPI */ 539 540 static void ide_ident(struct blk_desc *dev_desc) 541 { 542 unsigned char c; 543 hd_driveid_t iop; 544 545 #ifdef CONFIG_ATAPI 546 int retries = 0; 547 #endif 548 int device; 549 550 device = dev_desc->devnum; 551 printf(" Device %d: ", device); 552 553 /* Select device 554 */ 555 ide_outb(device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device)); 556 dev_desc->if_type = IF_TYPE_IDE; 557 #ifdef CONFIG_ATAPI 558 559 retries = 0; 560 561 /* Warning: This will be tricky to read */ 562 while (retries <= 1) { 563 /* check signature */ 564 if ((ide_inb(device, ATA_SECT_CNT) == 0x01) && 565 (ide_inb(device, ATA_SECT_NUM) == 0x01) && 566 (ide_inb(device, ATA_CYL_LOW) == 0x14) && 567 (ide_inb(device, ATA_CYL_HIGH) == 0xEB)) { 568 /* ATAPI Signature found */ 569 dev_desc->if_type = IF_TYPE_ATAPI; 570 /* 571 * Start Ident Command 572 */ 573 ide_outb(device, ATA_COMMAND, ATAPI_CMD_IDENT); 574 /* 575 * Wait for completion - ATAPI devices need more time 576 * to become ready 577 */ 578 c = ide_wait(device, ATAPI_TIME_OUT); 579 } else 580 #endif 581 { 582 /* 583 * Start Ident Command 584 */ 585 ide_outb(device, ATA_COMMAND, ATA_CMD_IDENT); 586 587 /* 588 * Wait for completion 589 */ 590 c = ide_wait(device, IDE_TIME_OUT); 591 } 592 593 if (((c & ATA_STAT_DRQ) == 0) || 594 ((c & (ATA_STAT_FAULT | ATA_STAT_ERR)) != 0)) { 595 #ifdef CONFIG_ATAPI 596 { 597 /* 598 * Need to soft reset the device 599 * in case it's an ATAPI... 600 */ 601 debug("Retrying...\n"); 602 ide_outb(device, ATA_DEV_HD, 603 ATA_LBA | ATA_DEVICE(device)); 604 udelay(100000); 605 ide_outb(device, ATA_COMMAND, 0x08); 606 udelay(500000); /* 500 ms */ 607 } 608 /* 609 * Select device 610 */ 611 ide_outb(device, ATA_DEV_HD, 612 ATA_LBA | ATA_DEVICE(device)); 613 retries++; 614 #else 615 return; 616 #endif 617 } 618 #ifdef CONFIG_ATAPI 619 else 620 break; 621 } /* see above - ugly to read */ 622 623 if (retries == 2) /* Not found */ 624 return; 625 #endif 626 627 ide_input_swap_data(device, (ulong *)&iop, ATA_SECTORWORDS); 628 629 ident_cpy((unsigned char *)dev_desc->revision, iop.fw_rev, 630 sizeof(dev_desc->revision)); 631 ident_cpy((unsigned char *)dev_desc->vendor, iop.model, 632 sizeof(dev_desc->vendor)); 633 ident_cpy((unsigned char *)dev_desc->product, iop.serial_no, 634 sizeof(dev_desc->product)); 635 #ifdef __LITTLE_ENDIAN 636 /* 637 * firmware revision, model, and serial number have Big Endian Byte 638 * order in Word. Convert all three to little endian. 