1BUBT (Burn ATF) command 2-------------------------- 3Bubt command is used to burn a new ATF image to flash device. 4 5The bubt command gets the following parameters: ATF file name, destination device and source device. 6bubt [file-name] [destination [source]] 7 - file-name Image file name to burn. default = flash-image.bin 8 - destination Flash to burn to [spi, nand, mmc]. default = active flash 9 - source Source to load image from [tftp, usb]. default = tftp 10 11Examples: 12 bubt - Burn flash-image.bin from tftp to active flash 13 bubt latest-spi.bin nand - Burn latest-spi.bin from tftp to NAND flash 14 15Notes: 16- For the TFTP interface set serverip and ipaddr. 17- To burn image to SD/eMMC device, the target is defined 18 by parameters CONFIG_SYS_MMC_ENV_DEV and CONFIG_SYS_MMC_ENV_PART. 19 20Bubt command details (burn image step by-step) 21---------------------------------------------- 22This section describes bubt command flow: 23 241. Fetch the requested ATF image from an available interface (USB/SD/SATA/XDB, etc.) 25 into the DRAM, and place it at <load_address> 26 Example: when using the FAT file system on USB flash device: 27 # usb reset 28 # fatls usb 0 (see files in device) 29 # fatload usb 0 <load_address> <file_name> 30 312. Erase the target device: 32 - NAND: # nand erase 0 100000 33 - SPI: # sf probe 0 34 # sf erase 0 100000 35 - SD/eMMC: # mmc dev <dev_id> <boot_partition> 36 37Notes: 38- The eMMC has 2 boot partitions (BOOT0 and BOOT1) and a user data partition (DATA). 39 The boot partitions are numbered as partition 1 and 2 in MMC driver. 40 Number 0 is used for user data partition and should not be utilized for storing 41 boot images and U-Boot environment in RAW mode since it will break file system 42 structures usually located here. 43 The default boot partition is BOOT0. It is selected by the following parameter: 44 CONFIG_SYS_MMC_ENV_PART=1 45 Valid values for this parameter are 1 for BOOT0 and 2 for BOOT1. 46 Please never use partition number 0 here! 47 The eMMC has 2 boot partitions (BOOT0 and BOOT1) and a user data partition (DATA). 48 The boot partitions are numbered as partition 1 and 2 in MMC driver. 49 Number 0 is used for user data partition and should not be utilized for storing 50 boot images and U-Boot environment in RAW mode since it will break file system 51 structures usually located here. 52 The default boot partition is BOOT0. It is selected by the following parameter: 53 CONFIG_SYS_MMC_ENV_PART=1 54 Valid values for this parameter are 1 for BOOT0 and 2 for BOOT1. 55 Please never use partition number 0 here! 56- The partition number is ignored if the target device is SD card. 57- The boot image offset starts at block 0 for eMMC and block 1 for SD devices. 58 The block 0 on SD devices is left for MBR storage. 59 603. Write the ATF image: 61 - NAND: # nand write <load_address> 0 <ATF Size> 62 - SPI: # sf write <load_address> 0 <ATF Size> 63 - SD/eMMC: # mmc write <load_address> [0|1] <ATF Size>/<block_size> 64 65