639 * 640 * See CF+ and CompactFlash Specification Revision 2.0: 641 * 6.2.1.6: Identify Drive, Table 39 for more details 642 */ 643 644 strswab(dev_desc->revision); 645 strswab(dev_desc->vendor); 646 strswab(dev_desc->product); 647 #endif /* __LITTLE_ENDIAN */ 648 649 if ((iop.config & 0x0080) == 0x0080) 650 dev_desc->removable = 1; 651 else 652 dev_desc->removable = 0; 653 654 #ifdef CONFIG_ATAPI 655 if (dev_desc->if_type == IF_TYPE_ATAPI) { 656 atapi_inquiry(dev_desc); 657 return; 658 } 659 #endif /* CONFIG_ATAPI */ 660 661 #ifdef __BIG_ENDIAN 662 /* swap shorts */ 663 dev_desc->lba = (iop.lba_capacity << 16) | (iop.lba_capacity >> 16); 664 #else /* ! __BIG_ENDIAN */ 665 /* 666 * do not swap shorts on little endian 667 * 668 * See CF+ and CompactFlash Specification Revision 2.0: 669 * 6.2.1.6: Identfy Drive, Table 39, Word Address 57-58 for details. 670 */ 671 dev_desc->lba = iop.lba_capacity; 672 #endif /* __BIG_ENDIAN */ 673 674 #ifdef CONFIG_LBA48 675 if (iop.command_set_2 & 0x0400) { /* LBA 48 support */ 676 dev_desc->lba48 = 1; 677 dev_desc->lba = (unsigned long long) iop.lba48_capacity[0] | 678 ((unsigned long long) iop.lba48_capacity[1] << 16) | 679 ((unsigned long long) iop.lba48_capacity[2] << 32) | 680 ((unsigned long long) iop.lba48_capacity[3] << 48); 681 } else { 682 dev_desc->lba48 = 0; 683 } 684 #endif /* CONFIG_LBA48 */ 685 /* assuming HD */ 686 dev_desc->type = DEV_TYPE_HARDDISK; 687 dev_desc->blksz = ATA_BLOCKSIZE; 688 dev_desc->log2blksz = LOG2(dev_desc->blksz); 689 dev_desc->lun = 0; /* just to fill something in... */ 690 691 #if 0 /* only used to test the powersaving mode, 692 * if enabled, the drive goes after 5 sec 693 * in standby mode */ 694 ide_outb(device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device)); 695 c = ide_wait(device, IDE_TIME_OUT); 696 ide_outb(device, ATA_SECT_CNT, 1); 697 ide_outb(device, ATA_LBA_LOW, 0); 698 ide_outb(device, ATA_LBA_MID, 0); 699 ide_outb(device, ATA_LBA_HIGH, 0); 700 ide_outb(device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device)); 701 ide_outb(device, ATA_COMMAND, 0xe3); 702 udelay(50); 703 c = ide_wait(device, IDE_TIME_OUT); /* can't take over 500 ms */ 704 #endif 705 } 706 707 __weak void ide_outb(int dev, int port, unsigned char val) 708 { 709 debug("ide_outb (dev= %d, port= 0x%x, val= 0x%02x) : @ 0x%08lx\n", 710 dev, port, val, 711 (ATA_CURR_BASE(dev) + CONFIG_SYS_ATA_PORT_ADDR(port))); 712 713 #if defined(CONFIG_IDE_AHB) 714 if (port) { 715 /* write command */ 716 ide_write_register(dev, port, val); 717 } else { 718 /* write data */ 719 outb(val, (ATA_CURR_BASE(dev))); 720 } 721 #else 722 outb(val, (ATA_CURR_BASE(dev) + CONFIG_SYS_ATA_PORT_ADDR(port))); 723 #endif 724 } 725 726 __weak unsigned char ide_inb(int dev, int port) 727 { 728 uchar val; 729 730 #if defined(CONFIG_IDE_AHB) 731 val = ide_read_register(dev, port); 732 #else 733 val = inb((ATA_CURR_BASE(dev) + CONFIG_SYS_ATA_PORT_ADDR(port))); 734 #endif 735 736 debug("ide_inb (dev= %d, port= 0x%x) : @ 0x%08lx -> 0x%02x\n", 737 dev, port, 738 (ATA_CURR_BASE(dev) + CONFIG_SYS_ATA_PORT_ADDR(port)), val); 739 return val; 740 } 741 742 void ide_init(void) 743 { 744 unsigned char c; 745 int i, bus; 746 747 #ifdef CONFIG_IDE_PREINIT 748 WATCHDOG_RESET(); 749 750 if (ide_preinit()) { 751 puts("ide_preinit failed\n"); 752 return; 753 } 754 #endif /* CONFIG_IDE_PREINIT */ 755 756 WATCHDOG_RESET(); 757 758 /* ATAPI Drives seems to need a proper IDE Reset */ 759 ide_reset(); 760 761 /* 762 * Wait for IDE to get ready. 763 * According to spec, this can take up to 31 seconds! 764 */ 765 for (bus = 0; bus < CONFIG_SYS_IDE_MAXBUS; ++bus) { 766 int dev = 767 bus * (CONFIG_SYS_IDE_MAXDEVICE / 768 CONFIG_SYS_IDE_MAXBUS); 769 770 printf("Bus %d: ", bus); 771 772 ide_bus_ok[bus] = 0; 773 774 /* Select device 775 */ 776 udelay(100000); /* 100 ms */ 777 ide_outb(dev, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(dev)); 778 udelay(100000); /* 100 ms */ 779 i = 0; 780 do { 781 udelay(10000); /* 10 ms */ 782 783 c = ide_inb(dev, ATA_STATUS); 784 i++; 785 if (i > (ATA_RESET_TIME * 100)) { 786 puts("** Timeout **\n"); 787 return; 788 } 789 if ((i >= 100) && ((i % 100) == 0)) 790 putc('.'); 791 792 } while (c & ATA_STAT_BUSY); 793 794 if (c & (ATA_STAT_BUSY | ATA_STAT_FAULT)) { 795 puts("not available "); 796 debug("Status = 0x%02X ", c); 797 #ifndef CONFIG_ATAPI /* ATAPI Devices do not set DRDY */ 798 } else if ((c & ATA_STAT_READY) == 0) { 799 puts("not available "); 800 debug("Status = 0x%02X ", c); 801 #endif 802 } else { 803 puts("OK "); 804 ide_bus_ok[bus] = 1; 805 } 806 WATCHDOG_RESET(); 807 } 808 809 putc('\n'); 810 811 for (i = 0; i < CONFIG_SYS_IDE_MAXDEVICE; ++i) { 812 ide_dev_desc[i].type = DEV_TYPE_UNKNOWN; 813 ide_dev_desc[i].if_type = IF_TYPE_IDE; 814 ide_dev_desc[i].devnum = i; 815 ide_dev_desc[i].part_type = PART_TYPE_UNKNOWN; 816 ide_dev_desc[i].blksz = 0; 817 ide_dev_desc[i].log2blksz = 818 LOG2_INVALID(typeof(ide_dev_desc[i].log2blksz)); 819 ide_dev_desc[i].lba = 0; 820 #ifndef CONFIG_BLK 821 ide_dev_desc[i].block_read = ide_read; 822 ide_dev_desc[i].block_write = ide_write; 823 #endif 824 if (!ide_bus_ok[IDE_BUS(i)]) 825 continue; 826 ide_ident(&ide_dev_desc[i]); 827 dev_print(&ide_dev_desc[i]); 828 829 #ifndef CONFIG_BLK 830 if ((ide_dev_desc[i].lba > 0) && (ide_dev_desc[i].blksz > 0)) { 831 /* initialize partition type */ 832 part_init(&ide_dev_desc[i]); 833 } 834 #endif 835 } 836 WATCHDOG_RESET(); 837 838 #ifdef CONFIG_BLK 839 struct udevice *dev; 840 841 uclass_first_device(UCLASS_IDE, &dev); 842 #endif 843 } 844 845 /* We only need to swap data if we are running on a big endian cpu. */ 846 #if defined(__LITTLE_ENDIAN) 847 __weak void ide_input_swap_data(int dev, ulong *sect_buf, int words) 848 { 849 ide_input_data(dev, sect_buf, words); 850 } 851 #else 852 __weak void ide_input_swap_data(int dev, ulong *sect_buf, int words) 853 { 854 volatile ushort *pbuf = 855 (ushort *)(ATA_CURR_BASE(dev) + ATA_DATA_REG); 856 ushort *dbuf = (ushort *)sect_buf; 857 858 debug("in input swap data base for read is %lx\n", 859 (unsigned long) pbuf); 860 861 while (words--) { 862 #ifdef __MIPS__ 863 *dbuf++ = swab16p((u16 *)pbuf); 864 *dbuf++ = swab16p((u16 *)pbuf); 865 #else 866 *dbuf++ = ld_le16(pbuf); 867 *dbuf++ = ld_le16(pbuf); 868 #endif /* !MIPS */ 869 } 870 } 871 #endif /* __LITTLE_ENDIAN */ 872 873 874 #if defined(CONFIG_IDE_SWAP_IO) 875 __weak void ide_output_data(int dev, const ulong *sect_buf, int words) 876 { 877 ushort *dbuf; 878 volatile ushort *pbuf; 879 880 pbuf = (ushort *)(ATA_CURR_BASE(dev) + ATA_DATA_REG); 881 dbuf = (ushort *)sect_buf; 882 while (words--) { 883 EIEIO; 884 *pbuf = *dbuf++; 885 EIEIO; 886 *pbuf = *dbuf++; 887 } 888 } 889 #else /* ! CONFIG_IDE_SWAP_IO */ 890 __weak void ide_output_data(int dev, const ulong *sect_buf, int words) 891 { 892 #if defined(CONFIG_IDE_AHB) 893 ide_write_data(dev, sect_buf, words); 894 #else 895 outsw(ATA_CURR_BASE(dev) + ATA_DATA_REG, sect_buf, words << 1); 896 #endif 897 } 898 #endif /* CONFIG_IDE_SWAP_IO */ 899 900 #if defined(CONFIG_IDE_SWAP_IO) 901 __weak void ide_input_data(int dev, ulong *sect_buf, int words) 902 { 903 ushort *dbuf; 904 volatile ushort *pbuf; 905 906 pbuf = (ushort *)(ATA_CURR_BASE(dev) + ATA_DATA_REG); 907 dbuf = (ushort *)sect_buf; 908 909 debug("in input data base for read is %lx\n", (unsigned long) pbuf); 910 911 while (words--) { 912 EIEIO; 913 *dbuf++ = *pbuf; 914 EIEIO; 915 *dbuf++ = *pbuf; 916 } 917 } 918 #else /* ! CONFIG_IDE_SWAP_IO */ 919 __weak void ide_input_data(int dev, ulong *sect_buf, int words) 920 { 921 #if defined(CONFIG_IDE_AHB) 922 ide_read_data(dev, sect_buf, words); 923 #else 924 insw(ATA_CURR_BASE(dev) + ATA_DATA_REG, sect_buf, words << 1); 925 #endif 926 } 927 928 #endif /* CONFIG_IDE_SWAP_IO */ 929 930 #ifdef CONFIG_BLK 931 ulong ide_read(struct udevice *dev, lbaint_t blknr, lbaint_t blkcnt, 932 void *buffer) 933 #else 934 ulong ide_read(struct blk_desc *block_dev, lbaint_t blknr, lbaint_t blkcnt, 935 void *buffer) 936 #endif 937 { 938 #ifdef CONFIG_BLK 939 struct blk_desc *block_dev = dev_get_uclass_platdata(dev); 940 #endif 941 int device = block_dev->devnum; 942 ulong n = 0; 943 unsigned char c; 944 unsigned char pwrsave = 0; /* power save */ 945 946 #ifdef CONFIG_LBA48 947 unsigned char lba48 = 0; 948 949 if (blknr & 0x0000fffff0000000ULL) { 950 /* more than 28 bits used, use 48bit mode */ 951 lba48 = 1; 952 } 953 #endif 954 debug("ide_read dev %d start " LBAF ", blocks " LBAF " buffer at %lX\n", 955 device, blknr, blkcnt, (ulong) buffer); 956 957 /* Select device 958 */ 959 ide_outb(device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device)); 960 c = ide_wait(device, IDE_TIME_OUT); 961 962 if (c & ATA_STAT_BUSY) { 963 printf("IDE read: device %d not ready\n", device); 964 goto IDE_READ_E; 965 } 966 967 /* first check if the drive is in Powersaving mode, if yes, 968 * increase the timeout value */ 969 ide_outb(device, ATA_COMMAND, ATA_CMD_CHK_PWR); 970 udelay(50); 971 972 c = ide_wait(device, IDE_TIME_OUT); /* can't take over 500 ms */ 973 974 if (c & ATA_STAT_BUSY) { 975 printf("IDE read: device %d not ready\n", device); 976 goto IDE_READ_E; 977 } 978 if ((c & ATA_STAT_ERR) == ATA_STAT_ERR) { 979 printf("No Powersaving mode %X\n", c); 980 } else { 981 c = ide_inb(device, ATA_SECT_CNT); 982 debug("Powersaving %02X\n", c); 983 if (c == 0) 984 pwrsave = 1; 985 } 986 987 988 while (blkcnt-- > 0) { 989 c = ide_wait(device, IDE_TIME_OUT); 990 991 if (c & ATA_STAT_BUSY) { 992 printf("IDE read: device %d not ready\n", device); 993 break; 994 } 995 #ifdef CONFIG_LBA48 996 if (lba48) { 997 /* write high bits */ 998 ide_outb(device, ATA_SECT_CNT, 0); 999 ide_outb(device, ATA_LBA_LOW, (blknr >> 24) & 0xFF); 1000 #ifdef CONFIG_SYS_64BIT_LBA 1001 ide_outb(device, ATA_LBA_MID, (blknr >> 32) & 0xFF); 1002 ide_outb(device, ATA_LBA_HIGH, (blknr >> 40) & 0xFF); 1003 #else 1004 ide_outb(device, ATA_LBA_MID, 0); 1005 ide_outb(device, ATA_LBA_HIGH, 0); 1006 #endif 1007 } 1008 #endif 1009 ide_outb(device, ATA_SECT_CNT, 1); 1010 ide_outb(device, ATA_LBA_LOW, (blknr >> 0) & 0xFF); 1011 ide_outb(device, ATA_LBA_MID, (blknr >> 8) & 0xFF); 1012 ide_outb(device, ATA_LBA_HIGH, (blknr >> 16) & 0xFF); 1013 1014 #ifdef CONFIG_LBA48 1015 if (lba48) { 1016 ide_outb(device, ATA_DEV_HD, 1017 ATA_LBA | ATA_DEVICE(device)); 1018 ide_outb(device, ATA_COMMAND, ATA_CMD_READ_EXT); 1019 1020 } else 1021 #endif 1022 { 1023 ide_outb(device, ATA_DEV_HD, ATA_LBA | 1024 ATA_DEVICE(device) | ((blknr >> 24) & 0xF)); 1025 ide_outb(device, ATA_COMMAND, ATA_CMD_READ); 1026 } 1027 1028 udelay(50); 1029 1030 if (pwrsave) { 1031 /* may take up to 4 sec */ 1032 c = ide_wait(device, IDE_SPIN_UP_TIME_OUT); 1033 pwrsave = 0; 1034 } else { 1035 /* can't take over 500 ms */ 1036 c = ide_wait(device, IDE_TIME_OUT); 1037 } 1038 1039 if ((c & (ATA_STAT_DRQ | ATA_STAT_BUSY | ATA_STAT_ERR)) != 1040 ATA_STAT_DRQ) { 1041 printf("Error (no IRQ) dev %d blk " LBAF 1042 ": status %#02x\n", device, blknr, c); 1043 break; 1044 } 1045 1046 ide_input_data(device, buffer, ATA_SECTORWORDS); 1047 (void) ide_inb(device, ATA_STATUS); /* clear IRQ */ 1048 1049 ++n; 1050 ++blknr; 1051 buffer += ATA_BLOCKSIZE; 1052 } 1053 IDE_READ_E: 1054 return n; 1055 } 1056 1057 #ifdef CONFIG_BLK 1058 ulong ide_write(struct udevice *dev, lbaint_t blknr, lbaint_t blkcnt, 1059 const void *buffer) 1060 #else 1061 ulong ide_write(struct blk_desc *block_dev, lbaint_t blknr, lbaint_t blkcnt, 1062 const void *buffer) 1063 #endif 1064 { 1065 #ifdef CONFIG_BLK 1066 struct blk_desc *block_dev = dev_get_uclass_platdata(dev); 1067 #endif 1068 int device = block_dev->devnum; 1069 ulong n = 0; 1070 unsigned char c; 1071 1072 #ifdef CONFIG_LBA48 1073 unsigned char lba48 = 0; 1074 1075 if (blknr & 0x0000fffff0000000ULL) { 1076 /* more than 28 bits used, use 48bit mode */ 1077 lba48 = 1; 1078 } 1079 #endif 1080 1081 /* Select device 1082 */ 1083 ide_outb(device, ATA_DEV_HD, ATA_LBA | ATA_DEVICE(device)); 1084 1085 while (blkcnt-- > 0) { 1086 c = ide_wait(device, IDE_TIME_OUT); 1087 1088 if (c & ATA_STAT_BUSY) { 1089 printf("IDE read: device %d not ready\n", device); 1090 goto WR_OUT; 1091 } 1092 #ifdef CONFIG_LBA48 1093 if (lba48) { 1094 /* write high bits */ 1095 ide_outb(device, ATA_SECT_CNT, 0); 1096 ide_outb(device, ATA_LBA_LOW, (blknr >> 24) & 0xFF); 1097 #ifdef CONFIG_SYS_64BIT_LBA 1098 ide_outb(device, ATA_LBA_MID, (blknr >> 32) & 0xFF); 1099 ide_outb(device, ATA_LBA_HIGH, (blknr >> 40) & 0xFF); 1100 #else 1101 ide_outb(device, ATA_LBA_MID, 0); 1102 ide_outb(device, ATA_LBA_HIGH, 0); 1103 #endif 1104 } 1105 #endif 1106 ide_outb(device, ATA_SECT_CNT, 1); 1107 ide_outb(device, ATA_LBA_LOW, (blknr >> 0) & 0xFF); 1108 ide_outb(device, ATA_LBA_MID, (blknr >> 8) & 0xFF); 1109 ide_outb(device, ATA_LBA_HIGH, (blknr >> 16) & 0xFF); 1110 1111 #ifdef CONFIG_LBA48 1112 if (lba48) { 1113 ide_outb(device, ATA_DEV_HD, 1114 ATA_LBA | ATA_DEVICE(device)); 1115 ide_outb(device, ATA_COMMAND, ATA_CMD_WRITE_EXT); 1116 1117 } else 1118 #endif 1119 { 1120 ide_outb(device, ATA_DEV_HD, ATA_LBA | 1121 ATA_DEVICE(device) | ((blknr >> 24) & 0xF)); 1122 ide_outb(device, ATA_COMMAND, ATA_CMD_WRITE); 1123 } 1124 1125 udelay(50); 1126 1127 /* can't take over 500 ms */ 1128 c = ide_wait(device, IDE_TIME_OUT); 1129 1130 if ((c & (ATA_STAT_DRQ | ATA_STAT_BUSY | ATA_STAT_ERR)) != 1131 ATA_STAT_DRQ) { 1132 printf("Error (no IRQ) dev %d blk " LBAF 1133 ": status %#02x\n", device, blknr, c); 1134 goto WR_OUT; 1135 } 1136 1137 ide_output_data(device, buffer, ATA_SECTORWORDS); 1138 c = ide_inb(device, ATA_STATUS); /* clear IRQ */ 1139 ++n; 1140 ++blknr; 1141 buffer += ATA_BLOCKSIZE; 1142 } 1143 WR_OUT: 1144 return n; 1145 } 1146 1147 #if defined(CONFIG_OF_IDE_FIXUP) 1148 int ide_device_present(int dev) 1149 { 1150 if (dev >= CONFIG_SYS_IDE_MAXBUS) 1151 return 0; 1152 return ide_dev_desc[dev].type == DEV_TYPE_UNKNOWN ? 0 : 1; 1153 } 1154 #endif 1155 1156 #ifdef CONFIG_BLK 1157 static int ide_blk_probe(struct udevice *udev) 1158 { 1159 struct blk_desc *desc = dev_get_uclass_platdata(udev); 1160 1161 /* fill in device vendor/product/rev strings */ 1162 strncpy(desc->vendor, ide_dev_desc[desc->devnum].vendor, 1163 BLK_VEN_SIZE); 1164 desc->vendor[BLK_VEN_SIZE] = '\0'; 1165 strncpy(desc->product, ide_dev_desc[desc->devnum].product, 1166 BLK_PRD_SIZE); 1167 desc->product[BLK_PRD_SIZE] = '\0'; 1168 strncpy(desc->revision, ide_dev_desc[desc->devnum].revision, 1169 BLK_REV_SIZE); 1170 desc->revision[BLK_REV_SIZE] = '\0'; 1171 1172 part_init(desc); 1173 1174 return 0; 1175 } 1176 1177 static const struct blk_ops ide_blk_ops = { 1178 .read = ide_read, 1179 .write = ide_write, 1180 }; 1181 1182 U_BOOT_DRIVER(ide_blk) = { 1183 .name = "ide_blk", 1184 .id = UCLASS_BLK, 1185 .ops = &ide_blk_ops, 1186 .probe = ide_blk_probe, 1187 }; 1188 1189 static int ide_probe(struct udevice *udev) 1190 { 1191 struct udevice *blk_dev; 1192 char name[20]; 1193 int blksz; 1194 lbaint_t size; 1195 int i; 1196 int ret; 1197 1198 for (i = 0; i < CONFIG_SYS_IDE_MAXDEVICE; i++) { 1199 if (ide_dev_desc[i].type != DEV_TYPE_UNKNOWN) { 1200 sprintf(name, "blk#%d", i); 1201 1202 blksz = ide_dev_desc[i].blksz; 1203 size = blksz * ide_dev_desc[i].lba; 1204 1205 /* 1206 * With CDROM, if there is no CD inserted, blksz will 1207 * be zero, don't bother to create IDE block device. 1208 */ 1209 if (!blksz) 1210 continue; 1211 ret = blk_create_devicef(udev, "ide_blk", name, 1212 IF_TYPE_IDE, i, 1213 blksz, size, &blk_dev); 1214 if (ret) 1215 return ret; 1216 } 1217 } 1218 1219 return 0; 1220 } 1221 1222 U_BOOT_DRIVER(ide) = { 1223 .name = "ide", 1224 .id = UCLASS_IDE, 1225 .probe = ide_probe, 1226 }; 1227 1228 struct pci_device_id ide_supported[] = { 1229 { PCI_DEVICE_CLASS(PCI_CLASS_STORAGE_IDE << 8, 0xffff00) }, 1230 { } 1231 }; 1232 1233 U_BOOT_PCI_DEVICE(ide, ide_supported); 1234 1235 UCLASS_DRIVER(ide) = { 1236 .name = "ide", 1237 .id = UCLASS_IDE, 1238 }; 1239 #else 1240 U_BOOT_LEGACY_BLK(ide) = { 1241 .if_typename = "ide", 1242 .if_type = IF_TYPE_IDE, 1243 .max_devs = CONFIG_SYS_IDE_MAXDEVICE, 1244 .desc = ide_dev_desc, 1245 }; 1246 #endif 1247